FEIN WSG7-115 Manuel utilisateur

FEIN Service

USA

FEIN Power Tools Inc.

1000 Omega Drive

Suite 1180

Pittsburgh, PA 15205

Telephone: (412) 922-8886

Toll Free: 1-800-441-9878

www.feinus.com

Canada

FEIN Canadian Power Tool

Company

323 Traders Boulevard East

Mississauga, Ontario L4Z 2E5

Telephone.: (905) 8901390

Toll Free: 1-800-265-2581

FEIN Canadian Power Tool

Company

2810 De Miniac

St. Laurent, Quebec H4S 1K9

Telephone: (514) 331-7390

Toll Free: 1-800-789-8181

www.fein.com

Headquarter

C. & E. Fein GmbH

Hans-Fein-Straße 81

D-73529 Schwäbisch Gmünd-Bargau

www.fein.com

 WSG7-115 7 221 97

OBJ_DOKU-0000004800-004.fm Page 1 Wednesday, March 9, 2016 11:45 AM

2

Instruction Manual

Mode d'emploi

Instrucciones de uso

en

3

fr

23

es

45

OBJ_BUCH-0000000194-003.book Page 2 Friday, December 11, 2015 12:00 PM

3

en

For your safety.

Read all safety warnings and

all instructions. Failure to fol-

low the warnings and instructions may result

in electric shock, fire and/or serious injury.

Save all warnings and instructions for future-

reference.

Do not use this power tool before you

have thoroughly read and completely

understood this Instruction Manual, including

the figures, specifications, safety regulations

and the signs indicating DANGER, WARN-

ING and CAUTION.

Only carry out such operations with this

power tool as intended for by FEIN. Only use

application tools and accessories that have

been released by FEIN.

Please also observe the relevant national

industrial safety regulations.

Non-observance of the safety instructions in

the said documentation can lead to an electric

shock, burns and/or severe injuries.

This Instruction Manual should be kept for

later use and enclosed with the power tool,

should it be passed on or sold.

SAVE THESE INSTRUCTIONS.

The term “power tool” in the warnings refers

to your mains-operated (corded) power tool

or battery operated (cordless) power tool.

General safety rules.

1) Work area safety

a)Keep work area clean and well lit. Clut-

tered or dark areas invite accidents.

b)Do not operate power tools in explosive

atmospheres, such as in the presence of

flammable liquids, gases or dust. Power

tools create sparks which may ignite the

dust or fumes.

c) Keep children and bystanders away

while operating a power tool. Distrac-

tion can cause you to lose control.

2) Electrical safety

a)Power tool plugs must match the outlet.

Never modify the plug in any way. Do not

use any adapter plugs with earthed

(grounded) power tools. Unmodified

plugs and matching outlets will reduce

risk of electric shock.

b)Avoid body contact with earthed or

grounded surfaces such as pipes, radia-

tors, ranges and refrigerators. There is

an increased risk of electric shock if

your body is earthed or grounded.

c) Do not expose power tools to rain or wet

conditions. Water entering a power tool

will increase the risk of electric shock.

d)Do not abuse the cord. Never use the

cord for carrying, pulling or unplugging

the power tool. Keep cord away from

heat, oil, sharp edges or moving parts.

Damaged or entangled cords increase

the risk of electric shock.

e) When operating a power tool outdoors,

use an extension cord suitable for outdoor

use. Use of a cord suitable for outdoor

use reduces the risk of electric shock.

f) If operating a power tool in a damp loca-

tion is unavoidable, use a ground fault

circuit interrupter (GFCI) protected sup-

ply. Use of an GFCI reduces the risk of

electric shock.

3) Personal safety

a) Stay alert, watch what you are doing and

use common sense when operating a

power tool. Do not use a power tool while

you are tired or under the influence of

drugs, alcohol or medication. A moment

of inattention while operating power

tools may result in serious personal injury.

b)Use personal protective equipment.

Always wear eye protection. Protective

equipment such as dust mask, non-skid

safety shoes, hard hat, or hearing pro-

tection used for appropriate conditions

will reduce personal injuries.

c) Prevent unintentional starting. Ensure

the switch is in the off-position before

connecting to power source and/or bat-

tery pack, picking up or carrying the

tool. Carrying power tools with your

finger on the switch or energising

power tools that have the switch on

invites accidents.

WARNING

OBJ_BUCH-0000000194-003.book Page 3 Friday, December 11, 2015 12:00 PM

4

en

d)Remove any adjusting key or wrench

before turning the power tool on. A

wrench or a key left attached to a rotat-

ing part of the power tool may result in

personal injury.

e) Do not overreach. Keep proper footing

and balance at all times. This enables

better control of the power tool in

unexpected situations.

f) Dress properly. Do not wear loose cloth-

ing or jewelery. Keep your hair, clothing

and gloves away from moving parts.

Loose clothes, jewelry or long hair can

be caught in moving parts.

g)If devices are provided for the connec-

tion of dust extraction and collection

facilities, ensure these are connected

and properly used. Use of dust collec-

tion can reduce dust-related hazards.

4) Power tool use and care

a)Do not force the power tool. Use the cor-

rect power tool for your application. The

correct power tool will do the job bet-

ter and safer at the rate for which it was

designed.

b) Do not use the power tool if the switch

does not turn it on and off. Any power

tool that cannot be controlled with the

switch is dangerous and must be repaired.

c) Disconnect the plug from the power

source and/or the battery pack from the

power tool before making any adjust-

ments, changing accessories, or storing

power tools. Such preventive safety

measures reduce the risk of starting the

power tool accidentally.

d)Store idle power tools out of the reach of

children and do not allow persons unfa-

miliar with the power tool or these

instructions to operate the power tool.

Power tools are dangerous in the hands

of untrained users.

e) Maintain power tools. Check for misalign-

ment or binding of moving parts, break-

age of parts and any other condition that

may affect the power tool’s operation. If

damaged, have the power tool repaired

before use. Many accidents are caused by

poorly maintained power tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with

sharp cutting edges are less likely to

bind and are easier to control.

g) Use the power tool, accessories and tool

bits etc. in accordance with these

instructions, taking into account the

working conditions and the work to be

performed. Use of the power tool for

operations different from those intended

could result in a hazardous situation.

5) Service

a)Have your power tool serviced by a qual-

ified repair person using only identical

replacement parts. This will ensure that

the safety of the power tool is main-

tained.

Special safety instructions.

Safety Warnings common for Grind-

ing, Sanding, Wire Brushing or Abra-

sive Cutting Off Operations

This power tool is intended to function as a

grinder, sander, wire brush or cut-off tool.

Read all safety warnings, instructions, illus-

trations and specifications provided with this

power tool. Failure to follow all instructions

listed below may result in electric shock, fire

and/or serious injury.

Operations such as polishing are not recom-

mended to be performed with this power tool.

Operations for which the power tool was not

designed may create a hazard and cause per-

sonal injury.

Do not use accessories which are not specifi-

cally designed and recommended by the tool

manufacturer. Just because the accessory can

be attached to your power tool, it does not

assure safe operation.

OBJ_BUCH-0000000194-003.book Page 4 Friday, December 11, 2015 12:00 PM

5

en

The rated speed of the accessory must be at

least equal to the maximum speed marked on

the power tool. Accessories running faster

than their rated speed can break and fly apart.

The outside diameter and the thickness of

your accessory must be within the capacity

rating of your power tool. Incorrectly sized

accessories cannot be adequately guarded or

controlled.

Application tools with threaded insert must

exactly fit the thread size of the spindle. For

application tools mounted by flanges, the

arbor hole of the application tool must fit the

mounting hole diameter of the flange. Appli-

cation tools that are not precisely mounted to

the power tool will run out of balance, vibrate

excessively and may cause loss of control.

Do not use a damaged accessory. Before each

use inspect the accessory such as abrasive

wheels for chips and cracks, backing pad for

cracks, tear or excess wear, wire brush for

loose or cracked wires. If power tool or acces-

sory is dropped, inspect for damage or install

an undamaged accessory. After inspecting

and installing an accessory, position yourself

and bystanders away from the plane of the

rotating accessory and run the power tool at

maximum no-load speed for one minute.

Damaged accessories will normally break

apart during this testtime.

Wear personal protective equipment. Depend-

ing on application, use face shield, safety

goggles or safety glasses. Where appropriate,

wear dust mask, hearing protectors, gloves

and workshop apron capable of stopping

small abrasive or workpiece fragments. The

safety glasses must be capable of protecting

against flying particles generated by the vari-

ous operations. Prolonged exposure to high

intensity noise may cause loss of hearing.

Keep bystanders a safe distance away from

work area. Anyone entering the work area

must wear personal protective equipment.

Fragments of workpiece or of a broken acces-

sory may fly away and cause injury beyond

immediate area of operation.

Hold the power tool by insulated gripping sur-

faces only, when performing an operation

where the cutting accessory may contact hid-

den wiring or its own cord. Cutting accessory

contacting a “live” wire may make exposed

metal parts of the power tool “live” and could

give the operator an electric shock.

Position the cord clear of the spinning acces-

sory. If you lose control of the power tool,

the cord may be cut or snagged and your hand

or arm may be pulled into the spinning acces-

sory.

Never lay the power tool down until the acces-

sory has come to a complete stop. The spin-

ning accessory may grab the surface and pull

the power tool out of your control.

Do not run the power tool while carrying it at

your side. Accidental contact with the spin-

ning accessory could snag your clothing, pull-

ing the accessory into your body.

Regularly clean the power tool’s air vents.

The motor’s fan will draw the dust inside the

housing and excessive accumulation of pow-

dered metal may cause electrical hazards.

Do not operate the power tool near flammable

materials. Sparks could ignite these materials.

Do not use accessories that require liquid

coolants. Using water or other liquid coolants

may result in electrocution or shock.

Kickback and related warnings

Kickback is a sudden reaction to a pinched or

snagged rotating wheel, backing pad, brush or

any other accessory. Pinching or snagging

causes rapid stalling of the rotating accessory

which in turn causes the uncontrolledpower

tool to be forced in the direction opposite of

the accessory’s rotation at the point of the

binding.

For example, if an abrasive wheel is snagged

or pinched by the workpiece, the edge of the

wheel that is entering into the pinch point can

dig into the surface of the material causing the

wheel to climb out or kick out. The wheel

may either jump toward or away from the

operator, depending on direction of the

wheel’s movement at the point of pinching.

Abrasive wheels may also break under these

conditions.

OBJ_BUCH-0000000194-003.book Page 5 Friday, December 11, 2015 12:00 PM

6

en

Kickback is the result of power tool misuse

and/or incorrect operating procedures or

conditions and can be avoided by taking

proper precautions as given below.

Maintain a firm grip on the power tool and posi-

tion your body and arm to allow you to resist

kickback forces. Always use auxiliary handle, if

provided, for maximum control over kickback

or torque reaction during start-up. The opera-

tor can control torque reactions or kickback

forces, if proper precautions are taken.

Never place your hand near the rotating

accessory. Accessory may kickback over

your hand.

Do not position your body in the area where

power tool will move if kickback occurs. Kick-

back will propel the tool in direction opposite

to the wheel’s movement at the point of snag-

ging.

Use special care when working corners, sharp

edges, etc. Avoid bouncing and snagging the

accessory. Corners, sharp edges or bouncing

have a tendency to snag the rotating accessory

and cause loss of control or kickback.

Do not attach a saw chain woodcarving blade

or toothed saw blade. Such blades create fre-

quent kickback and loss of control over the

power tool.

Safety warnings specific for grinding

and abrasive cutting-off operations

Use only wheel types that are recommended

for your power tool and the specific guard

designed for the selected wheel. Wheels for

which the power tool was not designed can-

not be adequately guarded and are unsafe.

The grinding surface of the centre depressed

wheels must be mounted below the plane of

the guard lip. An improperly mounted wheel

that projects through the plane of the guard

lip cannot be adequately protected.

The guard must be securely attached to the

power tool and positioned for maximum

safety, so the least amount of wheel is

exposed towards the operator. The guard

helps to protect operator from broken wheel

fragments, accidental contact with wheel and

sparks that could ignite clothing.

Wheels must be used only for recommended

applications. For example: do not grind with

the side of the cut-off wheel. Abrasive cut-off

wheels are intended for peripheral grinding;

side forces applied to these wheels may cause

them to shatter.

Always use undamaged wheel flanges that

are of correct size and shape for your selected

wheel. Proper wheel flanges support the

wheel thus reducing the possibility of wheel

breakage. Flanges for cut-off wheels may be

different from grinding wheel flanges.

Do not use worn down wheels from larger

power tools. Wheels intended for larger

power tools are not suitable for the higher

speed of a smaller tool and may burst.

Additional safety warnings specific

for abrasive cutting off operations

Do not “jam” the cut-off wheel or apply exces-

sive pressure. Do not attempt to make an exces-

sive depth of cut. Overstressing the wheel

increases the loading and susceptibility to twist-

ing or binding of the wheel in the cut and the

possibility of kickback or wheel breakage.

Do not position your body in line with and

behind the rotating wheel. When the wheel,

at the point of operation, is moving away

from your body, the possible kickback may

propel the spinning wheel and the power tool

directly at you.

When wheel is binding or when interrupting a

cut for any reason, switch off the power tool

and hold the power tool motionless until the

wheel comes to a complete stop. Never

attempt to remove the cut-off wheel from the

cut while the wheel is in motion otherwise

kickback may occur. Investigate and take cor-

rective action to eliminate the cause of wheel

binding.

Do not restart the cutting operation in the

workpiece. Let the wheel reach full speed and

carefully re-enter the cut. The wheel may

bind, walk up or kickback if the power tool is

restarted in the workpiece.

Support panels or any oversized workpiece to

minimize the risk of wheel pinching and kick-

back. Large workpieces tend to sag under

their own weight. Supports must be placed

under the workpiece near the line of cut and

near the edge of the workpiece on both sides

of the wheel.

OBJ_BUCH-0000000194-003.book Page 6 Friday, December 11, 2015 12:00 PM

7

en

Use extra caution when making a “pocket

cut” into existing walls or other blind areas.

The protruding wheel may cut gas or water

pipes, electrical wiring or objects that can

cause kickback.

Safety warnings specific for sanding

operations

Do not use excessively oversized sanding disc

paper. Follow manufacturers recommenda-

tions, when selecting sanding paper. Larger

sanding paper extending beyond the sanding

pad presents a laceration hazard and may

cause snagging, tearing of the disc, or kick-

back.

Safety warnings specific for wire

brushing operations

Be aware that wire bristles are thrown by the

brush even during ordinary operation. Do not

overstress the wires by applying excessive

load to the brush. The wire bristles can easily

penetrate light clothing and/or skin.

If the use of a guard is recommended for wire

brushing, do not allow any interference of the

wire wheel or brush with the guard. Wire

wheel or brush may expand in diameter due

to work load and centrifugal forces.

Further safety warnings

Use elastic spacers/liners when these are

provided with the grinding accessory.

Make sure that the application tools are

mounted in accordance with the manufactur-

ers instructions. The mounted application

tools must be able to rotate freely. Incorrectly

mounted application tools can become loose

during operation and be thrown from the

machine.

Handle grinding accessories carefully and

store them according to the manufacturer’s

instructions. Damaged grinding accessories can

develop cracks and burst during operation.

When using application tools with a threaded

insert, take care that the thread in the applica-

tion tool is long enough to hold the spindle

length of the power tool. The thread in the

application tool must match the thread on the

spindle. Incorrectly mounted application tools

can loosen during operation and cause injuries.

Do not direct the power tool against yourself,

other persons or animals. Danger of injury

from sharp or hot application tools.

Beware of any concealed electric cables, gas

or water conduits. Check the working area

before commencing work, e. g. with a metal

detector.

Use a stationary extraction system, blow out

ventilation slots frequently and connect a

residual current device (RCD) on the line side.

When working metal under extreme operat-

ing conditions, it is possible for conductive

dust to settle in the interior of the power

tool. The total insulation of the power tool

can be impaired.

This double-insulated power tool is equipped

with a polarized plug (one contact is wider

than the other). The plug will only fit into the

polarized socket outlet in one position. Turn

the plug if it does not fit completely into the

socket outlet. If the plug still does not fit, have

a qualified electrician install a polarized

socket outlet. Do not modify or alter the plug

under any circumstances. Double-insulated

power tools neither require a three-core

mains cable nor a mains connection with

ground contact.

Operate the power tool only off power sup-

plies whose voltage and frequency values

correspond with the values on the type plate

of the power tool.

If operating the power tool in a damp location,

it must be connected via a ground-fault cir-

cuit interrupter (GFCI). Using special rubber

protective gloves and footwear increase your

own safety.

NOTE: Such a device is also known as ground

fault circuit interrupter (GFCI) or earth leak-

age circuit breaker (ELCB).

Do not rivet or screw any name-plates or

signs onto the power tool. If the insulation is

damaged, protection against an electric shock

will be ineffective. Adhesive labels are recom-

mended.

Always work with the auxiliary handle. The

auxiliary handle ensures reliable guiding of

the power tool.

Before putting into operation, check the

power connection and the power plug for

damage.

Recommendation: The tool should always be

supplied with power via a ground fault circuit

interrupter (GFCI) with a rated current of

30 mA or less.

OBJ_BUCH-0000000194-003.book Page 7 Friday, December 11, 2015 12:00 PM

8

en

Handling hazardous dusts.

When working with power

tools, such as when grinding,

sanding, polishing, sawing or for other work

procedures where material is removed, dusts

develop that are both hazardous to one’s

health and can spontaneously combust or be

explosive.

Contact with or inhaling some dust types can

trigger allergic reactions to the operator or

bystanders and/or lead to respiratory infec-

tions, cancer, birth defects or other reproduc-

tive harm.

Examples of such materials which contain

chemicals that can produce hazardous dusts,

are:

– Asbestos and materials containing asbestos;

– Lead-containing coatings, some wood

types such as beech and oak;

– Minerals and metal;

– Silicate particles from bricks, concrete and

other materials containing stone;

– Solvent from solvent-containing paint/

varnish;

– Arsenic, chromium and other wood pre-

servatives;

– Materials for pesticide treatment on boat

and ship hulls;

– Stainless steel dust, metal dust and non-

ferrous metal dust;

To minimize the unwanted intake of these

materials:

– Use dust extraction matched appropriately

for the developing dust.

– Use personal protective equipment, such

as a P2 filter-class dust protection mask.

– Provide for good ventilation of the work-

place.

The risk from inhaling dusts depends on how

often these materials are worked. Materials

containing asbestos may only be worked on

by specialists.

Wood and light-metal dust can

cause spontaneous combus-

tion or explosions.

Hot mixtures of sanding dust and paint/varnish

remainders or other chemical materials in the

filter bag or the vac filter can self-ignite under

unfavorable conditions, such as sparking from

sanding metal, continuous sunlight or high

ambient temperatures. To prevent this:

– Avoid overheating the material being

sanded and the power tool.

– Empty the dust collector/container in time.

– Observe the material manufacturer’s

working instructions.

– Observe the relevant regulations in your

country for the materials being worked.

Hand/arm vibrations.

While working with this power

tool, hand/arm vibrations

occur. These can lead to health impairments.

The vibration emission value

during actual use of the power

tool can differ from the declared value

depending on the ways in which the tool is

used.

It is necessary to identify safety

measures to protect the oper-

ator that are based on an estimation of expo-

sure in the actual conditions of use.

The vibration emission level given in this

information sheet has been measured in

accordance with a standardised test given in

EN 60745 and may be used to compare one

tool with another. It may be used for a pre-

liminary assessment of exposure.

The declared vibration emission level repre-

sents the main applications of the tool. How-

ever if the tool is used for different

applications, with different accessories or

poorly maintained, the vibration emission

may differ. This may significantly increase the

exposure level over the total working period.

An estimation of the level of exposure to

vibration should also take into account the

times when the tool is switched off or when

it is running but not actually doing the job.

This may significantly reduce the exposure

level over the total working period.

Identify additional safety measures to protect

the operator from the effects of vibration

such as: maintain the tool and the accessories,

keep the hands warm, organisation of work

patterns.

WARNING

CAUTION

WARNING

OBJ_BUCH-0000000194-003.book Page 8 Friday, December 11, 2015 12:00 PM

9

en

Emission values for sound and vibration (Two-figure – specifications as per ISO 4871)

Sound emission WSG7-115

A-weighted emission pressure power level measured at the workplace

L

pA

(re 20 μPa), in decibels 91

Measuring uncertainty

K

pA

, in decibels 3

Measured A-weighted sound power level

L

wA

(re 1 pW), in decibels 102

Measuring uncertainty

K

wA

, in decibels 3

C-weighted peak sound pressure level measured at the workplace

L

pCpeak

,

in decibels 105

Measuring uncertainty

K

pCpeak

, in decibels 3

Vibrations

Mean vibrational value for angle grinding

h,AG

, in

– m/s

2

– ft/s

2

6.5

21.3

Mean vibrational value for sanding with sanding sheet

h,DS

, in

– m/s

2

– ft/s

2

3.5

11.5

Measuring uncertainty

K

, in

– m/s

2

– ft/s

2

2.0

6.6

REMARK: The sum of the measured emission value and respective measuring inaccuracy

represents the upper limit of the values that can occur during measuring.

Wear hearing protection!

Measured values determined in accordance with the corresponding product standard.

OBJ_BUCH-0000000194-003.book Page 9 Friday, December 11, 2015 12:00 PM

10

en

Extension cable.

If the use of an extension cord

is required, its length and con-

ductor cross-section must be adequate for the

application in order to prevent a voltage drop

in the extension cord, power loss and over-

heating of the power tool. Otherwise, the

extension cable and power tool are prone to

electrical danger, and the working efficiency is

decreased.

Recommended dimensions of extension

cables at an operating voltage of 120 V – sin-

gle-phase a. c., with only one power tool

WSG7-115 connected:

Intended use of the power tool:

Hand-guided angle grinder for dry grinding,

sanding with sanding discs, working with wire

brushes and cutting of metal and stone in

weather-protected environments with the

application tools and accessories recom-

mended by FEIN.

Operation of the power tool off power generators.

This power tool is also suitable for use

with AC generators with sufficient power

output that correspond to the Standard

ISO 8528, design type G2. This Standard is

particularly not complied with when the so-

called distortion factor exceeds 10 %. When

in doubt, please refer to the generator

instruction/specification guide.

Operating the power tool off

power generators whose no-

load speed exceeds the voltage value on the

type plate of the power tool is prohibited.

WARNING

Max. cable length, ft Max. cable length, m

≤ 100 100

–200

200

–300

≤ 30 30

– 60

60

–100

Min. conductor size

A.W.G.

Min. conductorcross-

section, mm

2

16 14 12 1.5 2.5 4

WARNING

OBJ_BUCH-0000000194-003.book Page 10 Friday, December 11, 2015 12:00 PM

11

en

Symbols.

Symbol, character Explanation

General prohibition sign. This action is prohibited.

Do not touch the rotating parts of the power tool.

Observe the instructions in the text or graphic opposite!

Make sure to read the enclosed documents such as the Instruction Man-

ual and the General Safety Instructions.

Before commencing this working step, pull the power plug out of the-

socket. Otherwise there will be danger of injury if the power tool

should start unintentionally.

Use eye protection during operation.

Use ear protection during operation.

Use protective gloves during operation.

Use a dust mask during operation.

A surface that can be touched may be very hot and thus hazardous.

This symbol confirms the certification of this product for the USA and

Canada.

This sign warns of a directly imminent, dangerous situation. A false reac-

tion can cause a severe or fatal injury.

This sign indicates a possible dangerous situation that could cause severe

or fatal injury.

This sign warns of a possible dangerous situation that could cause injury.

Worn out power tools and other electrotechnical and electrical prod-

ucts should be sorted separately for environmentally-friendly recycling.

Product with double or reinforced insulation

Product with build-up of protection class III

~ or a. c. Alternating current

or d. c. Direct current

1~ Alternating current, single-phase

DANGER

WARNING

CAUTION

OBJ_BUCH-0000000194-003.book Page 11 Friday, December 11, 2015 12:00 PM

12

en

Character Unit of measurement, national Explanation

n

0

rpm; /min; min

-1

; r/min Rated speed

P

W Electrical power

°Angle width

U V Electric voltage

f Hz Frequency

I

A Electric current intensity

m

kg, lbs Mass

l ft, in Length, width, height, depth, diameter or thread

Ø

ft, in Diameter of a round part

m, s, kg, A, mm, V, W, Hz, N,

°C, dB, min, m/s

2

Basic and derived units of measurement from

the international system of units SI.

OBJ_BUCH-0000000194-003.book Page 12 Friday, December 11, 2015 12:00 PM

13

en

Technical description and specifications.

Before mounting or replacing cutting tool or accessories, pull the power plug.

This preventive safety measure rules out the danger of injuries through acciden-

tal starting of the power tool.

All accessories described or shown in this instruction manual will not be included with your-

power tool.

WARNING

Locking button

Grinding disc

Wheel guard

On/Off switch

Auxiliary handle

Gripping surface

Fig. 1

OBJ_BUCH-0000000194-003.book Page 13 Friday, December 11, 2015 12:00 PM

14

en

Type WSG7-115

Order number 7 221 97

Current consumption 6.6 A

Type of current ~ (a. c.)

Rated speed 12000 rpm

Ø

D

=Max. diameter of grinding/cutting disc 4 1/2 in

115 mm

Diameter of mounting hole 7/8 in

22.23 mm

Thickness of grinding/cutting disc 1/16 in – 1/4 in

1 mm–6 mm

Max. sanding pad diameter 4 1/2 in

115 mm

Thread for clamping flange 5/8 in–

11UNC

Length of mounting thread 3/4 in

20 mm

Weight according to EPTA-Procedure 01 3.7 lbs

(1.7 kg)

Class of protection /II

OBJ_BUCH-0000000194-003.book Page 14 Friday, December 11, 2015 12:00 PM

15

en

Assembly instructions.

Before mounting or replacing cutting tool or accessories, pull the power plug.

This preventive safety measure rules out the danger of injuries through acci-

dental starting of the power tool.

Mounting the auxiliary handle

(figure 2).

Depending on the working manner, screw

the auxiliary handle right or left on the power

tool.

Mounting the wheel guard (figure 3).

Loosen the clamping screw.

Insert the wheel guard ensuring that the cams

of the opening engage in the grooves on the

power tool.

Turn the wheel guard to the requested work-

ing position, then clamp the wheel guard with

the clamping screw.

Mounting the cut-off wheel guard

For cut-off grinding opera-

tions, always work with the

cut-off wheel guard mounted.

Mounting takes place as described under

“Mounting the wheel guard”.

WARNING

2.

1.

Fig. 2

Auxiliary handle

1.

4.

3.

2.

Clamping screw

Fig. 3

Wheel guard

WARNING

OBJ_BUCH-0000000194-003.book Page 15 Friday, December 11, 2015 12:00 PM

16

en

Changing the tool.

Before mounting or replacing cutting tool or accessories, pull the power plug.

This preventive safety measure rules out the danger of injuries through acciden-

tal starting of the power tool.

Mounting a grinding disc (figure 4).

Press the locking button only when the

motor is stopped.

Press the locking button completely through

and hold it in place. Loosen the clamping

flange with the pin-type face wrench.

Unscrew the clamping flange.

Replace the used-up grinding accessory

or insert a new one.

Pay attention that the grinding accessory

is properly centered between the sup-

port flange and the clamping flange.

Manually screw on the clamping flange again.

Press the locking button completely through

and hold it in place. Tighten the clamping

flange with the pin-type face wrench.

Note: Pay attention to the mounting direction

of the clamping flange, which can vary

depending on the thickness of the grinding

disc.

WARNING

6 mm

1/4 in

6 mm

1/4 in

Clamping flange

Support flange

4.

1.

3.

2.

Fig. 4

OBJ_BUCH-0000000194-003.book Page 16 Friday, December 11, 2015 12:00 PM

17

en

Adjustments.

Before mounting or replacing cutting tool or accessories, pull the power plug.

This preventive safety measure rules out the danger of injuries through acciden-

tal starting of the power tool.

Adjusting the wheel guard (figure 5).

Loosen the clamping screw.

Turn the wheel guard to the requested work-

ing position, then clamp the wheel guard with

the clamping screw.

Turning the gear head

Carefully turn the gear head to the new posi-

tion without removing it from the housing.

WARNING

1.

3.

2.

Clamping screw

Fig. 5

Wheel guard

OBJ_BUCH-0000000194-003.book Page 17 Friday, December 11, 2015 12:00 PM

18

en

Working instructions.

Before mounting or replacing cutting tool or accessories, pull the power plug.

This preventive safety measure rules out the danger of injuries through acciden-

tal starting of the power tool.

For each job, use only the FEIN application tool released and intended for the respective

application.

Switching on and off (figure 6).

Check the power supply cable

and the plug for damage.

Always hold the power tool

firmly. Otherwise, you could

lose control over the power tool.

Switching on:

Push the On/Off switch forward (I).

Switching off:

Press the switch downward ().

Securing the workpiece (figure 7).

Secure the workpiece sufficiently. An

inadequately secured workpiece can, for

example, cause the grinding accessory to

jam. This can lead to kickback, cause the

workpiece to fall down, and lead to

other dangerous situations.

WARNING

CAUTION

On/Off switch

Fig. 6

Fig. 7

OBJ_BUCH-0000000194-003.book Page 18 Friday, December 11, 2015 12:00 PM

19

en

Dry grinding (figure 8).

Observe a lead angle of 20 – 40°. This will

ensure a good removal rate.

Apply uniform pressure with the power

tool and move it over the surface.

Avoid excessive heating of the work-

piece surface.

Cutting (figure 9).

Always work in an up-grinding motion,

so that the cutting disc will not jump out

of the cut.

Fig. 8

Fig. 9

OBJ_BUCH-0000000194-003.book Page 19 Friday, December 11, 2015 12:00 PM

20

en

Repair and customer service.

Before mounting or replacing cutting tool or accessories, pull the power plug.

This preventive safety measure rules out the danger of injuries through acciden-

tal starting of the power tool.

Exchangeable parts

If required, you can change the following

parts yourself:

Application tools, auxiliary handle, clamping

flanges, wheel guard

The current spare parts list for this power

tool can be found in the Internet at

www.fein.com.

Service.

Have maintenance carried out

only through qualified person-

nel. Incorrectly mounted leads and compo-

nents can cause serious injuries. Have the

required service carried out only through a

FEIN customer service agent.

Cleaning.

Prior to any cleaning or main-

tenance, disconnect the power

tool from the power supply in order to avoid

accidents.

When using in environments

with conductive dust in the air,

such as when cutting metals, this dust can

settle in the interior of the power tool. This

can impair the total insulation of the power

tool. Therefore, regularly blow out the interior

of the power tool from outside via the ventila-

tion openings with dry, oil-free compressed

air; always wear eye protection when doing

this. For additional protection, connect a

ground fault circuit interrupter (GFCI) on the

line side.

Do not attempt to clean

clogged or dirty ventilation

openings of the power tool with pointed

metal objects; use nonmetal tools or objects

if necessary.

Do not use cleaning agents

and solvents that can cause

damage to plastic parts. These include: Gas-

oline, carbon-tetrachloride, chloric solvents,

ammonia and domestic cleaning agents that

contain ammonia.

If the supply cable of this

power tool is damaged, it

must be replaced by a specially prepared cable

available through the FEIN customer service

center.

Warranty and liability.

The warranty for the product is valid in accordance with the legal regulations in the country

where it is marketed. In addition, FEIN also provides a guarantee in accordance with the FEIN

manufacturer’s warranty declaration.

All accessories described or shown in this instruction manual will not be included with your-

power tool.

Environmental protection, disposal.

Packaging, worn out power tools and accessories should be sorted for environmental-friendly

recycling.

For further information, please contact your specialist shop.

WARNING

CAUTION

OBJ_BUCH-0000000194-003.book Page 20 Friday, December 11, 2015 12:00 PM

La page charge ...

FEIN WSG7-115 Manuel utilisateur

Ce manuel convient également à

FEIN WSG7-115 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents