Samsung HP-T4254 Manuel utilisateur

Catégorie
Téléviseurs à écran plasma
Taper
Manuel utilisateur

Ce manuel convient également à

PLASMA DISPLAY
HP-T4254
HP-T5054
Owners
Instructions
Register your product at www.samsung.com/global/register
Record your Model and Serial number here for future reference.
▪ Model _______________ ▪ Serial No. _______________
BN68-01192F-02Eng-1.indd 1 2007-03-23 ソタネト 3:10:05
English - 2
Important Warranty Information Regarding Television Format Viewing
Wide screen format PDP Displays (16:9, the aspect ratio of the screen width to height) are primarily designed to view wide
screen format full-motion video. The images displayed on them should primarily be in the wide screen 16:9 ratio format,
or expanded to fill the screen if your model offers this feature and the images are constantly moving. Displaying stationary
graphics and images on screen, such as the dark side-bars on nonexpanded standard format television video and
programming, should be limited to no more than 5% of the total television viewing per week.
Additionally, viewing other stationary images and text such as stock market reports, video game displays, station logos,
web sites or computer graphics and patterns, should be limited as described above for all televisions. Displaying stationary
images that exceed the above guidelines can cause uneven aging of PDP Displays that leave subtle, but permanent
burned-in ghost images in the PDP picture. To avoid this, vary the programming and images, and primarily display
full screen moving images, not stationary patterns or dark bars.
On PDP models that offer picture sizing features, use these controls to view different formats as a full screen picture.
Be careful in the selection and duration of television formats used for viewing. Uneven PDP aging as a result of format
selection and use, as well as burned-in images, are not covered by your Samsung limited warranty.
© 2007 Samsung Electronics Co., Ltd. All rights reserved.
U.S.A Only
The product unit accompanying this user manual is licensed under certain intellectual property rights of certain
third parties. In particular, this product is licensed under the following US patents: 5,991,715, 5,740,317, 4,972,484,
5,214,678, 5,323,396, 5,539,829, 5,606,618, 5,530,655, 5,777,992, 6,289,308, 5,610,985, 5,481,643, 5,544,247,
5,960,037, 6,023,490, 5,878,080, and under US Published Patent Application No. 2001-44713-A1.
This license is limited to private non-commercial use by end-user consumers for licensed contents. No rights are
granted for commercial use. The license does not cover any product unit other than this product unit and the license
does not extend to any unlicensed product unit or process conforming to ISO/IEC 11172-3 or ISO/IEC 13818-3 used or
sold in combination with this product unit. The license only covers the use of this product unit to encode and/or decode
audio files conforming to the ISO/IEC 11172-3 or ISO/IEC 13818-3. No rights are granted under this license for product
features or functions that do not conform to the ISO/IEC 11172-3 or ISO/IEC 13818-3.
Other countries
The product unit accompanying this user manual is licensed under certain intellectual property rights of certain third
parties. This license is limited to private non-commercial use by end-user consumers for licensed contents. No rights
are granted for commercial use. The license does not cover any product unit other than this product unit and the license
does not extend to any unlicensed product unit or process conforming to ISO/IEC 11172-3 or ISO/IEC 13818-3 used or
sold in combination with this product unit. The license only covers the use of this product unit to encode and/or decode
audio files conforming to the ISO/IEC 11172-3 or ISO/IEC 13818-3. No rights are granted under this license for product
features or functions that do not conform to the ISO/IEC 11172-3 or ISO/IEC 13818-3.
BN68-01192F-02Eng-1.indd 2 2007-03-23 ソタネト 3:10:05
English - 3
User Instructions
Screen Image retention
Do not display a still image (such as on a video game) on the plasma display panel for more than several minutes as it can
cause screen image retention. This image retention is also known as “screen burn”. To avoid such image retention, refer to
page 26 of this manual to reduce the degree of brightness and contrast of the screen when displaying a still image.
Altitude
The PDP can only operate normally at heights under 6500ft.
Heat on the top of the PDP TV
The top side of the product may be hot after long periods of use as heat dissipates from the panel through the vent hole in
the upper part of the product.
This is normal and does not indicate any defect or operation failure of the product.
However, children should be prevented from touching the upper part of the product.
The product is making a ‘cracking’ noise.
A ‘cracking’ noise may occur when the product contracts or expands due to a change of surrounding environment such as
temperature or humidity. This is normal and not a defect of the unit.
Cell Defects
The PDP uses a panel consisting of 1,230,000(SD-level) to 3,150,000(HD-level) pixels which require sophisticated
technology to produce. However, there may be a few bright or dark pixels on the screen. These pixels will have no impact
on the performance of the product.
Avoid operating the TV at temperatures below 5°C (41°F)
A still image displayed too long may cause permanent damage to the PDP Panel.
Watching the PDP TV in 4:3 format for a long period of time may leave traces of borders displayed on
the left, right and center of the screen caused by the difference of light emission on the screen.
Playing a DVD or a game console may cause similar effect to the screen.
Damages caused by the above effect are not covered by the Warranty.
Afterimage on the Screen.
Displaying still images from Video games and PC for longer than a certain period of time may produce partial after-images.
To prevent this effect, reduce the ‘brightness’ and ‘contrast’ when displaying still images for a long time.
Warranty
Warranty does not cover any damage caused by image retention.
Burn-in is not covered by the warranty.
BN68-01192F-02Eng-1.indd 3 2007-03-23 ソタネト 3:10:05
English - 4
Symbols
Press
One-Touch
Button
Note
Contents
GENERAL INFORMATION
■ List of Features ..............................................................5
Accessories ....................................................................
5
Viewing the Control Panel .............................................
6
Viewing the Connection Panel .......................................
7
Remote Control ..............................................................8
Installing Batteries in the Remote Control .....................9
CONNECTIONS
■ Connecting VHF and UHF Antennas .............................9
■ Connecting Cable TV ...................................................
10
■ Connecting a VCR ....................................................... 11
■ Connecting an S-VHS VCR ......................................... 11
■ Connecting a Camcorder .............................................12
■ Connecting a DVD Player/Set-Top Box .......................
12
■ Connecting a DVD Player/Set-Top Box via HDMI .......
13
■ Connecting a DVD Player/Set-Top Box via DVI ...........
13
■ Connecting a Digital Audio System ..............................
14
■ Connecting an Amplifier/DVD Home Theater ..............
14
■ Connecting a PC ..........................................................14
OPERATION
■ Turning the TV On and Off ...........................................15
■ Plug & Play Feature .....................................................15
■ Changing Channels .....................................................17
Adjusting the Volume ...................................................
18
■ Viewing the Display .....................................................
18
■ Viewing the Menus ......................................................
18
■ Memorizing the Channels ............................................19
■ Setting Up Your Remote Control ..................................
20
■ To Select the Source ....................................................
25
■ To Edit the I
nput Source Name ....................................25
PICTURE CONTROL
■ Using Automatic Picture Settings .................................26
■ Digital Noise Reduction ...............................................27
■ Changing the Screen Size ...........................................28
■ Configuring Detailed Settings on the Picture ...............
29
Active Color ..................................................................
30
■ DNIe (Digital Natural Image engine) ............................30
■ Selecting the Film Mode ..............................................31
■ Setting the Blue Screen Mode .....................................31
■ Setting the HDMI Black Level ......................................31
■ Viewing Picture-in-Picture ............................................
32
■ Freezing the Current Picture ........................................33
SOUND CONTROL
■ Using Automatic Sound Settings .................................34
■ Customizing the Sound ................................................34
■ Setting the TruSurround XT .........................................
35
Choosing a Multi-Channel Sound (MTS) Track - Digital
.. 35
Choosing a Multi-Channel Sound (MTS) Track - Analog
.. 36
Automatic Volume Control ...........................................
36
■ Selecting the Internal Mute ..........................................36
Adjusting the Melody Sound ........................................
37
■ Listening to the Sound of the Sub (PIP) Picture ..........37
CHANNEL CONTROL
■ Selecting the Antenna .................................................. 38
Adding and Erasing Channels .....................................
38
■ Setting Your Favorite Channels ...................................
39
■ Viewing the Channel Lists ...........................................
40
■ Setting the Default Channel List Mode ........................ 40
■ Labeling Channels ....................................................... 41
■ Fine Tuning Analog Channels ......................................
41
■ Checking the Digital-Signal Strength ........................... 42
■ LNA (Low Noise Amplifier) ...........................................
42
PC DISPLAY
■ Using Your TV as a Computer (PC) Display ................ 43
■ Display Modes ............................................................ 43
■ Setting up the TV with your PC .................................... 44
■ Setting the Home Theater PC ......................................
45
TIME SETTING
■ Setting the Time ........................................................... 46
FUNCTION DESCRIPTION
■ Selecting a Menu Language ........................................ 49
■ Using the Game Mode ................................................. 49
Viewing Closed Captions (On-Screen Text Messages) - Digital
....
50
Viewing Closed Captions (On-Screen Text Messages) - Analog
.. 51
■ Menu Transparency Level ...........................................
52
■ Setting the Light Effect .................................................
52
■ Using the Energy Saving Feature ................................ 53
■ Preventing Screen Burn-in ........................................... 53
■ Reducing the Effects of Screen Burn ...........................
54
■ Setting the Function Help ............................................ 54
■ Wall- mount adjustment (Sold separately) ...................
55
■ Upgrading the Software ............................................... 56
■ Using the V-Chip .......................................................... 56
About Anynet
+
■ What is Anynet
+
? ......................................................... 62
■ Connecting Anynet+ Devices .......................................
62
■ Setting Up Anynet+ ......................................................
63
■ Scanning and Switching between Anynet+ Devices ....
63
■ Recording .................................................................... 64
■ Listening through a Receiver ....................................... 65
■ Check Points before Requesting Service .................... 65
APPENDIX
■ Troubleshooting ........................................................... 66
■ Installing the Wall Mount Kit .........................................
67
■ How to assemble the Stand-Base
(depending on the model) ........................................... 68
■ Specifications ...............................................................
68
■ Dimensions (HP-T4254) .............................................. 69
■ Dimensions (HP-T5054) .............................................. 70
BN68-01192F-02Eng-1.indd 4 2007-03-23 ソタネト 3:10:06
English - 5
General Information
List of Features
Adjustable picture settings that can be stored in the TV’s memory.
Automatic timer to turn the TV on and off.
A special sleep timer.
V-Chip function.
Excellent Digital Interface & Networking :
With a built-in HD digital tuner, non-subscription HD broadcasts can be viewed with no Set-Top Box needed.
Remote Control
The supplied remote can be used to operate the TV as well as most DVD players, Set-top boxes, Cable Boxes and VCRs.
Excellent Picture Quality
- DNIe technology provides life-like clear images.
SRS TruSurround XT
- SRS TruSurround XT provides a virtual Dolby surround system.
Accessories
Please make sure the following items are included with your TV. If any items are missing, contact your dealer.
RETURN
FAV.CH
Remote Control
(BN59-00599A) /
AAA Batteries
(4301-000103)
Power Cord
(3903-000144)
Owner’s Instructions /
Quick Setup Guide
Warranty Card /
Registration Card /
Safety Guide Manual
Cloth-Clean
Cover-Bottom /
Screws (2ea)
(Refer to page 68)
Ferrite Core for
Power Cord
(3301-001110)
Ferrite Core for
Side-AV / S-VIDEO
(3301-001305 )
Ferrite Core for
Headphone
(3301-001456)
The following parts are sold separately and are available at most electronics stores.
S-VIDEO Cable (BN39-00149A) HDMI Cable (BN39-00641A) HDMI/DVI cable (BN39-00643A) Component Cables (RCA)
(BN39-00279A)
PC Cable (BN39-00115A) PC Audio Cable (BN39-00061B) Optical Cable Antenna Cable (BN39-00333A)
Ferrite Core (Power Cord, Audio/Video Cable,
S-Video Cable, Headphone)
The ferrite cores are used to shield the cables from interference.
When connecting a cable, open the ferrite core and clip it around
the cable near the plug.
BN68-01192F-02Eng-1.indd 5 2007-03-23 ソタネト 3:10:11
English - 6
Viewing the Control Panel
Buttons on the Lower-Right Part of the Panel
The buttons on the lower-right panel control your TV’s basic features, including the on-screen menu.
To use the more advanced features, you must use the remote control.
1
SOURCE
Toggles between all the available input sources
(TV, AV1, AV2, S-Video1, S-Video2, Component1,
Component2, PC, HDMI1, HDMI2, or HDMI3).
2
MENU
Press to see an on-screen menu of your TV’s features.
3
+ VOL –
Press to increase or decrease the volume. In the on-
screen menu, use the + VOL
buttons as you would
use the and buttons on the remote control.
4
CH
Press to change channels.
In the on-screen menu, use the CH buttons as
you would use the and buttons on the remote
control.
5
(ENTER)
Press to confirm a selection.
6
POWER
Press to turn the TV on and off.
Power Indicator
Blinks and turns off when the power is on and lights up
in stand-by mode.
Remote Control Sensor
Aim the remote control towards this spot on the TV.
7
Speakers
The product color and shape may vary depending on the model.
BN68-01192F-02Eng-1.indd 6 2007-03-23 ソタネト 3:10:15
English - 7
Viewing the Connection Panel
Rear Panel Jacks
Use the rear panel jacks to connect A/V components that will be connected continuously, such as VCR or DVD players. For
more information on connecting equipment, see pages 9-14. The product color and shape may vary depending on the model.
1
POWER IN
Connect the supplied power cord.
2
DIGITAL AUDIO OUT (OPTICAL)
Connect to a Digital Audio component.
3
AUDIO OUT (R/L)
Audio outputs to external devices.
4
PC AUDIO IN
Connect to the audio output jack on your PC.
5
PC IN
Connect to the video output jack on your PC.
6
DVI IN (HDMI 1) (AUDIO-R/L)
Connect to the DVI audio output jack of an external device.
7
HDMI IN 1, 2
Connect to the HDMI jack of a device with HDMI output.
(Only HDMI 1 can support HDMI-DVI IN and PC.)
This input can also be used as a DVI connection with
separate analog audio inputs. An optional HDMI/DVI
cable will be necessary to make this connection.
When using an optional HDMI/DVI adapter, the DVI analog
audio inputs on your TV allow you to receive left and right
audio from your DVI device. (Not compatible with PC)
8
ANT 1 IN(AIR)/ANT 2 IN(CABLE)
75Ω Coaxial connector for Air/Cable Network.
9
EX-LINK
Connect this to the jack on the optional wall mount
bracket. This will allow you to adjust the TV viewing
angle using your remote control.
0
AUDIO-R/L (AV IN 1)
Audio inputs for external devices, such as a camcorder
or VCR.
!
S-VIDEO (AV IN 1)
S-Video input for external devices with an S-Video
output, such as a camcorder or VCR.
@
VIDEO (AV IN 1)
Video input for external devices, such as a camcorder
or VCR.
#
COMPONENT IN 1, 2
Component video (Y/PB/PR) and audio (R-AUDIO-L) inputs.
Side Panel Jacks
Use the right side panel jacks to connect a component that is used only occasionally, such as a camcorder or video game.
The product color and shape may vary depending on the model.
1
HDMI IN 3
Connect to the HDMI jack of a device with HDMI output.
2
SERVICE
For service only.
3
S-VIDEO IN 2
S-Video input for external devices with an S-Video output.
4
AV IN 2
Video and audio inputs for external devices.
5
HEADPHONE
You can connect a set of headphones if you wish to watch a television program without
disturbing other people in the room.

BN68-01192F-02Eng-1.indd 7 2007-03-23 ソタネト 3:10:16
English - 8
Remote Control
You can use the remote control up to a distance of about 23 feet from the TV. When using the remote, always
point it directly at the TV. You can also use your remote control to operate your VCR, Cable box, DVD player,
or Set-Top Box.
1
POWER
Turns the TV on and off.
2
NUMERIC BUTTONS
Press to directly select a channel.
3
Press to select additional channels
(digital and analog) being broadcast
by the same station. For example,
to select channel “54-3”, press “54”,
then press “–” and “3”.
4
CH LIST
Used to display Channel Lists on the
screen.
5
ANTENNA
Press to select “AIR” or “CABLE”.
6
VCR/DVD Functions
- Rewind
- Stop
- Play/Pause
- Fast/Forward
7
+ VOL
Press to increase or decrease the
volume.
8
MUTE
Press to temporarily cut off the
sound.
9
MENU
Displays the main on-screen menu.
0
S.MODE
Press to select the sound mode.
!
RETURN
Returns to the previous menu.
@
P.MODE
Press to select the picture mode.
#
CAPTION
Controls the caption decoder.
$
FAV.CH
Press to switch to your favorite
channels.
%
SLEEP
Press to select a preset time interval
for automatic shut off.
^
SRS
Selects SRS TruSurround XT mode.
&
SET
Sets the remote to control your TV,
VCR, Cable, DVD, or Set-Top Box.
*
TV/DVD/STB/CABLE/VCR
Press to operate your TV, DVD, STB,
CABLE (box), or VCR.
(
Press to backlight the VOL, CH,
and active source button (TV, DVD,
CABLE, STB, VCR) on the remote.
)
SOURCE
Press to display all of the available
video sources.
a
PRE-CH
Tunes to the previous channel.
b
WISELINK
Not available.
c
REC
This remote can be used to control
recording on Samsung recorders.
(Refer to page 64)
d
CH
Press to change channels.
e
EXIT
Press to exit the menu.
f
UP▲/DOWN▼/LEFT◄/
RIGHT►/ENTER
Use to select on-screen menu items
and change menu values.
g
INFO
Press to display information on the
TV screen.
h
Anynet+
Runs the Anynet+ view functions and
sets up Anynet+ devices.
i
STILL
Press to stop the action during a
particular scene. Press again to
resume normal video.
j
P.SIZE
Press to change the screen size.
k
PIP
Picture-in Picture ON/OFF.
l
CH /
Displays the available channels in
sequence. (These buttons change
channels in the PIP window only.)
m
MTS
Press to choose stereo, mono or
Separate Audio Program (SAP
broadcast).
n
RESET
When your remote does not work,
change the batteries and press
the RESET button for 2-3 seconds
before use.
This is a special remote control for
the visually impaired, and has Braille
points on the POWER, Channel,
Volume, STOP, and PLAY/PAUSE
buttons.
The performance of the remote control
may be affected by bright light.
RETURN
FAV.CH
BN68-01192F-02Eng-1.indd 8 2007-03-23 ソタネト 3:10:17
English - 9
Connections
Connecting VHF and UHF Antennas
If your antenna has a set of leads that look like this, see “Antennas with 300 Ω Flat Twin
Leads” below.
If your antenna has one lead that looks like this, see “Antennas with 75 Ω Round Leads”.
If you have two antennas, see “Separate VHF and UHF Antennas”.
Antennas with 300 Ω Flat Twin Leads
If you are using an off-air antenna (such as a roof antenna or “rabbit ears”) that has 300
twin flat leads, follow the directions below.
1 Place the wires from the twin leads under the screws on a 300-75 Ω adapter (not supplied).
Use a screwdriver to tighten the screws.
2 Plug the adaptor into the ANT 1 IN (AIR) or ANT 2 IN (CABLE) terminal on the back of the TV.
Antennas with 75 Ω Round Leads
1
Plug the antenna lead into the ANT 1 IN (AIR) or ANT 2 IN (CABLE) terminal on the back of the TV.
Separate VHF and UHF Antennas
If you have two separate antennas for your TV (one VHF and one UHF), you must combine
the two antenna signals before connecting the antennas to the TV. This procedure requires
an optional combiner-adaptor (available at most electronics shops).
1 Connect both antenna leads to the combiner.
2 Plug the combiner into the ANT 1 IN (AIR) or ANT 2 IN (CABLE) terminal on the bottom of the
back panel.
ANT 1 IN (AIR)
ANT 1 IN (AIR)
UHF
VHF
ANT 1 IN (AIR)
UHF
VHF
Installing Batteries in the Remote Control
1 Lift the cover at the back of the remote control upward as shown in the figure.
2 Install two AAA size batteries.
Make sure to match the “+” and “–” ends of the batteries with the diagram inside the
compartment.
Do not mix battery types, i.e. alkaline and manganese.
3 Close the cover as shown in the figure.
Remove the batteries and store them in a cool, dry place if you won’t be using the
remote control for a long time. The remote control can be used up to about 23 feet
(7m) from the TV. (Assuming typical TV usage, the batteries last for about one year.)
If the remote control doesn’t work, check the following:
1. Is the TV power on?
2. Are the plus and minus ends of the batteries reversed?
3. Are the batteries drained?
4. Is there a power cut, or is the power cord unplugged?
5. Is there a special fluorescent light or a neon sign nearby?
BN68-01192F-02Eng-1.indd 9 2007-03-23 ソタネト 3:10:19
English - 10
ANT OUT
ANT IN
ANT 2 IN (CABLE)
ANT 2 IN (CABLE)
Connecting Cable TV
To connect to a cable TV system, follow the instructions below.
Cable without a Cable Box
1 Plug the incoming cable into the ANT 2 IN(CABLE) terminal on the back of the TV.
Because this TV is cable-ready, you do not need a cable box to view
unscrambled cable channels.
1 Find the cable that is connected to the ANT OUT terminal on your cable box.
This terminal might be labeled “ANT OUT”, “VHF OUT” or simply, “OUT”.
2 Connect the other end of this cable to the ANT 2 IN(CABLE) terminal on the back of
the TV.
Connecting to a Cable Box that Descrambles All Channels
Connecting to a Cable Box that Descrambles Some Channels
If your cable box descrambles only some channels (such as premium channels), follow the instructions below.
You will need a two-way splitter, an RF (A/B) switch, and four lengths of Antenna cable. (These items are available
at most electronics stores.)
1 Find and disconnect the cable that is
connected to the ANT IN terminal on your
cable box.
This terminal might be labeled “ANT IN”,
“VHF IN” or simply, “IN”.
2 Connect this cable to a two-way splitter.
3 Connect an Antenna cable between an
OUTPUT terminal on the splitter and the IN
terminal on the cable box.
4 Connect an Antenna cable between the
ANT OUT terminal on the cable box and the
B–IN terminal on the RF(A/B) switch.
5 Connect another cable between the other
OUT terminal on the splitter and the A–IN
terminal on the RF (A/B) switch.
6 Connect the last Antenna cable between
the OUT terminal on the RF (A/B) switch
and the ANT 2 IN (CABLE) terminal on the
rear of the TV.
After you have made this connection, set the A/B switch to the “A” position for normal viewing. Set the A/B switch to the “B”
position to view scrambled channels. (When you set the A/B switch to “B”, you will need to tune your TV to the cable box’s
output channel, which is usually channel 3 or 4.)
Splitter
Cable Box
RF (A/B)
Switch
Incoming
cable
Splitter
Incoming
cable
Splitter
Cable Box
Incoming
cable
Splitter
Incoming
cable
TV Rear
RF (A/B)
Switch
ANT 2 IN (CABLE)
ANT IN
Splitter
Incoming
cable
RF (A/B)
Switch
Cable Box
BN68-01192F-02Eng-1.indd 10 2007-03-23 ソタネト 3:10:21
English - 11
S-Video Connection
Your Samsung TV can be connected to the S-Video jack of a VCR.
(This connection delivers a better picture when compared to the regular Video connection above.)
Connecting a VCR
Video Connection
These instructions assume that you have already connected your TV to an antenna or a cable TV system (according
to the instructions on pages 9~10). Skip step 1 if you have not yet connected to an antenna or a cable system.
1 Unplug the cable or antenna
from the back of the TV.
2 Connect the cable or antenna
to the ANT IN terminal on the
back of the VCR.
3 Connect an Antenna Cable
between the ANT OUT
terminal on the VCR and the
ANT 1 IN(AIR) or ANT 2 IN
(CABLE) terminal on the TV.
4 Connect a Video Cable
between the VIDEO OUT
jack on the VCR and the AV
IN 1 [VIDEO] jack on the TV.
5 Connect Audio Cables
between the AUDIO OUT
jacks on the VCR and the AV
IN 1 [R-AUDIO-L] jacks on
the TV.
If you have a “mono”
(non-stereo) VCR, use a Y-
connector (not supplied) to
hook up to the right and left
audio input jacks of the TV.
If your VCR is stereo, you
must connect two cables.
Each VCR has a different back panel configuration.
When connecting a VCR, match the color of the connection terminal to the cable.
VCR Rear Panel
TV Rear Panel
2
Audio Cable(Not supplied)5
Video Cable(Not supplied)4
Antenna cable(Not supplied)3
1 To begin, follow steps 1–3
in the previous section to
connect the antenna or cable
to your VCR and your TV.
2 Connect an S-Video Cable
between the S-VIDEO OUT
jack on the VCR and the AV
IN 1 [S-VIDEO] jack on the
TV.
3 Connect Audio Cables
between the AUDIO OUT
jacks on the VCR and the AV
IN 1 [R-AUDIO-L] jacks on
the TV.
An S-Video may be included with your VCR. (If not, check your local electronics store.)
Each VCR has a different back panel configuration.
When connecting a VCR, match the color of the connection terminal to the cable.
VCR Rear Panel
TV Rear Panel
Audio Cable (Not supplied)
3
S-Video Cable(Not supplied)2
Antenna cable(Not supplied)3
BN68-01192F-02Eng-1.indd 11 2007-03-23 ソタネト 3:10:24
English - 12
Connecting a Camcorder
The side panel jacks on your TV make it easy to connect a camcorder to your TV.
They allow you to view the camcorder tapes without using a VCR
1 Connect a Video Cable
(or S-Video Cable) between
the AV IN 2 [VIDEO]
(or S-VIDEO) jack on the TV
and the VIDEO OUT jack on
the Camcorder.
2 Connect Audio Cables
between the AV IN 2
[L-AUDIO-R] jacks on the TV
and the AUDIO OUT jacks on
the Camcorder.
Each Camcorder has a different back panel configuration.
When connecting a Camcorder, match the color of the connection terminal to the cable
.
Connecting a DVD Player/Set-Top Box
The rear panel jacks on your TV make it easy to connect a DVD Player/Set-Top Box to your TV.
1 Connect Component Cables
between the COMPONENT
IN 1 [Y, P
B, PR] (or
COMPONENT IN 2 [Y, P
B,
PR]) jacks on the TV and the
COMPONENT OUT [Y, P
B,
PR] jacks on the DVD Player/
Set-Top Box.
2 Connect Audio Cables
between the COMPONENT
IN 1 [R-AUDIO-L](or
COMPONENT IN 2
[R-AUDIO-L]) jacks on the TV
and the AUDIO OUT jacks on
the DVD Player/Set-Top Box.
Component video separates the video into Y (Luminance (brightness)), PB
(Blue) and PR (Red) for enhanced video quality. Be sure to match the component
video and audio connections. For example, if connecting the video cable to
COMPONENT IN, connect the audio cable to COMPONENT IN also.
Each DVD Player/Set-Top box has a different back panel configuration.
When connecting a DVD Player/Set-Top box, match the color of the connection
terminal to the cable.
DVD Player / Set-Top Box
TV Rear Panel
Audio Cable (Not supplied)2
Component Cable (Not supplied)1
Camcorder
TV Side Panel
S-Video Cable(Not supplied)
1
Video Cable (Not supplied)1
Audio Cable (Not supplied)2
or
BN68-01192F-02Eng-1.indd 12 2007-03-23 ソタネト 3:10:26
English - 13
Connecting a DVD Player/Set-Top Box via DVI
This connection can only be made if there is a DVI Output jack on the external device.
1 Connect a HDMI/DVI Cable
or DVI-HDMI Adapter
between the [HDMI IN 1] jack
on the TV and the DVI jack
on the DVD Player/Set-Top
Box.
2 Connect Audio Cables
between the DVI IN (HDMI 1)
[R-AUDIO-L] jack on the TV
and the AUDIO OUT jacks on
the DVD Player/Set-Top Box.
Each DVD Player/Set-Top box has a different back panel configuration.
When connecting a DVD Player/Set-Top box, match the color of the connection
terminal to the cable.
When using an HDMI/DVI cable connection, you must use the HDMI IN1 terminal.
DVD Player / Set-Top Box
TV Rear Panel
Audio Cable (Not supplied)2
HDMI/DVI Cable (Not supplied)1
Connecting a DVD Player/Set-Top Box via HDMI
This connection can only be made if there is an HDMI Output jack on the external device. This connection will
provide the highest quality picture.
1 Connect an HDMI Cable
between the HDMI IN 2 on
the TV and the HDMI OUT on
the DVD Player/Set-Top Box.
What is HDMI?
HDMI, or high-definition multimedia interface, is an interface that enables the
transmission of digital audio and video signals using a single cable without
compression.
The difference between HDMI and DVI is that the HDMI device is smaller in size and
has the HDCP (High Bandwidth Digital Copy Protection) coding feature installed.
Each DVD Player/Set-Top box has a different back panel configuration.
When connecting a DVD Player/Set-Top box, match the color of the connection
terminal to the cable.
When connecting via HDMI, you do not need to connect Audio Cables. You only
need to connect Audio cables when connecting via HDMI/DVI.
HDMI Cable (Not supplied)1
DVD Player / Set-Top Box
TV Rear Panel
BN68-01192F-03Eng-1.indd 13 2007-03-27 ソタタ・9:39:35
English - 14
Connecting an Amplifier/DVD Home Theater
1 Connect Audio Cables
between the AUDIO OUT
[R-AUDIO-L] on the TV and
AUDIO IN [L-AUDIO-R] on
the Amplifier/DVD Home
Theater.
When an audio amplifier is
connected to the “AUDIO
OUT [R-AUDIO-L]” terminals:
Decrease the gain (volume)
of the TV, and adjust the
volume level with the
Amplifier’s volume control.
Each Amplifier/DVD Home Theater has a different back panel configuration.
When connecting an Amplifier/DVD Home Theater, match the color of the
connection terminal to the cable.
Amplifier/DVD Home Theater
TV Rear Panel
Audio Cable (Not supplied)
Connecting a PC
Using the D-Sub Cable
1 Connect a D-Sub Cable
between PC IN [PC] jack on
the TV and the PC output
jack on your computer.
2 Connect a PC Audio Cable
between PC IN [AUDIO] jack
on the TV and the Audio Out
jack of the sound card on
your computer.
Using the HDMI/DVI Cable
1 Connect a HDMI/DVI cable
between the [HDMI IN 1] jack
on the TV and the PC output
jack on your computer.
2
Connect a 3.5 mm Stereo plug
to 2 RCA cable between the
DVI IN (HDMI 1) [R-AUDIO-L]
jack on the TV and the Audio
Out jack of the sound card on
your computer.
Each PC has a different back panel configuration.
When connecting a PC, match the color of the connection terminal to the cable.
When using an HDMI/DVI cable connection, you must use the HDMI IN1 terminal.
PC
TV Rear Panel
PC Audio Cable (Not supplied)2
D-Sub Cable (Not supplied)1
Connecting a Digital Audio System
The rear panel jacks on your TV make it easy to connect a Digital Audio System to your TV.
1 Connect an Optical Cable
between the DIGITAL AUDIO
OUT (OPTICAL) jacks on
the TV and the Digital Audio
Input (OPTICAL) jacks on the
Digital Audio System.
When a Digital Audio System
is connected to the “DIGITAL
AUDIO OUT (OPTICAL)”
terminal:
Decrease the gain (volume)
of the TV, and adjust the
volume level with the
system’s volume control.
What is OPTICAL?
Converts the electric signal into an optical light signal, and transmits it through glass
fibers. S/PDIF is a transmission system of digital audio in the form of a light wave
that uses a glass conductor.
5.1CH audio is possible when the TV is connected to an external device
supporting 5.1CH.
Each external input source device has a different back panel configuration.
If you have an external device (DVD. Cable/Set-top box) connected via HDMI to
the TV, audio is not output from the Optical jack.
Digital Audio System
TV Rear Panel
Optical Cable (Not supplied)
Using the D-Sub Cable
Using the HDMI/DVI Cable
TV Rear Panel
PC
3.5 mm Stereo plug to 2 RCA Cable (Not supplied)2
HDMI/DVI Cable (Not supplied)1
BN68-01192F-02Eng-1.indd 14 2007-03-23 ソタネト 3:10:33
English - 15
Operation
Turning the TV On and Off
Press the POWER button on the remote control.
You can also use the POWER button on the TV.
It may take a while when your TV starts.
Plug & Play Feature
When the TV is initially powered On, basic settings proceed automatically and subsequently:
1 Press the POWER button on the remote control.
The message Menu language, Shop Mode, Channels and Time will be set. is
displayed.
2 Press the ENTER button to enter the language.
Press the ▲ or ▼ button to select language, then press the ENTER button.
The message Select Home Mode when installing this TV at home. is
automatically displayed.
3 Press the ◄ or ► button to select Shop or Home, then press the ENTER
button.
The default selection is Home.
We recommend setting the TV to Home mode for the best picture in your
home environment.
Shop mode is only intended for use in retail environments.
If the unit is accidentally set to Shop mode and you want to return to
Dynamic (Home) mode, press the Volume button and then hold down the
MENU button for five seconds on the TV panel.
4 Press the ▲ or ▼ button to memorize the channels of the selected connection.
Press the ENTER button to select Start.
If the antenna is connected to ANT1 IN(AIR), select Air and if it is connected
to ANT 2 IN(CABLE), select
Cable.
If both ANT 1 IN(AIR) and ANT 2 IN(CABLE) are connected,
select the Air + Cable.
In Cable mode, select the correct analog signal cable system source from
among STD, HRC, and IRC by pressing the ▲ or ▼ button, then press the
ENTER button. If you have Digital cable TV, select the cable system signal
source for both Analog and Digital. Contact your local cable company to
identify the type of cable system that exists in your particular area.
To memorize the channels, press the ► button to select
Start, then press
the ENTER button.
Contact your local cable company to identify the type of cable system that
exists in your particular area.
Continued...
Menu language, Shop Mode,
Channels and Time will be set.
i
Start
Select Home Mode when installing this TV at home.
Plug & Play
Enter
Skip
Shop
Home
Move
Select the language of the OSD.
Menu Language :
Plug & Play
English
Spanish
French
Enter
Skip
Move
Select the antennas to memorize.
Air
Cable
Air + Cable
Plug & Play
Start
Start
Start
Enter
Skip
Move
RETURN
FAV.CH
Plug & Play
Enter
Skip
Move
Select the cable system.
STD
HRC
IRC
Analog
STD
HRC
IRC
Digital
Start
BN68-01192F-02Eng-1.indd 15 2007-03-23 ソタネト 3:10:37
English - 16
5 The TV will begin memorizing all of the available channels.
After all the available channels are stored, the Auto program menu reappears.
Press the ENTER button when channel memorization is complete.
Clock Mode menu is automatically displayed.
To stop the search before it has finished, press the ENTER button with Stop
selected.
6 Press the ENTER button.
Press the ▲ or ▼ button to select Manual if you want to set the current
time manually, then press the
ENTER button. Set current date and time. is
displayed.
If you select Auto, Set to daylight savings time. is displayed, then go to
step 9.
7 Press the ◄ or ► button to move to Month, Day, Year, Hour, Minute, or
am/pm. Set the date and time you want by pressing the ▲ or ▼ button,
then press the MENU button.
You can set the Month, Day, Year, Hour, and Minute directly by pressing
the number buttons on the remote control.
8 The message Enjoy your watching. is displayed.
When you have finished, press the ENTER button.
Even if the ENTER button is not pressed, the message will automatically
disappear after several seconds.
Setting the Clock Automatically
9 Press the ENTER button.
Press the ▲ or ▼ button to select On or Off, then press the ENTER button.
Select the time zone in which you live. menu is automatically displayed.
10 Press the ▲ or ▼ button to highlight the time zone for your local area (and
to move the highlight to the appropriate time zone on the map of the United
States).
Press the ENTER button.
If clock is not automatically set, see page 48 to set the clock.
11 The message
Enjoy your watching. is displayed.
When you have finished, press the ENTER button.
Even if the ENTER button is not pressed, the message will automatically
disappear after several seconds.
Continued...
Select the clock mode.
Clock Mode :
Plug & Play
Manual
Auto
Enter
Skip
Move
Plug & Play
Auto Program in progress.
Cable Channel 67
68%
Stop
Enter
Plug & Play
Auto Program is completed.
14 Channels were memorized.
Air : 9 , Cable : 5.
OK
Enter
Enjoy your watching.
OK
i
Set to daylight savings time.
Daylight Savings Time :
Plug & Play
On
Off
Enter
Skip
Move
Select the time zone in which you live.
Plug & Play
Newfoundland
Atlantic
Eastern
Central
Mountain
Pacific
Alaska
Hawaii
Enter
Skip
Move
Enjoy your watching.
OK
i
Skip
Plug & Play
Enter
Set the current time.
Skip
Move
--
--
Day Month Year
Hour Minute am/pm
Adjust
Skip
--
--
--
----
BN68-01192F-02Eng-1.indd 16 2007-03-23 ソタネト 3:10:39
English - 17
If you want to reset this feature...
1 Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Setup, then press the ENTER button.
2 Press the ENTER button to select Plug & Play. For further details on setting up
options, refer to the page 15~16.
The Plug & Play feature is only available in the TV and DTV mode.
Changing Channels
Using the Channel Buttons
1 Press the CH or CH button to change channels.
When you press the CH or CH button, the TV changes channels in
sequence. You will see all the channels that the TV has memorized.
(The TV must have memorized at least three channels). You will not
see channels that were either erased or not memorized. See page 19 to
memorize channels.
Using the Number Buttons
1 Press the number buttons to go directly to a channel. For example, to select
channel 27, press 2, then 7.
The TV will change channels when you press the second number.
Using the “
-
” Button
The “
-
” button is used to select stations that broadcast a digital signal.
1 For example, for Channel 7-1, press 7, then
-
, then 1.
HD indicates the TV is receiving a Digital High Definition signal.
SD indicates the TV is receiving a Standard Definition signal.
For quick channel change, press the number buttons, then press the ENTER
button.
Using the PRE-CH Button to select the Previous Channel
Use the number buttons to quickly tune to any channel.
1 Press the PRE-CH button. The TV will switch to the last channel viewed.
To quickly switch between two channels that are far apart, tune to one
channel, then use the number button to select the second channel.
Then use the PRE-CH button to quickly alternate between them.
Menu language, Shop Mode,
Channels and Time will be set.
Start
i
Plug & Play
Language : English
Time
Game Mode : Off
V-Chip
Caption
Menu Transparency
: Medium
More
SetupT V
Enter
Move
Return
RETURN
FAV.CH
RETURN
FAV.CH
RETURN
FAV.CH
RETURN
FAV.CH
BN68-01192F-02Eng-1.indd 17 2007-03-23 ソタネト 3:10:41
English - 18
Adjusting the Volume
Using the Volume Buttons
1 Press the VOL + or VOL button to increase or decrease the volume.
Using the Mute Button
At any time, you can cut off the sound using the
MUTE button.
1 Press MUTE and the sound cuts off.
The word “Mute” will appear in the lower-left corner of the screen.
2 To turn mute off, press the MUTE button again, or simply press the VOL + or
VOL –
button.
Viewing the Display
The display identifies the current channel and the status of certain audio-video settings.
1 Press the INFO button on the remote control.
The TV will display the channel, the type of sound, and the status of certain
picture and sound settings.
Press the INFO button once more or wait approximately 10 seconds and it disappears
automatically.
Viewing the Menus
1 With the power on, press the MENU button.
The main menu appears on the screen. Its left side has five icons:
Picture, Sound, Channel, Setup, Input.
2 Use the ▲ or ▼ button to select one of the five icons.
Then press the ENTER button to access the icon’s sub-menu.
3 Press the EXIT button to exit.
It takes about one minute until the on-screen menu disappears.
RETURN
FAV.CH
Air 28
Picture Mode : Dynamic
Sound Mode : Custom
MTS : Stereo
12 : 00 am
Mono
RETURN
FAV.CH
RETURN
FAV.CH
Mode : Dynamic
Contrast 100
Brightness 45
Sharpness 75
Color 55
Tint G 50 R 50
More
PictureT V
Enter
Move
Exit
BN68-01192F-02Eng-1.indd 18 2007-03-23 ソタネト 3:10:44
English - 19
Memorizing the Channels
Your TV can memorize and store all of the available channels for both “off-air” (air) and cable channels. After the
available channels are memorized, use the CH or CH button to scan through the channels. This eliminates
the need to change channels by entering the channel digits. There are three steps for memorizing channels:
selecting a broadcast source, memorizing the channels (automatic) and adding and deleting channels (manual).
