Samlexpower PST-1000F-12 Le manuel du propriétaire

Catégorie
Adaptateurs secteur
Taper
Le manuel du propriétaire
DC-AC Power
Inverter
Pure Sine Wave
PST-1000F-12
Please read this
manual BEFORE
installing your
inverter
Owner's
Manual
2 | SAMLEX AMERICA INC.
OWNER'S MANUAL | Index
SECTION 1 Safety Instructions ........................................3
SECTION 2 General Information .....................................8
SECTION 3
Limiting Electromagnetic Interference (EMI) ....................... 14
SECTION 4
Powering Direct / Embedded Switch Mode
Power Supplies (SMPS) ....................................................... 15
SECTION 5 Principle of Operation ............................... 17
SECTION 6 Layout ........................................................ 18
SECTION 7
General Information on Lead-Acid Batteries ....................... 19
SECTION 8 Installation ................................................. 30
SECTION 9 Operation ...................................................45
SECTION 10 Protections ............................................. 47
SECTION 11 Troubleshooting Guide ........................... 50
SECTION 12 Specications ......................................... 52
SECTION 13 Warranty ..................................................54
Disclaimer of Liability
UNLESS SPECIFICALLY AGREED TO IN WRITING, SAMLEX AMERICA INC.:
1. MAKES NO WARRANTY AS TO THE ACCURACY, SUFFICIENCY OR SUITABILITY OF ANY TECHNICAL OR OTHER INFORMATION
PROVIDED IN ITS MANUALS OR OTHER DOCUMENTATION.
2. ASSUMES NO RESPONSIBILITY OR LIABILITY FOR LOSSES, DAMAGES, COSTS OR EXPENSES, WHETHER SPECIAL, DIRECT, INDI-
RECT, CONSEQUENTIAL OR INCIDENTAL, WHICH MIGHT ARISE OUT OF THE USE OF SUCH INFORMATION. THE USE OF ANY
SUCH INFORMATION WILL BE ENTIRELY AT THE USERS RISK.
Samlex America reserves the right to revise this document and to periodically make changes to the content
hereof without obligation or organization of such revisions or changes.
Copyright Notice/Notice of Copyright
Copyright © 2018 by Samlex America Inc. All rights reserved. Permission to copy, distribute and /or modify this
document is prohibited without express written permission by Samlex America Inc.
2 | SAMLEX AMERICA INC. SAMLEX AMERICA INC. | 3
SECTION 1 | Safety Instructions
1.1 SAFETY SYMBOLS
The following safety symbols will be used in this manual to highlight safety
and information:
WARNING!
Indicates possibility of physical harm to the user in case of non-compliance.
!
CAUTION!
Indicates possibility of damage to the equipment in case of non-compliance.
i
INFO
Indicates useful supplemental information.
Please read these instructions before installing or operating the unit to prevent personal
injury or damage to the unit.
1.2 SAFETY INSTRUCTIONS - GENERAL
1.2.1 Installation and wiring compliance
• Installation and wiring must comply with the Local and National Electrical Codes and
must be done by a certied electrician.
1.2.2 Preventing electrical shock
• Always connect the grounding connection on the unit to the appropriate grounding
system.
• Disassembly / repair should be carried out by qualied personnel only.
• Disconnect all AC and DC side connections before working on any circuits associated
with the unit. Turning the ON/OFF switch on the unit to OFF position may not entirely
remove dangerous voltages.
• Be careful when touching bare terminals of capacitors. Capacitors may retain high le-
thal voltages even after the power has been removed. Discharge the capacitors before
working on the circuits.
1.2.3 Installation environment
• The inverter should be installed indoor only in a well ventilated, cool, dry
environment.
• Do not expose to moisture, rain, snow or liquids of any type.
• To reduce the risk of overheating and re, do not obstruct the suction and discharge
openings of the cooling fan.
• To ensure proper ventilation, do not install in a low clearance compartment.
4 | SAMLEX AMERICA INC.
SECTION 1 | Safety Instructions
1.2.4 Preventing re and explosion hazards
• Working with the unit may produce arcs or sparks. Thus, the unit should not be used
in areas where there are ammable materials or gases requiring ignition protected
equipment. These areas may include spaces containing gasoline-powered machinery,
fuel tanks, and battery compartments.
1.2.5 Precautions when working with batteries
• Batteries contain very corrosive diluted Sulphuric Acid as electrolyte. Precautions
should be taken to prevent contact with skin, eyes or clothing.
• Batteries generate Hydrogen and Oxygen during charging resulting in evolution of
explosive gas mixture. Care should be taken to ventilate the battery area and follow
the battery manufacturer’s recommendations.
• Never smoke or allow a spark or ame near the batteries.
• Use caution to reduce the risk of dropping a metal tool on the battery. It could spark
or short circuit the battery or other electrical parts and could cause an explosion.
• Remove metal items like rings, bracelets and watches when working with batteries.
The batteries can produce a short circuit current high enough to weld a ring or the
like to metal and thus, cause a severe burn.
• If you need to remove a battery, always remove the ground terminal from the battery
rst. Make sure that all the accessories are off so that you do not cause a spark.
