Power Fist 8785081 Le manuel du propriétaire

Marque: Power Fist

Modèle: 8785081

Catégorie: Système de soudage

Taper: Le manuel du propriétaire

V4.2 8785081

Please read and understand all instructions before use. Retain this manual for

future reference.

User Manual

200A AC/DC Dial Control

TIG Welder 202KE

8785081 200A AC/DC Dial Control TIG Welder 202KE V4.2

2 For technical questions call 1-800-665-8685

SPECIFICATIONS

120V 230V

Rating (Voltage, Frequency)

120/230V ±15%, 60Hz

Phase

Single

Input Current

20A

31A

Rated Input Capacitance

2.4 kVA

7.5 kVA

No Load Voltage

65V

Insulation Class

Protection Class

IP21S

Cooling Type

Fan Cooled

Dimension (L × W × H)

19-3/4 x 9-1/2 x 16-1/8 in.

(50.1 x 24.1 x 43.8 cm)

Weight

17 kg

MMA (Stick)

Current

20 to 65A

20 to 160A

Electrode Size

1/16 in.

3/16 in.

Duty Cycle (10 min.)

35%

Max. Metal Thickness

1/16 in.

5/16 in.

DC TIG

Current

10 to 95A

10 to 200A

Electrode Size

1/8 in.

3/16 in.

Duty Cycle (10 min.)

35%

Max. Metal Thickness

1/8 in.

1/2 in.

DC Pulse TIG

Current

10 to 95A

10 to 200A

Pulse Frequency

50% Peak Current

Duty Cycle (10 min.)

35%

Max. Metal Thickness

1/8 in.

1/2 in.

AC TIG

Current

20 to 95A

20 to 200A

Exchange Frequency

50 to 150Hz

(Balance) Cleaning Width

50 to 85%

Pulse Frequency

0.2

～

20Hz

Duty Cycle (10 min.)

35%

Max. Metal Thickness

1/8 in.

1/2 in.

200A AC/DC Dial Control

TIG Welder 202KE

V4.2 200A AC/DC Dial Control TIG Welder 202KE 8785081

Visit www.princessauto.com for more information 3

AC Pulse TIG

Peak Current

～

95A

～

200A

Base Current

50% Peak Current

Exchange Frequency

～

150Hz

(Balance) Cleaning Width

50%

～

85%

Pulse Frequency

0.2

～

20Hz

Duty Cycle (10 min.)

35%

Max. Metal Thickness

1/8 in.

1/2 in.

INTRODUCTION

The 200 AC/DC Dial Control TIG Welder 202KE produces smooth, stable arcs with

AC or DC circuits, making it the go-to option for serious DIYers and fabricators.

Among its many features are a digital-controlled display, easy, single knob

operation, AC/DC current and built-in thermal overload protection. It welds carbon

steel, cast iron, stainless steel, copper, aluminum alloy and magnesium alloy.

SAFETY

WARNING! Read and understand all instructions before using this tool. The

operator must follow basic precautions to reduce the risk of personal injury

and/or damage to the equipment.

Keep this manual for safety warnings, precautions, operating or inspection and

maintenance instructions.

HAZARD DEFINITIONS

Please familiarize yourself with the hazard notices found in this manual. A notice

is an alert that there is a possibility of property damage, injury or death if certain

instructions are not followed.

DANGER! This notice indicates an immediate and specific hazard that will

result in severe personal injury or death if the proper precautions

are not taken.

WARNING! This notice indicates a specific hazard or unsafe practice that

could result in severe personal injury or death if the proper

precautions are not taken.

CAUTION! This notice indicates a potentially hazardous situation that may result

in minor or moderate injury if proper practices are not taken.

8785081 200A AC/DC Dial Control TIG Welder 202KE V4.2

4 For technical questions call 1-800-665-8685

NOTICE! This notice indicates that a specific hazard or unsafe practice will

result in equipment or property damage, but not personal injury.

WORK AREA

1. Operate in a safe work environment. Keep your work area clean, well-lit and

free of distractions.

2. Remove all unnecessary people from the work area when welding.

Anyone remaining in the work area must wear the appropriate welding

safety equipment.

3. Store tools properly in a safe and dry location. Keep tools out of the reach

of children.

