Waterford JSAL15D Le manuel du propriétaire

Marque: Waterford

Modèle: JSAL15D

Catégorie: Accessoires de piscine hors terre

Taper: Le manuel du propriétaire

Ce manuel convient également à

WATERFORD SYSTEMS

HIGH RATE SAND FILTER SYSTEM

For Above Ground Swimming Pools

O W N E R ’ S M A N U A L

INSTALLATION, OPERATION & PARTS

Sta-Rite Pool/Spa Group

293 Wright Street, Delavan, WI 53115

International: 262-728-5551, FAX: 262-728-7550

www.starite.com

Union City, TN • Delavan, WI • Mississauga, ON

S260 (Rev. 4/26/06)

839 0494

Models

15" Tank 18" Tank 21" Tank

3/4 HP JSAL15D JSAL180D JSAL210D

1 HP JSAL15E JSAL180E JSAL210E

1 HP (2-Speed) JSAL180E JSAL210E

1-1/2 HP JSAL180F JSAL210F

This manual should be furnished to the end user

of this system; its use will reduce service calls and

chance of injury and will lengthen system life.

entair P

ool Pr

oducts,

Inc.

1620 Ha

wkins Ave.

Sanf

ord, NC 27330

Tel 919-774-4151 • Fax 919-774-4841

S260 (Re

B 6/28/06)

HIGH-RATE SAND FILTER SYSTEM

To avoid unneeded service calls, prevent possible injuries, and get the most out

of your filter, READ THIS MANUAL CAREFULLY!

The High Rate Sand Filter System:

• Is designed to circulate and filter water in above ground swimming pools.

• Offers quiet, efficient performance and is durable, reliable.

• With a 3’ cord or no cord, use with permanently installed pools ONLY

(see CAUTION #7, below).

• With a 25’ cord, use with storable pools ONLY (see CAUTION #8, below).

Table of Contents

Safety Instructions.......................................................................................................3

Specifications/Dimensional Data...............................................................................4

General Information..................................................................................................5

Installation.............................................................................................................5-7

Filter Mount/Piping ................................................................................................5

Filter Set-up ...........................................................................................................6

Loading Sand Media ..............................................................................................6

Valve Installation................................................................................................6-7

Electrical ..................................................................................................................7

Startup/Operation/Backwash..................................................................................8-9

Maintenance.............................................................................................................9

Storage/Winterizing ................................................................................................10

Multi-Port Valve Service .........................................................................................11

Valve Removal .......................................................................................................11

Pump Service ....................................................................................................11-12

Troubleshooting Guide ...........................................................................................13

Repair Parts List .................................................................................................14-17

Warranty ................................................................................................................18

IMPORTANT SAFETY INSTRUCTIONS

When installing and using electrical equipment, basic safety precautions should always be followed,

including the following:

SAVE THESE INSTRUCTIONS

1. READ AND FOLLOW ALL SAFETY INSTRUCTIONS.

2. To reduce the risk of injury, do not permit

children to use this product unless they are closely super-

vised at all times.

3. Risk of electrical shock. Connect only to a

grounding type receptacle protected by a ground-fault cir-

cuit-interrupter (GFCI). Contact a qualified electrician if you

cannot verify that the receptacle is protected by a GFCI.

4. Do not bury cord. Locate cord to minimize abuse from

lawn mowers, hedge trimmers, and other equipment.

5. To reduce the risk of electrical shock,

replace a damaged cord immediately.

To reduce the risk of electrical shock, do

not use an extension cord to connect unit to electrical sup-

ply; provide a properly located outlet.

7. Permanent pumps are for use with perma-

nently installed pools and may also be used with hot tubs

and spas if so marked. Do not use with storable pools. A

permanently installed pool is constructed in or on the

ground or in a building such that it cannot be readily dis-

assembled for storage. A storable pool is constructed so that

it may be readily disassembled for storage and reassembled

to its original integrity.

8. Storable pool pumps are for use with

storable pools only. Do not use with permanently installed

pools. A storable pool is constructed so that it is capable

of being readily disassembled for storage and reassembled

to its original integrity. A permanently installed pool is

constructed in or on the ground, or in a building, such that

it cannot be readily disassembled for storage.

This is the safety-alert symbol. When you see

this symbol on your valve or in this manual, look

for one of the following signal words and be alert to

the potential for personal injury.

warns about hazards that will cause se-

rious personal injury, death or major property damage

if ignored.

warns about hazards that can cause seri-

ous personal injury, death or major property damage

if ignored.

warns about hazards that will or can

cause minor personal injury or property damage if

ignored.

The label NOTICE indicates special instructions

which are important but not related to hazards.

Carefully read and follow all safety instructions in

this manual and on system.

Keep safety labels in good condition.

Replace missing or damaged safety labels.

Incorrectly installed or tested equip-

ment may fail, causing severe injury or

property damage. Read and follow in-

structions in owner's manual when installing and op-

erating equipment. Have a trained pool professional

perform all pressure tests.

1. Do not connect system to a high pressure or city

water system.

. Use equipment only in a pool or spa installation.

3. Trapped air in system can cause explosion. BE

SURE all air is out of system before operating or

testing equipment.

Before pressure testing, make the following safety

checks:

• Check all clamps, bolts, lids, and system accessories

before testing.

• BE SURE all air is out of system before testing.

• Tighten Sta-Rite trap lids to 30 ft. lbs. (4.1 kg-cm)

torque for testing.

• Water pressure for test must be less than 25 PSI

(172 kPa).

• Water temperature for test must be less than 95˚ F.

(35˚ C).

• Limit test to 24 hours. After test, visually check sys-

tem to be sure it is ready for operation. Remove trap

lid and retighten hand tight only.

NOTICE: These parameters apply to Sta-Rite equip-

ment only. For non-Sta-Rite equipment, consult

manufacturer.

Hazardous Pressure!

Can cause tank

explosion.

WHEN USING SYSTEM:

Do not test with

compressed air

or operate above

rated pressure.

Hazardous voltage.

Can shock, burn,

or cause death.

BEFORE WORKING

ON PUMP OR MOTOR:

Unplug pump motor.

Hazardous suction.

Can trap or tear

hair or body parts,

causing severe injury

or death.

WHEN USING SYSTEM:

Do not block pump

suction or pool main

drain.

READ AND FOLLOW SAFETY INSTRUCTIONS!

1-1/2" NPT

Return to Pool

(Union Connection)

1-1/2" NPT

Suction

Connection

1-1/2" NPT

Waste Outlet

(Union Connection)

2-13/16

1278 0994

Drain

(To Tank

Flange)

2-5/16

9-1/16

11-1/4

Tank

Dia.

1279 0994

TABLE I - OUTLINE DIMENSIONS IN INCHES (mm)

Filter Model A B C D E

15”(406mm) Filters 24 (610) 30-7/8 (784) 15-3/4 (400) 21-11/16 (551) 26-1/16 (662)

18”(457mm) Filters 26-9/16 (675) 33-5/16 (846) 17-3/4 (451) 24-1/4 (616) 27-1/16 (692)

21” (508mm) Filters 28-11/16 (729) 34-7/16 (875) 20-3/4 (527) 26-3/8 (670) 28-9/16 (725)

TABLE ll - FILTER SPECIFICATIONS AND OPERATING INFORMATION

FILTER MODEL: 15” 18” 21”

(JSAL15 Series) (JSAL180 Series) (JSAL210 Series)

Effective Filter Area 1.26 Ft.

(.117M

) 1.57 Ft.

(.223M

) 2.18 Ft.

(.203M

)

Max. Flow Rate 25.2 GPM(95 L/m) 31.5 GPM(123 L/m) 43.6 GPM(165 L/m)

Max. Operating Pressure 50 PSI(345 kPa) 50 PSI(345 kPa) 50 PSI(345 kPa)

ax. Operating Temperature 95° F(35°C) 95° F(35°C) 95° F(35°C)

Turnover in Hours:

6 Hours 9,070 Gal.(34 330 liters) 11,340 Gal.(42 922 liters) 15,700 Gal.(59 424 liters)

8 Hours 12,100 Gal.(45 799 liters) 15,120 Gal.(57 229 liters) 20,930 Gal.(79 220 liters)

10 Hours 15,120 Gal.(57 229 liters) 18,900 Gal.(71 536 liters) 26,160 Gal.(99 016 liters)

12 Hours 18,144 Gal.(68 675 liters) 22,680 Gal.(85 844 liters) 31,390 Gal.(118 811 liters)

Qty. of Media Required:

Cu. Ft. (cm

) 1(28 320cm

) 1.5(42 255cm

) 2(56 923cm

)

Weight in lbs.(kg) 100(45,4 kg) 150(68 kg) 200(90,7 kg)

NOTE: 1 cubic foot (28 320 cm

) of sand weighs approximately 100 lbs. (45,4kg). DO NOT use a finer grade of sand than recommended.

RECOMMENDED SAND GRADES:

Use only: #20 Silica Sand, Size Range .40-.55mm., Uniformity Coefficient less than 1.75.

NOTICE: Use of other sands will reduce filter performance, may damage pump, and will void warranty.

Recommended:

1. Wedron Silica/Best Sand Co., Sand Grade: Wedron .45-.55mm., Effective Size .46mm, Uniformity Coefficient 1.22.

2. U.S. Silica - Silurian Filter Sand, Sand Grade.45-.55 mm., Effective Size .48mm, Uniformity Coefficient 1.18.

Figure 1: Dimensions

GENERAL INFORMATION

• Clean a new pool as well as possible before filling

pool and operating filter. Excess dirt and large particles

of foreign matter in the system can cause serious dam-

age to the filter and pump.

NEVER test this filter with compressed air.

Do not operate filter at water temperatures above

95°F (35°C).

NEVER operate this filter system at more than 50

pounds per square inch (50 PSI/345 kPa) pressure!

Plug system into electrically isolated, Ground Fault

Circuit Interrupter protected circuit ONLY!

• Clean a new pool as well as possible before filling

pool and operating filter. Excess dirt and large particles

of foreign matter in the system can cause serious dam-

age to the filter and pump.

• Keep pool water pH at recommended level (7.2 to 7.6)

to avoid irritation to eyes and skin.

• The Hi-Rate Sand Filter System is designed for use

with above ground swimming pools only.

• Use only #20 Silica sand with a screen mesh of .45

to .55mm. Use of other sands will reduce filter

performance.

To reduce risk of electric shock, install

pump at least 10 feet from the inside wall of the pool.

Do not use an extension cord.

INSTALLATION

Trap to Pump Assembly:

Using four 5/16” cap screws, flat washers and lockwashers,

mount trap to pump body; be sure to install gasket between

trap and pump body. Tighten cap screws to 80 inch-lbs

(92 cm-kg) torque; do not overtighten.

Filter Mount Must:

• Provide weather and freezing protection.

• Provide space and lighting for easy access for routine

maintenance. (See Table I and Figure 1, Page 4, for

space requirements.)

• Be on a reasonably level surface and provide adequate

drainage.

• Be as close to pool as possible to reduce line loss from

pipe friction.

• Be solid – level– rigid – vibration free.

• Be installed so that trap suction inlet is below pool

water level at all times. This allows pump to prime.

• Have adequate ventilation to prevent motor

overheating.

Piping:

• Use teflon tape or Plasto-Joint Stik

on all male con-

nections of plastic pipe and fittings except unions. DO

NOT use pipe compounds on plastic pipe; it will

cause the pipe to crack. Do not use sealant or tape on

nions – assemble them dry and hand tight.

• Do not damage union sealing surfaces and “O” Rings.

• Support pipe independently to prevent strains on filter

and valve.

• Use 1-1/2 or 2" pipe to reduce pressure losses as much

as possible. If flex hose is used, use the type with

smooth internal walls.

• Fittings restrict flow; for best efficiency use fewest pos-

sible fittings.

• Keep piping tight and free of leaks: pump suction line

leaks may cause trapped air in filter tank or loss of

prime at pump; pump discharge line leaks may show

up as dampness or jets of water.

• When unions are provided, use as follows for leak free

connections:

1. O-Ring and sealing surfaces must be clean.

2. Assemble hand tight only (no wrenches).

3. No pipe compound or teflon tape on unions.

Valves:

• For servicing filter system and for cleaning pump trap,

install ball or gate valves

A. Between pump trap and pool skimmer, and

B. Between selector valve and return pipe to pool.

• A check valve installed between filter and heater will

prevent hot water from backing up into filter and de-

forming internal components.

• Use care before assembly not to damage union sealing

surfaces or O Ring.

Wastewater:

• Be sure all provisions for waste water disposal meet

applicable local, state or national codes. 100 gallons

(379 liters) or more of pool water will be discharged

during filter backwashing. Do not discharge where

water will cause flooding or damage.

Lake Chemical Co., Chicago, IL

Filter Setup

Assembly: See Figures 2 through 5 for filter assembly.

Loading Sand Media

1. To keep sand out of collector assembly, place plastic

and shield over top of collector tube before pouring

sand into filter (See Figure 5).

2. To support laterals and prevent lateral breakage dur-

ing loading, fill tank about half full of water before

loading sand.

3. Pour sand into filter tank. See “Recommended Sand

Grades”, Page 4, for correct type and quantity of sand

to use.

NOTICE: Make sure gasket area on top of tank is free

of sand before installing valve and clamp.

4. Before installing valve, double-check that correct

quantity of sand has been loaded (see Page 4).

5. Remove plastic sand loading shield and keep for fu-

ture use.

Valve Installation:

See Figures 6, 7, and 8

1. Install O-Ring on valve flange; make sure O-Ring is

clean, dry, and has no nicks, tears, or scrapes.

2. Make sure tank and valve flanges are clean and free of

sand; put valve on top of tank. Vertical pipe of collec-

tor assembly inserts into base of valve.

3. Install clamp; make sure knob is positioned for easy

access for filter maintenance. Valve port labeled

“

PUMP” should point toward pump.

. Tighten clamp knob until clamp ends (under bolt) are

1/4" (6mm) apart. Tap around outside of clamp with a

mallet to help seat clamp.

Hazardous pressure. Clamp will not

hold unless it is seated properly! DO NOT START

PUMP until clamp ends are 1/4" (6mm) apart or less.

5. If clamp will not pull up to 1/4" (6mm) gap, wait

15-30 minutes and retighten. Tap clamp gently with

mallet to help seat clamp.

6. Connect pipe from pump discharge to valve port la-

beled “PUMP”; use union half provided. Assemble

union as follows for leakfree operation:

A. O-Ring and sealing surfaces must be clean.

B. Assemble hand tight only (no wrenches).

C. NO pipe compound or teflon tape on unions.

7. Complete all plumbing connections (see Page 5 for

piping requirements).

A. Pipe from valve RETURN port to pool return.

B. Pipe from valve WASTE port to waste.

C. Suction piping from pool to trap inlet on pump.

B. Insert assembly

into top of

filter tank.

A. Insert first lateral into socket;

twist clockwise 1/4 turn

to lock lateral into hub.

Lateral is correctly installed

when slots face down.

731 0294

C. Hold assembly up

near top of tank and

add remaining

laterals.

732 0294

D. After all

laterals are

securely in

sockets,

position

assembly on

centering

boss in

bottom of

tank.

733 0294

::::

Fill tank

about

half full

of water

before

adding

sand.

Sand Shield

keeps collector

hub assembly

clean when

loading filter.

734 0294

Figure 2

Figure 3

Figure 4

Figure 5

8. System is ready for startup.

NOTICE: If there are leaks from beneath valve/clamp

area, STOP PUMP, release all pressure, remove clamp

and valve and clean sealing surfaces.

Follow directions under “Valve Installation”, Page 6,

when reinstalling valve. See Figures 6 and 7.

ELECTRICAL

Risk of electrical shock.

Plug pump into a

grounded, GFCI-protected 115

Volt circuit only. Incorrect volt-

age can cause fire or seriously

damage motor and voids war-

ranty. Protect cord from water

and physical damage.

GFCI tripping indicates

an electrical problem. If

GFCI trips and will not reset,

have a qualified electrician in-

spect and repair electrical sys-

tem.

Risk of electrical

shock. Unplug motor before

servicing or repairing pump or

motor.

Wiring:

Install a Ground Fault Circuit Interrupter (GFCI) in cir-

cuit; it will sense a short-circuit to ground and discon-

nect power before it becomes dangerous to pool users.

For size of GFCI required and test procedures for GFCI,

see manufacturer’s instruction.

In case of power outage, check GFCI for tripping (which

will prevent normal water circulation). Reset if necessary.

Match circuit breaker size to Table III, Page 8.

• Do not modify cord, plug, or receptacle. If an existing

circuit must be used and the receptacle and plug do

not match exactly, consult a licensed electrician.

• Do not use an extension or drop cord with this system;

it could cause a fire hazard or low voltage problems.

Wet cords cause shock hazards. Extension cords can

easily become cut or frayed and dangerous when

placed across yard areas or walkways.

Voltage:

Voltage at motor must be not more than 10% above or

below motor nameplate rated voltage or motor may

overheat, causing overload tripping and reduced compo-

nent life. If voltage is less than 90% or more than 110%

of rated voltage when motor is running at full load, con-

sult power company.

1. Install O-Ring

on valve flange.

2. Install valve on tank.

Tank flange must

be clean; insert

collector pipe

into bottom

of valve.

Delavan, WI.

53115

USA

1/4" Max.

Port labeled

"PUMP" should

point toward

pump.

Install clamp

and tighten

until clamp

ends (under

bolt) are 1/4"

apart.

If unable to

close gap

to 1/4" or less,

wait 15-30

minutes and

retighten.

Tap around

clamp while

tightening to

help seat

clamp.

.WATERFORD, WI.

53185

736 0294

Figure 6

Figure 7

Hazardous voltage.

Can shock, burn,

or cause death.

Disconnect power

before working

on pump or motor.

Table III–Recommended Fusing Data, 115 Volt 60 Hz Motors.

ranch

Pump Motor Full Load Circuit Breaker

odel No. H.P. Amps Rating (Amps)

JWPA5DC-2A3 3/4 9.4 15

JWPA5EC-2A3 1 11.9 15

WPS5FC-2A3 1-1/2SPL 11.9 15

7290-J1002 (2-Speed) 1 – 1/6 11.6/3.3 15

NOTICE: Values given are for pump motor only. Do not put

any other accessories on this circuit.

Table IV–Recommended Fusing Data, 115 Volt 60 Hz Single

Speed Motors.

Branch

Pump Motor Full Load Circuit Breaker

Model No. H.P. Amps Rating (Amps)

ABGS4EL-A2 1SPL 9.0 15

JWPA5DL-2A1, -2A2 3/4 9.0 15

JWPS5EL-A2 1SPL 9.0 15

JWPA5EL-2A1, -2A2 1 12.0 15

JWPAS5F-2A4U 1-1/2 SPL 12.0 15

JWPS5FL-A2 1-1/2 SPL 12.0 15

JWPA5FL-2A1, -2A2 1-1/2 16.0 20

Table V–Recommended Fusing Data, 230 Volt 60 Hz Motors.

Branch

Pump Motor Full Load Circuit Breaker

Model No. H.P. Amps Rating (Amps)

JWPA5E-230A2 1 6.1 15

Table VI–Recommended Fusing Data, 115 Volt 60 Hz 2-Speed

Motors.

Branch

Pump Motor Full Load Circuit Breaker

Model No. H.P. Amps Rating (Amps)

JWPA5YEL 1 / 1/8 11.7/3.39 15

JWPA5YFL 1-1/2 / 1/6 16.6/3.6 25

NOTICE Values given are for pump motor only. Do not put any

other accessories on this circuit.

Startup/Operation

(

See Figure 9)

Hazardous suction. Can trap and tear hair

or body parts and can cause drowning. Do not block

pump suction. Small children using pool must ALWAYS

ave close adult supervision.

Valve Setting

urpose/Flow

FILTER

Normal filtration and

acuuming; water goes

hrough filter to pool.

RINSE

or initial startup cleaning

and sand bed leveling

after backwash; water goes

through filter to waste.

RECIRCULATE

Circulates pool water;

bypasses filter.

737 0294

BACKWASH

Reverses flow for

cleaning; water

goes through filter

to waste.

CLOSED

Shuts off all flow to

filter and pool.

WINTERIZE

Leaves all valve ports

partially open for

winter storage.

Valve Setting

Purpose/Flow

738 0294

Figure 8

3/4 and 1 HP Models with

–A2 suffix use15-amp

straight outlet, above.

1-1/2 HP Models with

–2A2 suffix use 20-amp

straight outlet, above.

All models with –A1 or

–2A1 suffix use 20-amp

twist-lock outlet, above.

NOTICE: Determine circuit breaker rating from Table III, above.

Determine correct outlet required from illustration below.

“ABG” and “JWP” 3/4 and 1 HP

Models with A2,

-2A2 and -A2U suffix and

1-1/2 HP Models with -2A4U

suffix use 15-amp straight

outlet, above.

“ABG” and “JWP” 1-1/2 HP

Models with A2,

-2A2 and A2U suffix use

20-amp straight outlet, above.

All “ABG” and “JWP” Models

with A2, -2A1 suffix use 20-amp

twist-lock outlet, above.

Hazardous pressure. To avoid explosion

nd possible severe or fatal injury, filter system pressure

ust not exceed 50 PSI (345 kPa) under any circum-

stances. NEVER test this filter system with compressed

air; never operate system with water temperature above

95° F (35° C).

To prevent equipment damage and possible

injury, turn pump OFF before changing valve position.

NOTICE: Do not add chemicals directly into the pool

skimmer. Adding undiluted chemicals may damage

equipment and void warranty.

1. Open system valves and make sure pump is filled

with water.

Make sure pool water level is above skimmer or the

suction outlet.

2. With pump OFF, set valve to ‘BACKWASH’ position.

3. Start pump, circulating water backwards through fil-

ter to waste.

4. Backwash until water runs clear (3-5 minutes).

5. Stop pump; set valve to ‘RINSE’ position.

6. Start pump; run pump for one minute.

7. Stop pump; set valve to ‘FILTER’ position.

8. Filter is now ready for service.

9. Record clean starting filter pressure gage reading as a

reference.

10. When pool is first filled, backwash once a day until

pool water is sparkling clear. After that, backwash

when pressure gage shows 5 to 7 PSI (34.5 to 48

kPa) higher than starting pressure.

MAINTENANCE

General:

•

Wash outside of filter with a mild detergent and water.

inse off with hose.

NOTICE: DO NOT use solvents to clean filter; solvents

may damage plastic components in system.

• Inspect sand bed at least once a year to remove for-

eign material which has not been backwashed out of

system.

NOTICE: When the sand bed gets hard and crusty on

top, remove all the old sand and replace it with new

sand.

Weekly Pool Equipment Inspection:

1. Check pressure during operation. When pressure is 5

to 7 PSI (34.5 to 48 kPa) higher than initial operating

pressure, backwash filter (see instructions under

“Startup/Operation”).

2. Except during hot weather with heavy swimmer loads,

operating filter 6 to 12 hours per day should be suffi-

cient. Carefully monitor water chemical balance and fol-

low recommendations of your local pool professional.

Water Maintenance

• Keep water level at least two inches above bottom of

skimmer opening when system is not in operation.

Failure to do so can allow air to enter system, causing

pump to lose prime and filter to entrap air.

• Maintain pH at 7.2 to 7.6 in pool.

To prevent damage to system components, keep

water temperature below 95° F (35° C) at all times.

Vacuum Pool:

1. Fill vacuum hose by submerging in water from one

end to the other.

2. To vacuum, insert hose into skimmer suction manifold

or into vacuum line in pool wall. See instructions pro-

vided by pool builder or pool manufacturer. Start

pump, making sure it is primed and pumping.

3. After vacuuming, clean pump trap to remove accumu-

lated debris, then check filter pressure gage. If reading

is 5 to 7 PSI (34.5 to 48 kPa) higher than initial oper-

ating pressure, backwash filter

Lower or Drain Pool

(See Figure 10, Page 10)

1. Turn pump ‘OFF’; set valve handle to ‘WASTE’.

2. Use vacuum cleaner hose and head.

3. Start pump; run until pool is lowered to desired level.

4. Turn pump ‘OFF’; set valve handle to ‘FILTER’.

5. Start pump.

Figure 9: Valve settings for startup. Stop

pump before changing valve position.

WASTE

Lowers pool level or

drains pool; water

bypasses filter,

goes to waste.

Valve Setting

Purpose/Flow

743 0294

STORAGE/

WINTERIZING

ool chemicals may give off corrosive

umes. Store chemicals away from system in a well ven-

tilated area.

NOTICE: Allowing water to freeze will damage filter and

void warranty. If antifreeze is needed, use propylene glycol;

it’s plastic compatible and non-toxic. Follow manufacturers

instructions. Do not use ethylene glycol based anti-freeze –

it’s toxic and it may damage plastic components.

1. Open all system valves. Set multiport valve at ‘WIN-

TERIZE’ to allow air passage to all ports (Figure 11).

2. Remove drain plug from filter.

3. Drain filter tank completely and replace drain cap

(Figure 12).

4. Cover with plastic or tarpaulin to protect from

weather.

5. Remove drain plugs from pump.

6. Protect from freezing.

Startup for Winterized Equipment:

1. Remove any temporary weather protection placed

around system for shutdown.

2. See “Startup”, Page 8, for reactivation of the filter.

3. Inspect all electrical wiring to pump for damage or

deterioration over the shutdown period. Have a quali-

fied serviceman repair/replace wiring as needed.

Inspect and tighten all watertight connections.

4. Open all valves in suction and return piping.

5. Remove any winterizing plugs in system.

6. Drain all winterizing chemicals (if used) from system;

flush system.

7. Close all drain valves and replace all drain plugs in

system.

8. Fill pool with water to proper level (see pool maufac-

turer’s instructions).

Drain Fitting Installation/Removal

NOTICE: If pool is above height of filter, first close

valves in pump suction and return lines to prevent drain-

ing pool. If there are no shutoff valves installed, discon-

nect suction and return lines and raise ends above pool

ater level.

1. Installation: See Figure 12.

2. To Drain Filter:

A. Remove drain cap. Lateral tube should remain in

place inside drain opening to prevent sand from

draining out.

B. Open union coupling on backwash port of Multi-

Port valve. This will allow air into filter and allow

water to drain from filter tank.

C. Replace cap when tank is empty.

3. Removing Sand From Filter:

A. Remove both drain cap and slotted lateral tube (see

Figure 12). Sand and water will drain from tank.

B. To completely flush filter tank of sand, remove top

clamp and multiport valve and flush the inside of

the tank with a hose.

C. Thoroughly clean sand from all parts and from tank

drain opening before reassembling drain fitting.

Figure 10: Valve settings to lower pool water level.

Stop pump before changing valve position.

Figure 11: Valve setting for winter storage.

Stop pump before changing valve position.

About 1"

Small

O-Ring

Open end

of lateral

Seat small

O-Ring

Large

O-Ring

End of lateral is

flush with end of

drain fitting

746 0294

Figure 12: Drain Fitting Assembly. This assembly al-

lows water to drain without losing the sand out of

the filter tank.

Make sure all surfaces are clean and free of sand.

Don’t cross thread cap; don’t overtighten cap.

MULTI-PORT VALVE SERVICE

Hazardous pressure. Stop pump and re-

lease all pressure from system before working on filter,

valve, or clamp.

NOTICE: If Multi-Port valve is below pool water level,

close suction and discharge valves before disassembly to

prevent draining pool.

Handle Replacement:

1. Stop pump.

2. Place handle in ‘FILTER’ position.

3. Remove pin (Key 1, Figure 13) to disconnect handle. If

it cannot be removed by hand, use a hammer and cen-

ter punch and lightly tap it out.

4. Remove handle; replace with a new one. Be sure new

handle is in ‘FILTER’ position.

5. Replace pin.

Lid and Plug replacement:

A. Remove Handle (see ‘Handle Replacement’, above).

B. Remove plug:

1. Remove all screws and nuts (Key Nos. 2 and 6,

Figure 13).

2. Remove lid (Key No. 3) by pulling straight up while

holding plug shaft (Key No. 5) down with thumb.

C. Inspect Internal Parts:

Inspect plug and gasket spring, O-Rings, and internal

washers (Key No. 4). Replace if necessary.

D. Reassemble Valve:

1. Replace plug gasket and shaft, mounting spring,

washers, and O-Ring on plug shaft. Lubricate O-

Ring with Amojel.

2. Replace lid; match screw holes in lid and body.

3. Press down on lid to allow screws to engage nuts;

tighten each nut securely.

4. Replace top washer (Key No. 1A) and handle, mak-

ing sure indexing pin on plug shaft points in same

direction as pointer on handle. Replace handle pin.

5. Tighten all lid screws to 55 inch-lbs. (63.4 kg-cm)

torque.

Valve Removal

Hazardous pressure. Stop pump and re-

lease all pressure from system before working on filter,

valve, or clamp.

NOTICE: If multi-Port Valve is below pool water level,

close suction and discharge valves before disassembly to

prevent draining pool.

1. Disconnect piping from pump and pool.

2. Remove clamp.

. Remove valve from filter top.

4. To reinstall valve, follow “Valve installation” instruc-

ions, Page 6. BE SURE to follow clamp tightening in-

tructions.

PUMP SERVICE

To protect against possible electric shock,

use only identical replacement parts when servicing.

System should only be serviced by qualified personnel.

Before removing trap cover:

1. STOP PUMP before proceeding.

2. CLOSE GATE VALVES in suction and discharge pipes.

3. RELEASE ALL PRESSURE from pump and piping

system.

Aquatools

WATERFORD, WI.

3185

744 0294

Figure 13: Valve Disassembly

To avoid dangerous or fatal electrical shock haz-

rd, turn OFF power to motor before working on

ump or motor.

Trap needs no lubrication or regular maintenance be-

ond reasonable care and periodic cleaning of strainer

basket.

If shaft seal is worn or damaged, repair as follows:

Pump Disassembly:

1.Unplug motor before servicing or repairing pump or

motor.

2.Close all valves in suction and discharge piping.

3.Remove drain plugs from the bottom of pump and

trap; drain pump completely.

4.Disconnect pipe unions (or clamps) on suction and

discharge piping. Remove hold down bolts and with-

draw complete pump/motor/trap assembly.

5.Remove cap screws (Key No. 16, Pages 15 and 16)

from front plate (Key No. 13). Remove front plate

with trap (Key No. 20) attached. Remove and inspect

O-Ring (Key No. 12).

6.Remove end cap (Key No. 2) from motor cover (Key

No. 7). NOTICE: JWP Series pump motors do not

have a motor cover or switch.

7.Hold motor shaft with 7/16” wrench on flats on

motor shaft; unscrew impeller (Key No. 11).

8.Carefully remove rotating half of seal (Key No. 10)

from impeller sleeve. Twist as you pull; make sure

you do not damage surface of sleeve where seal both

seats and seals. See Figure 14.

9.Remove motor throughbolts (see Figure 15). Remove

seal plate (Key No. 9). Tap stationary half of seal out

of seal plate (see Figure 16).

10. If necessary, disconnect electrical wiring from motor

terminal board and remove motor (Key No. 6) from

motor cover (Key No. 7).

Pump Assembly:

1. Examine seal cup and O-Rings. Replace anything that

shows signs of wear or damage.

2. Check the shaft seal (Key No. 10, Pages 15 and 16)

for scoring, scratches, chips, etc., and for any signs of

damage to spring or retainer. Replace if any wear or

damage is visible.

3.Press stationary half of seal into seal plate (Key No. 9)

using finger pressure only (see Figure 17). Make sure

eal is firmly and evenly seated.

4.Install rotating half of seal on impeller sleeve. Push it

onto sleeve until it butts against back of impeller.

5.Insert impeller sleeve through center hole in seal

plate (Key No. 9). Thread slinger (Key No. 8) over the

end of the impeller sleeve.

6.If motor has been removed from motor cover, rein-

stall it now. Set up seal plate (Key No. 9) in front of

motor cover; hold motor shaft with 7/16” wrench on

shaft flats (under cap) and thread impeller through

center hole in seal plate onto shaft). Make sure that

slinger is in place on impeller sleeve – not loose on

shaft.

7.Install motor throughbolts; make sure seal plate butts

firmly against motor endbell. If necessary, install

motor cover and switch.

8.Install wear ring on back of front plate.

NOTICE: Teeth on wear ring interlock with ribs in

front plate.

9.Install front plate (Key No. 13). Tighten cap screws in

sequence as shown in Figure 18; tighten to 30 inch-

lbs. (34.5 cm-kg.) torque.

10.Reinstall drain plugs; reinstall pump and motor on

base and tighten hold-down bolts.

11. Reconnect unions; tighten hand tight only.

Figure 14 Figure 15 Figure 16 Figure 17

#5 #3

Start

Here

Figure 18: Pump front Plate Torque Sequence.

TROUBLESHOOTING

GUIDE – PUMP

Read and understand safety and operating instruc-

tions in this manual before doing any work on

pump.

A. Pump does not operate:

1. Check GFCI (Ground Fault Circuit Interrupter) for

proper operation according to GFCI manufac-

turer’s instructions.

2. Check for blown fuses, circuit breakers, or discon-

nected electrical wiring.

3. Check for sand locked impeller. Disconnect power

to motor; follow “Pump Disassembly” instructions,

Page 12. Clean out sand from impeller and from

wear ring in front plate. Reassemble according to

instructions, Page 12.

4. Consult dealer/installer or service representative.

B. Motor runs, but does not pump water or pressurize

system:

1. Check to make sure all valves are open.

2. Check skimmer, trap basket, and piping for debris

or obstructions.

3. Check pump impeller for obstructions such as

hair, leaves, grass, or stones. Follow “Pump

Disassembly” instructions, under “Pump Service”

on Page 12.

4. Consult with dealer/installer or service

representative.

C. Excessive air in system – pump loses prime:

1. Make sure water level in skimmer is at least 2”

above bottom of skimmer throat with system not

operating.

2. Make sure that there are no leaves in suction

piping.

3. Make sure there is no vortex (whirlpool) at the

suction; add water to pool if necessary.

4. Consult dealer/installer or service representative.

D. Circuit breaker in home panel trips repeatedly:

1. Breaker must be of adequate capacity.

2. If breaker is a GFCI breaker, test according to

GFCI manufacturer’s instructions.

3. Be sure no other lights and appliances are on cir-

cuit.

4. Check wiring size leading to pump. Inadequate

size wiring will cause overheating of pump and

excessive amp draw leading to circuit breaker

tripping.

5. Consult dealer/installer or service representative

TROUBLESHOOTING

GUIDE – FILTER

A. Short Cycle between backwashes:

OTICE: Time between backwashes will vary with each

installation and between different areas of the country.

Ask installer about normal backwash interval in your

area. The following causes and remedies are for cycle

times shorter than normal for your area.

1. Flow rate too high or filter too small; consult dealer

for system sizing recommendations.

2. Water is chemically out of balance; consult pool

serviceman.

3. Excess dirt/dust in pool; vacuum pool directly to

waste.

4. Body oil/lotion build-up in filter; consult dealer for

chemical filter cleaners and follow cleaner manu-

facturer’s instructions.

5. Filter inadequately backwashed. See instructions

under “Startup/Operation”, Page 8.

6. Algae in pool. Consult pool professional about

proper chemical maintenance.

7. Residual chlorine level too low. Consult pool pro-

fessional about proper chemical maintenance.

8. Inspect filter sand for solidification caused by dust,

calcium, skin oils, of suntan lotions.

B. Low Flow:

1. Pipe blocked downstream from filter; remove ob-

struction.

2. Piping too small; use larger pipe (consult dealer for

sizing).

3. Plugged pump; plugged hair and lint trap or skim-

mer basket. Clean thoroughly.

C. Pool Water Not Clear:

1. Water is chemically out of balance; consult pool

professional.

2. Filter is too small; consult dealer about equipment

sizing.

3. Sand in pool means broken lateral. Drain both

water and sand out of tank. Remove valve; follow

procedure under “Filter Setup”, Page 6, and in-

structions with new lateral to replace broken part.

To avoid severe injury or major property

damage, follow instructions under 'Valve Installation',

Figures 6, 7 and 8, Pages 6, 7 and 8).

1. Follow “Valve Removal” procedure, Page 11.

2. Replace lateral according to instructions supplied

with new lateral.

3. Reassemble filter according to instructions under

“Filter Setup”, Page 6

MODELS

JSAL180D JSAL210D

JSAL180E JSAL210E

JSAL15D JSAL180E JSAL210E

JSAL15E JSALS180E JSAL210F

Key No. JSALS15E JSAL180F JSALS210F

No. Part Description Used

15” Filter 18” Filter 21” Filter

1 Pump* (Models with -06, -09 suffix) 1 JWP Series JWP Series JWP Series

1 Pump** (All other suffixes) 1 JWP Series JWP Series JWP Series

1 Pump+ (“ABG” Series) 1 “ABG” Series “ABG” Series “ABG” Series

2 O-Ring 2 U9-226 U9-226 U9-226

3 Hose Assembly (Includes Key No. 2) 1 24203-0036 24203-0033 24203-0034

4A Hose Adapter 2 11201-0002 11201-0002 11201-0002

4B Sight Glass 1 14962-0012 14962-0012 14962-0012

5 Multiport Valve** (Includes Key Nos. 6, 7 and 16) 1 WC112-148A WC112-148A WC112-148A

6 O-Ring, Tank Flange 1 U9-369 U9-369 U9-369

7 V-Clamp with Knob 1 WC119-87A WC119-87A WC119-87A

8 Pedestal Platform 1 24201-0055P 24201-0055P 24201-0055P

9 Drain Cap 1 14965-0025 14965-0025 14965-0025

10 O-Ring, Drain Cap 1 U9-371 U9-371 U9-371

11 Drain Lateral Tube 1 24201-0058 24201-0058 24201-0058

12 O-Ring, Lateral Tube 1 U9-370 U9-370 U9-370

13 Lateral Tube 8 24600-0003 24600-0003 24600-0003

14 Collector Hub Assembly 1 24200-0110 WC137-516P WC137-517P

15 Tank Assembly 1 24200-0100 24201-0100 24203-0100

16 Clamp Knob 1 WC36-22 WC36-22 WC36-22

17 Filter Tank Ass’y (Includes Key Nos. 8 thru 15) 1 24200-9100S 24201-9100S 24203-9100S

18 Washer 1/4" 2 U43-60SS U43-60SS U43-60SS

19 Screw 1/4-20x3/4" Lg. 2 U30-52SS U30-52SS U30-52SS

• Hose, 1-1/2" x 6’ Lg.*** 2 34055-7038 34055-7038 34055-7038

• Sand Shield 1 24201-0043 24201-0043 24201-0043

• Nameplate Decal 1 32155-4115A 32155-4115B 32155-4115C

• Clamp Decal, Warning 1 32165-4030 32165-4030 32165-4030

• Information Decal 1 32155-4112 32155-4112 32155-4112

• Not illustrated. *See Page 15. **See Page 16.

*** Models JSAL15D-59, JSAL180F-05, and JSAL210F-05 do not include 6’ hose.

+ Model JSALS15E uses an “ABG” series pump.

1277 0994

Repair Parts List - Filter

• Not illustrated.

* Not available separately.

Model Motor No. Impeller No.

No. HP (Key No. 6) (Key No. 11)

Single Speed

JWPA5DC-2A3 3/4 AS901DL C105-228PWBS

JWPA5EC-2A3 1 AS901EL C105-228PWS

JWPS5FC-2A3 1-1/2SPL AS901SFL C105-228PWS

Dual Speed

17290-J1002 1 – 1/6 17182-0090 C105-228PWS

Model Cord & Cap Assembly

No. HP (Key No. 2)

JWPA5DC-2A3 3/4 17190-0026-S

JWPA5EC-2A3 1 17190-0026-S

JWPS5FC-2A3 1-1/2SPL 17190-0026-S

Dual Speed

17290-J1002 1 – 1/6 17190-0028-S

Parts are common to all models listed except as noted;

Key Nos. 2, Cord & Cap Assembly; 6, Motor; and 11,

Impeller, are listed below.

Order PKG. 115 for 5" Trap complete (includes

Key Nos. 17 through 25).

13B

13A

NOTICE:

AT23 series models use the

same front plate and

seal plate as other models;

however, they are rotated

90° counter-clockwise

when installed.

782 0294

Key Part

No. Description Qty. Number

1 End Cap Screw 3 37337-0085

2 End Cap and Cord Assembly 1 Chart at Right

3 Toggle Switch 1 16920-0511

4 Toggle Switch Boot 1 32800-0107

5 Baffle Ring 1 17290-0004

6 Motor 1 Chart at Right

7 Motor Cover 1 17190-0021

8 Slinger 1 17351-0009

9 Seal Plate 1 C1-260P

10 Shaft Seal 1 37400-0027S

11 Impeller 1 Chart at Right

12 O-Ring 1 U9-357

13 Front Plate (Includes

Key Nos. 13A, 13B, 19) 1 C101-272PS

13A Wear Ring* 1

13B Pipe Plug 2 WC78-40T

14 Cap Screw 4 30387-0005

15 Trap Lid 1 C3-139P1

16 Trap Lid Gasket 1 U9-229

17 Trap Basket 1 C108-33P

18 Trap Body 1 C153-53P

19 Drain Plug w/O-Ring 2 U178-920P

20 Cap Screw 4 U30-64SS

21 Lock Washer 4 U43-11SS

22 Plain Washer 4 U43-41SS

23 Trap Outlet Gasket 1 C20-123

24 Mounting Foot 1 17190-0023

25 Plain Washer 4 U43-117SS

26 Cap Screw 4 U30-52SS

• Nameplate 1 32155-4073

• Decal – GFCI Required 1 U27-558

• Decal – Insulated Wet End 1 U27-584

• Tag – Do Not Use Pipe Dope 1 61002-0002

• Tag – Caution 1 61002-0004

REPAIR PARTS LIST

POOL PUMPS

3/4 thru 1-1/2 HP Single Speed

1 Hp Dual Speed

13A

81 1293

Model Number

Key No. Description Qty. 3/4 HP 1 HP 1- 1/2 HP

6 Motor 115/60H/1Ph (Without Cord) 1 AS920DLL AS920ELL AS920FLL

6 Motor 230/60H/1Ph (Without Cord) 1 – AS923EL –

6 Motor 115/60H/1Ph 1-Speed (Without Cord) 1 – – 62003-2031

6 Motor 115/60H/1Ph 2-Speed (Without Cord) 1 – 62003-2021 62003-2032

8 Slinger 1 17351-0009 17351-0009 17351-0009

9 Seal Plate 1 17301-0150 17301-0150 17301-0150

10 Shaft Seal 1 37400-0027S 37400-0027S 37400-0027S

11 Impeller 1 C105-228PH C105-228PG C105-228PG

12 O-Ring 1 U9-357 U9-357 U9-357

13 Front Plate (Includes Key Nos. 13A, 13B, 19) 1 C101-272PS C101-272PS C101-272PS

13A Wear Ring* 1

13B Pipe Plug 2 WC78-40T WC78-40T WC78-40T

14 Screw, 1/4-20x1-3/4 6 30787-0005 30787-0005 30787-0005

15 Trap Cover 1 C3-139P1 C3-139P1 C3-139P1

16 Strainer Basket 1 C108-33P C108-33P C108-33P

17 O-Ring - Cover 1 U9-229 U9-229 U9-229

18 Trap Body 1 C153-53P1 C153-53P1 C153-53P1

19 Drain Plug - 1/4" NPT (w/O-Ring) 2 U178-920P U178-920P U178-920P

20 Capscrew 5/16-18x1-1/4" 4 U30-64SS U30-64SS U30-64SS

21 Washer, Lock 5/16" 4 U43-11SS U43-11SS U43-11SS

22 Washer, Flat 5/16" 4 U43-41SS U43-41SS U43-41SS

23 Gasket 1 C20-123 C20-123 C20-123

• Cord Assembly 1 See Chart Above See Chart Above See Chart Above

• Nameplate 1 U33-155 U33-155 U33-155

• Decal “Tested for Pools & Spas” 1 U27-635 U37-635 U27-635

• Decal - GFCI required 1 U27-558 U27-558 U27-558

• Tag - bonding instructions 1 C63-12 C63-12 C63-12

• Tag - CAUTION Securely Tighten…Warning… 1 C63-13 C63-13 C63-13

REPAIR PARTS LIST

JWPA PUMPS

• Not illustrated.

* Not available separately.

-2A2 Models

-2A1 Models 2A, -A2U Models -2A4U Models

HP Cord Ass’y with Cord Ass’y with Cord Ass’y with

Twist-lock Plug Straight Plug Straight Plug

3/4 31953-0101 U117-1117 –

1 31953-0101 U117-1117 –

1-1/2 31953-0101 U117-1118 31953-0116

CORD AND PLUG PART NUMBERS

JWPA5DL-2A1

JWPA5DL-2A2

JWPS5EL-A2

JWPA5EL-2A1

JWPA5EL-2A2

JWPA5E-230A2

JWPA5YFL-A2U

JWPS5FL-A2

JWPA5FL-2A1

JWPA5FL-2A2

JWPAS5F-2A4U

JWPS5FL-A2

ABG PUMPS

• Not illustrated.

* Included with top discharge pumps only.

O N

3345 1198

Key Part Part

No. Description Qty. No.

1 Motor 1 Chart at Right

2 Slinger 1 C69-2

3 Seal Plate 1 17500-0001

4 Seal Plate O-Ring 1 35505-1438

5 Shaft Seal 1 U109-358SS

6 Impeller 1 Chart at Right

7 Floating Wear Ring 1 17500-0004

8 Trap Body 1 17500-0002

9 Trap Lid 1 17500-0003

10 Trap Lid O-Ring 1 35505-1437

11 Trap Basket 1 17350-0100

12 Drain Plug 1 U178-920P

13 Hex Head Bolt,

1/4-20x1-3/4" 4 30787-0005

14 Hex Nut 4 35402-0071

15 Cord 1 Chart at Right

• Hardware Kit*

(2 Bolts, 2 Washers) 1 17290-0001

• Nameplate 1 U33-155

• Warning Tag 1 61002-0013

• Caution Tag 1 C63-12

• Decal - “GFCI Required” 1 U27-558

Parts are common to all models listed except as noted:

Key Nos. 1, Motor; 6, Impeller; and 15 Cord are listed below.

For complete suction trap order Pkg. 115.

Motor No. Impeller No. Cord No.

Model No. HP Key No. 1 Key No. 6 Key No. 15

115 Volt/1-Speed, Top Discharge

ABG4C-3A4 1/2 62003-2034 17301-0114 31953-0116

ABG4C7-3A4 1/2 62003-2034 17301-0114 31953-0116

ABG4DL-2A1 3/4 AS920DLL 17301-0113 31953-0101

ABG4D-2A4 3/4 AS920DLL 17301-0113 31953-0116

ABGS4D-3A4 3/4 62003-2035 17301-0114 31953-0116

ABGS4DL-A2 3/4 62003-2035 17301-0114 U117-1117

ABGS4EL-A2 1 AS920DLL 17301-0113 U117-1117

ABG4EL-2A1 1 AS920ELL 17301-0112 31953-0101

ABG4EL-2A2 1 AS920ELL 17301-0112 U117-1117

ABG4E-2A4 1 AS920ELL 17301-0112 31953-0116

ABG4E-2A4SP 1 AS920ELL 17301-0112 31953-0116

ABGS4E-3A4 1 62003-2037 17301-0113 31953-0116

ABG4FL-2A1 1-1/2 AS920FLL 17301-0111 31953-0101

ABGS4FL-A2 1-1/2 62003-2031 17301-0112 U117-1117

ABGS4F-2A4 1-1/2 62003-2031 17301-0112 31953-0116

115 Volt/1-Speed, Side Discharge

ABG4D7L-2A1 3/4 AS920DLL 17301-0113 31953-0101

ABG4D7-2A4 3/4 AS920DLL 17301-0113 31953-0116

ABGS4D7-3A4 3/4 62003-2035 17301-0114 31953-0116

ABG4E7L-2A1 1 AS920ELL 17301-0112 31953-0101

ABG4E7L-2A2 1 AS920ELL 17301-0112 U117-1117

ABG4E7-2A4 1 AS920ELL 17301-0112 31953-0116

ABG4E7-2A4SP 1 AS920ELL 17301-0116 31953-0116

ABG4E7-2A4SPH 1 AS920ELL 17301-0113 31953-0116

ABGS4E7-3A4 1 62003-2037 17301-0113 31953-0116

ABG4F7L-2A1 1-1/2 AS920FLL 17301-0011 31953-0101

ABGS4F7-2A4 1-1/2 62003-2031 17301-0112 31953-0116

115 Volt/2-Speed, Top Discharge

ABG4YD-A1 3/4 AS900DLL-Y 17301-0113 31953-0101

ABG4YD-A2 3/4 AS900DLL-Y 17301-0113 U117-1117

ABG4YE-2A4 1 62003-2021 17301-0112 31953-0116

ABG4YF-A2 1-1/2 62003-2032 17301-0111 U117-1117

ABGS4YG-A1 2 62003-2023 17301-0111 31953-0101

ABGS4YG-A2 2 62003-2023 17301-0111 U117-1117

115 Volt/2-Speed, Side Discharge

ABG4YE7-2A4 1 62003-2021 17301-0112 31953-0116

ABGS4YE7-A1 1 AS900DLL-Y 17301-0113 31953-0101

ABGS4YE7-A2 1 AS900DLL-Y 17301-0113 U117-1117

ABG4YF7-A2 1-1/2 62003-2032 17301-0111 U117-1117

ABGS4YF7-A1 1-1/2 62001-1035 17301-0112 31953-0101

ABGS4YF7-A2 1-1/2 62001-1035 17301-0112 U117-1117

Aquatools

.WATERFORD, WI.

53185

USA

762 0294

Key Part

No. Description Qty. Number

Decal, Valve Handle 1 32145-4016

2 Handle 1 14962-0032

3 Dowel Pin 1 35857-0021

4 Washer 1 14965-0007

5 Decal, Operating Instructions 1 14965-0020

6 Screw 7 37067-0714

7 Valve Cover 1 14965-0011

8 O-Ring 1 35505-1228

9A Washer 2 14965-0007

9B Washer 1 14965-0007

10 Spring 1 14965-0006

11 Pressure Gage 1 15060-0000T

12 O-Ring, Cover 1 35505-1275

13 Plug & Gasket Assembly 1 14965-0028

14 Valve Body Assembly 1 14965-0013

15 Nut 7 35407-0071

16 O-Ring, Tank Flange 1 U9-369

REPAIR PARTS LIST

WC112-148A MULTIPORT VALVE

CREATE A RECORD OF YOUR WARRANTY AT STA-RITE:

• Complete a warranty registration at www.staritepool.com by clicking on “Register Products” and selecting Sta-Rite Pool

• Complete bottom portion completely and mail within 10 days of installation to Sta-Rite, Attn.: Pool Warranty Dept., 293 Wright St., Delavan , WI 53115

Warranty Registration Card

Name

Address

City State Zip

Installation (or Purchase) Date

Product Purchased

Model Number

■■ New installation ■■ Replacement

Years pool has been in service ■■ less than 1 ■■ 1-3 ■■ 3-5 ■■ 5-10

This product was purchased from:

Company name

Address

City State Zip

STA-RITE LIMITED WARRANTY

For technical information about this product, contact the installer or call Sta-Rite at 262-728-9181.

Visit www.staritepool.com

• for more information about Sta-Rite products listed above

• to locate a Sta-Rite dealer near you

Product Specific Warranties

(from date of installation)

Product Limited

Family Warranty Exceptions

Filters 1 Year System 3 Tank Bodies - 10 Yrs

Filter Valves 1 Year

Pumps 1 Year

Heaters 2 Years *Commercial Application - 1 Yr

Controls 1 Year

Above Ground Systems 1 Year

Lights and Niches 1 Year Lamps and Bulbs - 90 Days

White Goods 1 Year

Maintenance Equipment 90 Days

Drainer/Utility Pumps 90 Days

Replacement Parts 90 Days

Cleaners: Lil Shark 1 Year

Cleaners: Calypso 1 Year

Cleaners: Pool Shark 2 Years Footpad and Seal Flaps - 1 Yr

Cleaners: Great White 2 Years

* Commercial and multi-family application.

Retain this warranty certificate in a

safe and convenient location for your records.

Pumps, filters, skimmers, underwater lights (excluding bulbs), ac-

essories and fittings manufactured by Sta-Rite are warranted to

be free of defects in material and/or workmanship for one (1) year

from the original date of installation.

The foregoing warranties relate to the original consumer purchaser

(“Purchaser”) only. Sta-Rite Industries shall have the option to re-

pair or replace the defective product, at its sole discretion.

Purchasers must pay all labor and shipping charges necessary to

replace the product covered by this warranty. Requests for war-

ranty service must be made through the installing dealer. This war-

ranty shall not apply to any product that has been subject to

negligence, misapplication, improper installation or maintenance,

or other circumstances which are not in Sta-Rite’s direct control.

ailure to have product installed by a professional in compliance

with local codes will void any and all manufacturers warranty.

This warranty sets forth Sta-Rite’s obligation and Purchaser’s ex-

clusive remedy for defective products.

STA-RITE SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL,

INCIDENTAL OR CONTINGENT DAMAGES WHATSOEVER.

THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN

LIEU OF ALL OTHER EXPRESS WARRANTIES. IMPLIED WAR-

RANTIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE, SHALL NOT EXTEND BEYOND THE

DURATION OF THE APPLICABLE EXPRESS WARRANTIES

PROVIDED HEREIN.

Some states do not allow the exclusion or limitation of incidental or

consequential damages or limitations on how long an implied war-

ranty lasts, so the above limitations or exclusion may not apply to

you. This warranty gives you specific legal rights and you may also

have other rights which vary from state to state.

Supersedes all previous publications.

S4877PS (Rev. 7/21/04)

La page charge ...

Waterford JSAL15D Le manuel du propriétaire

Marque: Waterford

Modèle: JSAL15D

Catégorie: Accessoires de piscine hors terre

Taper: Le manuel du propriétaire

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Waterford JSAL15D Owner's manual

Waterford JSAL15D Le manuel du propriétaire

Ce manuel convient également à

Waterford JSAL15D Le manuel du propriétaire

dans d''autres langues

Autres documents