1.3 SAFETY INSTRUCTIONS - INVERTER RELATED
1.3.1 Preventing Paralleling of the AC Output
The AC output of the unit should never be connected directly to an Electrical Breaker
Panel / Load Centre which is also fed from the utility power / generator. Such a direct
connection may result in parallel operation of the different power sources and AC
power from the utility / generator will be fed back into the unit which will instantly
damage the output section of the unit and may also pose a re and safety hazard. If an
Electrical Breaker Panel / Load Center is fed from this unit and this panel is also required
to be fed from additional alternate AC sources, the AC power from all the AC sources
(like the utility / generator / this inverter) should rst be fed to an Automatic / Manual
Selector Switch and the output of the Selector Switch should be connected to the Elec-
trical Breaker Panel / Load Center. Samlex America, Inc. Automatic Transter Switch model
No. STS-30 is recommended for this application.
!
CAUTION!
To prevent possibility of paralleling and severe damage to the unit, never use a
simple jumper cable with a male plug on both ends to connect the AC output
of the unit to a handy wall receptacle in the home / RV.
4 | SAMLEX AMERICA INC. SAMLEX AMERICA INC. | 5
SECTION 1 | Safety Instructions
1.3.2 Preventing DC Input Over Voltage
It is to be ensured that the DC input voltage of this unit does not exceed 16.5 VDC to
prevent permanent damage to the unit. Please observe the following precautions:
• Ensure that the maximum charging voltage of the external battery charger / alterna-
tor / solar charge controller does not exceed 16.5 VDC.
• Do not connect this unit to a battery system with a voltage higher than the rated 12V
nominal battery input voltage of the unit.
1.3.3 Preventing Reverse Polarity on the Input Side
When making battery connections on the input side, make sure that the polarity of bat-
tery connections is correct (Connect the Positive of the battery to the Positive terminal
of the unit and the Negative of the battery to the Negative terminal of the unit). If the
input is connected in reverse polarity, DC fuse(s) inside the inverter will blow and may
also cause permanent damage to the inverter.
!
CAUTION!
Damage caused by reverse polarity is not covered by warranty.
1.3.4 Use of External Fuse in DC input Circuit
Use Class-T or equivalent fuse of appropriate capacity within 7" of the battery Positive ter-
minal. This fuse is required to protect DC input cable run from damage due to short circuit
along the length of the cable. Please read instructions under Section 8 - Installation.
1.4 LES SYMBOLES DE SÉCURITÉ
Les symboles de sécurité suivants seront utilisés dans ce manuel pour souligner les
informations liées à la sécurité lors de l’installation et de l’utilisation :
MISE EN GARDE!
L'utilisateur pourrait se blesser si les consignes de sécurité ne sont pas suivies.
!
ATTENTION!
Il y a un risque de faire des dégâts à l'équipement lorsque l'utilisateur ne
suit pas les instructions.
i
INFO
Indication de l'info supplémentaire qui pourrait être utiles.
Veuillez lire ces instructions avant d'installer ou de faire fonctionner l'appareil an
de prévenir des blessures corporelles ou des dégâts à l'appareil.
6 | SAMLEX AMERICA INC.
SECTION 1 | Safety Instructions
1.5 CONSIGNES DE SÉCURITÉ - GÉNÉRALES
1.5.1 Installation et Conformité du Câblage
L’installation et le câblage doivent conformer aux Normes Électriques Locales et
Nationales; l’installation doit être faite par un(e) électricien(ne) CERTIFIÉ(E).
1.5.2 Prévention des Décharges Électriques
Connectez toujours la connexion de terre de l'appareil au système de terre approprié.
Seulement une personne qualiée devrait réparer ou désassembler cet appareil.
Débranchez tous les raccordements latéraux d'entrée et de sortie avant de travailler
sur n'importe quel circuit associé au contrôleur de charge. Même si l'interrupteur
«ON/ OFF» est dans la position «off», il pourrait rester des tensions dangereuses.
Faites attention de ne pas toucher les bornes nues des condensateurs. Elles
pourraient retenir des tensions mortelles, même quand une puissance a été
enlevée. Déchargez les condensateurs avant de travailler sur les circuits.
1.5.3 Lieu d'Installation
Il faut situer l'onduleur à l'intérieur dans un endroit bien frais, sec, et ventilé.
Ne pas exposez à l'humidité, la pluie, la neige ou à toutes liquides.
An de réduire les risques de la surchauffe ou d'un incendie, ne bloquez pas les
ouvertures d'admission et d'échappement pour les ventilateurs de refroidissement.
Pour assurer une bonne ventilation, n'installez pas l'appareil dans un comparti-
ment avec peu d’espace.
1.5.4 Prévention des Risques d’Incendie et d'Explosion
L'utilisation de l'appareil pourrait produire des arcs électriques ou des étincelles.
Par conséquent, il ne devrait pas être utilisé dans les endroits où il y a des maté-
riaux ou gaz nécessitant des équipements ignifuges, par exemple, des espaces
contenant des machines alimentées par essence, des réservoirs d'essence ou, des
compartiments à batterie.
1.5.5 Précautions à Prendre en Travaillant avec des Batteries
Les batteries contiennent de l’acide sulfurique, électrolyte corrosif. Certains
précautions doivent être prises an d’empêcher tout contact avec la peau, les
yeux ou les vêtements.
Lorsque les batteries sont rechargées, elle produisent de l'oxygène et de
l'hydrogène, ceci émet un mélange de gaz explosif. Ventilez à fond la zone
de la batterie et, suivez les recommandations du fabricant pour l'emploi de la
batterie.
Ne jamais fumer ni mettre une amme à proximité des batteries.
Soyez prudent, réduisez toute risque de chute d'objets métalliques sur la bat-
terie, ce qui pourrait provoquer des étincelles, ou court-circuiter la batterie et
les autres pièces électriques, et causer une explosion.
Retirez tous vos objets métalliques: bagues, bracelets, montres, etc. lorsque vous
travaillez avec les batteries. Les batteries pourraient produire un court-circuit
assez puissant pour souder des objets causant une brûlure grave.
Si vous devez enlever la batterie, retirez toujours la borne négative (de terre) de
la batterie en premier. Assurez que tous les accessoires soient éteints, pour ne
pas provoquer des étincelles.
6 | SAMLEX AMERICA INC. SAMLEX AMERICA INC. | 7
SECTION 1 | Safety Instructions
1.6 CONSIGNES DE SÉCURITÉ - POUR L'ONDULEUR
1.6.1 Empêcher la Sortie CA de Se Mettre en Parallèle
La sortie CA de l'appareil ne devrait jamais être branchée directement à un tab-
leau électrique qui est aussi alimenté par la puissance d'un service public / d'un
générateur. Une connexion pareille pourrait résulter dans un fonctionnement
en parallèle de ces derniers et, la puissance CA produite par un service public /
générateur serait alimentée à l'appareil causant des dégats à la section de sortie,
et engendrant une risque d'incendie ou de faire mal. Si le tableau électrique
est alimenté par l'appareil et une puissance CA supplémentaire est requise, la
puissance CA des sources comme le service public / générateur / onduleur devrait
être envoyée en premier, à un sélecteur; la sortie du sélecteur devrait être liée
au tableau électrique. Samlex Amérique, Inc. modèle de commutateur transter
automatique n ° STS-30 est recommandé pour cette application.
!
ATTENTION!
An de d'éviter la possibilité que l'appareil se met en parallèle ou devient
fortement endommagé, n'utilisez pas un câble de raccordement pour lier la
sortie CA de l'appareil à un réceptacle mural commode dans la maison/le VR.
1.6.2 Prévention d'une Surtension de l'Entrée CC
II faut assurer que la tension d'entrée CC de cet appareil n'excede pas une tension de 16,5 VCC
affin d'empêcher des dégâts permanents à l'appareil. Veuillez suivre les consignes suivantes:
Assurez que la tension de chargement maximale du chargeur de batterie/
l'alternateur/ contrôleur de charge externe n'excède pas une tension de 16,5 VCC.
Ne pas connecter cet appareil à un système de batterie avec une tension supérieure à
12 V de la batterie nominale de tension d'entrée de l'unité.
1.6.3 Prévention de Polarités Inversées sur le Côté d'Entrée
Quand vous faites des connexions à la batterie du côté d'entrée, veuillez assurer
que les polarités sont mises du bon côté (Liez le Positif de la batterie à la borne
Positive de l'appareil et le Négatif de la batterie à la borne Négative de l'appareil).
Si les polarités de l'entrée sont mises à l'envers, le(s) fusible(s) CC dans l'onduleur
va s'exploser et pourrait causer des dégâts permanents à l'onduleur.
!
ATTENTION!
Des dégâts causés par un inversement des polarités ne sont pas couverts
par la garantie.
1.6.4 L'utilisation de fusible externe dans le circuit d'entrée CC
Utilisez Classe-T ou le fusible équivalent de capacités appropriées dans les 7 pouces
de la borne positive de la batterie. Ce fusible est nécessaire pour protéger le câble
CC d'entrée des dommages dus à un court-circuit le long de la longueur du câble.
S’il vous plaît lisez les instructions vertu de l'article 8 -. Installation.
8 | SAMLEX AMERICA INC.
SECTION 2 | General Information
2.1 DEFINITIONS
The following denitions are used in this manual for explaining various electrical
concepts, specications and operations:
Peak Value: It is the maximum value of electrical parameter like voltage / current.
RMS (Root Mean Square) Value: It is a statistical average value of a quantity that varies
in value with respect to time. For example, a pure sine wave that alternates between
peak values of Positive 169.68V and Negative 169.68V has an RMS value of 120 VAC.
Also, for a pure sine wave, the RMS value = Peak value ÷ 1.414.
Voltage (V), Volts: It is denoted by “V” and the unit is “Volts”. It is the electrical force
that drives electrical current (I) when connected to a load. It can be DC (Direct Current
– ow in one direction only) or AC (Alternating Current – direction of ow changes peri-
odically). The AC value shown in the specications is the RMS (Root Mean Square) value.
Current (I), Amps, A: It is denoted by “I” and the unit is Amperes – shown as “A”. It is
the ow of electrons through a conductor when a voltage (V) is applied across it.
Frequency (F), Hz: It is a measure of the number of occurrences of a repeating event per
unit time. For example, cycles per second (or Hertz) in a sinusoidal voltage.
Efciency, (
η): This is the ratio of Power Output ÷ Power Input.