4. Do not weld on damp surfaces that can transmit the electric current

without taking precautions for the welder and bystanders. The electrode,

welding head and nozzle are electrically ‘hot’.

5. Do not install or use in the presence of flammable gases, dust or liquids.

6. Welding sparks and ejected molten slag can start a fire. Remove

combustible materials within 39 ft (12 metres) of the welding unit. See Fire

and Explosion Precautions.

7. Have a fire extinguisher readily available (see Fire and Explosion

Precautions).

8. Erect protective screens or barriers to protect bystanders from the flash

and glare; warn others in the area not to watch the arc. Do not strike a

welding arc until all bystanders and you (the user) have welding shields

and/or helmets in place.

9. Keep the welding unit at least one foot from any wall or structure.

10. Check that the work area is free from fires, sparks or hot debris

before leaving.

PERSONAL SAFETY

WARNING! Wear personal protective equipment approved by the Canadian

Standards Association (CSA) or American National Standards Institute (ANSI).

V4.2 200A AC/DC Dial Control TIG Welder 202KE 8785081

Visit www.princessauto.com for more information 5

HEAD PROTECTION

DANGER! Never look directly at the welding arc without the proper

protection. The light can cause flash burn damage and impair vision.

Although treatment is possible, multiple occurrences can result in

permanent eye damage.

1. Protect your eyes from welding light by wearing a welder's helmet fitted

with a filter shade suitable for the type of welding you are doing. The

welding process produces intense white light, infrared and ultraviolet light,

these arc rays can burn both eyes and skin.

a. Consult the Welding Shade Guide in Appendix A for the minimum

shade to protect the eyes based on the amperage and type of welding.

2. An opaque helmet will protect against the ultraviolet or infrared light. A

helmet will also protect against ejected hot material and slag. The helmet

should protect the face, forehead, ears and neck.

3. Wear a fire-resistant head covering like a skullcap or balaclava hood to

protect your head when the faceplate is down or when using a welding

hand-held face shield.

4. Wear ventilated safety goggles beneath the welding helmet or behind the

hand-held face shield. The cooling weld bead may fragment or eject slag that

can damage the eyes, when the helmet or hand-held face shield is not in place.

a. Eye protection equipment should comply with CSA Z94.3-07 or ANSI

Z87.1 standards based on the type of work performed.

5. Wear fire resistant earplugs when welding overhead to prevent spatter or

slag from falling into ear.

PROTECTIVE CLOTHING

1. Wear a leather apron or jacket, leather welding gloves and full foot protection.

Choose clothing fabrics that resist sparks, heat, flames and splashes of molten

material. Artificial fabrics may burn and melt, resulting in a more severe injury.

a. Wear welding capes and sleeves when performing overhead welding.

2. Do not wear clothes or protective gear that are frayed, oily or greasy as

they may ignite from the heat or ejected slag and sparks.

3. Wear thick clothes that do not expose the skin. Ultraviolet or infrared light

can burn skin with sufficient exposure.

8785081 200A AC/DC Dial Control TIG Welder 202KE V4.2

6 For technical questions call 1-800-665-8685

4. Do not wear clothing that can hold hot debris or sparks such as pant cuffs,

shirt pockets or boots. Choose clothing that has flaps over pockets or wear

clothing to cover the openings such as pant legs over the boots or an apron

over the shirt.

5. Gloves shall should contain an insulating lining to protect against an

electric shock.

6. Rubber soled footwear or electrically insulated work boots are

recommended while working with a welding unit. The non- skid sole is will

also help maintain footing and balance during work.

a. Select boots with steel toe protection to prevent injury from falling objects.

RESPIRATORS

1. Respiratory protection is needed when ventilation is not sufficient to

remove welding fumes or when there is risk of oxygen deficiency.

a. Wear a NIOSH approved respirator when working on materials that

produce dust or particulate matter.

2. Work in a confined space only if it is well ventilated or while wearing an air-

supplied respirator. Welding fumes and gases can displace air and lower

the oxygen level causing injury or death. Be sure the breathing air is safe

(See Fumes and Gases).

3. The user can take the additional precaution of informing another person in

the work area of the potential danger, so that person can watch for

indications that the user is suffering from oxygen deprivation.

PERSONAL PRECAUTIONS

Control the tool, personal movement and the work environment to avoid

personal injury or damage to the tool.

1. Do not operate any tool when tired or under the influence of drugs, alcohol

or medications.

2. Avoid wearing clothes or jewelry that can become entangled with the

moving parts of a tool. Keep long hair covered or bound.

3. Remove all jewelry or metal items from your person before welding. Metal

items may connect to the welding unit’s electrical circuit, causing an injury

or death.

V4.2 200A AC/DC Dial Control TIG Welder 202KE 8785081

Visit www.princessauto.com for more information 7

4. Do not overreach when operating the tool. Proper footing and balance enables

better control in unexpected situations.

5. Support the workpiece or clamp it to a stable platform. Holding the

workpiece by hand or against your body may lead to personal injury.

6. Do not wear any personal grooming products that are flammable, such as

hair preparations, perfume or cologne with an alcohol base.

7. Remove any combustibles, such as butane lighters or matches, from your

person before doing any welding. Hot welding sparks may light the

matches or ignite leaking lighter fuel.

SPECIFIC SAFETY PRECAUTIONS

WARNING! DO NOT let comfort or familiarity with product (gained from

repeated use) replace strict adherence to the tool safety rules. If you use

this tool unsafely or incorrectly, you can suffer serious personal injury.

1. Use the correct tool for the job. This tool was designed for a specific function.

Do not modify or alter this tool or use it for an unintended purpose.

2. Arc welding requires the use a hand-held face shield or helmets with full

face protection per CSA standard Z94.3.1.

3. Protect against reflected arc rays. The rays can reflect off a shiny surfaces

behind the user, into the helmet and off the filter lens into the eyes.

Remove or cover any reflective surface behind the user such as a glossy

painted surface, aluminum, stainless steel or glass.

4. Welding produces sparks and molten slag. A cooling bead can eject chips

or fragments of slag. Any of these can cause direct harm to the eyes or

skin of the user or bystanders.

5. Immediately replace a cracked or broken helmet or a scratched or

damaged lens filter to avoid damage to the eyes or face from arc flash or

ejected molten material.

6. Do not allow the welding electrode to accidentally touch the ground clamp or

grounded work. An arc flash will result from contact and can injury the

unprepared user and bystanders.

7. Do not handle hot metal or electrode stubs with bare hands. Handling may result

in a burn injury.

8785081 200A AC/DC Dial Control TIG Welder 202KE V4.2

8 For technical questions call 1-800-665-8685

8. Do not use the welding unit if personal movement is confined or if there is a

danger of falling.

9. Keep all panels and covers securely in place when operating the welding unit.

10. Insulate the ground clamp when not connected to a workpiece to prevent

contact with any metal object.

11. Do not operate the welding unit if the torch, electrode holder, welding cable or

ground cable are wet. Do not immerse them in water. These components and

the welding unit must be completely dry before attempting to use them.

12. Never dip the electrode in water for cooling.

13. Remove the electrode from the holder when not in use.

14. Do not point the torch or electrode holder at any body part of yourself or at

anyone else.

15. Do not use a welding unit to thaw frozen pipes.

16. Insulate yourself from the work and the ground using dry insulation. Make

certain that the insulation is large enough to cover your full area of physical

contact.

17. When not welding, make certain that no part of the electrode circuit is touching

the workpiece or the ground. Accidental contact can cause overheating and

create a fire hazard.

18. Maintain good ventilation of the louvers on this equipment. Good

ventilation is of critical importance for the normal performance and service

life of this equipment.

19. When working above floor level, use a safety belt to protect yourself from a

fall should you get a shock.

20. The electrode, electrode reel, welding head, nozzle and semiautomatic

welding torches are electrically ‘hot’ when the welding unit is in

semiautomatic or automatic wire welding mode.

21. The welder must be horizontal. An incline of 10º or less is acceptable.

FIRE AND EXPLOSION PRECAUTIONS

Arc welding can produce sparks, hot slag or spatter, molten metal drops and hot

metal parts that can start fires.

V4.2 200A AC/DC Dial Control TIG Welder 202KE 8785081

Visit www.princessauto.com for more information 9

1. Clear the floor and walls of an area of all combustible and/or flammable

materials up to 39 ft (12 metres) away from the welding unit. Hot debris

ejected during welding can land at a considerable distance away. Solid

floors of concrete or masonry is the preferred working surface.

a. Cover any combustible material with fire resistant covers or shields, if

it cannot be removed. The covering must be tight and should not

leave openings for sparks or ejected slag to enter.

b. Check both sides of a panel or wall for combustible material. Remove

the combustible material before welding.

2. A combustible floor should be protected with a fire resistant covering.

Alternatives are to spray the floor with water to keep it wet for the duration

of the welding or cover with damp sand. Care must also be taken to avoid

an electric shock when this is done. A combustible floor directly laid onto

concrete does not need to be sprayed with water.

3. Seal cracks and openings to adjacent areas that a spark or slag can enter.

Seal any openings found with a fire-resistant cover. Shut doors and windows

that do not provide ventilation or erect protective screens in front of them

when possible.

4. Avoid welding near hydraulic lines or containers containing flammable

contents.

5. Do not perform any welding work on containers that held flammable or

toxic substance, until they are cleaned by a person trained in removing

toxic and flammable substances and vapours per the American Welding

Standard AWS F4.1.

6. Open a container before performing any welding work on it. The heat

generated by the welding process will cause the air and gases to expand.

The internal pressure may cause a sealed or closed container to rupture,

possibly causing an injury or death.

7. Do not weld pipes or metal that are covered in combustible material or in

contact with combustible structure such as a wall. Only weld if the

covering can be safely removed.

a. Follow all safety precautions and legal requirements before welding a

workpiece that contains Asbestos or attempting to remove the

Asbestos covering. This requires expert knowledge and equipment.

8785081 200A AC/DC Dial Control TIG Welder 202KE V4.2

10 For technical questions call 1-800-665-8685

b. Molten slag can run down the inside and outside of a pipe and start a

fire. Be aware where the pipe terminates and take precautions.

8. Do not weld a panel that is a sandwich construction of combustible and

metal materials.

9. Have a fire extinguisher available for immediate use. A dry chemical fire

extinguisher for Types A, B and C is suggested.

a. Welding a combustible metal like zinc, magnesium or titanium

requires a Type D fire extinguisher.

b. Do not use liquid based fire extinguishing methods near the electric

arc welding unit, as it may cause a shock hazard.

10. Ventilation systems should be positioned so sparks or molten slag isn’t

carried to an adjacent area.

11. Have a Fire Watcher observing areas outside of the welder’s view, such as

the opposite side of a wall or behind the welder. A fire may also start on the

other side of a structure that could not be removed. The Fire Watcher will

extinguish a fire or raise the alarm to evacuate if the fire cannot be

contained by the extinguishing equipment.

a. A fire watch extends at least 30 minutes after the welding is complete to

ensure there are no fires caused by smoldering sparks or ejected material.

FUMES AND GASES

WARNING! Stop welding and move to a location with ventilation if your eyes,

nose or throat become irritated. This indicates the ventilation is not adequate

to remove the fumes. Do not resume welding until the ventilation is improved

and the discomfort ceases. Seek medical attention if the symptoms do not

diminish or if the welder experiences nausea, dizziness or malaise.

Welding may produce hazardous fumes and gas during the welding process. A well

ventilated work area can normally remove the fumes and gases, but sometimes the

welding produces fumes and gases that are hazardous to your health.

1. Only work in a confined space if the area is well ventilated or while wearing

a respirator or an air-supplied respirator. Welding fumes and gases can

displace air and lower the oxygen level causing injury or death. Be sure the

breathing air is safe. Always have a trained watchperson nearby.

V4.2 200A AC/DC Dial Control TIG Welder 202KE 8785081

Visit www.princessauto.com for more information 11

a. If ventilation in the work area is poor, use an approved air-supplied

respirator. All the people in the work area must also have air-supplied

respirators.

b. Oxygen displacement can occur in confined areas when the shielding

gas fills the area and pushes out air.

2. Avoid positions that allow welding fumes to reach your face. Always attempt to

weld ‘upwind’ of the workpiece with the airflow across the face of the welder.

Airflow from behind may create a low pressure area in front of the welder and

draw the fumes to the person.

3. Ventilate the work area to remove welding fumes and gases. The fumes

and gases should be drawn away from the user.

a. Ventilation should be enough to disperse fumes, but not enough to

disturb the shielding gas or flame during welding.

b. Ventilation exhaust shall be directed to a non-work area to avoid

exposing other people to potential toxic or dangerous fumes.

c. Air removed from the work area by the ventilation system must be

replenished with fresh air to avoid oxygen starvation or a build-up of fumes

or gases. Only use air to provide ventilation. Any other combination of

gases may be explosive or toxic to people in the work area.

d. Ventilation methods that remove gas and fumes from the welding

point before they reach the welder’s face should be given preference.

4. Avoid welding in a work area that has vapours from cleaning, degreasing or any

spraying operations. The heat and light from welding can react with the vapour

and form irritating or potentially toxic gases. Wait for the vapours to disperse.

5. Consult the manufacturer's Safety Data Sheets (SDS) for instructions and

precautions about metals, consumables, coatings, cleaners and degreasers.

a. Do not weld on coated metals such as galvanized, lead or cadmium

plated steel, unless the coating is removed from the weld area. The

coatings and any metals containing these elements can give off toxic

fumes during the welding process.

b. Do not weld, cut or heat lead, zinc, cadmium, mercury, beryllium or

similar metals without seeking professional advice and inspection of the

welding area’s ventilation. These metals produce extreme toxic fumes,

which can cause discomfort, illness and death.

8785081 200A AC/DC Dial Control TIG Welder 202KE V4.2

12 For technical questions call 1-800-665-8685

c. Do not weld or cut near chlorinated solvents or in areas that

chlorinates solvents can enter. The heat or ultraviolet light of the arc

can separate chlorinated hydrocarbons into a toxic gas (phosgene)

that can poison or suffocate the user or bystanders.

6. Check the Safety Data Sheet for the proper handling and safety precautions

for consumable welding rods as the coating can have multiple chemicals.

COMPRESSED GAS CYLINDER PRECAUTIONS

WARNING! Improper handling or maintenance of compressed gas cylinders

and regulators can result in serious injury or death. Do not use a cylinder or

its contents for anything other than its intended use.

1. Only use inert or nonflammable gas with the welding unit such as Carbon

Dioxide, Argon or Helium with the welding unit.

a. Never use flammable gases. They will ignite and may result in an explosion

or fire that can cause death or injury.

2. Do not attempt to mix gases or refill a gas cylinder. Exchange a cylinder or

have it refilled by a professional service.

3. Do not deface or alter the name, number or other markings on a cylinder. Do not

rely on a cylinder’s colour to identify the contents. Do not connect a regulator to

a cylinder that contains a gas that the regulator was not designed to handle.

4. Do not expose a cylinder to excessive heat, sparks, slag, flame or any other

heat source.

a. A cylinder exposed to temperatures above 130 °F will require water

spray cooling. This method may not be compatible with electric

welding units due to the hazard of electrocution.

5. Do not expose a cylinder to electricity of any kind.

6. Do not attempt to lubricate a regulator. Always change a cylinder carefully

to prevent leaks and damage to the cylinder’s walls, valve or safety

devices.

7. Gases in the cylinder are under pressure. Protect the cylinder from bumps,

falls, falling objects and harsh weather. A punctured cylinder under

pressure can become a lethal projectile. If a cylinder is punctured, do not

approach until all pressure is released.

a. Protect the valve and regulator. Damage to either can result in

V4.2 200A AC/DC Dial Control TIG Welder 202KE 8785081

Visit www.princessauto.com for more information 13

regulator’s explosive ejection from the cylinder.

8. Always secure a gas cylinder in a vertical position to a welding cart or

other fixed support with a steel chain, so it cannot be knocked over.

a. Away from areas where they may be struck or subjected to physical

damage.

b. A safe distance from arc welding or cutting operations and any other

source of heat, sparks or flame.

b. Do not use as an improvised support or roller.

9. Always place the cylinder cap securely on the cylinder unless it is in use or

being serviced.

10. Do not use a wrench or hammer to open a cylinder valve that cannot be

opened by hand. Notify your supplier for instructions.

11. Do not modify or exchange gas cylinder fittings.

12. Close the cylinder valve and immediately remove the faulty regulator from

service for repair, if any of the following conditions exist:

a. Gas leaks externally.

b. Delivery pressure continues to rise with the downstream valve closed.

c. The gauge pointer does not move off the stop pin when pressurized or

fails to return to the stop pin after pressure is released.

13. Do not attempt to make regulator repairs. Send faulty regulators to the

manufacturer's designated repair center.

14. Do not weld on the gas cylinder.

15. Keep your head and face away from the cylinder valve outlet when opening the

cylinder valve.

16. Compressed gas cylinders must not be located in a confined space with the

person welding to prevent the possibility of leaks displacing the oxygen.

ELECTRICAL SAFETY

1. Do not come into physical contact with the welding current circuit. The

welding current circuit includes:

a. The workpiece or any conductive material in contact with it.

b. The ground clamp.

8785081 200A AC/DC Dial Control TIG Welder 202KE V4.2

14 For technical questions call 1-800-665-8685

c. The electrode or welding wire;

d. Any metal parts on the electrode holder or wire feed torch.

e. The output terminals.

2. Insulate yourself from the electrical current and ground using electrical

insulating mats or covers big enough to prevent physical contact with the

workpiece or ground.

3. Connect the ground clamp as close to the welding area on the workpiece

as practical to prevent welding current from traveling along an unexpected

path and causing an electric shock or fire hazard.

a. An option is to attach the ground clamp to a bare metal spot on a

metal workbench. The circuit will complete as long as the workpiece

is also in full contact with the bare metal workbench.

4. Only use insulated connectors to join welding cables.

5. Ensure there are no contacts between the workpiece and work area that

would allow it to ground, other than through the ground cable circuit

6. Do not exceed the duty cycle or amperage required for the type of welding.

Excessive amperage can cause the deterioration of protective insulation

and create a shock hazard.

7. Unplug the welding unit when not in use as the unit as current is still

entering the unit, even when it is turned off.

8. Frequently inspect input power cable for wear and tear, replace the cable

immediately if damaged. Bare wiring is dangerous and can kill.

9. Do not use damaged, under sized or badly joined cables.

10. Do not disconnect the power cord in place of using the ON/OFF switch on

the tool. This will prevent an accidental startup when the power cord is

plugged into the power supply.

a. In the event of a power failure, turn off the machine as soon as the

power is interrupted. The possibility of accidental injury could occur, if

the power returns and the unit is not switched off.

11. Make certain the power source conforms to requirements of your

equipment (see Specifications).

V4.2 200A AC/DC Dial Control TIG Welder 202KE 8785081

Visit www.princessauto.com for more information 15

POWER TOOL PRECAUTIONS

This equipment requires a dedicated 120/230 VAC, 15 amp single-phase

alternating current circuit equipped with a similarly rated circuit breaker or slow

blow fuse. Do not run other appliances, lights, tools or equipment on the circuit

while operating this welding unit.

1. Do not drape or carry coiled welding cables on your body while the cables

are plugged into the welding unit.

2. Do not start the tool when the electrode is touching the workpiece.

3. Hold the tool by the insulated gripping surfaces when performing an operation

where it may contact hidden wiring or its own cord and cables. Contact with a

‘live’ wire will electrify exposed metal parts and shock the operator.

4. Take work breaks to prevent the tool's motor from overheating and/or

overloading. Refer to the welding unit’s duty cycle in Specifications.

5. Keep hands away from the electrode and the area it is being applied to

when the tool is in operation.

6. Do not connect the welding unit ground clamp to an electrical conduit. Do

not weld on an electrical conduit.

7. Do not touch the electrode or welded surface immediately after use. The

surface will be hot and may cause an injury.

8. Never use a tool with a cracked or worn electrode. Change the electrode

before using and discard the damaged one.

POWER CORD

1. Insert the power cord plug directly to the power supply whenever possible.

Extension cords are not recommended for use with this welding unit.

a. When an extension cord is required, use a welding version that

exceeds the welding unit’s maximum power requirement.

2. Do not operate this tool if the power cord is frayed or damaged, as an electric

shock or surge may occur, resulting in personal injury or property damage.

a. Inspect the tool's power cord for cracks, fraying or other faults in the

insulation or plug before each use.

b. Discontinue use if a power cord feels more than comfortably warm

while operating the tool.

8785081 200A AC/DC Dial Control TIG Welder 202KE V4.2

16 For technical questions call 1-800-665-8685

3. Keep all connections dry and off the ground to reduce the risk of electric

shock. Do not touch plug with wet hands.

4. Prevent damage to the power cord by observing the following:

a. Do not pull on the cord to disconnect the plug from an outlet.

b. Keep cord away from heat, oil, sharp edges or moving parts.

c. Place the electrical cord in a position that prevents it from contacting the

tool or workpiece. The cord should always stay behind the tool.

5. Make sure to locate the cord so that it is not stepped on, tripped over or

otherwise subject to damage or stress.

6. Do not wrap the cord around the tool, as sharp edges may cut insulation or

cause cracks if wound too tight. Gently coil cord and either hang on a hook

or fasten with a device to keep cord together during storage.

ELECTROMAGNETIC FIELDS

WARNING! Stop welding immediately and move away from the welding unit if

you feel faint, dizzy, nausea or shocks. Seek medical attention.

Electromagnetic Fields (EMF) can interfere with electronic devices such as

pacemakers. Anyone with a pacemaker should consult with their doctor before

working with or near an arc welding unit. The following steps can minimize the

effects of electromagnetic fields.

1. Twist or tape cables together and prevent coils.

2. Do not drape cables on your body.

3. Keep the welding power source and cables as far away from the user as

practical. A minimum of 24 in. is recommended.

4. Connect the workpiece clamp as close to the weld as possible, but lay the

electrode and workpiece cables away from the user.

5. Use the lowest current setting possible during welding.

6. Avoid long and regular bursts of energy while welding. Apply the electrode

in short strokes and intermittently. This will prevent the pacemaker from

interpreting the signal as a rapid heartbeat.

7. Do not allow the electrode to touch the metal while welding.

8. Keep the lead cable and ground cables on the same side of your body.

V4.2 200A AC/DC Dial Control TIG Welder 202KE 8785081

Visit www.princessauto.com for more information 17

9. Do not weld while carrying the welding power source.

10. Do not work next to, sit or lean on the welding power source.

UNPACKING

WARNING! Do not operate the tool if any part is missing. Replace the

missing part before operating. Failure to do so could result in a malfunction

and personal injury.

Remove the parts and accessories from the packaging and inspect for damage.

Make sure that all items in the contents are included.

Contents: • TIG Torch • Ground Lead • Quick Connector

• Gas Hose w/Clamp • Electrode Holder

IDENTIFICATION KEY

A Handle

B Control Panel

C Remote Connection

D Torch Switch Connector

E Positive (+) Power Socket

F Gas Outlet

G Negative (-) Power Socket

H Power LED

I Work LED

J Digital Display

K Overheating LED

L Overvoltage LED Power LED

M Welding Mode

N Welding Selection Key

O Adjustment Knob

P Welding Parameters

Q Parameter Selection Key

Fig. 1

Fig. 2

8785081 200A AC/DC Dial Control TIG Welder 202KE V4.2

18 For technical questions call 1-800-665-8685

OPERATION

Letter references in parenthesis (A) refer to the included Identification Key.

CONTROL PANEL SET-UP FOR WELDING

1. Turn on the machine. All LED indicators

will light up for two seconds before

turning off. The power indicator and

selected welding mode will remain on.

The digital display (J) will display the

current setting.

2. Select the welding mode (M) by pushing the welding selection key (N) on

the top or bottom half to move the selection. The LED will light up each

time a new welding selection is chosen.

3. Adjust the welding parameters (P) for the chosen welding mode.

a. Select the parameter by pressing the top or bottom of the parameter

selection key (Q). The selected parameter’s LED indicator will light up.

b. Turn the adjustment knob (O) to alter the parameter setting displayed

in the digital display (J).

4. Set each parameter in the same manner.

5. All parameters are locked in five seconds after there are no further adjustments.

SELECTING WELDING TYPE

DC TIG – Primary TIG welding method. The welding machine set-up can be

either DC positive or DC negative, based on the particular requirements for the

welding task.

Pulse DC TIG – Accuracy and neater welds result from this welding method.

The frequency determines how many times a second power is applied to the

material and filler stick. A lower frequency reduces the amount of overall heat

applied to the workpiece and permits more time for precision work. A higher

frequency increases the heat applied to the material, but allows you to increase

your travel speed to create a weld much quicker than normal without

compromising the weld strength. A foot pedal is often used for variable

frequency during the welding task.

Fig. 3

V4.2 200A AC/DC Dial Control TIG Welder 202KE 8785081

Visit www.princessauto.com for more information 19

AC TIG – Primary welding method for aluminum, magnesium and their metal alloys

Pulse AC TIG – Primary welding method for aluminum, magnesium and their

metal alloys. Reduces the welding heat input in the same way as Pulse DC TIG

to obtain a better weld.

DC Stick – Wide variety of electrodes are an option. DC stick arc is stable and

smoother than the AC stick arc. DC positive polarity results in higher material

penetration while DC negative is better at material deposition.

WELDING PARAMETERS

Each welding parameter has an adjustable range that you can set based on the

type of welding and welding materials. Some welding parameters do not apply

to all welding methods.

Current(A) – Available for all welding modes.

Adjust the amount of amps (heat) being applied to the weld. See Specifications

for the ranges available based on the type of welding and amount of voltage

being supplied (120/230V).

DC current is constant application of power to the weld.

AC current polarity switches between negative and positive, completing a cycle.

Pulse Frequency(Hz) – Available for Pulse DC TIG.

Adjust the frequency for a slower or quicker pulse. Pulse TIG creates a neater

weld and allows you to adjust the speed of creating the weld. The lower the

pulse the less overall heat is applied to the weld and material.

AC Frequency(Hz) – Available for AC TIG and Pulse AC TIG.

A higher frequency creates a narrower arc cone, penetrating deeper into the

material and forming a narrower bead weld with less build up. A lower

frequency will create a broad arc cone, with less penetration and more bead

build up.

AC Balance(%) – Available for AC TIG and Pulse AC TIG.

The electrode positive phase penetrates the material. The electrode negative

phase cleans (etches) the area around the weld of oxides, reducing the welding

temperature needed for aluminum and magnesium. The unadjusted AC balance

is approximately 50% penetrating (EP), 50% cleaning (EN).

8785081 200A AC/DC Dial Control TIG Welder 202KE V4.2

20 For technical questions call 1-800-665-8685

Change the etching duration in the welding cycle to increase or decrease the

area that is cleaned around the welding pool. A larger percentage will result in a

better removal of oxides, but reduces the heat devoted to penetrating the

material. A lower percentage will increase the penetration, but result in less

effective cleaning.

AUTO Balance / Frequency – Available for AC TIG and Pulse AC TIG.

Welding machine automatically determines the percentage of AC Frequency and

AC Balance for optimal penetration and cleaning during the welding task.

FOOT PEDAL CONTROL (NOT INCLUDED)

The control panel selections determine

the amount and frequency of current

delivered to the torch.

The foot pedal allows you to vary the

amount of welding current applied from

moment-to-moment. This increases the

precision control of heat for delicate

welding situations. The panel setting still

determines the maximum amperage that

the torch can generate.

OVERHEATING ALARM

Exceeding the duty cycle (see Specification)

can cause the welding machine to overheat

and shut down. The yellow overheating LED

(K) will illuminate and code E01 will appear in

the digital display (J). The welding machine

fan will continue to operate and cool the unit.

The welding machine will reset once it has cooled enough. Wait a further 10

minutes to allow the unit to cool below the overheating trigger threshold.

OVERVOLTAGE

This equipment has an automatic voltage compensation function, which enables

the unit to maintain the voltage within the given range.In case that the input

voltage or amperage exceeds the stipulated value, it is possible to damage the

Fig. 4

Fig. 5

La page charge ...

Power Fist 8785081 Le manuel du propriétaire

Marque: Power Fist

Modèle: 8785081

Catégorie: Système de soudage

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Power Fist 8785081 Owner's manual

Power Fist 8785081 Le manuel du propriétaire

Power Fist 8785081 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents