Crate Amplifiers GX-40D Manuel utilisateur
- Catégorie
- Amplificateur d'instruments de musique
- Taper
- Manuel utilisateur
Ce manuel convient également à
AMPLIFIER
OWNER’S MANUAL
Congratulations!
You are now the proud owner of the versatile and powerful Crate GX-40C+/40D
amplifier with Stereo Chorus and Digital Sound Processing (GX-40D only). This amplifi-
er offers you more features and better sound than virtually any amp in its class: True
Stereo Chorus. A Stereo Effects Loop. Stereo Headphones / Line Out jack. Stereo
External Speaker jacks. A front-panel insert jack to add even more effects. Each of the
two extraordinary channels have their own Level controls and tones: the Overdrive chan-
nel features separate Gain and Level controls along with Crate’s exclusive Shape con-
trol for quick and precise tone setting, plus a Mid Shift switch for even more control over
your sound. Switch over to the Clean channel, with its own separate Gain and Level con-
trols plus three-band EQ for dialing in just the right sounds.
Like all Crate products, your GX-40C+/40D is Musician Made in the U.S.A., using
only the best components. Extensive testing at the hands (and ears) of skilled technicians
and musicians insures you that this amplifier is the absolute best it can be.
In order to get the most out of your new amplifier, we strongly urge you to go over
the information contained in this manual before you begin playing.
And thank you
for choosing
GX-40C+/40D Amplifier
1 2 3 4 98 105 6 7 11 12 13 14 1615 17 18 19 20 21
1: INPUT: Connect your guitar here using a shielded instrument
cable.
OVERDRIVE CHANNEL: Ahigh gain channel giving you sounds
from a slight edge to serious overdrive.
2: GAIN: Sets the amount of compression and distortion for the
Overdrive channel with this control. Rotating the control towards
the right increases the intensity of overdrive distortion.Crate’s
exclusive “Flex-Wave” circuitry uses Sequential Cascading
Gains to deliver distortion which is rich in harmonics and respon-
sive to your touch. Use the Gain control along with the Shape
and Level (#3 and 5) to create a wide variety of lead sounds.
3: SHAPE: Quickly “dial in” just right lead sounds with this con-
trol which adjusts the “shape” of the distortion wave, producing a
wide variety of tone combinations. Basically, rotating the control
towards the left enhances the mid frequencies; rotating it
towards the right enhances more of the low and high frequencies
simultaneously, with a myriad of tonal variations in between.
4: MID SHIFT: Engaging this switch deepens the notch at the
clockwise position of the Shape control (#3).
5: LEVEL: Sets the output volume for the Overdrive channel
with this control: in the far-left position there is no output; as you
rotate the control to the right the output level increases.
6. OVERDRIVE CHANNEL LED: This LED glows red when the
Overdrive channel is selected.
7: CHANNEL SELECT: Press this switch IN to activate the
Overdrive channel; press it again to the OUT position for the
Clean channel. This switch can also be used in conjunction with
the DSP section (#14 and 15, GX-40D only) to change your dig-
ital reverb mode (see “The DSP Section” on the far right panel).
A footswitch (see #26) overrides this control.
8. CLEAN CHANNEL LED: This LED glows green when the
Clean channel is selected.
CLEAN CHANNEL: A normal gain channel designed to give you
crystal clear sounds to medium distortion.
9: GAIN: Set the amount of overdrive to the Clean channel with
this control. At lower settings the sound will be crystal clear.
Rotate towards the right to increase the amount of distortion,
with a fat, bluesy sound in the full clockwise position. Use the
Gain control along with the Tone and Level controls (#10 thru 13)
to create a wide variety of rhythm sounds.
10: LOW: Adjust the low frequency output level of the Clean
channel with this control: turning the control to the left reduces the
low frequency output; turning it to the right increase the low fre-
quency output. The Low control allows a total range of ±22dB of
boost or cut at 80Hz. Due to the large amounts of low end avail-
able, you may want to roll off the bass at high volume levels.
11: MID: Adjust the mid frequency output level of the Clean
channel with this control: the center position is “flat” (no boost or
cut). Turning the control to the left reduces the midrange output;
turning it to the right increases the midrange output. The Mid
control allows a total range of ±14dB of boost or cut at 800Hz.
12: HIGH: Adjust the high frequency output level of the Clean
channel with this control: the center position is “flat” (no boost or
cut). Turning the control to the left reduces the high frequency
output; turning it to the right increases the high frequency output.
The High control allows a total range of ±20dB of boost or cut at
8kHz.
13. LEVEL: Set the output volume for the Rhythm channel with
this control: in the far-left position there will be no output; as you
rotate the control to the right the output level increases.
GX-40C+ (shown above):
14, 15: REVERB, OVERDRIVE / REVERB, CLEAN: Set the
amount of reverberation for the appropriate channel with these
controls: in the far left position the signal will be “dry” (without any
reverb). As you rotate the control to the right the amount of rever-
beration increases.
GX-40D (not shown):
14: DSP MODE: Select the type of digital sound processing
effect with this control. Each channel and chorus setting will
“remember” its effect, allowing you to switch between channels
and chorus on/off without having to reset the Mode control.
15: DSP LEVEL: Adjust the amount of digital signal processing
effect with this control: in the full-left position the signal is “dry”
(no reverb/effect); rotating the control to the right increases the
amount of effect.
16: INSERT: This jack allows you to add a footpedal or mono
effect into the amp loop, after the tone controls, prior to the cho-
rus and amplifier sections. The jack is a stereo 1/4” phone jack,
wired as follows: Tip = signal out, ring = signal in, sleeve = com-
mon ground. (Refer to the illustration on the panel to the right.)
17: CHORUS ON: Activate the Stereo Chorus section by press-
ing this switch IN; press it again to release it to the OUT position
to turn the Chorus effect off. This switch can also be used in con-
junction with the DSP section (GX-40D only) to change your dig-
ital reverb mode (see “The DSP Section” on the far right panel).
A footswitch (see #26) overrides this control.
18: DEPTH: Set the intensity of the Stereo Chorus effect with
this control: in the far left position there will be almost no chorus;
as you rotate the control to the right the amount of effect increas-
es.
19: RATE: Set the speed of the Stereo Chorus effect with this
control: to the left for slow, smooth “phasing” sounds, to the right
for faster “vibrato” sounds.
20: ON LED: The word “ON” glows red when you turn the ampli-
fier on, showing you that it is powered up and ready to play.
21: POWER SWITCH: This heavy-duty rocker-type switch turns
the amplifier ON in the left position, OFF in the right position. The
ON LED (#20) works with this switch as a visual indicator.
FRONT PANEL:
GX-40C+/40D Amplifier
22: POWER CORD: This heavy-duty, grounded, three wire
power cord is to be plugged into ONLY a safely-wired, ground-
ed 120 volt 60 cycle AC power outlet. DO NOT attempt to
defeat the ground connection of this cable! If your amplifier was
purchased outside of the United States, see its rear panel for
the proper power rating.
23: EXTERNAL SPEAKERS: You may connect the outputs of
the GX-40C+/D to your external speakers having a rated
impedance of at least 2 ohms each, using these jacks. When
connecting speakers, use a matched pair: two with the same
impedances, to insure optimum performance from the amplifier.
Since these are series conenctions, there is no chance of dam-
aging the amplifier with too small of an inpedacne load.
24: STEREO HEADPHONE / LINE OUT JACK: This dual-
function stereo jack provides you with a means to connect a
pair of stereo headphones for private practice sessions, or to
obtain a stereo line-level output signal to send to a recording
console, mixing board or to another pair of power amplifiers.
The internal speakers are muted whenever a plug is inserted
into this jack. The wiring for the jack is as follows:
Tip: Right channel
Ring: Left channel
Sleeve: Common ground
25: STEREO EFFECTS LOOP: Connect the SEND jack to the
inputs of your stereo effects device to send a post-EQ, post-
chorus, pre-amplified signal for processing. Connect the out-
puts of the effects device to the RETURN jack to return the
processed signal to the amplifier. The jacks are stereo 1/4”
phone jacks, wired as follows:
Tip: Right channel
Ring: Left channel
Sleeve: Common ground
If your effects device has stereo input and output jacks, use a
pair of three-conductor stereo patch cords to connect it. If the
device has separate left and right jacks, use a pair of one-
stereo-male to two-mono-female Y-adapters to make the con-
nections.
26: FOOTSWITCH: Plug a dual footswitch (such as the Crate
model FS-60) here to control channel selection and chorus
on/off. This stereo 1/4” phone jack is wired as follows:
Tip: Channel select
Ring: Chorus on/off
Sleeve: Common ground
Connecting to the Insert jack:
The Insert jack (#16) lets you patch external effects into the ampli-
fier just prior to its power amp stage. Use Crate’s CYC6MS
stereo-to-mono Y-cord or an adapter such as Crate’s CA11Y and
2 1/4” mono signal cables to connect to the effect as shown below.
22
PATENT #5,032,796
MADE IN THE U.S.A.
BY SLM ELECTRONICS
1400 FERGUSON AVE.
ST. LOUIS, MO 63133
EXTERNAL SPEAKERS
20W RMS PER CHANNEL
2 OHM MIN. LOAD
LEFT RIGHT
23 24
RISK OF ELECTRIC
SHOCK - DO NOT OPEN
CAUTION
RISQUE DE CHOC ELECTRIQUE.
NE PAS OUVRIR.
TO REDUCE THE
RISK OF FIRE OR
ELECTRIC SHOCK,
DO NOT EXPOSE
THIS EQUIPMENT
TO RAIN OR MOIS-
TURE.
AVIS:
MODEL:
SERIAL:
LINE: V ~ Hz
WATTS: MAX
GX-40C+
GX40C12006902
120 60
STEREO
EFFECTS LOOP
STEREO
HEADPHONES/
LINE OUT
FOOTSWITCH
RETURN CHANNEL
SELECT/
CHORUS
SEND
2625
TIP
RING
SLEEVE
SEND
RETURN
GROUND
Stereo-to-mono Y-cord:
to Insert jack
(CYC6MS)
(CA11Y)
"Send"
plug:
to
effect
"IN"
"Return"
plug:
from
effect
"OUT"
External Effect
TIP
RING
SLEEVE
Y-adapter and 2 cables:
to Insert jack
to
effect
"IN"
from
effect
"OUT"
Ring =
"Return"
Tip =
"Send"
External Effect
REAR PANEL:
WARNING: DO NOT attempt to use headphones in the
Speaker jacks! Permanent hearing damage could result!
GX-40C+/40D Amplifier
THE DSP SECTION (GX-40D only):
The DSP’s 32 position Mode control allows you to instantly access the exact type of effect you want – from classic rever-
beration to radical “backwards sounds – for any of the Channel/Chorus combinations. The setting of the Mode control will
determine the type of effect for whatever Channel/Chorus combination the amp is set to at the time you adjust the Mode con-
trol. Once set, the GX-40D’s non-volitale memory retains the setting until you reset it.
EXAMPLE: Plug in your guitar and turn on the amplifier. Set Channel Select to the Clean channel. Now set the Mode con-
trol to “12” (gated reverb, medium). Strike a chord on your guitar and listen to the sound of the effect. Press in the Channel
switch to choose the Overdrive channel, then set the Mode control to “27” (large hard surface echo). Strike a chord and listen
to the results. Now press the Channel switch again to get back to the Clean channel and strike a chord – even though you
haven’t changed the setting of the mode control, the amplifier “remembered” that you had programmed in setting “12” and kept
the effect as you left it.
THERE’S MORE: With the Channel Select and Chorus being switchable, you can program each of the four
Channel/Chorus combinations with their own Mode settings. If you want to control Reverb on/off with the Chorus footswitch,
for example, set the Mode to “0” (bypass), hit the footswitch and set Mode to “5” (large hall, bright). Now you have the ability
to switch the reverb on and off with the footswitch.
With the footswitch you have a choice of two reverb settings for each of the channel selections, for the most flexibility and
versatility possible!
THE DSP SETTINGS:
# Name Type Description
0 Off None Bypass—no signal processing occurs.
1 Sm Rm, Bright Small Reverb 8’ x 8’ empty room with hardwood floors.
2 Sm Rm, Dark Small Reverb 8’ x 8’ carpeted room with up to four people.
3 Sm Hall, Bright Small Reverb 20’ x 40’ Rehearsal Hall, wood floors, hard walls.
4 Sm Hall, Dark Small Reverb 20’ x 40’ carpeted Rehearsal Hall with draped walls and up to 30 people.
5 Lg Hall, Bright Large Reverb 50’ x 100’ empty Rehearsal Hall, 20’ ceilings.
6 Lg Hall, Dark Large Reverb 50’ x 100’ Rehearsal Hall with up to 50 friends and crew.
7 Avg Club, Bright Large Reverb 500 capacity empty club, wood floors, afternoon sound check.
8 Avg Club, Dark Large Reverb 500 capacity club, wood floors, stuffed with people.
9 Cncrt Hall, Brt Large Reverb 5,000-seat Concert hall, hard back wall, afternoon sound check.
10 Cncrt Hall, Dark Large Reverb 5,000-seat Concert hall, SRO at back wall, sold out show.
11 Stadium Large Reverb 40,000-seat round Stadium, afternoon sound check, 100 crew & VIPs only.
12 Gated Rev, Med Special Reverb Studio Effect–Engineer cuts off reverb slightly after each note. (220ms Gate)
13 Gated Rev, Long Special Reverb Studio Effect—Engineer lets note ring, then cuts it off. (350ms Gate)
14 Plate Reverb Special Reverb Studio Effect—Simulates Steel Plate Reverb.
15 Traditional Rev Special Reverb Studio Effect—Simulates old-fashioned multi-spring tube reverb unit.
16 Slapback, Short Delay 125ms delay + small reverb; Elvis’ favorite.
17 Slapback, Med Delay 350ms delay + small reverb; Rockabilly special.
18 Slapback, Long Delay 557ms delay only, 630’ travel time of sound.
19 Sh Md Surf Echo Echo 85ms delay with 14.2% regen. & small reverb.
20 Sh Hd Surf Echo Echo 85ms delay with 27.3% regeneration.
21 Sh/Med Md Surf Echo 280ms delay with 21.8% regen & small reverb.
22 Md Sft Surf Echo Echo 335ms delay with 12.5% regeneration.
23 Md Hd Surf Echo Echo 335ms delay with 26.5% regen. & small reverb.
24 Md Glass Echo Echo 335ms delay with 43.7% regeneration.
25 Lg Sft Surf Echo Echo 485ms delay with 7.8% regeneration.
26 Lg Md Surf Echo Echo 485ms delay with 20.3% regeneration.
27 Lg Hd Surf Echo Echo 485ms delay with 39.2% regen & small reverb.
28 Infinite Delay Special Effect 506ms delay with over 90% regeneration.
29 Thickener Special Effect 33ms-based sound fattener @ selected freqs.
30 Multi-Tap Special Effect Multi-thickener with some subtle delays added.
31 Reverse Special Effect “Backwards masking” effect (number nine, number nine,...)
GX-40C+/40D Amplifier
SYSTEM BLOCK DIAGRAM:
SUGGESTED ST
ARTING SETTINGS:
The GX-40C+/40D is covered with a durable black Tolex material: wipe it clean with a lint-free cloth.
Never spray cleaning agents onto the cabinet. Avoid abrasive cleansers which would damage the finish.
IN out
DSP MODE AT "30" FOR OVERDRIVE, "23" FOR CLEAN
OUT IN
DSP MODE AT "13", LEVEL AT "8"
OUT IN
DSP MODE AT "15", LEVEL AT "8"
IN IN
DSP MODE AT "27" , LEVEL AT "8"
GAIN SHAPE LEVEL
INPUT
CHANNEL
SELECT
FLEX WAVE
STAGE
LOWGAIN MID HIGH LEVEL
OVERDRIVE
CLEAN
BUFFER
INSERT
CLEAN CHANNEL
OVERDRIVE
CHANNEL
LEFT
SPEAKER
EXTERNAL
SPKR JACK
CHORUS
GX-40D:
HEADPHONE/
LINE OUT
SEND RETURN
CHANNEL
SELECT
LEVEL
DSP
MODE
POWER
AMP
STEREO
EFFECTS LOOP
BUFFER
SEND RETURN
BUFFER
SPKR
COMP
RIGHT
SPEAKER
EXTERNAL
SPKR JACK
POWER
AMP
GX-40C+:
METAL CRUNCH SPARKLING CLEAN
HOT SRV WARBLE SRV WARBLE
ROCK RHYTHM BLUESY ATTACK
SMOOTH LEAD WARM CLEAN
©1997 SLM ELECTRONICS, A DIVISION OF ST. LOUIS MUSIC, 1400 FERGUSON, ST. LOUIS, MO. 63133
P/N 47-574-03 • 04/97
Crate continually develops new products, as well as improves existing ones. For this reason, the
specifications and information in this Crate manual are subject to change without notice.
GX-40C+/40D Amplifier
THIS EQUIPMENT HAS BEEN
DESIGNED AND ENGINEERED TO
PROVIDE SAFE AND RELIABLE
OPERATION. IN ORDER TO PRO-
LONG THE LIFE OF THE UNITAND
PREVENT ACCIDENTAL DAM-
AGES OR INJURY, PLEASE FOL-
LOW THESE PRECAUTIONARY
GUIDELINES:
CAUTION: TO REDUCE THE RISK
OF ELECTRIC SHOCK, DO NOT
OPEN CHASSIS; DO NOT DEFEAT
OR REMOVE THE GROUND PIN
OF THE POWER CORD; CON-
NECT ONLY TO A PROPERLY
GROUNDED AC POWER OUTLET.
WARNING: TO REDUCE THE RISK
OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS EQUIP-
MENT TO RAIN OR MOISTURE.
CAUTION: NO USER-SERVICE-
ABLE PARTS INSIDE. REFER SER-
VICING TO QUALIFIED SERVICE
PERSONNEL.
CAUTION: OUR AMPLIFIERS ARE
CAPABLE OF PRODUCING HIGH
SOUND PRESSURE LEVELS.
CONTINUED EXPOSURE TO HIGH
SOUND PRESSURE LEVELS CAN
CAUSE PERMANENT HEARING
IMPAIRMENT OR LOSS. USER
CAUTION IS ADVISED AND EAR
PROTECTION IS RECOMMENDED
IF UNIT IS OPERATED AT HIGH
VOLUME.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER.
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
"IT IS NECESSARY FOR THE USER TO REFER TO THE INSTRUCTION MANUAL"
“ES NECESARIO QUE EL USUARIO SE REFIERA AL MANUAL DE INSTRUCCIONES.”
"REFERREZ-VOUS AU MANUAL D'UTILISATION"
"UNBEDINGT IN DER BEDIENUNGSANLEITUNG NACHSCHLAGEN"
EXPLANATION OF GRAPHICAL SYMBOLS:
EXPLICACION DE SIMBOLOS GRAFICOS:
EXPLICATION DES SYMBÔLES GRAPHIQUES:
"DANGEROUS VOLTAGE"
“VOLTAJE PELIGROSO”
"DANGER HAUTE TENSION"
"GEFAHLICHE SPANNUNG"
=
=
PRECAUCION
RIESGO DE CORRIENTAZO
NO ABRA
PRECAUCION PARA DISMINUOIR EL RIESGO DE CORRIENTAZO
NO ABRA LA CUBIERTA
NO HAY PIEZAS ADENTRO QUE EL USARIO PUEDO REPARAR
DEJE TODO MANTENIMIENTO A LOS TECHNICOS CALIFICADOS
ATTENTION
RISQUE D'ELECTROCUTION
NE PAS OUVRIR
ATTENTION: POUR REDUIRE D'ELECTROCUTION NE PAS
ENLEVER LE COUVERCLE. AUCUNE PIECE INTERNE N'EST REPRABLE
PAR L'UTILISATEUR. POUR TOUTE REPARATION, S'ADRESSER A UN
TECHNICIEN QUALIFIE.
VORSICHT
ELEKTRISCHE SCHLAGGEFAHR
NICHT OFFENEN
VORSICHT: ZUR MINIMIERUNG ELEKTRISCHER SCHLAGGEFAHR NICHT
DEN DECKEL ABENHMEN. INTERNE TEILE KONNEN NICHT VOM
BENUTZER GEWARTET WERDEN. DIE WARTUNG IS QUALIFIZIERTEM
WARTUNGSPERSONAL ZU UBERLASSEN.
ESTE APARATO HA SIDO DISENADO Y
CONSTRUIDO PARA PROVEER ANOS
DE OPERACION SEGURA Y CONFI-
ABLE. PARA PROLONGAR LA VIDA DE
ESTA UNIDAD E IMPEDIR DANOS ACCI-
DENTALES POR FAVOR SIGA ESTAS
INSTRUCCIONES PREVENTIVAS:
PRECAUCION: PARA DISMINUIR EL
RIESGO DE DESCARGAS
ELECTRICAS: (1) NO ABRA LACUBIER-
TA, (2) NO ES RECOMENDABLE
REMOVER O DESACTIVAR LA PATA
DEL POLO A TIERRA DEL CABLE DE
CORRIENTE, CONECTE CORRECTA-
MENTE A UNA TOMA DE CORRIENTE A
TIERRA.
ADVERTENCIA: PARA EVITAR
DESCARGAS EL ECTRICAS O PELI-
GRO DE INCENDIO, NO DEJE ESTE
APARATO EXPUESTO A LA LLUVIA O
HUMEDAD.
PRECAUCION: NO HAY PIEZAS ADEN-
TRO QUE EL USUARIO PUEDE
REPARAR. DEJE TODO MANTENIMIEN-
TO A LOS TÉCNICOS CALIFICADOS.
PRECAUCION: NUESTROS AMPLIFI-
CADORES PUEDEN PRODUCIR NIVE-
LES DE PRESION DE SONIDO ALTO.
EXPOSICION CONTINUADA A LOS
NIVELES DE PRESION DE SONIDO
ALTO PUEDE CAUSA DANO PERMA-
NENTE A SU OIDO. ES ACONSEJADO
QUE USE PRECAUCION ALUSUARIO Y
ES RECOMENDADO PROTECCION
PARA LOS OIDOS SI LA UNIDAD ES
OPERADAA VOLUMEN ALTO.
CET ÉQUIPEMENTAVAIT ÉTÉ INVEN-
TÉ ET ARRANGÉ POUR POURVOIR
DES ANNÉES D'USAGE SAUF ET
SÛR. POUR PROLONGER LA VIE DE
CETAPPAREIL ETPOUR EMPÊCHER
LES DOMMAGES ET LES TORTS
ACCIDENTELS, SUIVEZ LES
INSTRUCTIONS DE PRÉCAUTION.
AVERTISSEMENT: POUR RÉDUIRE
LES RISQUES D'ÉLECTROCUTION:
(1) N’OUVREZ PAS LE CHÂSSIS, (2)
NE PAS ESSAYER DE SUPPRIMER
LABROCHE CORRESPONDANT À LA
TERRE.
ATTENTION: POUR RÉDUIRE LES
RISQUES D'UN FEU OU D'ÉLECTRO-
CUTION, N’EXPOSEZ PAS L'AP-
PAREIL À LA PLUIE OU À LA MOI-
TEUR.
ATTENTION: IL N'Y A PAS D’ÉLÉ-
MENTS RÉPARABLES DANS L'AP-
PAREIL. CONSULTER UN TECHNI-
CIEN QUALIFIÉ POUR LES RÉPARA-
TIONS.
ATTENTION: NOS AMPLIFICATEURS
SONT CAPABLES DE LA PRODUC-
TION DES NIVEAUX DE SON D'UNE
HAUTE PRESSION. L'EXPOSITION
CONTINUE AUX CES NIVEAUX PEUT
CAUSER LA SURDITÉ PERMA-
NENTE. LA PRUDENCE ESTADVISÉ
À UTILISATEUR ET LA PROTECTION
DES OREILLES EST RECOMMANDÉ
SI L'APPAREIL EST UTILISÉ À UN
HAUT NIVEAU DE VOLUME.
Output Power Rating >20 watts/channel, 4 ohms, 120VAC
Gain, Lead Channel 88dB @ 1kHz
Gain, Rhythm Channel 60dB @ 1kHz
Equalization, Overdrive Channel Crate’s exclusive Shape control, Mid Shift switch
Equalization, Clean Channel Low: ±22dB range @ 80Hz
Mid: ±14dB range @ 800Hz
High: ±20dB range @ 8kHz
Input Impedance 1M ohms
Signal To Noise Ratio, Overdrive Channel 64dB (Gain, Shape @ “0”, Level @ “10”)
Signal To Noise Ratio, Clean Channel 54dB (Gain, Level @ “10”, Tones @ “5”)
Maximum Input Signal Level Accepted 3 volts, peak-to-peak
Internal Speakers 2 - 8” Crate Custom Design, 4 ohm
Power Requirements Domestic: 120 VAC, 60Hz, 55VA
Export: 100/115VAC, 50/60Hz, 55VA
230VAC, 50/60Hz, 55VA
Cabinet Size and Weight 15.5” H x 20.75” W x 8.75” D, 32 lbs.
GX-40C+/40D TECHNICAL SPECIFICATIONS
-
1
-
2
-
3
-
4
-
5
-
6
Crate Amplifiers GX-40D Manuel utilisateur
- Catégorie
- Amplificateur d'instruments de musique
- Taper
- Manuel utilisateur
- Ce manuel convient également à
dans d''autres langues
- English: Crate Amplifiers GX-40D User manual
Documents connexes
-
Crate Amplifiers GX-140D Manuel utilisateur
-
-
-
Crate Amplifiers GX-40M Manuel utilisateur
-
-
-
-
-
-