Power Fist 8785099 Le manuel du propriétaire

V4.0 8785099

Please read and understand all instructions before use. Retain this manual for

future reference.

User Manual

125A Inverter Flux Core

Welder

8785099 125A Inverter Flux Core Welder V4.0

2 For technical questions call 1-800-665-8685

SPECIFICATIONS

Input Voltage 120 AC

Input Current Rating 12.6A

Max. Amperage Draw 23A

Phase Single

Output Current Range 50 to 125A

MIG (FCAW) Welding Output @ 30% duty cycle

90A

MIG Welding Voltage Range 16.5 to 20.3V

No-Load Voltage 42V

Welding Capacity Up to 3/16 in.

Wire Feed Speed 80 to 235 in. per minute.

Welding Wire Diameter (Flux) 0.030 or 0.035 in.

Protection Class

IP21S

Generator Compatible Yes

Cooling Fan

INTRODUCTION

The 125A Inverter Flux Core Welder is ideal for small welding jobs with carbon

steel, stainless steel, cast iron, copper and nickel. Among its many features are

IGBT inverter technology, thermal overload protection and waveform control.

SAFETY

WARNING! Read and understand all instructions before using this tool. The

operator must follow basic precautions to reduce the risk of personal injury

and/or damage to the equipment.

Keep this manual for safety warnings, precautions, operating or inspection and

maintenance instructions.

125A Inverter Flux Core

Welder

V4.0 125A Inverter Flux Core Welder 8785099

Visit www.princessauto.com for more information 3

HAZARD DEFINITIONS

Please familiarize yourself with the hazard notices found in this manual. A notice

is an alert that there is a possibility of property damage, injury or death if certain

instructions are not followed.

DANGER! This notice indicates an immediate and specific hazard that will

result in severe personal injury or death if the proper precautions

are not taken.

WARNING! This notice indicates a specific hazard or unsafe practice that

could result in severe personal injury or death if the proper

precautions are not taken.

CAUTION! This notice indicates a potentially hazardous situation that may result

in minor or moderate injury if proper practices are not taken.

NOTICE! This notice indicates that a specific hazard or unsafe practice will

result in equipment or property damage, but not personal injury.

WORK AREA

1. Operate in a safe work environment. Keep your work area clean, well-lit and free

of distractions.

2. Remove all unnecessary people from the work area when welding. Anyone

remaining in the work area must wear the appropriate welding safety equipment.

3. Store tools properly in a safe and dry location. Keep tools out of the reach

of children.

4. Do not weld on damp surfaces that can transmit the electric current without

taking precautions for the welder and bystanders. The welding wire, welding

head and nozzle are electrically ‘hot’.

5. Do not install or use in the presence of flammable gases, dust or liquids.

6. Welding sparks and ejected molten slag can start a fire. Remove

combustible materials within 39 ft (12 metres) of the welding unit. See Fire

and Explosion Precautions.

7. Have a fire extinguisher readily available (see Fire and Explosion Precautions).

8. Use protective screens or barriers to protect others from flash and glare;

warn others in the area to look away from the arc.

8785099 125A Inverter Flux Core Welder V4.0

4 For technical questions call 1-800-665-8685

9. Keep the welding unit at least one foot from any wall or structure.

10. Check that the work area is free from fires, sparks or hot debris before leaving.

PERSONAL SAFETY

WARNING! Wear personal protective equipment approved by the Canadian

Standards Association (CSA) or American National Standards Institute (ANSI).

HEAD PROTECTION

DANGER! Never look directly at the welding arc without the proper protection.

The light can cause flash burn damage and impair vision. Although treatment is

possible, multiple occurrences can result in permanent eye damage.

1. Protect your eyes from welding light by wearing a welder's helmet fitted

with a filter shade suitable for the type of welding you are doing. The

welding process produces intense white light, infrared and ultraviolet light,

these arc rays can burn both eyes and skin.

a. Consult the Welding Shade Guide in Appendix A for the minimum shade

to protect the eyes based on the amperage and type of welding.

2. An opaque helmet will protect against the ultraviolet or infrared light. A

helmet will also protect against ejected hot material and slag. The helmet

should protect the face, forehead, ears and neck.

3. Wear a fire-resistant head covering like a skullcap or balaclava hood to

protect your head when the faceplate is down or when using a welding

hand-held face shield.

4. Wear ventilated safety goggles beneath the welding helmet or behind the

hand-held face shield. The cooling weld bead may fragment or eject slag

that can damage the eyes, when the helmet or hand-held face shield is not

in place.

a. Eye protection equipment should comply with CSA Z94.3-07 or ANSI

Z87.1 standards based on the type of work performed.

5. Wear fire resistant earplugs when welding overhead to prevent spatter or

slag from falling into ear.

V4.0 125A Inverter Flux Core Welder 8785099

Visit www.princessauto.com for more information 5

PROTECTIVE CLOTHING

1. Wear a leather apron or jacket, leather welding gloves and full foot protection.

Choose clothing fabrics that resist sparks, heat, flames and splashes of molten

material. Artificial fabrics may burn and melt, resulting in a more severe injury.

a. Wear welding capes and sleeves when performing overhead welding.

2. Do not wear clothes or protective gear that are frayed, oily or greasy as they

may ignite from the heat or ejected slag and sparks.

3. Wear thick clothes that do not expose the skin. Ultraviolet or infrared light

can burn skin with sufficient exposure.

4. Do not wear clothing that can hold hot debris or sparks such as pant cuffs,

shirt pockets or boots. Choose clothing that has flaps over pockets or wear

clothing to cover the openings such as pant legs over the boots or an apron

over the shirt.

5. Gloves shall should contain an insulating lining to protect against an electric

shock.

6. Rubber soled footwear or electrically insulated work boots are recommended

while working with a welding unit. The non- skid sole is will also help

maintain footing and balance during work.

a. Select boots with steel toe protection to prevent injury from falling

objects.

RESPIRATORS

1. Respiratory protection is needed when ventilation is not sufficient to

remove welding fumes or when there is risk of oxygen deficiency.

a. Wear a NIOSH approved respirator when working on materials that

produce dust or particulate matter.

2. Work in a confined space only if it is well ventilated or while wearing an air-

supplied respirator. Welding fumes and gases can displace air and lower the

oxygen level causing injury or death. Be sure the breathing air is safe (See

Fumes and Gases).

3. The user can take the additional precaution of informing another person in

the work area of the potential danger, so that person can watch for

indications that the user is suffering from oxygen deprivation.

8785099 125A Inverter Flux Core Welder V4.0

6 For technical questions call 1-800-665-8685

PERSONAL PRECAUTIONS

Control the tool, personal movement and the work environment to avoid

personal injury or damage to the tool.

1. Do not operate any tool when tired or under the influence of drugs, alcohol

or medications.

2. Avoid wearing clothes or jewelry that can become entangled with the

moving parts of a tool. Keep long hair covered or bound.

3. Remove all jewelry or metal items from your person before welding. Metal

items may connect to the welding unit’s electrical circuit, causing an injury

or death.

4. Do not overreach when operating the tool. Proper footing and balance enables

better control in unexpected situations.

5. Support the workpiece or clamp it to a stable platform. Holding the

workpiece by hand or against your body may lead to personal injury.

6. Do not wear any personal grooming products that are flammable, such as

hair preparations, perfume or cologne with an alcohol base.

7. Remove any combustibles, such as butane lighters or matches, from your

person before doing any welding. Hot welding sparks may light the matches

or ignite leaking lighter fuel.

SPECIFIC SAFETY PRECAUTIONS

WARNING! DO NOT let comfort or familiarity with product (gained from

repeated use) replace strict adherence to the tool safety rules. If you use

this tool unsafely or incorrectly, you can suffer serious personal injury.

Welding produces sparks, molten slag, intense white light, plus infrared and

ultraviolet light. A cooling bead can eject chips or fragments of slag. Any of

these can cause direct harm to the eyes and skin of the welder or bystanders.

1. Use the correct tool for the job. This tool was designed for a specific function.

Do not modify or alter this tool or use it for an unintended purpose.

2. Welding requires the use a hand-held face shield or helmets with full face

protection per CSA standard Z94.3.1.

3. Protect against reflected arc rays. The rays can reflect off a shiny surfaces

behind the user, into the helmet and off the filter lens into the eyes. Remove

V4.0 125A Inverter Flux Core Welder 8785099

Visit www.princessauto.com for more information 7

or cover any reflective surface behind the user such as a glossy painted

surface, aluminum, stainless steel or glass.

4. Welding produces sparks and molten slag. A cooling bead can eject chips

or fragments of slag. Any of these can cause direct harm to the eyes or skin

of the user or bystanders.

5. Erect protective screens or barriers to protect bystanders from the flash and

glare; warn others in the area not to watch the arc. Do not strike a welding

arc until all bystanders and you (the user) have welding shields and/or

helmets in place.

6. Immediately replace a cracked or broken helmet or a scratched or damaged

lens filter to avoid damage to the eyes or face from arc flash or ejected

molten material.

7. Do not handle hot metal or welding wire with bare hands. Handling may result in

a burn injury.

8. Do not use the welding unit if personal movement is confined or if there is a

danger of falling.

9. Keep all panels and covers securely in place when operating the welding unit.

10. Insulate the ground clamp when not connected to a workpiece to prevent

contact with any metal object.

11. Do not operate the welding unit if the MIG torch, welding cable or ground cable

are wet. Do not immerse them in water. These components and the welding

unit must be completely dry before attempting to use them.

12. Do not point the torch at any body part of yourself or at anyone else.

13. Do not use a welding unit to thaw frozen pipes.

14. Insulate yourself from the work and the ground using dry insulation.

Make certain that the insulation is large enough to cover your full area of

physical contact.

15. When not welding, make certain that no part of the welding circuit is touching

the workpiece or the ground. Accidental contact can cause overheating and

create a fire hazard.

16. Maintain good ventilation of the louvers on this equipment. Good ventilation

is of critical importance for the normal performance and service life of this

equipment.

8785099 125A Inverter Flux Core Welder V4.0

8 For technical questions call 1-800-665-8685

17. When working above floor level, use a safety belt to protect yourself from a

fall should you get a shock.

FIRE AND EXPLOSION PRECAUTIONS

Welding can produce sparks, hot slag or spatter, molten metal drops and hot

metal parts that can start fires.

1. Clear the floor and walls of an area of all combustible and/or flammable

materials up to 39 ft (12 metres) away from the welding unit. Hot debris

ejected during welding can land at a considerable distance away. Solid

floors of concrete or masonry is the preferred working surface.

a. Cover any combustible material with fire resistant covers or shields, if it

cannot be removed. The covering must be tight and should not leave

openings for sparks or ejected slag to enter.

b. Check both sides of a panel or wall for combustible material. Remove

the combustible material before welding.

2. A combustible floor should be protected with a fire resistant covering.

Alternatives are to spray the floor with water to keep it wet for the duration

of the welding or cover with damp sand. Care must also be taken to avoid

an electric shock when this is done. A combustible floor directly laid onto

concrete does not need to be sprayed with water.

3. Seal cracks and openings to adjacent areas that a spark or slag can enter.

Seal any openings found with a fire-resistant cover. Shut doors and windows

that do not provide ventilation or erect protective screens in front of them

when possible.

4. Avoid welding near hydraulic lines or containers containing flammable

contents.

5. Do not perform any welding work on containers that held flammable or

toxic substance, until they are cleaned by a person trained in removing toxic

and flammable substances and vapours per the American Welding Standard

AWS F4.1.

6. Open a container before performing any welding work on it. The heat

generated by the welding process will cause the air and gases to expand.

The internal pressure may cause a sealed or closed container to rupture,

possibly causing an injury or death.

V4.0 125A Inverter Flux Core Welder 8785099

Visit www.princessauto.com for more information 9

7. Do not weld pipes or metal that are covered in combustible material or in

contact with combustible structure such as a wall. Only weld if the covering

can be safely removed.

a. Follow all safety precautions and legal requirements before welding a

workpiece that contains Asbestos or attempting to remove the Asbestos

covering. This requires expert knowledge and equipment.

b. Molten slag can run down the inside and outside of a pipe and start a

fire. Be aware where the pipe terminates and take precautions.

8. Do not weld a panel that is a sandwich construction of combustible and

metal materials.

9. Have a fire extinguisher available for immediate use. A dry chemical fire

extinguisher for Types A, B and C is suggested.

a. Welding a combustible metal like zinc, magnesium or titanium requires

a Type D fire extinguisher.

b. Do not use liquid based fire extinguishing methods near the electric

welding unit, as it may cause a shock hazard.

10. Ventilation systems should be positioned so sparks or molten slag isn’t

carried to an adjacent area.

11. Have a Fire Watcher observing areas outside of the welder’s view, such as

the opposite side of a wall or behind the welder. A fire may also start on the

other side of a structure that could not be removed. The Fire Watcher will

extinguish a fire or raise the alarm to evacuate if the fire cannot be

contained by the extinguishing equipment.

a. A fire watch extends at least 30 minutes after the welding is complete to

ensure there are no fires caused by smoldering sparks or ejected

material.

FUMES AND GASES

WARNING! Stop welding and move to a location with ventilation if your eyes,

nose or throat become irritated. This indicates the ventilation is not adequate

to remove the fumes. Do not resume welding until the ventilation is improved

and the discomfort ceases. Seek medical attention if the symptoms do not

diminish or if the welder experiences nausea, dizziness or malaise.

8785099 125A Inverter Flux Core Welder V4.0

10 For technical questions call 1-800-665-8685

Welding may produce hazardous fumes and gas during the welding process. A well

ventilated work area can normally remove the fumes and gases, but sometimes the

welding produces fumes and gases that are hazardous to your health.

1. Only work in a confined space if the area is well ventilated or while wearing

a respirator or an air-supplied respirator. Welding fumes and gases can

displace air and lower the oxygen level causing injury or death. Be sure the

breathing air is safe. Always have a trained watchperson nearby.

a. If ventilation in the work area is poor, use an approved air-supplied

respirator. All the people in the work area must also have air-supplied

respirators.

b. Oxygen displacement can occur in confined areas when the shielding

gas fills the area and pushes out air. Argon, Propane and Carbon

Dioxide are heavier than air and will fill a confined space from the

bottom up.

2. Avoid positions that allow welding fumes to reach your face. Always attempt to

weld ‘upwind’ of the workpiece with the airflow across the face of the welder.

Airflow from behind may create a low pressure area in front of the welder and

draw the fumes to the person.

3. Ventilate the work area to remove welding fumes and gases. The fumes and

gases should be drawn away from the user.

a. Ventilation should be enough to disperse fumes, but not enough to

disturb the shielding gas or flame during welding.

b. Ventilation exhaust shall be directed to a non-work area to avoid

exposing other people to potential toxic or dangerous fumes.

c. Air removed from the work area by the ventilation system must be

replenished with fresh air to avoid oxygen starvation or a build-up of fumes

or gases. Only use air to provide ventilation. Any other combination of gases

may be explosive or toxic to people in the work area.

d. Ventilation methods that remove gas and fumes from the welding point

before they reach the welder’s face should be given preference.

4. Avoid welding in a work area that has vapours from cleaning, degreasing or any

spraying operations. The heat and light from welding can react with the vapour

and form irritating or potentially toxic gases. Wait for the vapours to disperse.

V4.0 125A Inverter Flux Core Welder 8785099

Visit www.princessauto.com for more information 11

5. Consult the manufacturer's Safety Data Sheets (SDS) for instructions and

precautions about metals, consumables, coatings, cleaners and degreasers.

a. Do not weld on coated metals such as galvanized, lead or cadmium

plated steel, unless the coating is removed from the weld area. The

coatings and any metals containing these elements can give off toxic

fumes during the welding process.

b. Do not weld, cut or heat lead, zinc, cadmium, mercury, beryllium or similar

metals without seeking professional advice and inspection of the welding

area’s ventilation. These metals produce extreme toxic fumes, which can

cause discomfort, illness and death.

c. Do not weld or cut near chlorinated solvents or in areas that chlorinates

solvents can enter. The heat or ultraviolet light of the arc can separate

chlorinated hydrocarbons into a toxic gas (phosgene) that can poison

or suffocate the user or bystanders.

6. Check the Safety Data Sheet for the proper handling and safety precautions

for consumable welding rods as the coating can have multiple chemicals.

POWER TOOL PRECAUTIONS

This equipment requires a dedicated 120 volt, 20 amp single-phase alternating

current circuit equipped with a similarly rated circuit breaker or slow blow fuse.

Do not run other appliances, lights, tools or equipment on the circuit while

operating this welding unit.

1. Do not drape or carry coiled welding cables on your body while the cables

are plugged into the welding unit.

2. Do not start the tool when the welding wire is touching the workpiece.

3. Hold the tool by the insulated gripping surfaces when performing an operation

where it may contact hidden wiring or its own cord and cables. Contact with a

‘live’ wire will electrify exposed metal parts and shock the operator.

4. Take work breaks to prevent the tool's motor from overheating and/or

overloading. Refer to the welding unit’s duty cycle in Specifications.

5. Keep hands away from the welding arc and the area it is being applied to

when the tool is in operation.

6. Do not connect the welding unit ground clamp to an electrical conduit. Do

not weld on an electrical conduit.

8785099 125A Inverter Flux Core Welder V4.0

12 For technical questions call 1-800-665-8685

7. Do not touch the welding wire or welded surface immediately after use. The

surface will be hot and may cause an injury.

ELECTRICAL SAFETY

1. Do not come into physical contact with the welding current circuit. The

welding current circuit includes:

a. The workpiece or any conductive material in contact with it.

b. The ground clamp.

c. The welding wire;

d. Any metal parts on the wire feed torch.

e. The output terminals.

2. The welding wire reel, welding head, nozzle and semiautomatic welding guns

are electrically ‘hot’ when the welding unit is in semiautomatic or automatic

wire welding mode.

3. Insulate yourself from the electrical current and ground using electrical

insulating mats or covers big enough to prevent physical contact with the

workpiece or ground.

4. Connect the ground clamp as close to the welding area on the workpiece as

practical to prevent welding current from traveling along an unexpected

path and causing an electric shock or fire hazard.

a. An option is to attach the ground clamp to a bare metal spot on a metal

workbench. The circuit will complete as long as the workpiece is also in

full contact with the bare metal workbench.

5. Only use insulated connectors to join welding cables.

6. Ensure there are no contacts between the workpiece and work area that

would allow it to ground, other than through the ground cable circuit

7. Do not exceed the duty cycle or amperage required for the type of welding.

Excessive amperage can cause the deterioration of protective insulation and

create a shock hazard.

8. Unplug the welding unit when not in use as the unit as current is still

entering the unit, even when it is turned off.

9. Frequently inspect input power cable for wear and tear, replace the cable

immediately if damaged. Bare wiring is dangerous and can kill.

V4.0 125A Inverter Flux Core Welder 8785099

Visit www.princessauto.com for more information 13

10. Do not use damaged, under sized or badly joined cables.

11. Do not disconnect the power cord in place of using the ON/OFF switch on

the tool. This will prevent an accidental startup when the power cord is

plugged into the power supply.

a. In the event of a power failure, turn off the machine as soon as the

power is interrupted. The possibility of accidental injury could occur, if

the power returns and the unit is not switched off.

12. Make certain the power source conforms to requirements of your equipment

(see Specifications).

POWER CORD

1. Insert the power cord plug directly to the power supply whenever possible.

Extension cords are not recommended for use with this welding unit.

a. When an extension cord is required, use a welding version that exceeds

the welding unit’s maximum power requirement.

2. Do not operate this tool if the power cord is frayed or damaged, as an electric

shock or surge may occur, resulting in personal injury or property damage.

a. Inspect the tool's power cord for cracks, fraying or other faults in the

insulation or plug before each use.

b. Discontinue use if a power cord feels more than comfortably warm

while operating the tool.

3. Keep all connections dry and off the ground to reduce the risk of electric

shock. Do not touch plug with wet hands.

4. Prevent damage to the power cord by observing the following:

a. Do not pull on the cord to disconnect the plug from an outlet.

b. Keep cord away from heat, oil, sharp edges or moving parts.

c. Place the electrical cord in a position that prevents it from contacting

the tool or workpiece. The cord should always stay behind the tool.

5. Make sure to locate the cord so that it is not stepped on, tripped over or

otherwise subject to damage or stress.

6. Do not wrap the cord around the tool, as sharp edges may cut insulation or

cause cracks if wound too tight. Gently coil cord and either hang on a hook

or fasten with a device to keep cord together during storage.

8785099 125A Inverter Flux Core Welder V4.0

14 For technical questions call 1-800-665-8685

LOW VOLTAGE

Low voltage may cause overheating due to higher power current being drawn to

the tool that will shorten the motor life.

An extension cord may cause a drop in power to the tool if it is too long or the

amperage rating is not correct. This may result in the following:

1. The tool will not activate when switched on.

2. The tool may switch on, but fails to maintain power when applied to

a workpiece.

3. The tool may overheat, possibly starting a fire.

Test the tool by plugging it directly to the power supply. If it powers on, change

the extension cord with to one with the correct rating and as short as needed.

You may need to position the workpiece closer to the power supply.

ELECTROMAGNETIC FIELDS

WARNING! Stop welding immediately and move away from the welding unit if

you feel faint, dizzy, nausea or shocks. Seek medical attention.

Electromagnetic Fields (EMF) can interfere with electronic devices such as

pacemakers. Anyone with a pacemaker should consult with their doctor before

working with or near a welding unit. The following steps can minimize the

effects of electromagnetic fields.

1. Twist or tape cables together and prevent coils.

2. Do not drape cables on your body.

3. Keep the welding power source and cables as far away from the user as

practical. A minimum of 24 in. is recommended.

4. Connect the workpiece clamp as close to the weld as possible, but lay the

MIG torch and workpiece cables away from the user.

5. Use the lowest current setting possible during welding.

6. Avoid long and regular bursts of energy while welding. Apply the welding

wire in short strokes and intermittently. This will prevent the pacemaker

from interpreting the signal as a rapid heartbeat.

7. Keep the lead cable and ground cables on the same side of your body.

8. Do not weld while carrying the welding power source.

9. Do not work next to, sit or lean on the welding power source.

V4.0 125A Inverter Flux Core Welder 8785099

Visit www.princessauto.com for more information 15

UNPACKING

WARNING! Do not operate the tool if any part is missing. Replace the

missing part before operating. Failure to do so could result in a malfunction

and personal injury.

Remove the parts and accessories from the packaging and inspect for damage.

Make sure that all items in the contents are included.

Contents: • Welding Machine • MIG Torch • Ground Lead with Clamp

• Brush/Hammer • Contact Tips

IDENTIFICATION KEY

A. Welding Machine

B. Voltage Selector Dial – Reduce or increase the voltage by turning the

voltage selector dial. Different materials and material thickness will require

different voltage settings. Refer to the Suggested Settings Chart on the

inside door of the welding unit.

C. Power Light – Illuminates when the electrical power is active.

Fig. 1

8785099 125A Inverter Flux Core Welder V4.0

16 For technical questions call 1-800-665-8685

D. Alarm Light – Illuminates when the welding machine overheats. Power

output will shut-off automatically, but the fan will continue to run until the

heat is dispersed.

E. Amperage/Wire Speed Dial – Increase the amperage and wire feed speed

by turning the dial. The number 1 is the slowest wire feed speed, 10 is the

highest. You will need to adjust or ‘tune in’ your wire speed for different

welding conditions (thickness of metals, metal type, wire size, etc.). When

the wire speed is properly ‘tuned-in’ the welding wire will melt into the

material you are welding as quickly as it is fed through the welding torch.

IMPORTANT! The wire will feed faster without an arc. When an arc is

being drawn, the wire speed will slow.

F. Ground Clamp – Attaching the ground clamp to your workpiece ‘completes’

the welding current circuit. You must attach the ground clamp to the metal

you are welding. A poor connection at the ground clamp will waste power

and heat. Scrape away dirt, rust, scale, oil or paint from the clamping

surface before attaching the ground clamp.

G. Welding Cable and Torch – The welding wire is fed through the welding cable

and welding torch when the welding torch trigger is pulled. You will need to

install a contact tip and welding nozzle to the end of the welding torch.

BACK PANEL

H. Power Switch – This switch turns the welding unit ON and OFF. Make sure

the power switch is in the OFF position before performing any maintenance

on the welding unit.

I. Power Cord – This is a standard power cord.

ASSEMBLY & INSTALLATION

Numbered references in parenthesis (#1) refer to the included Parts List. Letter

references in parenthesis (A) refer to the included Identification Key. Dashed

numbers in parenthesis (Fig. 1-1) refer to a specific point in an illustration or image.

V4.0 125A Inverter Flux Core Welder 8785099

Visit www.princessauto.com for more information 17

POWER REQUIREMENTS

NOTICE! Do not operate this welding unit if the actual power source voltage

is less than 105 volts AC or greater than 132 volts AC. Improper performance

and/or damage to the welding unit will result if operated on inadequate or

excessive power.

This welding unit is designed to operate on a properly grounded 120 volt, 60

Hz, single-phase alternating current (AC) power source that has a 20 amp time

delayed fuse or circuit breaker. The use of the proper circuit size can eliminate

nuisance circuit breaker tripping when welding.

A qualified electrician should verify the actual voltage of the power outlet,

confirm the outlet is grounded and that the fuse is properly installed.

SHIELDING GAS

Shielding gas protects the exposed weld. The flux core in the welding wire

becomes a gas that expands to cover the molten metal, preventing impurities in

the air from contacting and weakening the weld.

The most common flux is 75% Argon and 25% Carbon Dioxide. There are other

flux mixes available based on the welding task.

ALIGN AND SET THE DRIVE ROLLER

The correct drive roller grove must be set on the wire drive mechanism before

the welding wire is installed in the unit.

1. Open the door to the welding unit’s drive compartment.

2. Remove the drive tension by loosening the drive tension adjusting knob

(Fig. 2-1) and lifting the drive tension adjustor away from the drive tension

arm (Fig. 2-2). Pull the drive tension arm away from the drive roller.

3. If there is a wire already installed in the welding unit, roll it back onto the

wire spool by hand-turning the spool counterclockwise. Be careful not to

allow the wire to come out of the rear end of the inlet guide tube (Fig. 2-3)

without holding onto it or it will unspool itself. Put the end of the wire into

the hole on the outside edge of the wire spool and bend it over to hold the

wire in place. Remove the spool of wire from the drive compartment of the

welding unit.

8785099 125A Inverter Flux Core Welder V4.0

18 For technical questions call 1-800-665-8685

4. Rotate the drive roller Cap (Fig. 2-4) counterclockwise and remove it from

the drive roller.

5. Pull the drive roller off of the drive roller shaft.

DRIVE ROLLER ADJUSTMENTS

The drive roller has two knurled grooves

built into it for different wire sizes. The

correct wire size number is stamped on

each side of the drive roller. The number

facing you when installing the drive

roller must match the wire size. Use only the proper size drive roller when using

your welding unit. Table 1 indicates which drive roller groove should be used

with each wire diameter size.

1. Find the side of the drive roller (Fig. 3-1) that is

stamped with the same wire diameter (Fig. 3-2)

as that of the wire being installed. Push the

drive roller onto the drive roller motor shaft

(Fig. 3-3), with the side stamped with the

desired wire diameter facing you.

2. Reinstall the drive roller cap (Fig. 2-4) and lock

in place by turning it clockwise.

3. Close the door to the welding unit drive compartment.

Any spool of wire that is oxidized should be discarded. Check if only the

exposed top layer of wire is oxidized by unspooling and checking the next layer.

Wire Diameter Drive Roller Groove

0.030 in. 0.8

0.035 in. 0.9

Table 1

Fig. 3

Fig. 2

V4.0 125A Inverter Flux Core Welder 8785099

Visit www.princessauto.com for more information 19

INSTALL THE WELDING WIRE

WARNING! Electric shock can kill! Always turn the power switch OFF and unplug

the power cord from the power source before installing the welding wire.

Remove old wire from the torch assembly before installing new welding wire. This

will help to prevent the possibility of the wire jamming inside the torch liner.

1. Remove the nozzle and contact tip from the end of the torch assembly.

a. Check that the power is OFF and the power cord unplugged before

removing the welding nozzle. The contact tip on this welding unit is

electrically hot whenever the torch trigger is pulled.

2. Make sure the proper groove on the

drive roller is in place for the installed

wire. Change the drive roller if the

proper grove is not in place (see Align

and Set the Drive Roller).

3. Find the leading end of the wire. Do not

unhook it. The leading end goes

through a hole in the outer edge of the

spool and is bent over the spool edge to

prevent the wire from unspooling.

4. Place the spool on the spindle so the wire is straight, not at an angle, when it

enters the welding unit mechanism (Fig. 4). The welding wire should always

come off the top of the spool into the drive mechanism.

5. The purpose of the drive brake is to halt the spool of wire at

nearly the same moment that wire feeding stops.

a. Four Inch Wire Spool - Install the drive brake hardware on

the top of the spool of wire as shown in Fig. 5.

6. Set the spool tension. Too much tension and the wire will slide

on the drive roller or the wire won’t feed into the mechanism.

Too little tension and the wire may unspool itself. Readjust the

drive brake tension to correct for either problem.

a. Turn the wire spool with one hand and while adjusting

the tension with the other hand.

b. Tighten (turn clockwise) the drive tension adjustment

knob with your free hand.

Fig. 5

Fig. 4

8785099 125A Inverter Flux Core Welder V4.0

20 For technical questions call 1-800-665-8685

c. Stop tightening when drag is felt on the wire spool that you are turning.

d. The wire spool is ready for use.

7. Free the leading end of the wire from the spool and use wire cutters to

remove the bent portion, leaving a straight 90° cut. Do not let go of the

welding wire while doing this, as the wire may unspool itself.

8. Loosen the tension adjusting knob holding the drive tension arm in place

and lift the tension arm away from the driver roller.

9. Insert the leading end of the wire into the inlet guide tube. Then push the

wire across the drive roller and insert six inches into the torch assembly.

a. Make certain that the welding wire is actually going into the torch liner

and not alongside it. A misaligned wire may be deflected in another

direction and could damage the internal mechanisms.

10. Line the wire in the drive roller groove, then place the drive tension arm on

the drive roller.

11. Flip the quick release drive tensioner back up into position on the drive

tensioner arm.

12. Tighten (turn clockwise) the drive tension adjusting knob until the tension

roller is applying enough force on the wire to prevent it from slipping out of

the drive assembly.

13. Let go of the wire.

14. Connect the welding unit power cord to the power source.

15. Turn the welding unit ON.

16. Set the voltage switch to the voltage (heat) setting recommended for the

gauge metal that is to be welded. Refer to the label mounted on the cover,

inside the drive compartment, for recommended voltage (heat) settings for

your welding job.

17. Set the wire speed control to the middle of the wire speed range.

18. Straighten the torch cable and pull the trigger on the welding torch to feed

the wire through the torch assembly.

19. When at least an inch of wire sticks out past the end of the torch, release

the trigger.

20. Turn the power switch to the OFF position.

La page charge ...

Power Fist 8785099 Le manuel du propriétaire

Power Fist 8785099 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents