Maxon DX-300 Manuel utilisateur

Maxon
Marque
Maxon
Modèle
DX-300
Catégorie
Radios bidirectionnelles
Taper
Manuel utilisateur
User Manual
Version #1 (2023-05-30)
UHF Transceiver
DX-300
2
1. DX-300 Features
With built-in antennas, the DX-300 is simple and easy to carry with it, as it fits perfectly in the palm of
your hand. Swivel belt clips minimize inconvenience and provide convenience for users to act freely
when the radio is attached to the body. DX-300 provides stress-free communication through activities
such as hotels, restaurants, large shops, amusement facilities, and various leisure sports.
⚫ Digital (TierⅠ, Ⅱ TDMA) or Analog Mode.
⚫ 512 Channel Capacity; 1 Zones 16 (1zone = Max 16 Channels)
⚫ Mixed Channel Operation (Analog reception in Digital mode)
⚫ 2 / 0.5 Watt RF Power Setting
⚫ Encryption Mode (AES256)
⚫ Single equipment running Business Radio(DMR)/GMRS/FRS
⚫ Channel Announcement
⚫ Battery Remaining Announcement
⚫ Multiple Scan Modes
⚫ Time-Out Timer (TOT)
⚫ Safety mode(Lone Worker)
⚫ Emergency / Siren
⚫ Etiquette (Vibration) Function (Option)
⚫ Electronic volume control
⚫ Voice recording and playback
⚫ VOX (Voice Operated Transmit)
⚫ Remote Radio Stun / Revive
⚫ Built in Speaker & MIC
⚫ 1Watt Audio output
⚫ Swivel Belt Clip
⚫ 2 Pin accessory connector
⚫ Bright and vivid TFT LCD screen
⚫ IP67 waterproof
⚫ DC+3.7V Li-ion / 2,000Mah
3
2. Specification
DX-300
General
Frequency Range
Frequency Stability
Programmable Channels
Channel Spacing
Digital Vocoder
Dimensions
Weight
Power Source
Current Drain (maximum)
DX-300 : 440 ~470 MHz
±1.5ppm
512 (1 Zones = Max16 Channels)
12.5KHz
AMBE++ Voice Compression Algorithm
86mm(H) x 51.5mm(W) x 22mm(D)
100g
DC +3.7V Li-ion 2,000mAH Battery
Receive mode, rated audio out – 420 (Audio Max)
Transmit mode – 1,200mA
Standby mode – 100mA
Receiver
Sensitivity
Squelch Sensitivity
Selectivity
Spurious and Harmonic Rejection
FM Hum and Noise
Audio Output Power
Audio Distortion
Audio Response
Input Impedance
Transmitter
RF Power Output
Adjacent Channel Power
Spurious and Harmonic
FM Hum and Noise
Audio Distortion
Audio Frequency Response
Output Impedance
4
3. DX-300 Package Contents
Radio Unit Swivel Belt Clip 1 Slot Charger
User Manual
Figure 3-1) DX-300 Main Package Contents
5
4. Control Buttons & LCD Display
Figure 4-1) Appearance DX-300
6
Figure 4-2) LCD Icon Explanation
5. Button and Jack Operations
Button & Jack
Operation Description
Power ON/OFF
Pressing the Power ON/OFF button will cause the MAXON logo to appear on the
LCD and power on with a sound. Pressing the Power ON/OFF switch for more
than 2 seconds with the Radio on will turn off the power with the "Goodbye"
comment.
On the menu mode, to return to the upper Menu, press the "Power On/Off"
button.
PTT Button
The radio transmits voice when pressing PTT button. It receives Voice when
releasing the PTT button. In order to have clear sound when transmitting, it is
recommended to speak around 5~7cm away from the MIC.
Volume UP Button
If you press Volume/Channel UP Button with Radio turned on, the voice
becomes louder one step at a time. Volume consists of a total of 16 steps.
To select the Menu options, press the "Volume/Channel UP/down Button" to
move from side to side menu.
Volume Down
Button
If you press Volume/Channel Down Button with Radio turned on, the voice
increases or decreases step by step. Volume consists of a total of 16 steps.
To select the Menu options, press the "Volume/Channel UP/down Button" to
move from side to side menu.
Menu Button
To Enter the Menu mode, press the "Menu Button". Digital mode provides three
menu options such as Contacts, Record, and Settings. And Analog mode
provides only the Setting option.
On the menu mode, to dismiss the menu options and return to the welcome
screen, press the "Menu button" for about 2 seconds.
2 Pin MIC Jack
2 Pin MIC Jack is used for :
1) the Accessory Speaker MIC
2) programming cable to set CPS Program
3) communicating with external terminals
7
6. Installation and Removal
6.1 Belt Clip Installation and Removal
Please refer to figure 6-1.
To attach the Swivel belt clip to DX-300, align the belt clip to the back of DX-300 as shown the
figure 5-1 and push it down to direction 1. The clip will "click" when locked. To remove the belt clip,
push the belt clip locking tab into direction 2 and pull the belt clip up to direction 3.
In case the user wears the DX-300 around the waist, the belt clip can turn to direction 4 or 5 to
make it more convenient.
Figure 6-1) Belt Clip Installation and Removal
6.2 External Accessory Connector Jack
To connect external accessories as shown in figure 6-2, open the accessory jack cover, align the
DX-300 and the accessory, and then push-in the accessory. To remove the accessory,
carefully pull-out the accessory connector from the middle of the connector and close
the accessory cover to re-seal the jack.
8
Figure 6-2) Jack for an external Accessory
7. Charging the Battery
When the DX-300 is inserted into the XC-400D charger, the LCD screen displays the state of
charge and the battery Icon indicates the full charge when charging is complete.
DX-300 can be charged by a USB C-type adapter for a mobile phone.
7.1 The Time of Charging
Low battery voltage may reduce communication coverage and also degrade performance.
Please charge the battery in case of the following:
1) When the performance has been degraded.
2) When the battery Icon blinks indicating low battery.
3) When you hear the 'Warning sound' during operation.
7.2 How to Charge
DX-300 can be charged with an XC-400D charger and a USB C-type adapter for mobile phones.
1) Charging
9
Figure 7-1) XC-400D Charger
2) Charging with USB C-Type charger
Inset a USB C-type adapter into the USB C-Type Jack.
Figure 7-2) USB C-type charger
10
8. DX-300 Operations
- MENU Functions
To enter the menu tree as displayed in Figure7, press the menu button.
When pressing the menu button once more while in the menu, it moves to detailed menu
section of the selected one.
Figure 8) DX-300 Menu Tree
☞ Note) If the menu is not operated for at least 25 seconds after launch, the radio will revert to
standby mode.
11
1) Contact List (Digital Mode Only)
The Contact List Provides a list of individuals, groups or all calls of which you can make a
direct call. The lists of contact are set within the radio by the CPS. To initiate a call, select the
Contact section from the menu. Press the menu/enter button to see the list of contact, press
the ▲▼ keys to the desired contact and press the PTT button to initiate the call. The radio will
revert to the original contact/channel after a preset time as set by the CPS. When you enter in
the contact menu, the applicable icon will be shown indicating the type of call.
ICON.
-: Individual Contact List
-: Group Contact List
- : All Contact List (Can be used the terminals with the same channel and color code)
2) Voice Record (Digital Mode Only)
This function is used to record the content of outgoing and incoming calls in digital mode
only. There are 3 choices of Settings, Lists, and Delete All. Up to 63
conversations/recordings can be stored with each recording limited to 150 seconds. When
the recordings exceed 63, the oldest message is cleared and the newest incoming message
is registered,
Settings - This section allows the capability to turn the recording capability on off.
Lists – This section allows the viewing of the recorded messages and to play back each
message. To play back a message, use the ▲▼ key to the desired message and press the
menu/enter button to play the recording.
Delete all – This function provides the capability to delete stored recordings. To delete
recordings, select Delete All from within the Voice Recording menu by pressing the menu/enter
button, the question to delete All will appear with the word “Yes” Press the menu/enter button to
delete all messages. If you choose not to delete the messages, press the return button to exit
out.
3) Settings
The Settings menu provides three options as Device Setting, Function Setting, and Radio
Information.
1. Device Setting: Channel , Sound , Backlight, LED , Keypad Lock, Etiquette , Screen ,
Language can be set up.
2. Function Setting: Analog Mode and Digital Mode provide different options. Analog mode
provides SubTone and SQ level and Digital mode provides Encryption, color code, Radio ID.
VOX, Lone Worker, BCL/BCLO, and Scan On/Off are provided in common for Analog and
Digital.
12
3. The Radio Info menu provides information on the main device.
(1) Device Setting
① Channel Set
‘Channel Set’ allows you to select the channel to make a call. The channel can be set up
through the CPS Program.
② Sound
'Sound' allows you to set up all the sounds of the device. In the volume menu, the sound can
be set up as off, Soft, Medium, and Loud. In the Call Tone, the call-related sound
transmitted/received can be set as On/Off.
③ Backlight
This function allows the backlight of the LCD to be turned ON/OFF and timed. The duration
for the timed section is set via the PS. Contact your Authorized Dealer for further information.
④ LED Control
This function is to set the enable or disable the radio status LED. The LED status can be set
via the PS.
⑤ Keypad Lock
This is function locks the keypad to prohibit the accidental press of keys and buttons. When
the keypad lock is enabled, all keys/buttons are locked except the PTT button and power ON/
OFF button. If any of these buttons are pushed, the keypad lock will enable again after 25
seconds from the pressing of the last button. Press the program key (by CPS) to temporarily
unlock the keypad for 25 seconds.
⑥ Etiquette
This function informs you of an incoming call by vibration without making a reception sound.
When you want to hear the sound of the call, press the button to hear the voice of the call.
When there is no button input by the user for 30 seconds after the call, it is switched to
etiquette mode (vibration mode).
⑦ Screen Setting
Screen Setting provides two settings options, Screen Type and Screen Kind. Screen Type
provides four Welcome screens and Screen Kind provides two options, Bright Screen and
Dark Screen for the entire color of the TFT LCD screen.
13
This function allows the ability to change between Screen1 for Numeric or Screen2 for
Alphanumeric. The information displayed is set via the PS. Contact your Authorized Dealer for
further information
⑧ Language
This function is to select the language (English or Korean) for the menus.
(2) Function Setting
① SubTone (Analog Mode Only)
SubTone functions only on the Analog Channel. The user may set three subTones of
CTCSS/DCS/Reverse DCS.
② Encryption (Digital Mode Only)
It is a function to encrypt transmission and reception voice.
Voice Encryption function can be set for each channel on all digital channels.
The voice encryption code is set in the CPS program and provides 128/192/256-bit
encryption
③ VOX
VOX function allow transmitting without using the PTT button.
VOX sensitivity level is adjusted from 1 to 5 with 5 being the most sensitive.
④ Lone Worker (Digital Mode Only)
This function can inform others about your safety within the time set in the menu. Contact
your authorized Dealer for further information.
⑤ BCL/BCLO
This function prevent interference when the channel is busy.
-. Digital Mode Only
BCL On: If the current channel is busy, the transmission is prohibited.
-. Analog Mode
BCL On & BCLO Off: If the current channel is busy, transmitting is prohibited.
BCL On & BCLO On: Transmitting occurs when it matches the received tone.
⑥ Squelch Level (Analog Mode only)
This function allows the ability to change the squelch levels of Open, 1,2,3,4, or Tight.
14
⑦ Color Code (Digital Mode Only)
This functions to change the color code value on the Digital Channel. The Color Code
value can be set from 0 to 15.
⑧ Radio ID (Digital Mode Only)
The Radio ID allows you to change the OWN ID value of the Radio used for Digital Channel
calls.
⑨ Scan On/Off
This function provides the ability to turn scan on/off with the scan list as programmed into the
radio via the PS. The ability to scan digital and analog channels are available. Contact your
Authorized Dealer for further information.
(3) Radio Info
This informs all the information of the device such as Radio ID, Mode Name, PCB
Version, Frequency Range, SW Version, BB Number, BB Version, Last Update, Made
Date, and DB Version.
15
9. Precautions
9.1 Precautions for safe operation
Don’t use other manufacturer’s accessories (such as rechargeable battery,
adaptor, external speaker microphone and earphone, etc.). Unknown or
unauthorized accessories may damage the radio and void the warranty.
Don’t disassemble or reorganize the Radio. The disassembly or
reorganization of your radio is punishable by law and can cause damage to
the radio that will not be covered by the warranty.
Don’t use frequencies you do not have a permit for.
Avoid excessive shock to the Radio. Don’t place the Radio where the direct
sunlight and/or the high temperature occurs, battery damage can occur in
this environment. Do not disassemble or damage the battery pack.
9.2 Do not use the radio where prohibited
The radio emits an electronic wave which may have an effect on the operation of other
equipment and can also be affected by those other devices.
Please turn off the radio before boarding an airplane. If you want to use the
radio during flight, please adhere to the aircraft’s rules.
If using the radio in an area where medical equipment is being used, please
get permission from the staff before use to prevent interference issues.
Be careful when using your radio in a place where computers or other
electronic devices are being used because the strong electronic waves from
the radio can affect this equipment.
16
10. Safety Notes & FCC
Please make sure to read the followings above for safe and effective use of the radio.
⚫ Please keep the Radio away at least 1 inch from the body.
⚫ Do not touch antenna if it is damaged. Risk of skin burn can occur if the
outside surface of antenna gets stripped out.
⚫ Please be careful when putting the battery in a pocket or a bag. If you
contact a conductive metal to a battery terminal, there is a heat and fire
risk to your radio.
⚫ Please don’t listen to the radio at a high-volume level when using
earphones. Loud volume may have a lasting bad effect on your hearing.
⚫ It is recommended to adjust the volume step by step to the level you
want after you set the radio volume of the radio at a low level.
⚫ Please don’t remove or replace or charge or discharge the battery in a
hazard area where sparks could cause an electrical fire.
⚫ Turn off the radio in areas where there is a strong electromagnetic force.
17
FCC statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
This device and its antenna(s) must not be co-located or operation in conjunction with any other
antenna or transmitter.
Radiation Exposure Statement
To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed
and operated with minimum distance of 2.5cm from your body.
RF Energy Exposure Awareness and Control Information and Operational Instructions for
Occupational Use
Notice: this radio is intended for use in occupational/controlled conditions where users have full
knowledge of their exposure and can exercise control over their exposure to meet the
occupational limits in FCC and International standards. This radio device is NOT authorized for
general population consumer use.
18
Federal Communication Commission (FCC) Regulations
When Device is used as a consequence of employment, the FCC requires users to be fully aware
of and able to control their exposure to meet occupational requirement. Exposure awareness can
be facilitated by the use of a product label directing users to specific user awareness information.
Your Device has a RF Exposure Product Label. Also, your Device Radio user manual includes
information and operating instructions required to control your RF exposure and satisfy
compliance requirements.
Compliance with RF Exposure Standards
Your Device is designed and tested to compliance with a number of national and international
standards and guidelines for human exposure to radio frequency electromagnetic energy. This
radio compliance with the IEEE (FCC) and ICNIRP exposure limits for occupational/controlled RF
exposure environments at operating duty factors of up to 50% talk – 50% listen and is approved
for occupational use only. In terms of measuring RF energy for compliance with these exposure
guidelines, your radio generates measureable RF energy only while it is transmitting (during
talking), not when it is receiving (listening) or in standby mode.
Your Device complies with the following RF energy exposure standards and guidelines:
● United States Federal Communications Commission (FCC), Code of Federal Regulations;
● Institute of Electrical and Electronic Engineers (IEEE) C95.1
● International Commission on Non-lionizing Radiation Protection (ICNIRP)
RF Exposure Compliance and Control Guidelines and Operating Instructions for Two-Way Radio
Operations
To control your exposure and ensure compliance with the occupational/controlled environment
exposure limits, always adhere to the following procedures;
● DO NOT remove the RF Exposure Label from the device
● User awareness instructions should accompany device when transferred to other users.
Operational Instructions and Training Guidelines
To ensure optimal performance and compliance with the occupational/controlled environment RF
energy exposure limits in the above standards and guidelines, users should transmit no more than
50% of the time and always adhere to the following procedures;
● In front of the face, hold the radio in a vertical position with microphone (and other parts
of the radio including the antenna) at least 2.5 centimeters away from the nose or lips. Keep the
radio at a proper distance is important to ensure compliance.
Note: RF exposure decrease with increasing distance from the antenna.
19
● Body Worn Operation; when worn the body, always place the radio in an approved clip,
holder, or body harness for this product.
Using approved body-worn accessories is important because the use of non-approved accessories
may results in exposure levels, which exceed the occupational/controlled environment RF exposure
limits
Using only approved supplied or replacement antennas, batteries, and audio accessories, use of
non-approved antennas, batteries, and wired or wireless accessories may exceed the applicable RF
exposure guidelines (IEEE, ICNIRP or FCC).
20
IC statement
English Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science
and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following
two conditions: 1, This device may not cause interference. 2, This device must
accept any interference, including interference that may cause undesired operation of the device.
Safety Information
This equipment complies with IC radiation exposure limits set forth for an controlled
exposure environment. When the talk bottom is pushed, it sends out radio frequency (RF)
signals. The devices is authorized to operate at a duty not to exceed 50%.
For body-worn operation, this radio has been tested and meets the IC RF exposure guidelines
when used with manufacturer accessories supplied or designated for this product. Use of
other accessories may not ensure compliance with FCC RF exposure guidelines. Use only the
supplied antenna. Unauthorized antennas, modifications, or attachments could damage the
transmitter and may violate FCC regulations.
To maintain compliance with RF Exposure guidelines, This equipment should be installed and
operated with minimum distance of 2.5cm from your body.
Canada Déclaration
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne
doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.”
l'information sur la sécurité
ce matériel est conforme aux limites de dose d'exposition aux rayonnements énoncés pour
contrôlées l'exposition environnement.quand le parler bas est poussé, il envoie des signaux radio
fréquence (RF). les dispositifs est autorisée à exploiter, à une obligation de ne pas dépasser 50%.
opération portés sur le corps, la radio a été testé et respecte les directives d'exposition aux IC RF
utilisée avec le fabricant d'accessoires fournis ou désignés pour ce produit. utilisation d'autres
accessoires ne peut s'assurer de la conformité avec les lignes directrices sur l'exposition aux
radiofréquences. utiliser uniquement la fournies antenne. les modifications ou les antennes de non
autorisée, pourrait nuire à l'émetteur et peuvent violer les règlements de la IC.
l'émetteur à environ 2.5cm de votre visage et parlez normalement, avec l'antenne a signalé et loin.
RF Energy Exposure Awareness and Control Information and Operational Instructions for
Occupational Use
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23

Maxon DX-300 Manuel utilisateur

Maxon
Marque
Maxon
Modèle
DX-300
Catégorie
Radios bidirectionnelles
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Autres documents