Targus ACP45EU Le manuel du propriétaire

USER GUIDE

Universal Laptop

Docking Station

Visit our website at www.targus.com

Features and specifications are subject to change without notice.

ACP45EU / 410-0391-003C

Table of ConTenTs

2

Targus Universal Laptop Docking Station ............................ 3

Targus Universelle Laptop-Dockingstation ........................ 21

Targus Docking Station Universal Para Portátil ................. 39

Targus Station D’accueil Universelle Pour Ordinateur Portable

............................................................................................ 57

Targus Universal Laptop Docking Station .......................... 75

Targus Universeel Docking Station Voor Laptops .............. 93

Targus Universal Laptop Docking Station ........................ 111

DE - Deutsch

ES - Español

GB - English

FR - Français

IT - Italiano

NL - Nederlands

PT - Português

3

TARGUS

UNIVERSAL LAPTOP

DOCKING STATION

Introduction

Congratulations on your purchase of the Targus Universal

Laptop Docking Station. This portable expansion module

allows you to connect through a single USB connection up

to 4 USB devices, a network (Ethernet/LAN) connection,

speakers and microphone, PS/2 mouse and keyboard,

and a serial and parallel device. Also, the lock slot and

universal lock support provided helps you secure your

docking station to your desktop.

The docking station also features Targus Always On

technology, Targus USB Power Port providing twice the

USB speciﬁcation for higher power requirement devices,

and USB ports that are widely spaced to acommodate

larger adapters. Targus Always On provides power

to the USB ports even when the laptop is shut-down,

disconnected from the docking station or in hibernate/

stand-by mode. This allows USB devices that charge via

the USB port to keep charging under any circumstance.

Targus Universal Laptop Docking Station

4

Features

Heat dissipation by natural

convection:

Comfort

The docking station provides the

following ports:

Place the back edge of your laptop on the rubber pads of

the Docking Station. Most laptops dissipate heat through

the bottom and the more air that’s allowed to ﬂow under

the bottom, the better chance that heat will dissipate by

natural convection.

The raised platform also provides a more comfortable

position for the hands.

• Two PS/2 ports

• IEEE 1284 DB25 Connector parallel (USB emulated)

• Two 3.5 mm Audio: (1) stereo out and (1) microphone

in

• RS232 serial (USB emulated)

• One S/PDIF Digital Audio Output (not supported in

Windows 2000)

• RJ-45 Ethernet 10/100

• Four USB 2.0 Ports:

- Two High-Speed USB 2.0 ports

- Two High-Speed USB 2.0 Always-On ports with extra

power

5

Targus Universal Laptop Docking Station

Package Contents

In addition to this user guide, the package contains:

• Targus Universal Laptop Docking Station

• High-speed USB 2.0 upstream cable

• Driver software CD

• AC power adapter

System Requirements

Hardware

• PC with an Intel

®

Pentium

®

processor or equivalent

• CD-ROM drive

• USB version 2.0 port

• AC power source (AC adapter required)

NOTE: WhEN cONNEcTEd TO a USB vErSiON 1.1 pOrT ON

yOUr cOmpUTEr, ThE dOckiNg STaTiON’S pErfOrmaNcE

lEvEl Will BE lESS ThaN OpTimal. fOr BEST rESUlTS,

cONNEcT iT TO a USB vErSiON 2.0 pOrT.

Operating System

• Windows

®

2000 Service Pack 4 or

• Windows

®

XP Service Pack 3 or

• Windows Vista

®

Service Pack 1

Targus Universal Laptop Docking Station

6

Installing the Device

and Drivers

WarNiNg: yOU mUST iNSTall ThE SOfTWarE BEfOrE

cONNEcTiNg ThE dOckiNg STaTiON TO yOUr cOmpUTEr.

OThErWiSE, ThE dOckiNg STaTiON Will NOT WOrk prOpErly.

To use the Targus docking station, you must ﬁrst install

the driver onto your computer.

After installing your software, connect the docking station

to your computer and Windows plug-and-play will install

the hardware drivers for each port.

Installing the Docking Station

Driver

Installing the docking station driver enables your

operating system to recognize it and its ports once it’s

connected.

1 Turn on your computer.

2 Insert the driver software CD into your computer’s

CD-ROM drive.

If setup does not begin automatically, click Start, Run,

and enter D:\ACP45_setup.exe (where D: is the path of

your CD-ROM drive) and then click OK.

7

Targus Universal Laptop Docking Station

3 The Installation Wizard window of the docking station

will pop up. Click Next to proceed.

4 The

Information window will pop up. Click Next to

proceed. In order to install the driver ﬁles properly,

you must restart your system before plugging in

the docking station.

Targus Universal Laptop Docking Station

8

5 Choose Yes, I want to restart my computer now.

Click Finish and restart your computer when

prompted.

Connecting the Docking

Station to Your Computer

After installing the docking station software, you are

ready to connect the docking station to your computer. To

do this:

1 Connect the supplied AC power adapter to the AC

power jack on the docking station.

2 Connect one end of the USB cable to the docking

station and the other end into an available USB 2.0

port on your computer.

WarNiNg: ThE dOckiNg STaTiON Will NOT fUNcTiON

prOpErly WiThOUT ThE ac adapTEr plUggEd iNTO aN ac

OUTlET.

dO NOT cONNEcT aNy dEvicES TO ThE dOckiNg STaTiON

UNTil ThE iNSTallaTiON iS cOmplETEd.

9

Targus Universal Laptop Docking Station

Installing the Default Device

Drivers

Once you connect the docking station to your computer,

the default drivers begin installing for each of the ports

automatically.

NOTE: plEaSE ENSUrE yOU havE ThE laTEST SErvicE packS

iNSTallEd.

Some hardware devices may prompt you to install the

drivers.

To install the drivers:

1 Select Install the software automatically

(Recommended) and click Next.

The Found New Hardware Wizard program begins

installing the hardware drivers.

The Completing the Found New Hardware Wizard

screen appears.

2 Click Finish and repeat as needed for each device.

3 Restart your computer.

LED Status Indicator Lights

Once all device drivers are installed, the USB LED status

indicator lights on the back of the docking station glow

when you connect devices to the docking station.

• Green Tx light illuminates when connected to a

network and the yellow Rx light ﬂashes when data is

transmitting to or from the network.

NOTE: ThE dOckiNg STaTiON SUppOrTS hOT SWappiNg Of

ThE NETWOrk caBlE.

Targus Universal Laptop Docking Station

10

Docking station ports

Docking station left-side view

Docking station right-side view

Laptop Support Pad

Serial S/PDIF Network High-Speed USB

2.0 Always-On

with Extra Power

PS/2 Parallel Audio In Audio Out

High-Speed

USB 2.0 Port

Cable

Lock Slot

“Easy Access”

High-Speed

USB 2.0 Port

Targus

DEFCON CL,

PA410E (not

included)

Cable

Lock Slot

USB to PC

Connection

AC Adapter

11

Targus Universal Laptop Docking Station

Connecting New

Devices

Connecting a Serial Mouse /

Keyboard

Connecting a PS/2 Mouse /

Keyboard

Connecting and Conguring a

Serial Modem

To avoid possible damage when connecting a new

device, do not force the cable connector into the port on

the docking station. If the cable connector does not attach

smoothly, turn the connector over and try attaching it

again.

To connect a serial mouse or keyboard, attach the cable

connector to the serial port on the docking station.

To connect a PS/2 mouse or keyboard, attach the cable

connector to the PS/2 port on the docking station.

To connect a serial modem:

1 Attach the cable connector to the serial port on the

docking station.

2 Install the modem software driver according to the

instructions that come with the device.

3 When prompted to select the port, choose the Serial

USB (COMx), where x is the COM port number

assigned by your operating system.

Targus Universal Laptop Docking Station

12

Connecting a Parallel Printer

Connecting a PDA

Connecting to a Local Area

Network

To connect a parallel printer:

1 Attach the cable connector to the parallel port on the

docking station.

2 Go to Start button of your Window OS, and click on

Printers and Faxes. Add your printer driver by

following the instructions of the

Add Printer Wizard.

1 Attach the cable connector to the serial port on the

docking station.

2 Verify that the COM port setting, in either your

HotSync

®

or ActiveSync

®

software, matches the setting

on the docking station.

To verify the COM port setting on the docking station,

refer to “Verifying Devices are Installed”.

To verify the COM port setting on your PDA, refer to

the documentation that came with it.

To connect an Ethernet cable with an RJ-45 connector,

attach the cable connector to the Ethernet/network port

on the docking station. Additional procedures to connect

to an actual network depend on the type of network you

are using. Contact your network administrator for detailed

instructions.

13

Targus Universal Laptop Docking Station

Connecting a USB Device

Connecting and Conguring an

Audio Device

To connect a USB device, plug it into a USB port on the

docking station and follow the additional instructions

provided with the device.

All four USB ports meet USB High-speed requirements

by providing 480Mbps and 500mA of power. However, the

two USB ports on the right side denoted by this symbol

have two unique features - Always On and High Power.

See “Targus Always On” and “Using USB Devices That

Require More Power” for more details.

The other USB ports (one on the side and the other on

the back next to the Ethernet port) are ports that provide

the standard 500 mA of power.

1 Plug your headphones or speakers into the green

3.5mm

Audio Out port on the docking station.

2 To connect a microphone, plug it into the mono Audio

In port.

3 To enable your headphones or speakers, you must

ﬁrst choose USB PnP Sound Device in the Properties

Settings.

For Windows 2000, click Start, Settings, Control Panel,

and then open the Sounds and Multimedia folder.

Select the Audio tab. Under Sound Playback, change

Preferred Device to USB PnP Sound Device from the

drop down list.

Click Apply, then click OK.

Targus Universal Laptop Docking Station

14

For Windows XP, go to the Control Panel and choose

Sound and Audio. Select the Audio tab. Under Sound

Playback, change Preferred Device to USB PnP Sound

Device from the drop down list.

Click Apply, then click OK.

For Windows Vista, go to the Control Panel and choose

Hardware and Sound. Select Sound. Under the

Playback tab, select Digital Output of the USB PnP

Sound Device.

Click Set Default.

4 Make sure the volume is not set to MUTE.

NOTE: aUdiO dEvicES Will NOT WOrk SimUlTaNEOUSly ON

ThE pOrT STaTiON aNd ThE hOST cOmpUTEr.

caUTiON: all aUdiO Or mUlTimEdia applicaTiONS mUST BE

TErmiNaTEd BEfOrE SWiTchiNg BETWEEN ThE pOrT STaTiON

aUdiO OUTpUT aNd ThE hOST cOmpUTEr aUdiO OUTpUT.

15

Targus Universal Laptop Docking Station

Installing and Conguring a

S/PDIF (Sony/ Philips Digital

Interface) Device

1 In order to enable S/PDIF, you have to turn it on.

This can be done by opening the USB 3D Sound

Conﬁguration applet located in your system tray (click

on the USB icon to open up the Conﬁguration Screen).

2 Click on the button next to the S/PDIF Output text to

enable S/PDIF.

3 Set the Audio Output from the Tray.

Targus Universal Laptop Docking Station

16

4 Plug your optical cable (not included) into the

S/PDIF-Out port of docking station on one end, and

the S/PDIF-In port of Digital Decoder or Speaker on

the other end.

5 Connect your Digital Decoder or Speaker to the Home

Theater System.

When your computer is in suspend mode, the docking

station also enters suspend mode to avoid power

consumption. When your computer wakes up, the docking

station wakes up automatically.

Global Suspend Mode

Universal Docking Station

Digital Decoder

A/V Receiver

Optical Cable (Not included)

Home Theatre

ZOOM IN

17

Targus Universal Laptop Docking Station

The two USB ports that provide up to 1 Amp of power

will continue providing power even when the laptop is

powered down or disconnected from the docking station.

This allows you to charge any USB device you connect to

these ports without powering your laptop.

Targus Always On

Some devices, which use large amounts of power, such

as printers and optical drives, should be plugged into the

High Power USB Ports. These ports will provide up to

1000 mA of power - double the power of a standard USB

ports.

Using USB Devices

That Require More

Power

Some devices may halt temporarily when a high data

transfer is occurring. For example, your mouse may

respond slowly while a graphic print job is printing or

while you are experiencing heavy network trafﬁc.

We recommend the following guidelines:

• Do not transfer data to or from multiple high-speed

devices, such as a digital camera or scanner, at the

same time.

• If speed degradation does occur, close other programs

that use a USB device to improve device performance.

Product Limitations

Targus Universal Laptop Docking Station

18

• Make sure that the device is fully inserted into the

correct port on the docking station.

• Plug the device into a different port on the docking

station. If it still doesn’t work, test the device by

connecting it directly to your computer.

• Verify that you ran the Setup or Install program for the

device.

• Make sure that the device appears in Device Manager.

For more information refer to “Verifying Devices are

Installed”.

• Disconnect all devices from the docking station and

reconnect them, one at a time. Check that each device

works before plugging in the next one.

• Each USB port is equipped with over-current

protection. Should a USB device draw more current

than the USB port can supply, the port will shut down.

To re-enable the port, unplug the device and go to

Device Manager or to the message in the system

tray and choose the

Reset option. You can then

plug the device back into the USB port. If a shut down

reoccurs, check the power requirements of the device.

Troubleshooting

Device Not Working

19

Targus Universal Laptop Docking Station

Verifying Devices are Installed

You can view the devices installed on the docking station

from the Device Manager window in System Properties.

Right-click My Computer, Properties, then click the

Hardware tab, and then the Device Manager button.

From the Device Manager window, expand the following:

• Human Interface Devices - displays keyboards and

pointing devices: mice, trackballs, and joysticks

• Keyboards — displays PS/2 keyboards

• Mice and Other Pointing Devices — displays PS/2

mouse

• Network Adapters — displays ASIX AX88772A USB

2.0 fast Ethernet Adapter

• Ports (COM & LPT) — Proliﬁc USB-to-Serial Comm

Port (COM X)

• S

ound, Video and Game Controllers — displays

USB PnP Sound Device

• U

niversal Serial Bus controllers — displays the other

devices installed for the docking station and generic

hub

Targus Universal Laptop Docking Station

20

Palm and HotSync are registered trademarks of Palm, Inc. Microsoft, Windows, Windows

Vista and ActiveSync are either registered trademarks or trademarks of Microsoft Corporation

in the United States and/or other countries. All trademarks and registered trademarks are

(UK) Ltd.

If the error message “Connection Not Established”

appears on your PDA, check that the COM port setting in

either your HotSync or ActiveSync software matches the

setting on the docking station. See “Verifying Devices are

Installed” to verify the COM port setting on the docking

station.

Some older versions of the Palm

®

Desktop software are

not compatible with the USB to Serial conversion. Please

contact your PDA vendor for software updates.

Error Message on Your PDA

When attaching a modem to the serial (RS232) port,

verify that the port assigned to your modem is Serial USB

(COMx), where x is the number of the COM port.

If the operating system does not detect automatically that

your modem is assigned to Serial USB (COMx), run the

Hardware Wizard again and choose Select from the list

instead of Autodetect. Then, select use Proliﬁc Device

from Page as the COM port.

Verifying a Serial Modem

Connection

La page est en cours de chargement...

Targus ACP45EU Le manuel du propriétaire

Ce manuel convient également à

Targus ACP45EU Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents