Cabletron Systems GIGAswitch GSR-16 Getting Started Manual

DIGITAL GIGAswitch/Router

Getting Started Guide

December 1999

This manual describes how to install and set up the DIGITAL

GIGAswitch/Router (GSR).

Revision/Update Information: This is a revised document.

Part Number: 9032681-04

Changes

Cabletron Systems reserves the right to make changes in specifications and other information

contained in this document without prior notice. The reader should in all cases consult Cabletron

Systems to determine whether any such changes have been made.

The hardware, firmware, or software described in this manual is subject to change without notice.

Disclaimer

IN NO EVENT SHALL CABLETRON SYSTEMS BE LIABLE FOR ANY INCIDENTAL, INDIRECT,

SPECIAL, OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING BUT NOT LIMITED

TO LOST PROFITS) ARISING OUT OF OR RELATED TO THIS MANUAL OR THE INFORMATION

CONTAINED IN IT, EVEN IF CABLETRON SYSTEMS HAS BEEN ADVISED OF, KNOWN, OR

SHOULD HAVE KNOWN, THE POSSIBILITY OF SUCH DAMAGES.

Copyright

Printed in the United States of America

Trademarks

Cabletron Systems and SPECTRUM are registered trademarks and Cabletron, clearVISN, and

GIGAswitch are trademarks of Cabletron Systems, Inc.

DIGITAL, DEC, and the DIGITAL logo are registered trademarks of DIGITAL Equipment Corporation.

HP is a registered trademark and OpenView is a trademark of Hewlett-Packard Company.

Pentium is a registered trademark of Intel Corporation.

Microsoft, Windows, and Windows NT are registered trademarks of Microsoft Corporation.

Netscape Navigator is a registered trademark of Netscape Communications Corporation.

Java and Solaris are trademarks of Sun Microsytems, Inc.

All other product names mentioned in this manual may be trademarks or registered trademarks of

their respective companies.

FCC Notice — Class A Computing Device

iii

FCC Notice — Class A Computing Device

This equipment generates, uses, and may emit radio frequency energy. The equipment has been type

tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of FCC

rules, which are designed to provide reasonable protection against such radio frequency interference.

Operation of this equipment in a residential area may cause interference in which case the user at his

own expense will be required to take whatever measures may be required to correct the interference.

Any modifications to this device - unless expressly approved by the manufacturer - can void the user's

authority to operate this equipment under part 15 of the FCC rules.

Industry Canada Notice

This digital apparatus does not exceed the Class A limits for radio noise emissions from digital

apparatus set out in the Radio Interference Regulations of the Canadian Department of

Communications.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables

aux appareils numériques de la class A prescrites dans le Règlement sur le brouillage radioélectrique

édicté par le ministère des Communications du Canada.

NOTICE: The Industry Canada label identifies certified equipment. This certification means that the

equipment meets telecommunications network protective, operational and safety requirements as

prescribed in the appropriate Terminal Equipment Technical Requirements document(s). The

department does not guarantee the equipment will operate to the user’s satisfaction.

Before installing this equipment, users should ensure that it is permissible to be connected to the

facilities of the local telecommunications company. The equipment must also be installed using an

acceptable method of connection. The customer should be aware that compliance with the above

conditions may not prevent degradation of service in some situations.

Repairs to certified equipment should be coordinated by a representative designated by the supplier.

Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give

the telecommunications company cause to request the user to disconnect the equipment.

Users should ensure for their own protection that the electrical ground connections of the power

utility, telephone lines and internal metallic water pipe system, if present, are connected together. This

precaution may be particularly important in rural areas. Caution: Users should not attempt to make

such connections themselves, but should contact the appropriate electric inspection authority, or

electrician, as appropriate.

NOTICE: The Ringer Equivalence Number (REN) assigned to each terminal device provides an

indication of the maximum number of terminals allowed to be connected to a telephone interface. The

termination on an interface may consist of any combination of devices subject only to the requirement

that the sum of the ringer equivalence Numbers of all the devices does not exceed 5.

VCCI Notice — Class A Computing Device

iv

VCCI Notice — Class A Computing Device

This equipment is a Class A product (information equipment to be used in commercial and/or

industrial areas) and conforms to the standards set by the Voluntary Control Council for Interference

by Data Processing Equipment and Electronic Office Machines aimed at preventing radio interference

in commercial and/or industrial areas. Consequently, when used in a residential area or in an adjacent

area thereto, radio interference may be caused to radios and TV receivers. Read the instructions for

correct handling.

Taiwanese Notice — Class A Computing Device

CE Notice — Class A Computing Device

Warning!

This is a Class A product. In a domestic environment, this product may cause radio interference, in

which case the user may be required to take adequate measures.

Achtung!

Dieses ist ein Gerät der Funkstörgrenzwertklasse A. In Wohnbereichen können bei Betrieb dieses Gerätes

Rundfunkstörungen auftreten, in welchen Fällen der Benutzer für entsprechende Gegenma

ß

nahmen

verantwortlich ist.

Avertissement!

Cet appareil est un appareil de Classe A. Dans un environnement résidentiel cet appareil peut provoquer

des brouillages radioélectriques. Dans ce cas, il peut être demandé à l'utilisateur de prendre les mesures

appropriées.

Cabletron Systems, Inc. Program License Agreement

v

Cabletron Systems, Inc. Program License Agreement

IMPORTANT: Before utilizing this product, carefully read this License Agreement.

This document is an agreement between you, the end user, and Cabletron Systems, Inc. (“Cabletron”)

that sets forth your rights and obligations with respect to the Cabletron software program (the

“Program”) contained in this package. The Program may be contained in firmware, chips or other

media. BY UTILIZING THE ENCLOSED PRODUCT, YOU ARE AGREEING TO BECOME BOUND

BY THE TERMS OF THIS AGREEMENT, WHICH INCLUDES THE LICENSE AND THE

LIMITATION OF WARRANTY AND DISCLAIMER OF LIABILITY. IF YOU DO NOT AGREE TO THE

TERMS OF THIS AGREEMENT, PROMPTLY RETURN THE UNUSED PRODUCT TO THE PLACE

OF PURCHASE FOR A FULL REFUND.

Cabletron Software Program License

1. LICENSE. You have the right to use only the one (1) copy of the Program provided in this package

subject to the terms and conditions of this License Agreement.

You may not copy, reproduce or transmit any part of the Program except as permitted by the

Copyright Act of the United States or as authorized in writing by Cabletron.

2. OTHER RESTRICTIONS

. You may not reverse engineer, decompile, or disassemble the Program.

3. APPLICABLE LAW

. This License Agreement shall be interpreted and governed under the laws

and in the state and federal courts of New Hampshire. You accept the personal jurisdiction and

venue of the New Hampshire courts.

Exclusion of Warranty and Disclaimer of Liability

1. EXCLUSION OF WARRANTY. Except as may be specifically provided by Cabletron in writing,

Cabletron makes no warranty, expressed or implied, concerning the Program (including its

documentation and media).

CABLETRON DISCLAIMS ALL WARRANTIES, OTHER THAN THOSE SUPPLIED TO YOU BY

CABLETRON IN WRITING, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT

LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE, WITH RESPECT TO THE PROGRAM, THE ACCOMPANYING

WRITTEN MATERIALS, AND ANY ACCOMPANYING HARDWARE.

2. NO LIABILITY FOR CONSEQUENTIAL DAMAGES

. IN NO EVENT SHALL CABLETRON OR

ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER (INCLUDING, WITHOUT

LIMITATION, DAMAGES FOR LOSS OF BUSINESS, PROFITS, BUSINESS INTERRUPTION,

LOSS OF BUSINESS INFORMATION, SPECIAL, INCIDENTAL, CONSEQUENTIAL, OR

RELIANCE DAMAGES, OR OTHER LOSS) ARISING OUT OF THE USE OR INABILITY TO USE

THIS CABLETRON PRODUCT, EVEN IF CABLETRON HAS BEEN ADVISED OF THE

POSSIBILITY OF SUCH DAMAGES. BECAUSE SOME STATES DO NOT ALLOW THE

EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL

DAMAGES, OR ON THE DURATION OR LIMITATION OF IMPLIED WARRANTIES, IN SOME

INSTANCES THE ABOVE LIMITATIONS AND EXCLUSIONS MAY NOT APPLY TO YOU.

SAFETY INFORMATION

vi

United States Government Restricted Rights

The enclosed product (a) was developed solely at private expense; (b) contains “restricted computer

software” submitted with restricted rights in accordance with Section 52227-19 (a) through (d) of the

Commercial Computer Software - Restricted Rights Clause and its successors, and (c) in all respects is

proprietary data belonging to Cabletron and/or its suppliers.

For Department of Defense units, the product is licensed with “Restricted Rights” as defined in the

DoD Supplement to the Federal Acquisition Regulations, Section 52.227-7013 (c) (1) (ii) and its

successors, and use, duplication, disclosure by the Government is subject to restrictions as set forth in

subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at 252.227-7013.

Cabletron Systems, Inc., 35 Industrial Way, Rochester, New Hampshire 03867-0505.

SAFETY INFORMATION

CLASS 1 LASER TRANSCEIVERS

The DGSRF-AA 100Base-FX Module, DGSRS-AA 1000Base-LX Module, and DGSRL-AA 1000Base-

LX Module use Class 1 Laser transceivers. Read the following safety information before installing

or operating these modules.

The Class 1 laser transceivers use an optical feedback loop to maintain Class 1 operation limits. This

control loop eliminates the need for maintenance checks or adjustments. The output is factory set, and

does not allow any user adjustment. Class 1 Laser transceivers comply with the following safety

standards:

• 21 CFR 1040.10 and 1040.11 U.S. Department of Health and Human Services (FDA).

• IEC Publication 825 (International Electrotechnical Commission).

• CENELEC EN 60825 (European Committee for Electrotechnical Standardization).

When operating within their performance limitations, laser transceiver output meets the Class 1

accessible emission limit of all three standards. Class 1 levels of laser radiation are not considered

hazardous.

Laser Radiation and Connectors

When the connector is in place, all laser radiation remains within the fiber. The maximum amount of

radiant power exiting the fiber (under normal conditions) is -12.6 dBm or 55 x 10

-6

watts.

Removing the optical connector from the transceiver allows laser radiation to emit directly from the

optical port. The maximum radiance from the optical port (under worst case conditions) is

0.8 W cm

-2

or 8 x 10

3

W m

2

sr-1.

Do not use optical instruments to view the laser output. The use of optical instruments to view

laser output increases eye hazard. When viewing the output optical port, power must be removed

from the network adapter.

DECLARATION OF CONFORMITY

vii

DECLARATION OF CONFORMITY

Application of Council Directive(s): 89/336/EEC

73/23/EEC

Manufacturer’s Name: Cabletron Systems, Inc.

Manufacturer’s Address: 35 Industrial Way

PO Box 5005

Rochester, NH 03867

European Representative Name: Mr. J. Solari

European Representative Address: Cabletron Systems Limited

Nexus House, Newbury

Business Park

London Road, Newbury

Berkshire RG13 2PZ, England

Conformance to Directive(s)/Product Standards:

EC Directive 89/336/EEC

EC Directive 73/23/EEC

EN 55022

EN 50082-1

EN 60950

Equipment Type/Environment: Networking Equipment, for

use in a Commercial or Light

Industrial Environment.

We the undersigned, hereby declare, under our sole responsibility, that the equipment packaged with

this notice conforms to the above directives.

Manufacturer Legal Representative in Europe

Mr. Ronald Fotino Mr. J. Solari

Full Name Full Name

Principal Compliance Engineer Managing Director - E.M.E.A.

Title Title

Rochester, NH, USA Newbury, Berkshire, England

Location Location

DIGITAL GIGAswitch/Router Getting Started Guide ix

Contents

About This Guide..................................................................................... xi

Who Should Read This Guide?............................................................................................ xi

How to Use This Guide......................................................................................................... xi

Related Documentation........................................................................................................ xii

Correspondence..................................................................................................................... xii

Getting Help..........................................................................................................................xiii

Safety....................................................................................................... xv

Overview................................................................................................................................ xv

Safety Requirements ............................................................................................................xvi

Chapter 1: Features Overview ................................................................. 1

Specifications ............................................................................................................................2

Features......................................................................................................................................5

Hardware Overview..............................................................................................................10

Chapter 2: Hardware Installation .......................................................... 29

Safety Considerations............................................................................................................29

Hardware Specifications.......................................................................................................30

Installing the Hardware ........................................................................................................31

Chapter 3: Software Installation and Setup ......................................... 51

Installing a PCMCIA Flash Card .........................................................................................52

Powering On and Booting the Software .............................................................................53

Starting the Command Line Interface.................................................................................53

Setting the Basic System Information..................................................................................56

Setting Up SNMP Community Strings ...............................................................................59

Setting Up Passwords............................................................................................................61

Setting the DNS Domain Name and Address....................................................................62

Setting the SYSLOG Parameters ..........................................................................................64

Loading the System Image Software...................................................................................66

Loading the Boot PROM Software ......................................................................................67

Activating the Configuration Changes and Saving the Configuration File ..................68

Contents

x DIGITAL GIGAswitch/Router Getting Started Guide

Chapter 4: Installing and Starting DIGITAL clearVISN CoreWatch....... 71

What Is DIGITAL clearVISN CoreWatch?......................................................................... 72

System Requirements ........................................................................................................... 72

Installing DIGITAL clearVISN CoreWatch ....................................................................... 73

Starting DIGITAL clearVISN CoreWatch.......................................................................... 75

Appendix A: Troubleshooting................................................................ 79

Index ........................................................................................................ 83

DIGITAL GIGAswitch/Router Getting Started Guide xi

About This Guide

This guide provides a general overview of the 8-slot and 16-slot DIGITAL

®

GIGAswitch

™

/Router (GSR-8 and GSR-16) hardware and software features. It provides

procedures for installing the GSR-8 and GSR-16 and setting them up for management

using DIGITAL clearVISN

™

CoreWatch software. For product information not available

in this guide, see the manuals listed in “Related Documentation” on page xii.

Who Should Read This Guide?

Read this guide if you are a network administrator responsible for installing and setting

up the GSR-8 or GSR-16.

Note:

Only qualified personnel should perform the installation procedures in this

guide.

How to Use This Guide

If You Want To... See...

Get an overview of the GSR-8 and GSR-16

software and hardware features

Chapter 1, ”Features Overview”

Install the GSR-8 or GSR-16 hardware Chapter 2, ”Hardware Installation”

Install the GSR-8 or GSR-16 software, boot

the software, and set up the unit

Chapter 3, ”Software Installation and

Setup”

Set up the GSR-8 or GSR-16 for

management using clearVISN CoreWatch

Chapter 4, ”Installing and Starting

DIGITAL clearVISN CoreWatch”

Troubleshoot installation problems Appendix A, ”Troubleshooting”

Contact DIGITAL Technical Support “Getting Help” on page xiii

Contact DIGITAL for technical support “Correspondence” on page xii and

“Getting Help” on page xiii

About This Guide

xii DIGITAL GIGAswitch/Router Getting Started Guide

Related Documentation

The DIGITAL documentation set includes the following items. Refer to these other

documents to learn more about your product.

Correspondence

Documentation Comments

If you have comments or suggestions about this manual, send them to the DIGITAL

Network Products Organization.

Attn.: Documentation Project Manager

E-MAIL: doc_quality@lkg.mts.dec.com

Online Services

To locate product-specific information, refer to the DIGITAL Network Products Home

Page on the World Wide Web located at the following addresses:

For Information About... See the...

Managing the GSR-8 or GSR-16 using the

clearVISN CoreWatch application

DIGITAL clearVISN CoreWatch User’s Guide

and the clearVISN CoreWatch online help

How to use Command Line Interface

(CLI) commands to configure and

manage the GSR-8 or GSR-16

DIGITAL GIGAswitch/Router User Reference

Manual

The complete syntax for all CLI

commands

DIGITAL GIGAswitch/Router Command Line

Interface Reference Manual

SYSLOG messages DIGITAL GIGAswitch/Router Error

Reference Manual

Americas: http://www.networks.digital.com

Europe: http://www.networks.europe.digital.com

Asia Pacific: http://www.networks.digital.com.au

DIGITAL GIGAswitch/Router Getting Started Guide xiii

About This Guide

Getting Help

To expedite your inquiry when you contact your DIGITAL representative, please provide

the following information:

• Your Name

• Your Company Name

•Address

• Email Address

• Phone Number

• FAX Number

• Detailed description of the issue (including history, what you’ve tried, and conditions

under which you see this occur)

• Hardware module number, software version, and switch configuration (that is, what

part types are in what slots)

DIGITAL GIGAswitch/Router Getting Started Guide xv

Safety

Overview

Any warning or caution that appears in this manual is defined as follows

:

WARNING Warns against an action that could result

in equipment damage, personal injury, or

death.

VORSICHT Warnt den Benutzer vor Aktionen, die das

Gerät beschädigen, Personen verletzen

oder sogar zum Tot führen könnten.

DANGER Déconseille à l'utilisateur d'exécuter une

action pouvant entraîner des dommages

matériels, corporels voire la mort.

AVISO Previene contra una acción que podría

dañar el equipo, provocar daños

personales o la muerte.

CAUTION Contains information essential to avoid

damage to the equipment.

ACHTUNG Liefert wichtige Informationen, um einen

Geräteschaden zu vermeiden.

ATTENTION Informations indispensables permettant

d'éviter les dommages matériels.

PRECAUCIÓN Contiene información esencial para evitar

daños al equipo.

Safety

xvi DIGITAL GIGAswitch/Router Getting Started Guide

Safety Requirements

The warnings or cautions that must be observed for the hardware described in this

manual are listed below in English, German, French, and Spanish:

Warnings

WARNING Do not use optical instruments to view the laser output. The use

of optical instruments to view laser output increases eye hazard.

When viewing the output optical port, power must be removed

from the network adapter.

VORSICHT Zum Ansehen der Laserausgabe dürfen keine optischen Geräte

benutzt werden, da dadurch das Risiko von Augenverletzungen

erhöht wird. Vor dem Ansehen des optischen

Ausgangsanschlusses muß der Netzwerkadapter vom

Stromanschluß getrennt werden.

DANGER N'utilisez pas d'instruments d'optique pour voir la sortie du

laser. Leur usage augmente les risques de lésions oculaires.

Lorsque vous voyez le port optique de la sortie, vous devez

couper l'alimentation de l'adaptateur de réseau.

AVISO No utilice instrumentos ópticos para ver la salida de láser. El uso

de instrumentos ópticos para ver una salida de láser incrementa

los daños en los ojos. Al ver el puerto óptico de salida, se debe

retirar la alimentación del adaptador de red.

DIGITAL GIGAswitch/Router Getting Started Guide xvii

Safety

WARNING To prevent personal injury, follow these safety precautions when

installing and using the GIGAswitch/Router.

• To avoid back strain, be careful when lifting the chassis out of

the shipping box.

• Never attempt to rack mount the GIGAswitch/Router chassis

unaided. Ask an assistant to help you hold the chassis.

• Never operate the GIGAswitch/Router with exposed power-

supply bays or module slots. You can leave the PCMCIA slots

exposed but make sure you do not place any tools or body

parts in the PCMCIA slot.

• Never operate the GIGAswitch/Router if the chassis becomes

wet or the area where the chassis is installed is wet.

VORSICHT Beachten Sie bei der Installation und Verwendung von

GIGAswitch/Router die folgenden Sicherheitsbestimmungen,

um Verletzungen zu vermeiden.

• Seien Sie beim Herausheben des Gehäuses aus der

Verpackung vorsichtig, um Rückenschmerzen zu vermeiden.

• Bauen Sie das Gehäuse des GIGAswitch/Router nicht ohne

Hilfe anderer ein. Bitten Sie jemanden, Ihnen beim Halten des

Gehäuses zu helfen.

• Betreiben Sie den GIGAswitch/Router nie mit geöffneten

Netzteilabteilen oder Modulsteckplätzen. Sie können die

PCMCIA-Steckplätze offen lassen. Achten Sie aber darauf,

keine Gegenstände in die PCMIA-Steckplätze einzuführen,

und greifen Sie nicht in die Steckplätze hinein.

• Betreiben Sie den GIGAswitch/Router nicht, wenn das

Gehäuse oder die Umgebung feucht sind.

Safety

xviii DIGITAL GIGAswitch/Router Getting Started Guide

DANGER Pour éviter tout dommage corporel, suivez les consignes de

sécurité lorsque vous installez et que vous utilisez le

GIGAswitch/Router.

• Soyez prudent lorsque vous soulevez le boîtier pour le retirer

de son emballage, faute de quoi vous risquez de vous faire

mal au dos.

• Ne tentez pas d'installer le boîtier du GIGAswitch/Router

sans aide. Faites-vous aider par quelqu'un et demandez-lui de

vous tenir le boîtier.

• N'utilisez pas le GIGAswitch/Router lorsque les

compartiments d'alimentation électrique ou les logements

pour modules sont exposés. Les emplacements pour cartes

PCMCIA peuvent être exposés, mais veillez à ne pas y insérer

d'outils et ni mettez pas vos doigts.

• Vous ne devez en aucun cas utiliser le GIGAswitch/Router si

le boîtier ou l'endroit dans lequel il est stocké est mouillé.

AVISO Para evitar daños personales, siga las normas de seguridad

siguientes cuando instale o utilice GIGAswitch/Router.

• Para evitar daños en la espalda, extreme las precauciones

cuando extraiga la carcasa de su embalaje.

• Nunca intente montar en bastidor la carcasa del

GIGAswitch/Router sin ayuda. Pida a alguien que le ayude a

sujetar la carcasa.

• Nunca ponga en funcionamiento el GIGAswitch/Router con

módulos o ranuras de módulos expuestos a una fuente de

alimentación. Puede dejar las ranuras de PCMCIA expuestas

aunque debe asegurarse de no colocar ningún objeto o parte

del cuerpo en dichas ranuras.

• Nunca ponga en funcionamiento el GIGAswitch/Router si la

carcasa o el área donde se ha instalado se encuentra húmeda.

DIGITAL GIGAswitch/Router Getting Started Guide xix

Safety

WARNING To avoid back strain, be careful when lifting the chassis out of the

shipping box.

VORSICHT Seien Sie bei Herausheben des Gehäuses aus der Verpackung

vorsichtig, um Rückenprobleme zu vermeiden.

DANGER Soyez prudent lorsque vous soulevez le boîtier pour le retirer de

son emballage, faute de quoi vous risquez de vous faire mal au

dos.

AVISO Para evitar daños en la espalda, extreme las precauciones cuando

extraiga la carcasa de su embalaje.

WARNING The GIGAswitch/Router supports hot swapping. This means

you can remove and insert line cards while the

GIGAswitch/Router is operating. However, you cannot insert

tools or body parts inside the chassis while it is powered on.

Doing so can cause electrical shock or equipment damage.

VORSICHT Der GIGAswitch/Router unterstützt Auswechseln von Modulen

während des Betriebs. Allerdings dürfen Sie keine Gegenstände

ins Gerät einführen oder ins Gerät greifen, solange es

eingeschaltet ist. Sie könnten einen elektrischen Schlag erhalten

oder zumindest das Gerät beschädigen.

DANGER Le GIGAswitch/Router permet les branchements à chaud. Vous

pouvez donc retirer et insérer des cartes lorsque le

GIGAswitch/Router est activé. Toutefois, ne touchez pas le

boîtier avec des outils ou avec vos doigts lorsqu'il est sous

tension. Dans le cas contraire, vous risquez de provoquer un

court-circuit ou d'endommager votre matériel.

AVISO GIGAswitch/Router soporta el intercambio de conexión sin

interrupción del funcionamiento. Esto significa que puede retirar

e insertar tarjetas de línea mientras GIGAswitch/Router está

funcionando. Sin embargo, no inserte ninguna herramienta o

parte del cuerpo dentro de la carcasa cuando ésta esté conectada

a la alimentación. Podría tener como consecuencia una descarga

eléctrica o daños en el equipo.

Safety

xx DIGITAL GIGAswitch/Router Getting Started Guide

Cautions

CAUTION To ensure that the fan module can provide adequate cooling,

always provide at least 3 inches of clearance around the top and

bottom of the chassis.

ACHTUNG Um sicherzustellen, daß das Ventilatormodul ausreichende

Kühlung bietet, sollten oberhalb und unterhalb des Gehäuses

stets 3 Zoll Mindestabstand eingehalten werden.

ATTENTION Pour que le module de ventilation fonctionne correctement, vous

devez dégager les côtés du boîtier.

PRECAUCIÓN Para asegurarse de que el módulo del ventilador puede facilitar

la refrigeración adecuada, deje siempre al menos 7,5 centímetros

(3 pulgadas) de espacio libre alrededor de la parte superior e

inferior del chasis.

La page charge ...

Cabletron Systems GIGAswitch GSR-16 Getting Started Manual

Ce manuel convient également à

Cabletron Systems GIGAswitch GSR-16 Getting Started Manual

dans d''autres langues

Documents connexes

Autres documents