Broan M1 Guide d'installation

Taper
Guide d'installation

Ce manuel convient également à

M1B, M1M & M5S Series
Downflow, Direct Vent (Sealed Combustion)
Forced Air Gas & Oil Furnaces
For installation in:
Manufactured Homes
Recreational Vehicles, Park Models, & Manufactured
Buildings
Modular Homes / Buildings
INSTALLATION INSTRUCTIONS
WARNING CAUTION
FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly could
result in serious injury or property damage.
Installation and service must be performed
by a qualified installer, service agency or the
gas supplier.
Do not store or use gasoline or other
flammable vapors and liquids in the vicinity
of this or any other appliance.
WHAT TO DO IF YOU SMELL GAS
Do not try to light any appliance.
Do not touch any electrical switch; do not
use any phone in your building.
Leave the building immediately.
Immediately call your gas supplier from a
neighbors phone. Follow the gas suppliers
instructions.
• If you cannot reach your gas supplier, call
the fire department.
HUD Manufactured Home Construction and
Safety Standards (3280.714) prohibit the use
of noncertified air conditioning or heat pump
equipment with this furnace. It is strongly
recommended that manufactured housing
air conditioning components from Nortek
Global HVAC be selected to provide a matched
system specifically designed to meet these
requirements.
The cutting, splicing or modifying of any
internal electrical wiring may void product
warranties and create a hazardous condition.
Failure to comply with these standards could
also provide inadequate heating or cooling
performance and cause structural damage to
a manufactured home.
Please contact your local distributor for help.
A directory of Nortek Global HVAC factory
authorized servicers is located in the furnace
homeowner packet.
Reference: HUD Manufactured Home
Construction and Safety Standards 3280.714.
DO NOT DESTROY. PLEASE READ CAREFULLY & KEEP IN A SAFE PLACE FOR FUTURE REFERENCE.
2
TABLE OF CONTENTS
IMPORTANT SAFETY INFORMATION ..................... 3
REQUIREMENTS & CODES ..................................... 3
GENERAL INFORMATION ........................................ 4
Minimum Clearances ............................................... 4
Applications ............................................................. 4
Unit Location ............................................................ 6
CIRCULATING AIR REQUIREMENTS ...................... 6
Return Air ................................................................. 6
Supply Air ................................................................ 6
FURNACE INSTALLATION ....................................... 7
General Information ................................................. 7
Locating & Cutting Duct Openings ........................... 7
Standard Duct Connector Installation ...................... 9
Alternate Attachment Method ................................ 9
Round Duct Connector Installation .......................... 9
Installing the Furnace .............................................. 9
ROOF JACK INSTALLATION ................................... 10
Roof Jack Selection ................................................. 10
Locating & Cutting Roof / Ceiling Openings ............ 10
Installing The Roof Jack .......................................... 11
Installation of Transit-Mode Venting System ........... 11
Before home is moved to site .................................. 11
Installation of Transit-Mode Venting System ........... 12
After home is moved to site ..................................... 12
ELECTRICAL INFORMATION .................................. 13
Line Voltage Wiring .................................................. 13
Connecting Power Supply Wires ........................... 13
Low Voltage Wiring .................................................. 13
Connecting Thermostat Wires ............................... 13
Verifying Anticipator Setting .................................. 13
Grounding ................................................................ 14
FUEL SUPPLY & PIPING .......................................... 15
Leak Check .............................................................. 15
Flue Gas Sampling .................................................. 16
High Altitude Conversion ......................................... 16
Conversion to Propane (LP) Gas ............................. 17
Atmospheric & Direct Ignition Furnaces ................ 17
Measuring the Supply Gas Pressure.....................18
Measuring the Manifold Pressure..........................18
Oil Tank & Piping Installation ................................... 18
One-Line System .................................................. 18
Two-Line System...................................................18
Fuel line Hook-Up .................................................... 19
Fuel Line Bleeding ................................................... 19
Priming furnaces equipped with Honeywell...........19
R7184 primary control ........................................... 19
Priming furnaces equipped with Beckett 7505
primary control.......................................................19
Fuel Oil Type ........................................................... 20
STARTUP & ADJUSTMENTS ................................... 20
M1M Operating Instructions ..................................... 20
How to Shut Off Gas - Direct Ignition Models........21
M1B Operating Instructions ..................................... 21
How to Shut Off Gas Gun Models ......................... 21
M5S Operating Instructions ..................................... 21
How to Shut Off Oil Gun Models ........................... 22
Verifying Input Rate ................................................. 22
Verifying & Adjusting Temperature Rise .................. 22
Burner Adjustments ................................................. 22
Gas Pressure ........................................................ 22
Combustion Air ........................................................ 22
Gas Gun (M1B Models).........................................23
Oil Gun Only (M5S Models) .................................. 23
Electrode Setting (Oil Gun Only) ............................. 23
Switching Ignition Control between Interrupted
and Intermittent Duty ............................................... 23
OPERATING SEQUENCE ......................................... 23
Direct Ignition Furnaces (M1M Models) ................... 23
Gas Gun Furnaces (M1B Models) ........................... 23
Oil Gun Furnaces (M5S Models) ............................. 23
TROUBLESHOOTING ............................................... 24
Direct Ignition Furnaces (M1M Models) &
Gas Gun Furnaces (M1B Models) ........................... 24
Oil Gun - Honeywell R7184 or Beckett 7505
Controls Only - M5S Series ..................................... 25
FURNACE CONTROLS & FUNCTIONS ................... 26
MAINTENANCE ......................................................... 27
Installer Information ................................................. 27
Additional Oil Furnace Maintenance ........................ 27
OPTIONAL ACCESSORIES ...................................... 27
Optional Add-On Air Conditioning ............................ 27
FIGURES & TABLES ................................................. 28
Table 10. M1/M5 Furnace Specifications -
Factory Settings .................................................... 28
Table 11. A/C Blower Speed Selection Chart ....... 28
Gas Information ....................................................... 29
Table 12. Gas Flow Rates ..................................... 29
Table 13. Gas Pipe Capacities .............................. 29
Table 17. High Altitude Deration Chart for
Propane Gas ......................................... 30
Electrical Information ............................................... 31
Figure 35. Gas Direct Ignition Furnace, Heating &
A/C Ready - All M1M Models ............... 31
Figure 36. Gas and Oil Furnaces, A/C Ready -
M1B & M5S (066, 086) Models ............ 32
INSTALLATION CHECKLIST .................................... 36
3
IMPORTANT SAFETY INFORMATION
Safety markings are used frequently throughout this
manual to designate a degree or level of seriousness and
should not be ignored. WARNING indicates a potentially
hazardous situation that if not avoided, could result in
personal injury or death. CAUTION indicates a potentially
hazardous situation that if not avoided, may result in minor
or moderate injury or property damage.
WARNING:
The safety information listed below must be
followed during the installation, service, and
operation of this furnace. Failure to follow safety
recommendations could result in possible
damage to the equipment, serious personal
injury or death.
WARNING:
Do not install this furnace if any part has been
submerged under water. A flood damaged furnace
is extremely dangerous. Attempts to use the
furnace may result in fire or explosion. A qualified
service agency should be contacted to inspect the
furnace and to replace any electrical or control
system parts that have been wet or under water.
CAUTION:
Operating gas furnaces in construction
environments can cause a variety of problems
within the furnace and may significantly
reduce the life or the performance of the
furnace. Therefore operating the furnace during
construction is not permitted and will void the
warranty.
REQUIREMENTS & CODES
This furnace must be installed in accordance with
these instructions, all applicable local building codes
and the current revision of the National Fuel Gas Code
(NFPA54/ANSI Z223.1) or the Natural Gas and Propane
Installation Code, CAN/CSA B149.1.
Use only with type of gas approved for this furnace.
Refer to the furnace rating plate.
Install this furnace in accordance to the minimum
clearances to combustible materials listed in Table 1,
(page 5).
• Provide adequate combustion and ventilation air to the
furnace space as specified on page 6 and page 22.
Do not block or obstruct air openings on the furnace,
air openings to the area where the furnace is installed,
or the space around the furnace.
• Combustion products must be discharged outdoors.
Connect this furnace to an approved vent system, as
specified on page 10.
Never test for gas leaks with an open flame. Use
a commercially available soap solution to check all
connections. See page 15.
This furnace is designed to operate with a maximum
external pressure rise of 0.5 inches of water column.
NOTE 1: The static pressure measurement should not
include the coil (if applicable). Consult Table 10, (page
28) and the rating plate for the proper circulating air
flow and temperature rise.
NOTE 2: It is important that the duct system be designed
to handle the desired flow rate and external pressure
rise. An improperly designed duct system can result in
nuisance shutdowns, and comfort or noise issues.
When supply ducts carry air circulated by the furnace
to areas outside the space containing the furnace, the
return air shall also be handled through the front door
of the furnace. Make sure there is sufficient return air
through the door. See return air connections page 6.
Additional information listed below is for reference
purposes only and does not necessarily have jurisdiction
over local or state codes. Always consult with local
authorities before installing any gas appliance.
Combustion & Ventilation Air
US: National Fuel Gas Code (NFGC), Air for Combustion and
Ventilation
CANADA: Natural Gas and Propane Installation Codes
(NSCNGPIC), Venting Systems and Air Supply for Appliances
Duct Systems
US and CANADA: Air Conditioning Contractors Association
(ACCA) Manual D, Sheet Metal and Air Conditioning
Contractors National Association (SMACNA), or American
Society of Heating, Refrigeration, and Air Conditioning
Engineers (ASHRAE) Fundamentals Handbook
Electrical Connections
US: National Electrical Code (NEC) ANSI/NFPA 70
CANADA: Canadian Electrical Code CSA C22.1
Gas Piping & Gas Pipe Pressure Testing
US: NFGC and National Plumbing Codes
CANADA: NSCNGPIC
General Installation
US: Current edition of the NFGC and the NFPA 90B. For
copies, contact the National Fire Protection Association Inc.,
Batterymarch Park, Quincy, MA 02269; or American Gas
Association, 400 N. Capitol, N.W., Washington DC 20001 or
www.NFPA.org
CANADA: NSCNGPIC. For a copy, contact Standard Sales,
CSA International, 178 Rexdale Boulevard, Etobicoke
(Toronto), Ontario, M9W 1R3 Canada
Safety
US: (NFGC) NFPA 54–1999/ANSI Z223.1 and the Installation
Standards, Warm Air Heating and Air Conditioning Systems
ANSI/NFPA 90B.
Federal Manufactured Home Constructions & Safety Standard
(H.U.D. Title 24, Part 3280.707[a][2])
The Standard for Manufactured Home Installations
(Manufactured Home Sites, Communities, and Set-Ups) ANSI
A225.1 and/or CAN/CSA-2240 MH Series).
American National Standard (ANSI-119.2/NFPA-501C) for
all recreational vehicle installations.
CANADA: CAN/CSA-B149.1 and .2–M00 National Standard
of Canada. (NSCNGPIC)
4
The Commonwealth of Massachusetts requires
compliance with regulation 248 CMR 4.00 and 5.00 for
installation of through – the – wall vented gas appliances
as follows:
1. For direct-vent appliances, mechanical-vent heating
appliances or domestic hot water equipment, where the
bottom of the vent terminal and the air intake is installed
below four feet above grade the following requirements
must be satisfied:
a.) A carbon monoxide (CO) detector and alarm shall be
placed on each floor level where there are bedrooms.
The detector shall comply with NFPA 720 (2005
Edition) and be mounted in the living area outside
the bedroom(s).
b.) A (CO) detector shall be located in the room that
houses the appliance or equipment and shall:
Be powered by the same electrical circuit as the
appliance or equipment. Only one service switch shall
power the appliance and the (CO) detector;
Have battery back-up power;
Meet ANSI/UL 2034 Standards and comply with
NFPA 720 (2005 Edition); and Approved and listed
by a Nationally Recognized Testing Laboratory as
recognized under 527 CMR.
c.) A Product-approved vent terminal must be used, and
if applicable, a product-approved air intake must be
used. Installation shall be in strict compliance with the
manufacturer’s instructions. A copy of the installation
instructions shall remain with the appliance or
equipment at the completion of the installation.
d.) A metal or plastic identification plate shall be mounted
at the exterior of the building, 4 feet directly above
the location of vent terminal. The plate shall be of
sufficient size, easily read from a distance of eight
feet away, and read “Gas Vent Directly Below”.
2. For direct-vent appliances, mechanical vent heating
appliances or domestic hot water equipment where the
bottom of the vent terminal and the air intake is installed
above four feet above grade the following requirements
must be satisfied:
a.) A (CO) detector and alarm shall be placed on each
floor level where there are bedrooms. The detector
shall comply with NFPA 720 (2005 Edition) and be
mounted in the living area outside the bedroom(s).
b.) The (CO) detector shall:
Be located in the room that houses the appliance or
equipment;
Be hard-wired, battery powered or both.
Shall comply with NFPA 720 (2005 Edition).
c.) A product-approved vent terminal must be used, and
if applicable, a product-approved air intake must be
used. Installation shall be in strict compliance with the
manufacturer’s instructions. A copy of the installation
instructions shall remain with the appliance or
equipment at the completion of the installation.
GENERAL INFORMATION
CAUTION:
Do Not alter or modify this furnace or any of
its components.
Never attempt to repair damaged or inoperable
components. This may cause unsafe operation,
explosion, fire and/or asphyxiation.
If furnace malfunctions or does not operate
properly, contact a qualified service agency
or gas utility for assistance.
Minimum Clearances
This heating appliance must be installed with clearances
not less than the minimums listed in Table 1, (page 5).
This furnace must be installed with ample clearance for
easy access to the air filter, blower assembly, burner
assembly, controls, and vent connections. See Figure 1,
Figure 2, and Figure 3 (page 5).
The dimensions of the room or alcove must be able to
accommodate the overall size of the furnace and the
installation clearances listed in Table 1 and in Figure 4
(page 5).
Alcove installations: minimum 18” clearance at front
of furnace shall be provided for future servicing. A
removable access panel should be installed between
top of the furnace door frame and the ceiling.
Closet installations must use a louvered door having
a minimum free area of 235 in
2
when located 6” from
furnace or 390 in
2
for 5 ton ready M1/M5 furnaces. For
special clearance between 1” - 6”, requirements are a
louvered door with a minimum of 250 in
2
free area, with
the openings in the closet door in line with the louvered
openings in the furnace door. A fully louvered closet
door may be used. See Circulating Air Requirements
section (page 6).
The furnace must be kept free and clear of insulating
material. Examine the furnace area when the furnace is
installed or when insulation is added. Insulating material
may be combustible.
Applications
M1 Series gas and M5 Series oil furnaces are listed direct
vent (sealed combustion), downflow heating appliances for
manufactured (mobile) homes and recreational vehicles.
The furnace must be located so that venting can be
properly achieved.
Air conditioning may be added to structures with M1/M5
series furnaces using air conditioning or conventional
units. This Installation Instruction manual includes
special requirements for incorporation of air conditioning
equipment to the M1/M5 series of furnaces. See Table
11, (page 28).
Multi-speed blower assemblies shown in Table 2, (page
5), have been certified for field installation in M1/M5
Series furnaces.
5
“A”- 56"
19 3/4"
23 3/4"
“B”- 76"
“A” Model without Coil Cabinet
“B” Model with Coil Cabinet
Figure 4. Overall Dimensions
Table 1. Minimum Clearances
ALL MODELS CLOSET ALCOVE
Front 6” 18”
Back 0” 0”
Sides 0” 0”
Roof Jack 0” 0”
Top 6” 6”
Top and Sides of Duct 0” 0”
Bottom of Duct
A Cabinet (w/ coil box) 0” 0”
A Cabinet (w/o coil box) 1/4” 1/4”
B Cabinet 0” 0”
Table 2. Blower Assemblies
PART
NO.
BLOWER / MOTOR ASSEMBLY
A/C CAPACITY
(TONS)
BLOWER
WHEEL
MOTOR
(HP)
903413 11 x 8 1/2 2, 2½, 3 & 4
903890 11 x 8 3/4 2, 2½, 3, 4 & 5
Removable access
panel should be
installed above
furnace door frame
to access roof jack
Nearest
Wall or
Partition
18"
(457 mm)
6" (152 mm)
Top Clearance
0" Side
Clearance
to Furnace
Cabinet
6" (152 mm)
Top Clearance
0" Side
Clearance
to Furnace
Cabinet
Provide min. 235
sq. in. (1516 cm )
open free area in
front or side wall
2
or
In closet
door
located
at top,
center
or bottom
CLOSET DOOR
6" (152 mm)
Top Clearance
Provide min. 250
sq. in. (1613 cm )
open free area in
front or side wall
2
a fully
louvered
door may
be used
CLOSET DOOR
6"
(152 mm)
1"
(25 mm)
0" Side
Clearance
to Furnace
Cabinet
or
in closet
door
Figure 2. Closet Installation
Figure 3. Special 1” Clearance
Figure 1. Alcove Installation
6
Unit Location
The furnace shall be appropriately located to the supply
and return air distribution system (page 6). Sides and
back of the furnace may be enclosed by wall framing.
See Minimum Clearances section on page 4.
The furnace installation is only intended for free air return
through the furnace door louvers. DO NOT connect a
ducted return air system directly to the furnace. Improper
installation may create a hazard and damage equipment,
as well as void all warranties.
Furnace may be installed on combustible flooring when
using manufacturer approved duct connectors. See
page 6.
When installed in a residential garage, the furnace must
be positioned so the burners and the source of the
ignition are located no less than 18 inches above the
floor and protected from physical damage by vehicles.
CIRCULATING AIR REQUIREMENTS
WARNING:
Do not allow combustion products to enter the
circulating air supply. Failure to prevent the
circulation of combustion products into the
living space can create potentially hazardous
conditions including carbon monoxide poisoning
that could result in personal injury or death.
The surface that the furnace is mounted on must
provide sound physical support of the furnace
with no gaps, cracks or sagging between the
furnace and the floor or platform.
Circulating air ductwork must not be connected
to any other heat producing device such as a
fireplace insert, stove, etc. This may result in fire,
explosion, carbon monoxide poisoning, personal
injury, or property damage.
Return Air
U.S.A. home manufacturers shall comply with all of the
following conditions to have acceptable return air systems
for closet installed forced air heating appliances:
The return air opening into the closet shall not be less
than specified in the appliance’s listing.
The cross-sectional area of the return duct system
leading into the closet, when located in the floor or
ceiling shall not be less than 235 in
2
(or 390 in
2
for M1/
M5 Furnaces with 5 ton blower kits).
CAUTION:
HAZARD OF ASPHYXIATION: Do not cover or
restrict return air opening.
Means shall be provided that prevent inadvertent closure
of flat objects placed over the return air opening located
in the floor of the closet (versus the vertical front or side
wall).
The total free area of openings in the floor or ceiling
registers serving the return air duct system must be at
least 235 in
2
. At least one register should be located
where it is not likely to be covered by carpeting, boxes
and other objects.
Materials located in the return duct system must have a
flame spread classification of 200 or less. This includes
a closet door if the furnace is in a closet.
Noncombustible pans having 1” upturned flanges are
located beneath openings in a floor duct system.
Wiring materials located in the return duct system shall
conform to Articles 300-22 of the National Electrical
Code (ANSI C1/NFPA-70).
Gas piping is not run in or through the return duct system.
CAUTION:
HAZARD OF ASPHYXIATION: Negative pressure
inside the closet, with closet door closed and
the furnace blower operating on high speed,
shall be no more negative than minus 0.05 inch
water column.
Test the negative pressure in the closet with the air-
circulating fan operating at high speed and the closet
closed. The negative pressure is to be no more negative
than minus 0.05 inch water column.
Air conditioning systems may require more duct register
and open louver area to obtain necessary airflow.
Supply Air
For proper air distribution, the supply duct system must be
designed so that the static pressure measured external
to the furnace does not exceed the listed static pressure
rating shown on the furnace rating plate.
Location, size, and number of registers should be selected
on the basis of best air distribution and floor plan of
the home. The supply air must be delivered to the
conditioned space by duct(s) secured to the furnace
casing, running full size and without interruption.
Three typical distribution systems are shown in Figure 5
Figure 5. Typical Supply Duct System
A Single trunk duct
B
Dual trunk duct
w/crossover connector
C
Transition duct
w/branches
7
FURNACE INSTALLATION
NOTE: These Installation procedures are suggested for
typical furnace installations. Since each installation is
different, the sequence of instructions may differ from
the actual installation. Only qualified HVAC technicians
should install this furnace.
The installer must be familiar with and comply with all
codes and regulations applicable to the installation of
these heating appliances and related equipment. In
the absence of local codes, the installation must be in
accordance with the current provisions of one or more of
the following standards.
Federal Manufactured Home Constructions & Safety
Standard (H.U.D. Title 24, Part 3280.707[a][2])
American National Standard (ANSI-119.2/NFPA-501C)
for all recreational vehicle installations.
American National Standard (ANSI-Z223.1/NFPA-54)
and/or CAN/CSA B149 for all gas-fired furnace models.
American National Standard (ANSI-Z95.1/NFPA-31)
and/or CSA B139 for all oil-fired furnace models.
American National Standard (ANSI-C1/NFPA-70) and/or
CSA 22.1 Canadian Electric Code Part 1 for all electrical
field wiring.
Units have been certified under standards UL 307A & B,
UL727-1999, ANSI Z21.47/CSA 2.3, and CSA B140.10.
General Information
The furnace must be leveled at installation and attached
to a properly installed duct system. Do not use the
back of the furnace for return air. See page 6
for circulating requirements.
The furnace must be installed so that all electrical
components are protected from water
The dimensions of the room or alcove must be able to
accommodate the overall size of the furnace and the
installation clearances listed in Table 1, (page 5)
and Figure 1 (page 5)
The furnace must be installed upstream from a
refrigeration system.
M1 series (gas) and M5 series (oil) furnaces are
certified for use on wood flooring or supports, but must
be installed on top of a duct connector. This factory
supplied accessory must be installed in the floor cavity
and attached to the supply air duct before the furnace
is installed.
Locating & Cutting Duct Openings
Floor cut-outs and fuel line holes must be carefully located
to avoid misalignment of the furnace, and vent piping.
To locate standard ducts see Figure 6. For round ducts,
see Figure 7.
1. Measure 10” from the rear wall or alcove and mark the
centerline of the cut-out on the floor.
2. Using the centerline as a starting point, draw the rest
of the duct cut-out to the dimensions shown in Figure
6 or Figure 7.
3. Cut out the floor opening 1/16” larger than the actual
cutout drawn. This will allow some clearance when
installing the duct connector.
4. Measure from the top of the floor down to the top of the
supply air duct to obtain the depth of the floor cavity.
FLOOR CUT-OUT
FOR STANDARD
DUCT CONNECTORS
C
L
C
L
C
L
24"
23 1/4"
21 3/4"
14 1/2"
2 1/4"
2 3/4"
20"
CUT-OUT FOR
OPTIONAL
COOLING COIL
REAR WALL OF CLOSET OR ALCOVE
1 3/4"
2"
3/4"
C
L
C
L
C
L
10"
C
L
FURNACE OUTLINE
14 1/2"
ALT FUEL-LINE
ENTRY 1 1/4" Dia.
FURNACE
OUTER
DOOR
FUEL
LINE
1 3/4"
3/4"
1 7/8"
2 7/8"
Figure 6. Cut-Out Dimensions for
Standard Duct Connectors
FLOOR
CUT-OUT FOR
ROUND DUCT
(14 1/4” DIAMETER)
C
L
C
L
C
L
C
L
24"
23 1/4"
21 3/4"
20"
CUT-OUT FOR
OPTIONAL
COOLING COIL
ALT FUEL-LINE
ENTRY 1 1/4" Dia.
FURNACE
OUTER
DOOR
REAR WALL OF CLOSET OR ALCOVE
FUEL
LINE
1 3/4"
2"
3/4"
C
L
C
L
10"
FURNACE OUTLINE
1 3/4"
10"
3/4"
1 7/8"
2 7/8"
C
L
Figure 7. Cut-Out Dimensions for
Round Duct Connectors
Bend tabs
up 90°
Mounting Plate
Duct
Connector
Connector
Tabs
Supply
Air Duct
Hole for
Gas Line
Wood Floor
Figure 8. Standard Duct Connector Installed
8
IF FLOOR
CAVITY
“X” IS:
DUCT CONNECTOR
TYPE & PART NUMBER
STANDARD DUCT ROUND DUCT
7/8” / (22) 901987A 904008
2” / (51) 901988A N/A
4-1/4” / (108) 901989A 904010
6-1/4” / (159) 901990A 904011
8-1/4” / (210) 901991A 904012
10-1/4” / (260) 901992A 904013
12-1/4” / (311) 901993A 904014
NOTE: Dimensions shown as Inches / (Millimeter)
Table 3. Duct Connector Sizes
DUCT CONNECTOR
SUPPLY
AIR DUCT
BEND TABS TIGHTLY
AGAINST SUPPLY AIR DUCT
Figure 10. Duct Connector Tabs
OPTION 1 OPTION 2
Supply
Air Duct
Fold Flap Here
Fold Flap Here
Remove
this
Flap
Remove
this
Flap
Cut Here
Cut Here
Cut Here
Cut Here
Cut Here
Cut Here
Cut Here
Cut Here
Cut Here
Fold Flap Here
Fold Flap Here
Figure 11. Narrow Air Duct Openings
DUCT
CONNECTOR
SCREWS
MOUNTING
PLATE
FUEL LINE
HOLE
FUEL LINE
HOLE
14” SUPPLY
CONNECTION
Figure 13. Round Duct Connector Installed
MTG. PLATE TABS
SLIDE FURNACE
ALL THE WAY BACK
ONTO MTG. PLATE
SUPPLY AIR DUCT
Knockout Over Holes
SECURE FURNACE
WITH 2 FASTENERS AT FRONT
CORNER HOLES
Figure 14. “A” & “B” Cabinet Furnaces
Figure 12. Narrow Ducts
Narrow
Duct
Narrow
Duct
Duct connector tabs
Staples or sheet metal screws
Duct
Flap
Narrow
Duct
Duct
Connector
Sheet metal
screws
Figure 9. Floor Cavity
“X”
FLOOR OPENING
R
SUPPLY AIR DUCT
FUEL LINE HOLES
MTG. PLATE TABS
SLIDE FURNACE
BACK AGAINST
MTG. PLATE
SECURE FURNACE
WITH 2 FASTENERS
AT FRONT CORNER HOLES
SUPPLY
AIR DUCT
Figure 15. “A” Cabinet Furnace on Coil Cabinet
9
NOTE: The depth of the floor cavity shown as “X” in
Figure 9 (page 8) will determine the correct duct
connector.
5. Determine which duct connector to use from Table 3,
(page 8).
6. Measure and drill gas hole and cut out for cooling coil
(if applicable). See Figure 6 or Figure 7.
Standard Duct Connector Installation
The standard duct connector is designed for use on
ducts 12” in width. Ducts narrower than 12” may not
allow sufficient clearances for this type of installation. See
Alternate Attachment Method section below.
1. Center the duct connector in the floor opening with
bottom tabs resting on top of the supply air duct.
2. Mark the cut-out area on the supply air duct by tracing
around the connector tabs of the duct connector. See
Figure 8 (page 7).
3. Remove the duct connector and cut out the marked
area of the supply air duct 1/4” larger the actual cutout
drawn.
4. Install the duct connector back in the floor opening with
the bottom tabs extending into the supply air duct.
5. Install the mounting plate under the back side of the
duct connector as shown in Figure 8. Align the screw
holes in both components.
6. Secure the duct connector and the mounting plate to
the wood floor with appropriate size screws.
7. Bend the connector tabs on the bottom of the duct
connector upwards and as tight as possible against
the supply air duct.
8. Bend both tabs up 90° on the mounting plate. See
Figure 10 (page 8).
9. Seal all connections with industrial grade sealing tape
or liquid sealant.
NOTE: Requirements for sealing ductwork vary
from region to region. Consult with local codes for
requirements specific to your area.
Alternate Attachment Method
The standard duct connector is designed for use on ducts
12” in width. However if there is insufficient clearance to
bend the duct connector tabs, this alternate attachment
method may be used.
1. Score and cut the top of the supply air duct as indicated
in Option 1 or Option 2. See Figure 11 (page 8).
NOTE: If Option 1 is selected, cut out the metal from
the shaded area.
2. Fold the two flaps (Options 1 or 2) up to form the opening
for the duct connector.
3. Install the duct connector with the bottom tabs extending
into the supply air duct.
4. Bend the tabs on the bottom of the duct connector
upwards and as tight as possible against the supply
air duct. See Figure 12 (page 8).
5. Form the flaps (Options 1 or 2) up against the duct
connector as tight as possible.
6. Secure the duct connector flaps to the supply air duct
with staples (3 minimum) or if a 2x block/joist is not
provided, use sheet metal screws (2 minimum).
NOTE: The duct connector tabs may be attached to
the air duct with sheet metal screws or other suitable
fasteners as long as the duct connector and the air duct
are securely attached.
7. Seal all connections with industrial grade sealing tape
or liquid sealant.
NOTE: Requirements for sealing ductwork vary
from region to region. Consult with local codes for
requirements specific to your area.
Round Duct Connector Installation
1. Apply a bead of caulking, mastic, or other approved
sealant around bottom side of connector.
2. Install and center the duct connector in the floor opening.
3. Install the mounting plate under the back side of the
duct connector. See Figure 13. NOTE: Align the screw
holes in both components.
4. Secure the duct connector and the mounting plate to
the wood floor with appropriate size screws.
5. Connect the round supply duct to the underside of the
duct connector and secure them with field supplied
sheet metal screws.
6. Seal all connections with industrial grade sealing tape
or liquid sealant.
NOTE: Requirements for sealing ductwork vary
from region to region. Consult with local codes for
requirements specific to your area.
Installing the Furnace
Sides and back of the furnace may be enclosed by wall
framing such as in a closet or alcove. The dimensions
of the room or alcove must be able to accommodate the
overall size of the furnace shown in Figure 4 (page 5)
and the installation clearances outlined on page 4. The
furnace shall be appropriately connected to the supply
distribution system as shown in Figure 14 (page 8) &
Figure 15 (page 8).
1. Remove furnace outer door(s) and bottom fuel line
knockout.
2. Place furnace onto duct connector and center with floor
opening.
3. Slide onto mounting plate. (Bottom rear slots on furnace
should engage with mounting plate tabs.)
4. Secure front with one (1) fastener at each corner. See
Figure 14 & Figure 15.
NOTE: Additional fasteners may be used at rear, sides
or through door frame, as desired, to secure furnace to
closet or alcove framing.
10
Figure 16. Ceiling Cavity Depth
ROOF JACK
CROWN
SLANT DECK
FLASHING
PITCHED
ROOF
CEILING
CEILING
CAVITY
Roof
Opening
"X" (SEE TABLE 5)
Flue Pipe
Combustion Air Pipe
56"
or
76"
Furnace
“A”
“B”
SLANT DECK
FLASHING
PITCHED
ROOF
CEILING
ROOF
OPENING
"X" (SEE TABLE 5)
CEILING
CAVITY
CEILING
OPENING
ROOF JACK
CROWN
Figure 17. Example of Flat Jack with Flashing
5/12 ROOF SLOPE
2
SLANT DECK
/12
1
2
ROOF JACK WITH
2
FLASHING
/12 SLANT
1
2
Figure 18. Example of 2½ / 12 Slant Jack
with Flashing
ROOF JACK INSTALLATION
Required ceiling and roof cut-out openings must be
carefully located to avoid misalignment of the furnace
and Roof Jack. NOTE: Install only roof jack assemblies
listed in Table 4, (page 11) on this heating appliance.
Roof Jack Selection
1. Determine depth of ceiling cavity from center of roof
opening to center of ceiling opening noted as “Dimension
A” in Figure 16 (page 10).
2. Determine ceiling height and subtract height of furnace
noted as “Dimension B” in Figure 16 (page 10).
3. Add dimensions “A” & “B” (and X from Table 5, (page
11) if slant deck flashing is used). The total length of
[A] + [B] + [X] must be within the minimum and maximum
range of the roof jack listed in Table 4.
Application Notes
FAW, FAWT, SAW and SAWT Series Roof Jacks with a
5” diameter inner vent pipe may be used with all models
of M1 Series gas and M5 Series oil furnaces.
F = Flat Flashing: flexes from 0/12 to 1/12 roof slope.
See Figure 17 (page 10).
S = Slant Flashing: 2.5/12 Slope flexes from 1/12 to
4/12 roof slope, 4/12 flexes from 3/12 to 5/12.
See Figure 18 (page 10).
Stainless steel roof jacks are available.
M1/M5 furnaces may be used with roof jack systems
and extension accessories as tall as 170” (except M1M
056 & M1B 066 models, which are limited to 120”).
An internal roof jack extension (p/n 901935 - 10”, p/n
903107 - 18”) can be used to increase roof jack height.
All connections inside the home must be made below
the ceiling.
This furnace must never be connected to a chimney
flue servicing a fireplace or other appliance designed
to burn solid fuel.
If the roof jack crown is covered or blocked with snow, the
furnace will not operate properly. If the home is located
in regions where snow accumulation exceeds 7” (HUD
snowload zones) use an external roof jack extension
(p/n 901937). A maximum of 2 extensions per roof jacks
can be used. Extensions are optional accessories and
may be purchased through your distributor.
Locating & Cutting Roof / Ceiling Openings
IMPORTANT NOTE:
Do not allow debris to fall into the furnace. This
could cause unsafe operation and void the furnace
warranty. Use the top cap that comes with the furnace
packaging (or alternate protector) to prevent debris
from falling into the furnace before the final roof jack
connection is made.
NOTE: Refer to the installation instructions provided
with optional air conditioning packages when installing
furnaces with optional cooling coil cabinet or with optional
C* series indoor coils.
1. Locate center of Roof Jack opening, measure 13 1/2”
from the rear wall of closet or alcove along the center
line of furnace and floor opening. See Figure 19.
11
2. Cut ceiling and roof holes:
Ceiling = 8 3/4” (222 mm) diameter
Roof = 9 3/8” (238 mm) diameter
Installing The Roof Jack
1. Apply caulking compound on underside of roof flashing
to form a continuous strip at least 3/8” wide around the
underside of the perimeter of the flashing. For flat roof,
see Figure 20 or see Figure 21 (page 12) if roof is
pitched.
2. Connect roof jack assembly to the furnace. Insert
telescoping roof jack assembly through the opening
cut on the roof.
3. Connect inner flue pipe to vent collar of the furnace.
See Figure 22 (page 12).
4. Connect combustion air pipe to furnace collar with sheet
metal screw. See Figure 22.
NOTES:
It is recommended that the connection of the combustion
air pipe to the furnace be made before the flashing is
secured to the roof to maintain alignment of roof jack
and furnace connections.
For replacement furnaces, be sure the inner flue pipe
connects over the furnace vent collar. DO NOT use a
smaller diameter inner flue pipe which could slide
inside the furnace vent collar and restrict the flow
of furnace flue products.
5. Attach roof flashing. If necessary, shift roof flashing
slightly in the roof opening so that assembly is in
alignment with furnace.
NOTE: If flashing is mounted on 12 degree angle, it
may be necessary to adjust the angle to match the roof
pitch; (1/12 - 4/12 maximum).
6. Press down firmly on roof flashing (over caulking) to
make the seal with roof water tight.
7. Secure flashing with appropriate fasteners. NOTE: For
added protection against leaks, coat the flashing plate
and fasteners with approved roofing compound.
NOTE: Upper roof jack crown to be stored in a
prominent location inside manufactured home until
on-site installation.
Installing Transit-Mode Venting System
(Before Home is Moved to Site)
NOTE: For transit purposes, the transit kit (P/N 903838)
should be installed before home is moved to site.
1. Furnace must be installed in accordance to furnace
installation manual.
2. Select appropriate roof jack from Table 4, (page 11)
3. Roof jack (less upper roof jack crown), with weather
cap to be installed as described in Installing The Roof
Jack section.
4. Install the four warning tags (factory supplied) on these
items:
Weather cap
Fuel line connection point (Gas) or furnace burner (Oil)
Furnace flame observation door (Gas or Oil)
Furnace wall thermostat
Table 4. Roof Jack Assemblies
SSAW
27
47 - 2
AW= ALL WEATHER
FLASHING
PITCH/12" RISE
0=FLAT
2=2.5/12
4=4/12
MIN. ADJ.
LENGTH
F = FLAT FLASHING
S = SLANT FLASHING
MAX. ADJ.
LENGTH
FLUE STEEL TYPE
A= ALUMINIZED
S=STAINLESS
MODEL NUMBER
APPROX. LENGTH
BELOW FLASHING
(F,S)AW1523-(0,2,4)(A,S) 15” - 23”
(F,S)AW2135-(0,2,4)(A,S) 21” - 35”
(F,S)AW2747-(0,2,4)(A,S) 27” - 47”
(F,S)AW3563-(0,2,4)(A,S) 35” - 63”
(F,S)AW5195-(0,2,4)(A,S) 51” - 95”
NOTE: Not all models are available. Check with your local distributor
for available models.
Figure 19. Cut-Out Dimensions for
Flue & Roof Jack
CEILING
CUT-OUT FOR
FLUE AND
ROOF JACK
C
L
C
L
24"
20"
13 1/2"
REAR WALL OF CLOSET OR ALCOVE
10"
FURNACE
OUTER
DOOR
FURNACE OUTLINE
Table 5. Slant Deck Flashings
ROOF JACK
SERIES
IF ROOF
PITCH IS:
SLANT DECK
FLASHING
NUMBER
“X”
“F Series
2” in 12” 903893 (2.5/12) 2-1/8”
2-1/2” in 12” 903893 (2.5/12) 2-1/2”
3” in 12” 903894 (3/12) 2-7/8”
3-1/2” in 12” 903894 (3/12) 3-1/4”
4” in 12” 903895 (4/12) 3-5/8”
“S” Series
(2.5 / 12 Pitch only)
4-1/2” in 12” 903895 (2.5/12) 2-1/8”
5” in 12” 903895 (2.5/12) 2-1/2”
5-1/2” in 12” 903894 (3/12) 2-7/8”
6” in 12” 903894 (3/12) 3-1/4”
6-1/2” in 12” 903895 (4/12) 3-5/8”
Optional deck flashings for flat and 2.5/12 pitch roof jacks.
4/12 pitch roof jacks not applicable.
12
Removing the Transit-Mode Venting System
(After home is moved to site)
WARNING:
Failure to properly secure the flue pipe to
the furnace may result in fire, explosion or
asphyxiation when operating the furnace.
1. Transit-mode weather cap to be removed and upper
roof jack crown installed. Do not discard the screws.
See Figure 23.
2. Place upper roof jack (crown) on the flue pipe assembly.
NOTE: Make sure inside flue pipe attaches over inner
flue pipe and outer Roof Jack pipe fits over outer pipe.
3. Secure in place using three sheet metal screws (#10
x 1/2”) removed in step 1. Do not use the same holes
which secured the rain cap in place.
4. Remove and discard all 4 venting system warning tags.
Figure 20. Flat Roof
Secure roof jack with
appropriate fasteners
after connecting to
furnace
Caulk under roof
flashing to prevent
water leakage
Roof
Ceiling
Optional 2-piece ceiling
ring #902521
Upper Roof Jack Section
Secure lower roof
jack section with
no. 10 S.M. screws
Caulk under roof
ashing to prevent
water leakage
Optional Slant
Deck Flashing
Secure ashing
with appropriate
fasteners
Ceiling
Figure 21. Pitched Roof
CONNECT OUTER
FLUE SHIELD
INNER FLUE PIPE
VENT COLLAR
MOUNTING
FLANGE
Figure 22. Combustion Air Pipe Connection
SCREWS
COMPLETED
ASSEMBLY
TO FURNACE
UPPER ROOF
JACK (CROWN)
INNER FLUE PIPE
FLUE ASSEMBLY
OUTER PIPE
FLASHING
WEATHER CAP
Figure 23. Roof Jack Crown
Figure 24. Control Panel (All Models)
On-Off
Switch
Blower
Plug
Power
Entry
On-Auto Switch
(Heating Models Only)
Thermostat Wires
Furnace
Control Box
To combustion
Blower or Flame
Roll-out Switch
To Gas Valve
or Burner
13
ELECTRICAL INFORMATION
WARNING:
ELECTRICAL SHOCK, FIRE OR
EXPLOSION HAZARD
Failure to follow safety warnings exactly could
result in serious injury or property damage.
Improper servicing could result in dangerous
operation, serious injury, death or property
damage.
Before servicing, disconnect all electrical
power to furnace.
When servicing controls, label all wires prior
to disconnecting. Reconnect wires correctly.
Verify proper operation after servicing.
Line Voltage Wiring
WARNING:
To avoid electric shock, personal injury, or death,
turn off the electric power at the disconnect or the
main service panel before making any electrical
connections.
Electrical connections must be in compliance with all
applicable local codes with the current revision of the
National Electric Code (ANSI/NFPA 70).
For Canadian installations the electrical connections
and grounding shall comply with the current Canadian
Electrical Code (CSA C22.1 and/or local codes).
It is recommended that 115VAC line voltage be supplied
to the furnace from a dedicated branch circuit containing
the correct fuse or circuit breaker for the furnace as listed
in Table 6, (page 14).
IMPORTANT NOTE:
Refer to the wiring diagram inside the control box
cover or Figure 35 (page 31) & Figure 36 (page 32)
for the wiring of your particular unit. Any other wiring
methods must be acceptable to authority having
jurisdiction.
CAUTION:
Label all wires prior to disconnection when
servicing controls. Wiring errors can cause
improper and dangerous operation. Verify proper
operation after servicing.
IMPORTANT NOTE:
Proper line voltage polarity must be maintained in
order for the control system to operate correctly.
Verify the incoming neutral line is connected to the
white wire and the incoming “hot” line is connected
to the black wire. The furnace will not operate unless
the polarity and ground are properly connected as
shown in Figure 25 (page 14).
For installation of A-size Cabinet furnaces, allow sufficient
slack in the wiring if an optional cooling coil cabinet is
added at a later time. Use of copper conductors is
recommended.
Connecting Power Supply Wires
1. Remove the furnace control panel cover.
2. Route wires (115 VAC) through the strain relief on the
left side of the furnace control box. See Figure 24 (page
12).
3. Connect the hot wire to the black pigtail lead, and
the neutral wire to the white pigtail lead. Secure all
connections with suitable wire nuts.
4. Connect the ground wire to the grounding screw.
5. Reinstall the control panel cover and secure with the
original mounting screws.
Low Voltage Wiring
The furnace is designed to be controlled by a 24 VAC
thermostat. The thermostat’s wiring must comply with
the current provisions of the NEC (ANSI/NFPA 70) and
with applicable local codes having jurisdiction.
The thermostat must be installed according to the
instructions supplied by the thermostat manufacturer.
Low voltage connections (24 VAC) from the thermostat
are wired to the terminal strip on the integrated control
in the furnace.
• The thermostat should be mounted about 5 feet above
the floor on an inside wall. DO NOT install the thermostat
on an outside wall or any other location where its
operation may be adversely affected by radiant heat from
fireplaces, sunlight, or lighting fixtures, and convective
heat from warm air registers or electrical appliances.
Refer to the thermostat manufacturer’s instruction sheet
for detailed mounting information.
The nominal anticipator setting is 0.4. Refer to the
thermostat literature for additional information.
Five-conductor thermostat wire is recommended for 24
volt low-voltage circuit (2-wire is required for furnace
only; 5-wire for heating and optional cooling systems).
Refer to Table 6 for thermostat wire information.
Connecting Thermostat Wires
1. Insert 24 volt wires through the plastic grommet just
above the control panel.
2. Connect the thermostat wires to the furnace low voltage
pigtails (dependent on the installation application). See
Figure 25 (page 14)..
For M1 models: RH from the furnace is not connected;
RC of the furnace connects to the thermostat.
For M5 models: To connect an M5 to a thermostat
without an RH & RC connection, please refer to the
wiring diagram and the installation instructions
supplied in the kit [P/N 1018453]. Units installed with kit
[P/N 1018453] will not use the RH connection from the
furnace, RC on the furnace connects to the thermostat.
3. Connect low-voltage circuit to the wall thermostat.
14
4. A hole may be made in the furnace cabinet to ease
thermostat wiring. Make sure that the wiring is protected
from the sharp edge of the added hole.
Verifying Anticipator Setting
After the furnace is installed, check the thermostat
anticipator against the nominal setting of 0.4.
1. Connect the milliamp meter in series with one of the
gas valve’s low voltage terminals.
2. Energize the gas valve.
3. Read the value of the milliamps.
4. Adjust the heat anticipator of the thermostat to the
value on the milliamp meter. If the heat anticipator is
set too high, the furnace may delay turning on. If set too
low, the furnace may cycle frequently and not provide
comfort to the homeowner.
Grounding
WARNING:
To minimize personal injury, the furnace cabinet
must have an uninterrupted or unbroken electrical
ground. The controls used in this furnace require
an earth ground to operate properly. Acceptable
methods include electrical wire or conduit
approved for ground service. Do not use gas
piping as an electrical ground!
Figure 25. Thermostat Wiring
Table 6. Voltage Specifications & Thermostat Wire Gauge
FURNACE
MODEL
NUMBER-
FURNACE
INPUT
(BTUH)
CABINET
WIDTH
(IN.)
NOMINAL
ELECTRICAL
SUPPLY
MINIMUM
OPERATING
VOLTAGE
MAXIMUM
OPERATING
VOLTAGE
MAXIMUM
FURNACE
AMPERES
MAXIMUM
FUSE OR CIRCUIT
BREAKER AMPS*
MINIMUM
CIRCUIT
AMPACITY
1
MAXIMUM
OVERCURRENT
PROTECTION
2
M1MB 056 56,000 19 3/4 115-1-60 103 127 7.0 15 8.5 14.5
M1MB 070 70,000 19 3/4 115-1-60 103 127 7.0 15 8.5 14.5
M1MB 077 77,000 19 3/4 115-1-60 103 127 7.0 15 8.5 14.5
M1MB 090 90,000 19 3/4 115-1-60 103 127 7.0 15 8.5 14.5
M1BB 066 66,000 19 3/4 115-1-60 103 127 6.8 15 8.3 14.3
M1BB 086 86,000 19 3/4 115-1-60 103 127 6.8 15 8.3 14.3
M1MC 056 56,000 19 3/4 115-1-60 103 127 8.9 15 10.9 18.8
M1MC 070 70,000 19 3/4 115-1-60 103 127 8.9 15 10.9 18.8
M1MC 077 77,000 19 3/4 115-1-60 103 127 8.9 15 10.9 18.8
M1MC 090 90,000 19 3/4 115-1-60 103 127 8.9 15 10.9 18.8
M1BC 066 66,000 19 3/4 115-1-60 103 127 8.7 15 10.7 18.6
M1BC 086 86,000 19 3/4 115-1-60 103 127 8.7 15 10.7 18.6
NOTE: Minimum wire gauge and maximum fuse/circuit breaker amperage are based on MCA
1
and MOP
2
calculations. This furnace is approved
for installation with a 15 or 20 amp fuse/circuit breaker however wiring sizing must adhere to current version of the NEC and/or applicable local
codes depending upon the overcurrent protection.
* Time-delay fuses or circuit breakers are required.
THERMOSTAT WIRE GAUGE
RECOMMENDED THERMOSTAT WIRE LENGTH (TOTAL LENGTH)
2 - WIRE - HEATING 4 OR 5 WIRE - COOLING
24 55 ft. 25 ft.
22 90 ft. 45 ft.
20 140 ft. 70 ft.
18 225 ft. 110 ft.
Total wire length includes wire from furnace to the thermostat, from thermostat to outdoor unit, & from outdoor unit back to the furnace.
Rc
R
H
W
G
Y
Red
White
Green
Yellow
Red
White
Green
Grey
Thermostat
M1 Furnace
To AC Contactor
Rc
R
H
W
G
Y
Red
White
Green
Yellow
Red
White
Green
Grey
Thermostat
M5 Furnace
To AC Contactor
Red Red
TR
TW
Oil Burner
15
FUEL SUPPLY & PIPING
WARNING:
FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly could
result in serious injury or property damage.
Installation and service must be performed
by a qualified installer, service agency or the
gas supplier.
Do not store or use gasoline or other
flammable vapors and liquids in the vicinity
of this or any other appliance.
WHAT TO DO IF YOU SMELL GAS
Do not try to light any appliance.
Do not touch any electrical switch; do not
use any phone in your building.
Leave the building immediately.
Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s
instructions.
If you cannot reach your gas supplier, call
the fire department.
WARNING:
All piping must conform with local building codes,
or in the absence of local codes, with the most
recent edition of the National Fuel Gas Code ANSI
Z223.1 or (CAN/CSA B149.1). Failure to follow all
safety warnings could result in serious injury,
death or property damage.
This furnace may be installed with left, right, or bottom gas
entry. When connecting the gas supply, provide clearance
between the gas supply line and the entry hole in the
furnace casing to avoid unwanted noise and/or damage
to the furnace. Typical gas service hookup for this furnace
is shown in Figure 26 (page 16).
Table 13, (page 29) lists gas flow capacities for standard
pipe sizes as a function of length in typical applications
based on nominal pressure drop in the line.
IMPORTANT NOTES:
Some local regulations require the installation of a
manual main shut-off valve and ground joint union
external to the furnace. See Figure 26 (page 16).
The shut-off valve should be readily accessible for
service and/or emergency use. Consult the local
utility or gas supplier for additional requirements
regarding placement of the manual main gas shut-
off.
Gas piping must never run in or through air ducts,
chimneys, gas vents, or elevator shafts.
Compounds used on threaded joints of gas piping
must be resistant to the actions of -liquefied
petroleum gases.
The main gas valve and main power disconnect to
the furnace must be properly labeled by the installer
in case emergency shutdown is required.
• Flexible gas connectors are not recommended for
this furnace but may be used if allowed by local
jurisdiction. Only new flexible connectors may be
used. DO NOT reuse old flexible gas connectors.
A drip leg is recommended for a vertical run to the
unit.
All piping shall be black iron pipe. Internally tinned
copper tubing may be used for gas supply systems.
Fuel line installations other than typical installations
shown in Figure 26 (page 16) & Figure 27 (page
17) must comply with the fuel piping provisions
stated in the Federal Manufactured Home Standard
(H.U.D. TITLE 24, PART 3280) and the National Fuel
Gas Code (ANSI-Z223.1/NFPA-54).
Shut-off valve must be designed and listed for use
with liquid petroleum (L.P. gas).
A 1/8” NPT plugged tappings for test gauge
connection are present on the gas valve. See Figure
28 (page 17) for locations.
NOTE: Optional fuel inlet lines are available for all gas
furnace models to permit the addition of a 1/2” F.P.T.
shut-off valve above the floor.
The gas supply to your home will either be Natural Gas
or L.P. Your furnace is factory equipped to operate on
Natural Gas. If your gas supply is L.P., you must contact
a qualified serviceman or gas supplier to convert the
furnace. Instructions for conversion to propane are shown
on page 17. Factory installed orifice sizes are listed in
Table 10, (page 28).
For natural gas operation, the maximum inlet pressure
for the valve is 7” W.C and the minimum inlet pressure
is 4.5” W.C. Pressure is reduced to 3 1/2” W.C. by the
pressure regulator in the gas valve.
For LP gas, pressure to the gas valve must be more than
11” W.C. but not more than 13” W.C. Pressure is reduced
to 10” W.C. by the pressure regulator in the gas valve.
Leak Check
WARNING:
FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly could
result in serious injury or property damage.
Never test for gas leaks with an open flame. Use
a commercially available soap solution made
specifically for the detection of leaks to check
all connections. A fire or explosion may result
causing property damage, personal injury or
loss of life.
16
1. Turn off all electric power to the appliance.
2. Remove the black plastic cap located above the blower.
Do not discard cap.
3. Drill a hole through the top of the blower compartment.
NOTE: Hole diameter should be same size as sampling
tube.
4. Insert sampling tube through the drilled hole and into
the heat exchanger.
5. After a complete check and adjustment of furnace
performance, seal the drilled hole with a screw larger
than the hole. NOTE: Seal the screw threads with silicon
sealant - rated at least 500° F.
6. Plug the outside hole with the plastic cap removed in
step 3.
High Altitude Conversion
WARNING:
The reduction of input rating necessary for high
altitude installation may only be accomplished
with factory supplied orifices. Do not attempt to
drill out orifices in the field. Improperly drilled
orifices may cause fire, explosion, carbon
monoxide poisoning, personal injury or death.
High altitude conversion with this furnace depends on
the installation altitude and the heating value of the gas.
The installation of this furnace at altitudes above 2,000
feet must meet the requirements of the National Fuel Gas
Code or local jurisdiction. In Canada, the requirements for
high altitude are different and governed by CSA B149.1.
Always consult your local code authority.
This furnace is shipped from the factory with orifices and
gas regulator settings for natural gas operation at sea
level altitudes. At 2000 feet, the NFGC requires that this
appliance be derated 4% for each 1000 feet of altitude. For
example, the input needs to be reduced 8% at 2,000 feet,
12% at 3,000 feet and etc. This deration is in reference to
the input rate and gas heating value at sea level.
To derate the furnace requires knowing the heating value of
the gas at the installation site. Heating values at particular
job sites vary for two reasons:
1. The chemical mixture of the gas varies from region to
region and is expressed as the “sea level heating value”.
2. The heating value varies by altitude. For this reason,
especially in high altitude areas, the local gas utility
specifies the heating value at the residence’s gas meter
as the “local value”.
For added flexibility, two tables have been provided for
natural gas installations with high or low heating values
at sea level. Table 15, (page 30) & Table 16, (page
30) contain the manifold pressure and orifice sizes to
use at various altitudes. Table 15 (HIGH) is for natural
gas installations with a heating value of more than 1,000
Btu per cubic foot and Table 16 (LOW) is for less than
1,000 Btu per cubic foot. To determine which table to use:
1. Consult the local utility for the local heating value at
your installation site.
Floor
Control
Panel
On-Off-Fan
Switch
Alt. Fuel
Line Entry
Floor Cavity
Some codes may require installation of a manual main shut-off
valve and ground joint union external to the furnace. The shut-off
valve should be readily accessible for service and/or emergency
use. Consult the local utility or gas supplier for additional
requirements regarding placement of the manual main gas shut-off.
To Gas Supply
Figure 26. Typical Gas Piping
After the gas piping to the furnace is complete, all
connections must be tested for gas leaks. This includes all
fittings, pipe connections at the main gas valve, emergency
shutoff valve, and flexible gas connectors (if applicable).
The soap and water solution can be applied on each
joint or union using a small paintbrush. If any bubbling is
observed, the connection is not sealed adequately and
must be retightened. Repeat the tightening and soap
check process until bubbling ceases.
CAUTION:
When pressure testing gas supply lines at
pressures greater than 1/2 psig (14 inch W.C.), the
gas supply piping system must be disconnected
from the furnace to prevent damage to the gas
control valve. If the test pressure is less than or
equal to 1/2 psig (14 inch W.C.), close the manual
shut-off valve
Flue Gas Sampling
It may be necessary to take flue gas sampling from oil
and gas furnaces (M5S and M1B Series Models) in order
to check the performance after furnace installation. A
flue gas sample may be taken from the heat exchanger,
which is located behind the hole of the top-front of blower
compartment.
17
2. From Table 14, (page 30), find your local heating
value as supplied by the utility company. Follow down
the column and stop at your altitude level.
3. If your sea level heating value is HIGH, use Table 15
or if it’s LOW, use Table 16. See Example.
After changing the orifices, it is required that you measure
the gas input rate. This may be accomplished in the usual
way, by clocking the gas meter and using the local gas
heating value. See Verifying Input Rate (page 22).
IMPORTANT NOTE:
Observe the action of the burners to make sure there
is no yellowing, lifting or flashback of the flame.
LP Gas
Configuration
Black Cover
Red
Ring
Natural Gas
Configuration
Gas Control
Lever
Figure 27. Robertshaw Gas Valve
Figure 28. Honeywell Gas Valve
PRESSURE
REGULATOR
CAP
N
A
T
N
A
T
N
A
T
N
A
T
L
P
L
P
OR
OTHER SIDE
OF CAP
OUTLET PRESSURE
TAP (1/8 NPT)
INLET PRESSURE
TAP (1/8 NPT)
Installation Example
Elevation: ...................................................5,000 feet
Type of Gas: ............................................ Natural Gas
Local Heating Value of Gas: ...............................750
Determine which natural gas table to use. From Table
14, (page 30), find 750 and follow down the column,
stop at the 5,000 feet row. The heating value listed is
LOW. Table 16, (page 30) will be used to determine
orifice size and verify manifold pressure.
Conversion to Propane (LP) Gas
WARNING:
This furnace was shipped from the factory
equipped to operate on natural gas. Conversion
to LP/propane gas must be performed by qualified
service personnel using factory supplied
conversion parts. Failure to use the proper
conversion kit can cause fire, explosion, property
damage, carbon monoxide poisoning, personal
injury, or death.
WARNING:
Shut off the gas supply at the manual gas shutoff
valve, before disconnecting the electrical power.
A fire or explosion may result causing property
damage, personal injury or loss of life. Failure to
follow the safety warnings exactly could result in
serious injury, death or property damage.
WARNING:
To avoid electric shock, personal injury, or death,
turn off the electric power at the disconnect or the
main service panel before making any electrical
connections.
This furnace can be converted from factory-equipped
natural gas to liquid propane gas. Conversion of this valve
requires replacement of the burner orifice and flipping the
regulator cap to the side marked LP. The orifice required
for conversion is supplied with the furnace. See Figure 27.
For altitudes between 0 and 1,999 feet, use the factory
supplied LP orifice as shown in Table 10, (page 28).
Altitudes between 2,000 and 10,000 feet require the orifice
to be changed. Table 17, (page 30) lists the correct
orifice size and manifold pressure at different altitudes.
Atmospheric & Direct Ignition Furnaces
1. Follow the instructions in “How to Shut Off Gas - Direct
Ignition” on page 21.
2. Disconnect the gas pipe union and the electrical wires
connected to the gas valve.
3. Remove the gas valve assembly:
a. Remove screw(s) from gas valve bracket. Gas valve
and spud may be removed. Orifice is located at the
end of the spud (M1M Models)
b. Remove three (3) bolts from U-shaped manifold plate
and orifice assembly (M1B Models).
5. Replace the main orifice with the L.P. gas orifice supplied
in the envelope located by the gas valve. Verify the
orifice size matches the nameplate or Table 10, (page
28).
18
6. For Honeywell gas valves with the regulator converter:
a. Unscrew the pressure regulator cap and check for
the letters NAT or LP. See Figure 27 (page 17).
b. Invert the cap and tighten until snug.
7. For Robertshaw gas valves with the regulator converter:
a. Remove the black cover and unscrew the converter
located on top of the gas valve. See Figure 28 (page
17).
b. Invert the converter. For LP, the red ring will be located
at the bottom and the LP stamping on the converter
will appear right side up.
c. Screw converter back into the regulator, hand tight
plus 1/8 turn. Replace the black cover on the converter
top to protect the threads.
8. Reassemble the burner assembly into the furnace.
9. Reconnect the gas piping and electrical wires to the
gas valve.
10. Open the manual shut-off valve and follow the M1M
Operating Instructions on page 20
Measuring the Supply Gas Pressure
To obtain an accurate pressure reading, turn off all
gas appliances (i.e. Dryers, water heaters, stoves,
etc.) at their ON/OFF control or individual gas valves.
1. Remove the inlet pressure plug from the INLET side
of the gas valve with a 3/16 Allen wrench. See Figure
27 (page 17).
2. Install a 1/8 NPT fitting, which is compatible with a
manometer or similar pressure gauge.
3. Connect the manometer or pressure gauge to the inlet
pressure tap.
4. Turn on all electrical power to the furnace.
5. Turn the main gas supply valve (on the outside of the
unit) to the ON position.
6. Start the furnace by adjusting the thermostat to it’s
highest setting. Allow the furnace to run for 10 minutes.
7. Check the incoming gas line pressure. Propane gas
furnaces must be between 11.0”-14.0” W.C. Natural
gas installations must be between 4.5”-10.0” W.C. If
the pressure is not between these specified ranges,
contact your local gas supplier for adjustment.
8. Adjust the thermostat to it’s lowest setting and allow
the unit to cycle off.
9. Turn the main gas supply valve (on the outside of the
unit) to the OFF position.
10. Turn off all electrical power to the furnace.
11. Disconnect the manometer or pressure gauge.
12. Remove the NPT fitting and reinstall the inlet pressure
plug. NOTE: To prevent cross threading, hand tighten
the plug first, then tighten with 3/16 Allen wrench.
Measuring the Manifold Pressure
The manifold pressure must be measured by installing a
pressure gauge (Manometer, Magnehelic Meter, etc.) to
the outlet end of the gas valve.
1. Remove the manifold pressure plug from the outlet side
of the gas valve with a 3/16 Allen wrench.See Figure
27 (page 17).
2. Install a 1/8 NPT fitting, which is compatible with a
Manometer or similar pressure gauge.
3. Connect the manometer or pressure gauge to the pipe
thread fitting.
4. Start the furnace by adjusting the thermostat 5 degrees
above room temperature. Allow the furnace to operate
for 3 minutes.
5. Measure the manifold pressure on the manometer or
pressure gauge. Compare the measured value to the
value in Table 15, (page 30), Table 16, (page 30),
or Table 17, (page 30).
6. Replace the cap so that the letters facing up represent
the type of gas being used for the furnace. See Figure
27 (page 17).
7. Adjust the thermostat to its lowest setting.
8. Turn off the main gas supply to the unit at the manual
shut-off valve, which is located outside of the unit.
9. Turn off all of the electrical power to the furnace.
10. Disconnect the manometer or pressure gauge.
11. Remove the 1/8 NPT fitting and reinstall the manifold
pressure plug. NOTE: To prevent cross threading,
hand tighten the plug first then tighten with 3/16 Allen
wrench.
Oil Tank & Piping Installation
The following procedures are recommended as good
practice. However, requirements of local codes and
ordinances, H.U.D. Manufactured Home and Safety
Standards or National Fire Protection Association must be
satisfied, where they apply, for an approved installation.
Use a tank capacity suitable for the application with a
weatherproof, capped fill opening and a shielded vent
to let in air as fuel is used.
The inside of the tank must be clean before filling. All
water, rust, sediment, and debris must be flushed out.
A fuel or tank gauge is recommended for easy checking
of the fuel level. Check the gauge reading with a dipstick.
See Figure 29 (page 19).
Locate the storage tank conveniently near the home.
If the fuel tank is installed above ground, the tank may
rest 3 to 4 inches off the ground. Fuel tanks may also
be buried if properly coated to resist corrosion. The
vertical dimension from the bottom of the fuel tank to
the fuel pump must not exceed 10 feet.
Keep the tank filled, especially in the summer to reduce
the accumulation of condensation.
One-Line System
The One-Line System is highly recommended where
vertical lift, from bottom of tank to pump, is less than 8
feet. See Figure 29 (page 19). A single line hookup
has the advantage of lower cost and quieter operation.
Two-Line System
If a Two-Line system is used or if oil is taken from the
bottom of the tank, a filter is recommended. A Two-Line
system should only be used if vertical lift exceeds 8 feet.
1. Install the oil feed line as outlined in steps 1 - 6 below.
2. Install the oil pump bypass plug in the bottom return
port.
3. Route the return line up through the furnace base to
the return port of the pump. Route the other end of the
line to the tank, using 3/8” O.D. copper tubing or 1/4”
pipe with the ends capped.
19
4. Insert the return line through the second opening in the
duplex bushing. If the bottom of the tank is lower than
the pump intake, the tube should be inserted three or
four inches from the tank bottom. If the bottom of the
tank is higher than the pump intake, the return line
should extend not more than 8” inside the tank.
Fuel line Hook-Up
1. Use a 3/8” O.D. copper tubing for the fuel line.
NOTE: Cap the end with tape to keep out dirt while the
line is being routed.
2. Install duplex bushing for two 3/8” lines in the top fitting
of the tank. See Figure 29.
3. Insert one end of the tubing through the duplex bushing
until it is three to five inches from the bottom drain.
Tighten the bushing.
4. Route the line where it will not incur any damage. Make
bends gradual and avoid kinks which might restrict oil
flow.
5. Open the furnace door and connect the oil line to the
intake port on the pump. Tighten other port plugs on
the pump. NOTE: Verify the oil line is airtight! Air leaks
can cause the pump to lose prime and will create other
problems such as nozzle failure, odors, rumbling noise,
and false safety shutdown.
6. Insert the short length of the copper tube level with the
bottom of the duplex bushing. Form the tube into an
inverted “U” to serve as a vent.
Fuel Line Bleeding
To eliminate problems caused by air in the oil line, all
connections in the oil supply line and all plugs, nuts,
and fittings on the pump must be airtight. NOTE: This
includes the nut that covers the pressure adjustment. It
is important that the hook-up be done carefully and with
a good flaring tool.
Prepare the burner for priming by attaching a clear plastic
hose over the bleed port fitting and fully opening the pump
bleed port. Use a suitable container to collect purged oil.
To ensure continuous operation, use a wire to jump
terminals T-T (or F-F) on the primary control while burner
is running.
Priming furnaces equipped with Honeywell
R7184 primary control:
1. While the ignition is on, press for 1/2 second (or less),
and release the reset button. The lockout time will be
extended to 4 minutes.
2. If prime is not established within the 4 minutes, the
control will lock out. Press the reset button to reset the
control.
3. Repeat steps 1 & 2 (if needed) until the oil pump is fully
primed.
Priming furnaces equipped with Beckett 7505
primary control
1. After the burner starts, press and hold the reset button
until the yellow LED turns on (15 seconds). This indicates
that the button has been held long enough.
2. Release the reset button. The yellow LED will turn off
and the burner will start up again.
3. At burner start up, click the reset button while the igniter
is still on. This transitions the control to a dedicated pump
prime mode, during which the motor, igniter and valve
are powered for 4 minutes. The yellow LED will be on.
NOTE: If prime is not established during the four minute
pump prime mode, repeat step 3 until the oil pump is
fully primed.
4. When oil flow is clear and free of air bubbles, close
air-bleed valve and tighten. NOTE: Air bleed out time
will varies depending on length of oil line, number of
bends, etc.
Figure 29. Typical Oil Piping for Above Ground (Single-Line) Supply
Top of Tank
8 ft.
Shut-off
Valve
Optional
Fuel
Filter
Alternate
Fuel Line
Entry
Control
Panel
Oil
Furnace
On-Off-Fan
Switch
Floor Cavity
Oil-Gun
Burner
Floor
Flue Gas
Sampling
Hole
Drain
End of Oil Supply Line
3" to 5" Above Bottom Drain
Guide
Pipe
Gauge
Vent with cap
2" Duplex
Bushing
2" Fill
3/8" Oil Supply Line
NOTE: Additional venting may be
required if tank is filled rapidly.
4 GPH 100-150 PSI 3450 RPM
3 GPH 150-200 PSI 3450 RPM
VALVE ON DELAY
NO. 2 & LIGHTER FUEL
USE ONLY WITH
INLET
BY-PASS
Exclusively for Beckett
Made by Suntec
INLET
NO. 2 FUEL
A2EA-6520
Becket
t
Nozzle Port
3/16 Flare Fitting
Bypass Solenoid Valve
Cordset
Inlet Port
1/4 NPTF
Bleed & Gauge Port
Pressure
Adjustment
Screw
Inlet Port
1/4 NPTF
Return Port - Install 1/6” Bypass Pipe
Plug for 2-pipe System Only.
(Use 5/32” Allen Wrench)
If fuel pump fails to lift oil, check for air
leaks and tighten all fuel fittings.
Reprime fuel pump by injecting fuel oil into
optional (top) return port. Replace return
port plug and repeat priming procedure.
Some codes may require installation of a manual main shut-off
valve and ground joint union external to the furnace. The shut-off
valve should be readily accessible for service and/or emergency
use. Consult the local utility or gas supplier for additional
requirements regarding placement of the manual main gas shut-off.
20
Fuel Oil Type
WARNING:
Do not use gasoline, crankcase oil, or any oil
containing gasline. Failure to keep supply of oil
clean by various procedures described above
may cause failure of certain components such as
the fuel pump gears, check valve, shaft seal, or
burner nozzle which may result in a burner fire.
Do not use fuel oil heavier than Grade No. 2. In areas
where the oil supply is subject to low temperatures, Grade
No. 1 may be used.
STARTUP & ADJUSTMENTS
PLEASE READ ALL SAFETY INFORMATION
BEFORE LIGHTING THE FURNACE
WARNING:
FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly could
result in serious injury or property damage.
Installation and service must be performed
by a qualified installer, service agency or the
gas supplier.
Do not store or use gasoline or other
flammable vapors and liquids in the vicinity
of this or any other appliance.
WHAT TO DO IF YOU SMELL GAS
Do not try to light any appliance.
Do not touch any electrical switch; do not
use any phone in your building.
Leave the building immediately.
Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s
instructions.
If you cannot reach your gas supplier, call
the fire department.
WARNING:
Before placing the furnace in service, it must be
checked to ensure it is equipped for the type of gas
being used. The burner flame must be observed
and adjusted if necessary. Failure to observe this
caution may result in unsafe operation, explosion
and/or fire, or asphyxiation. See the Gas Supply
and Combustion Air sections.
The first operation of the furnace after any home
setup must be performed by a qualified service
technician.
BEFORE STARTUP: Smell all around the furnace for
gas and next to the floor. Some gas is heavier than air
and may settle on the floor.
• M1B Units Only: Use only your hand to push in the gas
control lever. Never use tools. If the lever will not push
in by hand, don’t try to repair it. Force or attempted
repair may result in a fire or explosion. Call a qualified
service technician.
• Do not use this furnace if any part has been under
water. Immediately call a service technician to inspect
the furnace and to replace any part of the gas valve or
control system which has been under water.
WARNING:
Close the hinged fire door. If door is left open
or spring is broken it may allow products of
combustion into the living space by the furnace
blower, resulting in possible asphyxiation.
WARNING:
Should overheating occur, or the gas supply fails
to shut off, shut off the manual gas valve to the
furnace before shutting off the electrical supply.
M1M Operating Instructions
(Direct Ignition Furnaces)
Direct ignition furnaces do not have a pilot. Ignition is
accomplished by a hot surface ignitor. A circuit board
takes care of all timing functions. After lighting, the circuit
board uses the ignitor as a flame sensor, shutting off gas
should the flame go out. There are no external relays or
timing devices. Do not try to light this furnace by hand.
The circuit board is not field serviceable.
1. Set the thermostat to the lowest setting.
2. Turn off all electric power to the appliance.
3. Remove the furnace door and turn off the gas valve:
Honeywell: push in and turn the gas control knob
clockwise to OFF. See Figure 30.
Robertshaw: push the gas control lever (Do not force!)
to the OFF position. See Figure 28, (page 17).
4. Wait ten (10) minutes to clear out any gas. If you smell
gas, STOP! and follow the Safety Information. If you
do not smell gas, proceed to step 5.
5. Set the thermostat MODE the ON position.
Figure 30. Direct Ignition Gas Valve - Honeywell
GAS CONTROL KNOB
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68

Broan M1 Guide d'installation

Taper
Guide d'installation
Ce manuel convient également à

dans d''autres langues