Berkel X13E-PLUS Manuel utilisateur

Marque: Berkel

Modèle: X13E-PLUS

Taper: Manuel utilisateur

Ce manuel convient également à

F35290 Rev. A (August 2014)

MODELS

X13E-PLUS &

X13AE-PLUS

LICERS

OWNER/OPERATOR

MANUAL

IMPORTANT NOTICE

This manual contains Important Safety

Instructions which must be strictly

followed when using this equipment.

NOTICIA IMPORTANTE

Este manual contiene importantes instrucciones

de seguridad que deben ser seguidas el pie de la

letra cuando utilice esta maquina.

BEFORE USING THIS EQUIPMENT

Berkel’s slicers are designed to slice meat and other food products safely and

efﬁ ciently. However, unless the operator is properly trained and supervised,

there is the possibility of a serious injury. It is the responsibility of the owner

to ensure that this slicer is used properly and safely, strictly following the

instructions contained in this manual and any requirements of local law.

No one should use or service this slicer without proper training and supervi -

sion. All operators should be thoroughly familiar with the procedures con-

tained in this manual. Even so, Berkel cannot anticipate every circumstance or

environment in which its slicers will be used. You, the owner and/or operator,

must remain alert to the hazards posed by the function of a slicer—particu-

larly the sharp rotating blade and moving table. No one uner 18 years of age

should operate this equipment. If you are uncertain about a particular task, ask

your supervisor.

This manual contains a number of safe practices in the General Safety Instruc-

tion Section. Additional warnings are placed throughout this manual. WAR N-

INGS RELATED TO YOUR PERSONAL SAFETY ARE INDICATED

BY:

WA R N I NG

If any warning label, wall chart or manual becomes misplaced, damaged or

illegible, please contact your nearest distributor or Berkel directly, for a free

replacement.

Remember, however, THIS MANUAL OR THE WARNING LABELS DO

NOT REPLACE THE NEED TO BE ALERT AND TO USE YOUR

COMMON SENSE WHEN USING THIS SLICER.

TABLE OF CONTENTS

Page

General Safety Instructions ......................................................................................................................... 2

Equipment Description ................................................................................................................................ 4

Intended Uses and Characteristics .............................................................................................................. 6

Unpacking and Installation ......................................................................................................................... 6

Operation ..................................................................................................................................................... 7

Cleaning and Sanitizing .............................................................................................................................. 8

Shar pening ................................................................................................................................................. 10

Repair Parts/Repair Service ...................................................................................................................... 10

Troubleshooting ..........................................................................................................................................11

Speciﬁ cations ............................................................................................................................................. 12

Optional Accessories ................................................................................................................................. 13

Warranty .................................................................................................................................................... 14

The Berkel Company • World’s Leading Manufacturer of Slicers and Food Processing Equipment

BERKEL COMPANY

2006 Northwestern Parkway • Louisville, KY 40201

Phone: 800-348-0251 • Fax 888-888-2838

www.berkelequipment.com

Printed in USA Berkel Company Part No. 0F-35290

2 • X13E-PLUS & X13AE-PLUS OWNER/OPERATOR MANUAL

PELIGRO

CUCHILLA FILOSA

para evitar serios accidentes a su

persona siga las instrucciones de este

manual y

1. NUNCA utilice esta mçquina sin previa instrucciùn y autorizaciùn de su

supervisor.

2. LA MçQUINA DEBE apoyarse sobre un nivel solido y plano.

3. LOS PROTECTORES deben colocarse ANTES de enchufar y operar la

mçquina.

4. SIEMPRE utilice el enchufe original proveido por el fabricante.

5. SIEMPRE utilice el utensillo para empujar la

comida - nunca su mano.

6. NUNCA TOQUE LA CUCHILLA CON

LA MANO.

7. MANTENGA manos, brazos, cabello y

ropa suelta LEJOS de toda parte en movimiento

de la mçquina.

8. EN CASO DE QUE LA MÇQUINA SE TRABE,

apague y desconecte ANTES de sacar lo que la obstruye.

9. APAGUE Y DESCONECTE LA MçQUINA antes de limpiar,

sanitizar, o arreglar.

10. UTILIZE UNICAMENTE los repuestos provistos por el fabricante.

11. EN CASO de que los membretes de ‘PELIGRO’ se desprendan

de la mçquina o sean illegibles, llame al fabricante o a su

representante de service Berkel para que lo reemplace sin cargo.

X13E-PLUS & X13AE-PLUS OWNER/OPERATOR MANUAL • 3

WAR NING

SHARP KNIFE BLADE

to avoid serious personal injury

follow all the instructions in this manual

and

1. NEVER touch this machine without training and authorization by your

supervisor.

2. MACHINE MUST BE on solid level support.

3. GUARDS MUST BE in place before plugging in and turning on machine.

4. ALWAYS use three pronged plug provided.

5. ALWAYS use food pusher not your hand.

6. NEVER TOUCH ROTATING KNIFE.

7. KEEP hands, arms, hair and loose clothing

clear of all moving parts.

8. SHOULD MACHINE JAM, turn off and unplug

before removing obstruction.

9. TURN OFF AND UNPLUG machine from power source before cleaning,

sanitizing or servicing.

10. USE ONLY the attachments provided by the manufacturer.

11. SHOULD any warning label on a machine come off or become unreadable,

contact the manufacturer or your Designated Berkel Service Location for a free

replacement.

EQUIPMENT DESCRIPTION

4 • X13E-PLUS & X13AE-PLUS OWNER/OPERATOR MANUAL

EQUIPMENT DESCRIPTION

X13E-PLUS & X13AE-PLUS OWNER/OPERATOR MANUAL • 5

Intended Uses and Characteristics

Intended Uses

The model X13E-PLUS and X13AE-PLUS slicers are designed for cutting the following types of prod-

ucts:

•

Meat (without bones)

•

Cheese

•

Vegetables

The following types of items are NOT suitable for slicing on the Model X13E-PLUS or X13AE-PLUS

slicers:

•

Non-food products

•

Frozen foods

•

Bone in products

Special Features/Characteristics

Reduced seams and joints for better sanitation

Left hand thickness adjustment for easier cleaning and better user interface

Kick stand for cleaning under the slicer

3 slicing speeds (automatic only)

3 slicing stroke lengths (automatic only)

Automatic return to home at the end of the cutting cycle (automatic only)

Unpacking and Installation

Note: Immediately after unpacking, check the slicer for shipping damage. If the equipment is

found to be damaged, save everything! Notify the carrier within 5 days of delivery.

1. Carefully remove the cardboard carton from around the slicer.

2. Slide the product table off the gauge plate. It is in the cardboard box on the gauge plate.

3. Get assistance from another individual and place the slicer on a solid, level surface that is free of

any obstructions.

4. Make sure to unpack the sharpener, fence and brush. They are located in pockets in the cardboard

base.

5. Slide the product table onto the support arm and secure using the red product table locking knob.

WARNING

To eliminate a potential shock hazard, a properly grounded outlet using the three-pronged plug

provided must power this unit. Before plugging the slicer in, check your outlet voltage to be sure it

complies with the voltage speciﬁ ed on the serial number plate on the slicer.

Note: The model/serial number plate is located on the back of the slicer.

6 • X13E-PLUS & X13AE-PLUS OWNER/OPERATOR MANUAL

Operation

General

1. Check to see that the center plate and product table are in place on the slicer and the gauge plate is

completely closed. The holes in the bottom of the center plate ﬁ t over the bottom mounting studs in

the ring guard and the center plate locking knob is at the top of the center plate. The product table

slides completely onto the support arm and is secured with the red product table locking knob.

2. If the slicer is an automatic, then make sure the automatic engage knob on the right side of the table

support arm is pushed in, towards the left.

3. Plug the slicer in. The pilot light, between the start and stop buttons will illuminate.

4. Push the green ON button and the slicer blade will start to turn. Press the red STOP button to stop

the knife.

Automatic Operation

5. If you have an automatic slicer, with the slicer stopped, pull the automatic engage knob fully out on

the right side of the machine. This will put the slicer in the automatic mode.

6. Push the speed selection button to change the speed:

One illuminated LED indicates 20 slicers per minute (slow speed)

Two illuminated LED’s indicates 40 slices per minute (medium speed)

Three illuminated LED’s indicates 60 slices per minute (high speed)

7. Pushing the stroke length selection button changes the length of the stroke. This allows smaller

products to be sliced quicker, without the table moving any faster. Make sure the stroke length is

longer than the width of the product.

One illuminated LED indicates 1/3 of the total possible stroke length

Two illuminated LED’s indicates 2/3 total possible stroke length

Three illuminated LED’s indicates full stroke length

8. Press the green START button and the product table will slowly come to its forward position to ﬁ nd

its home position. Once it gets back to the home position, then it will start to go back and forth at

the preset speed and stroke length.

9. Push the red STOP button and the table will complete its stroke and stop in the home position.

10. As long as the slicer remains in the automatic mode it will remember its home position and always

start right up when the green START button is pushed. It will always start slow and gradually build

up to its full speed. This is the “soft start” feature.

11. Each time you take the slicer out of the automatic mode, and then back into the automatic mode, it

will always ﬁ nd its home position before it starts to run (as indicated in step #8).

12. Each time you activate the slicer into automatic mode, the last speed and stroke length settings will

be remembered until power is disrupted from the slicer (i.e. disconnecting the power cord from

the outlet). Once power is reconnected to the slicer, the default for automatic is slow speed and full

stroke length.

X13E-PLUS & X13AE-PLUS OWNER/OPERATOR MANUAL • 7

Cleaning and Sanitizing

The following cleaning procedures have been prepared with the grateful

cooperation of Kay Chemical, an Ecolab company.

Frequency:

The slicer shall be cleaned and sanitized at intervals to comply with national, state and/or local health codes.

Supplies:

Dish Detergent such as KAY

Pot & Pan Detergent

Sanitizer such as KAYQUAT

Nonabrasive Pad

Nylon Brush

Cut-Resistant gloves

Cloth wipes

Note: Sanitizer concentration shall comply with Section 4-501.114, Manual and Mechanical Warewashing

Equipment, Chemical Sanitization – Temperature, pH, Concentration, and Hardness of the FDA Food Code. If a

chemical sanitizer other than chlorine, iodine, or quaternary ammonium is used, it shall be applied in accordance

with the EPA-registered label use instructions.

Procedure:

CAUTION: Use extreme care when cleaning blade.

1. Close the slicer thickness control knob.

2. Turn the slicer off and unplug power cord from the wall outlet.

3. Pull the product table to the front of the slicer. If it is an automatic slicer, make sure the engagement

knob is in the manual position before pulling the product table to the front of the slicer.

4. Unscrew the red handle from the pusher and remove the pusher from the pusher arm. Unscrew and

remove the pusher arm slide rod from the product table. Loosen the product table locking knob and

remove the table. The product table cannot be removed unless it is fully forward and the thickness

control knob is completely closed.

5. Remove the center plate by lifting the center plate locking knob at the top of the center plate and lift

from the slicer.

6. Pre-scrape food from removable product table and center plate.

7. Wash center plate, product table, red handle, pusher, pusher arm, and slide rod in hot detergent solution.

The sharpener can be submerged in the hot detergent solution for cleaning.

8. Rinse the center plate, product table, red handle, pusher, pusher arm, slide rod, and sharpener in fresh,

hot, potable water.

9. Submerge the center plate, product table, red handle, pusher, pusher arm, slide rod, and sharpener in

sanitizer solution. Set parts to the side on a sanitized surface and allow to air dry.

8 • X13E-PLUS & X13AE-PLUS OWNER/OPERATOR MANUAL

10. Put on cut resistant gloves. Pre-scrape food from slicer.

11. Using fresh detergent solution, clean the front side of the knife with a non-abrasive pad, nylon brush,

and/or cloth wipes. Always wipe from the center of the knife to the outer edge.

12. Clean the backside of the knife with the fresh detergent solution, non-abrasive pad, nylon brush, and/or

cloth wipes.

13. Fold a cloth wipe that has been submerged in fresh detergent solution and work it between the ring

guard and knife, starting at the base of the ring guard. Carefully work the cloth around the knife,

cleaning the edge of the knife, edge of the ring guard and edge of the gauge plate. Use extreme cau-

tion.

14. Clean the rest of the slicer base and other components with the fresh detergent solution and a non-

abrasive pad.

15. Lift up the front of the slicer about 6 inches. A spring loaded kick stand will drop down to the table

surface and hold the front of the slicer up. This will allow you to pre-scrape food and clean the table

surface under the slicer with fresh detergent solution.

16. Using a fresh cloth wipe, rinse slicer and area under slicer with fresh hot potable water.

17. Spray slicer and area under slicer with fresh sanitizer solution from a sanitizer spray bottle and allow to

air dry. Remove cut-resistant gloves.

18. Once the table surface under the slicer has been washed, rinsed and sanitized, lift the front edge of the

slicer and push the kick stand back under the slicer. Slowly lower the slicer back to the table.

19. Slide the pusher arm onto the slide rod and reassemble the pusher to the pusher arm using the red

handle. Reassemble the slide rod to the product table. Reinstall the center plate and the product table to

the slicer. After assembly, spray with sanitizer solution and allow to air dry.

20. Plug in slicer. Place sharpener in proper storage location.

Gasket Inspection:

The recommended interval between inspections shall not exceed six months.

The inspection must be made by the manufacture or an authorized service agent.

WARNING

The slicer must be removed from service until repaired by the manufacture or an authorized service

agent if any gasket or seal is found to be damaged or missing.

X13E-PLUS & X13AE-PLUS OWNER/OPERATOR MANUAL • 9

Sharpening

Sharpen only when necessary. Too frequent or prolonged sharpening will pre-

maturely wear the knife and/or stones. The knife should be sharpened when you

notice wavy slices or excessive scrap. Only sharpen the knife after it has been

cleaned. You cannot effectively sharpen a dirty knife.

1. If it is an automatic slicer, make sure the engagement knob is in the manual

position, by pushing in (to the left) the knob on the right side of the support

arm.

2. Make sure the product table is pulled all the way to the front of the slicer and

the thickness control knob is completely closed.

3. Place the top tab of the sharpener into the slot of the product table. Clip the

bottom clip of the sharpener over the end of the product table.

4. Open the thickness control knob as far as it will go, fully exposing the knife.

5. Turn the slicer on and gently push the product table towards the knife just as

if you were slicing product. Once both the sharpening and deburring stones

make contact with the knife, remain there for 2-3 seconds and then pull the

product table back to the home position.

6. Turn off the slicer and close the thickness control knob.

7. Unclip the sharpener from the product table using the bottom clip. It can be

cleaned in the sink and then stored in a drawer.

8. After sharpening, clean and sanitize the slicer as outlined on page 8.

Repair Parts/Repair Service/Exploded Views

Please contact Hobart Service or your designated Berkel Service Location (DBSL) for any repair

parts/repair service required on your Berkel slicer. For the nearest Hobart service ofﬁ ce, please visit

www.hobartservice.com and then click on “locate an ofﬁ ce”. Then either enter your ZIP CODE or

select a state to ﬁ nd the closest location. Or you can also visit www.berkelequipment.com and click on

the “Service tab”. Then enter your ZIP CODE to be shown the closest Hobart or Berkel DBSL service

locations. Other product information such as Parts Catalogs and Instruction/Operator Manuals are also

available on the www.berkelequipment.com website. Click on the “Resource Center tab”, and then click

on the information category you want to read or download. Be sure to enter your product model number.

Additional information may be obtained from:

Berkel Company

2006 Northwestern Parkway

Louisville, KY 40201

Phone: 800-348-0251

Fax: 888-888-2838

www.berkelequipment.com

10 • X13E-PLUS & X13AE-PLUS OWNER/OPERATOR MANUAL

Troubleshooting

Electrical Failure

1. Is the pilot light illuminated? If not:

• Is the power cord completely plugged into the wall outlet?

• Check the power cord for cuts or breaks.

• Are you getting electricity from the wall outlet? Check by plugging in another piece of equipment

with the same electrical requirements.

2. Is the pilot light illuminated but blinking? If so, then push the stop button and then the start button. If the

light is still blinking,

then contact your nearest Hobart Service location or Designated Berkel Service

location. If you do not know your nearest Hobart Service location or your nearest Designated Berkel

Service Location, then see page 10 for details on whom to contact.

3. If the correction of any of the above conditions does not result in a functional slicer, call Hobart Service or

your Designated Berkel Service Location.

Product table doesn’t move freely

1. Check to make sure the slicer is not in the automatic mode.

Note: The mechanism in the undercarriage should not be oiled or greased.

Pusher is not sliding easily on the rod

1. Check that the rod is clean and apply Berkel oil to the rod.

Knife not sharpening

1. Are sharpening procedures being followed exactly as shown in this manual?

2. Are sharpening stones clean? If not, then remove them from the assembly and clean them thoroughly with

water and a stiff bristled brush. They are left hand threaded nuts.

3. Are sharpening stones worn and not making contact with the knife? If so, then replace them.

4. Is the knife clean? If coated with food fats, the sharpening stones won’t sharpen the knife. Clean the knife

and stones.

X13E-PLUS & X13AE-PLUS OWNER/OPERATOR MANUAL • 11

Speciﬁ cations

Machine Dimensions:

Width 26-3/4" (680mm)

Length 30-1/2" (770mm)

Height 25-1/4" (640mm)

Diameter of Knife: 13" (330mm)

Slice Thickness: 0 to 1-5/16" (33mm)

Slicing Speed (automatic):

Low 20 slices per minute

Medium 40 slices per minute

High 60 slices per minute

Stroke Length (automatic):

Short 5 inches

Medium 9 inches

Full 13 inches

Slicing Capacity:

Square 7-1/2" x 7-1/2" (190mm x 190mm)

Round 8-1/2" (220mm)

Rectangle 10-1/2" x 6-3/4" (265mm x 170mm)

Net Weight:

Manual 88 lbs.

Automatic 98 lbs.

Shipping Weight:

Manual 118 lbs.

Automatic 128 lbs.

Voltage/Amperage: 115/60/1; 5.5 amps

Horsepower: 1/2hp

12 • X13E-PLUS & X13AE-PLUS OWNER/OPERATOR MANUAL

Optional Accessories

VEGETABLE CHUTE (4975-00463)

A vegetable chute is available that ﬁ ts on the product table. The vegetable chute is used for quantity

slicing of various size fruit, meats or vegetables.

TRAYS

SLAW TRAY (3875-00241)

The slaw tray is a deep tray to receive a large quantity of product and retain the juices.

X13E-PLUS & X13AE-PLUS OWNER/OPERATOR MANUAL • 13

F35290 Rev. A (August 2014)

Warranty

Effective: February 14, 2002

Berkel Company (“Berkel”) warrants to the Buyer of new equipment that said equipment,

when installed in accordance with our instructions and subjected to normal use, is free from

defects in material or workmanship for a period of one (1) year from the date of sale.

BERKEL SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY OF

MERCHANTABILITY OR EXPRESS OR IMPLIED WARRANTY OF FITNESS

FOR A PARTICULAR PURPOSE.

Berkel’s obligation and liability under this warranty is expressly limited to repairing or replac-

ing equipment that proves to be defective in material or workmanship within the applicable

warranty period. Berkel or a Designated Berkel Service Location will perform all repairs

pursuant to this warranty. Berkel expressly excludes responsibility for incidental or conse-

quential damages to buyer or any third party, including, without limitation, damages arising

from personal injuries, lost proﬁ ts, loss of business opportunity, loss of property, economic

losses, or statutory or exemplary damages, whether in negligence, warranty, strict liability or

otherwise.

This warranty does not apply to: periodic maintenance of equipment including but not limited

to lubrication, replacement of worn blades, knives, stones, knobs, accessories, and miscella-

neous expendable supply items, and other adjustments required due to installation set-up or

normal wear.

These warranties are given only to the ﬁ rst purchaser from a Berkel Authorized Channel of

Distribution. No warranty is given to subsequent transferees.

The foregoing warranty provisions are a complete and exclusive statement of the warranty

between the buyer and seller. Berkel neither assumes nor authorizes any persons to assume any

other obligation or liability connection with said equipment. This warranty supersedes any and

all prior warranties to the subject hereof.

Model 180 slicers carry a 90-day warranty.

F 35290 Rév. A (Août 2014)

Manuel du propriétaire et

Mode d'eMploi

IMPORTANT NOTICE

This manual contains Important Safety

Instructions which must be strictly

followed when using this equipment.

AVIS IMPORTANT

Ce guide comprend des consignes de sécurité

importantes qui doivent être observées rigoureu-

sement lors de l’utilisation de cet appareil.

trancheuses,

Modèles

X13e-plus &

X13ae-plus

AVANT D’UTILISER CET APPAREIL

Les trancheuses Berkel sont conçues pour trancher des viandes et d'autres produits alimen-

taires de façon efcace et sécuritaire. Il subsiste toutefois un risque de blessure grave si

l'utilisateur n'est pas formé et encadré de façon adéquate. Il en va de la responsabilité du

propriétaire de s'assurer que cette trancheuse soit utilisée correctement et de manière sécu-

ritaire, et de faire en sorte que les opérateurs observent rigoureusement les instructions de

ce guide et respectent toutes les lois locales en vigueur.

Personne ne devrait utiliser ni entretenir cette trancheuse sans supervision adéquate, et

sans avoir suivi une formation appropriée. Tout utilisateur doit bien connaître les procé-

dures présentées dans ce guide. Berkel ne peut toutefois prévoir toutes les situations ni

l’environnement dans lesquels ses trancheuses seront utilisées. C'est donc vous, le pro-

priétaire et/ou l'utilisateur, qui devez demeurer vigilant face aux dangers inhérents à l'uti-

lisation d'une trancheuse, et notamment de la lame rotative très tranchante et du chariot

mobile. Cet appareil ne doit pas être utilisé par une personne de moins de 18 ans. Si vous

avez des doutes à l’égard d’un travail particulier à effectuer, consultez votre superviseur.

Ce guide présente un certain nombre de pratiques sécuritaires rassemblées sous la ru-

brique « Consignes générales de sécurité ». De plus, des avertissements supplémentaires

apparaissent à plusieurs endroits du guide. LES AVERTISSEMENTS CONCERNANT

VOTRE SÉCURITÉ PERSONNELLE SONT SIGNALÉS PAR LA VIGNETTE :

AVERTISSEMENT

Au cas où vous auriez perdu un autocollant d'avertissement, une afche murale ou un

guide d'utilisation, ou encore si l'un de ces derniers devait subir des dommages ou deve-

nir illisible, veuillez contacter le détaillant de votre région, ou Berkel directement, qui les

remplacera gratuitement.

Souvenez-vous toutefois QUE NI CE GUIDE, NI LES AUTOCOLLANTS D'AVER-

TISSEMENT NE SAURAIENT REMPLACER LA NÉCESSITÉ DE DEMEURER

VIGILANT ET DE FAIRE PREUVE DE BON SENS LORS DE L'UTILISATION

DE CETTE TRANCHEUSE.

table des Matières

Page

Consignes générales de sécurité .................................................................................................................. 2

Description de l’appareil .............................................................................................................................. 4

Usages prévus et caractéristiques ................................................................................................................ 6

Déballage et installation .............................................................................................................................. 6

Fonctionnement ........................................................................................................................................... 7

Nettoyage et désinfection ............................................................................................................................ 8

Affûtage ..................................................................................................................................................... 10

Pièces de rechange / Service d’entretien ................................................................................................... 10

Dépannage ..................................................................................................................................................11

Spécications ............................................................................................................................................. 12

Accessoires offerts en option .................................................................................................................... 13

Garantie ..................................................................................................................................................... 14