Selecting the Video Signal-source
Before your television can begin memorizing the available channels, you must
specify the type of signal source that is connected to the TV (i.e. an air or a cable
system).
1 Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Channel, then press the ENTER button.
2 Press the ENTER button select Antenna.
Press the ▲ or ▼ button to select Air or Cable, then press the ENTER button.
Press the
EXIT button to exit.
Storing Channels in Memory (Automatic Method)
1 Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Channel, then press the ENTER button.
2 Press the ▲ or ▼ button to select Auto Program, then press the ENTER
button.
3 Press the ▲ or ▼ button to select the antenna connection, then press the
ENTER button.
Air: “Air” antenna signal.
Cable: “Cable” antenna signal.
Air+Cable: “Air” and “Cable” antenna signals.
If the antenna is connected to ANT 2 IN (CABLE), select Cable and if it is
connected to ANT 1 IN (AIR), select
Air.
If both ANT 1 IN and ANT 2 IN are connected, select the Air + Cable.
If you selected Air, then go to step 5.
4 Press the ▲ or ▼ to select the correct analog signal cable system source from
among STD, HRC, and IRC, then press the ENTER button. If you have Digital
cable TV, select the cable system signal source for both Analog and Digital.
If you have Digital cable TV, select the signal source for both Analog and
Digital.
STD, HRC, and IRC identify various types of cable TV systems. Contact
your local cable company to identify the type of cable system that exists in
your particular area. At this point the signal source has been selected.
5 The TV begins memorizing all available stations.
If you want to stop Auto Programming, press the
ENTER button. The Stop
Auto Program? message will be displayed. Select Yes by pressing the ◄ or ►
button.
Press the
EXIT button to exit.
The TV must be connected to antenna/cable in order to receive digital TV
signals. Even if a particular channel is deleted from the memory, you can
always tune to that channel directly by using the number buttons on the
remote control.
All available DTV and analog channels are automatically stored in
memory.
• It takes approximately 3 to 10 minutes to memorize channels.
Auto Program
Auto Program in progress.
Cable Channel 67
68 %
Stop
Enter
Antenna : Air
Auto Program
Clear Scrambled Channel
Channel List
Name
Fine Tune
Signal Strength
LNA : On
ChannelT V
Enter
Move
Auto ProgramT V
Select the antennas to memorize.
Air
Cable
Air + Cable
Start
Enter
Move
Start
Start
Auto Program
Stop Auto Program?
Yes No
68 %
Antenna : Air
Auto Program
Clear Scrambled Channel
Channel List
Name
Fine Tune
Signal Strength
LNA : On
ChannelT V
Enter
Move
Return
Antenna : Air
Auto Program
Clear Scrambled Channel
Channel List
Name
Fine Tune
Signal Strength
LNA : On
ChannelT V
Enter
Move
Air
Cable
Return
Return
Return
Select the cable system.
Auto ProgramT V
Enter
Move
Return
STD
HRC
IRC
Analog
STD
HRC
IRC
Digital
Start
Return
Enter
Move
Return
BN68-01192F-02Eng-1.indd 19 2007-03-23 ソタネト 3:10:46
English - 20
Setting Up the Remote to Operate Your VCR
1 Turn off your VCR.
2 Press the
VCR button on your TV’s remote control.
3 Press the SET button on your TV’s remote control.
4 Using the number buttons on your remote control, enter three digits of the VCR code listed
on page 22 of this manual for your brand of VCR. Make sure you enter three digits of the
code, even if the first digit is a “0”. (If more than one code is listed, try the first one.)
5 Press the POWER button on the remote control. Your VCR should turn on if your remote
is set up correctly.
If your VCR does not turn on after set-up, repeat steps 2, 3 and 4, but try one of the other codes
listed for your brand of VCR. If no other codes are listed, try each VCR code, 000 through 080.
Note on Using Remote Control Modes: VCR
When your remote control is in VCR mode, the volume buttons still control your TV’s volume.
Setting Up the Remote to Operate Your Cable Box
1 Turn off your cable box.
2 Press the CABLE button on your TV’s remote control.
3 Press the
SET button on your TV’s remote control.
4 Using the number buttons on your remote control, enter three digits of the cable box code
listed on page 23 of this manual for your brand of cable box. Make sure you enter three
digits of the code, even if the first digit is a “0”. (If more than one code is listed, try the first
one.)
5 Press the
POWER button on the remote control.
Your cable box should turn on if your remote is set up correctly.
If your cable box does not turn on after set-up, repeat steps 2, 3 and 4, but try one of the other
codes listed for your brand of cable box. If no other codes are listed, try each code, 000 through
046.
Note on Using Remote Control Modes: Cable Box
When your remote control is in CABLE mode, the volume buttons still control your TV’s volume.
Continued...
Setting Up Your Remote Control
After your remote control has been properly set up, your remote control can operate in five different modes:
TV, VCR, Cable, DVD, or Set-Top Box. Pressing the corresponding button on the remote control allows you to
switch between these modes, and control whichever piece of equipment you choose.
The remote control might not be compatible with all DVD Players, VCRs, Cable boxes, and Set-Top Boxes.
RETURN
FAV.CH
RETURN
FAV.CH
RETURN
FAV.CH
RETURN
FAV.CH
BN68-01192F-02Eng-1.indd 20 2007-03-23 ソタネト 3:10:47
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144

Samsung HP-T4254 Manuel utilisateur

Catégorie
Téléviseurs à écran plasma
Taper
Manuel utilisateur
Ce manuel convient également à

dans d''autres langues