Chamberlain 8360 Manuel utilisateur

Marque: Chamberlain

Modèle: 8360

Catégorie: Porte de garage

Taper: Manuel utilisateur

Ce manuel convient également à

PREMIUM Series Garage Door Opener

MODELS 8355 • 8360 • 8365-267

USER’S GUIDE

• Please read this guide and the enclosed safety materials carefully!

• The door WILL NOT CLOSE unless the Protector System

is connected and properly aligned.

• Periodic checks of the garage door opener are required to ensure

safe operation.

• This garage door opener is ONLY compatible with MyQ

and Security+ 2.0

accessories.

• DO NOT enable the Timer-to-Close feature if you are installing the

garage door opener on a one-piece door. The Timer-to-Close is to

be used ONLY with sectional doors.

• Attach enclosed warning labels to the location indicated on label.

FOR RESIDENTIAL USE ONLY

LiftMaster

845 Larch Avenue

Elmhurst, Illinois 60126-1196

LiftMaster.com

updates and offers from LiftMaster

Take a photo of the camera icon

including the points ( ).

Send it in by texting

the photo to 71403 (US)

or visit www.liftmaster.photo (Global)

Contents

Important Safety Instructions ............................3-4

Operation...................................................... 5

Using the Door Control .................................. 6

Programming-Door Control Panel ..................... 7

Programming - Remote Controls....................... 8

To Erase the Memory .................................... 8

To Open the Door Manually ............................. 9

Battery Backup* .......................................... 9

Adjustment ...................................................10

Program the Travel ......................................11

Test the Safety Reversal System ......................12

Test the Protector System

............................12

Maintenance .................................................13

Troubleshooting .........................................14-15

Repair Parts .................................................16

Warranty .....................................................17

Registration..................................................18

Safety Symbol and Signal Word

Review

This garage door opener has been designed and tested

to offer safe service provided it is installed, operated,

maintained and tested in strict accordance with the

instructions and warnings contained in this manual.

When you see these Safety Symbols and Signal

Words on the following pages, they will alert you to

the possibility of serious injury or death if you do not

comply with the warnings that accompany them. The

hazard may come from something mechanical or from

electric shock. Read the warnings carefully.

Mechanical

Electrical

When you see this Signal Word on the following pages, it

will alert you to the possibility of damage to your garage

door and/or the garage door opener if you do not comply

with the cautionary statements that accompany it. Read

them carefully.

Serial Number:

Date of Purchase:

Write down the following information

for future reference:

The images throughout this manual are for reference and your product may look different.

CONTACT INFORMATION

Leave this Users Guide with the homeowner.

*If applicable.

IMPORTANT INSTALLATION INSTRUCTIONS

To reduce the risk of SEVERE INJURY or DEATH:

WARNING

1. READ AND FOLLOW ALL WARNINGS AND

INSTRUCTIONS.

2. Install garage door opener ONLY on properly

balanced and lubricated garage door. An

improperly balanced door may NOT reverse when

required and could result in SEVERE INJURY or

DEATH.

3. ALL repairs to cables, spring assemblies and

other hardware MUST be made by a trained door

systems technician BEFORE installing opener.

4. Disable ALL locks and remove ALL ropes

connected to garage door BEFORE installing

opener to avoid entanglement.

5. Install garage door opener 7 feet (2.13 m) or

more above ﬂ oor.

6. Mount the emergency release within reach, but at

least 6 feet (1.83 m) above the ﬂ oor and avoiding

contact with vehicles to avoid accidental release.

7. NEVER connect garage door opener to power

source until instructed to do so.

8. NEVER wear watches, rings or loose clothing

while installing or servicing opener. They could

be caught in garage door or opener mechanisms.

9. Install wall-mounted garage door control:

• within sight of the garage door.

• out of reach of children at minimum height of

5 feet (1.5 m).

• away from ALL moving parts of the door.

10. Place entrapment warning label on wall next to

garage door control.

11. Place manual release/safety reverse test label in

plain view on inside of garage door.

12. Upon completion of installation, test safety

reversal system. Door MUST reverse on contact

with a 1-1/2" (3.8 cm) high object (or a 2x4 laid

ﬂ at) on the ﬂ oor.

13. To avoid SERIOUS PERSONAL INJURY or

DEATH from electrocution, disconnect ALL

electric and battery power BEFORE performing

ANY service or maintenance.

14. DO NOT enable the Timer-to-Close functionality

if operating either one-piece or swinging garage

doors. To be enabled ONLY when operating a

sectional door.

15.

SAVE THESE

INSTRUCTIONS.

Important Safety Instructions

NOTE: For complete installation instructions visit LiftMaster.com to print the entire owner’s manual.

Important Safety Instructions

IMPORTANT SAFETY INSTRUCTIONS

To reduce the risk of SEVERE INJURY or DEATH:

WARNING

1. READ AND FOLLOW ALL WARNINGS AND

INSTRUCTIONS.

2. ALWAYS keep remote controls out of reach of

children. NEVER permit children to operate or

play with garage door control push buttons or

remote controls.

3. ONLY activate garage door when it can be seen

clearly, it is properly adjusted, and there are no

obstructions to door travel.

4. ALWAYS keep garage door in sight and away

from people and objects until completely closed.

NO ONE SHOULD CROSS THE PATH OF THE

MOVING DOOR.

5. NO ONE SHOULD GO UNDER A STOPPED,

PARTIALLY OPENED DOOR.

6. If possible, use emergency release handle to

disengage trolley ONLY when garage door is

CLOSED. Use caution when using this release

with the door open. Weak or broken springs or

unbalanced door could result in an open door

falling rapidly and/or unexpectedly and increasing

the risk of SEVERE INJURY or DEATH.

7. NEVER use emergency release handle unless

garage doorway is clear of persons and

obstructions.

8. NEVER use handle to pull garage door open or

closed. If rope knot becomes untied, you could

fall.

9. After ANY adjustments are made, the safety

reversal system MUST be tested.

10. Safety reversal system MUST be tested every

month. Garage door MUST reverse on contact

with 1-1/2" high (3.8 cm) object (or a 2x4 laid

ﬂ at) on the ﬂ oor. Failure to adjust the garage

door opener properly increases the risk of

SEVERE INJURY or DEATH.

11. ALWAYS KEEP GARAGE DOOR PROPERLY

BALANCED. An improperly balanced door may

NOT reverse when required and could result in

SEVERE INJURY or DEATH.

12. ALL repairs to cables, spring assemblies

and other hardware, ALL of which are under

EXTREME tension, MUST be made by a trained

door systems technician.

13. ALWAYS disconnect electric power to garage

door opener BEFORE making ANY repairs or

removing covers.

14. This operator system is equipped with an

unattended operation feature. The door could

move unexpectedly. NO ONE SHOULD CROSS

THE PATH OF THE MOVING DOOR.

15. DO NOT enable the Timer-to-Close functionality

if operating either one-piece or swinging garage

doors. To be enabled ONLY when operating a

sectional door.

16.

SAVE THESE

INSTRUCTIONS.

Operation

Your garage door opener is equipped with features to

provide you with greater control over your garage door

operation. Accessories provided with your garage door

opener will vary depending on the garage door opener

model purchased.

ALERT2CLOSE

The Alert2Close feature provides a visual and an audible

alert that an unattended door is closing.

TIMER-TO-CLOSE (TTC)

The Timer-to-Close feature automatically closes the door

after a speciﬁ ed time period that can be adjusted using

a TTC enabled door control (Models 881LM or 880LM).

Prior to and during the door closing the garage door

opener lights will ﬂ ash and the garage door opener will

beep.

MyQ

technology uses a 900MHz signal to provide two-

way communication between the garage door opener and

MyQ

enabled accessories. Your garage door opener is

compatible with up to 16 MyQ

accessories.

REMOTE CONTROLS AND DOOR CONTROLS

(SECURITY+ 2.0

)

Your garage door opener has already been programmed

at the factory to operate with your remote control, which

changes with each use, randomly accessing over 100

billion new codes. Compatible with MyQ

and

Security+ 2.0

NOTE: Older LiftMaster remote controls, door controls,

and third party products are not compatible.

Accessories

(Security+ 2.0

)

MEMORY CAPACITY

Remote Controls Up to 24

Door Controls Up to 2 Smart Control Panels or 4

of any other Security+ 2.0

door

controls

Keyless Entries Up to 2

THE PROTECTOR SYSTEM

(SAFETY REVERSING

SENSORS)

When properly connected and aligned, the safety

reversing sensors will detect an obstruction in the path

of the infrared beam. If an obstruction breaks the infrared

beam while the door is closing, the door will stop and

reverse to full open position, and the opener lights will

ﬂ ash 10 times. If the door is fully open, and the safety

reversing sensors are not installed, or are misaligned,

the door will not close from a remote control. However,

you can close the door if you hold the button on the door

control or keyless entry until the door is fully closed. The

safety reversing sensors do not affect the opening cycle.

ENERGY CONSERVATION

For energy efﬁ ciency the garage door opener will enter

sleep mode when the door is fully closed. The sleep mode

shuts the garage door opener down until activated. The

sleep mode is sequenced with the garage door opener

light bulb; as the light bulb turns off the sensor LEDs will

turn off and whenever the garage door opener lights turn

on the sensor LEDs will light.

LIGHTS

The garage door opener light bulbs will turn on when

the opener is initially plugged in; power is restored after

interruption, or when the garage door opener is activated.

The lights will turn off automatically after 4-1/2 minutes.

An incandescent A19 light bulb (100 watt maximum) or

for maximum energy efﬁ ciency a 26W (100W equivalent)

compact ﬂ uorescent light (CFL) bulb may be used.

Light Feature

The garage door opener is equipped with an added

feature; the lights will turn on when someone enters

through the open garage door and the safety reversing

sensor infrared beam is broken. For added control over

the light bulbs on your garage door opener, see page 7.

USING YOUR GARAGE DOOR OPENER

The garage door opener can be activated through a wall-

mounted door control, remote control, wireless keyless

entry or MyQ

accessory. When the door is closed and

the garage door opener is activated the door will open.

If the door senses an obstruction or is interrupted while

opening the door will stop. When the door is in any

position other than closed and the garage door opener is

activated the door will close. If the garage door opener

senses an obstruction while closing, the door will reverse.

If the obstruction interrupts the sensor beam the garage

door opener lights will blink 10 times. However, you can

close the door if you hold the button on the door control

or keyless entry until the door is fully closed. The safety

reversing sensors do not affect the opening cycle. The

safety reversing sensor must be connected and aligned

correctly before the garage door opener will move in the

down direction.

Operation

Using the Door Control

PUSH BAR

Press the push bar to open and close the door.

LIGHT BUTTON

Press the LIGHT button to turn the garage door opener

lights on or off. When the lights are turned on they will

stay on until the LIGHT button is pressed again, or until

the garage door opener is activated. Once the garage

door opener is activated the lights will turn off after the

speciﬁ ed period of time (the factory setting is 4-1/2

minutes). The LIGHT button will not control the lights

when the door is in motion. The duration of the light

timing can be adjusted using the door control, see

page 7.

The following features are accessible by lifting the

push bar:

LEARN A DEVICE

Any compatible remote controls, wireless keyless entry,

or MyQ

accessories can be programmed to the garage

door opener by pressing the Learn button.

LOCK

The LOCK feature is designed to prevent activation of

the garage door opener from remote controls while still

allowing activation from the door control and keyless

entry. This feature is useful for added peace of mind

when the home is empty (i.e. vacation).

AUTOMATIC LIGHT

Motion Sensor (Motion-Detecting Control Panel)

Factory default is set to on. This feature automatically

turns on the garage door opener lights when motion

is sensed. The lights will come on for the set period of

time, then shut off. If using the garage door opener light

as a work light disable the motion sensor, otherwise

the light will turn off automatically if you are beyond the

range of the sensor.

Light Feature

The lights will turn on when someone enters through

the open garage door and the safety reversing sensor

infrared beam is broken.

MAINTENANCE ALERT SYSTEM (MAS)

This feature assists the homeowner in ensuring the

garage door opener system stays in good working

condition. When the garage door opener needs to be

serviced (approximately 4500 garage door opener

cycles) the command (yellow) and service (red) LEDs

will begin to alternately ﬂ ash back and forth. The factory

setting for the MAS feature is off and can be activated

at time of installation. Contact your installing dealer for

service.

Push Bar

Light Button

MOTION-DETECTING CONTROL PANEL

The control panel will vary depending on the garage door opener

model purchased.

MULTI-FUNCTION CONTROL PANEL

Service LED

LEARN Button

LOCK Button

Light Button

Service LED

Push Bar

LEARN Button

LOCK Button

Command LED

SYNCHRONIZE THE DOOR CONTROL

To synchronize the door control to the garage door

opener, press the push bar until the garage door

opener activates (it may take up to 3 presses). Test the

door control by pressing the push bar, each press of

the push bar will activate the garage door opener.

Service

LED

LEARN

Button

LEARN

Button

LOCK

Button

LOCK

Button

Motion

Sensor

Operation

Features

Lock NOTE: Your remote controls will NOT work when LOCK mode is active however your keyless

entry will still allow access to your garage.

Activate: Press and hold the LOCK button for 2 seconds. The command LED will ﬂ ash as long

as the lock feature is activated and your handheld remote control will not operate your door at

this time.

Deactivate: Press and hold the LOCK button again for 2 seconds. The command LED will stop

ﬂ ashing and normal operation will resume.

Light To change the amount of time the garage door opener lights will stay on:

Press and hold the LOCK button until the garage door opener lights ﬂ ash.* The time interval is

indicated by the number of ﬂ ashes.

To cycle through the time intervals repeat the step above.

Deactivate: Press and hold the LIGHT button until the garage door opener lights turn on, then

off again.*

Activate: Start with the garage door opener lights on. Press and hold the LIGHT button until the

garage door opener lights turn off, then on again.*

* Approximately 10 seconds

Motion Sensor

(Motion-Detecting

Control Panel)

Activate/Deactivate: Slide the motion sensor switch ON or OFF.

To Program a

Remote Control

or Keyless Entry

1. Press the LEARN button on the door control to enter Programming Mode.

2. Press the LEARN button again, the LED will ﬂ ash once.

3. Remote Control: Press the button on the remote control that you wish to operate your garage

door.

Keyless Entry: Enter a 4-digit personal identiﬁ cation number (PIN) of your choice on the

keyless entry keypad. Then press the ENTER button.

The garage door opener lights will ﬂ ash (or two clicks will be heard) when the code has been

programmed. If programming is unsuccessful, repeat steps 1-3 or program the remote using

the learn button on the garage door opener.

Maintenance

Alert System

(MAS)

Activate/Deactivate

Press and hold the LEARN button. Then press the LIGHT button. The service LED will ﬂ ash the

status; Active is 2 ﬂ ashes and deactivated is 3 ﬂ ashes.

NUMBER OF TIMES GARAGE DOOR OPENER LIGHTS FLASH 1234

TIME THE GARAGE DOOR OPENER LIGHT STAYS ON 1 ½

Minutes

2 ½

Minutes

3 ½

Minutes

4 ½

Minutes

Motion Sensor

Switch

Command

LED

Service

LED

LIGHT

Button

LIGHT

Button

Command LED

MULTI-FUNCTION CONTROL PANELMOTION-DETECTING CONTROL PANEL

Programming - Door Control Panel

Operation

1 Press and release the Learn button on the garage

door opener. The Learn indicator light will glow

steadily for 30 seconds.

PROGRAM A REMOTE USING THE LEARN BUTTON ON THE GARAGE DOOR OPENER

When replacing the light lens cover, ensure the antenna wires are hanging straight down.

Learn

Indicator

Light

Yellow

Learn

Button

Your garage door opener has been programmed at the factory to operate with your remote control. Older LiftMaster

remote controls are NOT compatible. Programming can be done through the door control or the Learn button on the

garage door opener. To program additional remote controls refer to the instructions provided with the additional remote

controls or visit LiftMaster.com. If your vehicle is equipped with a Homelink

, you may require an external adapter

depending on the make, model, and year of your vehicle. Visit www.homelink.com for additional information.

ERASE ALL REMOTE CONTROLS AND KEYLESS ENTRIES

1 Press and hold the learn button on garage door opener until the learn LED goes out (approximately 6 seconds). All

remote control and keyless entry codes are now erased.

Reprogram any accessory you wish to use.

ERASE ALL DEVICES (Including MyQ

enabled accessories)

1 Press and hold the learn button on garage door opener until the learn LED goes out (approximately 6 seconds).

2 Immediately press and hold the learn button again until the learn LED goes out. All codes are now erased.

Reprogram any accessory you wish to use.

Programming - Remote Controls

To Erase the Memory

2 Within 30 seconds,

press and hold

the button on the

remote control.

3 Release the button when the

garage door opener light blinks.

It has learned the code. If light

bulbs are not installed, two clicks

will be heard.

DISCONNECT THE TROLLEY

1 The door should be fully

closed if possible.

2 Pull down on the emergency

release handle.

RECONNECT THE TROLLEY

The lockout feature prevents

the trolley from reconnecting

automatically.

1 Pull the emergency release

handle down and back

(toward the opener). The

door can then be raised and

lowered manually as often as

necessary.

2 To disengage the lockout feature, pull the handle

straight down.

The trolley will reconnect on the next UP or DOWN

operation, either manually or by using the door control or

remote control.

Operation

To prevent possible SERIOUS INJURY or DEATH from

a falling garage door:

• If possible, use emergency release handle to

disengage trolley ONLY when garage door is

CLOSED. Weak or broken springs or unbalanced

door could result in an open door falling rapidly

and/or unexpectedly.

• NEVER use emergency release handle unless

garage doorway is clear of persons and

obstructions.

• NEVER use handle to pull door open or closed. If

rope knot becomes untied, you could fall.

To Open the Door Manually

Battery Backup (If applicable)

The battery backup system allows access in and out of your garage, even when the power is out. When the garage door

opener is operating on battery power, the garage door opener will run slower, the light will not function, the Battery

Status LED will glow solid orange, and a beep will sound approximately every 2 seconds.

The battery charges when the garage door opener is plugged into a 110Vac electrical outlet that has power and

requires 24 hours to fully charge. A fully charged battery supplies 12Vdc to the garage door opener for one to two

days of normal operation during an electrical power outage. After the electrical power has been restored, the battery

will recharge within 24 hours. The battery will last approximately 1 to 2 years with normal usage. Instructions for

replacement are provided with the battery. To obtain maximum battery life and prevent damage, disconnect the battery

when the garage door opener is unplugged for an extended period of time.

NOTE: When the garage door opener is in battery backup mode the garage door opener lights, Timer-to-Close, and

Remote Close features are unavailable.

BATTERY STATUS LED

GREEN LED:

All systems are normal.

• A solid green LED light indicates the battery is fully

charged.

• A ﬂ ashing green LED indicates the battery is being

charged.

ORANGE LED:

The garage door opener has lost power and is in battery

backup mode.

• A solid orange LED with beep, sounding

approximately every 2 seconds, indicates the garage

door opener is operating on battery power.

• A ﬂ ashing orange LED with beep, sounding every 30

seconds, indicates the battery is low.

RED LED:

The garage door opener’s 12V battery needs to be

replaced.

• A solid red LED with beep, sounding every 30

seconds, indicates the garage door opener needs

servicing. Please call for replacement battery to allow

your system to operate during a power outage.

NOTE: The Battery Status LED is most visible with the

garage door opener light off. Battery does not have to be

fully charged to operate the garage door opener.

Battery Status LED

Adjustment

Introduction

Without a properly installed safety reversal system,

persons (particularly small children) could be

SERIOUSLY INJURED or KILLED by a closing garage

door.

• Incorrect adjustment of garage door travel limits

will interfere with proper operation of safety

reversal system.

• After ANY adjustments are made, the safety

reversal system MUST be tested. Door MUST

reverse on contact with 1-1/2" (3.8 cm) high object

(or 2x4 laid ﬂ at) on ﬂ oor.

To prevent damage to vehicles, be sure fully open

door provides adequate clearance.

Your garage door opener is designed with electronic

controls to make setup and adjustments easy. The

adjustments allow you to program where the door will

stop in the open (UP) and close (DOWN) position. The

electronic controls sense the amount of force required to

open and close the door.

NOTE: If anything interferes with the door’s upward

travel it will stop. If anything interferes with the door’s

downward travel, it will reverse.

To watch a short instructional video on programming

your new garage door opener use your smartphone to

read the QR Code below:

UP (Open) DOWN (Close)

PROGRAMMING BUTTONS

The programming buttons are located on the left side panel of the garage door opener and are used to program the travel.

UP Button

Adjustment

Button

DOWN Button

PROGRAMMING BUTTONS

Program the Travel

Without a properly installed safety reversal system, persons (particularly small children) could be SERIOUSLY

INJURED or KILLED by a closing garage door.

• Incorrect adjustment of garage door travel limits will interfere with proper operation of safety reversal system.

• After ANY adjustments are made, the safety reversal system MUST be tested. Door MUST reverse on contact with

1-1/2" (3.8 cm) high object (or 2x4 laid ﬂ at) on ﬂ oor.

Adjustment

1.1 Press and hold the

Adjustment Button

until the UP Button

begins to ﬂ ash and/or

a beep is heard.

1.2 Press and hold the UP Button until the door is

in the desired UP position.

NOTE: The UP and DOWN Buttons can be used to

move the door up and down as needed.

1.5 Once the door is in the

desired DOWN position

press and release the

Adjustment Button. The

garage door opener lights

will ﬂ ash twice and the UP

Button will begin to ﬂ ash.

1.6 Press and release the UP Button. When the door

travels to the programmed UP position, the

DOWN Button will begin to ﬂ ash.

1.7 Press and release the DOWN Button. The door

will travel to the programmed DOWN position.

Programming is complete.

* If the garage door opener lights are ﬂ ashing 5

times during the steps for Program the Travel, the

programming has timed out. If the garage door

opener lights are ﬂ ashing 10 times during the steps

for Program the Travel, the safety reversing sensors

are misaligned or obstructed. When the sensors are

aligned and unobstructed, cycle the door through a

complete up and down cycle using the remote control

or the UP and DOWN buttons. Programming is

complete. If you are unable to operate the door up and

down, repeat the steps for Program the Travel.

1.4 Press and hold the DOWN Button until the door

is in the desired DOWN position.

NOTE: The UP and DOWN Buttons can be used to

move the door up and down as needed.

1.3 Once the door is in the

desired UP position press

and release the Adjustment

Button. The garage door

opener lights will ﬂ ash

twice and the DOWN

Button will begin to ﬂ ash.

2.1 With the door fully open, place a 1-1/2 inch

(3.8 cm) board (or a 2x4 laid ﬂ at) on the ﬂ oor,

centered under the garage door.

Test the Safety Reversal System

2.2 Press the remote control push button to close

the door. The door MUST reverse when it makes

contact with the board.

If the door stops and does not reverse on the obstruction,

increase the down travel (see Adjustment Step 1).

Repeat the test. When the door reverses upon contact

with the 1-1/2 inch board, remove the board and open/

close the door 3 or 4 times to test the adjustment.

If the test continues to fail, call a trained door systems

technician.

Without a properly installed safety reversal system,

persons (particularly small children) could be

SERIOUSLY INJURED or KILLED by a closing garage

door.

• Safety reversal system MUST be tested every

month.

• After ANY adjustments are made, the safety reversal

system MUST be tested. Door MUST reverse on

contact with 1-1/2" high (3.8 cm) object (or 2x4 laid

ﬂ at) on the ﬂ oor.

Test the Protector System

3.1 Open the door. Place the garage door opener

carton in the path of the door.

The garage door opener will not close from a remote

control if the LED in either safety reversing sensor is off

(alerting you to the fact that the sensor is misaligned or

obstructed).

If the garage door opener closes the door when the

safety reversing sensor is obstructed (and the sensors

are no more than 6 inches [15 cm] above the ﬂ oor), call

for a trained door systems technician.

Without a properly installed safety reversing sensor,

persons (particularly small children) could be

SERIOUSLY INJURED or KILLED by a closing garage

door.

3.2 Press the remote control push button to close

the door. The door will not move more than

an inch (2.5 cm), and the garage door opener

lights will ﬂ ash 10 times.

Adjustment

To prevent possible SERIOUS INJURY or DEATH:

• NEVER allow small children near batteries.

• If battery is swallowed, immediately notify doctor.

To reduce risk of ﬁ re, explosion or chemical burn:

• Replace ONLY with 3V CR2032 coin batteries.

• DO NOT recharge, disassemble, heat above 212°F

(100°C) or incinerate.

The Remote Control Battery

Maintenance

EVERY MONTH

• Manually operate door. If it is unbalanced or binding,

call a trained door systems technician.

• Check to be sure door opens and closes fully. Adjust if

necessary, page 11.

• Test the safety reversal system. Adjust if necessary,

page 12.

EVERY YEAR

• Oil door rollers, bearings and hinges. The garage door

opener does not require additional lubrication. Do not

grease the door tracks.

• (If applicable) Test the battery backup and consider

replacing the battery to ensure the garage door opener

will operate during an electrical power outage.

Testing the Battery Backup:

1. Unplug the garage door opener. The battery

status LED will either glow solid orange indicating

opener is operating on battery power or will ﬂ ash

indicating low battery power.

2. Open and close the door using the remote control

or door control.

NOTE: The garage door opener may run slower

if the battery is not fully charged. The battery will

take 24 hours to fully charge.

3. Plug in the garage door opener. Verify the battery

status LED is ﬂ ashing green, indicating the

battery is charging.

EVERY TWO TO THREE YEARS

• Use a rag to wipe away the existing grease from the

garage door opener rail. Reapply a small layer of white

lithium grease to the top and underside of the rail

surface where the trolley slides.

The Lithium batteries should produce power for up to 5

years. If the battery is low, the remote control’s LED will

not ﬂ ash when the button is pressed. To replace battery,

pry open the case ﬁ rst in the middle (1), then at each

side (2 and 3) with the visor clip. Insert battery positive

side up.

Replace the batteries with only 3V CR2032 coin cell

batteries. Dispose of old batteries properly.

NOTICE: To comply with FCC and/or Industry Canada (IC) rules, adjustment or modiﬁ cations of this transceiver are prohibited. THERE ARE NO USER

SERVICEABLE PARTS. Any changes or modiﬁ cations not expressly approved by the party responsible for compliance could void the user’s authority to operate

the equipment.

This device complies with Part 15 of the FCC rules and IC RSS-210. Operation is subject to the following two conditions: (1) this device may not cause harmful

interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This Class B digital apparatus complies with Canadian ICES-003.

AVIS : Les règles de la FCC et/ou d’Industrie Canada (IC) interdisent tout ajustement ou toute modiﬁ cation de ce récepteur. IL N’EXISTE AUCUNE PIÈCE

SUSCEPTIBLE D’ÊTRE ENTRETENUE PAR L’UTILISATEUR. Tout changement ou toute modiﬁ cation non expressément approuvé par la partie responsable de

la conformité peut avoir pour résultat d’annuler l’autorité de l’utilisateur de faire fonctionner l’équipement.

Cet appareil est conforme aux dispositions de la partie 15 du règlement de la FCC et de la norme IC RSS-210. Son utilisation est assujettie aux deux conditions

suivantes : (1) ce dispositif ne peut causer des interférences nuisibles, et (2) ce dispositif doit accepter toute interférence reçue, y compris une interférence

pouvant causer un fonctionnement non souhaité.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

Troubleshooting

DIAGNOSTIC CODE SYMPTOM SOLUTION

Up arrow

Flash(es)

Down arrow

Flash(es)

The garage door opener

will not close and the

light bulbs ﬂ ash.

Safety sensors are not installed, connected, or wires

may be cut. Inspect sensor wires for a disconnected

or cut wire.

The garage door opener

will not close and the

light bulbs ﬂ ash.

There is a short or reversed wire for the safety

sensors. Inspect safety sensor wire at all staple and

connection points, replace wire or correct as needed.

The door control will not

function.

The wires for the door control are shorted or the door

control is faulty. Inspect door control wires at all

staple and connection points, replace wire or correct

as needed.

The garage door opener

will not close and the

light bulbs ﬂ ash.

Safety sensors are misaligned or were momentarily

obstructed. Realign both sensors to ensure both LEDs

are steady and not ﬂ ickering. Make sure nothing is

hanging or mounted on the door that would interrupt

the sensor’s path while closing.

Door moves 6-8" (15-20

cm) stops or reverses.

Manually open and close the door. Check for binding

or obstructions, such as a broken spring or door lock,

correct as needed. Check wiring connections at travel

module and at the logic board. Replace travel module

if necessary.

No movement, only a

single click.

Manually open and close the door. Check for binding

or obstructions, such as a broken spring or door lock,

correct as needed. Replace logic board if necessary.

Opener hums for 1-2

seconds no movement.

Manually open and close the door. Check for binding

or obstructions, such as a broken spring or door lock,

correct as needed. Replace motor if necessary.

Door coasts after it has

come to a complete stop.

Program travel to coasting position or have door

balanced by a trained door systems technician.

2 1-5 No movement, or sound. Replace logic board.

Unable to set the travel

or retain position.

Check travel module for proper assembly, replace if

necessary.

The battery status LED*

is constantly ﬂ ashing

green.

Battery backup* charging circuit error, replace the

logic board.

*If applicable.

Diagnostic Chart

Your garage door opener is programmed with self-diagnostic capabilities. The UP and DOWN arrows on the garage

door opener will ﬂ ash the diagnostic codes.

Diagnostic Chart

My garage door opener beeps:

The garage door opener can beep for several reasons:

• Garage door opener has been activated through a device

or feature such as Timer-to-Close, garage door monitor

or LiftMaster Internet Gateway, see page 5.

• Operating on battery power or the 12Vdc battery needs

to be replaced (if applicable), see pages 9 and 13.

My remote control will not activate the garage door:

• Verify the lock feature is not activated on the door

control.

• Reprogram the remote control.

• If the remote control will still not activate the door check

the diagnostic codes to ensure the garage door opener

is working properly.

My door will not close and the light bulbs blink on my

motor unit:

The safety reversing sensor must be connected and

aligned correctly before the garage door opener will move

in the down direction.

• Verify the safety sensors are properly installed, aligned

and free of any obstructions.

My garage door opener light(s) will not turn off when the

door is open:

The garage door opener is equipped with a feature that

turns the light on when the safety reversing sensors have

been obstructed or when the motion sensor on the door

control detects movement in the garage. These features

can be disabled using the door control, see page 7.

My neighbor’s remote control opens my garage door:

Erase the memory from your garage door opener and

reprogram the remote control(s).

My vehicle’s Homelink

is not programming to my

garage door opener:

Depending on the make, model, and year of your vehicle

an external adapter may be required. Visit

www.homelink.com for additional information.

Troubleshooting

DIAGNOSTIC CODE SYMPTOM SOLUTION

Up arrow

Flash(es)

Down arrow

Flash(es)

4 1-4

Door is moving stops or

reverses.

Manually open and close the door. Check for

binding or obstructions, such as a broken spring

or door lock, correct as needed. If the door is

binding or sticking contact a trained door systems

technician. If door is not binding or sticking attempt

to reprogram travel (refer to page 11).

Opener runs approximately

6-8" (15-20 cm), stops and

reverses.

Communication error to travel module. Check

travel module connections, replace travel module if

necessary.

The garage door opener

will not close and the light

bulbs ﬂ ash.

Safety sensors are misaligned or were momentarily

obstructed. Realign both sensors to ensure both

LEDs are steady and not ﬂ ickering. Make sure

nothing is hanging or mounted on the door that

would interrupt the sensor’s path while closing.

Repair Parts

NOTE: For additional parts not shown, visit

LiftMaster.com to download or print the full owner’s

manual. The images throughout this manual are for

reference and your product may look different.

DESCRIPTION

PART

NUMBER

1 Light Lens - Models 8360 and 8355 41A7562

Light Lens - Model 8365-267 108D79

2 Receiver Logic Board - Model 8360 45DCT

Receiver Logic Board - Models 8355 and

8365-267 45ACT

3A Travel Module - Model 8360

41A7114-7

3B Travel Module - Models 8355 and 8365-267

041D7742-7

4A Motor w/Travel Module - Model 8360

41D1739-1

4B Motor w/Travel Module - Model 8355

041A7442

4C Motor w/Travel Module - Model 8365-267

041D7440

5 3V CR2032 Lithium Battery (Remote

Control) 10A20

6 Backup Battery (if applicable)

485LM

7 Safety Sensor Kit with receiving and

sending sensors with 3 feet (.9 m)

2-conductor wire 41A5034

Warranty

LIFTMASTER

ONE YEAR LIMITED WARRANTY

LIFETIME MOTOR AND BELT* LIMITED WARRANTY

ONE YEAR LIMITED WARRANTY FOR THE BATTERY BACKUP SYSTEM*

LiftMaster (“Seller”) warrants to the first retail purchaser of this product, for the residence in which this product

is originally installed, that it is free from defects in materials and/or workmanship for a period of one year from

the date of purchase, except that the motor and belt* are warranted to be free from defects in materials and/or

workmanship for the lifetime of the product while you own your residence, and the Battery Backup System* is

warranted to be free from defects in materials and/or workmanship for a period of one year from the date of

purchase. The proper operation of this product is dependent on your compliance with the instructions regarding

installation, operation, and maintenance and testing. Failure to comply strictly with those instructions will void

this limited warranty in its entirety.

If, during the limited warranty period, this product appears to contain a defect covered by this limited warranty,

call 1-800-528-9131, toll free, before dismantling this product. You will be advised of disassembly and shipping

instructions when you call. Then send the product or component, pre-paid and insured, as directed to our service

center for warranty repair. Please include a brief description of the problem and a dated proof-of-purchase

receipt with any product returned for warranty repair. Products returned to Seller for warranty repair, which upon

receipt by Seller are confirmed to be defective and covered by this limited warranty, will be repaired or replaced

(at Seller’s sole option) at no cost to you and returned pre- paid. Defective parts will be repaired or replaced with

new or factory-rebuilt parts at Seller’s sole option. [You are responsible for any costs incurred in removing and/

or reinstalling the product or any component.]

ALL IMPLIED WARRANTIES FOR THE PRODUCT, INCLUDING BUT NOT LIMITED TO ANY IMPLIED

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN

DURATION TO THE APPLICABLE LIMITED WARRANTY PERIOD SET FORTH ABOVE FOR THE RELATED

COMPONENT(S), AND NO IMPLIED WARRANTIES WILL EXIST OR APPLY AFTER SUCH PERIOD. Some states

do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.

THIS LIMITED WARRANTY DOES NOT COVER NON-DEFECT DAMAGE, DAMAGE CAUSED BY IMPROPER

INSTALLATION, OPERATION OR CARE (INCLUDING, BUT NOT LIMITED TO ABUSE, MISUSE, FAILURE TO

PROVIDE REASONABLE AND NECESSARY MAINTENANCE, UNAUTHORIZED REPAIRS OR ANY ALTERATIONS

TO THIS PRODUCT), LABOR CHARGES FOR REINSTALLING A REPAIRED OR REPLACED UNIT, REPLACEMENT

OF CONSUMABLE ITEMS (E.G., BATTERIES IN REMOTE CONTROL TRANSMITTERS AND LIGHT BULBS), OR

UNITS INSTALLED FOR NON-RESIDENTIAL USE. THIS LIMITED WARRANTY DOES NOT COVER ANY

PROBLEMS WITH, OR RELATING TO, THE GARAGE DOOR OR GARAGE DOOR HARDWARE, INCLUDING BUT

NOT LIMITED TO THE DOOR SPRINGS, DOOR ROLLERS, DOOR ALIGNMENT OR HINGES. THIS LIMITED

WARRANTY ALSO DOES NOT COVER ANY PROBLEMS CAUSED BY INTERFERENCE. UNDER NO

CIRCUMSTANCES SHALL SELLER BE LIABLE FOR CONSEQUENTIAL, INCIDENTAL OR SPECIAL DAMAGES

ARISING IN CONNECTION WITH USE, OR INABILITY TO USE, THIS PRODUCT. IN NO EVENT SHALL SELLER’S

LIABILITY FOR BREACH OF WARRANTY, BREACH OF CONTRACT, NEGLIGENCE OR STRICT LIABILITY EXCEED

THE COST OF THE PRODUCT COVERED HEREBY. NO PERSON IS AUTHORIZED TO ASSUME FOR US ANY

OTHER LIABILITY IN CONNECTION WITH THE SALE OF THIS PRODUCT.

Some states do not allow the exclusion or limitation of consequential, incidental or special damages, so the

above limitation or exclusion may not apply to you. This limited warranty gives you specific legal rights, and you

may also have other rights, which vary from state to state.

*If applicable.

114A4414G

Registration

OR register online at

www.prodresgister.com/liftmaster

updates and offers from LiftMaster

Take a photo of the camera icon

including the points (

Send it in by texting

the photo to 71403 (US)

or visit www.liftmaster.photo (Global)

Ouvre-porte de garage de série PREMIUM

MODÈLES 8355 • 8360 • 8365-267

GUIDE DE L’UTILISATEUR

• Veuillez lire attentivement ce guide de même que la documentation de sécurité

incluse!

• La porte NE SE FERMERA PAS si le Système Protector

n’est pas branché et

réglé correctement.

• Des vérifications périodiques de l’ouvre-porte de garage sont requises pour

garantir un fonctionnement sécuritaire du dispositif.

• Cet ouvre-porte de garage est compatible UNIQUEMENT avec les accessoires

MyQ

et Security+ 2.0

• N’activez PAS la fonction de minuterie de fermeture si vous installez l’ouvre-

porte de garage sur une porte rigide. La minuterie de fermeture doit être utilisée

UNIQUEMENT sur les portes articulées.

• Apposer les étiquettes d’avertissement incluses à l’endroit indiqué sur l’étiquette.

POUR RÉSIDENCES SEULEMENT

LiftMaster

845 Larch Avenue

Elmhurst, Illinois 60126-1196

LiftMaster.com

Enregistrez votre ouvre-porte de garage pour recevoir des

mises à jour et des offres de LiftMaster

Prenez une photo de l’icône d’appareil-photo,

y compris les points ( ).

Envoyez la photo par message

textuel à 71403 (É.-U.)

ou allez à www.liftmaster.photo (mondial)

L’INFORMATION DE CONTACT

Laissez ce Guide de l’utilisateur au propriétaire.

Matières

Importantes Consignes de Sécurité .....................3-4

Fonctionnement .............................................. 5

Utilisation de la commande de porte ................... 6

Programmation - Panneau de commande

de portende ................................................. 7

Programmation - Télécommande ....................... 8

Pour effacer tous le codes ............................... 8

Ouverture manuelle de la porte ......................... 9

Pile de secours* ........................................... 9

Réglage ......................................................10

Programmation des courses ............................ 11

Essai du système d’inversion

de sécurité .................................................12

Essai du Protector System

............................. 12

Entretien......................................................13

Dépannage ...............................................14-15

Pièces de Rechange ........................................16

Garantie ...................................................... 17

Enregistrement ..............................................18

*S’il y a lieu.

Numéro de série :

Date d’achat :

Veuillez noter les renseignements

suivants pour référence ultérieure :

Revue des symboles de sécurité et

des mots de signalement

Cet ouvre-porte de garage a été conçu et mis à l’essai

dans le but d’offrir un service sûr à condition qu’il soit

installé, utilisé, entretenu et mis à l’essai en stricte

conformité avec les instructions et les avertissements

contenus dans le présent manuel.

Lorsque vous verrez ces symboles de sécurité et ces

mots de signalement sur les pages suivantes, ils vous

aviseront de la possibilité de blessures graves ou de

mort si vous ne vous conformez pas aux avertissements

qui les accompagnent. Le danger peut être de source

mécanique ou provenir d’un choc électrique. Lisez

attentivement les avertissements.

Mécanique

Électrique

ATTENTION

AVERTISSEMENT

ATTENTION

AVERTISSEMENT

ATTENTIONATTENTION

AVERTISSEMENT

Lorsque vous verrez ce mot de signalement sur les

pages suivantes, il vous avisera de la possibilité de

dommages à votre porte de garage ou ouvre-porte de

garage, ou les deux, si vous ne vous conformez pas aux

énoncés de mise en garde qui l’accompagnent. Lisez-les

attentivement.

Les illustrations de ce mode d’emploi ne servent qu’à titre de référence. Votre appareil peut avoir un aspect différent.

La page charge ...

Chamberlain 8360 Manuel utilisateur

Marque: Chamberlain

Modèle: 8360

Catégorie: Porte de garage

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Chamberlain 8360 User manual
português: Chamberlain 8360 Manual do usuário

Chamberlain 8360 Manuel utilisateur

Ce manuel convient également à

Chamberlain 8360 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents