Frigidaire FGIC3067MB Manuel utilisateur

Marque: Frigidaire

Modèle: FGIC3067MB

Catégorie: Plaques de cuisson

Taper: Manuel utilisateur

Ce manuel convient également à

TABLE OF CONTENTS

www.frigidaire.com USA 1-800-944-9044 www.frigidaire.ca Canada 1-800-265-8352

All about the

Use & Care

of your Cooktop

Welcome & Congratulations ...................................2

Important Safety Instructions .................................3

Cooktop Features ..................................................5

Quick Instructions to Set your Cooktop Controls ......6

Before Using the Cooktop ......................................7

318205604 (March 2015) Rev. C

Setting Cooktop Controls .......................................9

Care & Cleaning ..................................................13

Before You Call ..................................................15

Notes .................................................................17

Major Appliance Warranty ....................................18

WELCOME & CONGRATULATIONS



NOTE

Please attach sales receipt here for future reference.

Please record your model and serial numbers

below for future reference.

Model Number:

Serial Number:

Purchase Date:

Printed in China

Congratulations on your purchase of a new appliance! At

Electrolux Home Products, we are very proud of our

product and are completely committed to providing you

with the best service possible. Your satisfaction is our

number one priority.

We know you’ll enjoy your new appliance and Thank You

for choosing our product. We hope you consider us for

future purchases.

PLEASE CAREFULLY READ AND SAVE THESE

INSTRUCTIONS

This Use & Care Manual contains general operating

instructions for your appliance and feature information

for several models. Your product may not have

all the described features. The graphics shown are

representative. The graphics on your appliance may not

look exactly like those shown. These instructions are not

meant to cover every possible condition and situation

that may occur. Common sense and caution must be

practiced when installing, operating and maintaining any

appliance.

Product Registration

Serial Plate Location

Cooktop Serial

Plate Location

The PRODUCT

REGISTRATION CARD

should be ﬁ lled in completely,

signed and returned to

Electrolux Home Products.

IMPORTANT SAFETY INSTRUCTIONS

WARNING

This symbol will help alert you to situations that

may cause serious bodily harm, death or property

damage.

IMPORTANT

IMPORTANT indicates installation, operation or

maintenance information which is important but not

hazard-related.

CAUTION

This symbol will help alert you to situations that

may cause bodily injury or property damage.

DEFINITIONS

This is the safety alert symbol. It is used to alert

you to potential personal injury hazards. Obey all safety

messages that follow this symbol to avoid possible injury

or death.

Electrical Code No. 70 - latest edition in the

United States, or CSA C22.1, Part 1 in Canada, and

local code requirements. Install only per installation

instructions provided in the literature package for this

appliance.

Ask your dealer to recommend a qualiﬁ ed technician and

an authorized repair service. Know how to disconnect the

electrical power to the appliance at the circuit breaker or

fuse box in case of an emergency.

• User Servicing. Do not repair or replace any part of

the appliance unless speciﬁ cally recommended in

the manuals. All other servicing should be done only by

a qualiﬁ ed technician to reduce the risk of personal injury

and damage to the appliance.

• Never modify or alter the construction of an

appliance such as removal of panels, wire covers

or any other permanent part of the appliance.

• Storage on Appliance. Flammable materials should

not be stored near surface units. This includes paper,

plastic and cloth items, such as cookbooks, plasticware

and towels, as well as ﬂ ammable liquids. Do not store

explosives, such as aerosol cans, on or near the appliance.

Flammable materials may explode and result in ﬁ re or

property damage.

• Do not leave children alone. Children should not

be left alone or unattended in the area where an

appliance is in use. They should never be allowed to

sit or stand on any part of the appliance.

This unit has been tested and found to comply with the

limits for a class B digital device, pursuant to Part 18 of the

FCC rules. These limits are designed to provide reasonable

protection against harmful interference in a residential in-

stallation. This unit generates, uses and can radiate radio

frequency energy and, if not installed and used in accor-

dance with the instructions, may cause harmful interference

to radio communications. However there is no guarantee

that interference will not occur in a particular installation.

If this unit does cause harmful interference to radio or tele-

vision reception, which can be determined by turning the

unit off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antennae.

• Increase the distance between the unit and receiver.

• Connect the unit into an outlet or a circuit different from

that to which the receiver is connected.

• Remove all tape and packaging wrap before using

the appliance. Destroy the carton and plastic bags

after unpacking the appliance. Never allow children

to play with packaging material.

• Proper Installation. Be sure your appliance is

properly installed and grounded by a qualiﬁ ed

technician in accordance with the National

WARNING

To reduce the risk of ﬁ re, electrical shock, or injury

when using your electric cooktop, follow basic

precaution including the following:

WARNING

Stepping or leaning on this cooktop can result in

serious injuries and may also cause damage to the

cooktop. Do not allow children to climb or play around

the cooktop.

CAUTION

Do not store items of interest to children in the

cabinets above the appliance. Children climbing on

the cooktop to reach items could be seriously injured.

Read all instructions before using this appliance.

Save these instructions for future reference.

WARNING

Persons with a pacemaker or similar medical device should

exercise caution using or standing near an induction unit

while it is in operation, as the electromagnetic ﬁ eld may

affect the working of the pacemaker or similar medical

device. It would be advisable to consult your Doctor or

the pacemaker or similar medical device manufacturer

about your particular situation.

IMPORTANT SAFETY INSTRUCTIONS

• DO NOT TOUCH SURFACE UNITS OR AREAS NEAR

THESE UNITS. Surface units may be hot even though

they are dark in color. Areas near surface units may

become hot enough to cause burns. During and after

use, do not touch, or let clothing or other ﬂ ammable

materials touch these areas until they have had sufﬁ cient

time to cool. Among these areas are the cooktop and

areas facing the cooktop.

• Wear Proper Apparel. Loose-ﬁ tting or hanging

garments should never be worn while using the

appliance. Do not let clothing or other flammable

materials contact hot surfaces.

• Do Not Use Water or Flour on Grease Fires.

Smother the ﬁ re with a pan lid, or use baking

soda, a dry chemical or foam-type extinguisher.

• When heating fat or grease, watch it closely. Fat or

grease may catch ﬁ re if allowed to become too hot.

• Utensil Handles Should Be Turned Inward and

Not Extend Over Adjacent Surface Units. To reduce

the risk of burns, ignition of ﬂ ammable materials, and

spillage due to unintentional contact with the utensil.

• Never Leave Surface Units Unattended. Boilovers

cause smoking and greasy spillovers that may ignite, or

a pan that has boiled dry may melt.

• Protective Liners. Do not use aluminum foil to line

any part of the appliance. Only use aluminum foil as

recommended for baking if used as a cover placed on

the food. Any other use of protective liners or aluminum

foil may result in a risk of electric shock or ﬁ re or short

circuit.

• Glazed Cooking Utensils. Only certain types of glass,

glass/ceramic, ceramic, earthenware, or other glazed

utensils are suitable for range top service without

breaking due to the sudden change in temperature.

Check the manufacturer’s recommendations for cooktop

use.

• Ventilating hood. The ventilating hood above your

cooking surface should be cleaned frequently, so the

grease from cooking vapors does not accumulate on the

hood or ﬁ lter.

• Do Not Use Decorative Surface Element Covers.

If an element is accidentally turned on, the decorative

cover will become hot and possibly melt. Burns will occur

if the hot covers are touched. Damage may also be done

to the appliance.

• Do Not Clean or Operate a Broken Cooktop. If

cooktop should break, cleaning solutions and spillovers

may penetrate the broken cooktop and create a

risk of electric shock. Contact a qualiﬁ ed technician

immediately.

• Clean Cooktop with Caution. If a wet sponge or cloth

is used to wipe spills on a hot cooking area, be careful to

avoid a steam burn. Some cleaners can produce harmful

fumes if applied to a hot surface.

• Do Not Place Hot Cookware on Cold Cooktop

Glass. This could cause glass to break.

• Do not slide pan across the cooktop surface. They

may scratch the cooktop surface.

• Do Not Let Pans Boil Dry. This may cause permanent

damage in the form of breakage, fusion, or marking

that can affect the ceramic-glass cooktop. (This type of

damage is not covered by your warranty).

IMPORTANT SAFETY NOTICE

The California Safe Drinking Water and Toxic

Enforcement Act requires the Governor of California

to publish a list of substances known to the state to

cause cancer, birth defects or other reproductive harm,

and requires businesses to warn customers of potential

exposure to such substances.

IMPORTANT

Do not attempt to operate the cooktop during a

power failure. If the power fails, always turn off

the cooktop. If the cooktop is not turned off and the

power resumes, the cooktop will not operate and an error

message will be displayed.

WARNING

Never use your appliance for warming or heating

the room.

• Use Only Dry Pot holders. Moist or damp pot

holders on hot surfaces may result in burns from

steam. Do not let the pot holders touch hot surface

units. Do not use a towel or other bulky cloth instead of

a pot holder.

• Do Not Heat Unopened Food Containers. Buildup

of pressure may cause the container to burst and

result in injury.

IMPORTANT SAFETY INSTRUCTIONS FOR USING

YOUR COOKTOP

• Know which knob controls each surface unit.

• Clean the appliance regularly to keep all parts

free of grease that could catch ﬁ re. Exhaust fan

ventilation hoods and grease filters should be kept

clean. Do not allow grease to accumulate on hood or

ﬁ lter. Greasy deposits in the fan could catch ﬁ re. When

ﬂ aming food under the hood, turn fan on. Refer to hood

manufacturer's instructions for cleaning.

• Use Proper Pan Size. This appliance is equipped with

one or more surface units of different sizes. Select utensils

having ﬂ at bottoms large enough to cover the surface unit.

The use of undersized utensils will expose a portion of

the surface heating unit to direct contact and may result

in ignition of clothing. Proper relationship of utensil to

element will also improve efﬁ ciency.

COOKTOP FEATURES

Read these instructions carefully before using the cooktop

1. Left Rear Cooking Zone

2. Left Front Cooking Zone

3. Right Rear Cooking Zone

4. Right Front Cooking Zone

5. Center Rear Cooking Zone (Fig. 2 only)

6. Left Front Cooking Zone Control Pads

7. Left Rear Cooking Zone Control Pads

8. Center Cooking Zone Control Pads (Fig. 2 only)

9. Right Front Cooking Zone Control Pads

10. Right Rear Cooking Zone Control Pads

11. Main Cooktop Controls

12. Minute Timer Display Window

13. Minute Timer Setting Up/Down Arrow Key pads

14. Controls Lockout Key Pad

15. Warm & Hold Setting Key Pad

16. Cooktop Power Key Pad

17. Controls Lockout Indicator Light

18. Cooktop Power Indicator Light

19. Cooking Zone Power Level Display

(One for each cooking zone)

20. Decrease Power Key pads

(One for each cooking zone)

21. Increase Power Key pads

(One for each cooking zone)

22. Element On/Off Key Pad

(One for each cooking zone)

20. Element On/Off Indicator Light

(One for each cooking zone)

CAUTION

The Cooking Zones may appear to be cool while turned ON and after they have been turned OFF. The glass surface

may be HOT from residual heat transferred from the cookware and burns may occur.

Figure 2 - 36“ Model

Figure 3 - Main Cooktop Controls Figure 4 - Cooking Zone Controls

Figure 1 - 30“ Model

20 21

15 16

QUICK INSTRUCTIONS TO SET YOUR COOKTOP CONTROLS

To Set the Power Level

To Set the Keep Warm Feature

Press

keep

warm

To Power-Up Your Cooktop

Press and Hold

for 2 seconds :

To Set the Timer

Adjust by Pressing or Tapping

: or

To Lock / Unlock the Controls

Press and Hold

for 3 seconds :

To Stop the Timer

Press Simultaneously

: and

To Power-Up a Cooking Zone

Press

Adjust by Pressing or Tapping

low

To Power-Down a Cooking Zone

Press

The desired zone

must be active.

Use the Correct Cookware Type

The magnetic Cooking Zone sensors located below the

cooktop surface require the use of cookware made with

magnetic material in order to start the heating process on

any of the Cooking Zones.

When purchasing pans, look for cookware speciﬁ cally

identiﬁ ed by the manufacturer for use with Induction

cooktops. If you are not sure, use a magnet to test whether

the cookware type will work. If a magnet sticks to the

bottom of the cookware, the material type is correct for

Induction cooking (See Fig. 1).

Fig. 1

It is recommended to always use heavier high quality

stainless steel cookware on your Induction Cooktop

surface. This will greatly reduce the possibility of developing

scratches on the ceramic surface.

Even quality cookware can scratch the cooktop surface,

especially if cookware is slid over the ceramic cooktop

surface without being lifted up. Over time sliding ANY type

of cookware over the ceramic cooktop will likely alter the

overall appearance of the cooktop. Eventually the buildup

of scratches will make cleaning the surface difﬁ cult and

degrade the overall appearance of the cooktop.

Induction Cooktop Characteristics

A COOLER COOKTOP- A unique feature of the Induction

Cooktop is whether turned ON or OFF, the cooktop surface

remains cooler than standard ceramic cooktops.

CAUTION

The Cooking Zones may appear to be cool while turned

ON and after they have been turned OFF. The glass

surface may be HOT from residual heat transferred

from the cookware and burns may occur.

MAGNETIC DETECTOR- The coil sensor automatically

detects whether the pan is magnetic and eliminates ac-

cidental “turn-On.”

PAN SIZE DETECTION- The pan recognition sensor au-

tomatically detects and adapts the Cooking Zones to the

pan sizes in use.

EFFICIENT- Induction cooking heats faster while using

less energy. Induction power levels are quick to boil and

when simmering.

Selecting Surface Cooking Cookware

The cookware used with the Induction Cooktop should have

ﬂ at bottoms that make good contact with the entire surface

of the Cooking Zone. Check for ﬂ atness by rotating a ruler

across the bottom of the cookware (See Fig. 2). Be sure to

follow all the recommendations for using cookware.

Figure 2

Prior to using your cooktop for the ﬁ rst time, apply the

recommended cooktop cleaning creme to the ceramic

surface. Buff with a non-abrasive cloth or pad. This will

make cleaning easier when soiled from cooking. The special

cooktop cleaning cream leaves a protective ﬁ nish on the

glass to help prevent scratches and abrasions.

Also remember to:

• Use cookware made with the correct material type for

Induction Cooking.

• Use quality cookware with heavier bottoms for better heat

distribution allowing for more even cooking results.

• The pan size should match the amount of food being

prepared.

• Do not let pans boil dry. This may cause permanent

damage in the form of breakage, fusion, or marring that

can affect the ceramic cooktop. (This type of damage is

not covered by your warranty).

• Do not use dirty pans with grease buildup. Always use

pans that are easy to clean after cooking.

CAUTION

• The Cooking Zones may appear to be cool while

turned ON and after they have been turned OFF. The

glass surface may be HOT from residual heat transferred

from the cookware and burns may occur.

• DO NOT SLIDE Cookware across the cooktop surface.

Doing so may permanently damage the appearance of

the ceramic cooktop.

• DO NOT TOUCH HOT COOKWARE or PANS directly

with hands. Always use oven mitts or pot holders to

protect hands from burns.

BEFORE USING THE COOKTOP

Cookware Recommendations



NOTE

ANY one of the incorrect conditions listed above in Fig. 1

may be detected by the sensors located below the ceramic

cooktop surface. If the cookware does not meet any of

these conditions, one or more of the Cooking Zones will

not heat indicated by a ﬂ ashing power level in the digital

display for that affected zone. Correct the problems before

attempting to reactivate the cooktop.

Be sure to follow the following recommendations for

using cookware as shown:

INCORRECT CORRECT

• Cookware not centered on

Cooking Zone surface.

• Cookware centered cor-

rectly on Cooking Zone

surface.

• Curved or warped pan

bottoms or sides.

• Flat pan bottom & straight

sides.

• Pan does not meet the

minimum size required for

the Cooking Zone used.

• Pan size meets or exceeds

the recommended minimum

size for the Cooking Zone.

• Pan bottom rests on cook-

top trim or does not rest

completely on the cook-

top surface.

• Pan rests completely on

the Cooktop surface.

• Heavy handle tilts pan.

• Pan is properly balanced.

Fig. 1

BEFORE USING THE COOKTOP

Use the Correct Cookware Size

The Cooking Zones available on the Induction Cooktop

require a MINIMUM pan size to be used at each location.

The inner “X” of each Cooking Zone is your guide to the

correct MINIMUM pan size. The pan bottom must FULLY

cover the inner “X” for proper cooking to occur.

The thicker outer lines “+” at each Cooking Zone is helpful

to determine the pan MAXIMUM size. After centering the

cookware on the cooktop, make sure the cookware does

not extend more than 1/2” beyond the thicker line on the

Cooking Zone. The pan must make FULL contact on the

glass surface without the bottom of the pan touching the

metal cooktop trims.



NOTE

If a pan made of the correct material is centered properly

on any of the active Cooking Zones but is TOO SMALL,

the power level will ﬂ ash in the in the digital display and

the pan will not heat.



NOTE

NOTE: Pan bottom should not exceed 1/2” (13mm) from

outer Cooking Zone (Induction) “+”.

Max

Min

Using the Touch Control

Be sure that your ﬁ nger is placed in the center of the touch

pad. If the ﬁ nger is not placed on the center of a pad, the

cooktop may not respond to the selection made.

Lightly contact the pad with the ﬂ at part of your entire ﬁ ngertip.

Do not just use the narrow end of your ﬁ ngertip.

Controls Lock Pad

This feature allows the cooktop to be locked only when the

cooktop is switched to OFF. Touch and hold the LOCK key

pad for 3 seconds. A beep will sound and the Lock LED will

glow (Fig. 11). Once locked, no other displays will glow and

no Cooking Zones will activate. To turn the Controls Lock

OFF, touch and hold the LOCK key pad for 3 seconds. A

beep will sound, the Lock LED will turn OFF (Fig. 10) and

the cooktop may be used normally.

Cooking Zone On/Off Pad

Each of the Cooking Zones have separate ON/OFF key

pads. Once the Main Power key pad has been touched to

activate the cooktop, touch the corresponding Cooking

Zone ON/OFF key pad once to activate the Cooking Zone

needed. “-” will appear in the display and the ON/OFF LED

will glow (Fig. 6). If the corresponding UP/DOWN Arrow

key pad is not touched within 10 seconds, the request to

turn the Cooking Zone ON will cancel and the Cooktop will

go back to ready mode. To turn OFF a Cooking Zone, touch

the Cooking Zone ON/OFF key pad once. The Cooking Zone

LED will turn OFF (Fig. 5).

Power Level Settings

The Cooking Zones have separate Power Level displays.

Once active, the Cooking Zones will provide 15 Power Levels

to choose from. These include 1 (Fig. 7), 2, 2., 3, 3., 4, 4.,

5, 5., 6, 6. (Fig. 8), 7, 8, 9, p. Half power levels (available

between 2 and 7 power level) are indicated by lighting the

display decimal point (Fig. 8). The highest setting of P or

“Power Boost” provides approximately 139% power for 10

minutes (Fig. 9). After 10 minutes, the power level drops

to 9. Each key pad touch (or just holding down the Power

Level key pad) will scroll through all the available power

levels for any Cooking Zone quickly.

Fig. 1

Fig. 5

Fig. 10

Fig. 7

Fig. 3

Fig. 8 Fig. 9

Fig. 2

Fig. 6

Fig. 11

Residual Heat Message

Once any Cooking Zone has been used for cooking and

turned OFF, and if the cooktop surface temperature on

any of the Cooking Zones is still too HOT, “H” (Fig. 3) will

appear in the display for the affected Cooking Zone. The H

will continue to display if the temperature is still too HOT.

The Cooking Zones may appear

to be cool while turned ON and after they have

been turned OFF. But the glass surface may

be HOT from residual heat transferred from

the cookware and burns may occur if surface

is touched.

SETTING COOKTOP CONTROLS

Cooktop Power Pad

The Cooktop POWER key pad activates the entire Cooktop.

To power the cooktop, touch and hold the POWER key pad

for 2 seconds. A beep will sound and the Power LED will glow

(Fig. 2). The cooktop will be in a ready mode for 10 seconds.

If no other key pads are touched the Cooktop Main POWER

will turn OFF automatically. To turn the Main Power OFF touch

and hold the Main POWER key pad for 1 second. A beep will

sound and the Power LED will turn OFF (Fig. 1).

Fig. 4

Keep Warm Feature Message

Use the Keep Warm key pad to activate the

Warm setting for any of the Cooking Zones.

The ON/OFF key pad for the desired Cooking

Zone must be activated ﬁ rst, then touch the

Keep Warm key pad located in the Cooktop

Main Control area once to set. “L” (low heat)

should appear in the corresponding Cooking

Zone display (Fig. 4).

Pan Detection

All Cooking Zones will provide a Pan Detection message.

If a Cooking Zone is turned ON and no pan is detected, or

the pan has been moved or is not centered correctly, or is

not made of magnetic material, the power level will ﬂ ash

in the affected Cooking Zone display. If the situation is not

corrected, the zone will turn off after 3 minutes.

Setting Cooktop Controls

Operating the Cooking Zones

The Induction cooktop has four or ﬁ ve Cooking Zones

designed for cookware of various sizes. Be sure to place

cookware that meets the minimum and maximum pan size

requirements (see pages 7 & 8) for the Cooking Zone desired

and is best for the amount of food being prepared. Place

the cookware with the prepared food on the Cooking Zone

BEFORE setting any of the Cooktop controls.

NOTE: Touch once, or repeatedly touch the or key

pads to adjust or scroll through power levels at any time during

the cooking process (To scroll through the power levels touch

and hold the or key pads until the power level desired

is reached). Once the Cooking Zone power level has been set

the food will begin to heat at that level until the power level

is manually changed or power sharing is activated.

To Turn OFF the Cooking Zones:

1. Once cooking is complete, touch the key pad to

turn the Cooking Zone OFF.

2. The corresponding Cooking Zone ON/OFF LED located

above the key pad will turn OFF. A beep will sound

and the chosen Cooking Zone power level display will turn

off. If no other key pads are touched the Cooking Zone

will shut OFF.

3. When any Cooking Zone is OFF, the corresponding Cooking

Zone display may show H if the Cooking Zone temperature

is HOT. The display will continue to show H, even if the

Cooktop is switched OFF the display will continue to

indicate H as long as the cooking zone remains HOT.

The Cooking Zones may appear to be cool

while turned ON and after they have been turned OFF. But

the glass surface may be HOT from residual heat transferred

from the cookware and burns may occur.

Important operating notes:

• Fluids spilled or objects lying on the controls area of the

cooktop may cause the cooktop to display an error code

and turn OFF while cooking. Clean the spills or remove the

objects from the cooktop. The zone that was affected has

to be touched twice on the ON/OFF key. Once to clear the

stuck key and once to turn the zone back on.

• Be sure the cooktop vent holes are NOT blocked. If the vent

holes are blocked the cooktop internal sensor may shut OFF

the cooktop to avoid overheating the appliance.

• If the cookware or pan is moved from the center of any

active Cooking Zone for any reason, a sensor will detect the

situation and the cookware will no longer heat. The affected

Cooking Zone display will ﬂ ash the power level set for the

Cooking Zone. The Cooking Zone will remember the power

level setting for up to 3 minutes before the Cooking Zone

will automatically shut OFF.

SETTING COOKTOP CONTROLS

To Quickly Operate a Cooking Zone

1. Place the correct cookware containing prepared food

on the desired Cooking Zone.

2. Touch the main key pad for 2 seconds.

3. Touch the pad for the desired Cooking Zone.

4. Set the desired power level using the or pads.

5. When cooking is done, turn off the Cooking Zone by

touching its pad.

To Turn ON one or more Cooking Zones:

1. Place the prepared food using the correct type and size

cookware on the desired Cooking Zone. Be sure to center

the cookware on Cooking Zone completely covering the

minimum ring marked on the Zone surface.

2. Touch and hold the key pad for 2 seconds (or until

a long beep sounds). The Power LED located above the

key pad will turn ON. NOTE: If no other key pad is

touched within 10 seconds the request to Power ON the

cooktop will clear.

3. To start a Cooking Zones lightly touch the key pad

for the Cooking Zones needed. A beep will sound and the

chosen Cooking Zone power level display will show “-”

indicating no power level for the Zone has been set yet.

NOTE: If no other key pad is touched within 10 seconds

the request to Power ON the Cooktop Zone will clear.

4. Set the desired power level for the Cooking Zone by

touching either the or key pad. If the key

pad is touched the Cooking Zone will start at a “Power

Boost” maximum power level (the Cooking Zone display

will indicate “P” and the control will beep once). If the

key pad is touched once the Cooking Zone will start

at low (the Cooking Zone display will show “1 ” and the

control will beep once). PLEASE NOTE: If the cookware

requirements for the Cooking Zone (See pages 7 & 8)

are not met the sensors will detect a problem and the

display will ﬂ ash with the power level in the affected

Cooking Zone display. Any problems must be corrected

before proceeding.

Preheat Recommendations

When preheating a pan on the cooktop always watch

carefully. Whenever using the cooktop, always pay attention

to any items cooking and remain attentive until the cooking

process is complete.

Keep in mind that induction may decrease the amount of

time required to preheat a cooking utensil.

Keep Warm Feature

The Warm feature may be used with any of the Cooking

Zones.

To Turn the Keep Warm Feature ON:

1. Select the zone you want to set to warm. If the zone is

off, turn it on, otherwise you can touch either the or

key on the zone you want to set to warm. The most

recently used zone is one that will be placed into warm.

2. Touch the key pad located in the main control area.

The Cooking Zone display will show “L” (Low heat) indicating

that the Cooking Zone is properly set to Keep Warm.

Minute Timer Feature

The Minute Timer feature may be useful in the kitchen if a

recipe calls for keeping track of time. This feature will keep

track of time from 1 to 99 minutes. The display located to

the left of the Timer UP/DOWN arrow key pads will begin

to count down minutes once set.

To Set the Minute Timer:

1. Set the cooktop timer to the desired time by touching

the listed next to the word “TIMER”. Touching and

releasing the or the key pads will increase or

decrease the Minute Timer setting by 1 minute with each

key press (up to 99 minutes). You may also hold the

or key to slew the time to your designated time.

2. Once the Timer displays the desired amount of time,

release the or key pads. The timer will display the

time remaining in minutes within the countdown process.

During the last 60 seconds, the timer will countdown in

seconds.

3. Once the Minute Timer reaches 00 a long beep will sound

every 5 seconds until and key pads are touched

at the same time and the timer display will ﬂ ash “00”

indicating that the time is up.

To Cancel the Minute Timer:

1. Touch the and key pads at the same time or

touch and hold either the or key pad and scroll

to 00.

2. If cancelling the Minute Timer using the scrolling method,

once the Main Control display reaches 00, release the

Arrow key pad.

3. The set time will disappear from the LED indicating that

the Minute Timer is no longer active.

Locking the Controls Feature

The Induction Cooktop may be locked in order to prevent

the cooktop from accidentally being turned ON.

To Turn ON the Controls Lock Feature:

1. The Cooktop Lock will not activate until the cooktop is

OFF. If the cooktop power is not OFF, touch and hold

the key pad until a beep sounds (about 1 second).

The Power LED located above the key pad will turn

OFF.

2. Touch the key pad until a beep sounds (about 3

seconds). The Lock LED above the key pad will turn

ON indicating the cooktop is locked. This will keep any

Cooking Zone or Cooktop functions from being accidentally

turned ON.

To Turn OFF the Controls Lock Feature:

1. Touch the key pad until a beep sounds (about 3

seconds). The Lock LED above the key pad will turn

OFF indicating the cooktop is unlocked. The Cooking

Zones or any of the other Cooktop functions may now

be used.

2. If the cooktop is needed you must touch and hold the

key pad until a beep sounds (about 1 second). The

Power LED located above the key pad will turn ON.

You may now activate any of the Cooking Zones.

Power Sharing

In order to give you more ﬂ exibility, your induction cooktop

is equipped with more cooking zones than the number of

induction generators. Each of those generators is assigned

to power a speciﬁ c cooking zone (see Figure on next page).

One or two cooking zones are assigned to each generator.

To be able to give you access to the highest power ratings,

the generator will focus its power onto only one cooking

zone. If you use more than one cooking zone at high power

on the same generator, the generator will need to share

its power to both cooking zones, thus lowering the power

level of one of the cooking zones.

When you are sharing power (cooking in both zones), the

last zone set will cook at the power setting you selected.

The other zone will experience a slight decrease from its

power setting if both zones are set high enough.

Depending on the size of your cooktop, 2 or 3 sections are

available:

• The 30” cooktop is equipped with 4 cooking zones within

2 sections.

• The 36” cooktop is equipped with ﬁ ve cooking zones within

3 sections. Note that on the 36” cooktop the right cooking

zone has its own section and will not share its power.

SETTING COOKTOP CONTROLS

Power Sharing (continued)

To get the highest power output from your cooking zones,

cook with only one cookware per heating section. If you

need to use most of your cooking zones at once, start your

cooking process on only one cooking zone within the heating

section and then add your second cookware on the second

cooking zone when the ﬁ rst one has already reached its

cooking temperature.

Remember to select the power setting last for the cooking

zone you want to maintain at full power or set the altered

power to where you want it.

Operational Noises

The electronics generating the induction ﬁ elds are pretty

much noiseless but they do produce heat at high power

level. A soft-sounding cooling fan activates when the unit is

running multiple cooking zones at once or when a cooking

zone is set at very high power settings.

The buzzing sound you could hear from your cooktop is

not coming from the electronics but from the cookware

you are using. Here are some causes of this noise:

• Most induction-ready cookware are made of several

layers of materials. An encapsulated steel layer is usually

used to harness the induction ﬁ eld and transform it into

heat, which is then transferred to the other materials by

radiant energy. The induction ﬁ eld will cause the steel

layer to vibrate against the other materials in which it is

encapsulated. This is the most common cause of noise

from the induction process. This buzzing only happens

at the higher power level settings. Note that high quality

cookware manufacturers weld this steel layer in place

which lowers or cancel this noise.

• Light weight cookware may also vibrate. We recommend

using heavy weight quality cookware.

• Cookware with warped bottoms can vibrate on the

ceramic glass surface at high power settings.

• The power output of your induction

cooktop is capable of warping an empty pan. Never use

the higher power settings on an empty pan. Even the

highest quality cookware is vulnerable to warping.

• Riveted handles on cookware can also cause buzzing

sounds from the vibrations.

• Solid cast iron and enamelware cookware should not

emit any noise. Top quality cookware made of several

layers should also be relatively quiet.

SETTING COOKTOP CONTROLS

3 Induction Generators

Cooking Zones

2 Induction Generators

30” model

36” model

CARE & CLEANING

Cleaning Various Parts of Your Cooktop

Before cleaning any part of the cooktop, be sure all controls are turned OFF and the cooktop is COOL. REMOVE SPILLOVERS

AND HEAVY SOILING AS SOON AS POSSIBLE. REGULAR CLEANINGS NOW WILL REDUCE THE DIFFICULTY AND EXTENT

OF A MAJOR CLEANING LATER.

Surfaces How to Clean

Stainless Steel

Decorative Trim Cooktop, Control

Knobs, Control Panel

Wipe the control panel clean after each use. Before cleaning the control

panel, turn all controls to OFF. Clean using hot, soapy water and a cloth. Do not

use cleaners with high concentrations of chlorides or chlorines. Do not use

harsh scrubbing cleaners. Be sure to squeeze excess water from the cloth before

wiping the panel; especially when wiping around the controls. Excess water in or

around the controls may cause damage to the appliance. Only use kitchen cleaners

that are especially made for cleaning stainless steel. Always be sure to rinse the

cleaners from the surface as bluish stains may occur during heating that cannot be

removed.

Ceramic Glass

Cooktop

See Ceramic Glass Cooktop in this Owner’s Guide.

Ceramic Glass Cooktop Cleaning &

Maintenance

Consistent and proper cleaning is

essential to maintaining your Ceramic

glass cooktop.

Prior to using your cooktop for the ﬁ rst time, apply

a ceramic cooktop cleaning cream (available in most

hardware, grocery and department stores) to the ceramic

surface. Clean and buff with a clean paper towel. This will

make cleaning easier when soiled from cooking. Cooktop

cleaning creams leave a protective ﬁ nish on the glass to

help prevent scratches and abrasions.

Sliding aluminum or copper clad bottom pans on the

cooktop can cause metal markings on the cooktop

surface. These marks should be removed immediately

after the cooktop has cooled using the cooktop cleaning

cream. Metal marks can become permanent if not

removed prior to future use.

Cookware (cast iron, metal, ceramic or glass) with rough

bottoms can mark or scratch the cooktop surface. Do

not slide anything metal or glass across the cooktop.

Do not use your cooktop as a cutting board or work

surface in the kitchen. Do not cook foods directly on the

cooktop surface without a pan. Do not drop heavy or

hard objects on the glass cooktop, or they may crack it.

CARE & CLEANING

Cleaning Recommendations for the

Ceramic Glass Cooktop

For light to moderate soil:

Apply a few drops of cooktop cleaning cream directly

to the cooktop. Use a clean paper towel to clean the

entire cooktop surface. Make sure the cooktop is cleaned

thoroughly, leaving no residue. Do not use the towel you

use to clean the cooktop for any other purpose.

For heavy, burned on soil:

First, clean the surface as described above. Then, if soils

remain, protect your hand with a potholder and carefully

scrape soils with a metal razor blade scraper, holding

scraper at a 30 degree angle to the surface. Remove

loosened soils with cooktop cleaning cream and buff

surface clean.

Do not use the following on the ceramic glass

cooktop:

• Do not use abrasive cleaners and scouring pads,

such as metal and some nylon pads. They may

scratch the cooktop, making it more difﬁ cult to

clean.

• Do not use harsh cleaners, such as chlorine

bleach, ammonia or oven cleaners, as they may

etch or discolor the cooktop.

• Do not use dirty sponges, cloths or paper

towels, as they can leave soil or lint on the

cooktop which can burn and cause Special

Caution for Aluminum Foil and Aluminum

Cooking Utensils

WARNING

DO NOT use a cooktop cleaner on a hot cooktop.

The fumes can be hazardous to your health, and can

chemically damage the ceramic glass surface.

CAUTION

Before cleaning the cooktop, be sure the controls are

turned to OFF and the cooktop is COOL.

• Aluminum foil

Use of aluminum foil will damage the cooktop. Do not

use under any circumstances.

• Aluminum utensils

Since the melting point of aluminum is much lower

than that of other metals, care must be taken when

aluminum pots or pans are used. Pans that boil dry

may permanently damage cooktop by breaking, fusing

to, or marking it.

Care and Cleaning of Stainless Steel

Some models are equipped with stainless steel exterior

parts. Special care and cleaning are required for

maintaining the appearance of stainless parts. Refer

to the General Care & Cleaning table for detailed

cleaning instructions.

IMPORTANT

Damage to the ceramic glass cooktop may occur if you

use an abrasive type scratch pad. Only use cleaning

products that have been speciﬁ cally designed for

ceramic glass cooktop.

Plastic or foods with a high sugar content:

These types of soils need be removed immediately if

spilled or melted onto the ceramic cooktop surface.

Permanent damage (such as pitting of the cooktop

surface) may occur if not removed immediately. After

turning the surface elements OFF, use a razor blade

scraper or a metal spatula with a mitt and scrape the soil

from the hot surface (as illustrated). Allow the cooktop to

cool, and use the same method for heavy or burned on

soils.

IMPORTANT

Before you call for service, review this list. It may save you time and expense. The list includes common

occurrences that are not the result of defective workmanship or materials in this appliance.

BEFORE YOU CALL (Solutions to Common Problems)

OCCURRENCE POSSIBLE CAUSE/SOLUTION

Entire cooktop does

not operate.

Cooktop controls are locked. Set the cooktop controls to unlock the Cooktop.

Make sure household electrical circuit breaker is ON and that power is properly supplied to the

Cooktop.

Service wiring is not complete. Contact installation agent or dealer.

Electrical power outage. Check house lights to be sure. Call your local electric company for

service.

Cooktop turns OFF

while cooking.

Cooktop internal heat sensor has detected high temperatures inside the appliance. Be sure

the appliance vent holes are not blocked. Refer to the Installation Instructions supplied

with the cooktop for more detailed cooktop installation information.

Fluids spilled or object lying on controls area of cooktop. Clean spills or remove object. Re-power

cooktop.

Cooking Zone does

not heat food (Power

level is ﬂ ashing).

No cookware was placed on the Cooking Zone, or the cookware material type is incorrect for

Induction Cooking.

Cookware bottom not large enough for Cooking Zone.

Cookware is warped or in poor condition.

Cookware is not centered on Cooking Zone.

Cookware resting on cooktop trim or does not rest completely on cooktop surface.

Cooking Zone does

not heat food.

No power to the appliance. Check steps under "Entire cooktop does not operate" in this

checklist.

Incorrect Cooking Zone control setting. Make sure the correct control is ON for the Cooking Zone being

used.

Cooking Zone heats

food too hot or not

hot enough.

Incorrect power level setting. Adjust the power level setting higher or lower and refer to

recipe for guidance and adjust accordingly.

Food does not heat

evenly.

Lightweight or warped pans were used. Be sure to use good quality cookware.

Use only ﬂ at bottom, evenly balanced medium or heavyweight cookware. Heavy and

medium weight pans heat evenly. Because lightweight pans heat unevenly, foods may burn

more easily.

Adjust Cooking Zone power level setting until the proper amount of heat is obtained.

Poor cooking results. Many factors affect cooking results. Adjust the recipe’s recommended power levels or cooking

times.

Cookware is too lightweight or warped. Use heavier quality cookware so foods being

prepared may cook more evenly.

Cooktop Zone Control

displays C or timer

display displays a 2

digits error code.

Induction Cooktop main control has detected a fault or error condition. Try turning electrical

power supply OFF and back ON to cooktop in order to reset Cooktop main controls. Make

sure nothing touch control panel area (utensils, cookware, etc.). If fault recurs, record fault

number and turn power supply to Cooktop OFF. Call service for assistance.

BEFORE YOU CALL (Solutions to Common Problems)

OCCURRENCE POSSIBLE CAUSE/SOLUTION

Cooking Zone LED

continuously ﬂ ashes.

Induction Cooktop pan detection sensors do not see the correct cookware. Test with a

magnet to be sure cookware is made with Induction compatible material.

Cookware has been removed from the Cooking Zone without turning the Cooking Zone OFF.

Place cookware back on to the Cooking Zone or if ﬁ nished cooking turn off the affected

Cooking Zone.

Cookware is not centered over the Cooking Zone properly. Refer to page 8 for correct

cookware placement.

Metal marks on

ceramic cooktop

surface.

Sliding or scraping of metal utensils on cooktop surface. DO NOT slide cookware or cooking

utensils across the cooktop surface. Use the recommended ceramic glass cooktop cleaning

creme to remove the marks. See "Cooktop Cleaning & Maintenance" in the General Care &

Cleaning section.

Scratches or

abrasions on ceramic

cooktop surface.

Coarse particles such as salt or sand between cooktop and cookware or cooking utensils

can cause scratches. Be sure cooktop surface and bottoms of utensils are clean before

placing on cooktop. Small scratches do not affect cooking and will become less visible with

time.

Cleaning materials not recommended for ceramic-glass cooktop have been used. See

"Cooktop Cleaning & Maintenance" in the General Care & Cleaning section.

Cookware with rough bottoms was used. Use smooth, ﬂ at-bottomed cookware ONLY.

Brown streaks or

specks on ceramic

cooktop surface.

Boil overs are cooked onto cooktop surface. Use a razor blade scraper to remove soil. See

"Cooktop Cleaning & Maintenance" in the General Care & Cleaning section.

Areas of discoloration

with metallic sheen

on ceramic cooktop

surface.

Mineral deposits from food and/or water. Remove using a ceramic-glass cooktop cleaning

creme. Remember to use cookware with clean, dry bottoms. For more information See

"Cooktop Cleaning and Maintenance" in the General Care & Cleaning section.

Cooktop makes

buzzing noise.

Cookware is damaged. Please see pages 7 & 8 of this manual. Also see “Operational noise”

section on page 12.

Fig. 1

Fig. 2

Error Codes Display Message

The error code will display in the zone that has the error.

The error will ﬂ ash through the code C, X, X (Example Fig. 1)

where the X is the number of the code. If the zone has been

on and the zone is hot enough to display H (Example Fig.

2) and you have an error then you will see C, X, X, H.

NOTES

MAJOR APPLIANCE WARRANTY

This warranty does not cover the following:

1 Products with original serial numbers that have been removed, altered or cannot be readily

determined.

2 Product that has been transferred from its original owner to another party or removed outside the

USA or Canada.

3 Rust on the interior or exterior of the unit.

4 Products purchased "as-is" are not covered by this warranty.

5 Food loss due to any refrigerator or freezer failures.

6 Products used in a commercial setting.

7 Service calls which do not involve malfunction or defects in materials or workmanship, or for

appliances not in ordinary household use or used other than in accordance with the provided

instructions.

8 Service calls to correct the installation of your appliance or to instruct you how to use your appliance.

9 Expenses for making the appliance accessible for servicing, such as removal of trim, cupboards,

shelves, etc., which are not a part of the appliance when it is shipped from the factory.

10 Service calls to repair or replace appliance light bulbs, air ﬁ lters, water ﬁ lters, other consumable, or

knobs, handles, or other cosmetic parts.

11 Surcharges including, but not limited to, any after hour, weekend, or holiday service calls, tolls, ferry

trip charges, or mileage expense for service calls to remote areas, including the state of Alaska.

12 Damages to the ﬁ nish of appliance or home incurred during installation, including but not limited to

ﬂ oors, cabinets, walls, etc.

13 Damages caused by: services performed by unauthorized service companies; use of parts other than

genuine Electrolux parts or parts obtained from persons other than authorized service companies; or

external causes such as abuse, misuse, inadequate power supply, accidents, ﬁ res, or acts of God.

DISCLAIMER OF IMPLIES WARRANTIES; LIMITATION OF REMEDIES

Customer’s sole and exclusive remedy under this limited warranty shall be product repair or

replacement as provided herein. Claims based on implied warranties, including warranties of

merchantability or fitness for particular purpose, are limited to one year or the shortest period

allowed by law, but not less than one year. Electrolux shall not be liable for consequential or

incidental damages such as property damage and incidental expenses resulting from any breach

of this written limited warranty or any implied warranty. Some states and provinces do not allow

the exclusion or limitation of incidental or consequential damages, or limitations on the duration of

implied warranties, so these limitations or exclusions may not imply to you. This written warranty

gives you specific legal rights. You may also have other rights that vary from state to state.

Keep your receipt, delivery slip, or some other appropriate payment record to establish the warranty period

should service be required. If service is performed, it is in your best interest to obtain and keep all receipts.

Service under this warranty must be obtained contacting Electrolux at the addresses or phone numbers

below.

Exclusions

If You

Need

Service

USA

1.800.944.9044

Electrolux Home Products, Inc.,

10200 David Taylor Drive

Charlotte, NC 28262

Canada

1.800.265.8352

Electrolux Canada Corp.

5855 Terry Fox Way

Mississauga, Ontario, Canada

L5V 3E4

Your appliance is covered by a one year limited warranty. For one year from your original date of purchase, Electrolux

will pay all costs for repairing or replacing any parts of this appliance that prove to be defective in materials or

workmanship when such appliance is installed, used and maintained in accordance with the provided instructions.

This warranty only applies in the USA and Canada. In the USA, your appliance is warranted by Electrolux Major

Appliances North America, a division of Electrolux Home Products, Inc. In Canada, your appliance is warranted by

Electrolux Canada Corp. Electrolux authorizes no person to change or add to any obligations under this warranty.

Obligations for service and parts under this warranty must be performed by Electrolux or an authorized service

company. Product features or speciﬁ cations as described or illustrated are subject to change without notice.

TABLE DES MATIÈRES

www.frigidaire.com États-Unis 1 800 944-9044 www.frigidaire.ca Canada 1 800 265-8352

Tout à propos de

l'utilisation

et l'entretien

de votre table de cuisson

Bienvenue & félicitations ........................................2

Mesures de sécurité importantes ............................3

Caractéristiques de la table de cuisson ....................5

Instructions rapides ...............................................6

Avant d’utiliser la table de cuisson ..........................7

318205604 (Mars 2015) Rev. C

Réglage des contrôles de la table de cuisson ...........9

Entretien & nettoyage ..........................................13

Avant d’appeler le service ...................................15

Notes .................................................................17

Garantie des appareils électroménagers ................18

BIENVENUE & FÉLICITATIONS



NOTE

Apposez ici votre reçu pour toute référence future.

Inscrivez ci-dessous les numéros de modèle et

de série de votre appareil.

Numéro de modèle:

Numéro de série:

Date d’achat:

Félicitations, vous venez d’acheter un nouvel appareil! Chez

Electrolux Home Products, nous sommes très ﬁ ers

de nos produits et nous nous engageons à vous fournir

le meilleur service possible. Vous satisfaire constitue la

première de nos priorités.

Nous savons que votre nouvel appareil vous plaira et nous

vous remercions d’avoir choisi nos produits. Nous espérons

que vous nous ferez conﬁ ance pour vos futurs achats.

LISEZ ATTENTIVEMENT CES INSTRUCTIONS ET

CONSERVEZ-LES PRÉCIEUSEMENT.

Ce manuel donne des instructions générales pour votre

appareil et des renseignements s’appliquant à plusieurs

modèles. Votre appareil peut ne pas avoir toutes les

caractéristiques décrites. Les ﬁ gures montrées dans ce

manuel sont représentatives et peuvent ne pas illustrer

exactement les caractéristiques de votre appareil. Les

instructions données dans ce guide ne couvrent pas toutes

les conditions et situations possibles. Faites preuve de bon

sens et de prudence lors de l’installation, de l’emploi et de

l’entretien de tout appareil ménager.

Enregistrement de l’appareil

Emplacement de

la plaque de série

Emplacement

de la plaque

de série

Enregistrer l’appareil

La CARTE D’ENREGISTREMENT

doit être remplie en entier et

retournée à

Electrolux Home Products.

Imprimé en Chine

La page charge ...

Frigidaire FGIC3067MB Manuel utilisateur

Marque: Frigidaire

Modèle: FGIC3067MB

Catégorie: Plaques de cuisson

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Frigidaire FGIC3067MB User manual

Frigidaire FGIC3067MB Manuel utilisateur

Ce manuel convient également à

Frigidaire FGIC3067MB Manuel utilisateur

dans d''autres langues

Autres documents