CombiSteel 7178.0290 Manuel utilisateur

User and Maintenance

Instructions

Fryer

(Electric)

Handleiding Voor

Bediening En Onderhoud

Frituur

(Elektrisch)

Betriebs- und

Wartungsanleitung

Friteuse

(Elektrisch)

Manuel d’Utilisation et de

Maintenance

Friteuse

(Électrique)

2

Table of Contents / Inhoudsopgave /

Inhaltsverzeichnis / Table des Matières

I. ENGLISH ………………………………………………………………. 3

A. Description

B. Products

C. Mounting Instructions

D. Operator Instructions and Attention Points

E. Figures

F. Product Drawings

G. Electrical Connection Drawing

II. NEDERLANS ………………………………………………………… 24

A. Beschrijving

B. Producten

C. Montage-Instructies

D. Instructies van de bediener en aandachtspunten

E. Figuur

F. Producttekeningen

G. Elektrische Aansluittekeningen

III. DEUTSCH …………………………………………………………….. 45

A. Beschreibung

B. Produkte

C. Installationsanleitung

D. Benutzerhinweise und zu Beachtende Punkte

E. Abbildung

F. Produktzeichnungen

G. Elektrische Anschlusszeichnung

IV. FRANÇAIS …………………………………………………………… 66

A. Explications

B. Des Produits

C. Instructions de Montage

D. Instructions a L’utilisateur et Points a Considérer

E. Les Figures

F. Dessins des Produits

G. Dessin de connexion électrique

3

User and Maintenance

Instructions

Fryer (Electric)

4

A. DESCRIPTION

Our dear customer,

Your preferred COMBISTEEL is nature and technology friendly. We thank you for your choice.

COMBISTEEL has been produced with the understanding of "Total Quality" in modern

production facilities.

Important Safety Information

Carefully read this guide and keep it for future review.

WARNING: Installation of the devices must be done by an authorized service person.

WARNING: Equipment must be grounded.

Indicates that there is a risk of personal injury or property damage.

Explosion / fire hazard

 Mounting, electrical connection and maintenance works of the device should be

performed by a specialist authorized in this subject and in accordance with the instructions

of the manufacturer company.

 Electrical connection of the device should be arranged according to the tables and

electrical diagram given in this manual.

 Manufacturer Company accepts no responsibility for the final damages that are caused by

any procedure not conforming to the instruction manual, or maintenance or technical

interventions that are not performed by authorized people.

5

B. PRODUCTS

C. MOUNTING INSTRUCTION

Placement

 Installation and adjustment of the device should be carried out by experienced technical

staff.

 In order to prevent smell and fume formation, place the device beneath an exhaust hood

being capable of enough ventilation.

 Place the device at a place min. 10cm away from the side or back wall to prevent excessive

temperature rises.

 Device should be placed on a flat surface by suitably balancing on the four adjustable

legs. (Figure A)

 Remove the nylon protection cover on the device. If there are any adhesive residues left

on the surface, clean with a suitable solvent.

 Never leave flammable material near the device.

CODE

DESCRIPTION

SERIE

7178.0088

Electric fryer, tabletop model, 10 litres

600

7178.0090

Electric fryer, tabletop model, 10 litres

600

7178.0095

Electric fryer, tabletop model, 2x10 litres

600

7178.0520

Electric fryer on closed cabinet, 18 litres

700

7178.0522

Electric fryer on closed cabinet, 10 litres

700

7178.0525

Electric fryer on closed cabinet, 2x18 litres

700

7178.0527

Electric fryer on closed cabinet, 2x10 litres

700

7178.0285

Electric fryer, tabletop model, 10 litres

700-S

7178.0290

Electric fryer, tabletop model, 2x10 litres

700-S

7178.3055

Electric fryer on closed cabinet, 22 litres

900

7178.3060

Electric fryer on closed cabinet, 2x22 litres

900

6

Electrical Connection

 Connect the device to the electrical installation according to the electrical standards of

the relevant country.

 Feed the device with suitable network voltage written on the information plate.

 Connect to the electrical installation over a suitable automatic fuse. Fix the said fuse on a

place that is easily accessible in case of a danger.

 The cable connecting the device to the electrical installation should be at least type H05

RNF.

 Before connecting the electrical inlet cable to the electrical inlet clamp, connect the cable

on the device by passing it through the inlet coupling and then tighten the coupling cover

in a manner that does not allow cable return.

 Voltage tolerance should not exceed ± 10%.

 Electrical inlet clamp can be seen by disassembling front panel.

 Electrical inlet is indicated with a label on the device.

 If the device will be used in a commercial kitchen, apply a correct grounding system.

Here, consider DIN VDE D100 Article 540.

 The device must be grounded. Grounding point is marked with " ".

D. OPERATOR INSTRUCTIONS AND ATTENTION POINTS

WARNINGS

 Pay attention not to contact hot surfaces of the device!

 Device is designed for professional use and must be used only by person who are trained

for this intention.

 Device is intended for cooking, do not use for another purpose.

 If there is any failure in the device, disconnect electrical power by deactivating the main

switch.

 Commission only authorized services for maintenance and use genuine spare parts.

 Before starting to use the device, carefully clean the surfaces especially those to be in

contact with foods.

 During first operation, device will emit fume and smell for a short period. This fume and

smell is the result of the insulation material and the substances such as oil, etc. on the

metal sheet surfaces. This is not dangerous and will disappear by itself.

 Do not operate the device without oil or under minimum level (Figure B)

 Before filling oil, close discharge valve.

 Fill oil up to the maximum level prior to put into operation.

 Replace frying oil with certain intervals before its properties are lost. Thus, you prevent

also burned and carbonized residue accumulation on heater and chamber surface.

 Refill oil when it descends to minimum level. Minimum and maximum oil levels are

marked on oil container. (Figure B)

 Do not place foods without draining their water, or foods with solid ice parts.

 Rise up the movable headed heater group (4) through its lever to allow cleaning.

Afterwards, you should side-shift support latch (5) to take down it again. (Figure C)

 Do not use fat. Do not use without oil. Do not open valve when oil is not.

7

MAINTENANCE

 Do not perform maintenance when the device is hot and loaded with electrical power.

 Before it cools down completely, wipe the device with a cloth immersed in warm soapy

water.

 Firstly fill in water and boil to clean oil chamber. This will help cleaning the concrete and

sticky oils easily. Discharge assembly will also be cleaned.

 Do not use cleaning substances and tools that may cause scratches on device surface.

 If required, use chemical cleaners.

 Do not clean the device with water or vapour pressure. Otherwise, you may cause

electrical installation failure.

 If the device will not be used for a long period, coat the surfaces with a thin layer of

Vaseline.

 In case of any dangerous condition with the device, notify to the authorized service. Never

let unauthorized people to interfere in the device.

START-UP (Figure D)

 Turn switch a "6" to position "1".

 Adjust thermostat "7" to desired temperature.

 When signal light "8" is off, the oil reaches to desired temperature. You can now start to

cook.

TURNING OFF (Figure D)

 Turn thermostat "6" to position "0".

 Turn switch a "7" to position "0".

IMPORTANT

Thermostat is limited with 230º C; if it reaches to this temperature for any reason, the circuit

will be cut off. In order to reactivate, wait for oil to cool. Then, by opening the cabinet cover,

push down the red button seen on the installation metal sheet present on the lower part of the

front panel with a thin screwdriver until a contact sound is emitted. If this limit switch activates

the circuit again after the oil is heated, apply to the authorized service.

8

Compatibility Information

This device is designed and manufactured in accordance with the following directives and

standards

marking directive, 93/68/EEC

TS EN 60335-1:2012/AC

TS EN 60335-2-37:2002

Related to CE Directive(s):

2014/35/EU (Low Voltage)

 Limitation of Liability: All technical information contained in this manual, operating

instructions, operation and maintenance of the device, contains the latest information on your

device. The manufacturer accepts no responsibility for damage or injury which may result

from failure to follow the instructions in this manual, use outside of the intended use,

unauthorized repair, unauthorized modifications to the device, or use of spare parts not

approved by the manufacturer.

9

E. FIGURES

Figure A

Figure B

10

Figure C

Figure D

11

F. PRODUCT DRAWINGS

Product

Width

(W)

Depth

(D)

Height

(H)

Electrical

Inlet

Power

Cable

Sections

Weight

Volume

Capacity

7178.0088

300 mm

600 mm

300 mm

230V AC

1N PE

3,5 kW

3x2.5

H05RNF

17 kg

0.14

m³

10 lt

7178.0090

400 mm

600 mm

300 mm

400V AC

3N PE

7,5 kW

5x2.5

H05RNF

20 kg

0.18

m³

10 lt

7178.0095

600 mm

300 mm

400V AC

3N PE

15 kW

5x4

H05RNF

34 kg

0.28

m³

2x10 lt

7178.0520

400 mm

700 mm

900 mm

400V AC

3N PE

14 kW

5x4

H05RNF

53 kg

0.44

m³

18 lt

7178.0522

400 mm

700 mm

900 mm

400V AC

3N PE

7,5 kW

5x2.5

H05RNF

53 kg

0.44

m³

10 lt

7178.0525

800 mm

700 mm

900 mm

400V AC

3N PE

28 kW

5x6

H05RNF

83 kg

0.90

m³

2x18 lt

7178.0527

800 mm

700 mm

900 mm

400V AC

3N PE

15 kW

5x4

H05RNF

81 kg

0.84

m³

2x10 lt

7178.0285

400 mm

700 mm

300 mm

400V AC

3N PE

7,5 kW

5x2.5

H05RNF

28 kg

0.21

m³

10 lt

7178.0290

800 mm

700 mm

300 mm

400V AC

3N PE

15 kW

5x4

H05RNF

47 kg

0.36

m³

2x10 lt

7178.3055

400 mm

900 mm

400V AC

3N PE

18 kW

5x4

H05RNF

64 kg

0.56

m³

22 lt

7178.3060

800 mm

900 mm

400V AC

3N PE

36 kW

5x6

H05RNF

94 kg

1.05

m³

2x22 lt

12

7178.0088

7178.0090

13

7178.0095

7178.0520

14

7178.0522

7178.0525

15

7178.0527

7178.0285

16

7178.0290

7178.3055

17

7178.3060

18

G.ELECTRICAL CONNECTION DRAWING

7178.0088

19

7178.0090 / 7178.0520 / 7178.0522 / 7178.0285

20

7178.0095 / 7178.0525 / 7178.0527 / 7178.0290

La page est en cours de chargement...

CombiSteel 7178.0290 Manuel utilisateur

Ce manuel convient également à

CombiSteel 7178.0290 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents