Philips 2AANUSHB4385 Manuel utilisateur

Marque: Philips

Modèle: 2AANUSHB4385

Catégorie: Casques mobiles

Taper: Manuel utilisateur

Ce manuel convient également à

BASS+ SHB4385

SHB4385

BASS+

User manual

www.philips.com/support

1EN

Contents

1 Important safety instructions 2

Hearing Safety 2

General information 2

2 Your Bluetooth wireless

headset 3

What's in the box 3

Other devices 3

Overview of your Bluetooth

wireless headset 4

3 Get started 5

Charge the battery 5

Pair between both sides of the

headset 5

Pair your headset with the

Bluetooth device 6

4 Use your headset 7

Connect the headset to a

Bluetooth device 7

Power on/o 7

Manage your calls and music 7

LED indicator status 8

How to wear 8

5 Technical data 9

6 Notice 10

Declaration of conformity 10

Disposal of your old product

and battery 10

Compliance with EMF 11

Trademarks 11

7 Frequently asked questions 12

1 Important

safety

instructions

Hearing Safety

Danger

• To avoid hearing damage, limit the time you

use headset at high volume and set the

volume to a safe level. The louder the volume,

the shorter the safe listening time is.

Be sure to observe the following

guidelines when using your headset.

• Listen at reasonable volumes for

reasonable periods of time.

• Be careful not to adjust the volume

continuously upwards as your

hearing adapts.

• Do not turn up the volume so high

that you can’t hear what’s around

you.

• You should use caution or

temporarily discontinue use in

potentially hazardous situations.

• Excessive sound pressure from

earphones and headset can cause

hearing loss.

• Using headset with both ears

covered while driving is not

recommended and may be illegal in

some areas while driving.

• For your safety, avoid distractions

from music or phone calls while in

trac or other potentially dangerous

environments.

General information

To avoid damage or malfunction:

Caution

• Do not expose headset to excessive heat.

• Do not drop your headset.

• Headset shall not be exposed to dripping or

splashing.

• Do not allow your headset to be submerged

in water.

• Do not use any cleaning agents containing

alcohol, ammonia, benzene, or abrasives.

• If cleaning is required use a soft cloth, if

necessary dampened with a minimum amount

of water or diluted mild soap, to clean the

product.

• The integrated battery shall not be exposed

to excessive heat such as sunshine, re or the

like.

• Danger of explosion if battery is incorrectly

replaced. Replace only with the same or

equivalent type.

About operating and storage

temperatures and humidity

• The storage temperature is between

-15°C to 55 °C. The operation

temperature is 45°C (max.) (up to

90% relative humidity).

• Battery life may be shorter in high or

low temperature conditions.

3EN

2 Your

Bluetooth

wireless

headset

Congratulations on your purchase, and

welcome to Philips! To fully benet

from the support that Philips oers,

com/welcome.

With this Philips wireless headset, you

can:

• enjoy convenient wireless

handsfree calls;

• enjoy and control wireless music;

• switch between calls and music.

What's in the box

Philips True Wireless headset BASS+

SHB4385

Replaceable rubber ear caps x 2 pairs

Charging case

USB charging cable (for charging only)

Quick start guide

Other devices

A mobile phone or device (e.g.

notebook, PDA, Bluetooth adapters,

MP3 players etc) which supports

Bluetooth and is compatible to the

headset (see ‘Technical data” on page

9).

Overview of your

Bluetooth wireless

headset

a Multi-function buttons

b LED indicator

c Micro USB charging slot

5EN

3 Get started

Charge the battery

Note

• Before you use your headset/charging case for

the rst time, charge the battery for 5 hours for

optimum battery capacity and lifetime.

• Use only the original USB charging cable to

avoid any damage.

• Finish your call before charging the headset,

as connecting the headset for charging will

power the headset o.

Charging case

Connect one end of the USB cable into

the charging case, and another end into

the power source.

» The charging case starts charging.

• When the charging case is charging,

a white LED light will be displayed.

• When the charging case is fully

charged, the white light goes o.

Headset

Place the headset on the charging case.

» The headset start charging.

• When the headset is charging, a

white LED light will be displayed.

• When the headset is fully charged,

the white light goes o.

Tip

• Normally, a full charge takes 2 hours (for the

headset or charging case).

Pair between both sides

of the headset

Make sure that the headset is fully

charged.

Press and hold the multi-function

buttons on both sides of the

headset for 2 seconds.

» The white LED lights on both

side of the headset ash 3 times.

» Both sides of the headset are

connected automatically.

» The headset is ready to pair with

the Bluetooth device.

Pair your headset with

the Bluetooth device

Turn on the Bluetooth function of

your mobile phone.

Pair the headset with the mobile

phone. For detailed information,

refer to the user manual of your

mobile phone.

Tip

• The headset stores the last 2 devices in the

memory. If you try to pair more than 2 devices,

the earliest paired device is replaced by the

new one.

The following example shows you how

to pair the headset with your mobile

phone.

Activate the Bluetooth feature

of your mobile phone, select

Philips SHB4385.

Enter the headset password "0000"

(4 zeros) if prompted. For those

mobile phones featuring Bluetooth

3.0 or higher, no need to enter a

password.

Philips SHB4385

SHB4405

7EN

4 Use your

headset

Connect the headset to a

Bluetooth device

Turn on your mobile

phone/Bluetooth device.

Press and hold the multi-function

buttons on both sides of the

headset for 2 seconds.

» The white LED lights on both

sides of the headset ash 3

times.

» Both sides of the headset are

connected automatically.

» The headset is reconnected

to the last connected mobile

phone/Bluetooth device

automatically. If the last one is

not available, the headset tries

to reconnect to the second last

connected device.

Tip

• If you turn on the mobile phone/Bluetooth

device or activate the Bluetooth feature after

turning on the headset, you have to reconnect

the headset and mobile phone/Bluetooth

device manually.

Note

• If the headset fails to connect to any

Bluetooth device within 5 minutes, it will

switch o automatically to save the battery life.

Power on/o

Task Multi-

function

button

Operation

Turn the

headset on.

Right and

left head-

set

Press and

hold for 2

seconds.

Turn the

headset o.

Right and

left head-

set

Press and

hold for 3

seconds.

» The

white

LED

ashes

for 3

times.

Manage your calls and

music

Music control

Task Multi-

function

button

Operation

Play or pause

music.

Right

headset

Press once.

Volume up Left

headset

Press twice.

Volume down Left

headset

Press once.

Skip forward. Right

headset

Press twice.

Skip

backward.

Right

headset

Press 3

times..

Call control

Task Multi-

function

button

Operation

Pick up/hang

up a call.

Right

headset

Press once.

» 1 beep.

Reject an

incoming call.

Right

headset

Press and

hold for 1

second.

» 1 beep.

Switch caller

during a call.

Right

headset

Press twice.

Voice control

Task Multi-

function

button

Operation

Siri/Google

Now.

Right

headset

Press twice

and hold for 1

second.

LED indicator status

Headset status Indicator

The headset is

connected to a

Bluetooth device,

while the headset

is in standby

mode or while

you are listening

to music.

The blue LED

ashes for every 5

seconds.

The headset is

ready for pairing.

The white LED

ashes 3 times.

The headset

is on but not

connected to a

Bluetooth device.

The blue LED

ashes for every 5

seconds.

If no connection

can be made, the

headset will turn

itself o within 5

minutes.

Low battery level

(headset).

You will hear

“battery low” on

the headset.

Low battery level

(charging case).

The red LED on

the charging case

ashes every 1

second.

Battery is

fully charged

(headset).

The white LED on

the headset is o.

Battery is fully

charged (charging

case).

The white LED on

the charging case

is o.

How to wear

1 2

9EN

5 Technical

data

Headset

• Music time: 6 hours (additional 6

hrs with charging case)

• Talk time: 6 hours (additional 6 hrs

with charging case)

• Standby time: 200 hours

• Charging Time: 2 hours

• Normal time for a full charge: 2

hours

• Rechargeable lithium ion battery:

(105mAh)

• Bluetooth 4.2, Bluetooth mono

support (Headset Prole - HSP,

Hands-Free Prole - HFP),

Bluetooth stereo supported

(Advanced Audio Distribution

Prole - A2DP; Audio Video Remote

Control Prole - AVRCP)

• Support audio codec (SBC)

• Frequency range: 2.402-2.480GHz

• Transmitter power: <20dBm

• Operating range: Up to 10 meters

(33 feet)

• Digital echo & noise reduction

• Auto power o

Charging case

• Charging time: 2 hrs

• Rechargeable Li-ion battery : 350

mAh

• Number of recharges supported: 1

Note

• Specications are subject to change without

notice.

6 Notice

Declaration of conformity

Hereby, Gibson Innovations declares

that this product is in compliance

with the essential requirements

and other relevant provisions of

Directive 2014/53/EU. You can nd the

Declaration of Conformity on www.p4c.

philips.com.

Disposal of your old

product and battery

Your product is designed and

manufactured with high quality

materials and components, which can

be recycled and reused.

This symbol on a product means that

the product is covered by European

Directive 2012/19/EU.

This symbol means that the product

contains a built-in rechargeable

battery covered by European Directive

2013/56/EU which cannot be disposed

of with normal household waste. We

strongly advise you to take your product

to an ocial collection point or a Philips

service centre to have a professional

remove the rechargeable battery.

Inform yourself about the local separate

collection system for electrical and

electronic products and rechargeable

batteries. Follow local rules and

never dispose of the product and

rechargeable batteries with normal

household waste. Correct disposal of

old products and rechargeable batteries

helps prevent negative consequences

for the environment and human health.

Remove the integrated battery

If there is no collection/recycling system

for electronic products in your country,

you can protect the environment by

removing and recycling the battery

before disposing the headset.

• Make sure the headset is

disconnected from the charging

case before removing the battery.

• Make sure the charging case is

disconnected from the USB charging

cable before removing the battery.

Compliance with EMF

This product complies with all applicable

standards and regulations regarding

exposure to electromagnetic elds.

Environmental information

All unnecessary packaging has been

omitted. We have tried to make the

packaging easy to separate into three

materials: cardboard (box), polystyrene

foam (buer) and polyethylene (bags,

protective foam sheet.)

Your system consists of materials

which can be recycled and reused if

disassembled by a specialized company.

Please observe the local regulations

regarding the disposal of packaging

materials, exhausted batteries and old

equipment.

Trademarks

Bluetooth

The Bluetooth® word mark and logos

are registered trademarks owned by

Bluetooth SIG, Inc. and any use of such

marks by Gibson Innovations Limited is

under license.

Siri

Siri is a trademark of Apple Inc., registered

the U.S. and other countries.

Google

Google and the Google Logo are

registered trademarks of Google Inc.

7 Frequently

asked

questions

My Bluetooth headset does not switch

on.

The battery level is low. Charge the

headset.

I cannot pair my Bluetooth headset

with a mobile phone.

The Bluetooth is disabled. Enable

the Bluetooth feature on your mobile

phone and turn on the mobile phone

before you turn on the headset.

Pairing does not work.

Make sure the headset is in pairing

mode.

• Follow the steps described in this

user manual (see ‘Pair your headset

with the Bluetooth device” on page

6).

Make sure the left and right sides of the

headset are successfully connected.

• Make sure that the white LED lights

on both side of the headset ash 3

times.

If there is still pairing issue, power o the

headset. Then power on the headset

and repeat the pairing procedure.

The mobile phone cannot nd the

headset.

• The headset may be connected to a

previously paired device. Turn o the

connected device or move it out of

range.

• Pairing may have been reset or the

headset has been previously paired

with another device. Pair the headset

with the mobile phone again as

described in the user manual (see

‘Pair your headset with the Bluetooth

device” on page 6).

My Bluetooth headset is connected to a

Bluetooth stereo enabled mobile phone,

but music only plays on the mobile

phone speaker.

Refer to the user manual of your mobile

phone. Select to listen to music through

the headset.

The audio quality is poor and crackling

noise can be heard.

The Bluetooth device is out of range.

Reduce the distance between your

headset and Bluetooth device, or remove

obstacles between them.

The audio quality is poor when streaming

from the mobile phone is very slow, or

audio streaming does not work at all.

Make sure your mobile phone not only

supports (mono) HSP/HFP but also

supports A2DP (see ‘Technical data” on

page 9).

I hear but cannot control music on my

Bluetooth device (e.g. play/pause/skip

forward/backward).

Make sure the Bluetooth audio source

supports AVRCP (see ‘Technical data” on

page 9).

The volume level of the headset is too

low.

Some Bluetooth devices cannot link the

volume level with the headset through

volume sync. In this case, you have to

adjust the volume on your Bluetooth

device and headset independently to

achieve an appropriate volume level.

How can I restore all original headset

settings?

When the headset is powered o,

press and hold the multifunction

button for 10 seconds.

» You will hear doo-doo sound.

The headset is o

Remove the old device name on

the headset.

Power on the headset.

» The headset will enter the

pairing mode again.

Pair between both sides of the

headset (see ‘Pair between both

sides of the headset” on page

5).

Pair your headset with the

Bluetooth device (see ‘Pair your

headset with the Bluetooth device”

on page 6).

For further support, visit www.philips.

com/support.

This product has been manufactured by, and is sold

under the responsibility of Gibson Innovations Ltd., and

Gibson Innovations Ltd. is the warrantor in relation to

this product.

Philips and the Philips Shield Emblem are registered trademarks of Koninklijke

Philips N.V. and are used under license

UM_SHB4385_00_EN_V0.2

WK1732

English:

Notice of compliance

The device complies with the FCC rules, Part 15. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference that may cause undesired

operation.

FCC rules

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of

the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instruction manual, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by one or more of the following measures:

 Relocate the receiving antenna.

 Increase the separation between equipment and receiver.

 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

 Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Canada:

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following

Two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

CAN ICES-3(B)/NMB-3(B)

IC Radiation Exposure Statement:

This equipment complies with Canada radiation exposure limits set forth for uncontrolled environments.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for

compliance could void the user's authority to operate the equipment.

Model: SHB4385

FCC ID: 2AANUSHB4385

ISED Cerification Number: 11260A-SHB4385

This equipment should be installed and operated with a minimum distance of 5 millimeters between

the radiator and your body.

The RF exposure complicance distance is 5 millimeters.

French:

Avis de conformité

Cet appareil satisfait aux règlements de la FCC partie 15 du Code of Federal Regulations. Son fonctionnement est

assujetti aux deux conditions suivantes :

1. Cet appareil ne doit pas causer d’interférence préjudiciable et

2. l’appareil doit accepter toute interférence reçue, y compris les interférences qui peuvent causer un

fonctionnement non désiré.

Règlement de la FCC

Cet équipement a été testé et jugé compatible avec les limites s’appliquant aux appareils numériques de la classe B,

conformément à l’article 15 du règlement de la FCC. Ces limites ont été définies pour fournir une protection

raisonnable contre les interférences nuisibles dans le cadre d’une installation résidentielle. Cet équipement génère,

utilise et peut émettre de l’énergie radiofréquence et, s’il n’est pas installé ni utilisé conformément aux instructions,

peut causer des interférences gênantes pour les communications radio.

Rien ne garantit toutefois que des interférences ne surviendront pas dans une installation particulière. Si cet

équipement cause des interférences nuisibles pour la réception de la radio ou de la télévision, ce qui peut être

déterminé en mettant l’équipement hors tension puis sous tension, l’utilisateur devra essayer de corriger ces

interférences en effectuant une ou plusieurs des opérations suivantes :

Déplacez l’antenne de réception.

Augmentez la distance entre l’équipement et le récepteur.

Branchez l’équipement à une prise d’un circuit autre que celui sur lequel le récepteur est branché.

Consultez le détaillant ou un technicien de radiotélévision expérimenté.

Canada :

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.

L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2)

l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en

compromettre le fonctionnement.

CAN ICES-3(B)/NMB-3(B)

Déclaration d’IC sur l’exposition aux radiations:

Cet équipement est conforme aux limites d’exposition aux radiations définies par le Canada pour des

environnements non contrôlés.

Cet émetteur ne doit pas être installé au même endroit ni utilisé avec une autre antenne ou un autre

émetteur.

radiateur et votre corps.

Cet équipement devrait être installé et actionné avec une distance minimum de 5 millimètres entre le

La distance de conformité à l'exposition RF est de 5 millimètres

Philips 2AANUSHB4385 Manuel utilisateur

Marque: Philips

Modèle: 2AANUSHB4385

Catégorie: Casques mobiles

Taper: Manuel utilisateur

Ce manuel convient également à

BASS+ SHB4385

Télécharger le PDF

rapport

dans d''autres langues

English: Philips 2AANUSHB4385 User manual

Philips 2AANUSHB4385 Manuel utilisateur

Ce manuel convient également à

Philips 2AANUSHB4385 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents