Maruyama H23DR Le manuel du propriétaire

Catégorie
Taille-haies électriques
Taper
Le manuel du propriétaire
Équipement pour utilisation à l’extérieur de quali supérieure
L i sez a tte ntivement l inté gra lité du présent manue l a vant d’utiliser ce p r oduit.
E xtraor din air e .
H23DR, H23DLR, H23
HEDGE TRIMMER
TAILLE-HAIE
CORTASETOS
OWNER'S / OPERATOR'S MANUAL
MANUEL D'UTILISATION
MANUAL DEL PROPIETARIO
Equ i p o de c alidad sup erior pa r a uso en exterior e s
A ntes de utiliza r est e p r odu c t o, l ea at e ntamente est e manual.
E xtraordi n a r io.
English
1
Limited Warranty Statement
All Maruyama commercial/ industrial products are warranted to the original purchaser to be free from defects
in material and workmanship from the date of purchase for the time periods listed as follows:
Lifetime for inner drive shaft on trimmers and brushcutters and all ignition modules.
3 years for residential, non-institutional, non-income producing use.
1 year for industrial, commercial, institutional, rental and income producing use.
Maruyama AE series engines and Kawasaki TEX45/TEX54 are covered exclusively for one additional
year of industrial, commercial, institutional, rental and income producing use (total of 2 years).
All other engines refer to engine manufacturer's warranty statement.
Any part of a Maruyama product found to be defective within the applicable warranty period shall, at
Maruyama's option, be repaired or replaced without charge. Warranty consideration is obtained by deliver-
ing any Maruyama product believed to be defective to an Authorized Maruyama Servicing Dealer within the
applicable warranty period.
The purchaser shall not be charged for diagnostic labor that leads to the determination that a warranted part
is defective, if the diagnostic work is performed at a Maruyama Dealer.
Any warranted part which is not scheduled for replacement as required maintenance, or which is scheduled
only for regular inspection to the effect of "repair or replace as necessary" shall be warranted for the warranty
period. Any warranted part, which is scheduled for replacement as, required maintenance shall be warranted
for the period of time up to the first scheduled replacement point for that part. Maruyama Mfg. Co., Inc. is lia-
ble for damages to other engine components caused by the failure of a warranted part still under warranty.
The purchaser is responsible for the performance of the required maintenance, as defined by Maruyama
Mfg. Co., Inc. in the Owner's/Operator's Manual.
EMISSION-RELATED PARTS WARRANTY: In addition to the above warranty coverage, Maruyama Mfg.
Co., Inc. will repair or replace, free of charge, for the original purchaser and each subsequent purchaser any
emission-related part or parts found to be defective in material and workmanship for two (2) years from origi-
nal retail delivery date except catalytic converter. Catalytic converter is warranted one year from origi-
nal retail delivery date. Emission-related parts are the carburetor assembly, the ignition coil
assembly, the ignition rotor and the spark plug and catalytic converter. Any replacement part that is
equivalent in performance and durability may be used in non-warranty maintenance or repairs, and shall not
reduce the warranty obligations of Maruyama Mfg. Co., Inc.
Effective June 1, 2000
English
2
This warranty does not cover the following:
1. Maintenance items (excluding defects in materials and workmanship) including hoses, spark plugs,
starter rope, air and fuel filters, clutch shoes, vibration isolators, throttle cables and all cutting attach-
ments, etc.
2. Extra expenses including shipping and handling, travel, payment for lost time or pay and for any inconve-
nience and storage.
3. Alterations or modifications including aftermarket parts not authorized by Maruyama U.S., Inc.
4. Wear, accident, abuse, neglect, misuse, negligence, improper fuels, lubricants, fuel mixtures (when appli-
cable), or failure to operate or maintain the product in accordance with instructions approved by
Maruyama.
Repair or replacement as provided under this warranty is the exclusive remedy of the consumer. Maruyama
shall not be liable for any incidental or consequential damages for breach of any express or implied warranty
on these products except to the extent prohibited by applicable law. Any implied warranty of merchantability
or fitness for a particular purpose on these products is limited in duration to the warranty period as defined in
the limited warranty statement. Maruyama reserves the rights to change or improve the design of the prod-
uct without notice and does not assume obligation to update previously manufactured products.
This warranty provides you with specific legal rights, which may vary from state to state.
It is the Owner's and Dealer's responsibility to make sure the Warranty Registration Card is properly filled out
and mailed to Maruyama U.S., Inc. Proof of purchase and registration will be required in order to obtain war-
ranty service.
To locate an Authorized Maruyama Servicing Dealer nearest you, contact:
.
Maruyama U.S., Inc.
4770 Mercantile Drive, suite 100,
Fort Worth, TX 76137
(940) 383-7400
maruyama@maruyama-us.com
www.maruyama-us.com
Effective June 1, 2000
English
3
FEDERAL EMISSION CONTROL WARRANTY STATEMENT
YOUR WARRANTY RIGHTS AND OBLIGATIONS
The U.S. Environmental Protection Agency (EPA) and Maruyama Manufacturing Company, Inc.
are pleased to explain the emission control system warranty on your small off-road engine. New
1997 and later model year small off-road engines must be designed, built and equipped, at the
time of sale, to meet the U.S. EPA regulations for small off-road engines. The equipment engine
must be free from defects in materials and workmanship which cause it to fail to conform with U.S.
EPA standards for the first two years of engine use from the date of sale to the ultimate purchaser.
Maruyama Manufacturing Company, Inc. must warrant the emission control system on your small
off-road engine for the period of time listed above provided there has been no abuse, neglect or
improper maintenance of your small off-road engine.
Emission durability of 300 hours.
Your emission control system may include parts such as the carburetor or fuel injection system,
the ignition system, and catalytic converter. Also included may be hoses, belts, and connectors
and other emission related assemblies.
Where a warrantable condition exists, Maruyama Manufacturing Company, Inc. will repair your
small off-road engine at no cost to you, including diagnosis (if the diagnostic work is performed
at an authorized dealer), parts, and labor.
MANUFACTURER'S WARRANTY COVERAGE:
The 1997 and later model year small off-road engines are warranted for two years. If any
emission-related part on your engine is defective, the part will be repaired or replaced by
Maruyama Manufacturing Company, Inc. free of charge.
The engine exhaust from this product
contains chemicals known to the State
of California to cause cancer, birth
defects or other reproductive harm.
WARNING
:
2
0
4
6
8
10
THE AIR INDEX OF THIS ENGINE IS 3
MOST CLEAN
NOTE:THE LOWER THE AIR INDEX, THE LESS POLLUTION
THIS ENGINE IS CERTIFIED TO BE EMISSIONS
COMPLIANT FOR THE USE:EXTENDED: 300HOURS
CHECK THE OWNER'S MANUAL FOR FURTHER DETAILS
For more information,
Visit us on the web at
www.maruyama-us.com
LEAST CLEAN
.
.
CER230HT
English
4
OWNER'S WARRANTY RESPONSIBILITIES:
(a) As the small off-road engine owner, you are responsible for the performance of the required
maintenance listed in your owner's manual.
Maruyama Manufacturing Company, Inc. recommends that you retain all receipts covering
maintenance on your small off-road engine, but Maruyama Manufacturing Company, Inc.
cannot deny warranty solely for the lack of receipts or for your failure to ensure the
performance of all scheduled maintenance. Any replacement part or service that is
equivalent in performance and durability may be used in non-warranty maintenance or
repairs, and shall not reduce the warranty obligations of the engine manufacturer.
(b) As the small off-road engine owner, you should be aware, however, that Maruyama
Manufacturing Company may deny you warranty coverage if your small off-road engine or a
part has failed due to abuse, neglect, improper maintenance or unapproved modifications.
(c) You are responsible for presenting your small off-road engine to a Maruyama Manufacturing
Company, Inc. service center as soon as a problem exists. The warranty repairs should be
completed in a reasonable amount of time, not to exceed 30 days.
If you have any questions regarding your warranty rights and responsibilities, you should
contact Maruyama U.S., Inc. at 1-866-783-7400, or [email protected].
COVERAGE
Maruyama Manufacturing Company, Inc. warrants to the ultimate purchaser and each
subsequent purchaser that your small off-road engine will be designed, built and equipped, at
the time of sale, to meet all applicable regulations. Maruyama Manufacturing Company, Inc.
also warrants to the initial purchaser and each subsequent purchaser that your small off-road
engine is free from defects in materials and workmanship which cause the engine to fail to
conform with applicable regulations for a period of two years.
The 1997 and later model years, EPA requires manufacturers to small off-road engines for two
years. These warranty periods will begin on the date the small off-road engine is purchased by
the initial purchaser. If any emission-related part on your engine is defective, the part will be
replaced by Maruyama Manufacturing Company, Inc. at no cost to the owner.
Maruyama Manufacturing Company, Inc. shall remedy warranty defects at any authorized
Maruyama Manufacturing Company, Inc. engine dealer or warranty station. Any authorized
work done at an authorized dealer or warranty station shall be free of charge to the owner if
such work determines that a warranted part is defective. Any manufacturer-approved or
equivalent replacement part may be used for any warranty maintenance or repairs on emission-
related parts, and must be provided free of charge to the owner if the part is still under warranty,
Maruyama Manufacturing Company, Inc. is liable for damages to other engine components
caused by the failure of a warranted part still under warranty.
English
5
EPA considers emission-related warranted parts to include all the parts listed below. These
warranted parts are: the carburetor assembly, the ignition coil assembly, the ignition
rotor, the spark plug, the catalytic converter, and the fuel tank.
MAINTENANCE REQUIREMENTS
The owner is responsible for the performance of the required maintenance as defined by the
Maruyama Manufacturing Company, Inc. in the owner's manual.
LIMITATIONS
This Emission Control System Warranty shall not cover any of the following:
(a) repair or replacement required because of misuse or neglect, lack of required maintenance,
repairs improperly performed or replacements not conforming to Maruyama Manufacturing
Company, Inc. specifications that adversely affect performance and/or durability, and
alterations or modifications not recommended or approved in writing by Maruyama
Manufacturing Company, Inc., and
(b) replacement of parts and other services and adjustments necessary for required
maintenance at and after the first scheduled replacement point.
English
6
CALIFORNIA EMISSION CONTROL WARRANTY STATEMENT
YOUR WARRANTY RIGHTS AND OBLIGATIONS
The California Air Resources Board (CARB), and Maruyama Manufacturing Company, Inc. are
pleased to explain the emission control system warranty on your 2014 small off-road engine. In
California, new small off-road engines must be designed, built and equipped to meet the State's
stringent anti-smog standards. Maruyama Manufacturing Company, Inc. must warrant the emission
control system on your small off-road engine for the period of time listed above provided there has
been no abuse, neglect or improper maintenance of your small off-road engine.
Your emission control system may include parts such as the carburetor or fuel injection system, the
ignition system, fuel tank and catalytic converter. Also included may be hoses, belts, and
connectors and other emission related assemblies.
Where a warrantable condition exists, Maruyama Manufacturing Company, Inc. will repair your
small off-road engine at no cost to you, including diagnosis, parts, and labor.
MANUFACTURER'S WARRANTY COVERAGE:
The 1995 and later small off-road engines are warranted for two years. If any emission-related
part on your engine is defective, the part will be repaired or replaced by Maruyama
Manufacturing Company, Inc.
OWNER'S WARRANTY RESPONSIBILITIES:
(a) As the small off-road engine owner, you are responsible for the performance of the required
maintenance listed in your owner's manual.
Maruyama Manufacturing Company, Inc. recommends that you retain all receipts covering
maintenance on your small off-road engine, but Maruyama Manufacturing Company, Inc.
cannot deny warranty solely for the lack of receipts or for your failure to ensure the
performance of all scheduled maintenance
(b) As the small off-road engine owner, you should be aware, however, that Maruyama
Manufacturing Company may deny you warranty coverage if your small off-road engine or a
part has failed due to abuse, neglect, improper maintenance or unapproved modifications.
(c) You are responsible for presenting your small off-road engine to a Maruyama Manufacturing
Company, Inc. distribution center as soon as a problem exists. The warranty repairs should
be completed in a reasonable amount of time, not to exceed 30 days.
English
7
If you have any questions regarding your warranty rights and responsibilities, you should
contact Maruyama U.S., Inc. at 1-866-783-7400, or [email protected].
Emission System Parts
Exhaust Emission
Carburetor
Muffler
Catalytic Converter
Ignition Coil / Magneto
Spark Plug
Air Filter
EGR Valve (piston)
Fuel Filter
Evaporative Emission
Fuel Tank
English
8
FOREWORD
This Ownerʼs/Operatorʼs Manual is designed to familiarize the operator with the various features
and component parts of the equipment and to assist you with the operation and maintenance of
your new Hedge Trimmer.
It is essential that any operator of this Hedge Trimmer product reads and understands the
contents of this manual before using the Hedge Trimmer.
Important safety instructions will be identified by the following safety symbol:
Failure to comply with the instructions in this manual may result in serious injury or death.
For additional assistance, contact any local authorized Maruyama dealer or Maruyama U.S., Inc.,
4770 Mercantile Drive, suite100, Fort Worth, TX 76137
TABLE OF CONTENTS
SPECIFICATIONS
Model H23DR H23DLR H23
Dimensions L x W x H
1080 × 248 × 226
(42.5 × 9.7 × 8.9in)
1240 × 248 × 226
(48.8 × 9.7 × 8.9in)
1135 × 270 × 226
(44.7 × 10.6 × 8.9in)
Dry Weight 5.3kg(11.6lbs.) 5.5kg(12.0lbs.) 5.5kg(12.0lbs.)
Blade Length 600mm(24in) 750mm(30in) 750mm(30in)
Rear Handle Rotational Fixed
Engine Model CER230HT
Engine Displacement
22.5 cm
3
Fuel Tank Capacity
0.4󰙚
Carburetor Walbro Diaphragm Type
Ignition System Solid State
Spark Plug:
Make
Type
Electrode Gap
NGK
BPM8Y
0.6
0.7 mm (0.024
0.028 in.)
Fuel Mixture:
50:1
Using Maruyama 50:1 2-Cycle Engine Oil or any Quality two-cycle engine oil
designed for use in air-cooled, high performance two-cycle engines.
Warranty

1
Foreword

8
Specications

8
Product description

9
Warning

10
Before operation

13
Starting and stopping procedure

16
Carburetor adjustment

17
Operating the Power Hedge Trimmer

18
Regular maintenance

18
Storage

21
Maintenance Period

22
English
9
PRODUCT DESCRIPTION
FUEL TANK
THROTTLE
TRIGGER
REAR
HANDLE
STOP
SWITCH
STARTER GRIP
BLADE
FRONT HANDLE
ENGINE
H23DR, H23DLR
REAR HANDLE
STOP
SWITCH
THrOTTle
TrIgger
lOCK leVer
H23
STOP
SWITCH
STARTER GRIP
BLADE
RIGHT HANDLE
ENGINE
FUEL TANK
THROTTLE
TRIGGER
LEFT
HANDLE
English
10
WARNING
Operator safety
1. Read and understand this Ownerʼs/Operatorʼs Manual before using this product. Be thoroughly
familiar with the proper use of this product.
2. Always wear eye protection that complies with ANSI (American National Standards Institute)
Z87-1.
3. Wear hearing protection.
4. Always wear heavy long pants, boots and gloves. Do not wear
loose clothing, jewelry, short pants, sandals or go barefoot.
Secure hair so it is above shoulder length.
5. Never operate this Hedge Trimmer when you are tired, ill, under the influence of alcohol, drugs
or medication.
6. Never start or run the engine inside a closed room or building.
Breathing exhaust fumes can cause death.
7. Keep handle clean of oil, fuel and dirt.
English
11
Power Hedge Trimmer safety
1. Shut off the engine and wait unit the cutting blades have completely stopped moving before
checking, maintaining or working on the Hedge Trimmer.
2. Inspect the Hedge Trimmer before each use. Replace damaged parts. Check for fuel leaks.
Make sure all fasteners are in place and tightened securely.
3. Inspect the Hedge Trimmer cutting blades and guide. Replace any parts that are cracked,
chipped, or damaged before using the Hedge Trimmer.
4. Never use replacement parts that are not approved by Maruyama U.S., Inc.
5 Maintain the Hedge Trimmer in accordance with the recommended maintenance intervals and
procedures in the maintenance section, pages 18 to 21.
6. If running problems or excessive vibration occur, stop immediately and inspect the unit for the
cause. If the cause cannot be determined or is beyond your ability to correct, return the Hedge
Trimmer to your servicing dealer for repair.
7. Never use the Hedge Trimmer if handles are damaged or handle fasteners are loose.
Always make sure all fasteners (nuts and bolts) are installed and properly tightened.
8. Never use a machine that has been modified so that it no longer corresponds with the original
design.
9. Do not attempt to repair the Hedge Trimmer unless you are qualified to do so.
10. When transporting or storing the Hedge Trimmer always install the blade shield.
Fuel safety
1. Gasoline is highly flammable and must be handled and stored carefully. Use a container
approved for storing gasoline and/or fuel/oil mixture.
2. Mix and pour fuel outdoors and where there are no sparks or
flames.
3. Do not smoke near fuel or the Hedge Trimmer or while using the
Hedge Trimmer.
4. Do not overfill the fuel tank. Stop filling 1/4 - 1/2 inch (6mm-13mm)
from the top of the tank.
5. Wipe up any spilled fuel before starting the engine.
WIPE UP ANY FUEL SPILLAGE
English
12
6. Move the Hedge Trimmer at least 10 feet (3 m) away
from the fueling location before starting the engine.
7. Do not remove the Hedge Trimmer fuel tank cap while
the engine is running or immediately after stopping the
engine.
8. Allow the engine to cool before refueling.
9. Empty the fuel tank before storing the Hedge Trimmer.
Fuel should be emptied after each use. Fuel left in the
tank may leak during storage.
10. Store fuel and Hedge Trimmer away from open
flame, sparks and excessive heat. Make sure fuel
vapors cannot reach sparks or open flames from water
heaters, furnaces, electric motors, etc.
Power Hedge Trimmer operating safety
1. THIS HEDGE TRIMMER CAN CAUSE SERIOUS INJURIES.
Read the instructions carefully. Be familiar with all controls and the proper use of the Hedge
Trimmer.
2. Never allow children to operate the Hedge Trimmer. It is not a toy.
3. Keep the area of operation clear of all persons, particularly small children and pets.
4. The Hedge Trimmer blades are extremely sharp. Do not put hands or feet near or under any
moving parts. Keep body clear at all times.
5. Use the Hedge Trimmer only in daylight or good artificial light.
6. Inspect your work area before you begin. Remove string, rope or similar materials which can
become entangled in the Hedge Trimmer blades.
7. Avoid hidden hazards. Watch for hidden objects within your working area, such as chain link
fencing, cables, wires, telephone and power lines.
8. Never operate the Hedge Trimmer without proper guards or other protective safety devices in
place.
9. Keep a firm footing and balance. Do not over-reach. Do not operate the Hedge Trimmer while
standing on a ladder or similar temporary support.
10. Use the right tool for the job. Do not use the Hedge Trimmer for any job that is not
recommended by the manufacturer.
Min. 10 feet
(3 m)
English
13
11. While operating the Hedge Trimmer be always sure of a safe and secure operating position.
Do not over reach.
12. To reduce fire hazard keep engine and muffler free of debris, leaves, and dry materials.
Always wipe away spilled fuel and excessive lubricant before starting.
13. Always use two hands to operate the Hedge Trimmer.
14. Always be aware of your surroundings and stay alert for possible hazards that you may not
hear due to the noise of the machine.
15. Know how to stop the machine quickly in emergency. (See to stop the engine in STARTING
AND STOPPING PROCEDURE SECTION.)
BEFORE OPERATION
FUELING
WARNING! The following precautions will lessen the risk of fire.
1. Do not smoke near fuel.
2. Mix and pour fuel outdoors and where there are no sparks or flames.
3. Always shut off the engine before refueling. Never remove the Hedge Trimmer fuel tank cap
while the engine is running or immediately after stopping the engine.
4. Always open the fuel tank cap slowly to release any possible pressure inside the tank.
5. Do not overfill the fuel tank. Stop filling 1/4
-
1/2 inch
(6mm-13mm) from the top of the tank.
6. Tighten the tank fuel cap carefully but firmly after refilling.
7. Wipe up any spilled fuel before starting the engine.
8. Move the Hedge Trimmer at least 10 feet (3m) away from the
fueling location and fuel storage container before starting the
engine.
Min. 10 feet
(3 m)
English
14
FUEL; MIXING GASOLINE AND OIL
IMPORTANT The engine used on this Hedge Trimmer is of a 2-cycle design. The internal moving
parts of the engine, i.e., crankshaft bearings, piston pin bearings and piston to wall contact sur-
faces, require oil mixed with the gasoline for lubrication. Failure to add oil to the gasoline or failure
to Mix oil with the gasoline at the appropriate ratio Will cause major engine damage and will void
your warranty. For your fuel premix, use Maruyama Premium 2-Cycle Oil Mix, or equivalent ISO-L-
EGD & JASO FC oil with a minimum 89 octane high Quality gasoline. Maruyama 2-cycle oil is spe-
cially formulated to meet the requirements of high-performance, low-emission air-cooled 2-cycle
engines. Use of other oils may lead to service issues which may Not be covered by your warranty.
FUEL MIXTURE: When using genuine Maruyama 50:1 2-Cycle Oil, or a quality oil designed for
2-cycle air-cooled engines, oil ratio is 50 parts gasoline to 1 part oil or 50:1.
CAUTION! If Maruyama oil is not used, never use a mixing ratio less than 50:1 regardless of the
oil package mixing instructions. Ratios less the 50:1, (for example, 60:1, 80:1, 100:1), reduce
the amount of lubrication to the internal moving parts of the engine and can cause damage.
FUEL MIXTURE CHART:
Gasoline Maruyama 50:1 2-Cycle Oil Gasoline Maruyama 50:1 2-Cycle Oil
1 gallon 2.6 oz. 1 litre 20ml
2 1/2 gallons 6.4 oz. 2 litre 40ml
5 gallons 12.8 oz. 5 litre 100ml
MIXING INSTRUCTIONS: Always mix fuel and oil in a clean container approved for gasoline.
Mark the container to identify it as fuel mix for the Hedge Trimmer. Use regular unleaded gasoline
and fill the container with half the required amount of gasoline. Pour the correct amount of oil
into the container then add the remaining amount of gasoline. Close the container tightly and
shake it momentarily to evenly mix the oil and the gasoline before filling the fuel tank on the Hedge
Trimmer.
When refilling the Hedge Trimmer fuel tank, clean around the fuel tank cap to prevent dirt and
debris for entering the tank during cap removal. Always shake the premix fuel container
momentarily before filling the fuel tank.
Always use a spout or funnel when fueling to reduce fuel spillage. Only fill the tank to within 1/4-
1/2 inch (6mm-13mm) from the top of the tank. Avoid filling to the top of the tank filler neck.
GAS
FILL MARK
HALF GASOLINE ADD OIL ADD REMAINING
GASOLINE
GASOIL
SHAKE
(MIX OIL AND GASOLINE)
English
15
NOTE:
1. Never mix gasoline and oil directly in the Hedge Trimmer fuel tank.
CAUTION!
1. Do not use National Marine Manufacturerʼs Association (NMMA) or BIA certified oils. This type
or 2-cycle engine oil does not have the proper additives for air-cooled, 2-cycle engines and
can cause engine damages.
2. Do not use automotive motor oil. This type of oil does not have the proper additives for air-
cooled, 2-cycled engines and can cause engine damage.
THE CUTTING BLADES
CAUTION-DO NOT TOUCH THE SHARPENED EDGES OF THE CUTTING
BLADES. THE CUTTING BLADES ARE EXTREMELY SHARP AND
DANGEROUS AT ALL TIMES. ALWAYS WEAR GLOVES TO HELP PROTECT
YOUR HANDS AND FINGERS FROM INJURY.
Adjusting the cutting blades are not necessary for model HT233D and HT233DL.
Turn the screw until snug, and fasten with the nut. blades. Blades that are too loose may
vibrate, and will not provide a clean, smooth cut.
ROTATIONAL REAR HANDLE
Rear handle is adjustable to five different positions by pulling the lock lever and turn the
rear handle. Pull the lock lever directly in line with the handle (following the arrow in fig),
then turn the rear handle.It is extremely important that the handle is completely located
and correctly locked in the selected position.
NUT
GUIDE BAR
WASHER
SCREW
NUTS
LOWER BLADE
UPPER BLADE
SCREWS
Do not adjust the rear handle to any other position
than specified five positions.
(Throttle lever does not work when the rear handle is unlocked)
Stop the engine before change the rear handle position.
Make sure the rear handle is locked before start the engine.
During operation, hold the rear handle with upright regardless
the blade direction.
Select the proper handle position to be always sure of a safe
and secure operating position.
LOCK LEVER
English
16
STARTING AND STOPPING PROCEDURE
Before Starting The Engine: Fill the fuel tank as instructed in the BEFORE OPERATION section
of this manual. Rest the Hedge Trimmer on the ground. Make sure that the cutting blades are
clear of branches, shrubs, debris, etc. Keep all bystanders, children and animals away from the
working area.
STARTING THE ENGINE (for the carburetor
with primer bulb)
The carburetors on MARUYAMA engines contain a choke
system and are designed to start at IDLE speed.
1. Push and release the fuel primer bulb located on the
bottom of the carburetor until air bubble free fuel is
seen flowing through the clear fuel return hose bac to
the fuel tank.
2. Move the choke lever to the closed position “
.
When the engine is warm, move the choke lever to the
open position “
”.
3. Set the engine stop switch to the “ON ( | )” position.
The throttle trigger positioned at IDLE.
4. Grasp the starter grip and slowly pull the starter cord
out until you feel some resistance, then pull the cord
quickly and powerfully. Pull the starter grip until the
engine starts. After the engine is started, move the
choke lever to the open position.
5. After starting, allow the engine to run a few minutes to
warm it up before using.
Before starting the engine, place the machine on the ground and make sure the blade is
free from branches and stones.
CHOKe leVer
PrIMer BUlB
FUel-reTUrNe lINe
PUMP
ON ( | )
←→
STOP (O)
STOP SWICH
ON ( | )
←→
STOP (O)
STOP SWICH
English
17
NOTE:
1. Do not pull the starter cord out completely.
2. Do not release the starter cord from the fully extended position.
To Stop The Engine:
1. Release the throttle trigger.
2. Slide the stop switch to the “STOP” position.
CARBURETOR ADJUSTMENT
This Hedge Trimmer is equipped with non-adjustable fuel mixture carburetor. The engine idle
speed is the only adjustment to the Operator.
The cutting blades may be moving during idle speed adjustment. Wear the recommended
personal protective equipment and observe all safety instructions. Keep hands and body away from
blade area.
Engine Idle Speed:
When the throttle trigger is released the engine should return to an idle speed which is 2700-3300
rpm or just below clutch engagement speed. The cutting blades must not move and the engine
should not stall (stop running) at engine idle speed.
The engine idle speed is adjusted by rotating the idle
speed screw on the carburetor. Turning the idle speed
screw in (clockwise) increases engine speed while
turning the screw out decreases engine speed.
If idle speed adjustment is necessary and after adjustment the cutting blades move or the
engine stalls, stop using the Hedge Trimmer immediately!
Contact your local authorized Maruyama Dealer for assistance and servicing.
IDLE SPEED
ADJUSTMENT
SCREW
English
18
OPERATING THE POWER HEDGE TRIMMER
CAUTION—Read the WARNING on page (10) concerning the proper use of the
Hedge Trimmer.
The MARUYAMA Hedge Trimmer is designed for cutting and trimming foliage and small branches
up to 1/4 inches (6mm) in diameter. Although the MARUYAMA Hedge Trimmer is capable of
cutting larger diameter branches, wear and tear of the machine would be proportionally increased.
CAUTION—Always wear gloves and protective clothing when operating the Hedge
Trimmer.
If the cutting blades become jammed, stop the engine immediately. Make certain all moving parts
have stopped and disconnect the spark plug before inspecting the equipment for damage. Never
use a Power Hedge Trimmer that has chipped, cracked, or broken cutting blades.
REGULAR MAINTENANCE
Maintenance, replacement or repair of emission control devices and systems may be performed by
any repair establishment or individual; however, warranty repairs must be performed by a dealer
or service center authorized by Maruyama Manufacturing Company, Inc. with Maruyama U.S.,
Inc. The use of parts that are not equivalent in performance and durability to authorized parts may
impair the effectiveness of the emission control system and may have a bearing on the outcome of a
warranty claim.
AIR FILTER
Maintenance Interval: The air filter should be cleaned
daily or more often when working in extremely dusty condi-
tions and replaced after every 100 hours of operation.
Maintenance: Push and open the air filter cover.
Remove the foam filter. Clean the filter with warm, soapy
water. Let the filter completely dry. Lightly apply SAE 30
motor oil to the foam filter and squeeze out all excess oil.
Reassemble the filter and filter cover.
FUEL FILTER
Maintenance Interval: The fuel filter should be replaced
after every 100 hours of operation.
Maintenance: The fuel filter is attached to the end of the
fuel pick-up hose inside the fuel tank. To replace the fuel
filter, first make sure the fuel tank is empty. Remove the
fuel cap. Using a wire hook, gently pull the fuel filter out
though the fuel filter opening. Grasp the fuel hose next to
the fuel filter fitting and remove the filter but do not
FOAM FILTER
AIR FILTER
COVER
OPEN
FUEL TANK
WIRE
FUEL FILTER
PUSH
English
19
release the hose. While still holding on to the fuel hose, attach the new fuel filter. Drop the fuel
filter back into the fuel tank. Make sure that the fuel filter is not stuck in a corner of the tank and
that the fuel hose is not doubled over (kinked) before refueling.
SPARK PLUG
Maintenance Interval: The spark plug should be remove from the engine and checked after each
25 hours of operation and replaced after every 100 hours of operation.
Maintenance: With the engine at ambient (room) temperature,
twist the high tension lead boot on the spark plug back and forth
a couple of times to loosen boot then pull the boot off of the spark
plug. Remove the spark plug. The electrodes can be cleaned
with a stiff brush. Adjust the electrode air gap to 0.6
0.7 mm
(0.024
0.028 in.). Replace the spark plug if it is oil-fouled,
damaged or if the electrodes are worn down. Do not
overtighten the spark plug when installing. The tightening
torque is 10.7
16.6 Nm (95
148 in. lbs.). Reinstall the cylinder and muffler covers.
CYLINDER COOLING FINS
Maintenance Interval: The cylinder cooling fins should be cleaned after every 25 hours of opera-
tion or once a week which ever comes first. Air must flow freely around and through the cylinder
cooling fins to prevent engine overheating. Leaves, grass, dirt and debris buildup on the fins will
increase the operating temperature of the engine which can reduce engine performance and
short en engine life.
Maintenance: With the engine at ambient (room) temperature, remove the two socket head
screws, and remove the cover (FIG.1). Remove the two socket head screws, and remove the tail
pipe. Loosen the cylinder cover screw (knob) and lift off the cylinder cover. Clean all dirt and
debris from the cooling fins and from around the cylinder base. Reinstall the cylinder cover, tail
pipe and the cover (FIG.2).
TIPS
0.6
0.7 mm
(0.024"
0.028")
1 2
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68

Maruyama H23DR Le manuel du propriétaire

Catégorie
Taille-haies électriques
Taper
Le manuel du propriétaire