SimpleTech STI-105HD Quick Installation Manual

Taper
Quick Installation Manual

Ce manuel convient également à

Q U I C K I N S T A L L A T I O N G U I D E
PCMCIA
ATA
Hard Drive
STI-105HD
STI-130HD
STI-170HD
The following statements are provided in accordance with Federal Communications
Commission (FCC) regulations. Please read these statements carefully before installing or
operating your hard drive.
Instruction to the User (USA)
This equipment has been tested and found to comply with the limits for a class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reason-
able protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different form
that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for
help.
This equipment has been certified to comply with the limits for a class B computing device,
pursuant to FCC Rules. In order to maintain compliance with FCC regulations, shielded
cables must be used with this equipment. Operation with non-approved equipment or
unshielded cables is likely to result in interference to radio and TV reception. The user is
cautioned that changes and modifications made to this equipment without the approval of
the manufacturer could void the user’s authority to operate this equipment.
Instruction to the User (Canada)
This digital apparatus does not exceed the class B limits for radio noise emissions from
digital apparatus set out in the radio interference regulations of the Canadian Department
of Communications.
Le present appareil numerique nemet pas de brutts radioelectriques depassant les limites
applicables aux appareils numeriques de la class B prescrites dans le reglement sur le
brouillage radioelectrique edicte apr le Ministere des Communications du Canada.
PRECAUTIONS
Do not drop or jar the card
Do not open the card.
Never remove the card while the computer is accessing the card
Place the computer and card out of direct sunlight, high or low tempera-
tures, and high humidity.
INSTALLATION PROCEDURE
The Simple Technology Type III hard disk drives are compatible with the
PCMCIA PC Card-ATA interface. They will work in any Type III slot provided
that the slot has a PCMCIA Release 2.0 compatible hardware and software
interface. If compatible PCMCIA software is not installed, then the PCMCIA
software provided must be installed.
NOTE: The drive has been formatted before shipment and should not require
reformatting before use.
Consult the reference manual that comes with your computer to locate the
PCMCIA Type III slot. Read additional information from the computer manual
regarding specific instructions on using the PCMCIA slot before installation.
To install the drive, proceed as follows:
NOTE: If your computer has Card and Socket Services installed, the drive
should work without any further driver installation, and you may skip
to Step 4.
1. Insert the PCMCIA driver disk into the appropriate drive.
2. Change the DOS prompt to the drive where you inserted the PCMCIA
driver disk. Type:
INSTALL <ENTER>
3. Carefully follow the on-screen instructions. Be absolutely sure to read
the on-screen instructions of each installation window before
continuing to the next installation window.
Depending on the choices that you make during the installation
process, new directories may be created on your hard disk, and your
AUTOEXEC.BAT and CONFIG.SYS files may be modified to install
the driver when you start your computer.
4. Hold the PCMCIA card with the 68-pin female PCMCIA connector
facing an available PCMCIA Type III slot.
5. Insert the card into the PCMCIA Type III slot. The keyed guide slots
on the PCMCIA card will not allow incorrect insertion. Insert the card
gently but firmly into the slot until it stops.
6. The drive has been formatted before shipment and should not require
reformatting before use. If you want to format it again, use the
following procedure.
Create a partition on the drive by typing:
“C:\CARDSOFT ATAINIT <Drive Letter>: <Enter>”
where <Drive Letter> is the letter of the new PCMCIA drive (usually D:
or E:).
7. The screen will show:
Fixed Cylinders: = 828 (105 MB), 1010 (130 MB), or 923 (170 MB)
Heads: = 8 (105 MB), 4 (130 MB), or 8 (170 MB)
Physical Sectors/Track: = 31 (105 MB), 63 (130 MB), or 45 (170 MB)
—and—
Hit ENTER to accept and continue or <P> to prompt. Press “<Enter>.”
Do you wish a compact format? Type “N” and press “<Enter>.”
8. After running ATAINIT, you must immediately format the drive with
the DOS format utility, using the “/U” option. Type “C:FORMAT
<Drive Letter>/U.” The drive will then be formatted and made ready
for use.
TECHNICAL SUPPORT
If you are experiencing difficulties with the installation, contact Technical
Support at the following :
Tel: 714-476-1180
1-800-367-7330
Fax: 714-476-1209
Web: http://www.simpletech.com
Limited Warranty
Simple Technology Incorporated guarantees its products to be of the highest quality, and to be free of defects in material,
design and workmanship. STI will repair or replace this product, without charge for either parts or labor, if it is returned
due to defects in material, design, and/or workmanship only. This guarantee applies only if the product has not been
misused, modified, repaired, neglected, improperly installed, abused, or otherwise damaged as has not been mentioned
above.
Copyright
© Copyright 1996 Simple Technology Inc., all rights reserved. No part of this publication may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form,
by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without expressed written
consent of STI.
Disclaimer
Specifications subject to change without notice. Simple Technology Inc. makes no representations or warranties with
respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any
particular purpose. Further, STI reserves the right to revise this publication and to make changes from time to time in the
content hereof without obligation of STI to notify any person of such revision.
Products and brand names are trademarks and/or registered trademarks of their respective companies.
Part Number 61000-00032-002 December 1996
Simple Technology Inc. • 3001 Daimler • Santa Ana, CA 92705 • (714) 476-1180
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

SimpleTech STI-105HD Quick Installation Manual

Taper
Quick Installation Manual
Ce manuel convient également à

dans d''autres langues