Hangar 9 HAN2765 Le manuel du propriétaire

F6F-5 Hellcat 15cc

Instruction Manual

Bedienungsanleitung

Manuel d’utilisation

Manuale di Istruzioni

2

 SPECIFICATIONS • SPEZIFIKATIONEN • SPÉCIFICATIONS • SPECIFICHE

64.0 in (1628 mm)

698.3 sq in (45.1 dm2) Total/Totale

47.8 in (1213 mm)

9–10 lbs (4.08–4.54 kg)

2-Stroke Gas: 15cc–20cc, 4-Stroke gas/petrol: 20cc

2-Takt Benziner: 15cc–20cc, 4-Takt Benzin: 20 cc

2 temps Essence: 15cc–20cc, 4 temps essence: 20cc

2-Tempi Gas: 15cc–20cc, 4 tempi benzina: 20 cc

Electric Power: Power 60, 470Kv Brushless

Elektro Antrieb Power: Power 60, 470Kv Brushless

Moteur électrique (EP): Power 60, 470Kv Brushless

Motore elettrico: Power 60, 470Kv Brushless

5-channel (or greater) with 5 servos

5-Kanal (oder größer) mit 5-Servos

5 voies (ou plus) avec 5 servos

a 5 canali (o più) con 5 servo

Spinner: 1-inch (Not Included)

Spinner: 25mm (Nicht enthalten)

Cône: 25mm (Non fourni)

Ogiva dell’elica: 25mm (Non inclusa)

5

7

/

8

inches (149mm)

B

A

C

D

E

O

F

G

H

I

J

K

L

M

N

P

Q

R

3

F6F-5 Hellcat 15cc

Part # English Deutsch Français Italiano

 REPLACEMENT PARTS • ERSATZTEILE • PIÈCES DE RECHANGE • PEZZI DI RICAMBIO

A

HAN276501 Fuselage with Hatch Rumpf mit Haube Fuselage avec capot Fusoliera con portello

B

HAN276502 Left-Hand Wing with Aileron Linke Tragﬂ äche mit Querruder Aile gauche avec aileron Ala sinistra con alettone

C

HAN276503 Right-Hand Wing with Aileron Rechte Tragﬂ äche mit Querruder Aile droite avec aileron Ala destra con alettone

D

HAN276504 Stabilizer and Elevator Höhenruderset Set Plan horizontal et Gouverne de profondeur Set stabilizzatore ed elevatore

E

HAN276505 Fin and Rudder Finne u. Seitenruder Dérive et sa gouverne Direzionale e timone

F

HAN276506 Cowling Motorhaube Capot moteur Carenatura

G

HAN276507 Top Hatch Obere Abdeckung Trappe supérieure Portello superiore

H

HAN276508 Canopy Kabinenhaube Verrière Calotta

I

HAN276509 Painted Pilot Lackierter Pilot Pilote peint Pilota verniciato

J

HAN276510 Pushrod Set Gestänge / Anlenkungen Set Jeu de tringleries Set dell’asta di spinta

K

HAN276511 Hardware Set Kleinteile Set Sachet de visserie Set dei pezzi

L HAN276512 Wheels, 3

1

/

2

-inch Räder, 89mm Roues, 89mm Ruote, 89 mm

M

HAN276514 Tailwheel Assembly Spornrad m. Zbh. Assemblage de roulette de queue Gruppo del ruotino di coda

N

HAN276515 Landing Gear Wire Struts Fahrwerk-Verstrebung Jambes à ﬁ l du train d’atterrissage Gambe a ﬁ lo per carrello di atterraggio

0 HAN276516 Wing Tube Tragﬂ ächenverbinder Clé d’aile Tubo dell’ala

P

HAN276517 Fuel Tank Kraftstofftank Réservoir de carburant Serbatoio del carburante

Q

HAN276518 EP Motor Box EP-Motorkasten Boîtier du moteur EP Vano motore elettrico

R

HAN276519 Scale Parts Maßstabsgetreue Details Pièces de détails à l’échelle Dettagli in scala

 SMALL PARTS (NOT SHOWN) • KLEINTEILE (NICHT ABGEBILDET) • PETITES PIÈCES (NON REPRÉSENTÉES) • PARTI DI PICCOLE DIMENSIONI (NON MOSTRATE)

HAN276513 Decal Set Dekorbogen Planche de décoration Set di decalcomanie

 REQUIRED RADIO EQUIPMENT • ERFORDERLICHE RC AUSRÜSTUNG • ÉQUIPEMENT RADIO REQUIS • APPARECCHIATURE RADIO NECESSARIE

SPMAR636 AR636 6-Ch AS3X Sport Receiver AR636 AS3X-Sportempfänger mit 6Kanälen Récepteur AR636 AS3X Sport 6canaux Ricevitore AR636 AS3X Sport a 6 canali

SPMA3002 (2) Heavy-Duty Servo Extension 9-inch Servokabelverlängerung 230 mm (9 inch) Rallonge de servo, 230 mm Estensione servo 9 pollici

SPMA3008 Heavy-Duty Y-Harness 6-inch Heavy Duty Y-Kabelbaum, 152mm (6Zoll) Harnais résistant en Y de 15 cm (6 po) Prolunga a Y Heavy Duty, 15 cm

SPMA3054 Servo Connector Clips (25) Servosteckerklemmen (25) Attaches de connexion du servo (25) Morsetti servocomando (25)

SPMSA6110 (5) A6110 HV Standard Servo A6110 HV Standard Servo Servo standard A6110 HV Servo standard A6110 HV

4

Part # English Deutsch Français Italiano

 2-STROKE GAS • 2-TAKT BENZINER • 2 TEMPS ESSENCE • 2-TEMPI A BENZINA

EVOE15GX2 15GX Gas Engine with Pumped Carb 15GX 15cc Benzinmotor Moteur essence 15GX 15cc Motore a benzina 15GX 15cc

EVOM9 15cc Inverted Wraparound Mufﬂ er 15cc invertierte Wraparound-Schalldämpfer Silencieux global inversé 15cc Silenziatore invertito, avvolgente, 15cc

HAN279012 1-inch Spinner Nut 5/16-24: P-47D-1 1-Zoll Spinner-Mutter, 5/16-24: P-47D-1 Écrou de cône de 2,54 cm (1 po), 5/16-24: P-47D-1 Dado dell’ogiva da 2,54 mm 5/16-24: P-47D-1

APC14060 Competition Propeller, 14 x 6 Competition Propeller, 14 x 6 Hélice 14 x 6 Competition Elica da competizione, 14 x 6

SPMSA6110 (5) A6110 HV Standard Servo A6110 HV Standard Servo Servo standard A6110 HV Servo standard A6110 HV

DUB799 Tygon Gas Tubing, 3-foot Medium Tygon-Gasrohre, 1 m (3 Fuß) m Durchschnitt Tube à essence Tygon, 91,4 cm (3 pi) moyen Tubo per carburante Tygon, 3 piedi, medio

HAN116 Fuel Filler with “T” and Overﬂ ow Fitting Hangar 9 Tanknippel mit T Stück u. Überlauf Fitting Point de remplissage de carburant avec coupleur en T Bocchettone di riempimento carburante con

SPM9530 Spektrum™ 3-Wire Switch Harness Spektrum™ dreiadriges Schalterkabel Câblage d’interrupteur 3 ﬁ ls Spektrum™ Interruttore di accensione a 3 ﬁ li Spektrum™

EVOA112 (2) Evolution 3 Wire Ignition/Receiver Switch Evolution Zündschalter Interrupteur Evolution 3 ﬁ ls Allumage/RX

Evolution, interruttore a 3 ﬁ li accensione/

ricevitore

SPMB2000LPRX 2000mAh 2S 7.4V LiPo Receiver Battery LiPo-Empfängerakku (7,4 V / 2000 mAh) Batterie Li-Po de récepteur 7,4 V 2000 mAh Batteria per ricevitore da 7,4 V Li-Po, 2.000 mAh

SPMB4000LPRX 4000mAh 2S 7.4V LiPo Receiver Battery LiPo-Empfängerakku (7,4 V / 4000 mAh) Batterie Li-Po de récepteur 7,4 V 4000 mAh Batteria per ricevitore da 7,4 V Li-Po, 4.000 mAh

 ELECTRIC POWER • ELEKTROANTRIEB • MOTEUR ELECTRIQUE (EP) • MOTORE ELETTRICO

EFLM4060B Power 60 BL Outrunner Motor, 470Kv Bürstenloser Außenläufer-Motor Leistung 60, 470Kv

Moteur à cage tournante sans balais

Power 60 de 470Kv

Motore brushless a cassa rotante

Power 60, 470Kv

CSE010009700 Talon 90-Amp 25V BL ESC W/20amp BEC

Talon 90 A 25 V bürstenloser Geschwindigkeitsregler

mit 20 A BEC

Variateur ESC Talon 90 A 25 V BL avec BEC 20 A ESC BL Talon 90-Amp 25 V con BEC 20amp

KXSB0029 7000mAh 6S 22.2V 30C LiPo, 10AWG: EC5 7000 mA 6S 22,2 V 30C LiPo-Akku,10 AWG EC5

Batterie Li-Po 6S 22,2V 7000mA 30C, 10AWG prise

EC5

Batteria LiPo 30C 22,2V 6S 7000 mAh,10AWG

EC5

APC16080E Electric Propeller, 16 x 8E Elektro Propeller, 16 x 8E Hélice électrique, 16 x 8E Elica elettrica sottile, 16 x 8E

HAN279011 1-inch Spinner Nut 8 x 1.25: P-47D-1 1-Zoll Spinner-Mutter, 8 x 1,25: P-47D-1 Écrou de cône de 2,54 cm (1 po), 8 x 1,25: P-47D-1 Dado dell’ogiva da 2,54 mm 8 x 1,25: P-47D-1

SPMSA6110 (4) A6110 HV Standard Servo A6110 HV Standard Servo Servo standard A6110 HV Servo standard A6110 HV

EFLAEC506 EC5 Extension Lead with 6-inch Wire, 10Awg EC5 Verlängerungsleitung mit 6-Zoll-Kabel, 10Awg Rallonge EC5 avec ﬁ l de 15 cm (6 po), 10 AWG

Cavo di prolunga EC5 con ﬁ lo da 15,24 cm, 10

AWG

SPMA3003 Heavy-Duty Servo Extension 12-inch Servokabelverlängerung 300 mm (12 inch) Rallonge de servo, 300 mm Estensione servo 12 pollici

 OPTIONAL ELECTRIC RETRACTS • OPTIONALES ELEKTRISCHES EINZIEHFAHRWERK • TRAINS RÉTRACTABLES ÉLECTRIQUES OPTIONNELS • ELEMENTI RETRATTILI ELETTRICI OPZIONALI

EFLG520 60-120 95-Degree Electric Rotating Retracts

60–120 95° drehbare, elektrische Einfahrvorrichtungen

Système de rentrée rotatif électrique 60–120

95degrés

Elemento retrattile rotante elettrico 60–120, 95

gradi

EFLG520F4U F4U Shock-Absorbing Strut Set F4U Dämpferstreben Set Paire de jambes amorties pour F4U Set gambe ammortizzate F4U

SPMA3001 (2) Heavy-Duty Servo Extension 3-inch Servokabelverlängerung 75 mm (3 inch) Rallonge de servo, 75 mm Estensione servo 3 pollici

 REQUIRED ADHESIVES • ERFORDERLICHE KLEBSTOFFE • TYPES DE COLLES • ADESIVI NECESSARI

DLMAD44 Roket Rapid CA 5-10 sec: 20g Roket Rapid CA 5-10 s: 20g Colle cyano Roket Rapid 5-10 sec: 20g Colla cianoacrilica Roket Rapid 5-10 sec: 20 g

DLMAD45 Roket Max CA 10-20 sec: 20g Roket Max CA 10-20 s: 20g Colle cyano Roket Max 10-20 sec: 20g Colla cianoacrilica Roket Max 10-20 sec: 20 g

PAAPT715 CA Accelerator Sekundenkleber (CA) Aktivator Accélérateur de colle CA Accelerante colla CA

PAAPT37 5-Minute Epoxy 5 Minuten Epoxy Époxy 5 minutes Colla epossidica 5 minuti

PAAPT35 15-Minute Epoxy 15 Minuten Epoxy Époxy 15 minutes Colla epossidica 15 minuti

PAAPT42 Threadlock Schraubensicherungslack Frein-ﬁ let Frenaﬁ letti

DLMAD12 R/C Modeller Canopy Glue: 4 oz R/C Modeller Kanzelkleber: 113,4g (4 oz) Colle à verrière R/C Modeller: 113g Colla per capottine R/C Modeller: 4 oz

5

F6F-5 Hellcat 15cc

Part # English Deutsch Français Italiano

 REQUIRED TOOLS • BENÖTIGTES WERKZEUG • OUTILS REQUIS • ATTREZZI NECESSARI

C-clamp Schraubzwinge Serre joint Morsetto a C

Drill Bohrer Mini-perceuse Trapano

Drill bit: 1/16-inch, 5/64-inch, 3/32-inch,

1/8-inch, 9/64-inch, 5/32-inch, 11/64-inch,

3/16-inch, 13/64-inch, 7/32-inch

Bohrer: 1,5mm, 2mm, 2,5mm, 3mm, 3,5mm, 4mm,

4,5mm, 5mm, 5,5mm, 6mm

Forêt : 1,5mm, 2mm, 2,5mm, 3mm, 3,5mm, 4mm,

4,5mm, 5mm, 5,5mm, 6mm

Punte per trapano: 1,5mm, 2mm, 2,5mm, 3mm,

3,5mm, 4mm, 4,5mm, 5mm, 5,5mm, 6mm

Felt-tipped pen Faserstift Feutre ﬁ n effaçable Pennarello

Epoxy brush Pinsel Pinceau Epoxy Spazzole epoxy

Flat ﬁ le Flachfeile Lime plate Lima piatta

Hemostats Klemme Pince Hemostat Pinzetta

Hex wrench: 1.5mm, 2mm, 2.5mm, 3mm Inbusschlüssel: 1,5mm, 2mm, 2,5mm, 3mm Tournevis hexagonal: 1,5mm, 2mm, 2,5mm, 3mm Chiave esag.: 1,5mm, 2mm, 2,5mm, 3mm

Hobby knife with #11 blade Hobbymesser mit # 11 Klinge Couteau : Lame numéro 11 Taglierino: #11 lama

Hook and loop tape Klettband Bande auto-agrippante Nastro a strappo

Hook and loop straps Klettgurt Bandes auto-agrippante Fascette a strappo

Isopropyl alcohol Isopropyl Alkohol Alcool isopropylique Alcol isopropilico

Low-tack tape Kreppband Adhésif de masquage Nastro a bassa aderenza

Needle nose pliers Spitzzange Pince ﬁ ne Pinze a becco stretto

Mixing cups and sticks Mischbecher und Rührstäbchen Récipients pour mélanger et bâtons Contenitori e stick per mixer colla

Nut driver: 7mm Steckschlüssel. 7mm Clés à douilles : 7mm Chiave per dadi: 7mm

Paper towels Papiertücher Papier absorbant Asciugamani di carta

Pencil Stift Crayon à papier Matita

Phillips screwdriver: #1, #2 Phillips Schraubendreher: #1, #2 Tournevis cruciforme: #1, #2 Cacciavite a croce: #1, #2

Pin vise Handbohrer Porte forets Trapano manuale

Pliers Zange Pince Pinze

Ruler Lineal Réglet Righello

Sandpaper Schleifpapier Papier de verre Carta vetrata

Scissors Schere Ciseaux Forbici

Side cutters Seitenschneider Pince coupante Lama laterale

Square Geodreieck Équerre Squadra

Tapered reamer Zulaufende Reibahle Alésoir conique Alesatore rastremato

Tie wraps Kabelbinder Colliers Fascette avvolgenti

T-pins T- Nadeln Epingles Spilli a T

Toothpicks Zahnstocher Cure dents Stuzzicadenti

Tubing bender Rohrbieger Cintreuse Curvatubi

Vise grips Klemmen Pince-étau Pinze bloccanti

 OPTIONAL ITEMS • OPTIONALE TEILE • ÉLÉMENTS OPTIONNELS • ARTICOLI OPZIONALI

SPMAR7350 AR7350 7 Channel AS3X Receiver AR7350 AS3X-Empfänger mit 7Kanälen Récepteur AS3X 7 canaux AR7350 Ricevitore AS3X a 7 canali AR7350

SPMSA6150 A6150 H-T / H-S Standard HV Servo A6150 H-T/H-S HV-Standard-Servo Servo A6150 H-T/H-S Standard HV Servo HV standard H-T / H-S A6150

EVOA100 Optical Ignition Kill Switch Optischer Zünd-Notausschalter Coupe-circuit optique d’allumage Sezionatore ottico accensione

SPMA3000 (2) Heavy-Duty Servo Extension 3-inch Servokabelverlängerung 75 mm (3 inch) Rallonge de servo, 75 mm Estensione servo 3 pollici

EVOE20GX2 20GX Gas Engine with Pumped Carb 20GX 20cc (1.20 cu. in.) Benzinmotor Moteur essence 20GX 20cc Motore a benzina 20GX 20cc (1.20 cu. in.)

APC16060 Competition Propeller, 16 x 6 Competition Propeller, 16 x 6 Hélice 16 x 6 Competition Elica da competizione, 16 x 6

6

NOTICE

All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon

Hobby, LLC. For up-to-date product literature, visit horizonhobby.com and click on the support tab for this product.

The following terms are used throughout the product literature to indicate various levels of potential harm when

operating this product:

Meaning of Special Language

WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage,

and serious injury OR create a high probability of superﬁ cial injury.

CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND a

possibility of serious injury.

NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND a little or

no possibility of injury.

WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating.

Failure to operate the product correctly can result in damage to the product, personal property and cause serious

injury.

This is a sophisticated hobby product. It must be operated with caution and common sense and requires some basic

mechanical ability. Failure to operate this Product in a safe and responsible manner could result in injury or damage

to the product or other property. This product is not intended for use by children without direct adult supervision. Do

not attempt disassembly, use with incompatible components or augment product in any way without the approval

of Horizon Hobby, LLC. This manual contains instructions for safety, operation and maintenance. It is essential to

read and follow all the instructions and warnings in the manual, prior to assembly, setup or use, in order to operate

correctly and avoid damage or serious injury.

AGE RECOMMENDATION: NOT FOR CHILDREN UNDER 14 YEARS. THIS IS NOT A TOY.

 USING THE MANUAL

This manual is divided into sections to help make assembly easier to understand.

 SAFETY WARNINGS AND PRECAUTIONS

Read and follow all instructions and safety precautions before use. Improper use can result in ﬁ re, serious injury and

damage to property.

Components

Use only with compatible components. Should any compatibility questions exist, please refer to the product

instructions, component instructions or contact the appropriate Horizon Hobby ofﬁ ce.

Flight

Fly only in open areas to ensure safety. It is recommended ﬂ ying be done at radio control ﬂ ying ﬁ elds. Consult local

ordinances before choosing a ﬂ ying location.

Propeller

Keep loose items that can become entangled in the propeller away from the prop. This includes loose clothing or other

objects such as pencils and screwdrivers. Keep your hands away from the propeller as injury can occur.

Batteries

Always follow the manufacturer’s instructions when using and disposing of any batteries. Mishandling of Li-Po

batteries can result in ﬁ re causing serious injury and damage.

Small Parts

This kit includes small parts and should not be left unattended near children as choking and serious injury could result.

 SAFE OPERATING RECOMMENDATIONS

• Inspect your model before every ﬂ ight to ensure it is airworthy.

• Be aware of any other radio frequency user who may present an interference problem.

• Always be courteous and respectful of other users in your selected ﬂ ight area.

• Choose an area clear of obstacles and large enough to safely accomodate your ﬂ ying activity.

• Make sure this area is clear of friends and spectators prior to launching your aircraft.

• Be aware of other activities in the vicinity of your ﬂ ight path that could cause potential conﬂ ict.

• Carefully plan your ﬂ ight path prior to launch.

• Abide by any and all established AMA National Model Aircraft Safety Code.

 BEFORE STARTING ASSEMBLY

• Remove parts from bag.

• Inspect fuselage, wing panels, rudder and stabilizer for damage.

• If you ﬁ nd damaged or missing parts, contact your place of purchase.

• Charge transmitter and receiver batteries.

• Center trims and sticks on your transmitter.

• For a computer radio, create a model memory for this particular model.

• Bind your transmitter and receiver, using your radio system’s instructions.

IMPORTANT: Rebind the radio system once all control throws are set. This will keep the servos from moving to

their endpoints until the transmitter and receiver connect. It will also guarantee the servo reversal settings are

saved in the radio system.

 FAA INFORMATION

If you own this product, you may be required to register with the FAA.

For up-to-date information on how to register with the FAA, please visit https://registermyuas.faa.gov/.

For additional assistance on regulations and guidance on UAS usage, visit knowbeforeyouﬂ y.org/.

 BUILDING PRECAUTIONS

During assembly, we recommend resting the parts on a soft surface such as a soft towel to help prevent denting the

sheeting.

7

F6F-5 Hellcat 15cc

Propeller

Halten Sie lose Gegenstände die sich im Propeller verfangen können weg vom Propeller. Dieses gilt auch für Kleidung

oder andere Objekte wie zum Beispiel Stifte oder Schraubendreher.

Halten Sie ihre Hände weg vom Propeller, es besteht akute Verletzungsgefahr.

Akkus

Folgen Sie immer den Herstelleranweisungen bei dem Gebrauch oder Entsorgung von Akkus. Falsche Behandlung von

LiPo Akkus kann zu Feuer mit Körperverletzungen und Sachbeschädigung führen.

Kleinteile

Dieser Baukasten beinhaltet Kleinteile und darf nicht unbeobachtet in der Nähe von Kindern gelassen werden, da die

Teile verschluckt werden könnten mit ernsthaften Verletzung zur Folge.

 EMPFEHLUNGEN ZUM SICHEREN BETRIEB

• Überprüfen Sie zur Flugtauglichkeit ihr Modell vor jedem Flug.

• Beachten Sie andere Piloten deren Sendefrequenzen ihre Frequenz stören könnte.

• Begegnen Sie anderen Piloten in ihrem Fluggebiet immer höﬂ ich und respektvoll.

• Wählen Sie ein Fluggebiet, dass frei von Hindernissen und groß genug ist.

• Stellen Sie vor dem Start sicher, dass die Fläche frei von Freunden und Zuschauern ist.

• Beobachten Sie den Luftraum und andere Flugzeuge/Objekte die ihren Flugweg kreuzen und zu einem Konﬂ ikt

führen könnten.

• Planen Sie sorgfältig ihren Flugweg vor dem Start.

 VOR DEM ZUSAMMENBAU

• Entnehmen Sie zur Überprüfung jedes Teil der Verpackung.

• Überprüfen Sie den Rumpf, Tragﬂ ächen, Seiten- und Höhenruder auf Beschädigung.

• Sollten Sie beschädigte oder fehlende Teile feststellen, kontaktieren Sie bitte den Verkäufer.

• Laden des Senders und Empfängers.

• Zentrieren der Trimmungen und Sticks auf dem Sender.

• Sollten Sie einen Computersender verwenden, resetten Sie einen Speicherplatz und benennen ihn nach dem Modell.

• Sender und Empfänger jetzt nach den Bindeanweisung des Herstellers zu binden.

WICHTIG: Wir empfehlen dringend nachdem alle Einstellungen vorgenommen worden sind, das Modell neu zu binden.

Dieses verhindert, dass die Servos in die Endanschläge laufen bevor sich Sender und Empfänger verbunden haben. Es

garantiert auch, dass die Servoreverseeinstellungen in der RC Anlage gesichert sind.

 HINWEISE ZUM BAU

Während des Zusammenbaus empfehlen wird, dass die Teile auf einer weichen Oberﬂ äche, wie einem Handtuch,

abgelegt werden, um ein Eindrücken der Bleche zu verhindern.

HINWEIS

Alle Anweisungen, Garantien und anderen zugehörigen Dokumente können im eigenen Ermessen von Horizon Hobby,

LLC. jederzeit geändert werden Die aktuelle Produktliteratur ﬁ nden Sie auf horizonhobby.com unter der Registerkarte

„Support“ für das betreffende Produkt.

Spezielle Bedeutungen

Die folgenden Begriffe werden in der gesamten Produktliteratur verwendet, um auf unterschiedlich hohe

Gefahrenrisiken beim Betrieb dieses Produkts hinzuweisen:

WARNUNG: Wenn diese Verfahren nicht korrekt befolgt werden, ergeben sich wahrscheinlich Sachschäden,

Kollateralschäden und schwere Verletzungen ODER mit hoher Wahrscheinlichkeit oberﬂ ächliche Verletzungen.

ACHTUNG: Wenn diese Verfahren nicht korrekt befolgt werden, ergeben sich wahrscheinlich Sachschäden UND die

Gefahr von schweren Verletzungen.

HINWEIS: Wenn diese Verfahren nicht korrekt befolgt werden, können sich möglicherweise Sachschäden UND geringe

oder keine Gefahr von Verletzungen ergeben.

WARNUNG: Lesen Sie die GESAMTE Bedienungsanleitung, um sich vor dem Betrieb mit den Produktfunktionen

vertraut zu machen. Wird das Produkt nicht korrekt betrieben, kann dies zu Schäden am Produkt oder persönlichem

Eigentum führen oder schwere Verletzungen verursachen.

Dies ist ein hochentwickeltes Hobby-Produkt. Es muss mit Vorsicht und gesundem Menschenverstand betrieben

werden und benötigt gewisse mechanische Grundfähigkeiten. Wird dieses Produkt nicht auf eine sichere und

verantwortungsvolle Weise betrieben, kann dies zu Verletzungen oder Schäden am Produkt oder anderen Sachwerten

führen. Dieses Produkt eignet sich nicht für die Verwendung durch Kinder ohne direkte Überwachung eines

Erwachsenen. Verwenden Sie das Produkt nicht mit inkompatiblen Komponenten oder verändern es in jedweder Art

ausserhalb der von Horizon Hobby, LLC vorgegebenen Anweisungen. Diese Bedienungsanleitung enthält Anweisungen

für Sicherheit, Betrieb und Wartung. Es ist unbedingt notwendig, vor Zusammenbau, Einrichtung oder Verwendung

alle Anweisungen und Warnhinweise im Handbuch zu lesen und zu befolgen, damit es bestimmungsgemäß betrieben

werden kann und Schäden oder schwere Verletzungen vermieden werden.

NICHT GEEIGNET FÜR KINDER UNTER 14 JAHREN. DIES IST KEIN SPIELZEUG.

 ÜBER DIESE ANLEITUNG

Diese Anleitung ist zur Vereinfachung des Zusammenbaues in Sektionen unterteilt.

 WARNUNGEN UND SICHERHEITS-VORKEHRUNGEN

Bitte lesen und befolgen Sie alle Anweisungen und Sicherheitsvorkehrungen vor dem Gebrauch. Falscher, nicht

sachgemäßer Gebrauch kann Feuer, ernsthafte Verletzungen und Sachbeschädigungen zur Folge haben.

Komponenten

Verwenden Sie mit dem Produkt nur kompatible Komponenten. Sollten Fragen zur Kompatibilität auftreten, lesen Sie

bitte die Produkt- oder Bedienungsanweisung oder kontaktieren den Service von Horizon Hobby.

Fliegen

Fliegen Sie um Sicherheit garantieren zu können, nur in weiten offenen Gegenden. Wir empfehlen hier den Betrieb auf

zugelassenen Modellﬂ ugplätzen. Bitte beachten Sie lokale Vorschriften und Gesetze, bevor Sie einen Platz zum Fliegen

wählen.

8

L’hélice

Gardez éloignés tous les éléments qui pourraient être attrapés par l’hélice. Cela inclut les vêtements larges ou les

objets comme des outils par exemple. Gardez toujours vos mains à distance pour éviter tout cas de blessures.

Les batteries

Suivez toujours les instructions du fabricant de vos batteries. Une mauvaise manipulation d’une batterie Li-Po peut

entraîner un incendie causant de graves dégâts matériels et des blessures corporelles.

Petites pièces

Ce kit contient des petites pièces qui ne doivent pas être laissées à la portée des enfants, ces pièces sont dangereuses

pour eux et peuvent entraîner de graves blessures.

 CONSIGNES DE SÉCURITÉ CONCERNANT L’UTILISATION

• Inspectez votre modèle avant chaque vol.

• Surveillez les fréquences utilisées à proximité.

• Soyez toujours courtois et respectueux des autres utilisateurs de la zone de vol.

• Choisissez une zone dégagée de tout obstacle et sufﬁ samment grande pour voler en toute sécurité.

• Contrôlez que la zone est libre de spectateurs avant de lancer votre modèle.

• Soyez conscient des autres activités aux alentours de votre vol, risque de conﬂ it potentiel.

• Planiﬁ ez votre vol avant de le commencer.

 AVANT DE COMMENCER L’ASSEMBLAGE

• Retirez toutes les pièces des sachets pour les inspecter.

• Inspectez soigneusement le fuselage, les ailes et les empennages.

• Si un élément est endommagé, contactez votre revendeur.

• ll est recommandé de préparer tous les éléments du système de la radio.

• Cela inclut la charge des batteries comme la mise au neutre des trims et des manches de votre émetteur.

• Si vous utilisez une radio programmable, sélectionnez une mémoire libre aﬁ n d’y enregistrer les paramètres de ce

modèle.

• Nous vous recommandons d’affecter maintenant le récepteur à l’émetteur en suivant les instructions fournies avec

votre radio.

IMPORTANT: Il est hautement recommandé de ré-affecter le système une fois que les courses seront réglées. Cela

empêchera les servos d’aller en butée lors de la connexion du système. Cela garantit également que la direction des

servos est enregistrée dans l’émetteur.

 PRÉCAUTIONS D’ASSEMBLAGE

Lors de l’assemblage de votre modèle, nous vous recommandons de poser les pièces sur une surface douce comme

une serviette douce pour éviter d’abîmer l’entoilage.

REMARQUE

La totalité des instructions, garanties et autres documents est sujette à modiﬁ cation à la seule discrétion d’Horizon

Hobby, LLC. Pour obtenir la documentation àjour, rendez-vous sur le site horizonhobby.com et cliquez sur l’onglet de

support de ce produit.

Signiﬁ cation de certains termes spéciﬁ ques

Les termes suivants sont utilisés dans l’ensemble du manuel pour indiquer différents niveaux de danger lors de

l’utilisation de ce produit:

AVERTISSEMENT: Procédures qui, si elles ne sont pas suivies correctement, peuvent entraîner des dégâts matériels

et des blessures graves OU engendrer une probabilité élevée de blessure superﬁ cielle.

ATTENTION: Procédures qui, si elles ne sont pas suivies correctement, peuvent entraîner des dégâts matériels ET des

blessures graves.

REMARQUE: Procédures qui, si elles ne sont pas suivies correctement, peuvent entraîner des dégâts matériels ET

éventuellement un faible risque de blessures.

AVERTISSEMENT: Lisez la TOTALITÉ du manuel d’utilisation aﬁ n de vous familiariser avec les caractéristiques du

produit avant de le faire fonctionner. Une utilisation incorrecte du produit peut entraîner sa détérioration, ainsi que des

risques de dégâts matériels, voire de blessures graves.

Ceci est un produit de loisirs sophistiqué. Il doit être manipulé avec prudence et bon sens et requiert des aptitudes

de base en mécanique. Toute utilisation irresponsable de ce produit ne respectant pas les principes de sécurité peut

provoquer des blessures, entraîner des dégâts matériels et endommager le produit. Ce produit n’est pas destiné à

être utilisé par des enfants sans la surveillance directe d’un adulte. N’essayez pas de modiﬁ er ou d’utiliser ce produit

avec des composants incompatibles hors des instructions fournies par Horizon Hobby, LLC. Ce manuel comporte des

instructions relatives à la sécurité, au fonctionnement et à l’entretien. Il est capital de lire et de respecter la totalité

des instructions et avertissements du manuel avant l’assemblage, le réglage et l’utilisation, ceci aﬁ n de manipuler

correctement l’appareil et d’éviter tout dégât matériel ou toute blessure grave.

14 ANS ET PLUS. CECI N’EST PAS UN JOUET.

 UTILISATION DU MANUEL

Ce manuel est divisé en sections pour vous aider à comprendre plus facilement l’assemblage.

 AVERTISSEMENTS RELATIFS À LA SÉCURITÉ

Lisez et suivez toutes les instructions relatives à la sécurité avant utilisation. Une utilisation inappropriée peut entraîner

un incendie, de graves blessures et des dégâts matériels.

Composants

Utilisez uniquement des composants compatibles. Si vous avez des questions concernant la compatibilité, référez-vous

à ce manuel ou contactez le service technique Horizon Hobby.

Le vol

Volez uniquement dans des zones dégagées pour un maximum de sécurité. Il est recommandé d’utiliser les pistes des

clubs d’aéromodélisme. Consultez votre mairie pour connaître les sites autorisés.

9

F6F-5 Hellcat 15cc

AVVISO

Tutte le istruzioni, le garanzie e gli altri documenti pertinenti sono soggetti a cambiamenti a totale discrezione di

Horizon Hobby, LLC. Per una documentazione aggiornata sul prodotto, visitare il sito www.horizonhobby.com e fare

clic sulla sezione Support per questo prodotto.

Signiﬁ cato dei termini particolari

In tutta la documentazione relativa al prodotto sono utilizzati iseguenti termini per indicare vari livelli di potenziale

pericolo durante il funzionamento:

AVVERTENZA: Procedure che, se non debitamente seguite, espongono alla possibilità di danni alla proprietà ﬁ sica

opossono omportare un’elevata possibilità di provocare ferite superﬁ ciali. Ulteriori precauzioni per la sicurezza e

avvertenze.

ATTENZIONE: Procedure che, se non sono seguite correttamente, possono creare danni materiali E possibili gravi

lesioni.

AVVISO: Procedure che, se non sono seguite correttamente, possono creare danni materiali E nessuna oscarsa

possibilità di lesioni.

AVVERTENZA: Leggere TUTTO il manuale di istruzioni e prendere familiarità con le caratteristiche del prodotto, prima

di farlo funzionare. Un utilizzo scorretto del prodotto può causare danni al prodotto stesso, alle persone oalle cose,

provocando gravi lesioni.

Questo è un prodotto di hobbistica soﬁ sticato e NON un giocattolo. È necessario farlo funzionare con cautela e

responsabilità e avere conoscenze basilari di meccanica. Se questo prodotto non è utilizzato in maniera sicura e

responsabile potrebbero veriﬁ carsi lesioni odanni al prodotto stesso oad altre proprietà. Non è un prodotto adatto

aessere utilizzato dai bambini senza la diretta supervisione di un adulto. Non usare componenti non compatibili

o alterare il prodotto in nessuna maniera al di fuori delle istruzioni fornite da Horizon Hobby, LLC. Questo manuale

contiene le istruzioni per un funzionamento e una manutenzione sicuri. È fondamentale leggere e seguire tutte le

istruzioni e le avvertenze del manuale prima di montare, conﬁ gurare ofar funzionare il Prodotto, al ﬁ ne di utilizzarlo

correttamente e di evitare danni olesioni gravi.

MINIMO 14 ANNI. NON È UN GIOCATTOLO.

 COME USARE IL MANUALE

Questo manuale è diviso in sezioni per rendere più facile la comprensione del montaggio.

 AVVERTIMENTI E PRECAUZIONI PER LA SICUREZZA

Prima dell’uso leggere attentamente tutte le istruzioni e le precauzioni per la sicurezza. In caso contrario si potrebbero

procurare incendi, danni o ferite.

Componenti

Usare solo componenti compatibili. Se ci fossero dubbi riguardo alla compatibilità, è opportuno far riferimento alle

istruzioni relative al prodotto o ai componenti oppure rivolgersi al reparto Horizon Hobby di competenza.

Volo

Per sicurezza volare solo in aree molto ampie. Meglio se in campi volo autorizzati per modellismo. Consultare le

ordinanze locali prima di scegliere luogo dove volare.

Elica

Tenere gli oggetti liberi (vestiti, penne, cacciaviti, ecc.) lontano dall’elica, prima che vi restino impigliati. Bisogna fare

attenzione anche con le mani perché c’è il rischio di ferirsi anche gravemente.

Batterie

Quando si maneggiano o si utilizzano le batterie, bisogna attenersi alle istruzioni del costruttore; il rischio è di procurare

incendi, specialmente con le batterie LiPo, con danni e ferite serie.

Piccole parti

Questo kit comprende delle parti di piccole dimensioni e non lo si può lasciare incustodito se c’è la presenza di bambini

che li possono inghiottire e rimanere soffocati o intossicati.

 RACCOMANDAZIONI PER OPERARE IN SICUREZZA

• Controllare attentamente il modello prima di ogni volo per accertarsi che sia idoneo.

• Essere consapevoli che un altro utente della frequenza in uso, potrebbe procurare delle interferenze.

• Essere sempre cortesi e rispettosi nei confronti degli altri utilizzatori dell’area in cui ci si trova.

• Scegliere un’area libera da ostacoli e abbastanza ampia da permettere lo svolgimento del volo in sicurezza.

• Prima del volo veriﬁ care che l’area sia libera da amici e spettatori.

• Stare attenti alle altre attività che si svolgono in vicinanza della vostra traiettoria di volo, per evitare possibili conﬂ itti.

• Pianiﬁ care attentamente il volo prima di lanciare il modello.

• Rispettare sempre scrupolosamente le regole stabilite dall’associazione locale.

 PRIMA DI INIZIARE IL MONTAGGIO

• Togliere tutti i pezzi dalla scatola.

• Veriﬁ care che la fusoliera, l’ala e i piani di coda non siano danneggiati.

• Se si trovano parti danneggiate, contattare il negozio da cui è stato acquistato.

• Caricare il trasmettitore e la batteria di volo.

• Centrare stick e trim sul trasmettitore.

• Con una radio computerizzata creare una nuova memoria per questo modello.

• Facendo riferimento alle istruzioni del radiocomando, connettere (bind) trasmettitore e ricevitore.

IMPORTANTE: Ripetere la procedura di connessione una volta regolate le corse, per evitare che i servi vadano a ﬁ ne

corsa. Garantirà anche che le impostazioni di inversione del servo vengano salvate nel sistema radio.

 PRECAUZIONI PER LA COSTRUZIONE

Durante l’assemblaggio noi consigliamo di appoggiare le varie parti su di una superﬁ cie morbida come un

asciugamano di spugna per evitare ammaccature al rivestimento.

10

 TRANSPORTATION AND STORAGE

Use the 3-view drawing at the back of this manual to

determine the amount of space required to transport and

store your model. The model can be disassembled, so the

amount of room necessary can vary. We recommend the

use of a wing bag to help protect these surfaces during

transport and storage. The control horns and linkages can

also cause damage to nearby surfaces even when placed

in storage bags. Always place surfaces so the tops are

together to prevent damage from the control horns and

linkages.

 ENGINE SELECTION

We recommend the 15cc Evolution

®

engine for this

model. It provides great performance and more than

scale aerobatic capability. We understand some of our

customers may want more than scale performance. In

testing and development of the F6F-5 Hellcat, many

changes were made so it would accommodate the

20cc Evolution gas engine as an option. No changes

are required to the airframe to accommodate the

Evolution 20cc gas engine. Changes were made during

the development of the Hellcat to the ﬁ rewall, wing

joiner, elevator pushrod and rudder pushrod to cope

with the increase in performance. It is still advisable

to moderately use of full throttle. The 20cc is a large

power plant for a plane this size, and while full power

application on a upline is allot of fun, we advise against

misuse of the throttle in stages of the ﬂ ight such as

downlines, dives etc.

We found one area subjected to extra loads with the

larger power option was the large elevator and horizontal

stabilizer. The stabilizer structure has been assembled

to accommodate the increased power of the 20cc gas

engine. In addition, a larger than normal elevator pushrod

has been supplied with your model. We do recommend

the use of a metal-geared servo for the elevator to

compensate for the increased loads required from the

use of the larger gas engine.

 TRANSPORT UND LAGERUNG

Mit der Zeichnung aus drei Ansichten am Ende des

Handbuchs lässt sich ermitteln, wie viel Platz zum

Transport und zur Lagerung des Modells benötigt

wird. Das Modell kann demontiert werden, daher ist

der erforderliche Platz variabel. Die Empfehlung einer

Flügeltasche wird empfohlen, um diese Oberﬂ ächen bei

Transport und Lagerung zu schützen. Die Steuerhörner

und Gestänge können zudem Schäden an benachbarten

Oberﬂ ächen verursachen, auch wenn sie in Taschen

gelagert sind. Oberﬂ ächen stets so platzieren, dass

die Oberseiten aneinander liegen, um Schäden durch

Steuerhörner und Gestänge zu vermeiden.

 MOTORWAHL

Wir empfehlen den 15cc Evolution

®

-Motor für dieses

Modell. Er bietet eine großartige Leistung und mehr

als nur eine maßstabgetreue Kunstﬂ ugfähigkeit. Wir

wissen, dass einige unserer Kunden mehr wollen, als

nur die maßstabgetreue Leistung. Bei der Erprobung und

Entwicklung der F6F-5 Hellcat wurden viele Änderungen

vorgenommen, damit sie den 20ccm Evolution-

Gasmotor als Option unterbringen kann. Am Rahmen

sind keine Änderungen notwendig, damit der Evolution

20cc Gasmotor passt. Änderungen an Brandschott,

Tragﬂ ächen-Verbinder, Höhenruder-Gestänge und

Seitenruder-Gestänge wurden während der Entwicklung

der Hellcat vorgenommen, um die Leistungszunahme zu

bewältigen. Es ist immer noch ratsam, Vollgas mäßig zu

verwenden. Der 20cc Motor ist für ein Flugzeug dieser

Größe ein großes Kraftpaket, und während das Anlegen

der vollen Leistung auf einer Upline viel Spaß macht,

raten wir davor, die Gaszufuhr in Phasen des Fluges wie

Downlines, Sturzﬂ ügen usw. zu missbrauchen.

Ein Bereich, der zusätzlichen Belastungen bei

größeren Antriebsoptionen ausgesetzt war, ist das

große Höhenruder und der horizontale Stabilisator. Die

Stabilisatorstruktur wurde zusammengebaut, um die

erhöhte Leistung des 20-cc-Gasmotors aufzunehmen.

Außerdem wurde eine größere als das normale

Höhenruder-Gestänge mit Ihrem Modell geliefert. Wir

empfehlen die Verwendung eines Metallgetriebeservos

für das Höhenruder, um die größeren Lasten

auszugleichen, die durch die Verwendung des größeren

Gasmotors benötigt werden.

 TRANSPORT ET STOCKAGE

Utilisez le schéma à 3 vues à l’arrière de ce manuel

pour déterminer l’espace nécessaire pour transporter

et stocker votre maquette. La maquette peut être

démontée, l’espace nécessaire peut donc varier. Nous

vous conseillons d’utiliser un sac à ailes pour protéger

ces surfaces lors du transport et du stockage. Les

renvois de commande et tringleries peuvent également

endommager les surfaces proches même si rangés dans

des sacs de rangement. Placez toujours ces surfaces

de manière à ce que les sommets soient ensemble

pour prévenir tout dommage causé par les renvois de

commande et les tringleries.

 CHOIX DU MOTEUR

Nous recommandons d’utiliser le moteur Evolution

®

15cc pour cette maquette. Il assure des performances

optimales et bien plus par rapport aux fonctions

acrobatiques des modèles réduits. Nous comprenons

que certains de nos clients souhaitent peut-être plus

que des performances de maquette. Lors des tests et du

développement du Hellcat F6F-5, plusieurs modiﬁ cations

ont été apportées aﬁ n de proposer le moteur à essence

Evolution 20cc comme option. Aucune modiﬁ cation

requise sur la structure de vol pour utiliser le moteur

à essence Evolution 20cc. Des modiﬁ cations ont été

apportées pendant le développement du Hellcat au pare-

feu, la tige, la barre de liaison de l’élévateur et la barre

de liaison de la gouverne pour assurer l’augmentation

des performances. Il est conseillé d’utiliser de manière

modérée les pleins gaz. Le moteur 20cc correspond à

une grande centrale pour un avion de cette taille, et bien

qu’une application en pleine puissance en montée soit

très amusant, nous déconseillons d’accélérer lors de

certaines étapes du vol, par ex. pendant les descentes,

les plongeons, etc.

Nous avons observé une zone soumise à des charges

supplémentaires avec l’option d’alimentation plus

grande: un grand élévateur et le stabilisateur horizontal.

La structure du stabilisateur a été montée pour s’adapter

à la plus grande puissance du moteur à essence 20cc.

De plus, une barre de liaison d’élévateur plus large

qu’à l’habitude est fournie avec votre maquette. Nous

vous recommandons d’utiliser un servo à engrenages

métalliques pour l’élévateur aﬁ n de compenser les

charges supplémentaires requises pour l’utilisation d’un

plus grand moteur à essence.

 TRASPORTO E DEPOSITO

Fare riferimento al trittico riportato sul retro di questo

manuale per determinare lo spazio necessario al

trasporto e all’immagazzinaggio del modello. Il modello

può essere smontato e, di conseguenza, lo spazio

necessario può variare. È consigliabile usare delle borse

alari per proteggere queste superﬁ ci durante il trasporto

e l’immagazzinaggio. Squadrette e rinvii possono

danneggiare le superﬁ ci circostanti anche all’interno delle

borse. Per prevenire questo problema, sistemare sempre

le superﬁ ci facendo combaciare le superﬁ ci superiori.

 SCELTA DEL MOTORE

Per questo modello raccomandiamo il motore Evolution

®

15cc. Offre grandi prestazioni e capacità acrobatiche

superiori rispetto a quelle in scala. Crediamo infatti

che alcuni dei nostri clienti desiderino prestazioni

migliori di quelle in scala. Durante le prove e lo sviluppo

dell’F6F-5 Hellcat, sono state effettuate diverse modiﬁ che

per potervi inserire il motore a benzina opzionale

Evolution 20cc. L’utilizzo di questo motore non richiede

alcuna modiﬁ ca alla cellula. I cambiamenti apportati

all’Hellcat in fase di sviluppo hanno riguardato la paratia

tagliaﬁ amma, l’elemento di giunzione dell’ala, l’asta di

comando dell’elevatore e del timone, mirati a supportare

prestazioni maggiori. Si consiglia di utilizzare la massima

potenza con moderazione. Il 20cc è un motore molto

potente per un aeromodello di queste dimensioni, e se

applicare la massima potenza in una traiettoria verticale

è molto divertente, sconsigliamo un uso improprio del

comando motore in fasi di volo come discese verticali,

picchiate, ecc.

Una delle aree che deve sostenere un peso maggiore se

si installa il motore opzionale è quella in cui di trovano

il grande elevatore e lo stabilizzatore orizzontale. La

struttura dello stabilizzatore è stata assemblata per

supportare la maggiore potenza del motore a benzina

20cc. Inoltre, il modello è dotato di un’asta di comando

dell’elevatore di larghezza superiore alla norma.

Consigliamo l’uso di un servo con ingranaggi in metallo

per l’elevatore per compensare i carichi più elevati dovuti

alla scelta di un motore a benzina più grande.

11 EN

F6F-5 Hellcat 15cc

 AILERON INSTALLATION

1. Separate the aileron slightly from the wing so the hinges are

visible. Use a felt-tipped pen to make a mark indicating the

center of the hinges on both the aileron and wing. Make the

mark on the underside of the wing so it is less visible when

the model has been completed.

2. Remove the aileron from the wing. Set the hinges aside in a

safe location.

3. Test ﬁ t the white aileron control horn in the slot in the aileron.

Check that the horn is 90-degrees to the surface of the

aileron. If not, lightly trim the hole in the aileron to reposition

the control horn.

4. Place low-tack tape around the aileron control horn. The tape

should be 1/32-inch (1mm) from the control horn as shown.

5. Use medium-grit sandpaper to lightly sand the aileron control

horn where it ﬁ ts into the aileron. Clean the sanded area

using a paper towel and isopropyl alcohol to remove any

debris or oils. This provides the surface texture necessary for

the epoxy to bond to.

6. Apply epoxy to the area of the control horns that ﬁ ts into the

slots. Use enough epoxy so the control horns will be fully

bonded to the ﬁ xed surfaces.

7. Remove the control horns from the control surfaces. Apply

epoxy to the slot in the aileron and ﬂ ap. Make sure the epoxy

gets into the slot for a good bond between the surfaces and

control horn.

8. Before the epoxy fully cures, remove the tape from around

the control horn. This will allow the epoxy to ﬂ ow around the

control horn, creating a small ﬁ llet between the control horn

and surface for a ﬁ nished look and secure bond.

9. Use a pin vise and 1/16-inch (1.5mm) drill bit to drill a hole in

the center of each hinge slot marked previously. Drill the hole

1/4-inch (6mm) deep into the wood. Drill holes in both the

wing and aileron hinges slots now.

 Drilling this hole provides a tunnel for the CA to fully wick

into the hinge and surrounding surface. Failure to drill this

hole may result in a hinge that may not be glued properly.

10. Place a T-pin in the center of each of the three hinges.

12EN

11. Slide the hinges into position in the aileron with the T-pin

resting against the edge of the control surface.

16. Check both the up and down movement of the hinges before

proceeding.

 Repeat this section for the remaining aileron installation.

12. Fit the aileron and ﬂ ap to the wing by inserting the hinges into

the slots in the wing. Position the aileron so the gap is equal

between the aileron and wing.

 AILERON SERVO INSTALLATION

17. Remove the aileron servo cover from the wing. Tape the string

to the wing so it won’t fall into the wing. Use a toothpick

or hobby knife to puncture the covering for the servo cover

mounting screws.

13. Apply thin CA to the top and bottom of each of the hinges.

Make sure to fully soak the hinges so the CA can wick into

the hinge and bond to the surrounding wood.

 Use thin CA so it wicks into the hinge. A thicker CA

will not wick into the hinge properly. Do not to allow the

CA to run over the covering on the wing and aileron.

18. Use a pin vise and 3/32-inch (2.5mm) drill bit to drill the holes

for the servo cover screws.

14. Allow the CA to cure for 10 to 15 minutes. Gently pull on the

ﬁ xed surface and control surface to make sure the hinges are

glued securely. If not, apply additional CA to secure each of

the hinges.

19. Use a #2 Phillips screwdriver to thread the M3 x 10 self-

tapping screws into the holes. Remove the screws before

proceeding to the next step.

 Do not press down excessively on the

screw as it could damage the structure.

15. Move the aileron through its range of travel to break in the

hinges.

20. Apply a small amount of thin CA to harden the threads

made in the previous step. Allow the CA to fully cure before

installing the aileron servo cover.

13 EN

F6F-5 Hellcat 15cc

5/8 inch

(16mm)

21. Use a pin vise and 5/32-inch (2mm) drill bit to drill the holes

for the servo mounting screws. Make sure to harden the

holes using the technique outlined in the previous steps.

Use the screws provided with the servo and a #1 Phillips

screwdriver when installing the screws.

26. When attaching the linkage to the aileron servo arm, use the

hole in the arm that is 5/8-inch (16mm) from the center of

the arm.

 The suggested measurements will result in a scale roll

rate. A longer servo arm can be used for a faster roll rate.

23. Secure the servo to the cover using a #1 Phillips screwdriver

and the screws provided with the servo.

28. Use the string to pull the servo lead through the wing and out

at the root.

22. Install the grommets and eyelets in the servos. Follow any

instructions included with the servo. Prepare both aileron

servos.

27. Tie or tape the string located inside the wing to the end of the

servo lead.

24. Secure a 12-inch (300mm) servo extension to the servo using

a commercially available retainer (SPMA3054).

25. Center the servo, then secure the servo arm so it is

perpendicular to the servo centerline. Use side cutters to

remove any unneeded servo arms.

29. Secure the servo to the wing using four M3 x 10 self-tapping

screws. Use a #2 Phillips screwdriver to tighten the screws.

30. Assemble and attach the aileron linkage to the servo arm. The

aileron pushrod is 2

3

/

8

-inches (60mm) in length.

14EN

31. Loosen the nuts, then place a drop of threadlock on the

linkage near the clevises. Tighten the nuts over the threadlock

and against the clevises.

 Repeat this section for the remaining

aileron servo installation.

 FIXED GEAR INSTALLATION - WIRE STRUT

32. Use a hobby knife with a #11 blade to remove the covering,

exposing the mounts for the ﬁ xed landing gear.

 The wire strut can be painted using Royal Blue paint

(TAM81503) so they blend in with the gear doors.

33. Use a drill and 13/64-inch (5mm) drill bit to enlarge the hole

in the wheel for the axle.

34. Use a ﬂ at ﬁ le to create a ﬂ at area on the ﬁ rst 1/4-inch (6mm)

of the landing gear. File a second ﬂ at area that is 1/4-inch

(6mm) wide centered 1

3

/

16

-inches (30mm) from the end of

the axle.

35. Prepare the M3 x 20 socket head cap screws by placing a

washer and lock washer on each screw.

36. Secure the landing gear using the screws prepared in the last

step. Make sure to place a drop of threadlock on each screw

before placing them in position. Use a 2.5mm hex wrench to

tighten the screws.

37. Slide a wheel collar on the axle. Secure the wheel collar

by tightening the M3 x 4 setscrew on the ﬂ at area made

previously. Make sure to place a drop of threadlock on the

setscrew before tightening it using a 1.5mm hex wrench.

38. Apply a drop of light machine oil to the axle.

39. Slide the wheel on the axle. Secure the wheel using a wheel

collar and M3 x 4 setscrew. Apply a drop of threadlock on the

setscrew before tightening it into position using a 1.5mm hex

wrench.

 Check that the wheel can rotate freely on the axle.

40. Trim the covering 1/8-inch (3mm) forward and aft of the

notch in the landing gear door to expose the underlying wood.

15 EN

F6F-5 Hellcat 15cc

41. Use medium CA to glue the gear door mounts to the gear

door.

42. Make sure to prepare a left and right gear door.

43. Roughen the wire strut where the gear door mounts meet

the strut. Use 15-minute epoxy and micro balloons to glue

the four gear door brackets to the top and bottom of the gear

door mounts and to the wire strut.

44. Before the epoxy cures, position the landing gear door so it

will not contact the ground during take-off and landing.

 Repeat this section for the remaining fixed gear installation.

 FIXED GEAR INSTALLATION - E-FLITE

®

SHOCK

ABSORBING STRUT

45. Use a hobby knife with a #11 blade to remove the covering

exposing the mounts for the ﬁ xed landing gear.

46. Use a rotary tool and cut-off wheel to cut the length of

the ﬁ xed gear wire to 13/16-inches (20mm) Use a ﬂ at ﬁ le

to make a ﬂ at area along the front edge of the remaining

landing gear wire.

47. Slide the strut on the landing gear wire. Tighten the

setscrews, securing the strut to the wire.

48. Place the axle in the strut. With the assembly ﬂ at on the work

surface, the body of the mount and axle will lay ﬂ at on the

work surface. If not, ﬁ le the ﬂ at area slightly to change the

positioning of the strut. Once set, the setscrews can have a

drop of threadlock applied and tightened into position using a

2mm hex wrench.

49. Use a pin vise and 1/8-inch (3mm) drill bit to drill the

mounting holes in the landing gear door using the

measurements shown in the photo.

50. Use an M3 x 5 button head screw to temporarily attach the

gear door mounts to the gear doors using the pre-drilled

holes in the gear door. Leave the screws slightly loose so the

mounts can be aligned with the strut. Use a 2mm hex wrench

when installing the screws.

 The gear doors can be painted using Royal

Blue paint (TAM81503) so they blend in with

the scale appearance of the model.

16EN

51. Slide the strut through the gear door mounts.

52. Prepare the M3 x 20 socket head cap screws by placing a

washer and lock washer on each screw.

53. Secure the landing gear using the screws prepared in the last

step. Make sure to place a drop of threadlock on each screw

before placing them in position. Use a 2.5mm hex wrench to

tighten the screws.

55. Use a drill and 13/64-inch (5mm) drill bit to enlarge the hole

in the wheel for the axle.

56. Apply a drop of light machine oil to the axle. Slide the axle

into the wheel. Slide a wheel collar on the axle, then secure it

using an M3 x 4 setscrew and 1.5mm hex wrench. Make sure

to use threadlock on the setscrew before installation.

 Check that the wheel can rotate freely on the axle.

57. Slide the axle into the strut. Apply a drop of threadlock on

the M3 x 3 setscrew supplied with the struts. Tighten the

setscrew on the ﬂ at using a 1.5mm hex wrench.

58. Position the landing gear door so it will not contact the ground

during take-off and landing. Also check that the gear door

is aligned with the wheel when viewing the door from the

bottom of the wing.

59. Apply a drop of threadlock on the M3 x 4 setscrew. Use a

1.5mm hex wrench to tighten the setscrew in the gear door

mounts. Install all four setscrews, securing the gear door

mounts to the strut. Tighten the button head screws that

secure the gear door to the mounts.

 Do not over-tighten the setscrews as this will damage

the gear door mounts or restrict the movement of the strut.

 Repeat this section for the remaining fixed gear installation.

54. Use a ﬂ at ﬁ le to make a ﬂ at area for the ﬁ rst 1/2-inch (12mm)

of the axle.

17 EN

F6F-5 Hellcat 15cc

 RETRACT WHEEL WELL INSTALLATION

60. Use a hobby knife and #11 blade to remove the covering from

the bottom of the wing to expose the opening for the retract.

61. Test ﬁ t the retract wheel well to the wing. Start trimming the

wheel well at the front to clear the landing gear mounts.

62. Remove the material from the wheel well so it ﬁ ts ﬂ ush with

the wing.

 Use care when trimming the plastic pieces to avoid chipping

the paint. The matching paint is listed in the front of this manual.

63. Check the ﬁ t of the retract to the wheel well. It will be

necessary to trim the wheel well accordingly.

64. Use hobby scissors to trim the wheel well to ﬁ t the retract.

Use medium grit sandpaper to smooth any rough edges after

trimming.

65. Lightly sand the outside of the wheel well where it contacts

the wing with medium grit sandpaper. Use a paper towel and

isopropyl alcohol to remove any oil or debris from the wheel

well.

66. Lightly sand the wing 1/8-inch (3mm) from the edge of the

opening with medium grit sandpaper. Use a paper towel and

isopropyl alcohol to remove any oil or debris from the wing

where the wheel well.

67. Use 15-minute epoxy or contact adhesive to glue the wheel

well to the wing. Use low-tack tape to hold the wheel well

tightly in position until the adhesive fully cures.

 The wheel wells can be touched up using Royal

Blue paint (TAM81503) so they blend in with the wing.

 Repeat this section for the remaining wheel well installation.

 RETRACT INSTALLATION - WIRE STRUT

68. Use a ﬂ at ﬁ le to make a ﬂ at area for the ﬁ rst 1/2-inch (12mm)

of the axle.

69. Position the axle on the wire strut so it is 5

1

/

2

-inches (140mm)

from the collar on the strut. This is an approximate position

for the axle.

18EN

70. Guide the lead from the retract along the side of the wheel

well. The lead can be retrieved in the same area as the

aileron extension.

71. Secure the retract in the wing using the hardware included

with the retract. Place a drop of threadlock on each of the

screws before installing them in the retract. Use a 2mm hex

wrench to tighten the screws.

 It may be necessary to use the spacers included with

the retracts to make sure there is no torsional stress on the

retract frame when tightened into position. Torsional stress can

sometimes cause intermittent operation of the retract unit.

72. With the gear in the up position, the axle must be centered in

the wheel well. Reposition the axle as necessary.

 We recommend making two flat areas with a

file to tighten the screws onto. This will prevent the

axle from rotating on the landing gear wire.

73. Place two nylon spacers on the axle. Apply a drop of light

machine oil on the axle.

74. Slide the wheel on the axle. Place the wheel collar included

with the retracts on the axle. Use the M3 x 3 setscrew to

secure the wheel collar on the axle. Make sure to place a

drop of threadlock on the setscrew before tightening it with a

1.5mm hex wrench.

75. Check that there is a slight amount of toe-in (roughly

1-degree). Adjustments can be made by loosening the two

setscrews on the strut near the mount using a 1.5mm hex

wrench.

 Always use threadlock on metal-to-metal fasteners.

76. Double-check that the wheel is centered in the wheel well.

Reposition the axle if necessary or bend the strut slightly so

the wheel is perfectly centered.

77. Trim the covering 1/8-inch (3mm) forward and aft of the

notch in the landing gear door to expose the underlying wood.

78. Use medium CA to glue the gear door mounts to the gear

door.

79. Make sure to prepare a left and right gear door.

19 EN

F6F-5 Hellcat 15cc

 Read through the following steps before installing the

gear doors. They must be aligned before the epoxy fully cures.

80. Roughen the wire strut where the gear door mounts meet

the strut. Use 15-minute epoxy and micro balloons to glue

the four gear door brackets to the top and bottom of the gear

door mounts and to the wire strut.

81. Position the landing gear door so it will not contact the ground

during take-off and landing.

82. Retract the landing gear. Position the gear door so it is parallel

to the bottom of the wing. Use a small amount of silicone

adhesive to glue the gear door mounts to the gear wire.

Check the position of the gear door as the adhesive cures.

 Repeat this section for the remaining retract installation.

 RETRACT INSTALLATION - E-FLITE

®

SHOCK

ABSORBING STRUT

83. Use a rotary tool and cut-off wheel to cut the length of the

retract gear wire to 13/16-inches (20mm) Use a ﬂ at ﬁ le

to make a ﬂ at area along the front edge of the remaining

landing gear wire.

85. Use an M3 x 5 button head screw to temporarily attach the

gear door mounts to the gear doors using the pre-drilled

holes in the gear door. Leave the screws slightly loose so the

mounts can be aligned with the strut. Use a 2mm hex wrench

when installing the screws.

 The gear doors can be painted using Royal

Blue paint (TAM81503) so they blend in with

the scale appearance of the model.

86. Slide the strut through the gear door mounts.

87. Fit the strut on the gear wire. Temporarily tighten the

setscrews to secure the strut to the wire using a 2mm hex

wrench.

 Do not over-tighten the setscrews

as this may damage the strut.

88. Guide the lead from the retract along the side of the wheel

well. The lead can be retrieved in the same area as the

aileron extension.

89. Secure the retract in the wing using the hardware included

with the retract. Place a drop of threadlock on each of the

screws before installing them in the retract. Use a 2mm hex

wrench to tighten the screws.

 It may be necessary to use the spacers included with

the retracts to make sure there is no torsional stress on the

retract frame when tightened into position. Torsional stress can

sometimes cause intermittent operation of the retract unit.

84. Use a pin vise and 1/8-inch (3mm) drill bit to drill the

mounting holes in the landing gear door using the

measurements shown in the photo.

20EN

90. Use a ﬂ at ﬁ le to make a ﬂ at are for the ﬁ rst 1/2-inch (12mm)

of the axle.

91. Use a drill and 13/64-inch (5mm) drill bit to enlarge the hole

in the wheel for the axle.

92. Apply a drop of light machine oil to the axle. Slide the axle

into the wheel. Slide a wheel collar on the axle, then secure it

using an M3 x 4 setscrew and 1.5mm hex wrench. Make sure

to use threadlock on the setscrew before installation.

 Check that the wheel can rotate freely on the axle.

93. Slide the axle into the strut. Apply a drop of threadlock on

the M3 x 3 setscrew supplied with the struts. Tighten the

setscrew on the ﬂ at using a 1.5mm hex wrench.

95. Check that the gear good closes ﬂ at against the wing, and

that the door does not interfere with the operation of the

retract. Once set, secure the gear door to the strut using four

M3 x 4 setscrews and a 1.5mm hex wrench. Remember to

tighten the screws holding the door to the mounts using a

2mm hex wrench at this time. Place a drop of threadlock on

all metal-to-metal fasteners.

 It may be necessary to lightly file the surface

of the gear door mounts that contact the gear door

so the door will lay flay against the wing.

 Do not over-tighten the setscrews as this will damage

the gear door mounts or restrict the movement of the strut.

 Repeat this section for the remaining retract installation.

 STABILIZER INSTALLATION

96. Remove the two thumb screws that secure the canopy hatch

to the fuselage.

 The nylon bolt can be shortened to make

securing the canopy hatch easier. A metal fastener

can also be substituted (not included).

97. Lift the canopy hatch from the fuselage at the rear. Slide the

hatch back and remove it from the fuselage. Set it aside in a

safe location.

94. Check that there is a slight amount of toe-in (roughly

1-degree). Adjustments can be made by loosening the

two setscrews on the strut near the mount using a 1.5mm

hex wrench. The ﬂ at on the retract wire may need slight

adjustment to ensure the retract strut does not rotate on the

wire.

 Always use threadlock on metal-to-metal fasteners.

98. Slide the wing tube into the wing tube socket.

 The wing tube may be a tight fit in the socket.

Polishing the wing tube with fine sand paper or steel

wool will help ease the installation of the wing tube.

La page charge ...

Hangar 9 HAN2765 Le manuel du propriétaire

Hangar 9 HAN2765 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents