Sony XR-CA370X Manuel utilisateur

Actual total number: Sony XR-CA370X/CA370 (GB,DE,FR,IT,NL) 3-246-852-42(1)

 2003 Sony Corporation

FM/MW/LW

Cassette Car Stereo

3-246-852-42 (1)

XR-CA370X

XR-CA370

Operating Instructions

Bedienungsanleitung

Mode d’emploi

Istruzioni per l’uso

Gebruiksaanwijzing

GB

DE

IT

FR

NL

Wichtig!

Bitte nehmen Sie sich etwas Zeit, um den Geräte-Pass

vollständig auszufüllen. Dieser befindet sich auf der

hinteren Umschlagseite dieser Bedienungsanleitung.

Si dichiara che l’apparecchio è stato fabbricato in conformità all’art. 2, Comma 1 del

D.M. 28.08.1995 n. 548.

For installation and connections, see the supplied installation/connections

manual.

Zur Installation und zum Anschluss siehe die mitgelieferte Installations-/

Anschlussanleitung.

En ce qui concerne l’installation et les connexions, consulter le manuel

d’installation/connexions fourni.

Per l’installazione e i collegamenti, fare riferimento al manuale di istruzioni di

installazione/collegamenti in dotazione.

Zie voor het monteren en aansluiten van het apparaat de bijgeleverde handleiding

“Installatie en aansluitingen”.

22

Welcome !

Thank you for purchasing this Sony Cassette

Player.

In addition to the cassette playback and radio

operations, you can expand your system by

connecting an optional CD/MD unit*

1

.

When you operate this unit or a connected

optional CD unit with the CD TEXT function,

the CD TEXT information will appear in the

display when you play a CD TEXT disc*

2

.

*

1

You can connect a CD changer, an MD changer,

a CD player, or an MD player.

*

2

A CD TEXT disc is an audio CD that includes

information such as the disc name, artist name,

and track names.

This information is recorded on the disc.

Precautions

• If your car was parked in direct sunlight

resulting in a considerable rise in

temperature inside the car, allow the unit to

cool off before operating it.

• If no power is being supplied to the unit,

check the connections first. If everything is in

order, check the fuse.

• If no sound comes from the speakers of a

2-speaker system, set the fader control to the

centre position.

• When a tape is played back for a long period,

the cassette may become warm because of

the built-in power amplifier. However, this is

not a sign of malfunction.

If you have any questions or problems

concerning your unit that are not covered in

this manual, please consult your nearest Sony

dealer.

To maintain high quality sound

If you have drink holders near your audio

equipment, be careful not to splash juice or

other soft drinks onto the car audio. Sugary

residues on this unit or cassette tapes may

contaminate the playback heads, reduce the

sound quality, or prevent sound reproduction

altogether.

Cassette cleaning kits cannot remove sugar

from the tape heads.

33

Notes on Cassettes

Cassette care

• Do not touch the tape surface of a cassette, as

any dirt or dust will contaminate the heads.

• Keep cassettes away from equipment with

built-in magnets such as speakers and

amplifiers, as erasure or distortion on the

recorded tape could occur.

• Do not expose cassettes to direct sunlight,

extremely cold temperatures, or moisture.

• Slack in the tape may cause the tape to be

caught in the machine. Before you insert the

tape, use a pencil or similar object to turn the

reel and take up any slack.

• Distorted cassettes and loose labels can cause

problems when inserting or ejecting tapes.

Remove or replace loose labels.

• The sound may become distorted while

playing the cassette. The cassette player head

should be cleaned after each 50 hours of use.

Slack

Cassettes longer than 90 minutes

The use of cassettes longer than 90 minutes is

not recommended except for long continuous

play. The tape used for these cassettes is very

thin and tends to stretch easily. Frequent

playing and stopping of these tapes may cause

them to become entangled in the cassette deck

mechanism.

44

Table of Contents

With Optional EquipmentThis Unit Only

Location of controls ................................................. 5

Getting Started

Resetting the unit ................................................ 6

Detaching the front panel .................................. 6

Setting the clock .................................................. 7

Cassette Player

Listening to a tape ............................................... 7

Radio reception during fast-forwarding or

rewinding of a tape

— Automatic Tuner Activation (ATA) ........ 8

Radio

Storing stations automatically

— Best Tuning Memory (BTM) .................... 8

Storing only the desired stations ...................... 9

Receiving the stored stations ............................. 9

RDS

Overview of the RDS function ........................ 10

Displaying the station name ............................ 10

Retuning the same programme automatically

— Alternative Frequencies (AF) ................ 10

Listening to traffic announcements ................ 12

Presetting the RDS stations with the AF and

TA data ......................................................... 13

Locating a station by programme type .......... 13

Setting the clock automatically ....................... 14

Other Functions

Adjusting the balance and fader ..................... 15

Attenuating the sound ..................................... 15

Changing the sound and display settings ..... 15

Setting the equalizer

— EQ3............................................................ 16

CD/MD Unit

Playing a CD or MD ......................................... 17

Playing tracks repeatedly

— Repeat Play .............................................. 18

Playing tracks in random order

— Shuffle Play .............................................. 18

Additional Information

Maintenance ....................................................... 19

Removing the unit ............................................ 20

Specifications ..................................................... 21

Troubleshooting guide ..................................... 22

55

Location of controls

Refer to the pages listed for details.

1 SOURCE (Radio/CD/MD) button

8, 9, 16, 17

2 MODE button

During radio reception:

Band select 8, 9

During CD/MD playback:

CD/MD unit select 17

3 Volume +/– button 7, 12, 15, 16

4 Z (eject) button 7, 8, 9, 17

5 Display window

6 m/M (fast winding)/DIR (tape

transport direction change) buttons 7, 8

7 SEEK button

Seek 9, 11, 14

Automatic Music Sensor 18

Manual search 18

8 DSPL (display mode change) button

7, 10, 17

9 EQ3 button 16

q; RELEASE (front panel release) button

6, 19

qa SEL (select) button 7, 14, 15, 16, 17

qs RESET button (located on the front side

of the unit behind the front panel) 6

qd AF button 10, 11, 13

qf ATT (attenuate) button 15

qg Number buttons 14, 15, 17

During radio reception:

Preset number select 9, 11, 13

During CD/MD playback:

(1) DISC – 18

(2) DISC + 18

(3) REP 18

(4) SHUF 18

qh PTY (programme type)/ATA button

8, 14

qj TA button 12, 13

qk SENS/BTM button 8, 9, 13

ql OFF button* 6

* Warning when installing in a car

without ACC (accessory) position on

the ignition key switch

Be sure to press (OFF) on the unit for 2

seconds to turn off the clock display after

turning off the engine.

When you press (OFF) momentarily, the

clock display does not turn off and this

causes battery wear.

XR-CA370X/CA370

SOURCE

MODE

SEL

RELEASE

EQ3

DSPL

DISC

REP

SHUF

ATA

OFFSENS

BTM

SEEK

DIR

AF ATT

123456

TAPTY

66

Attaching the front panel

Attach part A of the front panel to part B of

the unit as illustrated and push the left side

into position until it clicks.

Notes

• Be sure not to attach the front panel upside

down.

• Do not press the front panel too hard against the

unit when attaching it.

• Do not press too hard or put excessive pressure

on the display window of the front panel.

• Do not expose the front panel to direct sunlight

or heat sources such as hot air ducts, and do not

leave it in a humid place. Never leave it on the

dashboard of a car parked in direct sunlight or

where there may be a considerable rise in

temperature.

Caution alarm

If you turn the car ignition off without

removing the front panel, the caution alarm

will beep for a few seconds.

If you connect an optional power amplifier and

do not use the built-in amplifier, the beep

sound will be deactivated.

Getting Started

Resetting the unit

Before operating the unit for the first time, or

after replacing the car battery or changing the

connections, you must reset the unit.

Remove the front panel and press the RESET

button with a pointed object, such as a

ballpoint pen.

Note

Pressing the RESET button will erase the clock

setting and some memorized functions.

Detaching the front panel

You can detach the front panel of this unit to

protect the unit from being stolen.

1 Press (OFF).

2 Press (RELEASE), then slide the front

panel a little to the left, and pull it off

towards you.

Notes

• Be sure not to drop the panel when detaching it

from the unit.

• If you detach the panel while the unit is still

turned on, the power will turn off automatically

to prevent the speakers from being damaged.

• When carrying the front panel with you, use the

supplied front panel case.

RESET button

(OFF)

(RELEASE)

A

B

77

Cassette Player

Listening to a tape

Insert a cassette.

Playback starts automatically.

The side facing up is played.

The side facing down is played.

Tip

To change the tape‘s playback direction, press m

and M.

To stop playback and eject the

cassette

Press Z.

Fast-winding the tape

During playback, press m or M.

* The indicator will flash while fast-winding the

tape.

To start playback during fast-forwarding or

rewinding, press the other fast-winding button

partially until the locked button is released.

To rewind

m

M

Direction

indicator*

FWD

REV

To advance

M

m

to go forward

to go back

to go forward

to go back

Setting the clock

The clock uses a 24-hour digital indication.

Example: To set the clock to 10:08

1 Press (DSPL) for 2 seconds.

The hour indication flashes.

1 Press either side of the volume button

to set the hour.

2 Press (SEL).

The minute indication flashes.

3 Press either side of the volume button

to set the minute.

2 Press (DSPL).

The clock starts.

After the clock setting is complete, the

display returns to normal play mode.

Tip

You can set the clock automatically with the RDS

feature (page 14).

88

Radio

Storing stations

automatically

— Best Tuning Memory (BTM)

The unit selects the stations with the strongest

signals and stores them in the order of their

frequencies. You can store up to 6 stations on

each band (FM1, FM2, FM3, MW, and LW).

Caution

When tuning in stations while driving, use

Best Tuning Memory to prevent accidents.

1 Press (SOURCE) repeatedly to select the

radio.

In case of tape playback, press Z to eject the

tape.

Each time you press (SOURCE), the source

changes as follows:

Radio t CD* t MD*

* If the corresponding optional equipment is

not connected, this item will not appear.

2 Press (MODE) repeatedly to select the

band.

Each time you press (MODE), the band

changes as follows:

FM1 t FM2 t FM3 t MW t LW

3 Press (SENS) (BTM) for 2 seconds.

The unit stores stations in the order of their

frequencies on the number buttons.

A beep sounds when the setting is stored.

Notes

• The unit does not store stations with weak

signals. If only a few stations can be received,

some number buttons will retain their former

setting.

• When a number is indicated in the display, the

unit starts storing stations from the one currently

displayed.

Radio reception during

fast-forwarding or

rewinding of a tape

— Automatic Tuner Activation (ATA)

When fast-forwarding or rewinding with the

m or M button, the radio will turn on

automatically.

During playback, press (PTY) (ATA)

repeatedly until “ATA-ON” in the display

appears.

ATA-ON y ATA-OFF

ATA mode starts.

To return to normal play mode, select “ATA-

OFF.”

99

Storing only the desired

stations

You can preset up to 18 FM stations (6 each for

FM1, 2, and 3), up to 6 MW stations, and up to

6 LW stations in the order of your choice.

1 Press (SOURCE) repeatedly to select the

radio.

In case of tape playback, press Z to eject the

tape.

2 Press (MODE) repeatedly to select the

band.

3 Press either side of (SEEK) to tune in the

station that you want to store on the

number button.

4 Press the desired number button ((1) to

(6)) until “MEM” appears.

The number button indication appears in

the display.

Note

If you try to store another station on the same

number button, the previously stored station will

be erased.

Receiving the stored

stations

1 Press (SOURCE) repeatedly to select the

radio.

In case of tape playback, press Z to eject the

tape.

2 Press (MODE) repeatedly to select the

band.

3 Press the number button ((1) to (6)) on

which the desired station is stored.

If you cannot tune in a preset

station

— Automatic tuning/ Local Seek Mode

Automatic tuning:

Press either side of (SEEK) to search for

the station.

Scanning stops when the unit receives a

station. Press either side of (SEEK)

repeatedly until the desired station is

received.

Local Seek Mode:

If the automatic tuning stops too

frequently, press (SENS) repeatedly until

“LOCAL-ON” appears.

Only the stations with relatively strong

signals will be tuned in.

Tip

If you know the frequency of the station you want

to listen to, press either side of (SEEK) until the

desired frequency appears (manual tuning).

If FM stereo reception is poor

— Monaural Mode

During radio reception, press (SENS)

repeatedly until “MONO-ON” appears.

“MONO” indicator is displayed.

The sound improves, but becomes

monaural (“ST” disappears).

To return to normal radio reception mode,

select “MONO-OFF.”

“LCL” indicator is displayed.

10

RDS

Overview of the RDS

function

Radio Data System (RDS) is a broadcasting

service that allows FM stations to send

additional digital information along with the

regular radio programme signal. Your car

stereo offers you a variety of services. Here are

just a few: retuning the same programme

automatically, listening to traffic

announcements, and locating a station by

programme type.

Notes

• Depending on the country or region, not all of

the RDS functions are available.

• RDS may not work properly if the signal strength

is weak or if the station you are tuned to is not

transmitting RDS data.

Displaying the station

name

The name of the current station lights up in the

display.

Select an FM station (page 8).

When you tune in an FM station that

transmits RDS data, the station name

appears in the display.

Note

The “*” indication means that an RDS station is

being received.

Changing the display item

Each time you press (DSPL), the item changes

as follows:

Station Name* (Frequency) y Clock

* When you tune in an FM station that transmits

RDS data, the station name appears.

Note

“NO NAME” appears if the received station does

not transmit RDS data.

Retuning the same

programme automatically

— Alternative Frequencies (AF)

The Alternative Frequencies (AF) function

automatically selects and retunes the station

with the strongest signal in a network. By

using this function, you can continuously

listen to the same programme during a long-

distance drive without having to retune the

station manually.

1 Select an FM station (page 8).

2 Press (AF) repeatedly until “AF-ON”

appears.

The unit starts searching for an alternative

station with a stronger signal in the same

network.

Note

When there is no alternative station in the area

and you do not need to search for an alternative

station, turn the AF function off by pressing (AF)

repeatedly until “AF-OFF” appears.

102.5MHz

96.0MHz

Frequencies change automatically.

Station

98.5MHz

11

Changing the display item

Each time you press (AF), the item changes as

follows:

AF-ON y AF-OFF

Notes

• When “NO AF” and the station name flash

alternately, it means that the unit cannot find an

alternative station in the network.

• If the station name starts flashing after selecting

a station with the AF function on, this indicates

that no alternative frequency is available. Press

either side of (SEEK) while the station name is

flashing (within 8 seconds). The unit starts

searching for another frequency with the same PI

(Programme Identification) data (“PI SEEK”

appears and no sound is heard). If the unit

cannot find another frequency, “NO PI” appears,

and the unit returns to the previously selected

frequency.

Listening to a regional programme

The “REG-ON” (regional on) function lets you

stay tuned to a regional programme without

being switched to another regional station.

(Note that you must turn the AF function on.)

The unit is factory preset to “REG-ON,” but if

you want to turn off the function, do the

following.

During radio reception, press (AF) for 2

seconds until “REG-OFF” appears.

Note that selecting “REG-OFF” might cause

the unit to switch to another regional

station within the same network.

To return to regional on, select “REG-ON.”

Note

This function does not work in the United

Kingdom and in some other areas.

Changing the display item

Each time you press (AF) for 2 seconds, the

item changes as follows:

REG-ON y REG-OFF

Local link function

(United Kingdom only)

The Local Link function lets you select other

local stations in the area, even if they are not

stored on your number buttons.

1 Press a number button that has a local

station stored on it.

2 Within 5 seconds, press the number

button of the local station again.

3 Repeat this procedure until the desired

local station is received.

12

Presetting the volume of traffic

announcements

You can preset the volume level of the traffic

announcements beforehand so you won’t

miss the announcement. When a traffic

announcement starts, the volume will be

automatically adjusted to the preset level.

1 Press the volume button to adjust the

desired volume level.

2 Press (TA) for 2 seconds.

“TA” appears and the setting is stored.

Receiving emergency

announcements

If an emergency announcement comes in while

you are listening to the radio, the programme

will automatically switch to it. If you are

listening to a source other than the radio, the

emergency announcements will be heard if

you set AF or TA to ON. The unit will then

automatically switch to these announcements

no matter which source you are listening to at

the time.

Listening to traffic

announcements

The Traffic Announcement (TA) and Traffic

Programme (TP) data let you automatically

tune in an FM station that is broadcasting

traffic announcements even if you are listening

to other programme sources.

Press (TA) repeatedly until “TA-ON”

appears.

The unit starts searching for traffic

information stations. “TP” appears in the

display when the unit finds a station

broadcasting traffic announcements.

When the traffic announcement starts,

“TA” flashes. The flashing stops when the

traffic announcement is over.

Tip

If the traffic announcement starts while you are

listening to another programme source, the unit

automatically switches to the announcement and

goes back to the original source when the

announcement is over.

Notes

•

“NO TP” flashes for 5 seconds if the received

station does not broadcast traffic announcements.

Then, the unit starts searching for a station that

broadcasts it.

• When “EON” appears with “TP” in the display,

the current station makes use of broadcast traffic

announcements by other stations in the same

network.

To cancel the current traffic

announcement

Press (TA).

To cancel all traffic announcements, turn off

the function by pressing (TA) until

“TA-OFF” appears.

13

Presetting the RDS

stations with the AF and

TA data

When you preset RDS stations, the unit stores

each station’s data as well as its frequency, so

you don’t have to turn on the AF or TA

function every time you tune in the preset

station. You can select a different setting (AF,

TA, or both) for individual preset stations, or

the same setting for all preset stations.

Presetting the same setting for all

preset stations

1 Select an FM band (page 8).

2 Press (AF) and/or (TA) to select “AF-ON”

and/or “TA-ON.”

Note that selecting “AF-OFF” or “TA-OFF”

stores not only RDS stations, but also non-

RDS stations.

3 Press (SENS) (BTM) until “BTM” flashes.

Presetting different settings for

each preset station

1 Select an FM band, and tune in the

desired station.

2 Press (AF) and/or (TA) to select “AF-ON”

and/or “TA-ON.”

3 Press the desired number button until

“MEM” appears.

Repeat from step 1 to preset other stations.

Tip

If you want to change the preset AF and/or TA

setting after you tune in the preset station, you

can do so by turning the AF or TA function on or

off.

Locating a station by

programme type

You can locate the station you want by

selecting one of the programme types shown

below.

Programme types Display

News NEWS

Current Affairs AFFAIRS

Information INFO

Sports SPORT

Education EDUCATE

Drama DRAMA

Culture CULTURE

Science SCIENCE

Varied VARIED

Popular Music POP M

Rock Music ROCK M

Easy Listening EASY M

Light Classical LIGHT M

Classical CLASSICS

Other Music Type OTHER M

Weather WEATHER

Finance FINANCE

Children’s Programmes CHILDREN

Social Affairs SOCIAL A

Religion RELIGION

Phone In PHONE IN

Travel TRAVEL

Leisure LEISURE

Jazz Music JAZZ

Country Music COUNTRY

National Music NATION M

Oldies Music OLDIES

Folk Music FOLK M

Documentary DOCUMENT

Not specified NONE

Note

You cannot use this function in some countries

where no PTY (Programme Type selection) data is

available.

continue to next page t

14

Setting the clock

automatically

The CT (Clock Time) data from the RDS

transmission sets the clock automatically.

1 During radio reception, press (SEL) and

(2) simultaneously.

2 Press (2) repeatedly until “CT-ON”

appears.

The clock is set.

In 2 seconds the normal display

automatically appears.

To cancel the CT function

Select “CT-OFF” in step 2.

Notes

• The CT function may not work even though an

RDS station is being received.

• There might be a difference between the time

set by the CT function and the actual time.

1 Press (PTY) during FM reception.

The current programme type name appears

if the station is transmitting the PTY data.

“- - - - -” appears if the received station is

not an RDS station, or if the RDS data has

not been received.

If the TA function is ON, the unit starts

searching for the next station.

2 Press (PTY) repeatedly until the desired

programme type appears.

The programme types appear in the order

shown in the above table. Note that you

cannot select “NONE” (Not specified) for

searching.

3 Press either side of (SEEK).

The unit starts searching for a station

broadcasting the selected programme type.

When the unit finds the programme, the

programme type appears again for 5

seconds.

“NO” and the programme type appear

alternately for 5 seconds if the unit cannot

find the programme type. It then returns to

the previously selected station.

15

GB

Other Functions

Adjusting the balance and

fader

You can adjust the balance and fader.

1 Press (SEL) repeatedly until “BAL” or

“FAD” appears.

Each time you press (SEL), the item

changes as follows:

LOW* t MID* t HIGH* t

BAL (left-right) t FAD (front-rear)

* When EQ3 is activated (page 16).

2 Press either side of the volume button to

adjust the selected item.

Adjust within 3 seconds after selecting the

item.

Attenuating the sound

Press (ATT).

After “ATT-ON” momentarily flashes, the

“ATT” indication appears in the display.

To restore the previous volume level, press

(ATT) again.

“ATT-OFF” flashes momentarily.

Changing the sound and

display settings

The following items can be set:

•CT (Clock Time) (page 14).

•A.SCRL (Auto Scroll)* (page 17).

•M.DSPL (Motion Display)

– the demonstration mode which appears

when the tape is ejected and no source is

selected (e.g., tuner is turned off).

•BEEP – to turn the beep sound on or off.

1 Press (SEL) and the desired preset

number button simultaneously.

(SEL) + (2): CT

(SEL) + (3): A.SCRL*

(SEL) + (4): M.DSPL

(SEL) + (6): BEEP

* When no CD or MD is playing, this item will

not appear.

Note

The displayed item will differ depending on the

source.

2 Press (SEL) and the preset number

button repeatedly to select the desired

setting (Example: ON or OFF).

16

Setting the equalizer

— EQ3

You can select an equalizer curve for 7 music

types (XPLOD, VOCAL, CLUB, JAZZ, NEW

AGE, ROCK, CUSTOM, and OFF (equalizer

OFF)).

You can store a different equalizer setting for

each source.

Selecting the equalizer curve

1 Press (SOURCE) to select a source

(Radio, CD or MD) or insert a cassette.

2 Press (EQ3) repeatedly to select the

desired equalizer curve.

Each time you press (EQ3), the item

changes.

To cancel the equalizing effect, select

“OFF.”

Adjusting the equalizer curve

You can store and adjust the equalizer settings

for different tone ranges.

1 Press (SOURCE) to select a source (Radio,

CD or MD) or insert a cassette.

2 Press (EQ3) repeatedly to select the

desired equalizer curve.

3 Adjusting the equalizer curve.

1 Press (SEL) repeatedly to select the

desired tone range.

Each time you press (SEL), the tone

range changes.

LOW t MID t HI (t BAL t FAD)

2 Press either side of the volume button

repeatedly to adjust to the desired

volume level.

The volume level is adjustable by 1 dB

steps from –10 dB to +10 dB.

3 Repeat step 1 and 2 to adjust the

equalizer curve.

To restore the factory-set equalizer

curve, press (SEL) for 2 seconds.

After 3 seconds, the display returns to

normal play mode.

Note

When EQ3 is set to “OFF,” you cannot adjust the

equalizer settings.

17

GB

With Optional Equipment

CD/MD Unit

This unit can control external CD/MD units.

If you connect an optional CD unit with the

CD TEXT function, the CD TEXT information

will appear in the display when you play a CD

TEXT disc.

Playing a CD or MD

1 Press (SOURCE) repeatedly to select CD

or MD.

In case of tape playback, press Z to eject the

tape.

2 Press (MODE) until the desired unit

appears.

CD/MD playback starts.

When a CD/MD unit is connected, all the

tracks play from the beginning.

Tip

With the optional MG Memory Stick System-up

Player MGS-X1 connected to this unit, press

(SOURCE) to select “MD,” then press (MODE) to

select the unit number of the MD (MD1 or MD2,

etc.).

Changing the display item

Each time you press (DSPL) during CD, CD

TEXT, or MD playback, the item changes as

follows:

Elapsed playback time t

Disc name*

1

/Artist name*

2

t Track name*

3

t

Clock

*

1

If you have not labelled the disc or if there is no

disc name prerecorded on the MD, “NO NAME”

appears in the display.

*

2

If you play a CD TEXT disc, the artist name

appears in the display after the disc name. (Only

for CD TEXT discs with the artist name.)

*

3

If the track name of a CD TEXT disc or MD is not

prerecorded, “NO NAME” appears in the

display.

Automatically scrolling a display

item — Auto Scroll

If the disc name, artist name, or track name on

a CD TEXT disc or MD exceeds 8 characters

and the Auto Scroll function is on, information

automatically scrolls across the display as

follows:

• The disc name appears when the disc has

changed (if the disc name is selected).

• The track name appears when the track has

changed (if the track name is selected).

If you press (DSPL) to change the display

item, the disc or track name of the CD TEXT or

MD disc is scrolled automatically whether you

set the function ON or OFF.

During playback, press (SEL) and (3) to

select “A.SCRL-ON.”

To cancel Auto Scroll, select “A.SCRL-OFF.”

Note

For some discs with very many characters, the

following cases may happen:

— Some of the characters are not displayed.

— Auto Scroll does not work.

continue to next page t

18

Playing tracks repeatedly

— Repeat Play

You can select:

•REP-TRACK – to repeat a track.

•REP-DISC – to repeat a disc.

During playback, press (3) (REP)

repeatedly until the desired setting

appears.

REP-TRACK t REP-DISC t REP-OFF

Repeat Play starts.

To return to normal play mode, select “REP-

OFF.”

Playing tracks in random

order — Shuffle Play

You can select:

•SHUF-DISC – to play the tracks on the

current disc in random order.

•SHUF-CHGR – to play the tracks in the

current unit in random order.

•SHUF-ALL* – to play all the tracks in all the

units in random order.

During playback, press (4) (SHUF)

repeatedly until the desired setting

appears.

SHUF-DISCt SHUF-CHGR t SHUF-ALL*

t SHUF-OFF

Shuffle Play starts.

* “SHUF-ALL” is only available when you

connect two or more optinal CD/MD units.

To return to normal play mode, select “SHUF-

OFF.”

Locating a specific track

— Automatic Music Sensor (AMS)

During playback, press either side of

(SEEK) momentarily for each track you

want to skip.

Locating a specific point in a track

— Manual Search

During playback, press and hold either

side of (SEEK). Release when you have

found the desired point.

Switching to other discs

During playback, press (1) (DISC –) or

(2) (DISC +) button.

The desired disc in the current unit begins

playback.

(1) (DISC –): For preceding discs

(2) (DISC +): For succeeding discs

To locate succeeding tracks

To locate preceding tracks

To search forward

To search backward

Disc number

Track number

SEEK

19

Fuse (10 A)

Additional

Information

Maintenance

Fuse replacement

When replacing the fuse, be sure to use one

matching the amperage rating stated on the

original fuse. If the fuse blows, check the

power connection and replace the fuse. If the

fuse blows again after replacement, there may

be an internal malfunction. In such a case,

consult your nearest Sony dealer.

Warning

Never use a fuse with an amperage rating

exceeding the one supplied with the unit as

this could damage the unit.

Cleaning the connectors

The unit may not function properly if the

connectors between the unit and the front

panel are not clean. In order to prevent this,

open the front panel by pressing (RELEASE),

then detach it and clean the connectors with a

cotton swab dipped in alcohol. Do not apply

too much force. Otherwise, the connectors may

be damaged.

Main unit

Back of the front panel

Notes

• For safety, turn off the engine before cleaning

the connectors and remove the key from the

ignition switch.

• Never touch the connectors directly with your

fingers or any metal device.

20

Face the hook

inwards.

Orient the release

key correctly.

Removing the unit

1 Remove the protection collar.

1 Detach the front panel (page 6).

2 Engage the release keys together

with the protection collar.

3 Pull out the release keys to remove

the protection collar.

2 Remove the unit.

1 Insert both release keys together until

they click.

2 Pull the release keys to unseat the

unit.

3 Slide the unit out of the mounting.

La page est en cours de chargement...

Sony XR-CA370X Manuel utilisateur

Ce manuel convient également à

Sony XR-CA370X Manuel utilisateur

dans d''autres langues

Documents connexes