Phase Angle, (φ): It is denoted by “φ” and species the angle in degrees by which the
current vector leads or lags the voltage vector in a sinusoidal voltage. In a purely induc-
tive load, the current vector lags the voltage vector by Phase Angle (φ) = 90°. In a purely
capacitive load, the current vector leads the voltage vector by Phase Angle, (φ) = 90°. In
a purely resistive load, the current vector is in phase with the voltage vector and hence,
the Phase Angle, (φ) = 0°. In a load consisting of a combination of resistances, induct-
ances and capacitances, the Phase Angle (φ) of the net current vector will be > 0° < 90°
and may lag or lead the voltage vector.
Resistance (R), Ohm, Ω: It is the property of a conductor that opposes the ow of cur-
rent when a voltage is applied across it. In a resistance, the current is in phase with the
voltage. It is denoted by "R" and its unit is "Ohm" - also denoted as "Ω".
Inductive Reactance (X
L
), Capacitive Reactance (X
C
) and Reactance (X): Reactance is the
opposition of a circuit element to a change of electric current or voltage due to that
element's inductance or capacitance. Inductive Reactance (X
L
) is the property of a coil
of wire in resisting any change of electric current through the coil. It is proportional to
frequency and inductance and causes the current vector to lag the voltage vector by
Phase Angle (φ) = 90°. Capacitive reactance (X
C
) is the property of capacitive elements to
oppose changes in voltage. X
C
is inversely proportional to the frequency and capacitance
and causes the current vector to lead the voltage vector by Phase Angle (φ) = 90°. The
unit of both X
L
and X
C
is "Ohm" - also denoted as "Ω". The effects of inductive reac-
8 | SAMLEX AMERICA INC. SAMLEX AMERICA INC. | 9
SECTION 2 | General Information
tance X
L
to cause the current to lag the voltage by 90° and that of the capacitive reac-
tance X
C
to cause the current to lead the voltage by 90° are exactly opposite and the net
effect is a tendency to cancel each other. Hence, in a circuit containing both inductances
and capacitances, the net Reactance (X) will be equal to the difference between the
values of the inductive and capacitive reactances. The net Reactance (X) will be inductive
if X
L
> X
C
and capacitive if X
C
> X
L
.
Impedance, Z: It is the vectorial sum of Resistance and Reactance vectors in a circuit.
Active Power (P), Watts: It is denoted as “P” and the unit is “Watt”. It is the power that
is consumed in the resistive elements of the load. A load will require additional Reactive
Power for powering the inductive and capacitive elements. The effective power required
would be the Apparent Power that is a vectorial sum of the Active and Reactive Powers.
Reactive Power (Q), VAR: Is denoted as “Q” and the unit is VAR. Over a cycle, this power
is alternatively stored and returned by the inductive and capacitive elements of the load.
It is not consumed by the inductive and capacitive elements in the load but a certain
value travels from the AC source to these elements in the (+) half cycle of the sinusoidal
voltage (Positive value) and the same value is returned back to the AC source in the (-)
half cycle of the sinusoidal voltage (Negative value). Hence, when averaged over a span
of one cycle, the net value of this power is 0. However, on an instantaneous basis, this
power has to be provided by the AC source. Hence, the inverter, AC wiring and over cur-
rent protection devices have to be sized based on the combined effect of the Active and
Reactive Powers that is called the Apparent Power.
Apparent (S) Power, VA: This power, denoted by "S", is the vectorial sum of the Active
Power in Watts and the Reactive Power in “VAR”. In magnitude, it is equal to the RMS
value of voltage “V” X the RMS value of current “A”. The Unit is VA. Please note that
Apparent Power VA is more than the Active Power in Watts. Hence, the inverter, AC wir-
ing and over current protection devices have to be sized based on the Apparent Power.
Power Factor, (PF): It is denoted by “PF” and is equal to the ratio of the Active Power
(P) in Watts to the Apparent Power (S) in VA. The maximum value is 1 for resistive types
of loads where the Active Power (P) in Watts = the Apparent Power (S) in VA. It is 0 for
purely inductive or purely capacitive loads. Practically, the loads will be a combination of
resistive, inductive and capacitive elements and hence, its value will be > 0 <1. Normally
it ranges from 0.5 to 0.8.
Load: Electrical appliance or device to which an electrical voltage is fed.
Linear Load: A load that draws sinusoidal current when a sinusoidal voltage is fed to it.
Examples are, incandescent lamp, heater, electric motor, etc.
Non-Linear Load: A load that does not draw a sinusoidal current when a sinusoidal volt-
age is fed to it. For example non-power factor corrected Switched Mode Power Supplies
(SMPS) used in computers, audio video equipment, battery chargers, etc.
10 | SAMLEX AMERICA INC.
Resistive Load: A device or appliance that consists of pure resistance (like lament lamps,
cook tops, toaster, coffee maker etc.) and draws only Active Power (Watts) from the inverter.
The inverter can be sized based on the Active Power rating (Watts) of the Resistive Load
without creating overload (except for resistive loads with Tungsten based heating element
like lament lamps, Quartz/Halogen lamps and Quartz heaters. These require higher start-
ing surge power due to lower resistance value when the heating elements are cold).
Reactive Load: A device or appliance that consists of a combination of resistive, induc-
tive and capacitive elements (like motor driven tools, refrigeration compressors, micro-
waves, computers, audio/ video etc.). These devices require Apparent Power (VA) from
the inverter to operate. The Apparent Power is a vectorial sum of Active Power (Watts)
and Reactive Power (VAR). The inverter has to be sized based on the higher Apparent
Power (VA) and also based on starting surge power.
2.2 OUTPUT VOLTAGE WAVEFORMS
TIME
180
160
140
120
100
80
60
40
20
0
20
40
60
80
100
120
140
160
180
Modified Sine
Wave sits at
ZERO for some
time and then
rises or falls
Modified Sine Wave
Sine Wave
Pure Sine Wave
crosses 0.0V
instantaneously
Fig. 2.1: Pure and Modied Sine Waveforms
The output waveform of the Samlex PST series inverters is a pure sine wave like the
waveform of the grid power. Please see sine wave represented in the Fig. 2.1 that also
shows modied waveform for comparison.
In a sine wave, the voltage rises and falls smoothly with a smoothly changing phase
angle and also changes its polarity instantly when it crosses 0 Volts. In a modied sine
wave, the voltage rises and falls abruptly, the phase angle also changes abruptly and
it sits at 0Vs for some time before changing its polarity. Thus, any device that uses a
control circuitry that senses the phase (for voltage / speed control) or instantaneous zero
voltage crossing (for timing control) will not work properly from a voltage that has a
modied sine waveform.
SECTION 2 | General Information
10 | SAMLEX AMERICA INC. SAMLEX AMERICA INC. | 11
Also, as the modied sine wave is a form of square wave, it is comprised of multiple
sine waves of odd harmonics (multiples) of the fundamental frequency of the modied
sine wave. For example, a 60 Hz modied sine wave will consist of sine waves with odd
harmonic frequencies of 3rd (180 Hz), 5th (300 Hz), 7th (420 Hz) and so on. The high
frequency harmonic content in a modied sine wave produces enhanced radio interfer-
ence, higher heating effect in inductive loads like microwaves and motor driven devices
like hand tools, refrigeration / air-conditioning compressors, pumps etc. The higher
frequency harmonics also produce overloading effect in low frequency capacitors due to
lowering of their capacitive reactance by the higher harmonic frequencies. These capaci-
tors are used in ballasts for uorescent lighting for Power Factor improvement and in
single-phase induction motors as start and run capacitors. Thus, modied and square
wave inverters may shut down due to overload when powering these devices.
2.3 ADVANTAGES OF PURE SINE WAVE INVERTERS
• The output waveform is a sine wave with very low harmonic distortion and cleaner
power like utility supplied electricity.
• Inductive loads like microwaves, motors, transformers etc. run faster, quieter
and cooler.
• More suitable for powering uorescent lighting xtures containing power factor
improvement capacitors and single phase motors containing start and run capacitors
• Reduces audible and electrical noise in fans, uorescent lights, audio ampliers, TV,
fax and answering machines.
• Does not contribute to the possibility of crashes in computers, weird print outs and
glitches in monitors.
2.4 SOME EXAMPLES OF DEVICES THAT MAY NOT WORK PROPERLY
WITH MODIFIED SINE WAVE AND MAY ALSO GET DAMAGED ARE
GIVEN BELOW:
• Laser printers, photocopiers, and magneto-optical hard drives.
• Built-in clocks in devices such as clock radios, alarm clocks, coffee makers, bread-mak-
ers, VCR, microwave ovens etc. may not keep time correctly.
• Output voltage control devices like dimmers, ceiling fan / motor speed control may
not work properly (dimming / speed control may not function).
• Sewing machines with speed / microprocessor control.
• Transformer-less capacitive input powered devices like (i) Razors, ashlights, night-
lights, smoke detectors etc. (ii) Re-chargers for battery packs used in hand power
tools. These may get damaged. Please check with the manufacturer of these types of
devices for suitability.
• Devices that use radio frequency signals carried by the AC distribution wiring.
• Some new furnaces with microprocessor control / Oil burner primary controls.
SECTION 2 | General Information
12 | SAMLEX AMERICA INC.
SECTION 2 | General Information
• High intensity discharge (HID) lamps like Metal Halide lamps. These may get damaged.
Please check with the manufacturer of these types of devices for suitability.
• Some uorescent lamps / light xtures that have power factor correction capacitors.
The inverter may shut down indicating overload.
2.5 POWER RATING OF THE INVERTERS
The continuous output power rating of the inverter is specied in Active Power in Watts
for resistive types of loads like heating elements, incandescent lamps etc. where Power
Factor (PF) = 1. The Surge Power rating is for < 1 sec.
Non resistive / reactive loads with Power Factor < 1 like motors (PF = 0.4 to 0.8), non
Power Factor corrected electronics (PF = 0.5 to 0.6) etc, will draw higher Apparent Power
in Volt Amps (VA). This Apparent Power is the sum of Active Power in Watts plus Reac-
tive Power in VAR and is = Active Power in Watts ÷ Power Factor. Thus, for such reactive
loads, higher sized inverter is required based on the Apparent Power. Further, all reac-
tive types of loads require higher inrush / starting surge power that may last for
> 1 to 5 sec and subsequent lower running power. If the inverter is not sized adequately
based on the type of AC load, it is likely to shut down or fail prematurely due to
repeated overloading.
i
INFO
The manufacturers’ specication for power rating of the appliances and devices
indicates only the running power required. The surge power required by some
specic types of devices as explained above has to be determined by actual test-
ing or by checking with the manufacturer. This may not be possible in all cases
and hence, can be guessed at best, based on some general rules of thumb.
i
INFO
Les spécications du fabricant pour la puissance nominale des appareils
et dis-positifs indiquent seulement la puissance nécessaire pour les faire
marcher. La surtension requise (comme expliqué au-dessus) est determinée
en faisant un test ou, en demandant au Fabricant. En certains cas, cette
information n'est pas disponible mais il est possible de diviner, en utilisant
quelques règles générales.
Table 2.1 lists some common loads that require high surge power on start up. A “Sizing
Factor” has been recommended against each which is a multiplication factor to be ap-
plied to the rated running Watt rating of the load to arrive at the Continuous Power
Rating of the inverter (Multiply the running Watts of the device/ appliance by the Sizing
Factor to arrive at the Continuous Power Rating of the inverter).
12 | SAMLEX AMERICA INC. SAMLEX AMERICA INC. | 13
SECTION 2 | General Information
TABLE 2.1: INVERTER SIZING FACTOR
Type of Device or Appliance
Inverter
Sizing Factor
(See Note 1)
Air Conditioner / Refrigerator / Freezer (Compressor based) 5
Air Compressor 4
Sump Pump / Well Pump / Submersible Pump 3
Dishwasher / Clothes Washer 3
Microwave (where rated output power is the cooking power) 2
Furnace Fan 3
Industrial Motor 3
Portable Kerosene / Diesel Fuel Heater 3
Circular Saw / Bench Grinder 3
Incandescent / Halogen / Quartz Lamps 3
Ceramic / PTC type of heaters 5
Laser Printer / Other Devices using Quartz Lamps for heating 4
Switch Mode Power Supplies (SMPS): no Power Factor correction 2
Photographic Strobe / Flash Lights 4 (See Note 2)
NOTES:
1 Multiply the Running Active Power Rating {Watts} of the appliance by this Factor to arrive at
the Continuous Power Rating of the inverter for powering this appliance.
2 For photographic strobe / ash unit, the surge power of the inverter should be > 4 times the
Watt Sec rating of photographic strobe / ash unit.
14 | SAMLEX AMERICA INC.
SECTION 3 | Limiting Electro-Magnetic
Interference (EMI)
3.1 EMI AND FCC COMPLIANCE
These inverters contain internal switching devices that generate conducted and radiated
electromagnetic interference (EMI). The EMI is unintentional and cannot be entirely
eliminated. The magnitude of EMI is, however, limited by circuit design to acceptable
levels as per limits laid down in North American FCC Standard FCC Part 15(B), Class B.
These limits are designed to provide reasonable protection against harmful interfer-
ence when the equipment is operated in a residential environment. These inverters can
conduct and radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications.
3.2 REDUCING EMI THROUGH PROPER INSTALLATION
The effects of EMI will also depend upon a number of factors external to the inverter
like proximity of the inverter to the EMI receptors, types and quality of connecting wires
and cables etc. EMI due to factors external to the inverter may be reduced as follows:
3.2.1 EMI due to factors external to the inverter may be reduced as follows:
- Ensure that the inverter is rmly grounded to the ground system of the building or
the vehicle
- Locate the inverter as far away from the EMI receptors like radio, audio and video
devices as possible
- Keep the DC side wires between the battery and the inverter as short as possible.
- Do NOT keep the battery wires far apart. Keep them taped together to reduce
their inductance and induced voltages. This reduces ripple in the battery wires and
improves performance and efciency.
- Shield the DC side wires with metal sheathing / copper foil / braiding:
- Use coaxial shielded cable for all antenna inputs (instead of 300 ohm twin leads)
- Use high quality shielded cables to attach audio and video devices to one another
- Limit operation of other high power loads when operating audio / video equipment
14 | SAMLEX AMERICA INC. SAMLEX AMERICA INC. | 15
SECTION 4 | Powering Direct / Embedded Switch
Mode Power Supplies (SMPS)
4.1 CHARACTERISTICS OF SWITCHED MODE POWER SUPPLIES (SMPS)
Switch Mode Power Supplies (SMPS) are extensively used to convert the incoming AC
power into various voltages like 3.3V, 5V, 12V, 24V etc. that are used to power vari-
ous devices and circuits used in electronic equipment like battery chargers, computers,
audio and video devices, radios etc. SMPS use large capacitors in their input section for
ltration. When the power supply is rst turned on, there is a very large inrush cur-
rent drawn by the power supply as the input capacitors are charged (The capacitors act
almost like a short circuit at the instant the power is turned on). The inrush current at
turn-on is several to tens of times larger than the rated RMS input current and lasts for
a few milliseconds. An example of the input voltage versus input current waveforms is
given in Fig. 4.1. It will be seen that the initial input current pulse just after turn-on is >
15 times larger than the steady state RMS current. The inrush dissipates in around 2 or 3
cycles i.e. in around 33 to 50 milliseconds for 60 Hz sine wave.
Further, due to the presence of high value of input lter capacitors, the current drawn
by an SMPS (With no Power Factor correction) is not sinusoidal but non-linear as shown
in Fig 4.2. The steady state input current of SMPS is a train of non-linear pulses instead
of a sinusoidal wave. These pulses are two to four milliseconds duration each with a very
high Crest Factor of around 3 (Crest Factor = Peak value ÷ RMS value).
Many SMPS units incorporate “Inrush Current Limiting”. The most common method is
the NTC (Negative Temperature Coefcient) resistor. The NTC resistor has a high resist-
ance when cold and a low resistance when hot. The NTC resistor is placed in series with
the input to the power supply. The cold resistance limits the input current as the input
capacitors charge up. The input current heats up the NTC and the resistance drops
during normal operation. However, if the power supply is quickly turned off and back
on, the NTC resistor will be hot so its low resistance state will not prevent an inrush
current event.
The inverter should, therefore, be sized adequately to withstand the high inrush current
and the high Crest Factor of the current drawn by the SMPS. Normally, inverters have
short duration Surge Power Rating of 2 times their Maximum Continuous Power Rating.
Hence, it is recommended that for purposes of sizing the inverter to accommodate
Crest Factor of 3, the Maximum Continuous Power Rating of the inverter should be > 2
times the Maximum Continuous Power Rating of the SMPS. For example, an SMPS rated
at 100 Watts should be powered from an inverter that has Maximum Continuous Power
Rating of > 200 Watts.
16 | SAMLEX AMERICA INC.
SECTION 4 | Powering Direct / Embedded Switch
Mode Power Supplies (SMPS)
Input voltage
Inrush current
Peak inrush
current
Rated steady state
input RMS current
NOTE: Voltage
and current scales
are dierent
Fig 4.1: Inrush current in an SMPS
TIME
Peak Current
RMS Current
Non-linear
Input Current
Pulse
Input Sine
Wave Voltage
Crest Factor = Peak Current = 3
RMS Current
Voltage (+)Voltage (–)
Current (+)Current (–)
NOTE: Voltage
and current scales
are dierent
Fig. 4.2: High Crest Factor of current drawn by SMPS
16 | SAMLEX AMERICA INC. SAMLEX AMERICA INC. | 17
SECTION 5 | Principle of Operation
5.1 GENERAL
This inverter converts 12 VDC battery voltage to AC voltage with an RMS (Root Mean
Square) value of 120 VAC, 60 Hz RMS.
5.2 PURE SINE WAVE OUTPUT WAVEFORM
The waveform of the AC voltage is a pure Sine Waveform that is same as the waveform
of Grid / Utility power (Supplementary information on pure Sine Waveform and its
advantages are discussed in Sections 2.2 to 2.4).
Fig. 5.1 below species the characteristics of 120 VAC, 60 Hz pure Sine Waveform. The
instantaneous value and polarity of the voltage varies cyclically with respect to time. For
example, in one cycle in a 120 VAC, 60 Hz system, it slowly rises in the Positive direction
from 0V to a peak Positive value “Vpeak” = + 169.68V, slowly drops to 0V, changes the
polarity to Negative direction and slowly increases in the Negative direction to a peak
Negative value “Vpeak” = - 169.68V and then slowly drops back to 0V. There are 60 such
cycles in 1 sec. Cycles per second is called the “Frequency” and is also termed “Hertz (Hz)”.
The Time Period of 1 Cycle is 16.66 ms.
TIME
0V
Peak Negative Voltage
- V
PEAK = - 169.68V
V
RMS = 120 VAC
Peak Positive Voltage
+ V
PEAK = + 169.68V
Voltage (+)Voltage (–)
16.66 ms
Fig. 5.1: 120 VAC, 60 Hz Pure Sine Waveform
5.3 PRINCIPLE OF OPERATION
12 VDC to 120 VAC conversion takes place in two stages. In the rst stage, 12 VDC
of the battery is converted to a high voltage DC using high frequency switching and
Pulse Width Modulation (PWM) technique. In the second stage, the high voltage DC is
converted to 120 VAC, 60 Hz sine wave AC again using PWM technique. This is done by
using a special wave shaping technique where the high voltage DC is switched at a high
frequency and the pulse width of this switching is modulated with respect to a refer-
ence sine wave.
18 | SAMLEX AMERICA INC.
6.1 LAYOUT
Layout of the unit is shown in Fig 6.1 below
Fig. 6.1: Layout of PST-1000F-12
Legend
1. Three Position Rocker Switch
• — ON − Push top end to switch ON locally
0 OFF − Center to switch OFF locally
EXT Switch − Push bottom end to enable
switching ON and OFF by external
1-Wire / 2-Wire switching control
(Refer to Section 8.9)
2. Green LED - Power ON
3. Red LED - Overload
4. Red LED - Over Temperature
4A. 3-Way Terminal marked EXT.SW. for ON/OFF switching using external control signals (Refer to Section 8.9)
5. NEMA5-20R GFCI Duplex Outlets
5a. Reset Button
5b. Test Button
5c. Red LED marked “Life End Alarm”
5d. Green LED: AC output ON
6A. Ventilation slots at the bottom for air suction for cooling fan
6B. Cooling Fan Opening for air discharge
7. Grounding Lug: Wire hole diameter: 5/16”
Set screw: • 5/16” x 24 TPI
• 3/8” long ; Slotted Head
8. Negative (-) DC Input Terminal
9. Positive (+) DC Input Terminal
10. Modular Jack for RC-15A Remote Control (optional)
1
10
PST-1000F-12 (Front)
PST-1000F-12 (Back)
2
3
4
4A
ON
OFF
EXT.
S
EXT.SW.
5a 5b
5c
5
5d
120 VAC / 60Hz
6B
7
8
9
6A
Wire hole diameter: 7/16”
Set screw: • 5/16” x 24 TPI
• 1/2” long ; Slotted Head
SECTION 6 | Layout
18 | SAMLEX AMERICA INC. SAMLEX AMERICA INC. | 19
7.1 GENERAL
i
INFO
For complete background information on Lead Acid Batteries and charging
process, please visit www.samlexamerica.com > support > white papers >
White Paper - Batteries, Chargers and Alternators.
Lead-acid batteries can be categorized by the type of application:
1. Automotive service - Starting/Lighting/Ignition (SLI, a.k.a. cranking), and
2. Deep cycle service.
Deep Cycle Lead Acid Batteries of appropriate capacity are recommended for powering
of inverters.
7.2 DEEP CYCLE LEAD ACID BATTERIES
Deep cycle batteries are designed with thick-plate electrodes to serve as primary power
sources, to have a constant discharge rate, to have the capability to be deeply dis-
charged up to 80 % capacity and to repeatedly accept recharging. They are marketed
for use in recreation vehicles (RV), boats and electric golf carts – so they may be referred
to as RV batteries, marine batteries or golf cart batteries. Use Deep Cycle batteries for
powering these inverters.
7.3 RATED CAPACITY SPECIFIED IN AMPERE-HOUR (Ah)
Battery capacity “C” is specied in Ampere-hours (Ah). An Ampere is the unit of measure-
ment for electrical current and is dened as a Coulomb of charge passing through an electri-
cal conductor in one second. The Capacity “C” in Ah relates to the ability of the battery to
provide a constant specied value of discharge current (also called “C-Rate”: See Section 7.6)
over a specied time in hours before the battery reaches a specied discharged terminal
voltage (Also called “End Point Voltage”) at a specied temperature of the electrolyte. As a
benchmark, the automotive battery industry rates batteries at a discharge current or C-Rate
of C/20 Amperes corresponding to 20 Hour discharge period. The rated capacity “C” in Ah
in this case will be the number of Amperes of current the battery can deliver for 20 Hours at
80ºF (26.7ºC) till the voltage drops to 1.75V / Cell. i.e. 10.5V for 12V battery, 21V for 24V bat-
tery and 42V for a 48V battery. For example, a 100 Ah battery will deliver 5A for 20 Hours.
7.4 RATED CAPACITY SPECIFIED IN RESERVE CAPACITY (RC)
Battery capacity may also be expressed as Reserve Capacity (RC) in minutes typically for
automotive SLI (Starting, Lighting and Ignition) batteries. It is the time in minutes a
vehicle can be driven after the charging system fails. This is roughly equivalent to the
conditions after the alternator fails while the vehicle is being driven at night with the
headlights on. The battery alone must supply current to the headlights and the com-
puter/ignition system. The assumed battery load is a constant discharge current of 25A.
SECTION 7 | General Information on
Lead-Acid Batteries
20 | SAMLEX AMERICA INC.
SECTION 7 | General Information on
Lead-Acid Batteries
Reserve capacity is the time in minutes for which the battery can deliver 25 Amperes at
80ºF (26.7ºC) till the voltage drops to 1.75V / Cell i.e. 10.5V for 12V battery, 21V for 24V
battery and 42V for 48V battery.
Approximate relationship between the two units is:
Capacity “C” in Ah = Reserve Capacity in RC minutes x 0.6
7.5 TYPICAL BATTERY SIZES
The Table 7.1 below shows details of some popular battery sizes:
TABLE 7.1: POPULAR BATTERY SIZES
BCI* Group Battery Voltage, V Battery Capacity, Ah
27 / 31 12 105
4D 12 160
8D 12 225
GC2** 6 220
* Battery Council International; ** Golf Cart
7.6 SPECIFYING CHARGING / DISCHARGING CURRENTS: C-RATE
Electrical energy is stored in a cell / battery in the form of DC power. The value of the
stored energy is related to the amount of the active materials pasted on the battery
plates, the surface area of the plates and the amount of electrolyte covering the plates.
As explained above, the amount of stored electrical energy is also called the Capacity of
the battery and is designated by the symbol “C”.
The time in Hours over which the battery is discharged to the “End Point Voltage” for
purposes of specifying Ah capacity depends upon the type of application. Let us denote
this discharge time in hours by “T”. Let us denote the discharge current of the battery
as the “C-Rate”. If the battery delivers a very high discharge current, the battery will be
discharged to the “End Point Voltage” in a shorter period of time. On the other hand,
if the battery delivers a lower discharge current, the battery will be discharged to the
“End Point Voltage” after a longer period of time. Mathematically:
EQUATION 1: Discharge current “C-Rate” = Capacity “C” in Ah ÷ Discharge Time “T”
Table 7.2 below gives some examples of C-Rate specications and applications:
TABLE 7.2: DISCHARGE CURRENT RATES - “C-RATES”
Hours of discharge time “T” till
the “End Point Voltage”
"C-Rate" Discharge Current in Amps =
Capacity "C" in Ah ÷ Discharge Time
"T" in Hrs.
Example of C-Rate
Discharge Currents
for 100 Ah battery
0.5 Hrs. 2C 200A
1 Hrs. 1C 100A
5 Hrs. (Inverter application) C/5 or 0.2C 20A
Table Continues Next Page }
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56

Samlexpower PST-1000F-12 Le manuel du propriétaire

Catégorie
Adaptateurs secteur
Taper
Le manuel du propriétaire

dans d''autres langues