Maytag M1 Guide d'installation

Marque: Maytag

Modèle: M1

Taper: Guide d'installation

Ce manuel convient également à

M1B, M1M & M5S Series

Downﬂow, Direct Vent (Sealed Combustion)

Forced Air Gas & Oil Furnaces

For installation in:

• Manufactured Homes

• Recreational Vehicles, Park Models, & Manufactured

Buildings

• Modular Homes / Buildings

INSTALLATION INSTRUCTIONS

WARNING CAUTION

FIRE OR EXPLOSION HAZARD

• Failure to follow safety warnings exactly could

result in serious injury or property damage.

• Installation and service must be performed

by a qualiﬁed installer, service agency or the

gas supplier.

• Do not store or use gasoline or other

ﬂammable vapors and liquids in the vicinity

of this or any other appliance.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not

use any phone in your building.

• Leave the building immediately.

• Immediately call your gas supplier from a

neighbors phone. Follow the gas suppliers

instructions.

• If you cannot reach your gas supplier, call

the ﬁre department.

HUD Manufactured Home Construction and

Safety Standards (3280.714) prohibit the use

of noncertiﬁed air conditioning or heat pump

equipment with this furnace. It is strongly

recommended that manufactured housing

air conditioning components from Nortek

Global HVAC be selected to provide a matched

system speciﬁcally designed to meet these

requirements.

The cutting, splicing or modifying of any

internal electrical wiring may void product

warranties and create a hazardous condition.

Failure to comply with these standards could

also provide inadequate heating or cooling

performance and cause structural damage to

a manufactured home.

Please contact your local distributor for help.

A directory of Nortek Global HVAC factory

authorized servicers is located in the furnace

homeowner packet.

Reference: HUD Manufactured Home

Construction and Safety Standards 3280.714.

DO NOT DESTROY. PLEASE READ CAREFULLY & KEEP IN A SAFE PLACE FOR FUTURE REFERENCE.

TABLE OF CONTENTS

IMPORTANT SAFETY INFORMATION ..................... 3

REQUIREMENTS & CODES ..................................... 3

GENERAL INFORMATION ........................................ 4

Minimum Clearances ............................................... 4

Applications ............................................................. 4

Unit Location ............................................................ 6

CIRCULATING AIR REQUIREMENTS ...................... 6

Return Air ................................................................. 6

Supply Air ................................................................ 6

FURNACE INSTALLATION ....................................... 7

General Information ................................................. 7

Locating & Cutting Duct Openings ........................... 7

Standard Duct Connector Installation ...................... 9

Alternate Attachment Method ................................ 9

Round Duct Connector Installation .......................... 9

Installing the Furnace .............................................. 9

ROOF JACK INSTALLATION ................................... 10

Roof Jack Selection ................................................. 10

Locating & Cutting Roof / Ceiling Openings ............ 10

Installing The Roof Jack .......................................... 11

Installation of Transit-Mode Venting System ........... 11

Before home is moved to site .................................. 11

Installation of Transit-Mode Venting System ........... 12

After home is moved to site ..................................... 12

ELECTRICAL INFORMATION .................................. 13

Line Voltage Wiring .................................................. 13

Connecting Power Supply Wires ........................... 13

Low Voltage Wiring .................................................. 13

Connecting Thermostat Wires ............................... 13

Verifying Anticipator Setting .................................. 13

Grounding ................................................................ 14

FUEL SUPPLY & PIPING .......................................... 15

Leak Check .............................................................. 15

Flue Gas Sampling .................................................. 16

High Altitude Conversion ......................................... 16

Conversion to Propane (LP) Gas ............................. 17

Atmospheric & Direct Ignition Furnaces ................ 17

Measuring the Supply Gas Pressure.....................18

Measuring the Manifold Pressure..........................18

Oil Tank & Piping Installation ................................... 18

One-Line System .................................................. 18

Two-Line System...................................................18

Fuel line Hook-Up .................................................... 19

Fuel Line Bleeding ................................................... 19

Priming furnaces equipped with Honeywell...........19

R7184 primary control ........................................... 19

Priming furnaces equipped with Beckett 7505

primary control.......................................................19

Fuel Oil Type ........................................................... 20

STARTUP & ADJUSTMENTS ................................... 20

M1M Operating Instructions ..................................... 20

How to Shut Off Gas - Direct Ignition Models........21

M1B Operating Instructions ..................................... 21

How to Shut Off Gas Gun Models ......................... 21

M5S Operating Instructions ..................................... 21

How to Shut Off Oil Gun Models ........................... 22

Verifying Input Rate ................................................. 22

Verifying & Adjusting Temperature Rise .................. 22

Burner Adjustments ................................................. 22

Gas Pressure ........................................................ 22

Combustion Air ........................................................ 22

Gas Gun (M1B Models).........................................23

Oil Gun Only (M5S Models) .................................. 23

Electrode Setting (Oil Gun Only) ............................. 23

Switching Ignition Control between Interrupted

and Intermittent Duty ............................................... 23

OPERATING SEQUENCE ......................................... 23

Direct Ignition Furnaces (M1M Models) ................... 23

Gas Gun Furnaces (M1B Models) ........................... 23

Oil Gun Furnaces (M5S Models) ............................. 23

TROUBLESHOOTING ............................................... 24

Direct Ignition Furnaces (M1M Models) &

Gas Gun Furnaces (M1B Models) ........................... 24

Oil Gun - Honeywell R7184 or Beckett 7505

Controls Only - M5S Series ..................................... 25

FURNACE CONTROLS & FUNCTIONS ................... 26

MAINTENANCE ......................................................... 27

Installer Information ................................................. 27

Additional Oil Furnace Maintenance ........................ 27

OPTIONAL ACCESSORIES ...................................... 27

Optional Add-On Air Conditioning ............................ 27

FIGURES & TABLES ................................................. 28

Table 10. M1/M5 Furnace Speciﬁcations -

Factory Settings .................................................... 28

Table 11. A/C Blower Speed Selection Chart ....... 28

Gas Information ....................................................... 29

Table 12. Gas Flow Rates ..................................... 29

Table 13. Gas Pipe Capacities .............................. 29

Table 17. High Altitude Deration Chart for

Propane Gas ......................................... 30

Electrical Information ............................................... 31

Figure 35. Gas Direct Ignition Furnace, Heating &

A/C Ready - All M1M Models ............... 31

Figure 36. Gas and Oil Furnaces, A/C Ready -

M1B & M5S (066, 086) Models ............ 32

INSTALLATION CHECKLIST .................................... 36

IMPORTANT SAFETY INFORMATION

Safety markings are used frequently throughout this

manual to designate a degree or level of seriousness and

should not be ignored. WARNING indicates a potentially

hazardous situation that if not avoided, could result in

personal injury or death. CAUTION indicates a potentially

hazardous situation that if not avoided, may result in minor

or moderate injury or property damage.

WARNING:

The safety information listed below must be

followed during the installation, service, and

operation of this furnace. Failure to follow safety

recommendations could result in possible

damage to the equipment, serious personal

injury or death.

WARNING:

Do not install this furnace if any part has been

submerged under water. A ﬂood damaged furnace

is extremely dangerous. Attempts to use the

furnace may result in ﬁre or explosion. A qualiﬁed

service agency should be contacted to inspect the

furnace and to replace any electrical or control

system parts that have been wet or under water.

CAUTION:

Operating gas furnaces in construction

environments can cause a variety of problems

within the furnace and may significantly

reduce the life or the performance of the

furnace. Therefore operating the furnace during

construction is not permitted and will void the

warranty.

REQUIREMENTS & CODES

• This furnace must be installed in accordance with

these instructions, all applicable local building codes

and the current revision of the National Fuel Gas Code

(NFPA54/ANSI Z223.1) or the Natural Gas and Propane

Installation Code, CAN/CSA B149.1.

• Use only with type of gas approved for this furnace.

Refer to the furnace rating plate.

• Install this furnace in accordance to the minimum

clearances to combustible materials listed in Table 1,

(page 5).

• Provide adequate combustion and ventilation air to the

furnace space as speciﬁed on page 6 and page 22.

Do not block or obstruct air openings on the furnace,

air openings to the area where the furnace is installed,

or the space around the furnace.

• Combustion products must be discharged outdoors.

Connect this furnace to an approved vent system, as

speciﬁed on page 10.

• Never test for gas leaks with an open ﬂame. Use

a commercially available soap solution to check all

connections. See page 15.

• This furnace is designed to operate with a maximum

external pressure rise of 0.5 inches of water column.

NOTE 1: The static pressure measurement should not

include the coil (if applicable). Consult Table 10, (page

28) and the rating plate for the proper circulating air

ﬂow and temperature rise.

NOTE 2: It is important that the duct system be designed

to handle the desired ﬂow rate and external pressure

rise. An improperly designed duct system can result in

nuisance shutdowns, and comfort or noise issues.

• When supply ducts carry air circulated by the furnace

to areas outside the space containing the furnace, the

return air shall also be handled through the front door

of the furnace. Make sure there is sufﬁcient return air

through the door. See return air connections page 6.

• Additional information listed below is for reference

purposes only and does not necessarily have jurisdiction

over local or state codes. Always consult with local

authorities before installing any gas appliance.

Combustion & Ventilation Air

• US: National Fuel Gas Code (NFGC), Air for Combustion and

Ventilation

• CANADA: Natural Gas and Propane Installation Codes

(NSCNGPIC), Venting Systems and Air Supply for Appliances

Duct Systems

• US and CANADA: Air Conditioning Contractors Association

(ACCA) Manual D, Sheet Metal and Air Conditioning

Contractors National Association (SMACNA), or American

Society of Heating, Refrigeration, and Air Conditioning

Engineers (ASHRAE) Fundamentals Handbook

Electrical Connections

• US: National Electrical Code (NEC) ANSI/NFPA 70

• CANADA: Canadian Electrical Code CSA C22.1

Gas Piping & Gas Pipe Pressure Testing

• US: NFGC and National Plumbing Codes

• CANADA: NSCNGPIC

General Installation

• US: Current edition of the NFGC and the NFPA 90B. For

copies, contact the National Fire Protection Association Inc.,

Batterymarch Park, Quincy, MA 02269; or American Gas

Association, 400 N. Capitol, N.W., Washington DC 20001 or

www.NFPA.org

• CANADA: NSCNGPIC. For a copy, contact Standard Sales,

CSA International, 178 Rexdale Boulevard, Etobicoke

(Toronto), Ontario, M9W 1R3 Canada

Safety

• US: (NFGC) NFPA 54–1999/ANSI Z223.1 and the Installation

Standards, Warm Air Heating and Air Conditioning Systems

ANSI/NFPA 90B.

• Federal Manufactured Home Constructions & Safety Standard

(H.U.D. Title 24, Part 3280.707[a][2])

• The Standard for Manufactured Home Installations

(Manufactured Home Sites, Communities, and Set-Ups) ANSI

A225.1 and/or CAN/CSA-2240 MH Series).

• American National Standard (ANSI-119.2/NFPA-501C) for

all recreational vehicle installations.

• CANADA: CAN/CSA-B149.1 and .2–M00 National Standard

of Canada. (NSCNGPIC)

• The Commonwealth of Massachusetts requires

compliance with regulation 248 CMR 4.00 and 5.00 for

installation of through – the – wall vented gas appliances

as follows:

1. For direct-vent appliances, mechanical-vent heating

appliances or domestic hot water equipment, where the

bottom of the vent terminal and the air intake is installed

below four feet above grade the following requirements

must be satisﬁed:

a.) A carbon monoxide (CO) detector and alarm shall be

placed on each ﬂoor level where there are bedrooms.

The detector shall comply with NFPA 720 (2005

Edition) and be mounted in the living area outside

the bedroom(s).

b.) A (CO) detector shall be located in the room that

houses the appliance or equipment and shall:

• Be powered by the same electrical circuit as the

appliance or equipment. Only one service switch shall

power the appliance and the (CO) detector;

• Have battery back-up power;

• Meet ANSI/UL 2034 Standards and comply with

NFPA 720 (2005 Edition); and Approved and listed

by a Nationally Recognized Testing Laboratory as

recognized under 527 CMR.

c.) A Product-approved vent terminal must be used, and

if applicable, a product-approved air intake must be

used. Installation shall be in strict compliance with the

manufacturer’s instructions. A copy of the installation

instructions shall remain with the appliance or

equipment at the completion of the installation.

d.) A metal or plastic identiﬁcation plate shall be mounted

at the exterior of the building, 4 feet directly above

the location of vent terminal. The plate shall be of

sufﬁcient size, easily read from a distance of eight

feet away, and read “Gas Vent Directly Below”.

2. For direct-vent appliances, mechanical vent heating

appliances or domestic hot water equipment where the

bottom of the vent terminal and the air intake is installed

above four feet above grade the following requirements

must be satisﬁed:

a.) A (CO) detector and alarm shall be placed on each

ﬂoor level where there are bedrooms. The detector

shall comply with NFPA 720 (2005 Edition) and be

mounted in the living area outside the bedroom(s).

b.) The (CO) detector shall:

• Be located in the room that houses the appliance or

equipment;

• Be hard-wired, battery powered or both.

• Shall comply with NFPA 720 (2005 Edition).

c.) A product-approved vent terminal must be used, and

if applicable, a product-approved air intake must be

used. Installation shall be in strict compliance with the

manufacturer’s instructions. A copy of the installation

instructions shall remain with the appliance or

equipment at the completion of the installation.

GENERAL INFORMATION

CAUTION:

• Do Not alter or modify this furnace or any of

its components.

• Never attempt to repair damaged or inoperable

components. This may cause unsafe operation,

explosion, ﬁre and/or asphyxiation.

• If furnace malfunctions or does not operate

properly, contact a qualiﬁed service agency

or gas utility for assistance.

Minimum Clearances

This heating appliance must be installed with clearances

not less than the minimums listed in Table 1, (page 5).

This furnace must be installed with ample clearance for

easy access to the air ﬁlter, blower assembly, burner

assembly, controls, and vent connections. See Figure 1,

Figure 2, and Figure 3 (page 5).

• The dimensions of the room or alcove must be able to

accommodate the overall size of the furnace and the

installation clearances listed in Table 1 and in Figure 4

(page 5).

• Alcove installations: minimum 18” clearance at front

of furnace shall be provided for future servicing. A

removable access panel should be installed between

top of the furnace door frame and the ceiling.

• Closet installations must use a louvered door having

a minimum free area of 235 in

when located 6” from

furnace or 390 in

for 5 ton ready M1/M5 furnaces. For

special clearance between 1” - 6”, requirements are a

louvered door with a minimum of 250 in

free area, with

the openings in the closet door in line with the louvered

openings in the furnace door. A fully louvered closet

door may be used. See Circulating Air Requirements

section (page 6).

• The furnace must be kept free and clear of insulating

material. Examine the furnace area when the furnace is

installed or when insulation is added. Insulating material

may be combustible.

Applications

M1 Series gas and M5 Series oil furnaces are listed direct

vent (sealed combustion), downﬂow heating appliances for

manufactured (mobile) homes and recreational vehicles.

The furnace must be located so that venting can be

properly achieved.

Air conditioning may be added to structures with M1/M5

series furnaces using air conditioning or conventional

units. This Installation Instruction manual includes

special requirements for incorporation of air conditioning

equipment to the M1/M5 series of furnaces. See Table

11, (page 28).

Multi-speed blower assemblies shown in Table 2, (page

5), have been certiﬁed for ﬁeld installation in M1/M5

Series furnaces.

“A”- 56"

19 3/4"

23 3/4"

“B”- 76"

“A” Model without Coil Cabinet

“B” Model with Coil Cabinet

Figure 4. Overall Dimensions

Table 1. Minimum Clearances

ALL MODELS CLOSET ALCOVE

Front 6” 18”

Back 0” 0”

Sides 0” 0”

Roof Jack 0” 0”

Top 6” 6”

Top and Sides of Duct 0” 0”

Bottom of Duct — —

A Cabinet (w/ coil box) 0” 0”

A Cabinet (w/o coil box) 1/4” 1/4”

B Cabinet 0” 0”

Table 2. Blower Assemblies

PART

NO.

BLOWER / MOTOR ASSEMBLY

A/C CAPACITY

(TONS)

BLOWER

WHEEL

MOTOR

(HP)

903413 11 x 8 1/2 2, 2½, 3 & 4

903890 11 x 8 3/4 2, 2½, 3, 4 & 5

Removable access

panel should be

installed above

furnace door frame

to access roof jack

Nearest

Wall or

Partition

18"

(457 mm)

6" (152 mm)

Top Clearance

0" Side

Clearance

to Furnace

Cabinet

6" (152 mm)

Top Clearance

0" Side

Clearance

to Furnace

Cabinet

Provide min. 235

sq. in. (1516 cm )

open free area in

front or side wall

In closet

door

located

at top,

center

or bottom

CLOSET DOOR

6" (152 mm)

Top Clearance

Provide min. 250

sq. in. (1613 cm )

open free area in

front or side wall

a fully

louvered

door may

be used

CLOSET DOOR

(152 mm)

(25 mm)

0" Side

Clearance

to Furnace

Cabinet

in closet

door

Figure 2. Closet Installation

Figure 3. Special 1” Clearance

Figure 1. Alcove Installation

Unit Location

• The furnace shall be appropriately located to the supply

and return air distribution system (page 6). Sides and

back of the furnace may be enclosed by wall framing.

See Minimum Clearances section on page 4.

• The furnace installation is only intended for free air return

through the furnace door louvers. DO NOT connect a

ducted return air system directly to the furnace. Improper

installation may create a hazard and damage equipment,

as well as void all warranties.

• Furnace may be installed on combustible ﬂooring when

using manufacturer approved duct connectors. See

page 6.

• When installed in a residential garage, the furnace must

be positioned so the burners and the source of the

ignition are located no less than 18 inches above the

ﬂoor and protected from physical damage by vehicles.

CIRCULATING AIR REQUIREMENTS

WARNING:

Do not allow combustion products to enter the

circulating air supply. Failure to prevent the

circulation of combustion products into the

living space can create potentially hazardous

conditions including carbon monoxide poisoning

that could result in personal injury or death.

The surface that the furnace is mounted on must

provide sound physical support of the furnace

with no gaps, cracks or sagging between the

furnace and the ﬂoor or platform.

Circulating air ductwork must not be connected

to any other heat producing device such as a

ﬁreplace insert, stove, etc. This may result in ﬁre,

explosion, carbon monoxide poisoning, personal

injury, or property damage.

Return Air

U.S.A. home manufacturers shall comply with all of the

following conditions to have acceptable return air systems

for closet installed forced air heating appliances:

• The return air opening into the closet shall not be less

than speciﬁed in the appliance’s listing.

• The cross-sectional area of the return duct system

leading into the closet, when located in the ﬂoor or

ceiling shall not be less than 235 in

(or 390 in

for M1/

M5 Furnaces with 5 ton blower kits).

CAUTION:

HAZARD OF ASPHYXIATION: Do not cover or

restrict return air opening.

• Means shall be provided that prevent inadvertent closure

of ﬂat objects placed over the return air opening located

in the ﬂoor of the closet (versus the vertical front or side

wall).

• The total free area of openings in the ﬂoor or ceiling

registers serving the return air duct system must be at

least 235 in

. At least one register should be located

where it is not likely to be covered by carpeting, boxes

and other objects.

• Materials located in the return duct system must have a

ﬂame spread classiﬁcation of 200 or less. This includes

a closet door if the furnace is in a closet.

• Noncombustible pans having 1” upturned ﬂanges are

located beneath openings in a ﬂoor duct system.

• Wiring materials located in the return duct system shall

conform to Articles 300-22 of the National Electrical

Code (ANSI C1/NFPA-70).

• Gas piping is not run in or through the return duct system.

CAUTION:

HAZARD OF ASPHYXIATION: Negative pressure

inside the closet, with closet door closed and

the furnace blower operating on high speed,

shall be no more negative than minus 0.05 inch

water column.

• Test the negative pressure in the closet with the air-

circulating fan operating at high speed and the closet

closed. The negative pressure is to be no more negative

than minus 0.05 inch water column.

• Air conditioning systems may require more duct register

and open louver area to obtain necessary airﬂow.

Supply Air

For proper air distribution, the supply duct system must be

designed so that the static pressure measured external

to the furnace does not exceed the listed static pressure

rating shown on the furnace rating plate.

Location, size, and number of registers should be selected

on the basis of best air distribution and ﬂoor plan of

the home. The supply air must be delivered to the

conditioned space by duct(s) secured to the furnace

casing, running full size and without interruption.

Three typical distribution systems are shown in Figure 5

Figure 5. Typical Supply Duct System

A Single trunk duct

Dual trunk duct

w/crossover connector

Transition duct

w/branches

FURNACE INSTALLATION

NOTE: These Installation procedures are suggested for

typical furnace installations. Since each installation is

different, the sequence of instructions may differ from

the actual installation. Only qualiﬁed HVAC technicians

should install this furnace.

The installer must be familiar with and comply with all

codes and regulations applicable to the installation of

these heating appliances and related equipment. In

the absence of local codes, the installation must be in

accordance with the current provisions of one or more of

the following standards.

• Federal Manufactured Home Constructions & Safety

Standard (H.U.D. Title 24, Part 3280.707[a][2])

• American National Standard (ANSI-119.2/NFPA-501C)

for all recreational vehicle installations.

• American National Standard (ANSI-Z223.1/NFPA-54)

and/or CAN/CSA B149 for all gas-ﬁred furnace models.

• American National Standard (ANSI-Z95.1/NFPA-31)

and/or CSA B139 for all oil-ﬁred furnace models.

• American National Standard (ANSI-C1/NFPA-70) and/or

CSA 22.1 Canadian Electric Code Part 1 for all electrical

ﬁeld wiring.

• Units have been certiﬁed under standards UL 307A & B,

UL727-1999, ANSI Z21.47/CSA 2.3, and CSA B140.10.

General Information

• The furnace must be leveled at installation and attached

to a properly installed duct system. Do not use the

back of the furnace for return air. See page 6

for circulating requirements.

• The furnace must be installed so that all electrical

components are protected from water

• The dimensions of the room or alcove must be able to

accommodate the overall size of the furnace and the

installation clearances listed in Table 1, (page 5)

and Figure 1 (page 5)

• The furnace must be installed upstream from a

refrigeration system.

• M1 series (gas) and M5 series (oil) furnaces are

certiﬁed for use on wood ﬂooring or supports, but must

be installed on top of a duct connector. This factory

supplied accessory must be installed in the ﬂoor cavity

and attached to the supply air duct before the furnace

is installed.

Locating & Cutting Duct Openings

Floor cut-outs and fuel line holes must be carefully located

to avoid misalignment of the furnace, and vent piping.

To locate standard ducts see Figure 6. For round ducts,

see Figure 7.

1. Measure 10” from the rear wall or alcove and mark the

centerline of the cut-out on the ﬂoor.

2. Using the centerline as a starting point, draw the rest

of the duct cut-out to the dimensions shown in Figure

6 or Figure 7.

3. Cut out the ﬂoor opening 1/16” larger than the actual

cutout drawn. This will allow some clearance when

installing the duct connector.

4. Measure from the top of the ﬂoor down to the top of the

supply air duct to obtain the depth of the ﬂoor cavity.

FLOOR CUT-OUT

FOR STANDARD

DUCT CONNECTORS

24"

23 1/4"

21 3/4"

14 1/2"

2 1/4"

2 3/4"

20"

CUT-OUT FOR

OPTIONAL

COOLING COIL

REAR WALL OF CLOSET OR ALCOVE

1 3/4"

3/4"

10"

FURNACE OUTLINE

14 1/2"

ALT FUEL-LINE

ENTRY 1 1/4" Dia.

FURNACE

OUTER

DOOR

FUEL

LINE

1 3/4"

3/4"

1 7/8"

2 7/8"

Figure 6. Cut-Out Dimensions for

Standard Duct Connectors

FLOOR

CUT-OUT FOR

ROUND DUCT

(14 1/4” DIAMETER)

24"

23 1/4"

21 3/4"

20"

CUT-OUT FOR

OPTIONAL

COOLING COIL

ALT FUEL-LINE

ENTRY 1 1/4" Dia.

FURNACE

OUTER

DOOR

REAR WALL OF CLOSET OR ALCOVE

FUEL

LINE

1 3/4"

3/4"

10"

FURNACE OUTLINE

1 3/4"

10"

3/4"

1 7/8"

2 7/8"

Figure 7. Cut-Out Dimensions for

Round Duct Connectors

Bend tabs

up 90°

Mounting Plate

Duct

Connector

Tabs

Supply

Air Duct

Hole for

Gas Line

Wood Floor

Figure 8. Standard Duct Connector Installed

IF FLOOR

CAVITY

“X” IS:

DUCT CONNECTOR

TYPE & PART NUMBER

STANDARD DUCT ROUND DUCT

7/8” / (22) 901987A 904008

2” / (51) 901988A N/A

4-1/4” / (108) 901989A 904010

6-1/4” / (159) 901990A 904011

8-1/4” / (210) 901991A 904012

10-1/4” / (260) 901992A 904013

12-1/4” / (311) 901993A 904014

NOTE: Dimensions shown as Inches / (Millimeter)

Table 3. Duct Connector Sizes

DUCT CONNECTOR

SUPPLY

AIR DUCT

BEND TABS TIGHTLY

AGAINST SUPPLY AIR DUCT

Figure 10. Duct Connector Tabs

OPTION 1 OPTION 2

Supply

Air Duct

Fold Flap Here

Remove

this

Flap

Remove

this

Flap

Cut Here

Fold Flap Here

Figure 11. Narrow Air Duct Openings

DUCT

CONNECTOR

SCREWS

MOUNTING

PLATE

FUEL LINE

HOLE

FUEL LINE

HOLE

14” SUPPLY

CONNECTION

Figure 13. Round Duct Connector Installed

MTG. PLATE TABS

SLIDE FURNACE

ALL THE WAY BACK

ONTO MTG. PLATE

SUPPLY AIR DUCT

Knockout Over Holes

SECURE FURNACE

WITH 2 FASTENERS AT FRONT

CORNER HOLES

Figure 14. “A” & “B” Cabinet Furnaces

Figure 12. Narrow Ducts

Narrow

Duct

Narrow

Duct

Duct connector tabs

Staples or sheet metal screws

Duct

Flap

Narrow

Duct

Connector

Sheet metal

screws

Figure 9. Floor Cavity

“X”

FLOOR OPENING

FLOO

CAVITY

SUPPLY AIR DUCT

FUEL LINE HOLES

MTG. PLATE TABS

SLIDE FURNACE

BACK AGAINST

MTG. PLATE

SECURE FURNACE

WITH 2 FASTENERS

AT FRONT CORNER HOLES

SUPPLY

AIR DUCT

Figure 15. “A” Cabinet Furnace on Coil Cabinet

NOTE: The depth of the ﬂoor cavity shown as “X” in

Figure 9 (page 8) will determine the correct duct

connector.

5. Determine which duct connector to use from Table 3,

(page 8).

6. Measure and drill gas hole and cut out for cooling coil

(if applicable). See Figure 6 or Figure 7.

Standard Duct Connector Installation

The standard duct connector is designed for use on

ducts 12” in width. Ducts narrower than 12” may not

allow sufﬁcient clearances for this type of installation. See

Alternate Attachment Method section below.

1. Center the duct connector in the ﬂoor opening with

bottom tabs resting on top of the supply air duct.

2. Mark the cut-out area on the supply air duct by tracing

around the connector tabs of the duct connector. See

Figure 8 (page 7).

3. Remove the duct connector and cut out the marked

area of the supply air duct 1/4” larger the actual cutout

drawn.

4. Install the duct connector back in the ﬂoor opening with

the bottom tabs extending into the supply air duct.

5. Install the mounting plate under the back side of the

duct connector as shown in Figure 8. Align the screw

holes in both components.

6. Secure the duct connector and the mounting plate to

the wood ﬂoor with appropriate size screws.

7. Bend the connector tabs on the bottom of the duct

connector upwards and as tight as possible against

the supply air duct.

8. Bend both tabs up 90° on the mounting plate. See

Figure 10 (page 8).

9. Seal all connections with industrial grade sealing tape

or liquid sealant.

NOTE: Requirements for sealing ductwork vary

from region to region. Consult with local codes for

requirements speciﬁc to your area.

Alternate Attachment Method

The standard duct connector is designed for use on ducts

12” in width. However if there is insufﬁcient clearance to

bend the duct connector tabs, this alternate attachment

method may be used.

1. Score and cut the top of the supply air duct as indicated

in Option 1 or Option 2. See Figure 11 (page 8).

NOTE: If Option 1 is selected, cut out the metal from

the shaded area.

2. Fold the two ﬂaps (Options 1 or 2) up to form the opening

for the duct connector.

3. Install the duct connector with the bottom tabs extending

into the supply air duct.

4. Bend the tabs on the bottom of the duct connector

upwards and as tight as possible against the supply

air duct. See Figure 12 (page 8).

5. Form the ﬂaps (Options 1 or 2) up against the duct

connector as tight as possible.

6. Secure the duct connector ﬂaps to the supply air duct

with staples (3 minimum) or if a 2x block/joist is not

provided, use sheet metal screws (2 minimum).

NOTE: The duct connector tabs may be attached to

the air duct with sheet metal screws or other suitable

fasteners as long as the duct connector and the air duct

are securely attached.

7. Seal all connections with industrial grade sealing tape

or liquid sealant.

NOTE: Requirements for sealing ductwork vary

from region to region. Consult with local codes for

requirements speciﬁc to your area.

Round Duct Connector Installation

1. Apply a bead of caulking, mastic, or other approved

sealant around bottom side of connector.

2. Install and center the duct connector in the ﬂoor opening.

3. Install the mounting plate under the back side of the

duct connector. See Figure 13. NOTE: Align the screw

holes in both components.

4. Secure the duct connector and the mounting plate to

the wood ﬂoor with appropriate size screws.

5. Connect the round supply duct to the underside of the

duct connector and secure them with ﬁeld supplied

sheet metal screws.

6. Seal all connections with industrial grade sealing tape

or liquid sealant.

NOTE: Requirements for sealing ductwork vary

from region to region. Consult with local codes for

requirements speciﬁc to your area.

Installing the Furnace

Sides and back of the furnace may be enclosed by wall

framing such as in a closet or alcove. The dimensions

of the room or alcove must be able to accommodate the

overall size of the furnace shown in Figure 4 (page 5)

and the installation clearances outlined on page 4. The

furnace shall be appropriately connected to the supply

distribution system as shown in Figure 14 (page 8) &

Figure 15 (page 8).

1. Remove furnace outer door(s) and bottom fuel line

knockout.

2. Place furnace onto duct connector and center with ﬂoor

opening.

3. Slide onto mounting plate. (Bottom rear slots on furnace

should engage with mounting plate tabs.)

4. Secure front with one (1) fastener at each corner. See

Figure 14 & Figure 15.

NOTE: Additional fasteners may be used at rear, sides

or through door frame, as desired, to secure furnace to

closet or alcove framing.

Figure 16. Ceiling Cavity Depth

ROOF JACK

CROWN

SLANT DECK

FLASHING

PITCHED

ROOF

CEILING

CAVITY

Roof

Opening

"X" (SEE TABLE 5)

Flue Pipe

Combustion Air Pipe

56"

76"

Furnace

“A”

“B”

SLANT DECK

FLASHING

PITCHED

ROOF

CEILING

ROOF

OPENING

"X" (SEE TABLE 5)

CEILING

CAVITY

CEILING

OPENING

ROOF JACK

CROWN

Figure 17. Example of Flat Jack with Flashing

5/12 ROOF SLOPE

SLANT DECK

/12

ROOF JACK WITH

FLASHING

/12 SLANT

Figure 18. Example of 2½ / 12 Slant Jack

with Flashing

ROOF JACK INSTALLATION

Required ceiling and roof cut-out openings must be

carefully located to avoid misalignment of the furnace

and Roof Jack. NOTE: Install only roof jack assemblies

listed in Table 4, (page 11) on this heating appliance.

Roof Jack Selection

1. Determine depth of ceiling cavity from center of roof

opening to center of ceiling opening noted as “Dimension

A” in Figure 16 (page 10).

2. Determine ceiling height and subtract height of furnace

noted as “Dimension B” in Figure 16 (page 10).

3. Add dimensions “A” & “B” (and X from Table 5, (page

11) if slant deck ﬂashing is used). The total length of

[A] + [B] + [X] must be within the minimum and maximum

range of the roof jack listed in Table 4.

Application Notes

• FAW, FAWT, SAW and SAWT Series Roof Jacks with a

5” diameter inner vent pipe may be used with all models

of M1 Series gas and M5 Series oil furnaces.

F = Flat Flashing: ﬂexes from 0/12 to 1/12 roof slope.

See Figure 17 (page 10).

S = Slant Flashing: 2.5/12 Slope ﬂexes from 1/12 to

4/12 roof slope, 4/12 ﬂexes from 3/12 to 5/12.

See Figure 18 (page 10).

• Stainless steel roof jacks are available.

• M1/M5 furnaces may be used with roof jack systems

and extension accessories as tall as 170” (except M1M

056 & M1B 066 models, which are limited to 120”).

An internal roof jack extension (p/n 901935 - 10”, p/n

903107 - 18”) can be used to increase roof jack height.

All connections inside the home must be made below

the ceiling.

• This furnace must never be connected to a chimney

ﬂue servicing a ﬁreplace or other appliance designed

to burn solid fuel.

• If the roof jack crown is covered or blocked with snow, the

furnace will not operate properly. If the home is located

in regions where snow accumulation exceeds 7” (HUD

snowload zones) use an external roof jack extension

(p/n 901937). A maximum of 2 extensions per roof jacks

can be used. Extensions are optional accessories and

may be purchased through your distributor.

Locating & Cutting Roof / Ceiling Openings

IMPORTANT NOTE:

Do not allow debris to fall into the furnace. This

could cause unsafe operation and void the furnace

warranty. Use the top cap that comes with the furnace

packaging (or alternate protector) to prevent debris

from falling into the furnace before the ﬁnal roof jack

connection is made.

NOTE: Refer to the installation instructions provided

with optional air conditioning packages when installing

furnaces with optional cooling coil cabinet or with optional

C* series indoor coils.

1. Locate center of Roof Jack opening, measure 13 1/2”

from the rear wall of closet or alcove along the center

line of furnace and ﬂoor opening. See Figure 19.

2. Cut ceiling and roof holes:

• Ceiling = 8 3/4” (222 mm) diameter

• Roof = 9 3/8” (238 mm) diameter

Installing The Roof Jack

1. Apply caulking compound on underside of roof ﬂashing

to form a continuous strip at least 3/8” wide around the

underside of the perimeter of the ﬂashing. For ﬂat roof,

see Figure 20 or see Figure 21 (page 12) if roof is

pitched.

2. Connect roof jack assembly to the furnace. Insert

telescoping roof jack assembly through the opening

cut on the roof.

3. Connect inner ﬂue pipe to vent collar of the furnace.

See Figure 22 (page 12).

4. Connect combustion air pipe to furnace collar with sheet

metal screw. See Figure 22.

NOTES:

• It is recommended that the connection of the combustion

air pipe to the furnace be made before the ﬂashing is

secured to the roof to maintain alignment of roof jack

and furnace connections.

• For replacement furnaces, be sure the inner ﬂue pipe

connects over the furnace vent collar. DO NOT use a

smaller diameter inner ﬂue pipe which could slide

inside the furnace vent collar and restrict the ﬂow

of furnace ﬂue products.

5. Attach roof ﬂashing. If necessary, shift roof ﬂashing

slightly in the roof opening so that assembly is in

alignment with furnace.

NOTE: If ﬂashing is mounted on 12 degree angle, it

may be necessary to adjust the angle to match the roof

pitch; (1/12 - 4/12 maximum).

6. Press down ﬁrmly on roof ﬂashing (over caulking) to

make the seal with roof water tight.

7. Secure ﬂashing with appropriate fasteners. NOTE: For

added protection against leaks, coat the ﬂashing plate

and fasteners with approved rooﬁng compound.

NOTE: Upper roof jack crown to be stored in a

prominent location inside manufactured home until

on-site installation.

Installing Transit-Mode Venting System

(Before Home is Moved to Site)

NOTE: For transit purposes, the transit kit (P/N 903838)

should be installed before home is moved to site.

1. Furnace must be installed in accordance to furnace

installation manual.

2. Select appropriate roof jack from Table 4, (page 11)

3. Roof jack (less upper roof jack crown), with weather

cap to be installed as described in Installing The Roof

Jack section.

4. Install the four warning tags (factory supplied) on these

items:

• Weather cap

• Fuel line connection point (Gas) or furnace burner (Oil)

• Furnace ﬂame observation door (Gas or Oil)

• Furnace wall thermostat

Table 4. Roof Jack Assemblies

SSAW

47 - 2

AW= ALL WEATHER

FLASHING

PITCH/12" RISE

0=FLAT

2=2.5/12

4=4/12

MIN. ADJ.

LENGTH

F = FLAT FLASHING

S = SLANT FLASHING

MAX. ADJ.

LENGTH

FLUE STEEL TYPE

A= ALUMINIZED

S=STAINLESS

MODEL NUMBER

APPROX. LENGTH

BELOW FLASHING

(F,S)AW1523-(0,2,4)(A,S) 15” - 23”

(F,S)AW2135-(0,2,4)(A,S) 21” - 35”

(F,S)AW2747-(0,2,4)(A,S) 27” - 47”

(F,S)AW3563-(0,2,4)(A,S) 35” - 63”

(F,S)AW5195-(0,2,4)(A,S) 51” - 95”

NOTE: Not all models are available. Check with your local distributor

for available models.

Figure 19. Cut-Out Dimensions for

Flue & Roof Jack

CEILING

CUT-OUT FOR

FLUE AND

ROOF JACK

24"

20"

13 1/2"

REAR WALL OF CLOSET OR ALCOVE

10"

FURNACE

OUTER

DOOR

FURNACE OUTLINE

Table 5. Slant Deck Flashings

ROOF JACK

SERIES

IF ROOF

PITCH IS:

SLANT DECK

FLASHING

NUMBER

“X”

“F Series

2” in 12” 903893 (2.5/12) 2-1/8”

2-1/2” in 12” 903893 (2.5/12) 2-1/2”

3” in 12” 903894 (3/12) 2-7/8”

3-1/2” in 12” 903894 (3/12) 3-1/4”

4” in 12” 903895 (4/12) 3-5/8”

“S” Series

(2.5 / 12 Pitch only)

4-1/2” in 12” 903895 (2.5/12) 2-1/8”

5” in 12” 903895 (2.5/12) 2-1/2”

5-1/2” in 12” 903894 (3/12) 2-7/8”

6” in 12” 903894 (3/12) 3-1/4”

6-1/2” in 12” 903895 (4/12) 3-5/8”

Optional deck ﬂashings for ﬂat and 2.5/12 pitch roof jacks.

4/12 pitch roof jacks not applicable.

Removing the Transit-Mode Venting System

(After home is moved to site)

WARNING:

Failure to properly secure the ﬂue pipe to

the furnace may result in ﬁre, explosion or

asphyxiation when operating the furnace.

1. Transit-mode weather cap to be removed and upper

roof jack crown installed. Do not discard the screws.

See Figure 23.

2. Place upper roof jack (crown) on the ﬂue pipe assembly.

NOTE: Make sure inside ﬂue pipe attaches over inner

ﬂue pipe and outer Roof Jack pipe ﬁts over outer pipe.

3. Secure in place using three sheet metal screws (#10

x 1/2”) removed in step 1. Do not use the same holes

which secured the rain cap in place.

4. Remove and discard all 4 venting system warning tags.

Figure 20. Flat Roof

Secure roof jack with

appropriate fasteners

after connecting to

furnace

Caulk under roof

flashing to prevent

water leakage

Roof

Ceiling

Optional 2-piece ceiling

ring #902521

Upper Roof Jack Section

Secure lower roof

jack section with

no. 10 S.M. screws

Caulk under roof

ashing to prevent

water leakage

Optional Slant

Deck Flashing

Secure ashing

with appropriate

fasteners

Ceiling

Figure 21. Pitched Roof

CONNECT OUTER

FLUE SHIELD

INNER FLUE PIPE

VENT COLLAR

MOUNTING

FLANGE

Figure 22. Combustion Air Pipe Connection

SCREWS

COMPLETED

ASSEMBLY

TO FURNACE

UPPER ROOF

JACK (CROWN)

INNER FLUE PIPE

FLUE ASSEMBLY

OUTER PIPE

FLASHING

WEATHER CAP

Figure 23. Roof Jack Crown

Figure 24. Control Panel (All Models)

On-Off

Switch

Blower

Plug

Power

Entry

On-Auto Switch

(Heating Models Only)

Thermostat Wires

Furnace

Control Box

To combustion

Blower or Flame

Roll-out Switch

To Gas Valve

or Burner

ELECTRICAL INFORMATION

WARNING:

ELECTRICAL SHOCK, FIRE OR

EXPLOSION HAZARD

Failure to follow safety warnings exactly could

result in serious injury or property damage.

Improper servicing could result in dangerous

operation, serious injury, death or property

damage.

• Before servicing, disconnect all electrical

power to furnace.

• When servicing controls, label all wires prior

to disconnecting. Reconnect wires correctly.

• Verify proper operation after servicing.

Line Voltage Wiring

WARNING:

To avoid electric shock, personal injury, or death,

turn off the electric power at the disconnect or the

main service panel before making any electrical

connections.

• Electrical connections must be in compliance with all

applicable local codes with the current revision of the

National Electric Code (ANSI/NFPA 70).

• For Canadian installations the electrical connections

and grounding shall comply with the current Canadian

Electrical Code (CSA C22.1 and/or local codes).

It is recommended that 115VAC line voltage be supplied

to the furnace from a dedicated branch circuit containing

the correct fuse or circuit breaker for the furnace as listed

in Table 6, (page 14).

IMPORTANT NOTE:

Refer to the wiring diagram inside the control box

cover or Figure 35 (page 31) & Figure 36 (page 32)

for the wiring of your particular unit. Any other wiring

methods must be acceptable to authority having

jurisdiction.

CAUTION:

Label all wires prior to disconnection when

servicing controls. Wiring errors can cause

improper and dangerous operation. Verify proper

operation after servicing.

IMPORTANT NOTE:

Proper line voltage polarity must be maintained in

order for the control system to operate correctly.

Verify the incoming neutral line is connected to the

white wire and the incoming “hot” line is connected

to the black wire. The furnace will not operate unless

the polarity and ground are properly connected as

shown in Figure 25 (page 14).

For installation of A-size Cabinet furnaces, allow sufﬁcient

slack in the wiring if an optional cooling coil cabinet is

added at a later time. Use of copper conductors is

recommended.

Connecting Power Supply Wires

1. Remove the furnace control panel cover.

2. Route wires (115 VAC) through the strain relief on the

left side of the furnace control box. See Figure 24 (page

12).

3. Connect the hot wire to the black pigtail lead, and

the neutral wire to the white pigtail lead. Secure all

connections with suitable wire nuts.

4. Connect the ground wire to the grounding screw.

5. Reinstall the control panel cover and secure with the

original mounting screws.

Low Voltage Wiring

• The furnace is designed to be controlled by a 24 VAC

thermostat. The thermostat’s wiring must comply with

the current provisions of the NEC (ANSI/NFPA 70) and

with applicable local codes having jurisdiction.

• The thermostat must be installed according to the

instructions supplied by the thermostat manufacturer.

Low voltage connections (24 VAC) from the thermostat

are wired to the terminal strip on the integrated control

in the furnace.

• The thermostat should be mounted about 5 feet above

the ﬂoor on an inside wall. DO NOT install the thermostat

on an outside wall or any other location where its

operation may be adversely affected by radiant heat from

ﬁreplaces, sunlight, or lighting ﬁxtures, and convective

heat from warm air registers or electrical appliances.

Refer to the thermostat manufacturer’s instruction sheet

for detailed mounting information.

• The nominal anticipator setting is 0.4. Refer to the

thermostat literature for additional information.

• Five-conductor thermostat wire is recommended for 24

volt low-voltage circuit (2-wire is required for furnace

only; 5-wire for heating and optional cooling systems).

Refer to Table 6 for thermostat wire information.

Connecting Thermostat Wires

1. Insert 24 volt wires through the plastic grommet just

above the control panel.

2. Connect the thermostat wires to the furnace low voltage

pigtails (dependent on the installation application). See

Figure 25 (page 14)..

• For M1 models: RH from the furnace is not connected;

RC of the furnace connects to the thermostat.

• For M5 models: To connect an M5 to a thermostat

without an RH & RC connection, please refer to the

wiring diagram and the installation instructions

supplied in the kit [P/N 1018453]. Units installed with kit

[P/N 1018453] will not use the RH connection from the

furnace, RC on the furnace connects to the thermostat.

3. Connect low-voltage circuit to the wall thermostat.

4. A hole may be made in the furnace cabinet to ease

thermostat wiring. Make sure that the wiring is protected

from the sharp edge of the added hole.

Verifying Anticipator Setting

After the furnace is installed, check the thermostat

anticipator against the nominal setting of 0.4.

1. Connect the milliamp meter in series with one of the

gas valve’s low voltage terminals.

2. Energize the gas valve.

3. Read the value of the milliamps.

4. Adjust the heat anticipator of the thermostat to the

value on the milliamp meter. If the heat anticipator is

set too high, the furnace may delay turning on. If set too

low, the furnace may cycle frequently and not provide

comfort to the homeowner.

Grounding

WARNING:

To minimize personal injury, the furnace cabinet

must have an uninterrupted or unbroken electrical

ground. The controls used in this furnace require

an earth ground to operate properly. Acceptable

methods include electrical wire or conduit

approved for ground service. Do not use gas

piping as an electrical ground!

Figure 25. Thermostat Wiring

Table 6. Voltage Speciﬁcations & Thermostat Wire Gauge

FURNACE

MODEL

NUMBER-

FURNACE

INPUT

(BTUH)

CABINET

WIDTH

(IN.)

NOMINAL

ELECTRICAL

SUPPLY

MINIMUM

OPERATING

VOLTAGE

MAXIMUM

OPERATING

VOLTAGE

MAXIMUM

FURNACE

AMPERES

MAXIMUM

FUSE OR CIRCUIT

BREAKER AMPS*

MINIMUM

CIRCUIT

AMPACITY

MAXIMUM

OVERCURRENT

PROTECTION

M1MB 056 56,000 19 3/4 115-1-60 103 127 7.0 15 8.5 14.5

M1MB 070 70,000 19 3/4 115-1-60 103 127 7.0 15 8.5 14.5

M1MB 077 77,000 19 3/4 115-1-60 103 127 7.0 15 8.5 14.5

M1MB 090 90,000 19 3/4 115-1-60 103 127 7.0 15 8.5 14.5

M1BB 066 66,000 19 3/4 115-1-60 103 127 6.8 15 8.3 14.3

M1BB 086 86,000 19 3/4 115-1-60 103 127 6.8 15 8.3 14.3

M1MC 056 56,000 19 3/4 115-1-60 103 127 8.9 15 10.9 18.8

M1MC 070 70,000 19 3/4 115-1-60 103 127 8.9 15 10.9 18.8

M1MC 077 77,000 19 3/4 115-1-60 103 127 8.9 15 10.9 18.8

M1MC 090 90,000 19 3/4 115-1-60 103 127 8.9 15 10.9 18.8

M1BC 066 66,000 19 3/4 115-1-60 103 127 8.7 15 10.7 18.6

M1BC 086 86,000 19 3/4 115-1-60 103 127 8.7 15 10.7 18.6

NOTE: Minimum wire gauge and maximum fuse/circuit breaker amperage are based on MCA

and MOP

calculations. This furnace is approved

for installation with a 15 or 20 amp fuse/circuit breaker however wiring sizing must adhere to current version of the NEC and/or applicable local

codes depending upon the overcurrent protection.

* Time-delay fuses or circuit breakers are required.

THERMOSTAT WIRE GAUGE

RECOMMENDED THERMOSTAT WIRE LENGTH (TOTAL LENGTH)

2 - WIRE - HEATING 4 OR 5 WIRE - COOLING

24 55 ft. 25 ft.

22 90 ft. 45 ft.

20 140 ft. 70 ft.

18 225 ft. 110 ft.

Total wire length includes wire from furnace to the thermostat, from thermostat to outdoor unit, & from outdoor unit back to the furnace.

Red

White

Green

Yellow

Red

White

Green

Grey

Thermostat

M1 Furnace

To AC Contactor

Red

White

Green

Yellow

Red

White

Green

Grey

Thermostat

M5 Furnace

To AC Contactor

Red Red

Oil Burner

FUEL SUPPLY & PIPING

WARNING:

FIRE OR EXPLOSION HAZARD

• Failure to follow safety warnings exactly could

result in serious injury or property damage.

• Installation and service must be performed

by a qualiﬁed installer, service agency or the

gas supplier.

• Do not store or use gasoline or other

ﬂammable vapors and liquids in the vicinity

of this or any other appliance.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not

use any phone in your building.

• Leave the building immediately.

• Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s

instructions.

• If you cannot reach your gas supplier, call

the ﬁre department.

WARNING:

All piping must conform with local building codes,

or in the absence of local codes, with the most

recent edition of the National Fuel Gas Code ANSI

Z223.1 or (CAN/CSA B149.1). Failure to follow all

safety warnings could result in serious injury,

death or property damage.

This furnace may be installed with left, right, or bottom gas

entry. When connecting the gas supply, provide clearance

between the gas supply line and the entry hole in the

furnace casing to avoid unwanted noise and/or damage

to the furnace. Typical gas service hookup for this furnace

is shown in Figure 26 (page 16).

Table 13, (page 29) lists gas ﬂow capacities for standard

pipe sizes as a function of length in typical applications

based on nominal pressure drop in the line.

IMPORTANT NOTES:

• Some local regulations require the installation of a

manual main shut-off valve and ground joint union

external to the furnace. See Figure 26 (page 16).

The shut-off valve should be readily accessible for

service and/or emergency use. Consult the local

utility or gas supplier for additional requirements

regarding placement of the manual main gas shut-

off.

• Gas piping must never run in or through air ducts,

chimneys, gas vents, or elevator shafts.

• Compounds used on threaded joints of gas piping

must be resistant to the actions of -liqueﬁed

petroleum gases.

• The main gas valve and main power disconnect to

the furnace must be properly labeled by the installer

in case emergency shutdown is required.

• Flexible gas connectors are not recommended for

this furnace but may be used if allowed by local

jurisdiction. Only new ﬂexible connectors may be

used. DO NOT reuse old ﬂexible gas connectors.

• A drip leg is recommended for a vertical run to the

unit.

• All piping shall be black iron pipe. Internally tinned

copper tubing may be used for gas supply systems.

• Fuel line installations other than typical installations

shown in Figure 26 (page 16) & Figure 27 (page

17) must comply with the fuel piping provisions

stated in the Federal Manufactured Home Standard

(H.U.D. TITLE 24, PART 3280) and the National Fuel

Gas Code (ANSI-Z223.1/NFPA-54).

• Shut-off valve must be designed and listed for use

with liquid petroleum (L.P. gas).

• A 1/8” NPT plugged tappings for test gauge

connection are present on the gas valve. See Figure

28 (page 17) for locations.

NOTE: Optional fuel inlet lines are available for all gas

furnace models to permit the addition of a 1/2” F.P.T.

shut-off valve above the ﬂoor.

The gas supply to your home will either be Natural Gas

or L.P. Your furnace is factory equipped to operate on

Natural Gas. If your gas supply is L.P., you must contact

a qualiﬁed serviceman or gas supplier to convert the

furnace. Instructions for conversion to propane are shown

on page 17. Factory installed oriﬁce sizes are listed in

Table 10, (page 28).

For natural gas operation, the maximum inlet pressure

for the valve is 7” W.C and the minimum inlet pressure

is 4.5” W.C. Pressure is reduced to 3 1/2” W.C. by the

pressure regulator in the gas valve.

For LP gas, pressure to the gas valve must be more than

11” W.C. but not more than 13” W.C. Pressure is reduced

to 10” W.C. by the pressure regulator in the gas valve.

Leak Check

WARNING:

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly could

result in serious injury or property damage.

Never test for gas leaks with an open ﬂame. Use

a commercially available soap solution made

speciﬁcally for the detection of leaks to check

all connections. A ﬁre or explosion may result

causing property damage, personal injury or

loss of life.

1. Turn off all electric power to the appliance.

2. Remove the black plastic cap located above the blower.

Do not discard cap.

3. Drill a hole through the top of the blower compartment.

NOTE: Hole diameter should be same size as sampling

tube.

4. Insert sampling tube through the drilled hole and into

the heat exchanger.

5. After a complete check and adjustment of furnace

performance, seal the drilled hole with a screw larger

than the hole. NOTE: Seal the screw threads with silicon

sealant - rated at least 500° F.

6. Plug the outside hole with the plastic cap removed in

step 3.

High Altitude Conversion

WARNING:

The reduction of input rating necessary for high

altitude installation may only be accomplished

with factory supplied oriﬁces. Do not attempt to

drill out oriﬁces in the ﬁeld. Improperly drilled

orifices may cause fire, explosion, carbon

monoxide poisoning, personal injury or death.

High altitude conversion with this furnace depends on

the installation altitude and the heating value of the gas.

The installation of this furnace at altitudes above 2,000

feet must meet the requirements of the National Fuel Gas

Code or local jurisdiction. In Canada, the requirements for

high altitude are different and governed by CSA B149.1.

Always consult your local code authority.

This furnace is shipped from the factory with oriﬁces and

gas regulator settings for natural gas operation at sea

level altitudes. At 2000 feet, the NFGC requires that this

appliance be derated 4% for each 1000 feet of altitude. For

example, the input needs to be reduced 8% at 2,000 feet,

12% at 3,000 feet and etc. This deration is in reference to

the input rate and gas heating value at sea level.

To derate the furnace requires knowing the heating value of

the gas at the installation site. Heating values at particular

job sites vary for two reasons:

1. The chemical mixture of the gas varies from region to

region and is expressed as the “sea level heating value”.

2. The heating value varies by altitude. For this reason,

especially in high altitude areas, the local gas utility

speciﬁes the heating value at the residence’s gas meter

as the “local value”.

For added ﬂexibility, two tables have been provided for

natural gas installations with high or low heating values

at sea level. Table 15, (page 30) & Table 16, (page

30) contain the manifold pressure and oriﬁce sizes to

use at various altitudes. Table 15 (HIGH) is for natural

gas installations with a heating value of more than 1,000

Btu per cubic foot and Table 16 (LOW) is for less than

1,000 Btu per cubic foot. To determine which table to use:

1. Consult the local utility for the local heating value at

your installation site.

Floor

Control

Panel

On-Off-Fan

Switch

Alt. Fuel

Line Entry

Floor Cavity

Some codes may require installation of a manual main shut-off

valve and ground joint union external to the furnace. The shut-off

valve should be readily accessible for service and/or emergency

use. Consult the local utility or gas supplier for additional

requirements regarding placement of the manual main gas shut-off.

To Gas Supply

Figure 26. Typical Gas Piping

After the gas piping to the furnace is complete, all

connections must be tested for gas leaks. This includes all

ﬁttings, pipe connections at the main gas valve, emergency

shutoff valve, and ﬂexible gas connectors (if applicable).

The soap and water solution can be applied on each

joint or union using a small paintbrush. If any bubbling is

observed, the connection is not sealed adequately and

must be retightened. Repeat the tightening and soap

check process until bubbling ceases.

CAUTION:

When pressure testing gas supply lines at

pressures greater than 1/2 psig (14 inch W.C.), the

gas supply piping system must be disconnected

from the furnace to prevent damage to the gas

control valve. If the test pressure is less than or

equal to 1/2 psig (14 inch W.C.), close the manual

shut-off valve

Flue Gas Sampling

It may be necessary to take ﬂue gas sampling from oil

and gas furnaces (M5S and M1B Series Models) in order

to check the performance after furnace installation. A

ﬂue gas sample may be taken from the heat exchanger,

which is located behind the hole of the top-front of blower

compartment.

2. From Table 14, (page 30), ﬁnd your local heating

value as supplied by the utility company. Follow down

the column and stop at your altitude level.

3. If your sea level heating value is HIGH, use Table 15

or if it’s LOW, use Table 16. See Example.

After changing the oriﬁces, it is required that you measure

the gas input rate. This may be accomplished in the usual

way, by clocking the gas meter and using the local gas

heating value. See Verifying Input Rate (page 22).

IMPORTANT NOTE:

Observe the action of the burners to make sure there

is no yellowing, lifting or ﬂashback of the ﬂame.

LP Gas

Configuration

Black Cover

Red

Ring

Natural Gas

Configuration

Gas Control

Lever

Figure 27. Robertshaw Gas Valve

Figure 28. Honeywell Gas Valve

PRESSURE

REGULATOR

CAP

OTHER SIDE

OF CAP

OUTLET PRESSURE

TAP (1/8 NPT)

INLET PRESSURE

TAP (1/8 NPT)

Installation Example

Elevation: ...................................................5,000 feet

Type of Gas: ............................................ Natural Gas

Local Heating Value of Gas: ...............................750

Determine which natural gas table to use. From Table

14, (page 30), ﬁnd 750 and follow down the column,

stop at the 5,000 feet row. The heating value listed is

LOW. Table 16, (page 30) will be used to determine

oriﬁce size and verify manifold pressure.

Conversion to Propane (LP) Gas

WARNING:

This furnace was shipped from the factory

equipped to operate on natural gas. Conversion

to LP/propane gas must be performed by qualiﬁed

service personnel using factory supplied

conversion parts. Failure to use the proper

conversion kit can cause ﬁre, explosion, property

damage, carbon monoxide poisoning, personal

injury, or death.

WARNING:

Shut off the gas supply at the manual gas shutoff

valve, before disconnecting the electrical power.

A ﬁre or explosion may result causing property

damage, personal injury or loss of life. Failure to

follow the safety warnings exactly could result in

serious injury, death or property damage.

WARNING:

To avoid electric shock, personal injury, or death,

turn off the electric power at the disconnect or the

main service panel before making any electrical

connections.

This furnace can be converted from factory-equipped

natural gas to liquid propane gas. Conversion of this valve

requires replacement of the burner oriﬁce and ﬂipping the

regulator cap to the side marked LP. The oriﬁce required

for conversion is supplied with the furnace. See Figure 27.

For altitudes between 0 and 1,999 feet, use the factory

supplied LP oriﬁce as shown in Table 10, (page 28).

Altitudes between 2,000 and 10,000 feet require the oriﬁce

to be changed. Table 17, (page 30) lists the correct

oriﬁce size and manifold pressure at different altitudes.

Atmospheric & Direct Ignition Furnaces

1. Follow the instructions in “How to Shut Off Gas - Direct

Ignition” on page 21.

2. Disconnect the gas pipe union and the electrical wires

connected to the gas valve.

3. Remove the gas valve assembly:

a. Remove screw(s) from gas valve bracket. Gas valve

and spud may be removed. Oriﬁce is located at the

end of the spud (M1M Models)

b. Remove three (3) bolts from U-shaped manifold plate

and oriﬁce assembly (M1B Models).

5. Replace the main oriﬁce with the L.P. gas oriﬁce supplied

in the envelope located by the gas valve. Verify the

oriﬁce size matches the nameplate or Table 10, (page

28).

6. For Honeywell gas valves with the regulator converter:

a. Unscrew the pressure regulator cap and check for

the letters NAT or LP. See Figure 27 (page 17).

b. Invert the cap and tighten until snug.

7. For Robertshaw gas valves with the regulator converter:

a. Remove the black cover and unscrew the converter

located on top of the gas valve. See Figure 28 (page

17).

b. Invert the converter. For LP, the red ring will be located

at the bottom and the LP stamping on the converter

will appear right side up.

c. Screw converter back into the regulator, hand tight

plus 1/8 turn. Replace the black cover on the converter

top to protect the threads.

8. Reassemble the burner assembly into the furnace.

9. Reconnect the gas piping and electrical wires to the

gas valve.

10. Open the manual shut-off valve and follow the M1M

Operating Instructions on page 20

Measuring the Supply Gas Pressure

To obtain an accurate pressure reading, turn off all

gas appliances (i.e. Dryers, water heaters, stoves,

etc.) at their ON/OFF control or individual gas valves.

1. Remove the inlet pressure plug from the INLET side

of the gas valve with a 3/16 Allen wrench. See Figure

27 (page 17).

2. Install a 1/8 NPT ﬁtting, which is compatible with a

manometer or similar pressure gauge.

3. Connect the manometer or pressure gauge to the inlet

pressure tap.

4. Turn on all electrical power to the furnace.

5. Turn the main gas supply valve (on the outside of the

unit) to the ON position.

6. Start the furnace by adjusting the thermostat to it’s

highest setting. Allow the furnace to run for 10 minutes.

7. Check the incoming gas line pressure. Propane gas

furnaces must be between 11.0”-14.0” W.C. Natural

gas installations must be between 4.5”-10.0” W.C. If

the pressure is not between these speciﬁed ranges,

contact your local gas supplier for adjustment.

8. Adjust the thermostat to it’s lowest setting and allow

the unit to cycle off.

9. Turn the main gas supply valve (on the outside of the

unit) to the OFF position.

10. Turn off all electrical power to the furnace.

11. Disconnect the manometer or pressure gauge.

12. Remove the NPT ﬁtting and reinstall the inlet pressure

plug. NOTE: To prevent cross threading, hand tighten

the plug ﬁrst, then tighten with 3/16 Allen wrench.

Measuring the Manifold Pressure

The manifold pressure must be measured by installing a

pressure gauge (Manometer, Magnehelic Meter, etc.) to

the outlet end of the gas valve.

1. Remove the manifold pressure plug from the outlet side

of the gas valve with a 3/16 Allen wrench.See Figure

27 (page 17).

2. Install a 1/8 NPT ﬁtting, which is compatible with a

Manometer or similar pressure gauge.

3. Connect the manometer or pressure gauge to the pipe

thread ﬁtting.

4. Start the furnace by adjusting the thermostat 5 degrees

above room temperature. Allow the furnace to operate

for 3 minutes.

5. Measure the manifold pressure on the manometer or

pressure gauge. Compare the measured value to the

value in Table 15, (page 30), Table 16, (page 30),

or Table 17, (page 30).

6. Replace the cap so that the letters facing up represent

the type of gas being used for the furnace. See Figure

27 (page 17).

7. Adjust the thermostat to its lowest setting.

8. Turn off the main gas supply to the unit at the manual

shut-off valve, which is located outside of the unit.

9. Turn off all of the electrical power to the furnace.

10. Disconnect the manometer or pressure gauge.

11. Remove the 1/8 NPT ﬁtting and reinstall the manifold

pressure plug. NOTE: To prevent cross threading,

hand tighten the plug ﬁrst then tighten with 3/16 Allen

wrench.

Oil Tank & Piping Installation

The following procedures are recommended as good

practice. However, requirements of local codes and

ordinances, H.U.D. Manufactured Home and Safety

Standards or National Fire Protection Association must be

satisﬁed, where they apply, for an approved installation.

• Use a tank capacity suitable for the application with a

weatherproof, capped ﬁll opening and a shielded vent

to let in air as fuel is used.

• The inside of the tank must be clean before ﬁlling. All

water, rust, sediment, and debris must be ﬂushed out.

• A fuel or tank gauge is recommended for easy checking

of the fuel level. Check the gauge reading with a dipstick.

See Figure 29 (page 19).

• Locate the storage tank conveniently near the home.

If the fuel tank is installed above ground, the tank may

rest 3 to 4 inches off the ground. Fuel tanks may also

be buried if properly coated to resist corrosion. The

vertical dimension from the bottom of the fuel tank to

the fuel pump must not exceed 10 feet.

• Keep the tank ﬁlled, especially in the summer to reduce

the accumulation of condensation.

One-Line System

The One-Line System is highly recommended where

vertical lift, from bottom of tank to pump, is less than 8

feet. See Figure 29 (page 19). A single line hookup

has the advantage of lower cost and quieter operation.

Two-Line System

If a Two-Line system is used or if oil is taken from the

bottom of the tank, a ﬁlter is recommended. A Two-Line

system should only be used if vertical lift exceeds 8 feet.

1. Install the oil feed line as outlined in steps 1 - 6 below.

2. Install the oil pump bypass plug in the bottom return

port.

3. Route the return line up through the furnace base to

the return port of the pump. Route the other end of the

line to the tank, using 3/8” O.D. copper tubing or 1/4”

pipe with the ends capped.

4. Insert the return line through the second opening in the

duplex bushing. If the bottom of the tank is lower than

the pump intake, the tube should be inserted three or

four inches from the tank bottom. If the bottom of the

tank is higher than the pump intake, the return line

should extend not more than 8” inside the tank.

Fuel line Hook-Up

1. Use a 3/8” O.D. copper tubing for the fuel line.

NOTE: Cap the end with tape to keep out dirt while the

line is being routed.

2. Install duplex bushing for two 3/8” lines in the top ﬁtting

of the tank. See Figure 29.

3. Insert one end of the tubing through the duplex bushing

until it is three to ﬁve inches from the bottom drain.

Tighten the bushing.

4. Route the line where it will not incur any damage. Make

bends gradual and avoid kinks which might restrict oil

ﬂow.

5. Open the furnace door and connect the oil line to the

intake port on the pump. Tighten other port plugs on

the pump. NOTE: Verify the oil line is airtight! Air leaks

can cause the pump to lose prime and will create other

problems such as nozzle failure, odors, rumbling noise,

and false safety shutdown.

6. Insert the short length of the copper tube level with the

bottom of the duplex bushing. Form the tube into an

inverted “U” to serve as a vent.

Fuel Line Bleeding

To eliminate problems caused by air in the oil line, all

connections in the oil supply line and all plugs, nuts,

and ﬁttings on the pump must be airtight. NOTE: This

includes the nut that covers the pressure adjustment. It

is important that the hook-up be done carefully and with

a good ﬂaring tool.

Prepare the burner for priming by attaching a clear plastic

hose over the bleed port ﬁtting and fully opening the pump

bleed port. Use a suitable container to collect purged oil.

To ensure continuous operation, use a wire to jump

terminals T-T (or F-F) on the primary control while burner

is running.

Priming furnaces equipped with Honeywell

R7184 primary control:

1. While the ignition is on, press for 1/2 second (or less),

and release the reset button. The lockout time will be

extended to 4 minutes.

2. If prime is not established within the 4 minutes, the

control will lock out. Press the reset button to reset the

control.

3. Repeat steps 1 & 2 (if needed) until the oil pump is fully

primed.

Priming furnaces equipped with Beckett 7505

primary control

1. After the burner starts, press and hold the reset button

until the yellow LED turns on (15 seconds). This indicates

that the button has been held long enough.

2. Release the reset button. The yellow LED will turn off

and the burner will start up again.

3. At burner start up, click the reset button while the igniter

is still on. This transitions the control to a dedicated pump

prime mode, during which the motor, igniter and valve

are powered for 4 minutes. The yellow LED will be on.

NOTE: If prime is not established during the four minute

pump prime mode, repeat step 3 until the oil pump is

fully primed.

4. When oil ﬂow is clear and free of air bubbles, close

air-bleed valve and tighten. NOTE: Air bleed out time

will varies depending on length of oil line, number of

bends, etc.

Figure 29. Typical Oil Piping for Above Ground (Single-Line) Supply

Top of Tank

8 ft.

Shut-off

Valve

Optional

Fuel

Filter

Alternate

Fuel Line

Entry

Control

Panel

Oil

Furnace

On-Off-Fan

Switch

Floor Cavity

Oil-Gun

Burner

Floor

Flue Gas

Sampling

Hole

Drain

End of Oil Supply Line

3" to 5" Above Bottom Drain

Guide

Pipe

Gauge

Vent with cap

2" Duplex

Bushing

2" Fill

3/8" Oil Supply Line

NOTE: Additional venting may be

required if tank is filled rapidly.

4 GPH 100-150 PSI 3450 RPM

3 GPH 150-200 PSI 3450 RPM

VALVE ON DELAY

NO. 2 & LIGHTER FUEL

USE ONLY WITH

INLET

BY-PASS

Exclusively for Beckett

Made by Suntec

INLET

NO. 2 FUEL

A2EA-6520

Becket

Nozzle Port

3/16 Flare Fitting

Bypass Solenoid Valve

Cordset

Inlet Port

1/4 NPTF

Bleed & Gauge Port

Pressure

Adjustment

Screw

Inlet Port

1/4 NPTF

Return Port - Install 1/6” Bypass Pipe

Plug for 2-pipe System Only.

(Use 5/32” Allen Wrench)

If fuel pump fails to lift oil, check for air

leaks and tighten all fuel fittings.

Reprime fuel pump by injecting fuel oil into

optional (top) return port. Replace return

port plug and repeat priming procedure.

Some codes may require installation of a manual main shut-off

valve and ground joint union external to the furnace. The shut-off

valve should be readily accessible for service and/or emergency

use. Consult the local utility or gas supplier for additional

requirements regarding placement of the manual main gas shut-off.

Fuel Oil Type

WARNING:

Do not use gasoline, crankcase oil, or any oil

containing gasline. Failure to keep supply of oil

clean by various procedures described above

may cause failure of certain components such as

the fuel pump gears, check valve, shaft seal, or

burner nozzle which may result in a burner ﬁre.

Do not use fuel oil heavier than Grade No. 2. In areas

where the oil supply is subject to low temperatures, Grade

No. 1 may be used.

STARTUP & ADJUSTMENTS

PLEASE READ ALL SAFETY INFORMATION

BEFORE LIGHTING THE FURNACE

WARNING:

FIRE OR EXPLOSION HAZARD

• Failure to follow safety warnings exactly could

result in serious injury or property damage.

• Installation and service must be performed

by a qualiﬁed installer, service agency or the

gas supplier.

• Do not store or use gasoline or other

ﬂammable vapors and liquids in the vicinity

of this or any other appliance.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not

use any phone in your building.

• Leave the building immediately.

• Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s

instructions.

• If you cannot reach your gas supplier, call

the ﬁre department.

WARNING:

Before placing the furnace in service, it must be

checked to ensure it is equipped for the type of gas

being used. The burner ﬂame must be observed

and adjusted if necessary. Failure to observe this

caution may result in unsafe operation, explosion

and/or ﬁre, or asphyxiation. See the Gas Supply

and Combustion Air sections.

• The ﬁrst operation of the furnace after any home

setup must be performed by a qualiﬁed service

technician.

• BEFORE STARTUP: Smell all around the furnace for

gas and next to the ﬂoor. Some gas is heavier than air

and may settle on the ﬂoor.

• M1B Units Only: Use only your hand to push in the gas

control lever. Never use tools. If the lever will not push

in by hand, don’t try to repair it. Force or attempted

repair may result in a ﬁre or explosion. Call a qualiﬁed

service technician.

• Do not use this furnace if any part has been under

water. Immediately call a service technician to inspect

the furnace and to replace any part of the gas valve or

control system which has been under water.

WARNING:

Close the hinged ﬁre door. If door is left open

or spring is broken it may allow products of

combustion into the living space by the furnace

blower, resulting in possible asphyxiation.

WARNING:

Should overheating occur, or the gas supply fails

to shut off, shut off the manual gas valve to the

furnace before shutting off the electrical supply.

M1M Operating Instructions

(Direct Ignition Furnaces)

Direct ignition furnaces do not have a pilot. Ignition is

accomplished by a hot surface ignitor. A circuit board

takes care of all timing functions. After lighting, the circuit

board uses the ignitor as a ﬂame sensor, shutting off gas

should the ﬂame go out. There are no external relays or

timing devices. Do not try to light this furnace by hand.

The circuit board is not ﬁeld serviceable.

1. Set the thermostat to the lowest setting.

2. Turn off all electric power to the appliance.

3. Remove the furnace door and turn off the gas valve:

• Honeywell: push in and turn the gas control knob

clockwise to OFF. See Figure 30.

• Robertshaw: push the gas control lever (Do not force!)

to the OFF position. See Figure 28, (page 17).

4. Wait ten (10) minutes to clear out any gas. If you smell

gas, STOP! and follow the Safety Information. If you

do not smell gas, proceed to step 5.

5. Set the thermostat MODE the ON position.

Figure 30. Direct Ignition Gas Valve - Honeywell

GAS CONTROL KNOB

La page charge ...

Maytag M1 Guide d'installation

Marque: Maytag

Modèle: M1

Taper: Guide d'installation

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Maytag M1 Installation guide

Maytag M1 Guide d'installation

Ce manuel convient également à

Maytag M1 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents