Kichler Lighting 330174NBR Guide d'installation

INSTRUCTION MANUAL

Product images may vary slightly from actual product.

42"/52" Starkk

™

LED

2 | KICHLER.COM

TABLE OF CONTENTS

SAFETY RULES ..................................................................4

TOOLS REQUIRED ............................................................5

PACKAGE CONTENTS ................................................... 6

MOUNTING OPTIONS .................................................... 6

HANGING THE FAN ..........................................................7

INSTALLATION OF SAFETY SUPPORT ................... 9

ELECTRICAL CONNECTIONS ..................................10

FINISHING THE INSTALLATION................................ 11

ATTACHING THE FAN BLADES .................................12

INSTALLING THE Light PLATE ..................................12

INSTALLING THE LIGHT KIT ....................................... 13

INSTALLING THE GLASS SHADE .............................14

OPERATING INSTRUCTIONS .....................................15

TROUBLESHOOTING....................................................16

FCC INFORMATION ...................................................... 18

42"/52" Starkk

™

LED | 3

4 | KICHLER.COM

1. CAUTION – RISK OF SHOCK –

Disconnect Power at the main circuit breaker

panel or main fusebox before starting and during

the installation.

2. WARNING: This fixture is intended for installation

in accordance with the National Electrical Code

(NEC) and all local code specifications. If you are

not familiar with code requirements, installation by

a certified electrician is recommended.

3. WARNING: To reduce the risk of fire or electric

shock, use only the control provided with the fan.

4. WARNING: To reduce the risk of fire, electric

shock, or Personal Injury, mount directly to a

structural framing member or to an outlet box

marked “Acceptable for Fan Support of 15.9kg

(35 lbs) or less”. For outlet box mounting, use

mounting screws provided with the outlet box.

5. To operate the reverse function on this fan, slide

the reverse switch to the opposite position. Do

not operate reversing switch while fan blades

are in motion. Fan must be turned o and blades

stopped before reversing blade direction.

6. Avoid placing objects in the path of the blades.

7. To avoid personal injury or damage to the fan and

other items, be cautious when working around or

cleaning the fan.

8. Make sure the installation site you choose allows a

minimum clearance of 7 feet from the blades to the floor

and at least 30 inches from the ends of the blades to any

obstruction.

9. Do not use water or detergents when cleaning the fan

or fan blades. A dry dust cloth or lightly dampened cloth

will be suitable for most cleaning.

10. After making the electrical connections, spliced

conductors should be turned upward and pushed

carefully up into outlet box. The wires should be spread

apart with the ground wire and white (common) wire to

one side with the black (load) wire to the other side of

the outlet box.

11. Electrical diagrams are for reference only. Light kits

that are not packed with the fan must be ETL Listed

and marked suitable for use with the model fan you are

installing. Switches must be ETL General Use Switches.

Refer to the Instructions packaged with the light kits

and switches for proper assembly.

WARNING

TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND

THE BLADE BRACKETS (ALSO REFERRED TO AS FLANGES)

DURING ASSEMBLY OR AFTER INSTALLATION. DO NOT INSERT

OBJECTS IN THE PATH OF THE BLADES.

SAFETY RULES

TOOLS AND MATERIALS REQUIRED

Package contents

• Phillips Screwdriver

• Blade Screwdriver

• 11 mm Wrench

• Step Ladder

• Wire Cutters

Unpack your fan and check the contents. You should have the following items:

A. Mounting Bracket

B. Ball / Downrod Assembly (1)

C. Canopy

D. Canopy Trim Ring

E. Coupling Cover

F. Motor Body

G. Blade

H. Light Plate

I. LED Light Kit

J. Glass

K. Fob (2)

L. Mounting Hardware Package

M. Package Contents:

1.) Mounting Connectors (3)

2.) Blade Attachment Hardware:

Blade Screw (15)

Fiber Washer (15)

3.) Safety Cable Hardware:

Wood Screw (1)

Flat Washer (1)

Spring Washer (1)

A

B

C

D

E

F

G

H

I

J

M

K

L

42"/52" Starkk

™

LED | 5

6 | KICHLER.COM

MOUNTING OPTIONS

If there isn’t an existing UL (cUL for Canadian Installation) listed

mounting box, then read the following instructions. Disconnect

the power by removing fuses or turning o circuit breakers.

Secure the outlet box directly to the building structure. Use

appropriate fasteners and building materials. The outlet box

and its support must be able to fully support the full weight of

the fan (up to 50 lbs). Do not use plastic outlet boxes.

Figures 1, 2 and 3 are examples of dierent ways to mount the

outlet box.

NOTE: If you are installing the ceiling fan on a sloped (vaulted)

ceiling, you may need a longer downrod to maintain proper

clearance between the tip of the blade and the ceiling. A

minimum clearance of 12" is suggested for optimal operation.

NOTE: You must use 12" or longer downrod for 30° slope

(max angle 30°). (Fig. 3)

NOTE: Depending on the location you have selected for

installation, you may need to purchase and install a “Joist

Hanger” for the support of the outlet box. Make sure the joist

hanger you purchase has been designed for use with ceiling

fans. (Fig. 4)

Fig. 1

Outlet box

Fig. 2

Fig. 3

Fig. 4

Outlet box

Recessed

outlet box ceiling

mounting

plane

Provide strong

support

ANGLED CEILING

MAXIMUM 30° ANGLE

Fig. 5

Fig. 6

Fig. 7

Outlet Box

Mounting

Bracket

Flat Washer

Screw

Mounting

Bracket

Shoulder

Downrod

Set Screw

Hanger Ball

Cross Pin

HANGING THE FAN

REMEMBER to turn o the power before you begin installation. This is necessary for

your safety and also the proper programming of the control system.

To properly install your ceiling fan, follow the steps below.

Step 1. Before attaching fan to outlet box (not included), ensure the outlet box is securely

fastened to at least two points to a structural ceiling member (a loose box will cause the

fan to wobble). Pass the 120 volt supply wires from the ceiling outlet box through the

center of the ceiling mounting bracket. Install mounting bracket to outlet box in ceiling

using the screws and washers included with the outlet box. (Fig. 5)

Step 2. Remove one of the two shoulder screws in the mounting bracket and save it for

later use. Loosen the second shoulder screw without fully removing it. (Fig. 6)

Step 3. Remove the hanger ball from downrod assembly by loosening set screws,

removing the cross pin, and twisting ball o the rod. ( Fig. 7)

42"/52" Starkk

™

LED | 7

8 | KICHLER.COM

HANGING THE FAN (continued)

Step 4. Loosen the two set screws and remove the clip and cross pin from the top

coupling of the motor body.Carefully feed the fan wires up through the downrod.

Thread the downrod onto the motor coupling until the cross pin holes are aligned.

Next, replace the cross pin and clip, and tighten both set screws. (Fig.8)

Step 5. Slip the coupling cover, canopy trim ring and canopy onto the downrod.

Carefully reinstall the hanger ball onto the downrod. Make sure the cross pin is

in the correct position and the set screws are tight and the wires are not twisted.

(Fig.9)

Step 6. Now lift the motor body into position and place the hanger ball into the

hanger bracket. Rotate until the “Check Tab” has dropped into the “Registration

Slot” and seats firmly. (Fig.10) The entire motor body should not rotate if this is

done correctly.

WARNING: Failure to properly seat the “Check Tab” can damage the ceiling fan

during operation.

Cross Pin

Clip

Set Screw

Cross Pin

Set Screw

Motor Body

Fig. 8

Fig. 9

Fig. 10

Canopy

Hanger Ball

Canopy Trim Ring

Coupling Cover

Motor Body

Mounting

Bracket

Hanger

Ball

Registration Slot

Check Tab

Flat Washer

INSTALLATION OF SAFETY SUPPORT

(required for Canadian installation ONLY)

A safety support cable is provided to help prevent the ceiling fan from faIling, please

install it as follows.

Step 1. Drive a wood screw and washers into the side of the brace that holds the outlet

box. Leave 3mm (1/8") of space between the support brace and the washer. (Fig. 11)

Step 2. Insert the safety cable through the mounting bracket and one of the holes in

the outlet box into the ceiling. Adjust the length of the safety cable to reach the screw

and washers by pulling the extra cable through the cable clamp until the overall length is

correct, put the end of the cable back through the cable clamp, forming a loop at the end

of the cable. Tighten the cable clamp securely. Now, put the loop in the end of the safety

cable over the wood screw and under the washer. Tighten the wood screw securely.

(Fig. 12)

NOTE: Although the safety support cable is required for Canadian installations only.

It’s a good idea to make the attachment with any installation.

Wood Screw

Spring Washer

Outlet Box

Ceiling

Support Brace

Safety Cable

Bolt

Wood Screw

Fig. 12

Fig. 11

42"/52" Starkk

™

LED | 9

10 | KICHLER.COM

ELECTRICAL CONNECTIONS

WARNING: To avoid possible electrical shock, be sure you have turned o the power at

the main circuit panel before wiring.

Follow the steps below to connect the fan to your household wiring. Use the wire

connectors supplied with your fan. Secure the connector with electrical tape. Make sure

there are no loose wire stands or connections.

WARNING: If your house wires are dierent colors than referenced in this manual, stop

immediately. A professional electrician is recommended to determine proper wiring.

Step 1. Connect the fan supply (black) wire and light supply (blue) wire to the black

household supply wire as shown in Figure 13.

Step 2. Connect the neutral fan (white) wire to the neutral household (white) wire.

Step 3. Connect the fan ground wire (green) to the household ground wire.

Step 4. After connecting the wires, spread them apart so that the green and white wires

are on one side of the outlet box and the black wires is on the other side.

NOTE: Carefully tuck the wire connections up into the outlet box.

Vac 120V

Supply Wire

Green ground

Wiring box

Ground to

mounting bracket

and downrod

BLACK

WHITE

BLACK

WHITE

GREEN

BLUE

Fig. 13

FINISHING THE MOTOR INSTALLATION

Step 1. Assemble canopy by rotating key slot in canopy over shoulder screw in

mounting bracket. Tighten shoulder screw. Fully assemble and tighten second

shoulder screw that was previously removed. (Fig. 14)

Step 2. Securely attach and tighten the canopy hole cover over the shoulder

screws in the mounting bracket utilizing the keyslot twist-lock feature. (Fig. 15)

Shoulder Screw

Canopy Hole Cover

Fig. 14

Fig. 15

42"/52" Starkk

™

LED | 11

12 | KICHLER.COM

ATTACHING THE FAN BLADES

NOTE: Before continuing, make sure the power is disconnected by turning o

the circuit breaker of removing the fuse at the circuit box.

Step 1. Slide blades through the blade slots in motor housing and attach to

motor brackets using the screws and blade plates. Make sure the screws

securing the blade to blade bracket are tight and are properly seated. (Fig. 16)

INSTALLING THE LIGHT PLATE

Step 1. Remove the screw marked with a dot label on the mounting plate and

save for later use, and slightly loosen the other two screws. Attach the light

plate to mounting plate using the two key slots in the light plate. Replace the

previously removed screw and securely tighten all 3 screws. (Fig. 17)

Blade Slot

Blade

Blade Washer

Blade Screw

Blade Bracket

Mounting

Plate

Light Plate

Screw

Fig. 16

Fig. 17

INSTALLING THE LIGHT KIT

NOTE: Before continuing installation, confirm that the power is still turned o

at the main circuit breaker or by removing the correct fuse. Turning the power

o using a wall switch is not sucient to prevent electrical shock.

Step 1. Remove one of the three screws in light plate and keep for later use,

slightly loosen the other remaining screws. (Fig. 18)

Step 2. Securely attach the 9-pin connector to the wiring harness socket

within the motor assembly (Fig. 19)

Light Plate

LED Light Kit

Fig. 18

Fig. 19

42"/52" Starkk

™

LED | 13

14 | KICHLER.COM

INSTALLING THE LIGHT KIT (Continued)

Step 3. Assemble the LED light kit assembly to the light plate using the two

key slots in light kit assembly. Replace the previously removed screw and

securely tighten all three screws. (Fig.20)

INSTALLING THE GLASS

Step 1. Secure the glass to light kit assembly and twist clockwise. Do not

over-tighten. (Fig.21)

LED Light Kit

Light Plate

Light Kit

Glass

Fig. 20

Fig. 21

OPERATING INSTRUCTIONS:

Restore power to ceiling fan and test for proper operation. Connect

the decorative fobs to the appropriate pull chains and restore power

to ceiling fan and test for proper operation. (Fig. 22)

1. The pull chain for fan speed control: High, Medium, Low and O.

Pull once for each position.

2. The pull chain kit for light control: ON or OFF.

3. Fan Reverse switch: control direction, forward or reverse.

Do not operate reversing switch while fan blades are in motion.

Fan must be turned o and blades stopped before reversing blade

direction.

Speed setting for warm or cool weather depends on factors such as

the room size, ceiling height, number of fans and so on.

Warm Weather Operation: Forward (counter clockwise). A

downward airflow creates a cooling eect (Fig. 23). This allows you to

set your air conditioner on a warmer setting without aecting your

general comfort.

Cool Weather Operation: Reverse (clockwise). An upward airflow

moves warm air o the ceiling areas (Fig. 24). This allows you to set

your heating unit on a cooler setting without aecting your general

comfort.

Fob

Light Control

Pull Chain

Fan Control

Pull Chain

Reverse Switch

Fig. 22

Fig. 23 Fig. 24

42"/52" Starkk

™

LED | 15

16 | KICHLER.COM

Troubleshooting

Problem Solution

Fan will not start. 1. Check circuit fuses or breakers.

2. Check all electrical connections to ensure proper contact. CAUTION: Make sure the main

power is OFF when checking any electrical connection.

3. Make sure the transmitter batteries are installed properly.

4. Ensure the batteries have a good charge.

Fan sounds noisy. 1. Make sure all motor housing screws are snug.

2. Make sure the screws that attach the fan blade brackets to the motor are tight.

3. Make sure wire nut connections are not rubbing against each other or the interior wall of the

switch housing. CAUTION: Make sure main power is o.

4. Allow a 24-hour “breaking-in” period. Most noise associated with a new fan disappear during

this time.

5. If using an optional light kit, make sure the screws securing the glassware are tight. Make sure

the light bulbs are not touching any other component.

6. Do not connect this fan to wall mounted variable speed control(s). They are not compatible

with ceiling fan motors or remote controls.

7. Make sure the upper canopy is a short distance from the ceiling. It should not touch the ceiling.

Troubleshooting

Problem Solution

Fan wobble. 1. Check that all blade and blade arm screws are secure.

2. Most fan wobbling problems are caused when blade levels are unequal. Check this level by

selecting a point on the ceiling above the tip of one of the blades. Measure this distance. Rotate

the fan until the next blade is positioned for measurement. Repeat for each blade. The distance

deviation should be equal within 1/8".

3. If the blade wobble is still noticeable, interchanging two adjacent (side by side) blades can

redistribute the weight and possibly result in smoother operation.

WARNING: TO REDUCE THE RISK OF PERSONAL INJURY AND TO ENUSRE THE PROPER

OPERATION OF YOUR CEILING FAN. NEVER ATTACH THE BLADE ASSEMBLIES UNTIL THE

CEILING FAN HAS BEEN MOUNTING ON THE CEILING. DO NOT BEND THE BLADE ARMS

WHILE INSTALLING, BALANCING OR CLEANING THE FAN. DO NOT INSERT FOREIGN

OBJECTS BETWEEN ROTATING FAN BLADES.

42"/52" Starkk

™

LED | 17

18 | KICHLER.COM

FCC Information

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1) This device may not cause harmful interference, and

2) This device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by

turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

KICHLER LIGHTING

7711 EAST PLEASANT VALLEY ROAD

CLEVELAND, OHIO 44131

CUSTOMER SERVICE 866.558.5706

8:00 AM TO 5:00 PM EST, MONDAY - FRIDAY

MANUEL D'INSTRUCTIONS

Les images du produit peuvent varier légèrement par rapport au produit réel.

42"/52" Starkk

™

LED

La page charge ...

Kichler Lighting 330174NBR Guide d'installation

Ce manuel convient également à

Kichler Lighting 330174NBR Guide d'installation

dans d''autres langues

Documents connexes

Autres documents