Columbia 769-04101 Manuel utilisateur

Catégorie
Souffleuses à neige
Taper
Manuel utilisateur

Ce manuel convient également à

Safety • Assembly • Operation • Adjustments • Maintenance • Troubleshooting • Parts Lists • Warranty
LES DISTRIBUTIONS RVI LIMITÉE, 2955, JEAN-BAPTISTE DESCHAMPS, LACHINE, QUEBEC H8T 1C5
PRINTED IN U.S.A.
IMPORTANT:
READ SAFETY RULES AND
INSTRUCTIONS CAREFULLY
BEFORE OPERATION
OPERATOR’S MANUAL
05/28/08
769-04101
28”, 30”, 33” & 45” Two-Stage Snow Throwers
2
Finding and Recording Model Number
Table of Contents
BEFORE YOU START ASSEMBLING
YOUR NEW EQUIPMENT,
please locate the model plate on the equipment and copy the
the model number and the serial number to the sample model
plate provided to the right. You can locate the model plate by
standing at the operating position and looking down at the
frame.
This Operator’s Manual is an important part of your new snow thrower. It will help you assemble,
prepare and maintain the unit for best performance. Please read and understand what it says.
Customer Support
1. If you have difficulty assembling this product or have any questions regarding the controls, operation or maintenance of this
unit, please call an authorized dealer.
Please have your unit’s model number and serial number ready when you call. See previous section to locate this
information.
2. The engine manufacturer is responsible for all engine-related issues with regards to performance, power-rating, specifica-
tions, warranty and service. Please refer to the engine manufacturer’s Owner’s/Operator’s Manual, packed separately with
your unit, for more information.
#/,5-")!#!.!$!
+)4#(%.%2/..'*
8888888888
88888888888
-ODEL.UMBER
.UM£RODEMODÞLE
3ERIAL.UMBER
.UM£RODES£RIE
Safety Symbols ................................................... 3
Safe Operation Practices ................................... 4
Setting Up Your Snow Thrower .......................... 6
Operating Your Snow Thrower ......................... 10
MakingAdjustments ......................................... 14
Maintaining Your Snow Thrower ...................... 16
Off-Season Storage .......................................... 20
Trouble Shooting .............................................. 21
Warranty ............................................................ 22
Illustrated Parts Lists ....................................... 24
3
Symbol Description
READ THE OPERATOR’S MANUAL(S)
Read, understand, and follow all instructions in the manual(s) before
attempting to assemble and operate
WARNING— ROTATING BLADES
Keep hands out of inlet and discharge openings while machine is running.
There are rotating blades inside
WARNING— ROTATING BLADES
Keep hands out of inlet and discharge openings while machine is running.
There are rotating blades inside
WARNING— ROTATING AUGER
Do not put hands or feet near rotating parts, in the auger/impeller housing
or chute assembly. Contact with the rotating parts can amputate hands and
feet.
WARNING—THROWN OBJECTS
This machine may pick up and throw and objects which can cause serious
personal injury.
WARNINGGASOLINE IS FLAMMABLE
Allow the engine to cool at least two minutes before refueling.
WARNING— CARBON MONOXIDE
Never run an engine indoors or in a poorly ventilated area. Engine exhaust
contains carbon monoxide, an odorless and deadly gas.
WARNING— ELECTRICAL SHOCK
Do not use the engine’s electric starter in the rain
1
Safety
Symbols
This page depicts and describes safety symbols that may appear on this product. Read, understand, and follow all
instructions on the machine before attempting to assemble and operate.
WARNING
This symbol points
out important safety
instructions which,
if not followed, could
endanger the per-
sonal safety and/or
property of yourself
and others. Read and
follow all instructions
in this manual before
attempting to operate
this machine. Failure
to comply with these
instructions may
result in personal
injury. When you see
this symbol, HEED
ITS WARNING!
Your Responsibility
Restrict the use
of this power machine
to persons who read,
understand
and follow the warnings
and instructions
in this manual
and on the machine.
4
2
Safe
Operation
Practices
Training
1. Read, understand, and follow all instructions on the
machine and in the manual(s) before attempting to
assemble and operate. Keep this manual in a safe place for
future and regular reference and for ordering replacement
parts.
2. Be familiar with all controls and their proper operation.
Know how to stop the machine and disengage them quickly.
3. Never allow children under 14 years old to operate this
machine. Children 14 years old and over should read and
understand the instructions and safe operation practices
in this manual and on the machine and be trained and
supervised by an adult.
4. Never allow adults to operate this machine without proper
instruction.
5. Thrown objects can cause serious personal injury. Plan
your snow-throwing pattern to avoid discharge of material
toward roads, bystanders and the like.
6. Keep bystanders, helpers, pets and children at least 75 feet
from the machine while it is in operation. Stop machine if
anyone enters the area.
7. Exercise caution to avoid slipping or falling, especially
when operating in reverse.
Preparation
Thoroughly inspect the area where the equipment is to be
used. Remove all doormats, newspapers, sleds, boards, wires
and other foreign objects, which could be tripped over or
thrown by the auger/impeller.
1. Always wear safety glasses or eye shields during
operation and while performing an adjustment or repair
to protect your eyes. Thrown objects which ricochet can
cause serious injury to the eyes.
2. Do not operate without wearing adequate winter outer gar-
ments. Do not wear jewelry, long scarves or other loose
clothing, which could become entangled in moving parts.
Wear footwear which will improve footing on slippery
surfaces.
3. Use a grounded three-wire extension cord and receptacle
for all units with electric start engines.
4. Adjust collector housing height to clear gravel or crushed
rock surfaces.
5. Disengage all control levers before starting the engine.
6. Never attempt to make any adjustments while engine is
running, except where specifically recommended in the
operator’s manual.
7. Let engine and machine adjust to outdoor temperature
before starting to clear snow.
Safe Handling of Gasoline
To avoid personal injury or property damage use extreme care
in handling gasoline. Gasoline is extremely flammable and the
vapors are explosive. Serious personal injury can occur when
gasoline is spilled on yourself or your clothes, which can ignite.
Wash your skin and change clothes immediately.
a. Use only an approved gasoline container.
b. Extinguish all cigarettes, cigars, pipes and other sources
of ignition.
c. Never fuel machine indoors.
d. Never remove gas cap or add fuel while the engine is hot
or running.
e. Allow engine to cool at least two minutes before refuel-
ing.
f. Never over fill fuel tank. Fill tank to no more than ½ inch
below bottom of filler neck to provide space for fuel
expansion.
g. Replace gasoline cap and tighten securely.
h. If gasoline is spilled, wipe it off the engine and equip-
ment. Move machine to another area. Wait 5 minutes
before starting the engine.
i. Never store the machine or fuel container inside where
there is an open flame, spark or pilot light (e.g. furnace,
water heater, space heater, clothes dryer etc.).
j. Allow machine to cool at least 5 minutes before storing
k. Never fill containers inside a vehicle or on a truck or
trailer bed with a plastic liner. Always place containers on
the ground away from your vehicle before filling.
l. If possible, remove gas-powered equipment from the
truck or trailer and refuel it on the ground. If this is not
possible, then refuel such equipment on a trailer with a
portable container, rather than from a gasoline dispenser
nozzle.
m. Keep the nozzle in contact with the rim of the fuel tank or
container opening at all times until fueling is complete.
Do not use a nozzle lock-open device.
WARNING: Engine Exhaust, some of its constituents, and certain vehicle compo-
nents contain or emit chemicals known to State of California to cause cancer and
birth defects or other reproductive harm.
WARNING
This symbol points
out important safety
instructions which,
if not followed, could
endanger the per-
sonal safety and/or
property of yourself
and others. Read and
follow all instructions
in this manual before
attempting to operate
this machine. Failure
to comply with these
instructions may
result in personal
injury. When you see
this symbol,
HEED
ITS WARNING!
Your Responsibility
Restrict the use
of this power machine
to persons who read,
understand
and follow the warnings
and instructions
in this manual
and on the machine.
DANGER: This machine was built to be operated according to the safe operation practices in this
manual. As with any type of power equipment, carelessness or error on the part of the operator can
result in serious injury. This machine is capable of amputating hands and feet and throwing objects.
Failure to observe the following safety instructions could result in serious injury or death.
5
Operation
1. Do not put hands or feet near rotating parts, in the auger/
impeller housing or chute assembly. Contact with the
rotating parts can amputate hands and feet.
2. The auger/impeller control lever is a safety device. Never
bypass its operation. Doing so makes the machine unsafe
and may cause personal injury.
3. The control levers must operate easily in both directions
and automatically return to the disengaged position when
released.
4. Never operate with a missing or damaged chute assembly.
Keep all safety devices in place and working.
5. Never run an engine indoors or in a poorly ventilated area.
Engine exhaust contains carbon monoxide, an odorless and
deadly gas.
6. Do not operate machine while under the influence of alcohol
or drugs.
7. Muffler and engine become hot and can cause a burn. Do
not touch.
8. Exercise extreme caution when operating on or crossing
gravel surfaces. Stay alert for hidden hazards or traffic.
9. Exercise caution when changing direction and while operat-
ing on slopes.
10. Plan your snow-throwing pattern to avoid discharge towards
windows, walls, cars etc. Thus, avoiding possible property
damage or personal injury caused by a ricochet.
11. Never direct discharge at children, bystanders and pets or
allow anyone in front of the machine.
12. Do not overload machine capacity by attempting to clear
snow at too fast of a rate.
13. Never operate this machine without good visibility or light.
Always be sure of your footing and keep a firm hold on the
handles. Walk, never run.
14. Disengage power to the auger/impeller when transporting or
not in use.
15. Never operate machine at high transport speeds on slippery
surfaces. Look down and behind and use care when
backing up.
16. If the machine should start to vibrate abnormally, stop the
engine, disconnect the spark plug wire and ground it against
the engine. Inspect thoroughly for damage. Repair any
damage before starting and operating.
17. Disengage all control levers and stop engine before you
leave the operating position (behind the handles). Wait
until the auger/impeller comes to a complete stop before
unclogging the chute assembly, making any adjustments, or
inspections.
18. Never put your hand in the discharge or collector openings.
Always use the clean-out tool provided to unclog the dis-
charge opening. Do not unclog chute assembly while engine
is running. Shut off engine and remain behind handles until
all moving parts have stopped before unclogging.
19. Use only attachments and accessories approved by the
manufacturer (e.g. wheel weights, tire chains, cabs etc.).
20. When starting engine, pull cord slowly until resistance is felt,
then pull rapidly. Rapid retraction of starter cord (kickback)
will pull hand and arm toward engine faster than you can let
go. Broken bones, fractures, bruises or sprains could result.
21. If situations occur which are not covered in this manual, use
care and good judgment. Call customer assistance for the
name of your nearest servicing dealer.
Maintenance & Storage
1. Never tamper with safety devices. Check their proper
operation regularly. Refer to the maintenance and adjust-
ment sections of this manual.
2. Before cleaning, repairing, or inspecting machine disengage
all control levers and stop the engine. Wait until the auger/
impeller come to a complete stop. Disconnect the spark plug
wire and ground against the engine to prevent unintended
starting.
3. Check bolts and screws for proper tightness at frequent
intervals to keep the machine in safe working condition.
Also, visually inspect machine for any damage.
4. Do not change the engine governor setting or over-speed
the engine. The governor controls the maximum safe
operating speed of the engine.
5. Snow thrower shave plates and skid shoes are subject to
wear and damage. For your safety protection, frequently
check all components and replace with original equipment
manufacturer’s (OEM) parts only. “Use of parts which do
not meet the original equipment specifications may lead to
improper performance and compromise safety!
6. Check controls periodically to verify they engage and
disengage properly and adjust, if necessary. Refer to the
adjustment section in this operator’s manual for instructions.
7. Maintain or replace safety and instruction labels, as neces-
sary.
8. Observe proper disposal laws and regulations for gas, oil,
etc. to protect the environment.
9. Prior to storing, run machine a few minutes to clear snow
from machine and prevent freeze up of auger/impeller.
10. Never store the machine or fuel container inside where
there is an open flame, spark or pilot light such as a water
heater, furnace, clothes dryer etc.
11. Always refer to the operator’s manual for proper instructions
on off-season storage.
12. Check fuel line, tank, cap, and fittings frequently for cracks
or leaks. Replace if necessary.
13. Do not crank engine with spark plug removed.
Do not modify engine
To avoid serious injury or death, do not modify engine in any
way. Tampering with the governor setting can lead to a runaway
engine and cause it to operate at unsafe speeds. Never tamper
with factory setting of engine governor.
Notice regarding Emissions
Engines which are certified to comply with California and federal
EPA emission regulations for SORE (Small Off Road Equipment)
are certified to operate on regular unleaded gasoline, and may
include the following emission control systems: Engine Modifica-
tion (EM) Oxidizing Catalyst (OC), Secondary Air Injection (SAI)
and Three Way Catalyst (TWC) if so equipped.
Average Useful Life
According to the Consumer Products Safety Commission
(CPSC) and the U.S. Environmental Protection Agency (EPA),
this product has an Average Useful Life of seven (7) years, or
60 hours of operation. At the end of the Average Useful Life,
have the machine inspected annually by an authorized service
dealer to ensure that all mechanical and safety systems are
working properly and not worn excessively. Failure to do so can
result in accidents, injuries or death.
2
Safe
Operation
Practices
WARNING
This symbol points
out important safety
instructions, which
if not followed, could
endanger the per-
sonal safety and/or
property of yourself
and others. Read and
follow all instructions
in this manual before
attempting to operate
this machine. Failure
to comply with these
instructions may
result in personal
injury. When you see
this symbol, HEED
IT’S WARNING!
Your Responsibility
Restrict the use
of this power machine
to persons who read,
understand
and follow the warnings
and instructions
in this manual
and on the machine.
05.08.08
6
3
Setting Up
Your Snow
Thrower
IMPORTANT: The snow thrower is shipped with oil and
WITHOUT GASOLINE. After assembly, refer to separate
engine manual for proper fuel and engine oil recom-
mendations.
Loose Parts
• Theaugersaresecuredtotheaugershaftwithshear
pins and bow tie cotter pins. If you hit a foreign object
or ice jam, the snow thrower is designed so that the
pins may shear. Replacement shear pins and cotter
pins are provided for your convenience. Store these
safely until needed.
Items Required For Assembly
Pair of pliers 7/16” Wrenches or adjustables
Fresh gasoline
Assembling Handle
• Look at the lower rear of the snow thrower frame to
be sure the spring (found at the end of each cable) is
attached to its actuator bracket.
• Removethelowerhandleknobs,washersand
carriage bolts from each side of the upper handle.
See Figure 3-2.
• Raise the upper handle assembly until it locks over
the lower handle. See Figure 3-1.
• Secure the upper handle and lower handle with the
handle knobs and carriage bolts previously removed.
• Tighten the handle knobs already in place on the
upper holes and secure the handles firmly.
Attaching Chute Crank
• Removethehairpinclipfromtheupperchutecrank
and slide the upper chute crank into the lower chute
crank. A pair of pliers may help in this job. See Figure
3-3.
a. Align the two holes on both chute cranks. See
Figure 3-3.
b. Secure with the hairpin clip removed earlier.
Figure 3-1
NOTE: This Operator’s
Manual covers several
models. Snowthrower
featrues vary by model.
Not all features refer-
enced in this manual
are applicable to all
snowthrower models.
NOTE: References to
right or left side of the
snow thrower are deter-
mined from behind the
unit in the operating
position.
NOTE: Replacement
auger shear pins and
cotter pins are provided
for your convenience.
Store these safely until
needed.
Figure 3-2
Figure 3-3
a
b
7
3
Prior to operating
your snow thrower,
refer to Auger Control
on page 9. Read and
follow all instructions
carefully and perform
all adjustments to
verify your unit is
operating safely and
properly.
Setting Up
Your Snow
Thrower
WARNING
Attaching the Chute Assembly
• Removelocknutsandscrewssecuringoneofthe
flange keepers to the chute assembly. See Figure 3-4.
• Loosenbutdonotremovethelocknutsandscrewson
the other two flange keepers.
• Slide chute assembly over chute opening, making
sure the flange keepers are beneath lip of chute
adapter. The notches should engage with the spiral
end of the chute crank. See Figure 3-5.
• Secureflangekeeper,locknutsandscrewspreviously
removed. Tighten all flange keepers and hardware
with two 7/16” wrenches. Do not over tighten.
NOTE: If necessary the chute crank support bracket can
be adjusted so the spiral on the chute crank fully engages
the teeth on the chute assembly. Refer to the Adjustment
Section.
Attaching the Shift Rod
• Aligntheupperandlowershiftrods,then slide the
shift rod connector down over the end of the lower
shift rod. Tap the connector until the lower rod is
completely through the connector. See Figure 3-6.
NOTE: If the connector is not properly assembled, the
shift rod will pivot and you will not be able to change
speeds or direction.
NOTE: If the full range of speeds (forward and reverse)
cannot be achieved, refer to the Adjustment Section.
• Normally the cable ties holding the steering cables
against the handle are loosely installed on each side
of the lower handle at the factory. Pull the cable ties
tight to secure. Cut the excess from the ends of cable
ties.
• Ifnotalreadyattached,slipthecablesthatrunfrom
the handle panel to the discharge chute into the cable
guide. See Figure 3-7.
Figure 3-4
Figure 3-5
Figure 3-6
Figure 3-7
8
3
Setting Up
Your Snow
Thrower
Drift Cutters (If Equipped)
Drift cutters should be used when operating the snow
thrower in heavy drift conditions.
• Onmodelssoequipped,driftcuttersandhardware
are assembled to the auger housing inverted.
• Removethecarriageboltsandwingnutssecuringthe
drift cutters to the housing.
• Repositiondriftcutterssotheyfaceforwardas
shown in Figure 3-9. Secure with hardware previously
removed, wingnuts should be fastened on the outside
of the housing as shown.
If your unit is not equipped with drift cutters, you may
contact Customer Support as instructed on page 2 for
information regarding price and availability.
Snowthrower Model Drift Cutter Kit:
All models OEM-390-679
Clean-Out Tool
The clean-out tool is mounted to the rear of the auger
housing and is designed to clear a clogged chute. See
Figure 3-10. Refer to the Operation section for more
detailed information regarding the chute clean-out tool.
NOTE: This item is fastened with a cable tie to the rear of
the auger housing at the factory. Cut the cable tie before
operating the snow thrower.
WARNING: Never use your hands to
clean snow and ice from the chute
assembly or auger housing.
Final Adjustments
Make these final adjustments before operating your snow
thrower for the first time. Failure to follow these instruc-
tions may cause damage to the snow thrower.
Wheel Drive Control & Shift Lever
Perform the following test to determine need for adjust-
ment:
• Movetheshiftleverintosixth(6)position.SeeFigure
3-14.
• Withthedrivecontrolreleased(seeFigure3-11A),
push the snow thrower forward, then pull it back. The
machine should move freely.
• Engagethedrivecontrolandattempttomovethe
machine both forward and back, resistance should be
felt.
• Movetheshiftleverintothefastreverse(R2)position
and repeat the previous two steps.
If you experienced resistance rolling the unit, either
when repositioning the shift lever from 6 to R2 or when
attempting to move the machine with the drive control
released, adjust the drive control immediately. To adjust,
proceed as follows:
WARNING
Never use your hands
to clean snow and
ice from the chute
assembly or auger
housing.
IMPORTANT
Under any circum-
stance do not exceed
manufacturer’s recom-
mended psi. Equal tire
pressure should be
maintained at all times.
Excessive pressure
when seating beads
may cause tire/rim
assembly to burst
with force sufficient to
cause serious injury.
Refer to sidewall of
tire for recommended
pressure.
Figure 3-10
Clean-Out
Tool
Figure 3-9
Alternator Lead
Lamp Wire
Alternator
Lead
NOTE:
Wheels are omitted from illustration for clarity.
Figure 3-8
Lamp Wiring
• Wrapthewirefromtheheadlampdowntheright
handle until the wire can be plugged into the alterna-
tor lead wire under the fuel tank. See Figure 3-8.
9
3
Setting Up
Your Snow
Thrower
WARNING
Never use your hands
to clean snow and
ice from the chute
assembly or auger
housing.
IMPORTANT
If the tire pressure is not
equal in both tires, the unit
may not travel in a straight
path and the shave plate
may wear unevenly.
A
B
Figure 3-11
• Repeataugercontroltesttoverifyforproper
adjustment. Repeat previous steps to adjust more, if
necessary.
Skid Shoes
Position the skid shoes based on surface conditions.
Adjust upward for hard-packed snow. Adjust downward
when operating on gravel or crushed rock surfaces. See
“Making Adjustment” Section.
Tire Pressure (Pneumatic Tires)
The tires are over-inflated for shipping purposes.
Check the tire pressure before operating the snow
thrower. Refer to the tire side wall for tire manufacturer’s
recommended psi and deflate (or inflate) the tires as
necessary.
• LoosentheNylocknutonthedrivecontrolcableand
unthread the cable one full turn. See Figure 3-13.
• Recheckadjustment.
• RetightentheNylocknuttosecurethecablewhen
correct adjustment is reached.
NOTE: For more details, refer to Drive Control Adjust-
ment in the Adjustment Section of this manual.
Auger Control
Check the adjustment of the auger control as follows:
• Whentheaugercontrolisreleasedandinthe
disengaged “up” position (see Figure 3-11B), the cable
should have very little slack, but should NOT be tight.
See Figure 3-12.
WARNING:Do not over-tighten the
cable. Over-tightening may prevent the
auger from disengaging and compro-
mise the safety of the snow thrower.
• Inawell-ventilatedarea,startthesnowthrowerengine
as instructed on page 12.
• Whilestandingintheoperatorsposition(behindthe
snow thrower) engage the auger.
• Allowtheaugertoremainengagedforapproximately
ten seconds before releasing the auger control.
Repeat this several times.
• Withtheaugercontrolleverinthedisengaged“up”
position, walk to the front of the machine.
• Confirmthattheaugerhascompletelystopped
rotating and shows no signs of motion.
IMPORTANT: If the auger shows any signs of rotating,
immediately return to the operator’s position and shut
off the engine. Wait for all moving parts to stop before
readjusting the auger control cable.
• Toreadjustthecontrolcable,unhookthespring(found
on the end of the auger cable) from the auger actuator
bracket. See Figure 3-12.
• Pushthecablecouplerthroughtheendofthespring
to expose the lock nut. See Figure 3-13.
• ThreadtheNylocknutoutward(downthecoupler)
three full turns to provide more slack in the cable and
reattach the spring to the bracket.
Figure 3-13
Figure 3-12
Drive
Auger
A
B
A - For models with steel panels.
B - For models with plastic panels.
10
4
Shift Lever
Two-Way Chute Control
Heated Handle Switch
(en option)†
Auger Control
Wheel Steering Control
Chute Directional Control
Headlights
Chute Assembly
Clean-Out Tool
Drive Control
Engine Controls
Recoil Starter
Handle
Choke
Control
Electric Starter
Outlet
(optional)
Electric Start
Button
(optional)
Primer
Safety
Key
Rocker
Switch
Oil Fill
Gas Cap
† If Equipped
Skid Shoe
Now that you have set up your snow thrower for opera-
tion, get acquainted with its controls and features. These
are described below and illustrated on this page. This
knowledge will allow you to use your new equipment to
its fullest potential.
NOTE: For detailed starting instructions and more
information on all engine controls, refer to the separate
engine manual packed with your unit.
Know Your Snow Thrower
Choke Control
The choke control is found on the top of the
engine and is activated by rotating the knob
counter clockwise. Activating the choke
control closes the choke plate on the carbure-
tor and aids in starting the engine.
Primer
Depressing the primer forces fuel directly into the engine’s
carburetor to aid in cold-weather starting.
Oil Fill
Engine oil level can be checked and oil added through the
oil fill.
Safety Key
The safety key must be pushed in place in order for the
engine to start. Pull the safety key out to prevent unauthor-
ized use of equipment.
Rocker Switch
The rocker switch is used to stop the engine. The switch
must be in the “ON” position in order to start the engine.
Figure 4-1
Operating
Your Snow
Thrower
WARNING
Read, understand,
and follow all instruc-
tions and warnings
on the machine and
in this manual before
operating.
Use extreme care
when handling
gasoline. Gasoline is
extremely flammable
and the vapors are
explosive. Never fuel
the machine indoors
or while the engine
is hot or running.
Extinguish cigarettes,
cigars, pipes and
other sources of
ignition.
6
1
2
F
3
4
5
R2
R1
R
Shift Lever
The shift lever is located in the center of
the handle panel and is used to determine
ground speed and direction of travel. It can
be moved into any of eight positions.
IMPORTANT: Always release drive control
before changing speeds.
Forward: The snow thrower has six
forward (F) speeds. Position one (1) is the
slowest and position six (6) is the fastest.
Reverse: The snow thrower has two
reverse (R) speedsR1 is the slower of
the two.
11
4
Operating
Your Snow
Thrower
WARNING
The operation of
any snow thrower
can result in foreign
objects being thrown
into the eyes, which
can damage your
eyes severely. Always
wear safety glasses
while operating the
snow thrower, or while
performing any adjust-
ments or repairs on it.
Be sure no one other
than the operator is
standing near the snow
thrower while starting
engine or operating
snow thrower. Never
run engine indoors or
in enclosed, poorly
ventilated areas. En-
gine exhaust contains
carbon monoxide, an
odorless and deadly
gas. Keep hands, feet,
hair and loose clothing
away from any moving
parts on engine and
snow thrower.
Auger Control
The auger control is located on the left handle. Squeeze
the auger control to engage the augers. Release to stop
the snow throwing action. The drive control must also be
released in order to stop auger.
Drive Control / Auger Control Lock
The drive control is located on the right handle. Squeeze
the drive control to engage the wheel drive. Release to
stop.
This same lever also locks the auger control so you
can operate the chute crank without interrupting the
snow throwing process. If the auger control is engaged
simultaneously with the drive control, the operator can
release the auger control (on the left handle) and the
augers will remain engaged. Release the drive control to
stop the augers and wheel drive (the auger control must
also be released).
IMPORTANT: NEVER reposition the shift lever (change
speeds or direction of travel) without first releasing the
drive control and bringing the snow thrower to a complete
stop. Doing so will result in premature wear to the snow
thrower’s drive system.
Heated Handles Switch (If Equipped)
This switch is located on the right side of the snow
thrower dash panel. To activate the heated handles,
toggle the switch to the “ON” position to generate heat
within the handle grips. Toggle the switch to the “OFF
position after using the snow thrower.
NOTE: The heated handles grips are a compliment to,
not a substitute for, proper cold weather outerwear for
the operator’s hands. It is recommended that the snow
thrower operator wear gloves/mittens to avoid extremities
of winter while operating this equipment.
!5'%2
#/.42/,
'/
$2)6%
#/.42/,
'/
Two-Way Chute Control™)
This two-way control lever is meant to
control the distance of snow discharge from
the chute. Tilt the lever forward or rearward
to adjust the distance snow will be thrown.
Chute Directional Control
The chute directional control is
located on left side of the snow
thrower.
To change the direction in which
snow is thrown, turn chute direc-
tional control as follows:
• Crankclockwisetodischargeto
the left.
• Crankcounterclockwisetodischargetotheright.
Wheel Steering Controls
The left and right wheel steering
controls are located on the underside
of the handles. Squeeze the right
control to turn right; squeeze the left
control to turn left.
NOTE: Operate the snow thrower in open areas until you
are familiar with these controls.
Chute Clean-Out Tool
WARNING: Never use your hands to
clear a clogged chute assembly. Shut
off engine and remain behind handles
until all moving parts have stopped
before unclogging.
The clean-out tool is conveniently fastened to the rear of
the auger housing with a mounting clip.
1. Release both the auger control and the drive/auger
control lock.
2. Stop the engine by pushing the rocker switch to the
“OFF” position, pull out the safety key.
3. Remove the clean-out tool from the mounting clip.
4. Use the shovel-shaped end of the clean-out tool to
remove any snow and ice in the chute assembly.
5. Re-fasten the clean-out tool to the mounting clip on
the rear of the auger housing and restart engine.
6. While standing in the operators position (behind the
snow thrower), engage the auger control for a few
seconds to clear any remaining snow or ice from the
chute assembly before continuing to clear snow.
Skid Shoes
Position the skid shoes based on surface conditions.
Adjust upward for hard-packed snow. Adjust downward
when operating on gravel or crushed rock surfaces. See
“Making Adjustment” Section.
Headlight
The headlight is on whenever the engine is running.
C L O C K W IS E T O
DISCHARGE LEFT
COUNTER CLOCKWISE
TO DISCHARGE RIGH
T
12
WARNING
4
Read, understand,
and follow all instruc-
tions and warnings
on the machine and
in this manual before
operating.
Use extreme care
when handling
gasoline. Gasoline is
extremely flammable
and the vapors are
explosive. Never fuel
the machine indoors
or while the engine
is hot or running.
Extinguish cigarettes,
cigars, pipes and
other sources of
ignition.
Gas & Oil Fill-Up
Service the engine with gasoline and oil as instructed in
the separate engine manual packed with your unit. Read
instructions carefully.
Starting The Engine
1. Make certain both the auger control and drive control
are in the disengaged (released) position.
2. Open fuel shut-off valve (If equipped) and make sure
the Rocker switch is in the On position (if equipped).
3. Push in the safety key.
4. Rotate choke control to FULL choke position
(for a cold engine start).
NOTE: If the engine is already warm, place choke
control in the OFF position instead of FULL.
5. Push the primer two times if temperature is above
15
o
F (-9
o
C), four times if temperature is below 15
o
F
(-9
o
C) for cold engine start, making sure to cover
vent hole in the center of the primer when pushing.
NOTE: DO NOT use primer to restart a warm engine
after a short shutdown.
Electric Starter (If Equipped)
1. Determine that your home’s wiring is a three-wire
grounded system. Ask a licensed electrician if you
are not certain.
WARNING: The optional electric
starter is equipped with a grounded
three-wire power cord and plug, and
is designed to operate on 120 volt AC
household current. It must be used
with a properly grounded three-prong
receptacle at all times to avoid the
possibility of electric shock. Follow all
instructions carefully prior to operat-
ing the electric starter.
If you have a grounded three-prong receptacle, proceed
as follows:
1. Plug the extension cord into the outlet located on the
engine’s surface. Plug the other end of extension
cord into a three-prong 120-volt, grounded, AC outlet
in a well-ventilated area.
2. Push starter button to start engine.
3. Once the engine starts, immediately release starter
button.
4. As the engine warms, slowly rotate the choke control
to the OFF position
. If the engine falters,
quickly rotate the choke control back to FULL and
then slowly into the OFF position again.
5. When disconnecting the extension cord, always
unplug the end at the three-prong wall outlet before
unplugging the opposite end from the snow thrower.
Recoil Starter
1. Grasp the recoil starter handle and slowly pull the rope
out. At the point where it becomes slightly harder to pull
the rope, slowly allow the rope to recoil.
2. Pull the starter handle with a firm, rapid stroke. Do not
release the handle and allow it to snap back. Keep a firm
hold on the starter handle and allow it to slowly recoil.
3. As the engine warms, slowly rotate the choke control to
the OFF position. If the engine falters, quickly rotate the
choke control back to the FULL position and then slowly
into the OFF position again.
NOTE: Allow the engine to warm up for a few minutes
after starting. The engine will not develop full power until it
reaches operating temperatures.
Stopping The Engine
Run engine for a few minutes before stopping to help dry off
any moisture on the engine.
• Pushtherockerswitchtothe“OFF”position.
• Pulloutthesafetykey.
• Closefuelshut-offvalve(Ifequipped).
• Wipeallsnowandmoisturefromtheareaaroundthe
engine as well as the area in and around the drive
control and auger control. Also, engage and release
both controls several times.
To Engage Drive
1. With the engine running near top speed, move
shift lever to one of six FORWARD positions or two
REVERSE positions. Select a speed appropriate for
the snow conditions that exist.
2. Squeeze drive control against the right handle and
the snow thrower will move. Release it and the drive
motion will stop.
To Engage Augers
1. To engage augers and start snow throwing, squeeze
the left hand auger control against the left handle.
Release to stop augers.
2. While the auger control is engaged, squeeze the drive
control to move, release to stop. Do not shift speeds
while the drive is engaged.
NOTE: The drive control lever also locks auger control
so you can turn the chute control without interrupting the
snow throwing process.
3. Release the auger control; the interlock mechanism
should keep the auger control engaged until the drive
control is released.
4. Release the drive control to stop both the augers and
the wheel drive. To stop the auger, both levers must be
released.
Operating
Your Snow
Thrower
13
WARNING
4
Operating
Your Snow
Thrower
NOTE: Use slower
speeds in higher
snow and/or until you
are familiar with the
snow thrower opera-
IMPORTANT
NEVER move the
shift lever without first
releasing the wheel
drive control. Doing so
will cause premature
wear on the drive
systems friction wheel.
The muffler, engine
and surrounding
areas become hot
and can cause a burn
150°F (65°C). Do not
touch.
Operating Tips
NOTE: Allow the engine to warm up for a few minutes.
The engine will not develop full power until it reaches
operating temperature.
WARNING: The temperature of the
muffler and the surrounding areas may
exceed 150° F (65° C). Avoid these
areas.
1. If possible, remove snow immediately after it falls.
2. Discharge snow downwind whenever possible.
3. Slightly overlap each previous path.
4. Set the skid shoes 1/4” below the shave plate for
normal usage. Adjust them upward for hard-packed
snow and downward when using on gravel or crushed
rock.
General Recommendations
1. Always observe safety rules when performing
any maintenance.
2. The warranty on this snow thrower does not cover
items that have been subjected to operator abuse
or negligence. To receive full value from warranty,
operator must maintain the snow thrower as
instructed here.
3. Some adjustments will have to be made periodically
to maintain your unit properly.
4. Periodically check all fasteners and make sure these
are tight.
14
5
Making
Adjustments
WARNING
Read, understand,
and follow all instruc-
tions and warnings
on the machine and
in this manual before
operating.
Never attempt to
make any adjust-
ments while the
engine is running,
except where speci-
fied in operator’s
manual.
Run the engine
completely dry of
gasoline before
tipping snowthrower.
Shift Rod
If the full range of speeds (forward and reverse) cannot
be achieved, refer to Figure 5-1 and adjust the shift rod
as follows:
1. Looking underneath the handle panel, note which
of the three holes in the shift lever the ferrule is
inserted into. Also note the direction of insertion.
Then remove the internal cotter pin and flat washer
from the ferrule and withdraw the ferrule from the
shift lever. See Figure 5-1.
2. Place shift lever in sixth (6) position or fastest
forward speed.
3. Push shift rod and shift arm assembly down sharply,
as far as it will go to put the drive into the fastest
forward position.
4. As necessary, rotate the ferrule up or down the shift
rod until the ferrule lines up with the hole from which
it was earlier removed. See Figure 5-1.
5. From the direction noted earlier, insert the ferrule
into the proper hole.
6. Reinstall the washer and the internal cotter pin.
Drive Control
WARNING: Run the engine com-
pletely dry of gasoline before tipping
snowthrower.
Refer to the Final Adjustment section of the Set-Up
instructions to adjust the drive control. To further check
the adjustment, proceed as follows:
1. Tip the snow thrower forward, allowing it to rest on
the auger housing.
2. Remove the frame cover underneath the snow
thrower by removing the self-tapping screws. See
Figure 5-2.
3. With the wheel drive control released, check if there
is clearance between friction wheel and drive plate in
all positions of the shift lever. See Figure 5-3.
4. With the drive control lever engaged, check if the
friction wheel solidly contacts the drive plate. See
Figure 5-3. If not, adjust as follows:
a. Loosen the jam nut on the drive cable and thread
the cable in or out as necessary.
b. Retighten the jam nut to secure the cable when
correct adjustment is reached.
5. Reassemble the frame cover.
Figure 5-1
Figure 5-2
Figure 5-3
Axle Supp.
Brkt.
Opening
Drive
Plate
Friction
Wheel
15
5
IMPORTANT: It is not
recommended that
you operate this snow
thrower on gravel as
loose gravel can be
easily picked up and
thrown by the auger
causing personal
injury or damage to
the snow thrower.
If for some reason,
you have to operate
the snow thrower on
gravel, keep the skid
shoe in the highest
position for maximum
clearance between the
ground and the shave
plate.
Making
Adjustments
Figure 5-4
Skid Shoes
The space between the shave plate and the ground can
be adjusted by raising or lowering the skid shoes.
For close snow removal, as when using on a smooth
concrete or asphalt driveway, place the skid shoes in the
low position. Use the middle or high position when the
area to be cleared is uneven. When operating on gravel,
always put skid shoes in the high position.
See Figure 5-4.
Adjust skid shoes as follows:
1. Loosen, but do not remove, the hex flange locknuts
which fasten the skid shoe to the auger housing.
2. Raise or lower the skid shoe to desired position.
3. Retighten the hex nuts loosened earlier.
NOTE: Make certain the bottom surface of skid shoe is
flat against the ground to avoid uneven wear.
4. Repeat on the other side of the snow thrower.
Auger Control
Refer to instructions on page 9 to adjust the auger
control. Make certain to check for correct adjustment as
instructed before operating the snow thrower.
Chute Assembly
The distance snow is thrown can be adjusted by adjusting
the angle of the chute assembly. Refer to page 9 for
instructions.
The remote chute control cables have been pre-adjusted
at the factory. Move the remote chute lever on the control
panel back and forward to adjust angle of the chute
assembly.
Chute Bracket Adjustment
If the spiral at the bottom of the chute directional control
is not fully engaging with the chute assembly, the chute
bracket can be adjusted. To do so:
1. Loosen the two nuts which secure the chute bracket
and reposition it slightly. See Figure 5-5.
2. Retighten the nuts.
Figure 5-5
16
6
Maintaining
Your Snow
Thrower
WARNING
Before lubricating,
repairing or
inspecting, disengage
all controls and stop
engine. Wait until all
moving parts have
come to a complete
stop. Remove the
safety key to prevent
unintended firing of
the engine.
IMPORTANT
Avoid oil spillage on
rubber friction wheel
and aluminum drive
plate.
Figure 6-1
Figure 6-2
Lubrication
Drive and Shifting Mechanism
At least once a season or after every 25 hours of opera-
tion, remove rear cover. Lubricate any chains, sprockets,
gears, bearings, shafts, and the shifting mechanism at
least once a season. Use engine oil or a spray lubricant.
Refer to Figure 6-1.
IMPORTANT: Keep all grease and oil off the rubber
friction wheel and drive plate.
Wheels
At least once a season, remove wheels. Clean and coat
the axles with a multipurpose automotive grease before
reinstalling wheels.
Auger Shaft
At least once a season, remove the shear pins on auger
shaft. Spray lubricant inside shaft, around the spacers.
Also lubricate the flange bearings found at either end of
the shaft. See Figure 6-2.
Augers
• Theaugersaresecuredtothespiralshaftwithshear
pins and cotter pins. If the auger should strike a
foreign object or ice jam, the snow thrower is designed
so that the pins may shear. See Figure 6-2.
• Iftheaugerswillnotturn,checktoseeifthepinshave
sheared. Replacement shear pins have been provided
with the snow thrower. When replacing pins, spray an
oil lubricant into shaft before inserting new pins.
Shave Plate and Skid Shoes
The shave plate and skid shoes on the bottom of the
snow thrower are subject to wear. They should be
checked periodically and replaced when necessary.
To remove skid shoes:
1. Remove the carriage bolts (and washers if
equipped)and hex flange nuts which secure the skid
shoes to the snow thrower.
2. Reassemble new skid shoes with previously removed
hardware. Refer to Figure 6-3.
To remove shave plate:
1. Remove the carriage bolts and hex nuts which attach
it and the skid shoes to the snow thrower housing.
2. Reassemble new shave plate, making sure heads of
carriage bolts are to the inside of housing. Tighten
securely.
Replacing Belts
To remove and replace either the auger belt or the drive
belt, follow the steps below and then proceed to the
specific steps listed under respective sub-headings.
1. Disconnect the chute crank assembly at the discharge
chute end by removing the hairpin clip and the flat
washer. See Figure 6-8.
Figure 6-3
Shear Pin
Vent Plug
Grease
Fitting (optional)
Bearing
SpacersCotter Pin
Auger Shaft
Engine
Refer to the separate engine manual packed with your
unit for all engine maintenance and lubrication instruc-
tions.
Friction
Wheel
Drive
Plate
Gear
(Hex)
Shaft
17
6
Maintaining
Your Snow
Thrower
2. Remove the plastic belt cover, located near the
engine, by removing the three self-tapping screws that
secure it. See Figure 6-4.
3. a. Loosen the bolt shown in Figure 24 securing the
belt keeper bracket and remove the other bolt.
b. Push the belt keeper and bracket up off the engine
pulley. See Figure 6-54.
Auger Belt
4. Remove the clip and flat washer from the ferrule in
order to disconnect the auger idler rod from the brake
bracket assembly. See Figure 6-6.
5. Slip the auger belt (the front belt) off the engine pulley.
6. Pull the brake bracket assembly towards the cable
guide roller and unhook the auger cable “Z” fitting.
See Figure 6-7.
7. From both sides of the the frame assembly, use a 1/2
wrench to remove the three hex tap screws securing
the frame to the auger housing assembly. See Figure
6-8.
NOTE: Do not remove the lower hex flange lock nut
on each side.
IMPORTANT
NEVER replace the
auger shear pins with
standard pins. Any
damage to the auger
gearbox or other com-
ponents, as a result of
doing so, will NOT be
covered by your snow
thrower’s warranty.
Check the condition
of both auger belt and
drive belt every 25
hours of snow thrower
operation. Replace if
either shows signs of
wear and tear.
Specifications are
subject to change
without notification or
obligation. Images may
not reflect your exact
model and are for refer-
ence purposes only.
Figure 6-5
Figure 6-6
Figure 6-7
Figure 6-4
Loosen
Remove
Figure 6-8
18
6
Maintaining
Your Snow
Thrower
WARNING
Before lubricating,
repairing or
inspecting, disengage
all controls and stop
engine. Wait until all
moving parts have
come to a complete
stop. Remove the
safety key to prevent
unintended firing of
the engine.
8. Place a block of wood underneath the auger housing
as shown in Figure 6-9 and separate auger housing
from the frame by tilting the housing forward and
pulling up the handles.
9. Block the impeller with a piece of wood to prevent if
from spinning and use a 1/2” wrench to remove the
hex screw and washer from the center of the pulley on
the auger housing. See Figure 6-10.
10. Lift the brake bracket assembly out of the pulley
groove and slide the pulley assembly off the posts of
the auger pulley adapter to remove the old belt. Refer
to Figure 6-10.
NOTE: The pulley adapter may slide off the auger input
shaft when removing the pulley. Use extra caution to
ensure the adapter does fall and/or get damaged when
removing the pulley.
11. Place the new auger belt in the V-groove of the
auger pulley and place the pulley w/belt inside the
belt keepers.
12. Turn the pulley as necessary to align its three slots
approximately with the posts of the pulley adapter,
then move the brake bracket assembly away from
the input shaft. While aligning the pulley slots and
adapter posts, push the auger pulley fully onto the
adapter. Refer to Figure 6-10.
NOTE: If the pulley adapter was removed with the
pulley, align the splines of the pulley adapter and auger
input shaft, and push the pulley and adapter onto the
input shaft. Refer to Figure 6-10.
13. Slide the washer onto the hex screw removed earlier
and apply Loctite 262 to the threads of the hex screw.
14. Insert the hex screw through the pulley assembly
and into the threads of the input shaft. Torque the
hex screw to 250-325 in./lbs. to secure the auger
pulley assembly on the input shaft.
If also replacing the drive belt, proceed to the “Drive Belt”
instruction. If not, reassemble by performing the previous
steps in the opposite order and manner of removal.
NOTE: Make sure to remove the piece of wood blocking
the impeller.
Proper Adjustment: With the auger clutch lever in the
disengaged position, the top surface of the new belt
should be even with the outside diameter of the pulley.
1. To adjust, disconnect ferrule from brake bracket
assembly and thread ferrule in (towards idler) to
increase tension on belt, and out to decrease tension.
See Figure 6-6.
NOTE: The brake puck must always be firmly seated in
the pulley groove when auger control is disengaged.
IMPORTANT: Repeat the “Auger Drive Control Test” from
the Assembly section before operating snow thrower.
Figure 6-9
Figure 6-11
Figure 6-10
IMPORTANT
Refer to the Final
Adjustment section of
the Set-Up instructions
after replacing drive
and auger belts.
A
C
B
Pulley Slot
Adapter Post
Drive Belt
1. If not already done, remove auger belt as previous
instructed.
a. Pull the idler pulley away from the backside of the
drive belt to relieve the tension.
b. Slide the drive belt off the idler pulley. See Figure
6-11. Carefully release the idler pulley.
2. Remove the belt from the bottom drive pulley.
3. Remove the belt from the engine pulley.
1b
2
1a
3
19
6
Maintaining
Your Snow
Thrower
WARNING
The rubber on the fric-
tion wheel is subject
to wear and should be
checked periodically.
Replace the friction
wheel rubber if any
signs of wear or
cracking are found.
remove the hex bolts and cupped washer and bearing
from left side of the frame. Refer to Figure 6-12.
• Holdingthefrictionwheelassembly,slidethehexshaft
out of the right side of the unit. The spacer on the left
side of the hex shaft will fall and the sprocket should
remain hanging lose in the chain.
• Liftthefrictionwheelassemblyoutbetweentheaxle
shaft and the drive shaft assemblies.
• Removefourscrewssecuringthefrictionwheelrubber
between the friction wheel plates. See Figure 6-13.
Discard old rubber.
• Reassemblethenewfrictionwheelrubbertothe
friction wheel assembly, tightening the four screws
in rotation and with equal force. It is important to as-
semble the rubber on the friction wheel symmetrically
for proper functioning.
• Insertthepinfromtheshiftarmassemblyintothe
friction wheel assembly and hold assembly in position.
Refer to Figure 6-14 .
• Slide the hex shaft through the right side of the housing
and through the friction wheel assembly.
• Insert the hex shaft through the sprocket and the
spacer. Make certain that the chain engages both the
large and the small sprocket.
NOTE: If the sprocket fell from the snow thrower while
removing the hex shaft, align sprocket on chain, place
the sprocket on the hex shaft. Position the hex hub of
the sprocket toward the friction wheel when sliding the
sprocket on to the hex shaft.
• Slidethebearingontotheleftendofthehexshaftand
press into the hole on the left side the frame.
• Securewiththecuppedwasherandhexboltremoved
earlier.
• Securetheframecoverwithself-tappingscrews.Put
the snow thrower down to its normal operating position.
Friction Wheel
Figure 6-13
Figure 6-14
Figure 6-12
Remove hex
screw and
washer
Friction
Wheel
Assembly
Slide
hex shaft
Hex Shaft
4. Install the new belt on the pulleys in the
reverse order and re-tension with the idler
pulley.
5. Reassemble your unit by performing the
previous steps in the opposite order.
Changing Friction Wheel
Rubber
WARNING: Run the engine
completely dry of gasoline
before tipping snowthrower.
• Tipthesnowthrowerupandforward,so
that it rests on the housing.
• Removescrewsfromtheframecover
underneath the snow thrower. See Figure 5-2.
• Remove the right wheel(s) from the axle.
• Usinga3/4”wrench,holdthehexshaftand
Shift Arm
20
7
Off-Season
Storage
Never store snow
thrower with fuel
in tank indoors or
in poorly ventilated
areas, where fuel
fumes may reach an
open flame, spark
or pilot light as on a
furnace, water heater,
clothes dryer or gas
appliance.
WARNING
If unit is to be stored over 30 days, prepare for storage
as instructed in the separate engine manual packed with
your snow thrower.
Clean snow thrower thoroughly.•
Lubricate as instructed in the Maintenance section of •
this manual.
Refer to engine manual for correct engine storage •
instructions.
Store the snow thrower in a clean, dry area.•
When storing any type of power equipment in a •
poorly ventilated or metal storage shed, care should
be taken to rustproof the equipment, especially
springs, cables and all moving parts.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56

Columbia 769-04101 Manuel utilisateur

Catégorie
Souffleuses à neige
Taper
Manuel utilisateur
Ce manuel convient également à

dans d''autres langues