Maytag MAV2757AWW Le manuel du propriétaire

Catégorie
Machines à laver
Taper
Le manuel du propriétaire
MAV-1
Use& CoreGuide
Table of Contents
Important Safety Instructions 1-2 Special Features ........ 12-13
Operating Tips ........... 3-4
Care & Cleaning ........... 13
Using the Controls
3 Speed Select Models ....... 5-6
4 Speed Select Models ....... 7-8
Electronic Control Models ...... 9-1 1
Troubleshooting ........... 14
Service & Warranty ........ 15
Guide d'utilisation
et d'entretien .............. 16
Guia de uso y cuidado ..... 34
Form No. Y81903 A Part No. 2206671 www.maytag.com Litho U.S.A. _2006 Maytag Appliances Sales Co.
ImportnntSnfet¥Instructions
What You Need to Know About
Safety Instructions
Warning and Important Safety Instructions appearing in
this guide are not meant to cover all possible
conditions and situations that may occur. Common
sense, caution and care must be exercised when
installing, maintaining or operating appliance.
Always contact the manufacturer about problems or
conditions you do not understand.
Recognize Safety Symbols, Words,
Labels
ImportnntSnfet¥Instructions
1. Read all instructions before using the appliance,
2, As with any equipment using electricity and having
moving parts, there are potential hazards, To use this 7.
appliance safely, the operator should become familiar
with the instructions for operation of the appliance 8,
and always exercise care when using it.
3, Do not install or store this appliance where it will be
exposed to the weather.
4, Install and level washer on a floor that can support
the weight.
5. This appliance must be properly grounded. Never
plug the appliance cord into a receptacle which is not
grounded adequately and in accordance with local
and national codes. See installation instructions for
grounding this appliance.
6, To avoid the possibility of fire or explosion:
a. De not wash items that have been previously
cleaned in, washed in, soaked in, or spotted with
gasoline, dry-cleaning solvents, other flammable or
explosive substances as they give off vapors that
could ignite or explode. Hand wash and line dry
any items containing these substances,
Any material on which you have used a cleaning
solvent, or which is saturated with flammable
liquids or solids, should not be placed in the
washer until all traces of these liquids or solids
and their fumes have been removed.
b,
C.
These items include acetone, denatured alcohol,
gasoline, kerosene, some liquid household
cleaners, some spot removers, turpentine, waxes
and wax removers.
De not add gasoline, dry-cleaning solvents, or
other flammable or explosive substances to the
wash water. These substances give off vapors that
could ignite or explode.
Under certain conditions, hydrogen gas may be
produced in a hot water system that has not been
used for two weeks or more. HYDROGEN GAS IS
EXPLOSIVE. If the hot water system has not been
used for such a period, before using a washing
machine or combination washer-dryer, turn on all
hot water faucets and let the water flow from each
for several minutes, This will release any
9,
10,
11,
12,
13.
14.
15.
16.
17.
18.
19.
accumulated hydrogen gas. As the gas is
flammable, do not smoke or use an open flame
during this time.
d. De not wash or dry items that are soiled with
vegetable or cooking oil. These items may contain
some oil after laundering. Due to the remaining oil,
the fabric may smoke or catch fire by itself.
De not reach into the appliance if the tub or agitator
is moving.
Do not allow children or pets to play on, in, or in
front of the appliance. Close supervision is necessary
when the appliance is used near children and pets.
Do not tamper with controls.
De not repair or replace any part of the appliance or
attempt any servicing unless specifically
recommended in published user-repair instructions
that you understand and have the skills to carry out.
Unplug power supply cord before attempting to
service your washer. Service is to be done only by
qualified service personnel,
The agitator should not be removed. If the agitator is
removed, it must be replaced by pushing down
completely and the locking screw tightened before
the washer is operated,
Keep all laundry aids such as detergents, bleach, etc.,
out of the reach of children, preferably in a locked
cabinet. Use laundry aids only as directed by the
manufacturer. Observe all warnings on container labels.
Keep the area around and underneath washer free
from the accumulation of combustible materials, such
as lint, paper, rags, gasoline, and all other flammable
vapors and liquids.
Do not use chlorine bleach and ammonia or acids
(such as vinegar or rust remover) in the same wash,
Hazardous fumes can form,
Do not machine wash fiberglass materials. Small
particles can stick to fabrics washed in following
loads and cause skin irritation,
For flame resistant finishes - follow garment
manufacturer's instructions carefully. Improper
laundering could remove the finish,
Before the appliance is removed from service or
discarded, remove the door to the washing compartment.
Inlet hoses are subject to damage and deterioration
over time. Check the hoses periodically for bulges, kinks,
cuts, wear or leaks and replace them every five years,
SAVE THESE INSTRUCTIONS
2
Operutin9Tips
Detergent
Use either liquid or granular laundry detergent. For
best results, he sure detergent is added to the
washer BEFORE the load and he sure the wash
water is above 60 ° F.
Use the correct amount of detergent for the load size,
soil level and water conditions. Use more detergent if
you have hard water and very soiled loads.
If you have soft water or a lightly soiled load, use less
detergent. (See manufacturer's instructions.)
Wipe up any detergent spills on the washer.
Loading
For best results add the detergent to the washtub
before adding the load.
Put dry, unfolded clothes loosely in the tub, up to the
top row of holes for a maximum load.
Do not wrap large items like sheets around the
agitator.
Mix large and small items for best circulation. Wash
bulky items like blankets separately.
When laundering wrinkle-free items or items of
delicate construction, washable woolens or loosely
knit items, never use less than the MEDIUM water
level setting. This will minimize shrinkage, wrinkling
and pulling of seams.
Close lid carefully to avoid slamming.
Operutin9Tips
Additional Tips
During the spin, it is possible for the load to become
unevenly distributed in the tub. If this happens, push
in the control dial, open the lid, redistribute the load,
close the lid and restart the washer. The spin will
resume at the point it was interrupted.
The washer will pause briefly throughout each cycle.
These pauses are normal.
This washer is designed so that it will not agitate or
spin when the lid is open. It will, however, fill with the
lid open so water is available for pretreating stains or
diluting fabric softener.
If you open the lid during a spin cycle, the washer
will stop. When the lid is closed and the washer is
restarted, the washer will continue the cycle at the
point it was interrupted.
Usin9theControls- 3SpeedSelectModels
Select Water Level
Determine the selected setting based on clothes load
size. Selection should provide sufficient water to permit
clothes to circulate freely during agitation.
It may become necessary, due to bulky fabrics, to
adjust the water level after agitation begins. To adjust
the water level, turn the control to reset and then back
to the desired setting.
Mini 1//4 Full
Small 1//4- 1/3
Medium 1/3- 1/2
Large 1/2 - 2/3
Super 3//4- Full
I Note: Items must circulate for best results.
freely
Select Wash/Rinse Temperature
Your washer gives you a choice of hot, warm or cold
water for washing and cold or warm water (select
models) for rinsing. Use the chart below as a guide.
White and heavily soiled, color-fast
Hot/Cold
items.
Warm/Warm Moderately soiled, colored items.
(select models)
Warm/Cold Moderately soiled, colored items;
most wrinkle-free items.
Cold/Cold Brightly colored, lightly soiled
items; washable woolens.
Note: In wash water temperatures below 60° E
detergents do not dissolve well or clean well. Care
labels define cold water as up to 85° E
Water Level Extra Rinse
Medium
Small _ _
Mini
Stainless Steel Tub SuperSi
,\
Automatic Temperature Control (A.T.C.)
(select models) provides the optimal wash water
temperatures for cleaning. To save energy, the
Automatic Temperature Control will regulate wash
water temperatures by mixing hot and cold water to
reach the proper water temperature.
ATC Hot/Cold,
ATC Warm/Cold
ATC WamdWann
(select models)
ATC Cold/Cold
These settings feature Automatic
Temperature Control:
Saves energy by adding cold water
to the hot water from your water
heater. Provides optimum cleaning
at lower temperatures.
May add hot water to the incoming
cold water as the washer fills. This
assures that the water will be warm
enough to properly activate
detergent.
Control features vary by model.
Wash/Rinse Tem p
Automatic Temperature Con[to
A,T,C
Cold Warm
Ware /f_ 2_' ,,% A,T,C
:_ Cold
Cold / '% Warm
_ Cold
Hot
cq_
Signal
Capacity / Quiet Series I00 / 3 Speed Select / 17 Cycles
Spin
On _- Rinse
Delicates
Light
Normal _
Off
Extra
Rinse
Ex. Heavy
Extra Off Heavy. Regular
Rinse i_lormal
off
Rinse
Fxtended Sain
On
off
3ff
Finger
Off Heav_ Fauce[
S_in . Normal
Rinse Light Pull to Start- Push to Stoo
Wrinkle Control
Select Cycle
To select a cycle, push the control dial in (off position)
and turn it to the right (clockwise) until the pointer is at
the soil level needed for the wash load in the Regular,
Wrinkle Control or Delicates cycles.
Regular Cycle
Provides normal agitation and normal spin speeds to
wash cottons and heavily soiled items. For maximum
cleaning, set the dial at Extra Heavy.
Wrinkle Control Cycle
Provides normal agitation and slow spin speed to
protect wrinkle control fabrics.
Delicates Cycle
Provides slow agitation speed and slow spin speed for
delicates and knits.
Select
Options (if desired)
Extra Rinse
When the switch is in the On position, an additional
rinse at the end of the Regular, Wrinkle Control and
Delicates cycles is provided to more completely
remove laundry additives, suds, perfumes, etc.
End of Cycle Signal (select models)
The End of Cycle Signal will sound once the cycle is
completed. The End of Cycle Signal can be canceled by
setting the switch to Off.
Pull Control Dial Out to Start
You may stop the washer at any time by simply
pushing the control dial in. Therefore, it is possible to
obtain a non-agitated soak or to shorten, skip or
repeat any part of a cycle. The control dial must be
pushed in (off position) when you change the setting.
I Note: Do not attempt to turn the control dial
counterclockwise. Damage to the timer will result.
UsingtheControls- 4 SpeedSelectModels
Select Water Level
Determine the selected setting based on clothes load
size. Selection should provide sufficient water to permit
clothes to circulate freely during agitation. On select
models, the Infinite Water Level control allows you to
select a specific setting or anywhere in between.
It may become necessary, due to bulky fabrics, to
adjust the water level after agitation begins. To adjust
the water level, turn the control to reset and then back
to the desired setting.
Mini 1//4Full
Small 1//4- 1/3
Medium 1/3 - 1/2
Large 1/2 - 2/3
Super 3//4 - Full
Note: Items must circulate freely for best results.
Select Wash/Rinse Temperature
Your washer gives you a choice of hot, warm or cold
water for washing and cold or warm water (select
models) for rinsing.
White and heavily soiled, color-fast
Hot/Cold
items.
Warm/Warm Moderately soiled, colored items.
(select models)
Warm/Cold Moderately soiled, colored items;
most wrinkle-free items.
Cold/Cold Brightly colored, lightly soiled
items; washable woolens.
Automatic Temperature Control (A.T.C.) (select
models) provides the optimal wash water temperature
for cleaning. To save energy, this washer will regulate
wash water temperatures by mixing hot and cold water
to reach the proper water temperature.
Infinite Water Level
Medium
Small _*_"'_"0
Mini
Wash/Rinse Tem
AutomatK Temperature Cone
ATC
Cold Warm
Cold
Large
I,, F
i_ Super Warm//'
_' reset Cold
Hot
Cold
Commercial Quality Stainless Steel Tub / SuoerSize
ATC Hot/Cold,
ATC Warm/Cold
ATC WamdWarm
ATC Cold/Cold
These settings feature Automatic
Temperature Control:
Saves energy by adding cold water
to the hot water from your water
heater. Provides optimum cleaning
at lower temperatures.
May add hot water to the incoming
cold water as the washer fills. This
assures that the water will be warm
enough to properly activate detergent.
Select Wash/Spin Speed
Your washer has selectable wash and spin speed
combinations.
Regular
Normal/Fast
Wrinkle Control
Normal/Slow
Delicate
Gentle/Slow
Handwash
Ex. Gentle/Slow
Sturdy fabrics needing maximum
water extraction like jeans, towels
and bedding
Sturdy fabrics needing a slower spin
speed to reduce wrinkling, such as
dress shirts and dress pants
Delicate fabrics needing slower spin
speed because of clothing
construction
Intermittent slow agitation and soak
to gently wash the most delicate items
Note: In wash water temperatures below 60° E
detergents do not dissolve well or clean well.
) Extra Rinse Wash/Spin Speed so_k
Only Off
Off
Extra
W_tinkle Control Delicate Rinse
No_mal/Slo_ GentlelSlow
ATe. On_ _ ;_
Handwash
Warm Reqular _,
Normal/Fast _ _ _ Off
AT.C.
Cold
Cold
Spin
Rinse
Extended Spin
_)n
Off
apaoty IQuiet Series I0014Soeed Select / 18 C),cles Wrinkle Control
Select Cycle
To select a cycle, push the control dial in (off position)
and turn it to the right (clockwise) until the pointer is at
the soil level needed for the wash load.
Important: For optimum fabric care, the appropriate
wash and spin speed for the load type must be
selected using the wash/spin speed knob.
Regular Cycle
This cycle provides up to 16 minutes of agitation.
Select the Regular Wash/Spin Speed setting.
Wrinkle Control
This cycle is designed for sturdy fabrics needing a
slower spin speed to reduce wrinkling, such as dress
shirts and dress pants. Select the Wrinkle Control
Wash/Spin Speed setting.
Delicates Cycle
Delicates is designed for items requiring delicate wash
action. Select the Delicates Wash/Spin Speed
setting.
When washing delicate fabrics labeled hand wash,
select the Handwash Wash/Spin Speed setting. This
setting provides intermittent slow agitation and soak
with a slow spin.
Soak Only (select models)
Provides 4 minutes of agitation, then soak. Avoid
extended soaking - soak for 30 minutes or less.
The control dial must be manually advanced to a spin
setting to spin and drain the water.
Select
Options (if desired)
Extra Rinse
When the knob is in the On position, an additional
rinse at the end of the Regular, Wrinkle Control and
Delicates cycles is provided to more completely
remove laundry additives, suds, perfumes, etc.
End of Cycle Signal (select models)
The end of cycle signal will sound once the cycle is
completed. The end of cycle signal can be canceled by
setting the switch to Off.
Pull Control Dial Out to Start
You may stop the washer at any time by simply
pushing the control dial in. Therefore it is possible to
obtain a non-agitated soak or to shorten, skip or
repeat any part of a cycle. The control dial must be
_ushed in (off position) when you change the setting.
Note: Do not attempt to turn the control dial
counterclockwise. Damage to the timer will result.
I
UsingtheControls- ElectronicControlModels
Getting Started
1. Add detergent and additives to the washer.
2. Load the washer.
3. Close the lid.
4. Select the appropriate cycle and options for the load.
5. Press the Cycle Selector dial.
6. The Fill indicator light will illuminate and the washer
will start to fill.
I
Note: The lid must be completely closed in order I
to operate the washer controls.
I
Infinite Water Level
Medium
Mini _ j queer
rese_
Extra Rinse
Off On
Select Water Level
Determine the selected setting based on clothes load
size. Selection should provide sufficient water to permit
clothes to circulate freely during agitation.
It may become necessary, due to bulky fabrics, to
adjust the water level after agitation begins. To adjust
the water level, turn the Infinite Water Level control to
reset and then back to the desired setting.
Mini 1//4 Full
Small 1//4- 1/3
Medium 1/3- 1/2
Large 1/2 - 2/3
Super 3//4- Full
I Note: Items must circulate for best results.
freely
Commercial Qual{ty Stainless Steel Tub / Supe_Size Cap
HotJCold White and heavily soiled, color-fast
(select models) items.
Warm/Warm Moderately soiled, colored items.
(select models)
Warm/Cold Moderately soiled, colored items;
(select models) most wrinkle-free items.
Cold/Cold Brightly colored, lightly soiled
items; washable woolens.
Automatic Temperature Control (A.T.C.) provides
the optimal wash water temperature for cleaning. To
save energy, this washer will regulate wash water
temperatures by mixing hot and cold water to reach
the proper water temperature.
Select Wash/Rinse Temperature
Your washer gives you a choice of hot, warm or cold
water for washing and cold water or warm water
(select models) for rinsing. Use the chart as a guide.
These settings feature Automatic Temperature Control:
Saves energy by adding cold water
ATC Hot/Cold,
to the hot water from your water
ATC Warm/Cold
ATCWarm/Warm heater. Provides optimum cleaning
(select models) at lower temperatures.
May add hot water to the incoming
cold water as the washer fills. This
ATC Cold/Cold
assures that the water will be warm
enough to properly activate detergent.
Control features vary by model.
Wash/Rinse Temp
Soil Selection
Cold Warm
Cold Cold /ormal _eavy
HOt
_Coid Dght
Fabric Selection
_rir_kle Control
DeIicates
ilaRdwasn
OuickWash
:)1
off
Signal
_zy / Quiet Ser_e_200 / 5 Speed Select / 21 Cycles
Soil Selection
Your washer has selectable soil level settings.
.........................................................................
Light Use for cleaning lightly soiled loads.
Normal Use for cleaning moderately soiled
loads. This setting will be appropriate
for most loads.
Heavy Use for cleaning heavily soiled loads.
Extra Heavy Use for cleaning stained, heavily
soiled sturdy loads.
Fabric Selection
Select the appropriate fabric cycle for the type of load
by turning the cycle selector dial until the indicator
light by the desired fabric selection is illuminated.
Quick Wash
Gentle/Fast
Hand Wash
Ex. Gentle/Slow
Delicates
Gentle/Slow
Wrinkle Control
Medium/Slow
Regular
Medium/Fast
For lightly soiled or wrinkled
garments needed quickly.
Provides intermittent agitation and
soak. For wool, silk, and other
hand-wash-only fabrics.
For sheer fabrics, bras and lingerie
needing slower agitation and spin
speeds because of clothing
construction.
For "wash and wear" and synthetic
fabrics and lightly to normally soiled
garments needing a slower spin
speed to reduce wrinkling.
For most sturdy fabrics including
cottons, linens and normally soiled
garments needing maximum water
extraction.
10
UsingtheControls- ElectronicControlModels
Soak Only [selectmodels)
Provides approximately 33 minutes of alternating
periods of soaking with brief agitation at slow speed.
At the end of the cycle, the Cycle Selector dial must be
manually set to a wash cycle or spin cycle to drain the
washer. Avoid extended soaking.
Spin Only
Provides a spin to remove more water from the load.
Rinse and Spin
Use for loads that need rinsing only or to add rinse-
added fabric softener to a load.
Power Off
To cancel the cycle and turn off the washer, turn the
Cycle Selector dial to Power Off and push the dial in.
F_¢i c _eledi_n
Select Options
Extra Rinse
When the knob is in the On position, an
additional rinse at the end of all cycles
is provided to more completely remove
laundry additives, suds, perfumes, etc.
Extra Rinse
Off On
End of Cycle Signal
The end of cycle signal will sound once the on
cycle is completed. On select models, the
end of cycle signal can be canceled by off
setting the switch to Off.
Signal
Start the Washer
To start the washer, press the cycle selector dial.
Changing a Cycle
If an incorrect cycle has been accidentally
selected:
1. Press the cycle selector dial.
2. Turn the cycle selector dial to the desired cycle.
3. Set the desired options for the cycle.
/4. Press the cycle selector dial. The Wash indicator
lights stop flashing and the new cycle starts.
Canceling a Cycle
To cancel a cycle:
1. Press the cycle selector dial.
2. Turn the cycle selector dial to Power Off and push
the dial in.
To drain the washer:
1. Select the Rinse and Spin or Spin Only cycle.
2. Press the cycle selector dial. The Spin light
illuminates and the washer starts the rinse or spin.
11
SpecialFeatures
Liquid Bleach Dispenser
The dispenser automatically dilutes liquid chlorine
bleach before it reaches your wash load.
To use, follow these steps:
1. Measure liquid chlorine bleach carefully, following
the instructions on the bottle.
2. Pour liquid chlorine bleach into bleach
dispenser before adding the load. Avoid splashing
or over-filling the dispenser.
Notes:
Never pour undiluted liquid chlorine bleach
directly onto the load or into the wash tub. It is a
powerful chemical and can cause fabric damage,
such as tearing or color loss, if not used properly.
If you prefer to use color-safe, non-chlorine
bleach, pour it into the wash tub with your
detergent. Do not pour non-chlorine bleaches into
the bleach dispenser.
Finger Faucet Cselect models)
Provides a flow of water when holding the r_
switch in the On position, f_
Fabric Softener Dispenser
The dispenser automatically releases liquid fabric
softener at the proper time during the cycle.
To use, follow these steps:
1. Pour a measured amount of fabric softener into
the dispenser to fill line only.
2. If fabric softener comes below line, add warm
water.
If it is necessary to clean the dispenser:
1. Pull the dispenser off of the top of the agitator.
2. Soak for one hour in sink or container in hot water
and dishwashing liquid.
3. Hold hands over top and bottom of dispenser and
shake to loosen buildup.
/4. Rinse with clean, hot water.
5. Repeat process if necessary.
6. Replace dispenser on agitator.
Do not use dishwashing liquid
inside the washer. Oversudsing
can occur.
Automatic Lint Filtering System
The Lint Filtering System does not require
cleaning.
Wash and rinse water is filtered and re-filtered
continuously to trap lint shed by most fabrics during
the agitation cycle before it can be redeposited on the
wash load. The engineered hole design on the wash
basket in conjunction with water flow produced by the
agitator, traps lint away from the clothes between the
inner wash basket and the outer tub. Lint is
automatically flushed from the washer during the spin
cycle.
Safety Spin
If for any reason you open the washer lid when the
washer is in a spin or extract period, the operation will
immediately stop. This is for your personal safety. If
your washer does not stop, call your service technician
immediately. When the lid is closed, the operation will
automatically resume.
12
SpecialFeatures
Unbalanced Spin Load
Compensator
Your new washer is designed to handle out-of-balance
loads without shutting down or interrupting the
washing cycle.
For this reason, the cycle will always be completed. If
heavier fabrics in such out-of-balance loads should
ever contain excessive moisture at the completion of
the cycle, redistribute the clothes in the washer and
reset the control dial for the final spin period.
Overload Protector
A built-in protector automatically shuts off the washer
motor in case of an overload. This can occur if:
The load being washed is too heavy.
Too many appliances are plugged into the line
operating your washer.
A low voltage condition exists on the line.
Lid is opened and closed repeatedly.
The overload protector permits the washer to start again
when the motor has cooled to a safe operating temperature.
If the motor stops repeatedly, call your service technician.
Care&Cleaning
.
10.
11.
1. After washing, leave the lid open until the interior
is dry.
2. Check hoses to be sure there are no kinks or knots.
3. Your washer should not be installed where
temperatures will go below freezing, as damage to
the washer could result.
4. To clean, occasionally wipe exterior with a clean
damp sponge or cloth. Do not use polish on
plastic parts.
5. Lifetime lubrication is done at the factory, so your
washer never needs to be oiled or greased.
6. Do not lay heavy or sharp objects on top of your
washer.
The top of the washer should not be used for
removing stains from garments. Some stain
removers, such as rust remover, will mar the finish.
Remove pins, buckles or other sharp objects from
clothes to prevent scratching interior parts.
Clothes should not be stored in washer.
Bleach, detergent, solvents, etc. spilled on the top
of your washer that are allowed to remain will
remove the glossy finish. Remove all spills with a
damp, soft cloth.
If you close your home for the winter, have a service
technician drain the washer. Unplug cord from
electrical outlet and disconnect hoses from faucets.
Cleaning the Interior
Clean the interior of the washer periodically to remove
any dirt, soil, odor, mold, mildew or bacteria residue
that may remain in the washer as a result of washing
clothes. We recommend taking the following steps
every 60 to 120 days to clean and freshen your washer
interior. The frequency with which the washer should
be cleaned and freshened depends on factors such as
usage, the amount of dirt, soil or bacteria being run
through your washer, or the use of cold water. Failure
to follow these instructions may result in unsatisfactory
conditions, including unpleasant odor and/or
permanent stains on the washer or washload.
To clean and freshen the washer interior:
1. Add a measured amount of chlorine bleach to the
bleach dispenser, following package directions.
2. Add 1//4 cup of detergent to the tub.
3. Run the washer without a load through a complete
cycle using hot water.
/4. Repeat the process if necessary.
13
Troubleshooting
Won't Fill
Won't Agitate
Won't Spin
or Drain
Load is Wet
Stops
Leaks Water
Is Noisy
Fills with
the Wrong
Temperature
Water
Cycle Selector
Advances Through
Off
Plug cord into live electrical outlet.
Check fuse or reset circuit breaker.
Turn the control dial to proper cycle and restart the washer.
Turn both faucets on fully.
Straighten inlet hoses.
Disconnect hoses and clean screens. Hose filter screens may be plugged.
Check fuse or reset circuit breaker.
Make sure the lid is completely closed.
Turn the control dial to proper cycle and restart the washer.
Pauses are normal. Wait and see if the washer will start again.
Check fuse or reset circuit breaker.
Straighten drain hoses. Eliminate kinked hoses. If there is a home drain restriction, call for
drain service.
Close lid and restart the washer. For your safety, washer will not spin unless the lid is closed.
Suds lock - caused by too much suds. Rewash without detergent. Use correct amount of a
low-sudsing detergent.
Unevenly distributed load. Redistribute the load, close the lid and restart the washer. Check for
leveling. Be sure water level is acceptable for load size.
A normal spin speed is recommended for heavy loads like jeans or towels.
Plug cord into live electrical outlet.
Check fuse or reset circuit breaker.
Close lid and restart the washer. For your safety, washer will not agitate or spin unless lid is closed.
This may be a pause in the cycle. Wait briefly and it may start.
Make sure hose connections are tight.
Make sure end of drain hose is correctly inserted and secured to drain facility.
Avoid extended soaking - soak for 30 minutes or less.
Avoid overloading.
Be sure washer is leveled properly as outlined in installation manual.
Weak floors can cause vibration and walking.
Operating sounds will vary depending on agitation speed.
Turn both faucets on fully.
If equipped with a temperature selector dial, be sure it is set directly on a temperature setting and
not between settings.
Make sure temperature selection is correct.
While the washer is filling, you may notice just hot and/or just cold water entering the tub when
cold or warm wash temperatures are selected. This is a normal function of the Automatic
Temperature Control (select models_ feature as the washer determines the temperature of
the water.
If Auto Temperature Control (select models_ is selected, cold water may feel warmer than cold
water from the tap.
Make sure hoses are connected to correct faucets and inlet connections. Be sure water supply is
regulated correctly. Flush water line before filling washer.
Check the water heater. It should be set to deliver a minimum 120° F (49° C_hot water at the tap.
Also check water heater capacity and recovery rate.
Disconnect hoses and clean screens. Hose filter screens may be plugged.
Extra Rinse (select models_ is selected.
14
Wurru,t¥& Service
CUSTOMER'S SOLE AND EXCLUSIVE
REMEDY UNDER THIS LIMITED
WARRANTY SHALL BE PRODUCT REPAIR
AS PROVIDED HEREIN. IMPLIED
WARRANTIES, INCLUDING WARRANTIES
OF MERCHANTABILITY OR FITNESSFOR
A PARTICULAR PURPOSE,ARE LIMITED
TO ONE YEAR ORTHE SHORTEST
PERIODALLOWED BY LAW. MAYTAG
CORPORATION SHALL NOT BE LIABLE
FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGES. SOME STATESAND
PROVINCES DO NOT ALLOW THE
EXCLUSION OR LIMITATION OF
INCIDENTAL OR CONSEQUENTIAL
DAMAGES, OR LIMITATIONS ON THE
DURATION OF IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS,SO
THESE EXCLUSIONS OR LIMITATIONS
MAY NOT APPLY TOYOU. THIS
WARRANTY GIVESYOU SPECIFICLEGAL
RIGHTSAND YOU MAY ALSO HAVE
OTHER RIGHTS,WHICH VARY STATETO
STATEOR PROVINCE TO PROVINCE.
What is Not Covered By These Warranties
1. Conditions and damages resulting from any of the following:
a. Improper installation, delivery, or maintenance.
b. Any repair, modification, alteration, or adjustment not authorized by the
manufacturer or an authorized servicer.
c. Misuse, abuse, accidents, unreasonable use, or acts of God.
d. Incorrect electric current, voltage, electrical and/or gas supply.
e. Improper setting of any control.
2. Warranties are void if the original serial numbers have been removed, altered,
or cannot be readily determined.
3. Light bulbs, water filters and air filters.
4. Products purchased for commercial or industrial use.
5. The cost of service or service call to:
a. Correct installation errors. Forproducts requiring ventilation, rigid metal
ducting must be used.
b. Instruct the user on the proper use of the product.
c. Transport the appliance to and from the servicer.
6. Any food loss due to refrigerator or freezer product failures.
7. Expenses for travel and transportation for product service in remote locations.
8. Outside of the United States and Canada this warranty does not apply.
Contact your dealer to determine if another warranty applies.
9. Consequential or incidental damages sustained by any person as a result of
any breach of these warranties. Some states do not allow the exclusion or
limitation of consequential or incidental damages, so the above exclusion may
not apply.
If You Need Service
First see the Troubleshooting section in your Use and Care Guide or call the
dealer from whom your appliance was purchased or call Maytag Services, LLC,
Customer Assistance at 1-800-688-9900 USA and 1-800-688-2002 Canada to
locate an authorized servicer.
Besure to retain proof of purchase to verify warranty status. Refer to WARRANTY
for further information on owner's responsibilities for warranty service.
If the dealer orservice company cannot resolve the problem, write to Maytag
Services, LLC,Attn: CAIR Center, EO. Box 2370,Cleveland,TN 37320-2370,or call
1-800-688-9900 USA and 1-800-688-2002 Canada. U.S.customers using
TTY for deaf, hearing impaired or speech impaired, call 1-800-688-2080.
User'sguides, service manuals and parts information are available from Maytag
Services, LLC,Customer Assistance.
Notes: When writing or calling about a service problem, please include:
a. Your name, address and telephone number;
b. Model number and serial number;
c. Name and address of your dealer or servicer;
d. A clear description of the problem you are having;
e. Proof of purchase (sales receipt).
15
MAV-1
lUl
Table des mati_res
Importantes consignes
de s_curit_ ............. 17-18
Caractbristiques
sp6ciales .............. 29-30
Fonctionnement ........ 19-20
Nettoyage et entretien ..... 30
Utilisation des commandes
ModUles _ trois vitesses .... 21-22
Modbles _ quatre vitesses ... 23-25
ModUles _lectroniques ..... 26-28
Recherche des pannes .. 31-32
Garantie et service
aprbs-vente ............... 33
Guia de uso y cuidado ..... 34
Importnntesconsignesdesecurit6
Ce qu'il faut savoir _ propos
des consignes de s_curitd
Les consignes de s6curit6 et les mises en garde pr6sent6es
dans ce guide ne couvrent pas toutes les situations
possibles. Faire preuve de jugement, de prudence et
d'attention Iors de I'installation, de I'entretien et de
I'utilisation de I'appareil.
Lorsque survient un probleme ou une situation inhabituelle,
toujours communiquer avec le fabricant.
Reconnaissez les _tiquettes, phrases
ou symboles sur la securite
17
Importnntesconsignesdesecurit6
1. Lire toutes les instructions avant d'utiliser la laveuse.
2. Comme avec tout equipement fonctionnant _ I'electricite
et comportant des pieces mobiles, il existe toujours des
possibilites de danger. Pour utiliser cette machine dans
les meilleures conditions de securite, I'operateur doit se
familiariser avec les instructions de fonctionnement de
I'appareil et user de prudence pendant son utilisation.
3. Ne pas installer ni remiser la laveuse dans un endroit
ot] elle est exposee aux intemperies.
4. Installer la laveuse et la mettre de niveau sur un
plancher pouvant supporter son poids.
5. Cet appareil doit etre correctement mis _ la terre. Ne
jamais brancher le cable electrique d'une laveuse sur
une prise murale non mise _ la terre conformement aux
codes Iocaux et nationaux. Voir les instructions
d'installation pour la mise _ la terre de cette machine.
6. Pour eviter les risques d'incendie ou d'explosion :
a. Ne pas laver d'articles qui ont auparavant ete
nettoyes ou laves _ I'aide d'essence, de solvants de
nettoyage _ sec ou d'autres produits explosifs ou
inflammables, ou qui en sont imbibes ou eclabousses,
car ces substances produisent des vapeurs qui
peuvent s'enfiammer ou exploser. Laver _ la main et
secher _ I'air tout article contenant ces substances.
Tout tissu sur lequel des solvants de nettoyage ont
ete utilises ou qui est sature de liquides ou solides
inflammables ne doit pas etre mis dans la laveuse
avant que toute trace et toute vapeur de ces liquides
ou solides ne soient completement eliminees.
Ces produits comprennent I'acetone, I'alcool
denature, I'essence, le kerosene, certains produits de
nettoyage menagers, les detachants, la terebenthine,
les cires et les dec@ants de cire.
b. Ne pas ajouter d'essence, de solvants de nettoyage
sec ou toute autre substance inflammable ou
explosive _ I'eau de lavage. Cessubstances produisent
des vapeurs qui pourraient s'enflammer ou exploser.
c. Dans certaines conditions, il peut y avoir production
d'hydrogene dans un systeme de chauffage d'eau qui
n'est pas utilise pendant 2 semaines ou plus.
L'HYDROGI_NEESTUN GAZ EXPLOSIF.Si le systeme
de chauffage d'eau n'est pas utilise sur une telle
duree, ouvrir tousles robinets d'eau chaude et laisser
couler I'eau pendant plusieurs minutes avant d'utiliser
la laveuse ou la ensemble laveuse-secheuse. Ceci
elimine toute accumulation d'hydrogene. Ce gaz etant
inflammable, ne pas fumer ni utiliser de flamme vive
pendant cette procedure.
d. Ne pas laver ou secher d'articles taches d'huile
vegetale ou de cuisson. Ces articles pourraient etre
encore impregnes d'huile apres la lessive. Pour cette
raison, le tissu pourrait emettre des fumees ou
prendre feu de lui-meme.
Z Ne pas mettre la main ou le bras dans la laveuse si
I'agitateur ou cuve est en mouvement.
8. Ne pas permettre aux enfants ou aux animaux familiers
de jouer sur I'appareil, _ I'interieur ou en face de celui-
ci. Une supervision etroite est necessaire Iorsque
I'appareil est utilise _ proximite d'enfants ou d'animaux
familiers.
9. Ne pas modifier les mecanismes de commande.
10. Ne pas r@arer ou remplacer une piece de la laveuse
ou proceder _ un d@annage, sauf si les instructions
publiees le recommandent et que la personne effectuant
la r@aration les comprend et possede les
connaissances voulues pour les executer.
11. Debrancher le cordon d'alimentation electrique avant
d'essayer de r@arer la laveuse. Les reparations ne
doivent etre effectuees que par du personnel qualifi&
12. I'agitateur ne doit pas etre retire. S'il est retire, le
replacer en I'enfon(_ant_ fond, puis serrer la vis de
blocage avant de faire fonctionner la laveuse.
13. Conserver tousles produits de lessive, les detergents,
les produits de blanchiment, etc., hors de portee des
enfants, et de preference dans une armoire fermee
cle. N'utiliser ces produits que selon les directives du
fabricant. Observer tousles avertissements paraissant
sur les etiquettes des differents produits.
14. S'assurer que toute la zone autour de la laveuse et en
dessous, soit degagee de toute accumulation de
materiaux combustibles comme charpie, papier, chiffons,
essence et tout autre liquide ou vapeur inflammable.
15. Ne pas melanger de javellisant et d'ammoniaque ou
d'acides (tels que du vinaigre ou du produit pour enlever
la rouille) pour une meme charge de linge. Desvapeurs
nocives peuvent se former.
16. Ne pas laver d'articles en fibre de verre _ la laveuse. De
petites particules peuvent se coller sur le linge lave par
la suite et provoquer des irritations cutanees.
1Z Apprets resistants aux flammes - suivre attentivement
les instructions du fabricant du vetement. Un vetement
incorrectement lave ou seche pourrait perdre son appret
ignifuge.
18. Avant de mettre la laveuse hors service ou au rebut,
retirer la porte du compartiment de lavage.
19. Les tuyaux d'alimentation se deteriorent progressivement.
Inspecter les tuyaux _ intervalle regulier; rechercher
dilatations, ecrasements, coupures, fuites et indices
d'usure. Remplacer les tuyaux apres 5 ans de service.
CONSERVER CES INSTRUCTIONS
18
I:oncdonnement
Ddtergent
Utiliser du d6tergent liquide ou en poudre. Pour des
r_sultats optimums, ajouter suffisamment de
d_tergent darts la laveuse AVANT de la remplir et
r_gler la temperature de I'eau _ plus de 16 °C (60 °F).
Utiliser la quantit6 de d6tergent qui convient _ la charge,
au degr6 de salet6 et _ la duret6 de I'eau. Utiliser plus de
d6tergent si I'eau est dure et que la charge est tr6s sale.
Si I'eau est douce ou que la charge est peu sale, utiliser
moins de d6tergent. (Voirles instructions du fabricant.)
Essuyer la laveuse si elle se trouve 6clabouss6e de
d6tergent.
Chargement
Pour des r6sultats optimums, mettre du d6tergent dans la
cuve avant d'ajouter le linge.
Mettre le linge sec, non pli6 sans le tasser dans la laveuse,
en remplissant le panier jusqu'au rang sup6rieur de trous
pour une charge maximum.
Ne pas enrouler de grands articles tels que des draps
autour de I'agitateur.
Pour une meilleure circulation, m61anger les petits et les
grands articles. Laver les articles volumineux comme les
couvertures s@ar6ment.
Lors du lavage d'articles infroissables, fragiles, de lainages
lavables ou d'articles en tricot _ mailles laches, ne jamais
utiliser un niveau d'eau inf_rieur au r6glage MEDIUM
(moyen). IIs auront moins tendance _ r6tr6cir, _se froisser
et les coutures tiendront mieux.
Refermer soigneusement le couvercle pour qu'il ne
claque pas.
19
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52

Maytag MAV2757AWW Le manuel du propriétaire

Catégorie
Machines à laver
Taper
Le manuel du propriétaire