Candy CTPSC63/E1 Manuel utilisateur

Catégorie
Plaques de cuisson
Taper
Manuel utilisateur
PN:16166000A24993
Candy-MC-IT7251J1-AD CI633C/E1
80G双胶纸
20210301
1、印刷颜色:胶装,单黑;
EN-0
Instructions Manual For Induction Hob
ENGLISH
Thank you for purchasing the CANDY induction hob. Please read this instruction manual
carefully before using the hob and keep it in a safe place for future reference.
CTPSC63/E1
Manuel d'instructions pour plaque à induction
FRANÇAIS
59cm
52cm
6.2cm 5.8cm
5
4
6
4
5
1. On/Off c
ontrol
2. Flexible Area control
3. Boost
4. Heating zone selection controls
5. Keylock control
6. Timer control
four
1
2
3
1. Max. 1900/2000W zone
2. Max. 1900/2000W zone
3.
4.
Glass plate
5.
Control panel
6.
12 3
6
4
7. Power / Timer
slider touch control
7
How to use
Start cooking
Touch the ON/OFF control.
After power on, the buzzer beeps
once, all displays show “–” or “–”, indicating that the induction
hob has entered the state of standby mode.
Place a suitable pan on the cooking zone that you wish to use.
Make sure the bottom of the pan and the surface of the
cooking zone are clean and dry.
Touching the heating zone selection control, and an indicator
next to the key will flash
Select a heat setting by touching the slider control
If you don’t choose a heat setting within 1 minute, the
Induction hob will automatically switch off. You will need to
start again at step 1.
You can modify the heat setting at any time during
cooking.
If the display flashes alternately with the heat setting
This means that:
you have not placed a pan on the correct cooking zone or,
the pan you’re using is not suitable for induction cooking or,
the pan is too small or not properly centered on the cooking zone.
No heating takes place unless there is a suitable pan on the cooking zone.
The display will automatically disappear after 1 minute if no suitable pan is placed on it.
power up
power down
Finish cooking
Touching the heating zone selection control that you wish
to switch off
Turn the cooking zone off by touching the slider to “|”.
Make sure the displayshows”0”
Turn the whole cooktop off by touching the ON/OFF
control.
Beware of hot surfaces
H will show which cooking zone is hot to touch. It will
disappear when the surface has cooled down to a safe
temperature. It can also be used as an energy saving
function if you want to heat further pans, use the
hotplate that is still hot.
Using the Boost function
Activate the boost function
Touching the heating zone selection control.
Touching the boost control , the zone indicator show
“P” and the power reach Max.
Cancel the Boost function
Touching the heating zone selection control that you wish
to cancel the boost function
The function can work in any cooking zone.
The cooking zone returns to its original setting after 5 minutes.
If the original heat setting equals 0, it will return to 9 after 5 minutes.
FLEXIBLE AREA
This area can be used as a single zone or as two different zones, accordingly
to the cooking needs anytime.
• Free area is made of two independent inductors that can be controlled
separately.
As big zone
1.
To activate the free area as a single big zone, Touching the Flexible Area control .
2. As a big zone, we suggest the used as the follow:
Cookware: 250mm or 280mm diameter cookware (Square or Oval
cookware are acceptable)
We don’t recommend other operations except for above mentioned three
operations because it might effect the heating of appliance
As two independent zones
To use the flexible area as two different zones, you can have two choices of
heating.
(a) Put a pan on the right up side or the right down side
of the
flexible zone.
Touching the "Boost" control to cancel the Boost
function, then the cooking zone will revert to its original
setting.
(b)Put two pans on both sides
of the
flexible zone.
Notice: Make sure the pan is bigger than 12cm.
Locking the Controls
You can lock the controls to prevent unintended use (for example children accidentally turning the
cooking zones on).
When the controls are locked, all the controls except the ON/OFF control are disabled.
To lock the controls
Touch the lock control The timer indicator will show Lo
To unlock the controls
Touch and hold the lock control for a while.
When the hob is in the lock mode, all the controls are disable except the ON/OFF
,
you can always turn
the induction hob off with the ON/OFF control in an emergency, but you shall unlock the hob first in the
next operation.
Timer control
You can use the timer in two different ways:
a) You can use it as a minute minder. In this case, the timer will not turn any cooking zone off when the
set time is up.
b) You can set it to turn one or more cooking zones off after the set time is up.
The timer of maximum is 99 min.
a) Using the Timer as a Minute Minder
If you are not selecting any cooking zone
Make sure the cooktop is turned on.
Note: you can use the minute minder at least one zone shall
be active.
Touch timer control, the10will show in the timer display.
and the “0” flashes.
Set the time by touching the slider control. (e.g. 5)
Touch timer control again, the “1” will flash
Set the time by touching the slider control (e.g.9), now the
timer you set is 95 minutes.
When the time is set, it will begin to count down immediately. The display will show the remaining time
Buzzer will beep for 30 seconds and the timer
indicator shows “- -” when the setting time finished.
b) Setting the timer to turn one cooking zone off
Set one zone
Touching the heating zone selection control that you want to
set the timer for.
In short time, touch timer control, the10will show in the
timer display and the “0” flashes.
Set the time by touching the slider control. (e.g. 5)
Touch timer control again, the “1” will flash.
Set the time by touching the slider control (e.g.9), now the
timer you set is 95 minutes.
When the time is set, it will begin to count down immediately.
The display will show the remaining time .
NOTE: The red dot next to power level indicator will
illuminate indicating that zone is selected.
When cooking timer expires, the corresponding cooking zone
will be switched off automatically.
Other cooking zone will keep operating if they are turned on previously.
The pictures shown above are for reference only, and the final product shall prevail.
set more zones:
The steps for setting more zones are similar to the steps of setting one zone;
When you set the time for several cooking zones simultaneously, decimal dots of the relevant cooking
zones are on. The minute display shows the min. timer. The dot of the corresponding zone flashes.
The shown as below:
(set to 15 minutes)
(set to 45 minutes)
Once the countdown timer expires, the corresponding zone
will switch off. Then it will show the new min. timer and
the dot of corresponding zone will flash.
The shown as right:
(set to 30 minutes)
Touch the heating zone selection control, the corresponding timer will be shown in the timer indicator.
C)Cancel the timer
Touching the heating zone selection control that you want
to cancel the timer
Touching the timer control, the indicator flash
Touch the slider control to set the timer to “00”, the timer is cancelled
Default working times
Auto shut down is a safety protection function for your induction hob. It shut down automatically if ever
you forget to turn off your cooking. The default working times for various power levels are shown in the
below table:
Power level
1 2 3 4 5 6 7 8 9
Default working timer (hour)
8 8 8 4 4 4 2 2 2
When the pot is removed, the induction hob can stop heating immediately and the hob automatically
switch off after 2 minutes.
EN-14
You may have a number of different cooking vessels
1. This induction hob can identify a variety of cooking vessels, which you can test by
one of the following methods:
Place the vessel on the cooking zone. If the corresponding cooking zone displays a
power level, then the vessel is suitable. If “U” flashes, then the vessel is not
suitable for use with the induction hob.
2. Hold a magnet to the vessel. If the magnet is attracted to the vessel is suitable for
use with the induction hob.
NB: The base of the vessel must contain magnetic material.
It must have flat bottom with a diameter according to the table 1 below.
3. Use only ferromagnetic cookwares made from enameled steel, cast iron or stainless
steel but compatible with induction
4. Use pans whose diameter of the ferromagnetic area (base of the pan) is in the range
of dimensions in the table below. (Table 1)
- If you use smaller pots, performance could be affected
- If you use pot with a diameter smaller than the one indicated in the table 1, pots
may not be detected
According to the dimension of the zone you can use pots of different diameters as picture
below:
Iron oil frying
Stainless steel
Iron pan
Iron kettle
Enamel
stainless steel
kettle
Enamel cooking
utesil
Iron plate
5. If the ferromagnetic part covers only partially the base of the pan, only the
ferromagnetic area will heat up, the rest of the base may not heat up a sufficient
temperature for cooking.
6. If the ferromagnetic area is not homogeneous, but presents others material such as
aluminum this may affect the heating up and the pan detection.
If the base of the pan is similar to the pictures below the pan could be not detected.
The base diameter of induction cookware
Cooking zone
1 120
160
160
210
3
Minimum Maximum
The above may vary according to the size of the pan and the material it is made from.
2
180 290
EN-19
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40

Candy CTPSC63/E1 Manuel utilisateur

Catégorie
Plaques de cuisson
Taper
Manuel utilisateur

dans d''autres langues