Maximum 10-Gallon Quiet Cabinet Le manuel du propriétaire

Marque: Maximum

Modèle: 10-Gallon Quiet Cabinet

Catégorie: Compresseurs d'air

Taper: Le manuel du propriétaire

10 38

ULTRA-QUIET

Air Compressor

058-1980-4

TABLE OF CONTENTS

TECHNICAL SPECIFICATIONS 4

SAFETY GUIDELINES 5

KEY PARTS DIAGRAM 8

KEY PARTS LIST 9

INTENDED USE 10

ASSEMBLY 12

OPERATING INSTRUCTIONS 14

MAINTENANCE 18

TROUBLESHOOTING 20

EXPLODED VIEW 22

SAVE THESE INSTRUCTIONS

Keep this instruction manual for future use. Should this product be passed on to a third party,

this instruction manual must be included.

PARTS LIST 23

WARRANTY 24

NOTE:

If any parts are missing or damaged, or if you have any questions, please call our toll-free helpline

at 1-888-670-6682.

4 5

TECHNICAL SPECIFICATIONS

SAFETY GUIDELINES

This manual contains information that relates to PROTECTING PERSONAL SAFETY

and PREVENTING EQUIPMENT PROBLEMS.

carefully and understand it thoroughly before using the product. The symbols listed

below are used to indicate this information.

IMPORTANT!

Installation, operation or maintenance information that is important but not hazard related.

It is very important to read this manual

CAUTION!

Potential hazard that may result in moderate injury or damage to equipment.

WARNING!

Potential hazard that could result in serious injury or loss of life.

DANGER!

Potential hazard that will result in serious injury or loss of life.

Safety Advice

1. RISK OF FIRE OR EXPLOSION.

2. RISK OF ELECTRIC SHOCK.Do not expose to rain. Store indoors. Hazardous voltage.

Disconnect from power source before servicing. Compressor must be grounded. Do not

use grounding adaptors.

3. RISK OF PERSONAL INJURY. Never spray compressed air or material at self or others.

4. RISK OF BURSTING. Check the maximum pressure rating in the manual or identiﬁcation

5. Do not adjust the pressure switch or safety valve for any reason. They

RISK OF BURSTING.

Do not spray a ﬂammable or combustible liquid or paint

label. The compressor outlet pressure must be regulated so that it does not exceed the

maximum pressure rating. Relieve all pressure in the hose before removing or attaching

accessories. Make sure the regulator is adjusted so that the compressor outlet pressure is

set lower than the maximum operating pressure of the spray gun or tool. Before starting the

compressor, pull the ring on the safety valve to make sure the valve moves freely (see diagram

on page 19). Drain water from tank after each use. Do not weld or repair tank.

have been preset at the factory for this compressor’s maximum pressure. Tampering

with the pressure switch or the safety valve may cause personal injury or property damage.

near sparks, ﬂames, pilot lights or in a conﬁned area. The spray area must be well-ventilated.

Keep compressor at least 20' (6 m) away from spray area. Do not carry and operate the

compressor or any other electrical device near the spray area. Never smoke when spraying.

Use a minimum of 25' (7.6 m) of hose to connect a spray gun to the compressor.

model no. 058-1980-4 | contact us 1-888-670-6682

TECHNICAL SPECIFICATIONS

*CFM: Cubic Feet per Minute

1.3

4.0

120

150

10 U.S. GALLONS (38 L)

OIL-LESS

NI DUCTION

3.0

RUNNING HP

TANK SIZE

AIR DELIVERY (CFM*) @ 40 PSI

AIR DELIVERY (CFM*) @ 90 PSI

CUT-IN PRESSURE (PSI)

CUT-OUT PRESSURE (PSI)

PUMP DESIGN

MOTOR

120 V, 60 Hz, 8.5 A

132 lb 4 1/2 oz (60 kg)

SJOW 16 AWG/72" (1.83 m)

POWER

WEIG

56 dB(A)

SOUND LEVEL

POWER CORD

6 7

SAFETY GUIDELINES

SPECIFIC SAFETY GUIDELINES FOR THE SLIDING WET TILE SAW

SAFETY GUIDELINES

WARNING!

Pull the pressure safety valve ring every day in order to ensure that the valve is functioning properly.

The compressor must be located in a well-ventilated area for cooling, and it must be a minimum of 12"

(31 cm) away from the nearest wall.

Protect the air hose and the power cord from damage and puncture. Inspect them for weak or worn spots

every week, and replace them if necessary.

Always wear hearing protection when using an air compressor. Failure to do so may result in hearing loss.

Do not carry the compressor while it is running.

Do not operate the compressor if it is not in a stable position.

Do not operate the compressor on a rooftop or an elevated position that could allow the unit to fall or be

tipped over.

Always replace a damaged gauge before operating the unit again.

WARNING!

CORD SIZE IN AWG (AMERICAN WIRE GAUGE)

Extension cord length

25' (7.6 m) 50' (15 m) 75' (23 m) 100' (30 m) 150' (46 m) 200' (60 m)

0 – 5 16 16 16 14 12 12

5.1 – 8 16 16 14 12 10 —

8.1 – 12 14 14 12 10 — —

12.1 – 15 12 12 10 10 — —

15.1 – 20 10 10 10 — — —

AMPERE

RATING

6. RISK OF BURNS. The pump and the manifold generate high temperatures. In order to

avoid burns or other injuries, do not touch the pump, the manifold or the transfer tube

while the compressor is running.

Allow the parts to cool down before handling or

servicing. Keep children away from the compressor at all the times.

Be certain to read all labels when you are spraying paints or

toxic materials, and follow all safety instructions. Use a respirator mask if there is a

chance of inhaling anything you are spraying. Also, NEVER directly inhale the air

BREATHING RISK.

Extension cords

As the distance from the supply outlet increases, you must use a heavier gauge extension cord. Using

extension cords with inadequately sized wire causes a serious drop in voltage, resulting in loss of power

and possible product damage. Refer to the table here to determine the required minimum wire size.

Recommended Minimum Wire Gauge for Extension Cords* (120 V)

* Based on limiting the line voltage drop to ﬁve volts at 150% of the rated amperes.

The smaller the gauge number of the wire, the greater the capacity of the cord. For example, a 14-gauge

cord can carry a higher current than a 16-gauge cord. When using more than one extension cord to make

up the total length, be sure each cord contains at least the minimum wire size required.

Guidelines for using extension cords

•

If you are using an extension cord outdoors, be sure it is marked with the sufﬁx "W-A"("W" in

Canada) to indicate it is acceptable for outdoor use.

Ensure your extension cord is properly wired and in good electrical condition. Always replace a

damaged extension cord or have it repaired by a qualiﬁed technician before using it.

Protect your extension cords from sharp objects, excess heat, and damp or wet areas.

produced by a compressor.

8. Wear ANSI Z87.1 or CSA Z94.3 approved safety goggles when using

RISK OF EYE INJURY.

an air compressor. Do not point any nozzle or sprayer toward a person or any part of the

body. Serious injury may occur if the spray penetrates the skin.

9. RISK TO HEARING. Always wear hearing protection when using an air compressor.

Failure to do so may result in hearing loss.

model no. 058-1980-4 | contact us 1-888-670-6682

8 9

KEY PARTS DIAGRAM

KEY PARTS LIST

WARNING!

Do not exceed the tool’s maximum working pressure.

WARNING!

Do not attempt to open the drain valve when there is more than 10 PSI of air pressure in the tank.

Plug

Grounding pin

Grounded

outlets

B. AIR COMPRESSOR PUMP: The pump compresses the air and discharges it into the tank via the piston

that moves up and down in the cylinder.

C. ON/OFF SWITCH: This switch turns the compressor on and off. It is operated manually, and when it is

in the ON position it allows the motor to start if the pressure in the air tank is below the factory set cut-in

pressure, and it allows the motor to stop if the pressure in the air tank reaches the factory set cut-off

pressure. Be sure to set this switch to the OFF position when the compressor is not being used and before

unplugging the compressor.

D. SAFETY VALVE: This valve is used to prevent system failure by draining pressure from the system when

it reaches a preset level if the pressure switch has not shut down the motor. It will pop open automatically,

or it can be activated manually by pulling the ring on the valve.

E. AIR PRESSURE REGULATOR: The regulator is used to adjust the pressure inside the line to the tool that

is being used. Turn the knob clockwise to increase the pressure and counter-clockwise to decrease the

pressure.

F. TANK PRESSURE GAUGE: The gauge measures the pressure level of the air that is stored in the tank.

It cannot be adjusted by the operator and it does not indicate the pressure inside the line.

G. OUTLET PRESSURE GAUGE: The gauge measures the regulated outlet pressure.

H. AIR OUTLET: The outlet is connected to the 1/4” (6.4 mm) NPT air hose.

I. AIR TANK DRAIN VALVE: The drain valve is used to remove moisture from the air tank after the

compressor is shut off.

J. AIR TANK: The tank is where the compressed air is stored.

K. POWER CORD: This compressor should be

L. DRAIN PIPE: The drain pipe is connected to the drain valve directly during shipment, and is to be used for

draining air and pollution easily.

used on a nominal 120 V grounded circuit. Use a power cord

that is equipped with a grounding plug. Verify that the compressor is plugged into an outlet that has the same

conﬁguration as the plug. Do not use an adaptor with this compressor.

A. ELECTRIC MOTOR: The motor is used to power the pump. It is equipped with a thermal overload protector.

If the motor overheats for any reason, the thermal overload protector will shut it down in order to prevent

the motor from being damaged.

ELECTRIC MOTOR (A)

SAFETY VALVE (D)

ON/OFF SWITCH (C) AIR OUTLET (H)

TANK PRESSURE GAUGE (F)

POWER CORD (K)

AIR COMPRESSOR

PUMP (B)

AIR PRESSURE

REGULATOR (E)

OUTLET PRESSURE GAUGE (G)

AIR TANK

DRAIN VALVE (I)

AIR TANK (J)

DRAIN PIPE (L)

model no. 058-1980-4 | contact us 1-888-670-6682

10 11

INTENDED USE

•

WARNING!

This air compressor is not designed for continuous operation or unlimited commercial operations

and may be used in dry areas only. This air compressor is intended to be used in maximum

30-minute intervals and should rest for 30 minutes before being used again. Do not exceed the

maximum working time.

Before you start

This MAXIMUM Ultra-Quiet Air Compressor is ideal for a wide range of applications from fastening to

greasing and engine cleaning. The 10 gallon (38 L) design provides optimum pressure. It features an

oil-free pump and uses a 1.3 HP induction motor for powerful operation.

The procedures described in this manual are solely for this 10 gallon (38 L) air compressor at a maximum

pressure of 150 PSI. The device has been designed/constructed for household use only.

Compatible compressor and air tool: proper usage and operation

Always ensure the use of appropriately-matched air tools with your MAXIMUM Ultra-Quiet Air Compressor.

Be sure that the air compressor being used can supply the appropriate volume, pressure and delivery rate

of air to the tool(s) without running continuously. Using tools, or combinations of tools together or

separately, that require more than the air compressor can deliver will void the air compressor

guarantee/warranty.

model no. 058-1980-4 | contact us 1-888-670-6682

Air Tool

Tool Compatibility Chart

Operates Tool

Continously Not

Recommended

Operates Tool

Intermittently

Inﬂation/Recreation

Finishing Nailer (16-gauge)

Framing Nailer

Flooring Nailer

Die Grinder/Angle

Grinder/Air Ratchet

Cut-Off Tool

Paint Sprayer

Brad Nailer (18-gauge)

3-in-1 Brad/Finishing/Stapler

Rooﬁng Nailer

Impact Wrench

Drill/Hammer/Chisel/Shears

Sander/Polisher

Grease/Caulking Gun

12 13

ASSEMBLY

Assembly

1. Unpack the air compressor. Inspect the unit for damage. If the unit has been damaged, contact the

retailer immediately.

THE CARTON SHOULD CONTAIN:

•Air compressor.

•Owner’s manual.

2. Check the air compressor’s identiﬁcation label to ensure that you have purchased the intended model

and that it has the required pressure rating for its intended use.

3. Positioning of the air compressor:

a. Position the air compressor near an electrical outlet.

b. The compressor must be at least 12" (31 cm) from any wall or obstruction, in a clean, well-ventilated

area to ensure sufﬁcient airflow and cooling.

c. Place the air compressor on the ﬂoor or a hard, level surface. The air compressor must be level to

d. After the machine is placed in the working position, please put the front wheel brake down to prevent

the machine from moving during the work.

ensure proper drainage of the moisture in the tank.

4. Connect air hose to compressor.

•Connect air hose (not provided) to the compressor’s air outlet (H).

NOTE: To avoid personal injury, DO NOT grab only the sliding handle to lift the whole unit.

> 12" /

31 cm

Wall

ASSEMBLY

model no. 058-1980-4 | contact us 1-888-670-6682

14 15

OPERA

OPERATING INSTRUCTIONS

Breaking-in the pump

1. Set the ON/OFF switch (C) to the OFF position.

2. Take out the drain pipe wrapped around the bottom of the product,

place the sewage outlet of the drain pipe (L) in a suitable location

(sewer, etc.), and open the tank drain valve (I) by turning it counter-clockwise

to permit the air to escape and prevent air pressure build-up in the

air tank during the break-in period.

3. Turn the air pressure regulator (E) clockwise until it stops.

4. Plug in the power cord (K).

NOTE: A circuit breaker is recommended. If the air compressor is connected to a circuit protected by a

dual-element time delay fuses (type“T” only).

5. Set the ON/OFF switch (C) to the ON position. The compressor will start. Run the compressor for 30

minutes. If it fails, turn it off immediately and call the toll-free helpline at 1-888-670-6682. Please note

that breaking-in the unit is only required prior to ﬁrst use.

7. When the compressor has finished draining, close the drain valve by turning it clockwise the

drain pipe (L). There are two ways to store the drain pipe (L):

a. Rewind the drain pipe (L) to the bottom hook of the product.

b. The head of the sewage pipe has a magnet that can be attached to the proper position of

the product.

After 30 minutes, turn off the ON/OFF switch (C).

8. Set the ON/OFF switch (C) to the ON position. The air tank will ﬁll to “cut-out” pressure and then

the compressor’s motor will stop. The compressor is now ready for use.

CAUTION!

Use a dedicated circuit.

For best performance and reliable starting, the air compressor should be plugged into a dedicated circuit,

as close as possible to the fuse box or circuit breaker.

The compressor will use the full capacity of a typical 15 A household circuit. If any other electrical

from the compressor’s circuit, the air compressor may fail to start. Low voltage

sluggish starting that causes the motor overload protection

devices are drawing

or an overloaded circuit can result in

system or circuit breaker to trip, especially in cold conditions.

fuse, use

OPERATING INSTRUCTIONS

OFF

OPEN

model no. 058-1980-4 | contact us 1-888-670-6682

16 17

OPERATING INSTRUCTIONS

WARNING!

Risk of bursting. Too much air pressure causes a hazardous risk of bursting. Check the manufacturer’s

maximum pressure rating for air tools and accessories. The regulator outlet pressure must never exceed

the maximum pressure rating.

If the pump has been transported or turned upside down (even partially), allow the pump to sit in a normal,

upright position for approximately 10 minutes before starting.

High temperatures are generated by the electric motor and the pump. To prevent burns or other injuries,

DO NOT touch the air compressor while it is running. Allow it to cool before handling or servicing. Keep

children away from the air compressor at all times.

WARNING!

CAUTION!

Escaping air and moisture can propel debris that may cause eye injury. Wear safety goggles when opening the

drain valve.

WARNING!

To avoid personal injury, always shut off and unplug the unit, and relieve all air pressure from the system before

performing any service on the air compressor.

Risk of unsafe operation. Unit cycles automatically when power is on. When performing maintenance you may be

exposed to voltage sources or compressed air. Disconnect power source from the compressor and bleed off all

air pressure.

WARNING!

Before each start-up

1. Set the ON/OFF switch (C) to the OFF position.

2. Turn the air pressure regulator knob (E) counter-clockwise until it stops.

3. Attach hose and accessories.

How to start

1. Close the tank drain valve (I).

2. Plug in the power cord (K).

3. Set the ON/OFF switch (C) to the ON position and allow tank pressure to build. Motor will

stop when tank pressure reaches “cut-out” pressure.

4. Turn the air pressure regulator knob (E) clockwise until desired pressure is reached.

5. The compressor is ready for use.

How to shut down

1. Set the ON/OFF switch (C) to the OFF position.

2. Unplug the power cord (K).

3. Reduce the pressure in the tank through the outlet hose. Pulling the drain valve (I), and keeping it open,

will also reduce the pressure in the tank.

DRAIN PIPE

OPEN

model no. 058-1980-4 | contact us 1-888-670-6682

18 19

MAINTENANCE

Unplug the power cord (K).

MAINTENANCE

Check that all connections are tight. Small leaks in the tank,

hoses, connections or transfer tubes will substantially reduce the

air compressor and tool performance. Spray a small amount of

soapy water around the area of suspected leaks with a spray

bottle. If bubbles appear, repair, replace or reseal the faulty

component. Do not over-tighten any connections.

To check safety valve

To drain tank

1. Set the ON/OFF switch (C) to the OFF position.

3. Turn air pressure regulator (E) counter-clockwise to set the outlet pressure to zero.

4. Pull and hold ring on safety valve (D), allowing air to bleed from the tank until air pressure is

minimized.

5. Place suitable container under unit to catch water.

Slightly tilt unit and turn drain valve (I) counter-clockwise to open.

7. After the water has been drained, close the drain valve (I) (clockwise). The air compressor can now

be stored.

If any of the following symptoms appear while operating the product, stop using the product immediately

or serious personal injury could result. Only an authorized service centre should perform repairs on this

product.

WARNING!

NOTE:

If any of the following symptoms appear while operating the product, stop using the product immediately

or serious personal injury could result. Only an authorized service centre should perform repairs on this

product.

WARNING!

Risk of bursting. Water will condense in the air tank. If not drained water will corrode and weaken the air

tank causing a risk of air tank rupture.

WARNING!

Risk of bursting. If the safety valve does not work properly, over-pressurization may occur causing air tank

rupture or an explosion.

NOTE: Allow unit to cool before draining tank. Drain valve (I) becomes hot during operation.

NOTE: Troubleshooting problems may have similar causes and solutions.

Disconnect the electrical plug and disconnect any tools from air supply before attempting any adjustment.

NOTE:

model no. 058-1980-4 | contact us 1-888-670-6682

ITEM DESCRIPTION/REASON SERVICE

INTERVAL

Drain

the tank

Check the

valve

Pull/activate the safety valve daily to ensure that it is operating

properly and to clear the valve of any possible obstructions.

Daily

Test for

leaks Monthly

Storage Prior to

storing

Daily

Clean the

air ﬁlter Weekly

Through normal operation of your air compressor, condensation

water will accumulate in the tank. To prevent corrosion of the

tank from the inside, condensation must be drained at the end of

every work day. Be sure to wear protective goggles. Relieve the

air pressure in the system, then open the drain valve on the

bottom of the tank to drain. In cold conditions it is especially

important to drain the tank after each use to reduce the chance

of problems resulting from the freezing of condensation water.

NOTE: Refer to instructions on how to drain tank (page 19).

A dirty air ﬁlter will reduce air compressor performance and life.

To avoid contaminating the pump, the ﬁlter should be cleaned

frequently and replaced on a regular basis. Clean the foam ﬁlter

by immersing it in warm, soapy water. Dry thoroughly after.

Before storing the air compressor, do the following:

• Drain tank (page 19).

• Use an air blow gun to clean all dust and debris from the

compressor.

• Disconnect and wind up the power cord.

• Clean the ventilation openings on the motor enclosure with a

damp cloth.

• Drain all moisture from the tank.

• Pull the pressure safety valve to release all pressure from the

tank.

• Cover the entire unit to protect it from moisture and dust.

• Store the air compressor in a clean and dry location.

• In cold weather, store the compressor in a warm building when

it is not in use. This will reduce problems related to starting the

motor and the freezing of water condensation.

• Before starting compressor, pull the ring on the safety valve (D) to make sure

that the safety valve operates freely. If the valve is stuck or does not operate

smoothly, contact a trained service technician.

20 21

TROUBLESHOOTING

The motor does

not run or start.

The power cord is not plugged in. Plug the power cord into a grounded outlet.

The ON/OFF switch is in the

OFF position. Set the power switch to the ON position.

The extension cord is the wrong

wire gauge or is too long.

Check extension cord information (page 7)

for the proper wire gauge and cord length.

The motor’s thermal overload

protection has tripped.

Turn the air compressor off, unplug the

power cord and wait until the motor has

cooled down. Plug in the power cord only

after the motor has cooled down, and wait

at least 15 minutes to make sure the thermal

overload protector has recovered.

A fuse has blown or a circuit

breaker has been tripped.

Replace the fuse or reset the circuit breaker.

Verify that the fuse has the proper amperage.

Check for low voltage conditions.

Disconnect any other electrical appliances

from the circuit or operate the compressor

on a dedicated circuit.

The air tank pressure exceeds

the preset pressure switch limit.

The motor will start automatically when the

tank pressure drops below the cut-in

pressure.

The safety valve is stuck open. Clean or replace the safety valve.

Electrical connections are loose.

Have the compressor serviced by a qualiﬁed

technician.

The motor, capacitor, or safety

valve is defective.

Have the compressor serviced by a qualiﬁed

technician.

The switch does not shut off

the motor when the air

compressor reaches the cut-out

pressure and the safety valve

activates.

Set the ON/OFF switch to the OFF position.

If the motor does not shut off, unplug the air

compressor. If the ON/OFF switch is

defective, replace it.

The compressor’s capacity

is not enough.

Check the air requirements of the accessory

that is being used. If it is higher than the

CFM (Cubic Feet per Minute and pressure

supplied by the compressor, page 4), a

larger capacity air compressor is needed.

Most accessories are rated at 25% of actual

CFM while running continuously.

PROBLEM POSSIBLE CAUSES SOLUTIONS

The motor runs

continuously

when the

ON/OFF switch

is in the ON

position.

PROBLEM POSSIBLE CAUSES SOLUTIONS

The regulator

does not

regulate the

pressure.

The regulator or its internal parts

are dirty or damaged. Replace the regulator.

The pressure is

low or there is

not enough air.

There is a leak at one of the

ﬁttings.

Check the ﬁttings with soapy water. Tighten

or reseal leaking ﬁttings (apply plumber's tape

on threads). Do not over-tighten.

The tank drain valve is open. Close the drain valve.

The air intake is restricted. Clean or replace the air ﬁlter element.

Prolonged excessive use of air. Decrease the amount of air used.

There is a hole in the air hose. Check the air hose and replace it if necessary.

The tank leaks. Replace the tank immediately. Do not attempt

to repair it.

The check valve/pressure relief valve

/pressure regulating valve is leaking.

Check for worn parts and replace them if

necessary.

There is

moisture in the

discharge air.

There is condensation in the air

tank caused by a high level of

atmospheric humidity or because

the air compressor has not been

running long enough.

Drain the air tank after each use. Drain the air

tank more often in humid weather and use an

air-line ﬁlter.

The

compressor

overheats.

The ventilation is inadequate. Relocate the compressor to an area with cool,

dry and well-circulated air.

Cooling surfaces are dirty. Clean all cooling surfaces on the pump and the

motor thoroughly.

The check valve is leaking. Replace worn parts and reassemble using new

plumber's tape.

model no. 058-1980-4 | contact us 1-888-670-6682

103

104

105

106

107

22 23

EXPLODED VIEW

TSILSTRAP

If any parts are missing or damaged, or if you have any questions, please call our toll-free

helpline at 1-888-670-6682.

DescriptionNo. Qty.

101

Exhaust pipe

Back panel

Inside buckle handle

Power cord

Socket

Check valve

Right panel

Drain pipe

Air tank foot pad

Swivelling castor

Tracheal hook

Tracheal sleeve (with magnetic)

Base plate

Swivelling Castor (with brake)

Drain valve

DC power

Power ﬁxing bracket

Screw ST4.8x10

Screw ST2.9

Bolt M5

Screw M5

Nut M6

Bolt M8

Screw M4

102 2

Air tank

Solenoid valve

Shock pad

Four-way ﬁtting

Metal tube

Pressure switch

Pressure regulator knob

ON/OFF switch

Safety valve

Right angle elbow

Tank pressure gauge

Outlet pressure gauge

Left panel

Air pressure regulator

Air ﬁlter

End cap

Air outlet

Motor assembly

DC Fan

Capacitor shroud

Capacitance

Right angle elbow

Capacitor ﬁxing ring

Crimping cap

model no. 058-1980-4 | contact us 1-888-670-6682

24 25

WARRANTY

These warranties are subject to the following conditions and limitations:*

A. A bill of sale verifying the purchase and purchase date must be provided;

B. Defects in workmanship and material to be assessed and determined by the Service Provider;

C. This warranty will not apply to any product or part thereof which is worn or broken or which has

become inoperative due to abuse, misuse, accidental damage, neglect or lack of proper installation,

operation or maintenance (as outlined in the applicable owner’s manual or operating instructions);

D. This warranty does not apply to normal wear and tear or to expendable parts or accessories (including

life span and are expected to become inoperative or unusable after a reasonable period of use;

E. This warranty will not apply to routine maintenance and consumable items such as, but not limited to,

adjustments;

F. This warranty excludes the following components that may accompany your product:

(1) The carrying case, which is guaranteed for a period of one (1) year from the date of original retail purchase

against defects in workmanship and materials.

G. This warranty will not apply where damage is caused by repairs made or attempted by others

(i.e., persons not authorized by the manufacturer), and any such unauthorized repairs or attempted

repairs shall void this warranty in its entirety;

H. This warranty will not apply to any parts other than original parts, except to the extent that the retailer

or manufacturer or persons authorized by either of them have repaired or replaced them;

I. This warranty will not apply to any product that was sold to the original purchaser as a reconditioned

J. This warranty will not apply to any product or part thereof if any part from another manufacturer is

installed therein or any repairs or alterations have been made or attempted by unauthorized persons;

scratches, dents, paint chips, or to any corrosion or discolouring by heat, abrasive and chemical cleaners;

which shall be covered under that product manufacturer’s warranty, if any;

product warranty conditions and related time period as initiated by the original date of purchase; if product

is purchased in Quebec, the warranty term will be extended for a period equal to the time during which the

default to new product warranty conditions; and

N. The retailer and manufacturer’s sole obligation and the purchaser’s sole remedy under this warranty shall

be as set out herein. The warranties contained herein are not transferable and are given only to the

purchaser. FURTHER, THE WARRANTIES SET OUT HEREIN ARE IN LIEU OF ALL OTHER WARRANTIES OR

CONDITIONS, WHETHER EXPRESS, IMPLIED OR STATUTORY (INCLUDING SUCH AS ARISE UNDER THE

SALE OF GOODS ACT OR THE INTERNATIONAL SALE OF GOODS ACT), ARISING OUT OF A COURSE OF

DEALING OR USAGE OF TRADE OR OTHERWISE, INCLUDING, SUBJECT TO APPLICABLE LAW, ANY IMPLIED

WARRANTIES OR CONDITIONS OF MERCHANTABILITY, MERCHANTABLE QUALITY, FITNESS OR ADEQUACY

FOR A PARTICULAR PURPOSE OR USE, AND ALL OTHER SUCH WARRANTIES ARE EXPRESSLY DISCLAIMED

BY THE RETAILER AND MANUFACTURER.

3-Year Limited Warranty

This MAXIMUM® product is guaranteed for a period of three (3) years from

the date of original retail purchase against defects in workmanship and

materials.

Subject to the conditions and limitations described below, this product,

if returned to us with proof of purchase within the stated warranty period

and if covered under this warranty, will be repaired or replaced (with the

MAXIMUM Canada authorised repair centre (“Service Provider”). We will bear the

cost of any repair or replacement and any costs of labour relating thereto.

DAYS

JOURS

DE SATISFACTION

GARANTIE

SATISFACTION

GUARANTEE

YEAR

DE GARANTIE

SUR RÉPARATIONS

REPAIR

WARRANTY

YEAR

ANS

DE GARANTIE

LIMITÉE

LIMITED

WARRANTY

Quebec retailer possesses the product in attempt fulﬁll warranty obligations; replaced product will not

model no. 058-1980-4 | contact us 1-888-670-6682

WARRANTY

26 27

WARRANTY

return it within 90 days from the date of purchase with proof of purchase for exchange or a full refund.

province to province. The provisions contained in this warranty are not intended to limit, modify, take

away from, disclaim or exclude any statutory warranties set forth in any applicable provincial or federal

legislation.

In addition to the 3-Year Limited Warranty, this MAXIMUM product is covered by our:

1-Year Repair Warranty

90-Day Satisfaction Guarantee

MAXIMUM Canada will maintain this product and repair parts that have worn beyond reasonable

The following are excluded from this one (1) year Repair Warranty:

a) Missing or damaged parts or components that are a result of abuse or misuse; and

b) Any wear and tear to non-critical parts or accessories that do not affect the core function of the product.

Additional Limitations * Notice to Consumer

This warranty applies only to the original purchaser and may not be transferred.

This warranty applies for a period of three (3) years from the date of original retail purchase, as indicated on

the bill of sale.

Neither the retailer, MAXIMUM Canada, nor the manufacturer shall be liable for any other expense,

loss or damage, including, without limitation, any indirect, incidental, consequential or exemplary

damages arising in connection with the sale, use or inability to use this product.

Under no circumstances shall the retailer, MAXIMUM Canada, or manufacturer be liable to the

purchaser for any claim for (a) indirect, special, punitive, incidental, exemplary, or consequential

economic loss of the purchaser; (c) exemplary, aggravated or punitive damages howsoever incurred;

(d) contribution or set-off in respect of any claims against the purchaser; (e) any damages whatsoever

relating to third party products or services or the purchaser’s materialsor; (f) any damages whatsoever

relating to interruption, delays, errors or omissions; in each case under any theory of law or equity,

arising out of or in any way related to this warranty, even if advised of the possibility thereof.

Notwithstanding any provision herein or entitlement of the purchaser at law, in equity or otherwise,

in no event shall the liability of the retailer or manufacturer under this warranty, whether in contract,

tort, product liability or otherwise, exceed, in the aggregate, the amount paid by the purchaser to the

retailer for the product to which this warranty applies.

Made in China

Imported by MAXIMUM Canada Toronto, Canada M4S 2B8

;

MAXIMUM®product for any reason, you can

model no. 058-1980-4 | contact us 1-888-670-6682

Veuillez lire attentivement ce guide d’utilisation avant

d’utiliser cet article et le conserver aux fins de consultation

ultérieure.

GUIDE

D’UTILISATION

10 gallons US (38 L)

Compresseur d'air

ULTRA-SILENCIEUX

N° de modèle : 058-1980-4

TABLE DES MATIÈRES

FICHE TECHNIQUE 4

CONSIGNES DE SÉCURITÉ 5

SCHÉMA DES PIÈCES CLÉS 8

LISTE DES PIÈCES CLÉS 9

USAGE PRÉVU 10

ASSEMBLAGE 12

CONSIGNES D’UTILISATION 14

ENTRETIEN 18

DÉPANNAGE 20

VUE ÉCLATÉE 22

CONSERVEZ CES CONSIGNES

Conservez ce guide d'utilisation pour toute consultation ultérieure. Si vous remettez ce

produit à un tiers, ce guide d'utilisation doit l'accompagner.

LISTE DES PIÈCES 23

GARANTIE 24

REMARQUE :

Si des pièces sont manquantes ou endommagées, ou pour toute question, veuillez communiquer avec

notre service d’assistance téléphonique sans frais au 1 888 670-6682.

4 5

CONSIGNES DE SÉCURITÉ

FICHE TECHNIQUE

* PI³/MIN : pied cube par minute

1,3 HP

4 PI³/MIN À 40 LB/PO²

3 PI³/MIN À 90 LB/PO²

120

150

10 GALLONS US (38 L)

SANS HUILE

À INDUCTION

120 V, 60 Hz, 8,5 A

132 lb 4 1/2 oz (60 kg)

SJOW 16 AWG/72 po (1,83 m)

PUISSANCE EN MARCHE

CAPACITÉ DU RÉSERVOIR

DÉBIT D'AIR

PRESSION D'ENCLENCHEMENT (LB/PO²)

PRESSION DE DÉCLENCHEMENT (MAXIMALE) (LB/PO²)

MODÈLE DE POMPE

MOTEUR

ALIMENTATION

POIDS

CORDON D'ALIMENTATION

Le présent guide contient des renseignements relatifs à la SÉCURITÉ PERSONNELLE

et à la PRÉVENTION DES PROBLÈMES D’ÉQUIPEMENT. Il est très important de lire

attentivement et de bien comprendre ce guide avant d’utiliser le produit. Les symboles

ci-dessous servent à indiquer cette information.

IMPORTANT!

Renseignements relatifs à l'installation, à l'utilisation ou à l'entretien qui sont importants mais qui ne sont pas

associés à des dangers.

ATTENTION!

Danger potentiel qui peut provoquer des blessures moyennement graves ou des dommages à l’équipement.

AVERTISSEMENT!

Danger potentiel qui pourrait entraîner des blessures graves ou la mort.

DANGER!

Danger potentiel qui entraînera de graves blessures ou la mort.

Conseils de sécurité

1. RISQUE D'INCENDIE OU D'EXPLOSION. Ne pulvérisez pas de liquides ou de peintures

inﬂammables ou combustibles près d'étincelles, de ﬂammes, de veilleuses ou dans un endroit

clos. La zone où vous pulvérisez doit être adéquatement aérée. Gardez le compresseur à une

distance d'au moins 20 pi (6 m) de l'endroit où vous pulvérisez. Ne transportez pas et n'utilisez

pas le compresseur ou tout autre appareil électrique près de l'endroit où vous pulvérisez.

Ne fumez pas lorsque vous pulvérisez. Prévoyez un tuyau d'au moins 25 pi (7,6 m) pour

raccorder le pistolet pulvérisateur au compresseur.

2. RISQUE DE CHOC ÉLECTRIQUE. N'exposez pas l'appareil à la pluie ou à l'eau. Rangez-le à

l'intérieur. Tension dangereuse. Débranchez l'appareil de sa source d'alimentation avant

d'effectuer toute réparation ou tout entretien. Le compresseur doit être branché à une prise

mise à la terre. N'utilisez pas d'adaptateur branché à une prise mise à la terre.

RISQUE D'ÉCLATEMENT. Vériﬁez la pression nominale maximale dans le manuel ou sur

l'étiquette d'identiﬁcation. La pression de sortie du compresseur doit être régulée de manière

à ne pas dépasser la pression nominale maximale. Libérez toute pression dans le tuyau avant

de retirer ou de ﬁxer des accessoires. Assurez-vous que le régulateur est réglé de manière à

ce que la pression de sortie du compresseur soit inférieure à la pression de fonctionnement

maximale du pistolet pulvérisateur ou de l'outil. Avant de démarrer le compresseur, tirez sur

la bague de la soupape de sécurité pour vous assurer que la soupape se déplace librement

(voir schéma page 19). Vidangez l'eau du réservoir après chaque utilisation. Ne tentez pas de

souder ou de réparer le réservoir.

RISQUE DE BLESSURES. Ne pulvérisez jamais de l'air ou tout autre matériau comprimé

vers vous-même ou d'autres personnes.

FICHE TECHNIQUE

N° de modèle : 058-1980-4 | Communiquez avec nous au 1 888 670-6682

56 dB(A)

NIVEAU SONORE

5. RISQUE D'ÉCLATEMENT. Ne réglez pas le pressostat ni la soupape de

sûreté pour quelque raison que ce soit. Ils ont été préréglés en usine

pour correspondre à la pression maximale du compresseur. Toute

modiﬁcation au pressostat ou à la soupape de sûreté peut entraîner des

blessures ou des dommages matériels.

6 7

CONSIGNES DE SÉCURITÉ

AVERTISSEMENT!

Tirez l'anneau situé sur la soupape de sûreté tous les jours pour vous assurer que cette dernière

fonctionne adéquatement.

Le compresseur doit se trouver dans une zone adéquatement aérée aﬁn qu'il puisse refroidir, à une

distance d'au moins 12 po (31 cm) du mur le plus près.

Protégez le tuyau à air et le cordon d'alimentation contre les dommages et la perforation. Examinez-les

toutes les semaines pour repérer toute trace d'usure ou de dommages et remplacez-les au besoin.

Portez toujours une protection auditive lorsque vous utilisez un compresseur d'air. Le non-respect de

cette consigne peut conduire à une perte auditive.

Ne transportez pas le compresseur lorsqu'il est en marche.

Ne mettez pas le compresseur en marche s'il n'est pas dans une position stable.

Ne mettez pas le compresseur en marche sur un toit ou dans une position élevée qui pourrait permettre

à l'appareil de tomber ou de se renverser.

Remplacez toujours un manomètre endommagé avant de faire fonctionner l'appareil de nouveau.

WARNING!

CALIBRE DE LA RALLONGE (CALIBRAGE AMÉRICAIN NORMALISÉ DES FILS)

Longueur de la rallonge

25 pi (7,6 m) 50 pi (15 m) 75 pi (23 m) 100 pi (30 m) 150 pi (46 m) 200 pi (60 m)

0 – 5 16 16 16 14 12 12

5,1 – 8 16 16 14 12 10 —

8,1 – 12 14 14 12 10 — —

12,1 – 15 12 12 10 10 — —

15,1 – 20 10 10 10 — — —

INTENSITÉ

NOMINALE

6. RISQUE DE BRÛLURES. La pompe et le collecteur produisent des

températures élevées. Pour éviter les brûlures ou toute autre blessure,

ne touchez pas à la pompe, au collecteur ou au tube de transfert lorsque

le compresseur est en marche. Laissez les composantes refroidir avant

de manipuler l'appareil ou d'y apporter toute réparation ou tout entretien.

Éloignez les enfants du compresseur en tout temps.

7. RISQUE D’INHALATION. Soyez certain de lire toutes les étiquettes

lorsque vous pulvérisez de la peinture ou des matières toxiques, et suivez

toutes les consignes de sécurité. Utilisez un masque respiratoire en cas de

risque d'inhalation de ce que vous pulvérisez. Aussi, n'inhalez JAMAIS

l'air comprimé directement produit par un compresseur.

Rallonges

Lorsque la distance entre le compresseur et la prise électrique augmente, vous devez utiliser une

rallonge de calibre supérieur. L'utilisation de rallonges de calibre insufﬁsant entraînera une

importante chute de tension, et par conséquent, une perte d'alimentation et des dommages à

l'appareil. Consultez le tableau ci-dessous pour déterminer le calibre minimal recommandé

pour les rallonges.

Calibre minimal recommandé pour les rallonges* (120 V)

* Selon une limitation de la chute de tension du secteur à 5 V à 150 % de l'intensité nominale.

Plus le calibre est bas, plus la capacité du cordon est élevée. Par exemple, un cordon de

calibre 14 peut transmettre un courant plus élevé qu’un cordon de calibre 16. Lorsque vous

utilisez plus d'une rallonge pour atteindre la longueur totale, assurez-vous que chaque cordon

correspond au moins au calibre minimal exigé.

Lignes directrices relatives à l'utilisation des rallonges

•

Si vous utilisez une rallonge à l'extérieur, assurez-vous que le sufﬁxe « W-A » (« W » au Canada)

ﬁgure sur la rallonge pour indiquer qu'elle convient à un usage à l'extérieur.

Tenez vos rallonges à l'écart des objets pointus ou tranchants, de la chaleur excessive et des

endroits humides ou mouillés.

•Assurez-vous que votre rallonge est correctement câblée et en bon état. Remplacez toujours

une rallonge endommagée ou faites-la remplacer par un électricien qualiﬁé avant de l'utiliser.

8. RISQUE DE BLESSURE À L'ŒIL. Portez des lunettes de sécurité ANSI Z87.1

ou CSA Z94.3 lorsque vous utilisez un compresseur d'air. Ne pointez pas une

buse ou un pulvérisateur quelconque en direction d'une personne ou d'une partie

du corps.Des blessures graves peuvent se produire si le jet pénètre la peau.

9. RISQUE AUDITIF. Portez toujours des protecteurs d'oreilles lors de l'utilisation d'un

compresseur d'air. Le non-respect de cette directive peut entraîner la perte d'audition.

N° de modèle : 058-1980-4 | Communiquez avec nous au 1 888 670-6682

8 9

SCHÉMA DES PIÈCES CLÉS

LISTE DES PIÈCES CLÉS

AVERTISSEMENT!

Ne dépassez pas la pression d'utilisation maximale de l'outil.

AVERTISSEMENT!

Ne tentez pas d'ouvrir le robinet de vidange lorsque la pression d'air dans le réservoir est supérieure à 10 lp/po².

Fiche

Broche de terre

Prises mises

à la terre

A. MOTEUR ÉLECTRIQUE : Le moteur sert à alimenter la pompe. Il est doté d’un dispositif de protection

contre la surcharge. En cas de surchauffe du moteur pour quelque raison que ce soit, le dispositif de

B. POMPE DU COMPRESSEUR D'AIR : La pompe comprime l’air et le décharge dans le réservoir à l’aide

du piston qui monte et descend dans le cylindre.

C. INTERRUPTEUR D'ALIMENTATION : Il sert à mettre le compresseur en marche et à l’éteindre. Il est

actionné manuellement et lorsqu’il est en position de marche (ON), il permet au moteur de démarrer si la

pression dans le réservoir d’air est inférieure à la pression d’enclenchement réglée en usine, et permet au

moteur d’arrêter si la pression dans le réservoir d’air atteint la pression de déclenchement réglée en usine.

Assurez-vous de placer cet interrupteur d'alimentation en position d’arrêt (OFF) lorsque vous n’utilisez pas

le compresseur et avant de le débrancher.

D. SOUPAPE DE SÛRETÉ : Cette soupape sert à éviter les pannes de système en libérant la pression du

système lorsque celle-ci atteint le niveau préréglé, si le pressostat n’a pas éteint le moteur. Elle s’ouvre

automatiquement ou peut être actionnée manuellement en tirant sur l’anneau de la soupape.

E. RÉGULATEUR DE PRESSION D'AIR : Le régulateur sert à régler la pression qui circule dans le tuyau

raccordé à l’outil utilisé. Tournez le bouton dans le sens horaire pour augmenter la pression et dans le sens

antihoraire pour la diminuer.

F. MANOMÈTRE DU RÉSERVOIR : Le manomètre sert à mesurer la pression de l’air à l’intérieur du

réservoir. Il ne peut pas être réglé par l’utilisateur et n'indique pas la pression dans le tuyau.

G. CONTRÔLEUR DE LA PRESSION : Le contrôleur sert à mesurer la pression de sortie régulée.

H. SORTIE D'AIR : La prise est raccordée au tuyau d’air de 1/4 po (6,4 mm) NPT.

I. ROBINET DE VIDANGE DU RÉSERVOIR D'AIR : Le robinet de vidange sert à retirer l’humidité

accumulée dans le réservoir d’air après avoir éteint le compresseur.

J. RÉSERVOIR D'AIR : Le réservoir sert à contenir l’air comprimé.

K. CORDON D'ALIMENTATION : Ce compresseur doit être alimenté par un circuit nominal de 120 V mis à

doit être utilisé avec ce compresseur.

MOTEUR ÉLECTRIQUE (A)

SOUPAPE DE SÛRETÉ (D)

INTERRUPTEUR

D'ALIMENTATION (C) SORTIE D'AIR (H)

MANOMÈTRE DU RÉSERVOIR (F)

CORDON D'ALIMENTATION (K)

POMPE DU COMPRESSEUR

D'AIR (B)

RÉGULATEUR DE

PRESSION D'AIR (E)

CONTRÔLEUR DE PRESSION (G)

ROBINET DE VIDANGE

DU RÉSERVOIR D'AIR (I)

RÉSERVOIR D'AIR (J)

N° de modèle : 058-1980-4 | Communiquez avec nous au 1 888 670-6682

L. TUYAU D'ÉVACUATION: Le tuyau de drainage est connecté à la valve de drainage directement pendant

l'expédition, et doit être utilisé pour drainer l'air et la pollution facilement.

TUYAU D'ÉVACUATION (L)

10 11

USAGE PRÉVU

•

AVERTISSEMENT!

Ce compresseur d’air n’est pas destiné à un fonctionnement continu ni à des usages commerciaux

illimités et ne peut être utilisé qu’en milieux secs. Ce compresseur est conçu pour être utilisé à un

intervalle maximal de 30 minutes et doit être en repos pendant 30 minutes avant d’être utilisé de

nouveau. Ne dépassez pas la durée d'utilisation maximale de l'outil.

Avant de commencer

Compresseur et outil pneumatique compatibles : utilisation et fonctionnement adéquats

graissage en passant par le nettoyage du moteur. La conception de 10 gallons (38 L) offre une pression optimale.

Elle se caractérise par une pompe sans huile ainsi qu'un moteur à induction de 1,3 HP pour un fonctionnement

puissant. Les consignes décrites dans ce guide ne s'appliquent qu'au compresseur d'air de 10 gallons (38 L) à

une pression maximale de 150 lb/po². Cet appareil a été exclusivement conçu et construit pour un usage domes-

tique.

Assurez-vous d’utiliser des outils pneumatiques qui conviennent à votre compresseur d’air ultra-silencieux

nécessaires aux outils sans avoir à fonctionner en continu. L’utilisation d’outils ou d’une combinaison d’outils

qui nécessitent, ensemble ou séparément, une quantité d’air supérieure à ce que le compresseur d’air peut fournir

entraînera l’annulation de la garantie du compresseur d’air.

MAXIMUM

MD. Veillez à ce que le compresseur d’air utilisé puisse fournir le volume, la pression et le débit d’air

Outil pneumatique

Tableau de compatibilité d’outils

Fonctionnement

continu

Usage

déconseillé

Fonctionnement

intermittent

Cloueuse à charpente

Cloueuse à plancher

Meuleuse à matrices/d’angle

Meuleuse/cliquet pneumatique

Outil à tronçonner

Pistolet à peinture

(calibre 18)

en 1/agrafeuse

Cloueuse à toiture

Clé à chocs

Perceuse/marteau/ciseau/

cisailles

Ponceuse/polisseuse

Pistolet graisseur et à calfeutrer

N° de modèle : 058-1980-4 | Communiquez avec nous au 1 888 670-6682

La page est en cours de chargement...

Maximum 10-Gallon Quiet Cabinet Le manuel du propriétaire

Marque: Maximum

Modèle: 10-Gallon Quiet Cabinet

Catégorie: Compresseurs d'air

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Maximum 10-Gallon Quiet Cabinet Owner's manual

Documents connexes

Maximum 058-9317-8 Manuel utilisateur

Maximum 10-Gallon Quiet Cabinet Le manuel du propriétaire

Maximum 10-Gallon Quiet Cabinet Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents