Jenn-Air JUB248RBCX02 Le manuel du propriétaire

JUB248RBCX02
Jenn-Air
Marque
Jenn-Air
Modèle
JUB248RBCX02
Catégorie
Boissons glacées
Taper
Le manuel du propriétaire
JENN-AIR_BEVERAGECENTER/
REFRIGERADORPARABEBIDAS/
Rf:FRIGf:RATEURPOURBOISSONS
Overlay Model/Modelo recubierto/Mod_le _ panneau d(_coratif
i_iiiiiiiiiiiiiiii[__
USE& CAREGUIDE
For questions about features, operation/performance, parts, accessories, or service, call:
1-800-JENNAIR (1-800-536-6247} or visit our website at www.jennair.com.
In Canada, call: 1-800-807-6777, or visit our website at www.jennair.ca.
MANUAL DEUSOY CUIDADO
Si tiene preguntas respecto alas caracteristicas, funcionamiento, rendimiento, partes, accesorios o servicio tecnico, flame al:
1-800-JENNAIR (1-800-536-6247) o visite nuestro sitio web en www.jennair.com,
En Canada, flame al: 1-800-807-6777, o visite nuestro sitio web en www.jennair.ca.
GUIDED'UTILISATIONETD'ENTRETIEN
Au Canada, pour assistance, installation ou service, composez le 1-800-807-6777 ou visitez notre site web & www.jennair.ca,
Table of Contents/indice/Table des matieres ...................................................................................... 2
_]ENN-AIRo
2300281 B / 8336411962110
TABLEOF CONTENTS
BEVERAGE CENTER SAFETY ...................................................... 3
Proper Disposal of Your Old Refrigerated Appliance .................. 3
INSTALLATION INSTRUCTIONS .................................................. 4
Tools and Parts ............................................................................ 4
Custom Overlay Frame ................................................................ 4
Location Requirements ................................................................ 5
Electrical Requirements ............................................................... 5
Unpack the Beverage Center ....................................................... 5
Install Custom Overlay Frame ...................................................... 6
Door Closing ................................................................................. 7
Base Grille .................................................................................... 8
BEVERAGE CENTER USE............................................................. 8
Normal Sounds ............................................................................ 8
Using the Control ......................................................................... 8
Beverage/Wine Racks .................................................................. 9
Stocking the Beverage Center ..................................................... 9
Lighting the Beverage Center ...................................................... 9
BEVERAGE CENTER CARE ........................................................ 10
Cleaning ...................................................................................... 10
Changing the Light Bulb ............................................................. 10
Vacation and Moving Care ......................................................... 10
TROUBLESHOOTING .................................................................. 11
ASSISTANCE OR SERVICE ......................................................... 12
In the U.S.A. and Canada ........................................................... 12
WAR RANTY .................................................................................. 13
INDICE
SEGURIDAD DEL REFRIGERADOR PAPA BEBIDAS .............. 14
C6mo deshacerse adecuadamente
de su aparato refrigerado viejo .................................................. 14
INSTRUCCIONES DE INSTALACION ......................................... 15
Piezas y herramientas ................................................................ 15
Marco recubierto a la medida .................................................... 15
Requisites de ubicaci6n ............................................................. 16
Requisitos electricos .................................................................. 17
Desempaque del refrigerador para bebidas .............................. 17
C6mo instalar el marco recubierto a la medida ........................ 17
C6mo cerrar la puerta ................................................................ 19
Rejilla de la base ........................................................................ 19
USO DEL REFRIGERADOR PAPA BEBIDAS ............................. 20
Sonidos normales ....................................................................... 20
Uso del control ........................................................................... 20
Portabebidas/portabotellas ........................................................ 20
C6mo almacenar en el refrigerador para bebidas ..................... 21
C6mo iluminar el refrigerador para bebidas .............................. 21
CUIBABO BEL REFRIGERABOR PAPA BEBIBAS ................... 22
Limpieza ..................................................................................... 22
C6mo cambiar el foco ................................................................ 23
Cuidado durante las vacaciones y mudanzas ........................... 23
SOLUCION DE PROBLEMAS ...................................................... 24
AYUDA O SERVICIO TI_CNICO ................................................... 25
En EE.UU. y Canada .................................................................. 25
GARANTIA ..................................................................................... 26
TABLEDESMATIERES
S¢:CURIT¢: DU RC:FRIGC:RATEUR POUR BOISSONS .............. 27
Mise au rebut de votre vieil appareil refrig6r6 ........................... 27
INSTRUCTIONS D'INSTALLATION ........................................... 28
Outillage et pieces ...................................................................... 28
Cadre decoratif personnalise ..................................................... 28
Exigences d'emplacement ......................................................... 29
Specifications electriques .......................................................... 30
Deballage du refrigerateur pour boissons ................................. 30
Installation du cadre decoratif personnalise .............................. 30
Fermeture de la porte ................................................................. 32
Grille de la base .......................................................................... 32
UTILISATION DU RI:!:FRIGI_RATEUR POUR BOISSONS .......... 33
Sons normaux ............................................................................ 33
Utilisation de la commande ....................................................... 33
Grilles pour le remisage des boissons et du vin ........................ 33
Stockage dans le refrigerateur pour boissons ........................... 34
Eclairage du refrigerateur pour boissons ................................... 34
ENTRETIEN DU RC:FRIGC:RATEUR POUR BOISSONS ............ 35
Nettoyage ................................................................................... 35
Changement de I'ampoule d'eclairage ...................................... 35
Precautions a prendre pour les vacances et avant un
demenagement .......................................................................... 36
DI_PANNAGE ................................................................................. 36
ASSISTANCE OU SERVICE ......................................................... 38
Aux Ctats-Unis et au Canada ..................................................... 38
GARANTIE ..................................................................................... 39
BEVERAGECENTERSAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."
These words mean:
You can be killed or seriously injured if you don't immediately
follow instructions.
You can be killed or seriously injured if you don't follow
instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of fire, electric shock, or injury when using your beverage center, follow these basic
precautions:
• Plug into a grounded 3 prong outlet.
• Do not remove ground prong.
• Do not use an adapter.
• Do not use an extension cord.
• Disconnect power before servicing.
• Replace all parts and panels before operating.
• Remove door or drawer(s) from your old refrigerated
appliance.
• Use nonflammable cleaner.
• Keep flammable materials and vapors, such as gasoline,
away from beverage center.
• Use two or more people to move and install beverage
center.
SAVE THESE INSTRUCTIONS
Proper Disposalof YourOld
RefrigeratedAppliance
Suffocation Hazard
Remove door or drawer(e) from your old refrigerated
appliance.
Failure to do so can result in death or brain damage.
IMPORTANT: Child entrapment and suffocation are not problems
of the past. Junked or abandoned beverage centers are still
dangerous - even if they will sit for "just a few days." If you are
getting rid of your old beverage center, please follow these
instructions to help prevent accidents.
Before You Throw Away Your Old Refrigerated Appliance:
• Take off the door.
• Leave the racks and shelves in place so that children may not
easily climb inside.
INSTALLATIONINSTRUCTIONS
TOOLS NEEDED:
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
• Hand drill or electric drill • Scissors
(properly grounded) • Masking tape
• _/2"Brad point doweling
drill bit • Tape measure
• Phillips screwdriver • Petroleum jelly
PARTS NEEDED:
Custom Overlay Frame--See "Overlay Frame--Rear View."
Hardware (Optional)
PARTS SUPPLIED:
• Flat-head screws (8) • Overlay plates (2)
• Round-head screws (8) • Overlay hooks (4)
If you plan to install a custom overlay frame, you will need to
create the frame yourself or consult a qualified cabinetmaker or
carpenter. See dimension drawings for frame specifications.
IMPORTANT:
• The thickness of the overlay frame must be 3/4"(1.91 cm).
• Overlay frame must not weigh more than 10 Ibs (4.54 kg).
• Overlay frames weighing more than recommended may
cause damage to your appliance.
Overlay Frame-- Rear View
Create the custom overlay frame using the dimensions shown.
A
15_6 ''
(3.33 crn)
413/32" 2.95"
(11.2 cm) (7.6 cm)
2.95"
(7.5 era)
(6.4 cm)
23.62"
(60.0 cm)
A. Overlay hook locations
297/8''
(76.66 cm)
Install Overlay Hooks
Using a Phillips screwdriver and eight flat-head screws attach the
overlay hooks to the back of the overlay frame. See "Overlay
Frame-Rear View" for overlay hook locations.
A. Overlay hooks (4)
Door Hinge Holes
• The views of the top and bottom hinge pin hole show a right-
hand hinge. Mirror the image for a left-hand hinge.
• We recommend using a C-Clamp and two pieces of scrap
wood (front and back) to help reinforce the overlay frame
when drilling the hinge pin holes.
Using a V_"Brad point doweling drill bit, drill a _/_"(1.27 cm)
deep hole into the top of the overlay frame for the top hinge
pin as shown.
Top View
Front Surface
Back Surface
A. Radius 5.0
2. Drill a 1/2"(1.27 cm) deep hole in the bottom of the overlay
frame for the bottom hinge pin as shown. _" ,,, ,. , ' '_ '_,
_,+,,,/%_ _ +,J %4 ,,9,
L
(1.35 turn)
Bottom View
(1.2 cm)
I
Front Surface
)-
Back Surface
A. Radius 5.0
Explosion Hazard
Keep flammable materials and vapors, such as
gasoline, away from beverage center,
Failure to do so can result in death, explosion, or fire.
To ensure proper ventilation for your beverage center, allow for a
1/4"(6.35 mm) space on each side and at the top. When installing
your beverage center next to a fixed wall, leave 21/2'' (6,35 cm)
minimum clearance on the hinge side to allow for the door to
swing open.
NOTE: It is recommended that you do not install the beverage
center near an oven, radiator, or other heat source, Do not install
in a location where the temperature will fall below 55 °F (13°C). For
best performance, do not install the beverage center behind a
cabinet door or block the base grille.
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord,
Failure to follow these instructions can result in death,
fire, or electrical shock.
Before you move your beverage center into its final location, it is
important to make sure you have the proper electrical
connection,
Recommended grounding method
A 115 Volt, 60 Hz,, AC only 15- or 20-amp fused, grounded
electrical supply is required, It is recommended that a separate
circuit serving only your beverage center be provided, Use an
outlet that cannot be turned off by a switch. Do not use an
extension cord.
NOTE: Before performing any type of installation, cleaning, or
removing a light bulb, unplug beverage center or disconnect
power.
Excessive Weight Hazard
Use two or more people to move and install
beverage center.
Failure to do so can result in back or other injury.
Remove the Packaging
Remove tape and glue residue from surfaces before turning
on the beverage center. Rub a small amount of liquid dish
soap over the adhesive with your fingers. Wipe with warm
water and dry.
Do not use sharp instruments, rubbing alcohol, flammable
fluids, or abrasive cleaners to remove tape or glue. These
products can damage the surface of your beverage center.
For more information, see "Beverage Center Safety."
• Disposeof/recycleallpackagingmaterials.
WhenMovingYourBeverageCenter:
Yourbeveragecenterisheavy.Whenmovingtheappliance
forservice,besuretoprotectthefloor.Alwayspullthe
appliancestraightoutwhenmovingit.Donotwiggleor
"walk"theappliancewhentryingtomoveit,asfloor
damagecouldoccur.
3.
Open the door. Lift the front of the door up, pulling straight
out to remove as shown.
Clean Before Using
After you remove all of the packaging materials, clean the inside
of your beverage center before using it. See the cleaning
instructions in "Beverage Center Care."
_'_StC;S(.L_S 0__ O_#@t'Csy' s>_,..............,;7
IM PORTANT:
• Create custom overlay frame according to the specifications
in the "Custom Overlay Frame" section.
• Jenn-Air is not responsible for the removal or addition of
molding or decorative panels that would not allow access to
the appliance for service.
Remove the Door
IMPORTANT: Do not remove the grease from the washer, top
spacer or top hinge pin. Be sure to set aside the top hinge, top
spacer and washer for later use.
1. Using a Phillips screwdriver, remove the three screws from
the top hinge. Remove the top hinge.
2.
A. Screws (3)
B. Top hinge
C. Washer
D. Top spacer
E. Door
Remove the three screws from the top spacer. Remove the
top spacer and washer.
Attach the Overlay Frame
NOTE: If the overlay hooks are not installed, see "Custom
Overlay Frame" for overlay hook locations.
1. Position the overlay frame 1/2"(1.27 cm) higher than the door.
Be sure to position the overlay hooks to the pilot holes.
2. Insert the overlay hooks into the top of the holes in the door.
Push against the overlay frame to force the overlay hooks
deeper into the door. Pull the overlay frame straight down to
secure the overlay hooks to the door.
3. Using a Phillips screwdriver, attach the overlay plates to the
bottom of the overlay frame and door as shown.
B C D
A. Overlay frame
B. Door
C. Overlay plates (2)
D. Round-head screws (8)
Install the Door
IMPORTANT: To ensure proper operation, be sure to grease the
top hinge, top spacer and washer with petroleum jelly.
1. Using a Phillips screwdriver and three screws, attach the top
spacer to the door.
2. Using petroleum jelly, grease the bottom spacer hole and the
bottom hinge pin. Align the washer with the bottom spacer
hole.
3. Slowly lower the door straight and evenly onto the bottom
hinge pin. Be sure the washer stays in place. Close the door.
Be sure the door properly aligns to the cabinet.
NOTE: Provide additional support for the door when moving
the hinges. Do not depend on the door magnets to hold the
door in place while you are working.
4. Using masking tape, secure the door to the cabinet before
installing the top spacer as shown.
7. Remove the masking tape from the door.
Door Closing
Your beverage center has four leveling legs. Ifyour beverage
center seems unsteady or you want the door to close more easily,
adjust the beverage center's tilt using the instructions below.
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord,
Failure to follow these instructions can result in death,
fire, or electrical shock.
1. Plug into a grounded 3 prong outlet.
A. Top spacer
B. Masking tape
5. Place the washer on the top spacer and align the holes.
Grease the top hinge pin, top spacer and washer with
petroleum jelly. Insert the top hinge pin into the washer and
top spacer.
6. Using a Phillips screwdriver and three screws, attach the top
hinge to the cabinet as shown.
A
A
C
1 ,I...............................i
A. Screws (3) D. Top spacer
B. Top Hinge E. Door
C. Washer F Overlay frame
2.
3.
4=
Excessive Weight Hazard
Use two or more people to move and install
beverage center.
Failure to do so can result in back or other injury.
Move the beverage center into its final location.
Turn the leveling legs to the right to lower the beverage center
or turn the leveling legs to the left to raise it. It may take
several turns of the leveling legs to adjust the tilt of the
beverage center.
NOTE: Having someone push against the top of the beverage
center takes some weight off the leveling legs. This makes it
easier to adjust the leveling legs.
Open the door and check to make sure that it closes as easily
as you like. If not, tilt the beverage center slightly more to the
rear by turning both front leveling screws to the right. It may
take several more turns, and you should turn both leveling
legs the same amount.
Remove the Base Grille
1=
2.
Open the beverage center door.
Using a Phillips screwdriver, remove the two screws. Push
both tabs in toward the center to release the base grille from
the beverage center.
/.............................................
r_ ...............; ¢
A B A
A. Tabs
B. Screws
3. Remove the base grille.
Replace the Base Grille
1. Open the beverage center door.
2. Position the base grille so that both tabs align and the base
grille snaps into place. Replace the two screws. Tighten the
screws.
BEVERAGECENTERUSE
Your new beverage center may make sounds that your old one
didn't make. Because the sounds are new to you, you might be
concerned about them. Most of the new sounds are normal. Hard
surfaces, such as the flooring and surrounding structures, can
make the sounds seem louder. The following describes the kinds
of sounds and what may be making them.
• Your beverage center is designed to run more efficiently to
keep your food items at the desired temperatures and to
minimize energy usage. The high efficiency compressor and
fans may cause your beverage center to run longer than your
old one. You may also hear a pulsating or high-pitched sound
from the compressor or fans adjusting to optimize
performance.
• Rattling noises may come from the flow of refrigerant or items
stored inside the beverage center.
• As each cycle ends, you may hear a gurgling sound due to
the refrigerant flowing in your beverage center.
• You may hear water running into the drain pan when the
beverage center is defrosting.
• You may hear clicking sounds when the beverage center
starts or stops running.
For your convenience, your beverage center control is preset at
the factory. When you first install your beverage center, make
sure that the control is still preset to the mid-setting as shown.
Adjusting Controls
The mid-setting indicated in the previous section should be
correct for normal usage. The control is set correctly when
beverages are as cold as you like.
If you need to adjust the temperature, wait at least 24 hours
between adjustments and then recheck the temperature.
Tomake the beverage center colder, adjust the control to the next
higher setting. To make the beverage center less cold, adjust the
control to the next lower setting.
Temperature Separator (Temperature Display)
The temperature separator displays the current temperatures
(Fahrenheit or Celsius) for the upper, middle and lower zones
(compartments) of the beverage center. To adjust the
temperature settings, see "Adjusting Controls" earlier in this
section.
Uppe, Middle
.!--!.
A B C D
A. Dimmer
B. Upper zone display
C. Middle zone display
D. Lower zone display
E.Fahrenheit/Celsius
E
To Remove and Replace the Racks
1. Pull the rack forward until it stops. Push in on the tabs to
release the rack. Continue pulling the rack forward and lift it
up and out of the rack supports.
A
..... e 'c ge C
"._"_,,,*"'--",_ s,sj ..... V ._, ey_
NOTE: For optimum beverage and wine storage, place white
wines at the top of the beverage center in the wine rack. Place
red wines at the bottom.
To Stock the Beverage Center
1. Start stocking the beverage center with the bottom display
rack.
2. Starting on the left-hand side, place the first bottle of wine on
the bottom of the rack with the neck of the bottle facing the
back of the beverage center.
3. Place the next bottle on its side with the neck of the bottle
facing the front of the beverage center.
2.
A
A. Tabs
Replace the rack by inserting the rack into the supports and
sliding it toward the rear of the beverage center.
\
To Remove and Replace the Bottom Rack
1. Liftthe rack (front and back) up and pull straight out to
remove.
2. Replace the rack by pushing it straight back and over the
stop. Continue pushing the rack straight back and evenly
until it is in place.
4. Alternate in this manner until the display rack is full.
5. Pull the next rack forward.
6. Starting on the left-hand side, place the first bottle on the
rack with the neck of the bottle facing forward.
7. Place the next bottle on the shelf with the neck of the bottle
facing the rear of the beverage center.
8. Continue alternating in this manner until the rack is full.
9. Slide the rack into place and continue stocking each
remaining rack as described above.
10. Place juices, sodas or other canned beverages on the glass
shelves.
\
The beverage center has an interior light that comes on any time
the door is opened. You may also turn the light on at any time by
opening the door and pressing the exterior switch located beside
the temperature control knob on the base grille.
NOTE: Leaving the light on for an extended period of time will
slightly increase the temperature of the beverage center.
BEVERAGECENTERCARE
Explosion Hazard
Use nonflammable cleaner.
Failure to do so can result in death, explosion, or fire.
Clean the beverage center about once a month to avoid build-up
of odors. Wipe up spills immediately.
To clean your beverage center:
1. Unplug beverage center or disconnect power.
2. Remove all racks and shelves from inside the beverage
center.
3. Hand wash, rinse, and dry removable parts and interior
surfaces thoroughly. Use a clean sponge or soft cloth and a
mild detergent in warm water.
• To protect wood trim pieces, do not immerse the entire
rack into water when cleaning.
• Do not use abrasive or harsh cleaners such as window
sprays, scouring cleansers, flammable fluids, cleaning
waxes, concentrated detergents, bleaches or cleansers
containing petroleum products on plastic parts, interior
and door liners or gaskets. Do not use paper towels,
scouring pads, or other harsh cleaning tools. These can
scratch or damage materials.
• To help remove odors, you can wash interior walls with a
mixture of warm water and baking soda (2 tbs to 1 qt
[26 g to 0.95 L] of water).
4. Wash stainless steel and painted metal exteriors with a clean
sponge or soft cloth and a mild detergent in warm water. Do
not use abrasive or harsh cleaners, or cleaners containing
chlorine. These can scratch or damage materials. Dry
thoroughly with a soft cloth. For additional protection against
damage to painted metal exteriors, apply appliance wax (or
auto paste wax) with a clean, soft cloth. Do not wax plastic
parts.
NOTE: To keep your stainless steel beverage center looking
like new and to remove minor scuffs or marks, it is suggested
that you use the manufacturer's approved Stainless Steel
Cleaner & Polish. To order the cleaner, see "Accessories."
IMPORTANT: This cleaner is for stainless steel parts only!
Do not allow the Stainless Steel Cleaner & Polish to come into
contact with any plastic parts such as the trim pieces,
dispenser covers or door gaskets. If accidental contact does
occur, clean plastic part with a sponge and mild detergent in
warm water. Dry thoroughly with a soft cloth.
5. Replace the racks and shelves.
6. Clean the condenser coils regularly. They are located behind
the base grille. Coils may need to be cleaned as often as
every other month. This may help save energy.
• Remove the base grille. See "Base Grille."
• Use a vacuum cleaner with an extended attachment to
clean the condenser coils when they are dusty or dirty.
• Replace the base grille.
7. Plug in beverage center or reconnect power.
NOTE: Not all appliance bulbs will fit your beverage center, Be
sure to replace the bulb with one of the same size, shape, and
wattage.
To change the light bulb:
1. Unplug beverage center or disconnect power.
2. Using a Phillips screwdriver, remove the screw located at the
back of the light shield. Pull the light shield back to remove
the tabs from the appliance. Remove the light shield.
A. Light shield
B. Tabs
C. Screw
3. Replace the bulb.
4. Reinstall the light shield by inserting the tabs. Align the holes
and insert the screw. Tighten the screw.
5. Plug in beverage center or reconnect power.
Vacations
If you choose to turn the beverage center off before you leave,
follow these steps.
1. Remove all wine bottles from the beverage center.
2. Unplug the beverage center.
3. Clean the beverage center. See "Cleaning."
4. Tape a rubber or wood block to the top of the door to prop it
open far enough for air to get in. This stops odor and mold
from building up.
10
Moving
When you are moving your beverage center to a new home,
follow these steps to prepare it for the move.
f. Remove all wine bottles from the beverage center.
2. Unplug the beverage center.
3. Clean, wipe, and dry it thoroughly.
4. Take out all removable parts, wrap them well, and tape them
together so they don't shift and rattle during the move.
5. Tape the doors shut and tape the power cord to the beverage
center.
When you get to your new home, put everything back and refer to
the "Installation Instructions" section for preparation instructions.
TROUBLESHOOTING
Trythe solutions suggested here first in order to avoid the cost of an unnecessary service call.
Your beverage center will not operate
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
is the power supply cord unplugged? Plug into a grounded
3 prong outlet.
Has a household fuse blown, or has a circuit breaker
tripped? Replace the fuse or reset the circuit.
Is the Beverage Center Control turned to the OFF
position? See "Using the Control."
The lights do not work
• Is a light bulb loose in the socket? Unplug beverage center
or disconnect power. Gently remove the bulb and reinsert.
Plug in beverage center or reconnect power.
• Has a light bulb burned out? Replace with an appliance
bulb of the same wattage, size, and shape. See "Changing
the Light Bulb."
The motor seems to run too much
Is the temperature outside hotter than normal? Expect the
motor to run longer under warm conditions. At normal
temperatures, expect your motor to run about 40% to 80% of
the time. Under warmer conditions, expect it to run even
more of the time.
Is the door opened often? Expect the motor to run longer
when this occurs. In order to conserve energy, try to get
everything you need out of the beverage center at once, keep
wine bottles positioned label side up so that they are easy to
find, and close the door as soon as the wine is removed.
• Is the control set correctly for the surrounding
conditions? See "Using the Control."
• is the door closed completely? Push the door firmly shut. If
it will not shut all the way, see "The door will not close
completely" later in this section.
• Are the condenser coils dirty? This obstructs air transfer
and makes the motor work harder. Clean the condenser coils.
See "Cleaning."
Temperature is too warm
Is the door opened often? Be aware that the beverage
center will warm when this occurs. In order to keep the
beverage center cool, try to get everything you need out of
the beverage center at once, keep wine bottles positioned
label side up so that they are easy to find, and close the door
as soon as the wine is removed.
• Is the control set correctly for the surrounding
conditions? See "Using the Control."
• is the base grille blocked? For best performance, do not
install the beverage center behind a cabinet door or block the
base grille.
There is interior moisture buildup
is the door opened often? To avoid humidity buildup, try to
get everything you need out of the beverage center at once,
keep wine bottles positioned label side up so that they are
easy to find, and close the door as soon as the wine is
removed. When the door is opened, humidity from the room
air enters the beverage center. The more often the door is
opened, the faster humidity builds up, especially when the
room itself is very humid.
• Is it humid? It is normal for moisture to build up inside the
beverage center when the air is humid.
• Is the control set correctly for the surrounding
conditions? See "Using the Control."
11
The door isdifficult to open
Explosion Hazard
Use nonflammable cleaner.
Failure to do so can result in death, explosion, or fire.
• Is the gasket dirty or sticky? Clean the gasket and the
surface that it touches. Rub a thin coat of paraffin wax on the
gasket following cleaning.
The door will not close completely
• Are the racks or shelves out of position? Put the racks or
shelves back into their correct positions. See "Beverage
Center Use" for more information.
Explosion Hazard
Use nonflammable cleaner.
Failure to do so can result in death, explosion, or fire.
• Is the gasket sticking? Clean the gasket and the surface
that it touches. Rub a thin coat of paraffin wax on the gasket
following cleaning.
ASSISTANCEORSERVICE
Before calling for assistance or service, please check
"Troubleshooting." It may save you the cost of a service call. If
you still need help, follow the instructions below.
When calling, please know the purchase date and the complete
model and serial number of your appliance. This information will
help us to better respond to your request.
If the problem is not due to one of the items listed in the
"Troubleshooting" section...
Call the dealer from whom your appliance was purchased, or call
Maytag Services, LLC, Jenn-Air Customer Assistance at
f-800-JENNAIR (1-800-536-6247) to locate an authorized
service company. When calling, please know the purchase date
and the complete model and serial number of your appliance. Be
sure to retain proof of purchase to verify warranty status.
If the dealer or service company cannot resolve your problem,
write to:
Maytag Services, LLC
Attn.: CAIR c_Center
P.O. Box 2370
Cleveland, TN 37320-2370
Web address: www.jennair.com
Or call: 1-800-JENNAIR (1-800-536-6247).
U.S. customers using TTY for deaf, hearing impaired or speech
impaired, call: 1-800-688-2080 (Monday - Friday, 8:00 a.m. -
8:00 p.m. Eastern Time).
NOTE: When writing or calling about a service problem, please
include the following information:
1. Your name, address and daytime telephone number.
2. Appliance model number and serial number.
3. Name and address of your dealer or servicer.
4. A clear description of the problem you are having.
5. Proof of purchase (sales receipt).
User's guides, service manuals and parts information are
available from Maytag Services, LLC, Customer Assistance.
If the problem is not due to one of the items listed in the
"Troubleshooting" section...
Call the dealer from whom your appliance was purchased, or call
Whirlpool Canada LP, Customer Interaction Centre at
1-800-807-6777 to locate an authorized service company. When
calling, please know the purchase date and the complete model
and serial number of your appliance. Be sure to retain proof of
purchase to verify warranty status.
If the dealer or service company cannot resolve your problem,
write to:
Whirlpool Canada LP
Customer Interaction Centre
1901 Minnesota Court
Mississauga, ON L5N 3A7
Web address: www.jennair.ca
Or call: 1-800-807-6777,
NOTE: When writing or calling about a service problem, please
include the following information:
1. Your name, address and daytime telephone number.
2. Appliance model number and serial number.
3. Name and address of your dealer or servicer.
4. A clear description of the problem you are having.
5. Proof of purchase (sales receipt).
User's guides, service manuals and parts information are
available from Whirlpool Canada LID,Customer Interaction
Centre.
12
JENN-AIR REFRIGERATORWARRANTY
ONE YEAR LIMITED WARRANTY
For one year from the date of purchase, when this major appliance is operated and maintained according to instructions attached to or
furnished with the product, Jenn-Air brand of Maytag Corporation or Maytag Limited (hereafter "Jenn-Air") will pay for factory specified
replacement parts and repair labor to correct defects in materials or workmanship. Service must be provided by a Jenn-Air designated
service company. This limited warranty applies only when the major appliance is used in the country in which it is purchased.
On models with a water filter: 30 day limited warranty on water filter. For 30 days from the date of purchase, when this filter is operated
and maintained according to instructions attached to or furnished with the product, Jenn-Air will pay for replacement parts to correct
defects in materials and workmanship.
SECOND THROUGH FIFTH YEAR LIMITED WARRANTY ON CAVITY LINER AND SEALED REFRIGERATION SYSTEM PARTS
In the second through fifth years from the date of purchase, when this major appliance is operated and maintained according to
instructions attached to or furnished with the product, Jenn-Air will pay for replacement or repair of the refrigerator/freezer cavity liner
(including labor costs) if the part cracks due to defective materials or workmanship. Also, in the second through fifth years from the date
of purchase, Jenn-Air will pay for factory specified parts and labor to correct defects in materials or workmanship in the sealed
refrigeration system. These parts are: compressor, evaporator, condenser, dryer, and connecting tubing. Service must be provided by a
Jenn-Air designated service company.
ITEMS JENN-AIR WILL NOT PAY FOR
1. Service calls to correct the installation of your major appliance, to instruct you how to use your major appliance, to replace or repair
house fuses or to correct house wiring or plumbing.
2. Service calls to repair or replace appliance light bulbs, air filters or water filters. Those consumable parts are excluded from warranty
coverage.
3. Repairs when your major appliance is used for other than normal, single-family household use.
4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in
accordance with electrical or plumbing codes, or use of products not approved by Jenn-Air.
5. Any food loss due to refrigerator or freezer product failures.
6. Replacement parts or repair labor costs for units operated outside the United States or Canada.
7. Pickup and delivery. This major appliance is designed to be repaired in the home.
8. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.
g. Expenses for travel and transportation for product service in remote locations.
10. The removal and reinstallation of your appliance if it is installed in an inaccessible location or is not installed in accordance with
published installation instructions.
11. Replacement parts or repair labor costs when the major appliance is use in a country other than the country in which it was
purchased.
DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES
CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED
HEREIN. IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE,
ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. JENN-AIR SHALL NOT BE LIABLE FOR INCIDENTAL
OR CONSEQUENTIAL DAMAGES. SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF
INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS, SO THESE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES
YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH VARY FROM STATETO STATE OR PROVINCE
TO PROVINCE.
Outside the 50 United States and Canada, this warranty does not apply. Contact your authorized Jenn-Air dealer to determine if another
warranty applies.
If you need service, first see the "Troubleshooting" section of the Use & Care Guide. After checking "Troubleshooting," additional help
can be found by checking the "Assistance or Service" section or by calling Jenn-Air. In the U.S.A., call 1-800-JENNAIR
(1-800-536-6247}. In Canada, call 1-800-807-6777. 2/07
Keep this book and your sales slip together for future
reference. You must provide proof of purchase or installation
date for in-warranty service.
Write down the following information about your major appliance
to better help you obtain assistance or service if you ever need it.
You will need to know your complete model number and serial
number. You can find this information on the model and serial
number label located on the product.
Dealer name
Address
Phone number
Model number
Serial number
Purchase date
13
SEGURIDADDELREFRIGERADORPARABEBIDAS
Su seguridad y la seguridad de los demas es muy importante.
Hemos incluido muchos mensajes importantes de seguridad en este manual yen su electrodomestico. Lea y obedezca siempre
todos los mensajes de seguridad.
Este es el simbolo de advertencia de seguridad.
Este sfmbolo le llama la atenci6n sobre peligros potenciales que pueden ocasionar la muerte o una lesi6n a
usted y a los demas.
Todos los mensajes de seguridad iran a continuaci6n del simbolo de advertencia de seguridad y de la palabra
"PELIGRO" o "ADVERTENCIA". Estas palabras significan:
Si no sigue las instrucciones de inmediato, usted puede
morir o sufrir una lesibn grave.
Si no sigue las instrucciones, usted puede morir o sufrir
una lesi6n grave.
Todos los mensajes de seguridad le diran el peligro potencial, le diran c6mo reducir las posibilidades de sufrir una lesi6n y Io que
puede suceder si no se siguen las instrucciones.
INSTRUCCIONES IMPORTANTES DE SEGURIDAD
ADVERTENCIA: Para reducir el riesgo de incendio, cheque electrico, o lesiones personales al usar su refrigerador para
bebidas, siga estas precauciones basicas:
• Conecte a un contacto de pared de conexi6n a tierra de
3 terminales.
• No quite la terminal de conexi6n a tierra.
• No use un adaptador.
• No use un cable electrico de extensi6n.
• Desconecte el suministro de energia antes de darle servicio.
• Vuelva a colocar todos los componentes y paneles antes de
hacerlo funcionar.
• Remueva la puerta o el(los) caj6n(cajones) de su aparato
refrigerado viejo.
• Use un limpiador no inflamable.
• Mantenga los materiales y vapores inflamables, tales como
gasolina, alejados del refrigerador para bebidas.
• Use dos o mas personas para mover e instalar el
refrigerador para bebidas.
GUARDE ESTAS INSTRUCCIONES
Cbmo deshacerse adecuadamente de su
aparato refrigeradoviejo
Antes de descartar su viejo aparato refrigerado:
• Saque la puerta.
• Deje las rejillas y los estantes en su lugar asf los niSos no
pueden meterse adentro con facilidad.
Peligro de Asfixia
Remueva la puerta o el(los) cajon(cajones) de su
aparato refrigerado viejo.
No seguir esta instrucci6n puede ocasionar la muerte
o daSo al cerebro.
IMPORTANTE: El atrapamiento y asfixia de niSos no es un
problema del pasado. Los refrigeradores para bebidas tirados y
abandonados son un peligro, ann si van a quedar ahi "por unos
pocos dfas". Si Ud. esta por deshacerse de su refrigerador para
bebidas viejo, por favor siga las instrucciones que se dan a
continuaci6n para prevenir accidentes.
14
INSTRUCCIONESDEINSTALACION
F_@;£O_+"+ _,,,+,_+y- _+_,_,,,+,+,,,
HERRAMIENTAS NECESARIAS:
ReQna las herramientas y piezas necesarias antes de comenzar
la instalaci6n.
Lea y siga las instrucciones provistas con cualquiera de las
herramientas enlistadas aqui.
• Taladro manual o • Tijeras
electrico (debidamente
conectado a tierra) • Cinta adhesiva protectora
• Cinta para medir
• Broca de barrena con
punta para cabillas de 1/2" • Petrolato
• Destornillador Phillips
PIEZAS NECESARIAS:
Marco recubierto a la medida - Vea "Marco recubierto - Vista
posterior".
Herrajes (opcionales)
PIEZAS SUMINISTRADAS:
• Tornillos de cabeza • Placas recubiertas (2)
plana (8) • Ganchos recubiertos (4)
• Tornillos de cabeza
redonda (8)
Siva a instalar un marco recubierto a la medlda, debera hacerlo
usted mlsmo o consultar con un carplntero o fabrlcante de
gabinetes callficado. Para obtener informaci6n acerca de las
especlficaciones del marco, yea los graficos dlmensionales.
IM PORTANIE:
• El grosor del marco recubierto debe ser de %" (1,91 cm).
• El marco recubierto no debe pesar mas de 10 Ibs
(4,54 kg).
• Los marcos recubiertos que pesan mas de Io
recomendado pueden dar_ar su electrodomestico.
Marco recubierto - Vista posterior
Cree su marco recubierto a la medida utilizando las medidas que
se muestran.
b 413_2 '' 2,95"
(11,2 crn) (7,5 crn)
lS/16,,
(3,33 cm) V_I,
/
2,95"
A (7,5 cm)
15_6 .
(3,33 cm)
.i
(6,4 cm)
23,62"
(60,0 cm)
A. Ubicaciones de los
ganchos recubiertos
297_''
(75,88 crn)
Cbmo instalar los ganchos recubiertos
Con un destornillador Phillips y ocho tornillos de cabeza plana
ajuste los ganchos recubiertos a la parte posterior del marco
recubierto. Consulte "Marco recubierto - Vista posterior" para ver
las ubicaciones de los ganchos recubiertos.
A
A. Ganchos recubiertos (4)
15
Orificios de la bisagra de la puerta
• Las vistas del orificio de la espiga de ia bisagra superior e
inferior ilustran una bisagra del lade derecho. Refleje la
imagen para una bisagra del lado izquierdo.
Recomendamos usar una abrazadera en C y dos piezas de
madera de deshecho (adeiante y atras) para ayudar a reforzar
el marco recubierto cuando taladre los orificios de la espiga
de la bisagra.
Con una broca de barrena para cabiilas de 1/2",taladre un
orificio de V2"(1,27 cm) de profundidad en la parte superior
del marco recubierto para la espiga de la bisagra superior,
come se muestra.
Vista superior
Superficie frontal
Superficie trasera
2,
A. Radio de 5,0
Taiadre un orificio de V2"(1,27 cm) de profundidad en la parte
inferior del marco recubierto para la espiga de la bisagra
inferior, como se muestra.
t
17/32" _
(1,35 mm)
Vista inferior
(1,2 cm)
Superficie frontal
i-
Superficie trasera
A. Radio de 5,0
Peligro de Explosion
Mantenga los materiales y vapores inflamables,
tales como gasolina, alejados del refrigerador para
bebidae.
No seguir esta inetruccion puede ocaeionar la muerte,
explosion, o incendio.
Para asegurarse la ventilacidn adecuada del refrigerador para
bebidas, deje un espacio de V4" (6,35 mm) a cada lado y per
encima. Si Ud. instala el refrigerador prdximo a una pared fija,
deje come mfnimo 2V2" (6,35 cm) del lado de la bisagra para
permitir que la puerta abra bien.
NOTA: No se recomienda instalar el refrigerador para bebidas
cerca de un homo, radiador u otra fuente de calor. No instale en
un lugar donde la temperatura puede ser menor de 55°F (13°C).
Para obtener un 6ptimo funcionamiento, no instale el refrigerador
para bebidas detras de la puerta de un armario ni bloquee la
rejilla de la base.
I I II
16
_ i _¸ % _ ,_ _ _/_
Peligro de Cheque Electrico
Conecte a un contacto de pared de conexi6n a tierra de
3 terminales.
No quite la terminal de cone×i6n a tierra.
No use un adaptador.
No use un cable electrice de extensi6n.
No seguir estas instrucciones puede ocasionar
la muerte, incendio o cheque electrico.
Antes de mover el refrigerador para bebidas a su ubicaci6n final,
es importante asegurarse de que tiene la conexi6n electrica
adecuada.
M_todo de conexibn a tierra recomendado
Se requiere una fuente de energia electrica de 115 Voltios,
60 Hz., CA solamente y con fusibles de 15 6 20 amperios,
debidamente conectados a tierra. Se recomienda que use un
circuito separado s61o para su refrigerador para bebidas. Use un
tomacorriente que no se pueda apagar con un interrupter. No use
un cable electrico de extensi6n.
NOTA: Antes de realizar cualquier tipo de instalaci6n, limpieza o
de quitar un foco de luz, desenchufe el refrigerador para bebidas
o desconecte el suministro de energia.
p, s_x:;$'"
• Deshagase de todos los materiales de embalaje o reciclelos.
Cuando mueva su refrigerador para bebidas:
Su refrigerador para bebidas es muy pesado. Cuando mueva
el electrodomestico para darle servicio, proteja el piso. AI
mover el electrodomestico, siempre tire directamente hacia
afuera. No menee el electrodomestico de lado a lado ni Io
haga "caminar" cuando Io trate de mover ya que podrfa
dar_ar el piso.
Limpieza antes del use
Una vez que usted haya quitado todos los materiales de
empaque, limpie el interior de su refrigerador para bebidas antes
de usarlo. Vea las instrucciones de limpieza en "Cuidado del
refrigerador para bebidas".
9}mo n e m txsco ss cube69
(:s med@x
IMPORTANTE:
• Cree un marco recubierto a la medida de acuerdo con las
especificaciones en la secci6n "Marco recubierto a la
medida".
• Jenn-Air no es responsable de la remoci6n o adici6n de
molduras o marcos decorativos que pudieran impedir darle
servicio al electrodomestico.
Cbmo quitar la puerta
IMPORTANTE: No quite la grasa de la arandela, del espaciador
superior o de la espiga de la bisagra superior. AsegQrese de
apartar la bisagra superior, el espaciador superior y la arandela
para su use posterior.
1. Quite con un destornillador Phillips los tres tornillos de la
bisagra superior. Saque la bisagra superior.
Peligro de Peso Excesivo
Use dos o m_s personas para mover e instalar
el refrigerador para bebidas.
No seguir esta instrucci6n puede ocasionar una
lesi6n en la espalda u otro tipo de lesiones.
Cbmo quitar los materiales de empaque
Quite los residuos de cinta y goma de las superficies antes
de encender el refrigerador para bebidas. Frote un poco de
detergente Ifquido para vajillas sobre el adhesivo con los
dedos. Limpie con agua tibia y seque.
No use instrumentos filosos, alcohol para fricciones, Ifquidos
inflamables o productos de limpieza abrasives para eliminar
los restos de cinta o goma. Estos productos pueden da_ar la
superficie de su refrigerador para bebidas. Para obtener mas
informaci6n, vea "Seguridad del refrigerador para bebidas".
A. Tornillos (3)
B. Bisagra superior
C. Arandela
D. Espaciador superior
E. Puerta
B
C
D
17
2. Quite los tres tornillos del espaciador superior. Quite el
espaciador superior y la arandela,
3. Abra la puerta. Levante la parte frontal de la puerta,
empujando directamente hacia fuera para quitarla como se
muestra,
3. Ajuste con un destornillador Phillips las placas recubiertas a
la parte inferior del marco recubierto y de la puerta, como se
muestra,
Cbmo fijar el marco recubierto
NOTA: Si los ganchos recubiertos no estan instalados, consulte
"Marco recubierto a la medida" para ver las ubicaciones de los
ganchos recubiertos.
1. Ubique el marco recubierto 1/2"(1,27 cm) por encima de la
puerta. AsegQrese de ubicar los ganchos recubiertos en los
orificios piloto,
LJ
!J
2=
Inserte los ganchos recubiertos en los orificios superiores de
la puerta. Empuje contra el marco recubierto para forzar los
ganchos recubiertos aQn mas dentro la puerta. Jale el marco
recubierto directamente hacia abajo para asegurar los
ganchos recubiertos en la puerta,
B C D
A. Marco recubierto
B.Puerta
C. Placas recubiertas (2)
D. Tornillos de cabeza redonda (8)
Cbmo instalar la puerta
IMPORTANTE: Para asegurar el funcionamiento adecuado,
asegQrese de engrasar la bisagra superior, el espaciador superior
y la arandela con petrolato.
1. Ajuste el espaciador superior a la puerta con un
destornillador Phillips y tres tornillos.
2. Engrase con petrolato el orificio del espaciador inferior y la
espiga de la bisagra inferior. Alinee la arandela con el orificio
del espaciador inferior.
3. Lentamente baje la puerta en forma derecha y pareja hasta la
espiga de la bisagra inferior. AsegQrese de que la arandela se
mantenga en su lugar. Cierre la puerta. AsegQrese de que la
puerta este correctamente alineada con el gabinete.
NOTA: Provea un soporte adicional para la puerta cuando
mueve las bisagras. No se confie en que los imanes de la
puerta van a sostener la puerta en su lugar mientras trabaja.
4. Asegure la puerta al gabinete con cinta adhesiva protectora
antes de instalar el espaciador superior, como se muestra.
A
5=
A. Espaciador superior
B. Cinta adhesiva protectora
Ubique la arandela en el espaciador superior y alinee los
orificios. Engrase la espiga de la bisagra superior, el
espaciador superior y la arandela con petrolato. Inserte la
espiga de la bisagra superior en la arandela y el espaciador
superior.
18
6.
Ajuste la bisagra superior al gabinete con un destornillador
Phillips y tres tomillos, come se muestra,
Peligro de Peso E×cesivo
Use doe o mas personas para mover e inetalar
el refrigerador para bebidae.
No seguir esta instruccion puede ocaeionar una
lesion en la eepalda u otro tipo de leeionee.
E
F
IIII
A. Tornillos(3) D. Espaciador
B.Bisagra superior superior
C.Arandela E.Puerta
E Marco recubierto
7. Quite la cinta adhesiva protectora de la puerta.
2.
3.
Mueva el refrigerador para bebidas hacia su posici6n final.
Gire las patas niveladoras hacia la derecha para bajar el
refrigerador para bebidas o girelas hacia la izquierda para
levantarlo, Puede precisar darle varias vueltas alas patas
niveladoras para ajustar la inclinaci6n del refrigerador para
bebidas.
NOTA: Para quitar un poco de peso de las patas niveladoras,
haga que alguien empuje la parte superior del refrigerador
para bebidas, Esto facilita el ajuste de las patas niveladoras,
C6mo cerrar la puerta
Su refrigerador para bebidas tiene cuatro patas niveladoras. Si su
refrigerador para bebidas parece inestable ousted quiere que la
puerta se cierre con mayor facilidad, ajuste la inclinaci6n del
refrigerador para bebidas usando las instrucciones a
continuaci6n.
Peligro de Choque Eiectrico
Conecte a un contacto de pared de cone×ion a tierra de
3 terminales.
No quite la terminal de cone×ion a tierra.
No use un adaptador.
No use un cable electrico de extenei6n.
No eeguir eetae instrucciones puede oeaeionar
la muerte, incendio o choque el_ctrico.
Conecte a un contacto de pared de conexi6n a tierra de
3 terminales,
4.
Abra la puerta y verifique para asegurarse de que se cierra
con la facilidad que usted desea. De Io contrario, incline el
refrigerador para bebidas ligeramente mas hacia la parte
posterior, girando ambos tornillos reguladores frontales hacia
la derecha, Puede tomar varias vueltas mas, y usted debera
girar ambas patas niveladoras la misma cantidad de veces.
Quite la rejilla de la base
1. Abra la puerta del refrigerador para bebidas,
2. Saque los dos tornillos con un destornillador Phillips, Empuje
ambas leng0etas hacia el centre para liberar la rejilla de la
base del refrigerador para bebidas.
A B
A. LengOetas
B. Tomillos
3. Quite la rejilla de la base,
Vuelva a colocar la rejilla de la base
1. Abra la puerta del refrigerador para bebidas,
2. Coloque la rejilla de la base de manera que ambas leng0etas
esten alineadas y la rejilla de la base encaje en su lugar.
Vuelva a colocar los dos tornillos. Apriete los tornillos,
19
USODELREFRIGERADORPARABEBIDAS
Su nuevo refrigerador para bebidas puede hacer ruidos que su
viejo refrigerador para bebidas no hac[a. Come estos sonidos
son nuevos para Ud., puede ser que se preocupe. La mayoHa de
los sonidos nuevos son normales. Las superficies duras tales
como el piso y las estructuras circundantes pueden hacer que
los sonidos parezcan mas fuertes. A continuaci6n se describen
los tipos de sonidos y que puede causarlos.
• Su refrigerador para bebidas esta dise_ado para funcionar
con mas eficiencia para conservar sus alimentos a la
temperatura deseada y para reducir al mfnimo el uso de
energia. El compresor y los ventiladores de alta eficiencia
pueden causar que su nuevo refrigerador para bebidas
funcione por periodos de tiempo mas largos que su
refrigerador para bebidas viejo. Tambien puede escuchar un
sonido pulsante o agudo del compresor o los ventiladores
que se ajustan para un funcionamiento 6ptimo.
• Las vibraciones pueden producirse por el flujo de Ifquido
refrigerante o artfculos guardados dentro del refrigerador
para bebidas.
• AI final de cada ciclo, Ud. puede escuchar un gorgoteo
debido al flujo de liquido refrigerante en su refrigerador para
bebidas.
• Ud. puede escuchar agua corriendo hacia la bandeja
recolectora cuando el refrigerador para bebidas se esta
descongelando.
• Es posible que escuche sonidos como de chasquido cuando
el refrigerador para bebidas comienza o deja de funcionar.
Separador de temperatura (Pantalla de temperatura)
El separador de temperatura muestra las temperaturas actuales
(en Fahrenheit o centigrados) para las zonas (compartimientos
superior, media e inferior del refrigerador para bebidas. Para
regular los ajustes de temperatura, vea "C6mo ajustar los
controles" anteriormente en esta secci6n.
Uppe, Middle Lower
i/ i_i
! I_ i _"
,!--i i
I I I I
A B C D E
A. Reductor de luz
B. Pantalla de la zona superior
C. Pantalla de la zona media
D. Pantalla de la zona inferior
E.Fahrenheit/centfgrados
Para quitar y volver a colocar los estantes
1. Jale el estante hacia adelante hasta que se detenga. Empuje
las lengQetas para liberar el estante. ContinQe jalando el
estante hacia delante y levantelo fuera de los soportes del
mismo.
Para su comodidad, el control de su refrigerador para bebidas ha
sido prefijado de fabrica. AI instalar su refrigerador para bebidas
per primera vez, cerci6rese de que el control aQn este prefijado
en el ajuste medio, come se ilustra.
_ Co_de_
OFF__
Coldest
Cbmo ajustar los controles
El ajuste medio indicado en la secci6n previa debe estar correcto
para el uso normal. El control esta fijado correctamente cuando
las bebidas estan tan frias come a usted le gusta.
Si necesita ajustar la temperatura, espere per Io menos 24 horas
entre un ajuste y otro, y despues vuelva a verificar la
temperatura.
Para hacer que el refrigerador para bebidas este mas frio,
coloque el control en el siguiente ajuste mas alto. Para hacer que
el refrigerador para bebidas este menos fHo, coloque el control
en el siguiente ajuste mas bajo.
A
A
A. Leng#e_s
20
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40

Jenn-Air JUB248RBCX02 Le manuel du propriétaire

JUB248RBCX02
Jenn-Air
Marque
Jenn-Air
Modèle
JUB248RBCX02
Catégorie
Boissons glacées
Taper
Le manuel du propriétaire
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents