Operator’s Manual
NIGHT-LITE™ GR-Series Chain
Manuel d'utilisation
NIGHT-LITE™ GR-Series la chaîne
Manual del operario
NIGHT-LITE™ Serie GR la cadena
Copyright © 2022 Briggs & Stratton
Milwaukee, WI, USA All rights reserved.
Part No.: 118240
Revision: D
en
fr
es
www.allmand.com2
Recording the equipment information will help when placing
an order for replacement parts and/or decals.
Manual Contents:
Record Important Information
California Proposition 65 ................................................. 2
Introduction ....................................................................... 2
Products Covered by This Manual ................................... 2
Safety ................................................................................. 2
Features and Controls ...................................................... 6
Preparing the Light Tower Trailer for Use ...................... 7
Transporting the Light Tower Trailer ............................ 8
Operation ......................................................................... 13
Maintenance .................................................................... 20
Specications .................................................................. 22
Troubleshooting .............................................................. 22
Reporting Safety Defects ................................................ 23
Tire Safety Information .................................................... 23
Company Equipment No:
Unit Model No:
Unit VIN:
Accessories:
Introduction
About This Manual
TAKE TIME TO READ THIS MANUAL THOROUGHLY
This instruction manual provides necessary instructions for
the Allmand® Night-Lite™ GR-Series Chain Light Tower.
The information found in this manual is in eect at the time
of printing. Briggs & Stratton, LLC. may change contents
without notice and without incurring obligation.
The images throughout this manual are representative, and
may dier from your model.
Any reference in this manual to left or right shall be
determined by looking at the trailer from the rear.
Products Covered by This
Manual
The following products are covered by this manual:
Night-Lite™ GR-Series Chain
Safety
For your safety, the safety of others, and to protect the
performance of equipment, follow the precautions listed
throughout the manual before operation, during operation
and during periodic maintenance procedures.
Indicates a potential personal injury hazard.
DANGER
Indicates a hazardous situation which, if not avoided, will
result in death or serious injury.
WARNING
Indicates a hazardous situation which, if not avoided, could
result in death or serious injury.
CAUTION
Indicates a hazardous situation which, if not avoided, could
result in minor or moderate injury.
Safety Denitions
NOTICE
Information considered important but not hazard related.
The following section contains general safety precautions
and guidelines that must be obeyed to reduce risk to
personal safety. Special safety precautions are listed in
specic procedures. Read and understand all of the safety
precautions before operating or performing repairs or
maintenance.
Safety Precautions
California Proposition 65
WARNING
Cancer and reproductive harm.
www.P65Warnings.ca.gov
If uncertain about any of the information in the manual,
contact the Allmand service department at 1-800-562-1373,
or contact us through the Allmand website, www.allmand.
com.
Save these original instructions for future reference.
en
English 3
DANGER
Electrocution Hazard
• Always check overhead wires and obstructions before
raising or lowering the light tower.
• Always obey the rules or instructions for your work
site and state, province and national electric code for
maintaining a safe distance from overhead wires.
• High voltage is present when the unit is connected to
a power source. Never attempt to service electrical
components while the unit is connected to a power
source.
• Do not operate the light tower if the insulation on
the electrical cord or other electrical wiring is cut or
worn or if bare wires are exposed. Repair or replace
damaged wiring before operating the light tower
WARNING
Unsafe Operation Hazard
• Never permit anyone to install or operate the
equipment without proper training.
• Read and understand this Operator’s Manual and
any other component manuals before operating
or servicing the light tower to make sure that safe
operating practices and maintenance procedures are
followed.
• Safety signs and decals are additional reminders for
safe operating and maintenance techniques.
WARNING
Fall Hazard
• Never carry riders on the equipment.
WARNING
Modication Hazard
• Never modify the equipment without written consent
of the manufacturer. Any modication could aect the
safe operation of the equipment.
WARNING
Exposure Hazard
• Always wear personal protective equipment, including
appropriate clothing, gloves, work shoes, and eye and
hearing protection, as required by the task at hand.
WARNING
Rollover Hazard
• Do not raise, lower or use light tower unless all
outriggers and jacks are positioned on rm ground.
• Never move or reposition the light tower while the
light tower is extended in the vertical position.
WARNING
Alcohol and Drug Hazard
• Never operate the light tower while under the
inuence of alcohol or drugs, or when ill.
WARNING
Flying Object Hazard
• Always wear eye protection when cleaning the
equipment with compressed air or high pressure
water. Dust, ying debris, compressed air, pressurized
water or steam may injure your eyes.
WARNING
Burn Hazard
• Some of the surfaces become very hot during
operation and shortly after shutdown.
• Keep hands and other body parts away from hot
surfaces.
• Handle hot components with heat resistant gloves.
NOTICE
• Any part which is found defective as a result of
inspection or any part whose measured value does
not satisfy the standard or limit MUST be replaced.
• Always tighten components to the specied torque.
Loose parts can cause equipment damage or cause it
to operate improperly.
• Follow the guidelines of the Environmental Protection
Agency (EPA), Environment Canada (EC) or other
governmental agencies for the proper disposal of
hazardous materials.
• Only use replacement parts specied. Other
replacement parts may eect warranty coverage.
• Clean all accumulated dirt and debris away from the
body of the equipment and its components before
you inspect the equipment or perform preventative
maintenance procedures or repairs. Operating
equipment with accumulated dirt and debris will cause
premature wear of equipment components.
• Never dispose of hazardous materials by dumping
them into a sewer, on the ground, or into groundwater
or waterways
www.allmand.com4
• Retrieve any tools or parts that may have dropped
inside of the equipment to avoid improper equipment
operation.
• If any alert indicator illuminates during equipment
operation, stop the unit immediately. Determine the
cause and repair the problem before continuing to
operate the equipment.
Safety Decals
Before operating your unit, read and understand the
following safety decals. The cautions, warnings, and
instructions are for your safety. To avoid personal injury or
damage to the unit, understand and obey all the decals.
Keep the decals from becoming dirty or torn, and replace
them if they are lost or damaged. Also, if a part needs to
be replaced that has a decal attached to it, make sure to
order the new part and decal at the same time.
If any safety or instructional decals become worn or
damaged, and cannot be read, order replacement decals
from your dealer.
Domestic Models
DANGER - Entering electrical
compartment while equipment is
in operation will result in death or
serious injury. Unplug equipment
before entering electrical
compartment.
Part No. 118074
118074
CSA File Number
Part No. 118080
118080
CSA File Number: 204930
CAN ICES-3(B)/NMB-3(B)
C US
Suitable for wet locations.
Convient aux emplacements mouillés.
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Ce dispositif se conforme à la section 15 du règlement de la FCC. Le
fonctionnement est assujetti aux conditions suivantes: (1) Ce
dispositif ne doit pas générer d’interférences nuisibles, et (2) ce
dispositif doit accepter toute interférence, y compris celles qui
porraient entraîner un fonctionnement non désiré.
DANGER - Entering electrical
compartment while equipment is
in operation will result in death or
serious injury. Unplug equipment
before entering electrical
compartment.
WARNING - Failure to follow
warnings, instructions and
operator’s manual could result
in death or serious injury. Read
and follow operator’s manual
before operating or servicing this
equipment.
Part No. 118077
DANGER
Failure to follow warnings,
instructions, and operator’s
manual could result in death
or serious injury.
Open door on control box to locate operator’s
manual. Read and follow operator’s manual
before operating or servicing this equipment.
118077
Entering electrical
compartment while
equipment is in operation
will result in death or
serious injury.
Unplug equipment
before entering electrical
compartment.
Le fait d’entrer dans le
compartiment électrique
tandis que l’équipement est
utilisé causera la mort ou
des blessures graves.
Débrancher l’équipement
avant d’entrer dans le
compartiment électrique.
L’omission de respecter les
avertissements, les
instructions et le manuel de
l’utilisateur peut entraîner des
blessures graves ou la mort.
WARNING
AVERTISSEMENT
Ouvrir la porte sur la boîte de commande
pour trouver le manuel de l’utilisateur. Lire et
suivre le manuel d’utilisation avant de faire
fonctionner cet équipement ou d’en faire
l’entretien.
DANGER
Domestic Models
DANGER - Contacting power lines
when raising light tower will result
in death or serious injury. Keep
light tower far away from power
lines.
WARNING - Raising light tower
without positioning outriggers
and lowering jacks could cause
machine rollover resulting in
death or serious injury. Position
outriggers and lower jacks on a
stable surface before raising light
tower.
WARNING - Standing under
light tower mast and xtures
during lowering operation could
result in death or serious injury.
Keep bystanders away from light
tower during lowering and raising
operations.
WARNING - Handling light xtures
when they are hot could result in
death or serious injury. Keep clear
of light xtures when illuminated
or hot.
WARNING - Looking at illuminated
light xtures could result in serious
injury. Do not look directly at
illuminated light xtures.
CAUTION - Snow and ice could
cause uncontrolled condition in
winch that could result in minor to
moderate injury. Make sure pawl
engages gear. Apply silicone to
ratchet pawl and spacer.
Part No. 122479
Snow and ice could cause
an uncontrolled condition in
winch that could result in
minor to moderate injury.
Make sure pawl engages
gear. Apply silicone to
ratchet pawl and spacer.
CAUTION ATTENTION
La neige et la glace pourraient
causer une condition
incontrôlée du treuil qui
pourrait entraîner une
blessure mineure à moyenne.
S’assurer que le cliquet
embraye dans l’engrenage.
Appliquer du silicone sur le
cliquet et la butée
d’espacement.
122479
Ne jamais regarder
directement des luminaires
allumés.
AVERTISSEMENT
WARNING
Looking at illuminated
light fixtures could result
in serious injury.
Do not look directly at
illuminated light fixtures.
Regarderdes luminaires
allumés pourrait provoquer
de graves blessures.
AVERTISSEMENT
WARNING
AVERTISSEMENT
WARNING
Standing under light tower
mast and fixtures during
lowering operation could
result in death or serious
injury.
Keep bystanders away
from light tower during
lowering and raising
operations.
Raising light tower prior to
positioning outriggers and
lowering jacks could cause
machine rollover resulting
in death or serious injury.
Le fait de soulever la tour
d’éclairage avant de positionner
correctement les longerons et
sans baisser les vérins pourrait
entraîner le basculement de la
machine et provoquer des
blessures graves ou la mort.
Position outriggers and
lower jacks on a stable
surface before raising light
tower.
Il faut positionner les
longerons et abaisser les
vérins sur une surface stable
avant de lever la tour
d’éclairage.
Le fait de se tenir debout sous
une tour d’éclairage et de ses
accessoires alors qu’elle est
abaissée pourrait causer la
mort ou des blessures graves.
Tenir les spectateurs à l’écart
de la tour d’éclairage pendant
qu’on la soulève ou l’abaisse.
DANGER DANGER
Contacting power lines
whenraising light tower will
result in death or serious
injury.
Keep light tower far away
from power lines.
Tenir la tour d’éclairage
éloignée des lignes
électriques.
Le contact avec une ligne
électrique lorsque la tour
d’éclairage est levée
entraînera des blessures
graves ou la mort.
AVERTISSEMENT
WARNING
La manipulation des
luminaires alors qu’ils sont
chauds pourrait causer la mort
ou des blessures graves.
Rester à l’écart des luminaires
lorsqu’ils sont allumés ou
chauds.
Handling light fixtures when
they are hot could result in
death or serious injury.
Keep clear of light
fixtures when illuminated
or hot.
Electrical Info
Part No. 118228
118228
60Hz
120V
15A/20A
Max Amps
Part No. 118250
118250
WARNING - Cancer and
reproductive harm.
www.P65warnings.ca.gov
Part No. 118161
118161
Cancer and Reproductive Harm
www.P65warnings.ca.gov
Cancer et Troubles de l'Appareil
Reproducteur
www.P65warnings.ca.gov
en
English 5
Domestic Models
WARNING - Failure to follow
warnings, instructions and
operator’s manual could result
in death or serious injury. Read
and follow operator’s manual
before operating or servicing this
equipment.
WARNING - Failure to lower tower
into a secured position before
towing could result in death or
serious injury. Lower tower to a
secured position before towing.
WARNING - Excessive towing
speed could result in death or
serious injury. Do not exceed
65mph (105km/h) when towing
trailer.
Part No. 122463
Failure to lower tower into a secured
position before towing could result in
death or serious injury.
Lower tower to a secured position
before towing.
Ne pas abaisser la tour d’éclairage en
position sécurisée au préalable peut
provoquer la mort ou des blessures
graves.
Abaisser la tour en position
sécurisée avant le remorquage.
Excessive towing speed could result
in death or serious injury.
Do not exceed 65mph (105km/h)
when towing trailer.
Une vitesse de remorquage excessive
pourrait entraîner la mort ou de
graves blessures.
Ne pas dépasser 105 km/h (65 mi/h)
lors du remorquage.
Read and follow operator’s manual
before operating or servicing this
equipment.
L’omission de respecter les
avertissements, les instructions et le
manuel de l’utilisateur pourrait entraîner
des blessures graves ou la mort.
Lire et suivre le manuel d’utilisation
avant de faire fonctionner ou de faire
l’entretien de cet équipement.
Failure to follow warnings, instructions,
and operator’s manual could result in
death or serious injury.
122463
International Models
DANGER - Entering electrical
compartment while equipment is
in operation will result in death or
serious injury. Unplug equipment
before entering electrical
compartment.
Part No. 118440
118440
WARNING - Standing under light
tower mast and xtures during
lowering operation could result in
death or serious injury.
Keep bystanders away from light
tower during lowering and raising
operations.
WARNING - Handling light xtures
when they are hot could result in
death or serious injury. Keep clear
of light xtures when illuminated
or hot.
WARNING - Looking at illuminated
light xtures could result in serious
injury. Do not look directly at
illuminated light xtures.
Part No. 118444
118444
WARNING - Failure to follow
warnings, instructions and
operator’s manual could result
in death or serious injury. Read
and follow operator’s manual
before operating or servicing this
equipment.
Part No. 118445
118445
International Models
Electrical Info - 60Hz Models
Part No. 118228
118228
60Hz
120V
15A/20A
Electrical Info - 50Hz Models
Part No. 118474
118474
50Hz
220V
15A
DANGER - Contacting power lines
when raising light tower will result
in death or serious injury. Keep
light tower far away from power
lines.
WARNING - Raising light tower
without positioning outriggers
and lowering jacks could cause
machine rollover resulting in
death or serious injury. Position
outriggers and lower jacks on a
stable surface before raising light
tower.
Part No. 107984
107984
CAUTION - Snow and ice could
cause uncontrolled condition in
winch that could result in minor to
moderate injury. Make sure pawl
engages gear. Apply silicone to
ratchet pawl and spacer.
Part No. 107532
107532
WARNING - Excessive towing
speed could result in death or
serious injury. Do not exceed
65mph (105km/h) when towing
trailer.
Part No. 118110
118110
65 mph (105 km/h) max
WARNING - Failure to lower tower
into a secured position before
towing could result in death or
serious injury. Lower tower to a
secured position before towing.
Part No. 118443
118443
www.allmand.com6
All Models
Tire Information
Part No. 118093 TIRE INFORMATION
SEE OWNER’S
MANUAL FOR
ADDITIONAL
INFORMATION
The weight of cargo should never exceed 90 kg or 200 lbs.
TIRE
FRONT
REAR
SPARE
SIZE
ST 175/80R13B
NONE
NONE
NONE
NONE
241kPa, 35PSI
COLD TIRE PRESSURE
118093
Light Tower Transport Alignment
Part No. 107459
107459
Forklift Pocket
Part No. 107254
107254
Lift Weight
Part No. 122480
122480
Trailer Serial Number (VIN)
Part No. 117746
Operation Icons
The following table contains operation icons that may be
found on the unit, along with the meaning of each icon.
Icon Meaning Icon Meaning
Power On Light Tower
Raise
Power O Light Tower
Lower
Hourmeter Circuit Breaker
Trailer Interior
Light
Disconnecting
Circuit Breaker
Work Light Earth Ground
Features and Controls
The Allmand® Night-Lite™ GR-Series light tower trailer
is intended for use as a stationary lighting device to
illuminate large areas.
Identify the features and controls of the machine by
comparing Figures 1 through 3 with the tables following.
See Operation for detailed information on each feature /
control.
1
F
G
E
CD
BA
H
I
Ref Description
A Tongue Jack
B Safety Chain (2)
C Trailer Coupler
DTrailer Tongue
ELight Tower
F Light Tower Winch Handle (2)
G Light Fixture (4)
H Storage Compartment
I Forklift Pocket / Tie-Down Point (2 each side)
en
English 7
2
J
K
M
N
L
Ref Description
J Lifting Ring
K Control Compartment Cover
L Outrigger / Stabilizer Jack (2)
M Light Tower Mast Rotation Locking Knob
N Light Tower Mast Rotation Handle
3a P
O
Q
3b
P
O
Q
Ref Description
O Power Inlet Panel
P Light Control Panel
QAuxiliary AC Outlets
Preparing the Light Tower
Trailer for Use
WARNING
Operating or towing a machine with worn, damaged
or missing parts could result in death or serious injury.
Replace worn, damaged or missing parts immediately. Do
not operate or tow this machine until all worn, damaged
or missing parts have been replaced, and the machine
operates correctly.
WARNING
Towing a trailer with worn, damaged or underinated tires
could result in death or serious injury. Replace worn or
damaged tires immediately. Keep tires inated to correct
cold tire ination pressure.
NOTICE
The use of authorized replacement Allmand parts is
recommended. The warranty does not cover damage or
performance problems caused by the use of parts that are
not authorized replacement parts.
If the light tower trailer has been stored or not operated
for a period of time, follow these steps to prepare the
Night-Lite™ GR-Series light tower trailer for use.
1. Make sure that a copy of the Operator’s Manual
is with the light tower trailer in the manual storage
container.
2. Make sure that all safety decals are legible and in
place on the light tower trailer. See Safety Decals in
the Operator Safety section.
3. Do a check of the light tower trailer for correct
operation:
A. Make sure that the trailer tongue is locked in
either the park or towing position. See Trailer
Tongue.
www.allmand.com8
B. Use an appropriate means to safely support
the trailer tongue. Make sure that the tongue
jack operates correctly, and that the jack can
be locked in the transport position as well as
the trailer support position. See Operating the
Tongue Jack.
C. Make sure that the outriggers operate correctly,
and that each one is locked in the transport
position. (When initially shipped from the
factory, the outrigger jacks are positioned
toward the front of the machine. The outrigger
jacks should be repositioned toward the rear of
the machine.) See Operating the Outriggers
in the Operation section.
D. Make sure that the winch and cable system
operates correctly, and that the cable is not
frayed or damaged.
E. Make sure that the trailer coupler operates
correctly, and that the trailer coupler is tightly
fastened to the light tower trailer tongue. See
Using The Trailer Coupler.
F. Make sure that the safety chains are tightly
fastened to the light tower trailer tongue,
and that the safety chains and hooks are not
damaged. Replace damaged safety chains and
hooks.
G. Examine the condition and ination pressure of
the tires. See Specications.
4. Make sure that each of the light xtures operate.
See Operating the Tower Lights in the Operation
section.
5. Do a test of the GFCI (if equipped) using the “Test”
button. See Auxiliary AC Outlets in the Operation
section.
Transporting the Light Tower
Trailer
Towing the Light Tower Trailer
Preparing the Light Tower Trailer for Towing
WARNING
Towing a trailer with an underrated tow vehicle or an
underrated or undersized hitch could result in death or
serious injury. Always use a tow vehicle that has a rated
towing capacity that exceeds the Gross Vehicle Weight
Rating (GVWR) of the trailer, and is equipped with the
appropriate size tow hitch rated for the GVWR of the
trailer.
WARNING
Operating or towing a machine with worn, damaged
or missing parts could result in death or serious injury.
Always replace worn, damaged or missing parts promptly.
Do not operate or tow this machine until all worn,
damaged or missing parts have been replaced, and
proper operation of the machine has been veried.
WARNING
Towing a trailer with worn, damaged or underinated tires
could result in death or serious injury. Replace worn or
damaged tires immediately. Keep tires inated to correct
cold tire ination pressure.
1. Shut down the tower lights.
2. Disconnect any power cords from the unit.
3. Fully lower the light tower.
4. Turn the light tower to the transport position, and
tighten the locking knob.
5. Adjust the light xtures to the transport position.
6. Retract the outriggers and stabilizer jacks and lock in
the transport position.
7. Close the control compartment cover and make sure
that it is locked.
8. Lock the trailer tongue in the towing position. See
Trailer Tongue.
9. Make sure that the tow vehicle and trailer hitch
are rated to tow the unit. See Light Tower Trailer
Weight.
Note: Refer to the tow vehicle and trailer hitch
manuals for rated towing capacities.
10. Connect the trailer to the tow vehicle hitch. Examine
the trailer coupler for damage, and make sure that it
is tightly fastened to the tongue. See Connecting the
Light Tower Trailer to the Tow Vehicle.
11. Make sure that the safety chains are tightly fastened
to the trailer tongue, and examine the safety chains
and hooks for damage. Replace as needed.
12. Make sure that the tow vehicle lighting connector will
connect with the trailer lighting connector. Examine
the trailer lighting connector and wires for damage.
Repair or replace as needed.
13. Examine the condition and ination pressure of
the tires. See Checking the Tire Pressure in the
Maintenance section.
14. Remove the wheel chocks from the front and rear of
each wheel.
Trailer Tongue
The light tower trailer tongue can be lifted for storage or
trailer-transporting.
WARNING
Do not try to lift the trailer tongue when the light tower
trailer is connected to a tow vehicle. Death or serious
injury could result.
WARNING
Do not try to lift the trailer tongue unless the front of the
unit is held by the tongue jack. Death or serious injury
could result.
en
English 9
To lift the trailer tongue (park position)
WARNING
Failure to lock the trailer tongue in the park position
could cause the trailer tongue to fall, resulting in death or
serious injury. Always lock the trailer tongue in the park
position.
1. Make sure that the front of the unit is held by the
tongue jack. See Operating the Tongue Jack.
2. Remove the pins (A & B, Figure 4) locking the trailer
tongue (C, Figure 4) in the towing position (D, Figure
4).
3. Lift the trailer tongue to the park position (E, Figure 4).
Install pin (B, Figure 4) into the park position locking
hole (F, Figure 4). Return pin (A, Figure 4) into its
original hole. Lock each pin with its retainer hook.
To lift the trailer tongue (park position)
WARNING
Failure to lock the trailer tongue in the towing position
could cause the front of the light tower trailer to fall,
resulting in death or serious injury. Always lock the trailer
tongue in the towing position.
1. Make sure that the front of the unit is held by the
tongue jack. See Operating the Tongue Jack.
2. Remove the pin locking the trailer tongue in the park
position (F, Figure 4). Also remove pin (A, Figure 4).
3. Lower the trailer tongue to the towing position (D,
Figure 4). Install pins (A, Figure 4) and (B, Figure 4).
Lock each pin with its retainer hook.
4
C
D
F
BAE
Connecting the Light Tower Trailer to the
Tow Vehicle
WARNING
Retracting the tongue jack without supporting the trailer
tongue could result in death or serious injury. Make sure
that the trailer tongue is safely supported by appropriate
means before you retract the tongue jack.
1. Put wheel chocks (not supplied) against the front and
back of each wheel on both sides of the light tower
trailer.
2. Make sure that the trailer tongue is lowered and
locked in the towing position. See Trailer Tongue.
3. Use the tongue jack to lift the trailer coupler above the
tow vehicle’s hitch ball. See Operating the Tongue
Jack.
4. Move the tow vehicle so that the hitch ball is under
the trailer coupler.
5. Lower the trailer coupler onto the hitch ball with the
tongue jack.
6. Lock the trailer coupler. See Using the Trailer
Coupler.
7. Attach the safety chains (A, Figure 5) to the tow
vehicle’s hitch frame. Cross the chains under the
tongue as shown. Leave enough slack in the chains
to allow for turns, but not so much that the chains will
hit the road surface.
8. Connect the trailer lighting connector (B, Figure 5)
to the tow vehicle lighting connector. Make sure that
the trailer lighting harness has sucient length to not
disconnect when turning, but not so much length that
the harness will hit the road surface. Once connected,
check the stop, turn signal, tail, side marker and
license plate lights for correct operation.
9. Fully lift the tongue jack foot, then retract the tongue
jack into the transport position. See Operating the
Tongue Jack.
10. Remove the wheel chocks from both sides of the light
tower trailer wheels.
5
A
B
www.allmand.com10
Operating the Tongue Jack
The unit is equipped with a tongue jack to support the
front of the light tower trailer and to level the trailer front-
to-rear.
To deploy the tongue jack
WARNING
Failure to secure the tongue jack in the operating position
with the jack locking pin could cause the front of the light
tower trailer to collapse, resulting in death or serious
injury. Always be sure to secure the tongue jack in the
operating position with the jack locking pin.
1. Remove the jack locking pin (A, Figure 6), rotate the
tongue jack into the operating position (B, Figure 6),
and install the jack locking pin fully through the top
and bottom holes in the jack and tongue.
2. Unfold the crank handle (C, Figure 6).
To lower the tongue jack foot (raise the front of the
trailer)
• Turn the jack handle clockwise (D, Figure 6) to lower
the jack foot (E, Figure 6) and raise the front of the
light tower trailer.
To raise the tongue jack foot (lower the front of the
trailer)
• Turn the jack handle counter-clockwise (F, Figure 6)
to raise the jack foot (G, Figure 6) and lower the front
of the light tower trailer.
To retract the tongue jack
WARNING
Retracting the tongue jack without supporting the trailer
tongue could result in death or serious injury. Always be
sure the trailer tongue is safely supported by appropriate
means prior to retracting the tongue jack.
1. Be sure the trailer tongue is secured in the towing
position. See Trailer Tongue.
2. Use an appropriate means to support the trailer
tongue.
3. Fully raise the tongue jack foot.
4. Fold the crank handle (H, Figure 6).
5. Remove the jack locking pin (A, Figure 6), rotate the
jack into the transport position (I), and install the jack
locking pin fully through the top and bottom holes in
the jack and trailer tongue.
6
C
DF
B
A
E
I
G
B
Using the Trailer Coupler / Lunette Eye
The trailer comes standard with a trailer coupler for a ball
hitch. There is also an optional lunette eye for a pintle
hitch or a reversible trailer hitch bar, with a trailer coupler
for a ball hitch, and a lunette eye for a pintle hitch.
To use the trailer coupler (standard)
• See Trailer Coupler.
To use the lunette eye (optional)
• See Lunette Eye.
To change between the trailer coupler and lunette eye
(optional reversible trailer hitch bar)
WARNING
Failure to use new, correctly tightened nylock nuts to
attach the hitch bar to the trailer tongue could result
in death or serious injury. Always use new, properly
tightened nylock nuts when attaching the hitch bar to the
trailer tongue.
1. Remove the hardware (A, Figure 7) attaching the
trailer hitch bar to the trailer tongue. Discard the
nylock nuts.
2. Turn the trailer hitch bar so either the trailer coupler
(B, Figure 7) or lunette eye (C, Figure 7) is facing
forward. Install the hardware removed in Step 1 into
the set of holes in the trailer tongue, using new nylock
nuts. Tighten to 110 lb-ft (149 Nm).
en
English 11
7
C
A
B
Trailer Coupler
To connect the trailer to the tow vehicle
1. Lift up and pull back on the locking latch (A, Figure 8)
of the trailer coupler.
2. Lower the trailer coupler onto the vehicle ball hitch.
Make sure that the hitch ball (B, Figure 8) is fully
engaged in the coupler socket (C, Figure 8).
3. Push the locking latch forward and down. (It is self-
locking.) Install a padlock through the latch hole (D,
Figure 8) for added security.
4. Make sure that the coupler is fully installed on the ball
hitch.
To disconnect the trailer from the tow vehicle
1. Remove the padlock (if installed) from the trailer
coupler latch (D, Figure 8).
2. Lift the trailer coupler (A, Figure 8) latch up and back.
8
A
D
C
B
Lunette Eye
To connect the trailer to the tow vehicle
1. Remove the locking pin (A, Figure 9, if equipped) from
the pintle hitch (B, Figure 9).
2. Pull up on the latch (C, Figure 9), to open the pintle
hitch.
3. Lower the lunette eye (D, Figure 9) into the pintle
hook (E, Figure 9).
4. Close the pintle hitch. Make sure that the latch locks
the pintle hitch in place.
5. Install the locking pin (if equipped).
To disconnect the trailer from the tow vehicle
1. Remove the locking pin (if equipped) from the pintle
hitch.
2. Pull up on the latch to open the pintle hitch.
3. Remove the lunette eye from the pintle hook.
9
C
D
A
B
E
Light Tower Trailer Weight
WARNING
Towing the light tower trailer when it is loaded beyond
the Gross Vehicle Weight Rating (GVWR) could result in
death or serious injury. Always maintain a gross vehicle
weight less than the GVWR stated on the serial plate and
in the Specications section of this manual.
The light tower trailer is an SAE Class 2 trailer, with a
Gross Vehicle Weight Rating (GVWR) as stated on the
serial plate and in the Specications section of this
manual. Do not exceed the GVWR by attempting to carry
additional tools or equipment. Do not carry riders. See
Safety.
www.allmand.com12
Towing the Light Tower Trailer
WARNING
Excessive speed when towing the trailer could result in
death or serious injury. Always maintain a safe towing
speed for road conditions. Never exceed 65 MPH (105
km/h) when towing the trailer.
WARNING
Rollover Hazard
Do not make sharp turns at high speeds when towing the
light tower trailer. This could cause the light tower trailer
to roll over, resulting in death, serious injury, or equipment
damage.
The rated maximum highway towing speed for the light
tower trailer is 65 MPH (105 km/h). Be sure to check your
state or province laws regarding maximum legal towing
speeds for trailers.
When towing the trailer o-highway or on rougher terrain,
the maximum towing speed is 20 MPH (32 km/h). Slower
speeds may be required for very rough terrain.
Tow the light tower trailer with the engine and lights shut
down.
Do not carry riders.
Disconnecting the Light Tower Trailer from
the Tow Vehicle
WARNING
Crush Hazard
Attempting to move the light tower trailer by manually
pushing or pulling it could present a crush hazard
resulting in death or serious injury. Always move the trailer
withthe tow vehicle, put chocks against the wheels, and
lower the tongue jack before uncoupling the trailer from
the tow vehicle.
1. Find a rm, level and stable surface at the work site.
See Work Site Considerations in the Operation
section.
2. Move the light tower trailer into the desired position
with the tow vehicle.
3. Put chocks against the wheels on both sides of the
trailer.
4. Disconnect the trailer lighting connector from the tow
vehicle lighting connector.
5. Move the tongue jack into the operating position. See
Operating the Tongue Jack.
6. Lower the tongue jack foot to support the front of the
light tower trailer. See Operating the Tongue Jack.
7. Disconnect the trailer coupler from the tow vehicle.
See Using the Trailer Coupler.
8. Use the tongue jack to raise the trailer coupler above
the tow vehicle’s hitch ball.
9. Disconnect the safety chains from the tow vehicle’s
hitch frame.
10. Move the tow vehicle clear of the light tower trailer.
11. If desired, move the trailer tongue up to the park
position. See Trailer Tongue.
Transporting on a Trailer
The forklift pockets on either side of the unit can be used
as tie-down points. See Lifting the Light Tower Trailer
for forklift pocket locations.
Always fasten the light tower trailer to the transporting
trailer with chains or straps. Do not apply more than 600
pounds (272 kg) force on the chains or straps.
The truck operator is responsible for making sure the unit
is safely loaded and fastened to his transporting trailer.
Note: When transporting on a trailer, turn the light xtures
to the rear of the unit. See Figure 10.
10
Lifting the Light Tower Trailer
WARNING
Lifting the light tower trailer with a lifting device that is
underrated or damaged could result in death or serious
injury. Always make sure that the lifting device is rated to
lift the weight of the light tower trailer. Make sure that the
lifting device is in good condition before lifting.
WARNING
Standing or walking under equipment when it is lifted
could result in death or serious injury. When lifting the
light tower trailer, always keep clear of the area around
and under the light tower trailer, and do not let others in
the area.
en
English 13
General Lifting Guidelines
• Before lifting, lower the light tower and shut down the
engine. See Pre-Transport Check List.
• Make sure that the lifting device you are using is in
good condition and rated to exceed the Gross Vehicle
Weight Rating (GVWR) of the light tower trailer. See
Light Tower Trailer Weight.
• Use aid when using a forklift, crane or hoist, and
when unloading.
• Use only the lifting eye to lift the unit with a hoist or
crane.
• Use only shackles or a locking-type hook when lifting.
• Do not stand or walk under the unit when it is lifted.
Keep others away.
Lifting Eye
The light tower trailer has one lifting eye, located at the
top center of the unit (A, Figure 11). Use only this lifting
eye to lift the light tower trailer.
Use a lifting device with a lift rating that exceeds the
Gross Vehicle Weight Rating (GVWR) of the light tower
trailer. See Light Tower Trailer Weight.
The lifting eye is rated for 1500 pounds (680 kg), and is
designed to hold the weight of the light tower trailer only.
Do not add any more weight to the unit when lifting.
Do not keep the light tower trailer lifted for long periods of
time.
11
A
Lifting the Light Tower Trailer with a Forklift
The light tower trailer has two forklift pockets (A, Figure
12) on either side of the unit.
Use a forklift with a rated lifting capacity greater than the
weight of the light tower trailer. See Light Tower Trailer
Weight.
12
A
Operation
Work Site Safety Considerations
It is the operator’s responsibility to make sure that the
light tower trailer is properly and safely positioned at the
work site. Follow state, province and federal rules, as well
as rules or instructions for the work site.
Overhead Clearance
DANGER
Electrocution Hazard
• Raising the light tower in the presence of electrical
power lines will result in death or serious injury.
Always check overhead wires and obstructions before
raising or lowering the light tower.
• Always follow the rules or regulations for your
worksite, and state, province and national electric
code for maintaining a safe distance from overhead
wires.
The work site must be clear of overhead obstructions
such as power lines, trees, etc. Keep in mind the
maximum height of the light tower when fully raised. See
Specications.
www.allmand.com14
Ground Surface
WARNING
Rollover Hazard
Positioning the light tower trailer on soft, unstable or
unlevel ground could cause trailer rollover, resulting in
death or serious injury. Always position the trailer on a
rm, level and stable surface and deploy the outriggers
before raising the light tower.
• Do not set up the light tower trailer on an incline of
more than 2.8° (5% grade) front-to-back and side-to-
side.
• Do not set up the light tower trailer on unlevel or
unstable ground. Set up on smooth, at and solid
ground surfaces only.
Wind
WARNING
Rollover Hazard
Operating with the light tower raised in winds exceeding
50 mph (80 km/h) could cause trailer tip-over resulting in
death or serious injury. Do not operate with the light tower
raised in winds exceeding 50 mph (80 km/h).
When the light tower is in the operating position it is
located in the middle of a three-point outrigger system
for optimum balance and stability. This system was
engineered to allow the light tower to remain operational
in sustained winds of 50 mph (80 km/h) with the light
tower extended to full height and the outriggers in position
on a rm, level surface.
Leveling and Stabilizing the Light
Tower Trailer
WARNING
Rollover Hazard
Setting up the light tower trailer on soft, unstable or
unlevel ground could cause trailer rollover, resulting in
death or serious injury. Always set the trailer on a rm,
level and stable surface and deploy the outriggers before
raising the light tower.
1. Set the light tower trailer on a solid, level work site.
See Work Site Safety Considerations.
2. Put wheels chocks against the front and rear of each
wheel (A, Figure 13).
13
A
3. Make the light tower trailer level using the tongue
jack. See Operating the Tongue Jack in the
Transporting section.
4. Deploy the outriggers. See Operating the
Outriggers.
5. Make the light tower trailer level front to back and side
to side using the jacks.
Operating the Outriggers
The unit has left and right outriggers at the rear of the
machine.
WARNING
Rollover Hazard
• Failure to deploy the outriggers before raising the light
tower could cause the light tower trailer to tip over,
resulting in death or serious injury. Always deploy the
outriggers before raising the light tower.
• Failure to lock the stabilizer jack in the operating
position could cause the back of the light tower trailer
to fall, resulting in death or serious injury. Always be
sure to lock the stabilizer jack in the operating position
with the jack locking pin.
• Stabilizer jacks must be supported by a at, level solid
ground surface.
To deploy the outriggers:
1. Pull the outrigger locking pin (A, Figure 14).
2. Move the outrigger (B, Figure 14) out until the pin
locks the outrigger in the operating position.
Note: When initially shipped from the factory, the
outrigger jacks are toward the front of the machine
(not shown) for shipping purposes. They should be
toward the rear of the machine as shown in Figure 14.
Move the outrigger completely out, turn the outrigger
so the jack is toward the rear of the machine, and
install, making sure that the pin locks the outrigger in
the operating position.
en
English 15
3. Remove the stabilizer jack locking pin (C, Figure 14),
turn the jack into the operating position (D, Figure 14),
and install the stabilizer jack locking pin fully through
the top and bottom holes in the jack and outrigger.
4. Unfold the handle (E, Figure 15) of the stabilizer jack,
then turn clockwise (F, Figure 15) to lower the jack
foot (G, Figure 15) until rmly planted on the work site
surface.
5. Repeat for the opposite outrigger and stabilizer jack.
To retract the outriggers:
1. Fully lift the stabilizer jack foot by turning the jack
handle counterclockwise.
2. Fold the handle.
3. Remove the stabilizer jack locking pin, turn the jack
into the transport position, and install the stabilizer
jack locking pin fully through the top and bottom holes
in the jack and outrigger.
4. Pull the outrigger locking pin, and move the outrigger
in until the pin locks the outrigger in the transport
position.
5. Do the same for the other stabilizer jack and
outrigger.
14
B
A
C
D
15
G
F
E
Preparing to Operate the Unit
Domestic Models
1. Make sure that the light tower trailer is level front to
back and side to side. See Leveling and Stabilizing
the Light Tower Trailer.
2. Open the control compartment cover.
3. Determine the mode of operation: Stand-Alone or
Chained.
Stand-Alone:
• For stand-alone operation, a single NLGR-
Series Chain unit can be powered using either
the NEMA 5-15P inlet (A, Figure 16) or NEMA
L5- 20P inlet (B, Figure 16).
• Use an appropriately sized power cord (not
supplied) as noted in the following table. Route
the cord through the access hole (C, Figure 16).
• Use the selector switch (D, Figure 16) located
between the inlets to select either the 5-15P or
L5-20P inlet. Make sure that the circuit breaker
(E or F, Figure 16) for that power inlet is in the
‘ON’ position.
Chained:
• For chained operation, two NLGR-Series Chain
units can be powered by a single power source.
The rst unit must use the NEMA L5-20P inlet
(B, Figure 16) to connect to the power source.
The second unit must use the NEMA 5-15P
inlet (A, Figure 16) to connect to the rst unit’s
5-15R outlet (G, Figure 16).
• Use an appropriately sized power cord (not
supplied) for both units as noted in the following
table. Route the cord through the access hole
(C, Figure 16).
www.allmand.com16
• The inlet selector switch (D, Figure 16) must be
switched to the L5-20P inlet (B, Figure 16) on
the rst unit and the 5-15P inlet (A, Figure 16)
on the second unit. Make sure that the circuit
breaker (E or F, Figure 16) for that power inlet is
in the ‘ON’ position.
16
C
A
E D F
B G
Power Cord Size Requirements
Stand-Alone Operation
Plug: 5-15P or L5-20P
Cord Length Cord Size
Imperial Metric Imperial Metric
0-100 ft 0-30.5 m 16/3 1.31 mm²
101-150 ft 30.8-45.7 m 12/3 3.31 mm²
151-250 ft 46.0-76.2 m 10/3 5.26 mm²
Chained Operation
First Unit (connected to power source)
Plug: L5-20P
Cord Length Cord Size
Imperial Metric Imperial Metric
0-50 ft 0-15.2 m 12/3 3.31 mm²
51-100 ft 15.5-30.5 m 10/3 5.26 mm²
Second Unit (powered by rst unit)
Plug: 5-15P
Cord Length Cord Size
Imperial Metric Imperial Metric
0-100 ft 0-30.5 m 16/3 1.31 mm²
101-150 ft 30.8-45.7 m 12/3 3.31 mm²
151-250 ft 46.0-76.2 m 10/3 5.26 mm²
International Models
1. Make sure that the light tower trailer is level front to
back and side to side. See Leveling and Stabilizing
the Light Tower Trailer.
2. Open the control compartment cover.
3. Determine the mode of operation: Stand-Alone or
Chained.
Stand-Alone:
• For stand-alone operation, a single NLGR-
Series Chain unit can be powered using the
IEC 60309 (6H) inlet (A, Figure 17).
• Use an appropriately sized power cord (not
supplied) as noted in the following table. Route
the cord through the access hole (B, Figure 17).
• Make sure that the circuit breaker (C, Figure
17) for that power inlet is in the ‘ON’ position.
Chained:
• For chained operation, up to three NLGR-
Series Chain units can be powered by a single
power source. The rst unit must use the IEC
60309 (6H) inlet (A, Figure 17) to connect to the
power source. The second unit must use the
IEC 60309 (6H) inlet (A, Figure 17) to connect
to the rst unit’s IEC 60309 (6H) outlet (D,
Figure 17). If using a third unit, the third unit
must use the IEC 60309 (6H) inlet (A, Figure
17) to connect to the second unit’s IEC 60309
(6H) outlet (D, Figure 17).
• Use an appropriately sized power cord (not
supplied) depending on the amount of units
used as noted in the following table. Route the
cord through the access hole (B, Figure 17).
• Make sure that the circuit breaker (C, Figure
17) for that power inlet is in the ‘ON’ position.
17
C
A D
B
Power Cord Size Requirements
Stand-Alone Operation
Plug: IEC 60309 (6H)
Cord Length Cord Size
Imperial Metric Imperial Metric
0-250 ft 0-76.2 m 16/3 1.31 mm²
251-600 ft 76.5-182.9 m 12/3 3.31 mm²
601-1000 ft 183.2-304.8 m 10/3 5.26 mm²
en
English 17
Chained Operation (two units)
First Unit (connected to power source)
Plug: IEC 60309 (6H)
Cord Length Cord Size
Imperial Metric Imperial Metric
0-50 ft 0-15.2 m 16/3 1.31 mm²
51-150 ft 15.5-45.7 m 12/3 3.31 mm²
151-250 ft 46.0-76.2 m 10/3 5.26 mm²
Second Unit (powered by rst unit)
Plug: IEC 60309 (6H)
Cord Length Cord Size
Imperial Metric Imperial Metric
0-125 ft 0-38.1 m 16/3 1.31 mm²
126-300 ft 38.4-91.4 m 12/3 3.31 mm²
301-500 ft 91.7-152.4 m 10/3 5.26 mm²
Chained Operation (three units)
First Unit (connected to power source)
Plug: IEC 60309 (6H)
Cord Length Cord Size
Imperial Metric Imperial Metric
0-50 ft 0-15.2 m 12/3 3.31 mm²
51-100 ft 15.5-30.5 m 10/3 5.26 mm²
Chained Operation (three units)
Second Unit (powered by rst unit)
Plug: IEC 60309 (6H)
Cord Length Cord Size
Imperial Metric Imperial Metric
0-75 ft 0-22.9 m 12/3 3.31 mm²
76-150 ft 23.2-45.7 m 10/3 5.26 mm²
Third Unit (powered by second unit)
Plug: IEC 60309 (6H)
Cord Length Cord Size
Imperial Metric Imperial Metric
0-75 ft 0-22.9 m 16/3 1.31 mm²
76-200 ft 23.2-61.0 m 12/3 3.31 mm²
201-300 ft 61.3-91.4 m 10/3 5.26 mm²
Light Tower Operation
Adjusting the Lights
Adjusting The Light Fixtures
Note: The light xtures must be adjusted before raising
the light tower.
1. Adjust each xture to the desired position. To adjust
left and right, move the xture yoke (A, Figure 18).
To adjust up and down, loosen the locking knob (B,
Figure 18), adjust the xture, then tighten the locking
knob.
2. When lighting operations are complete, adjust the
light xtures to the transport position, with the xtures
facing straight back toward the rear of the light tower
trailer. See Transporting the Light Tower Trailer.
18
B
A
Rotating The Light Tower
WARNING
Failure to tighten the light tower locking knob may cause
the light xtures to swing inadvertently, especially in windy
conditions or during transport, and could result in death
or serious injury. Always tighten the tower locking knob
securely after turning the light tower.
CAUTION
Rotating the light tower will cause the light xtures to
swing, and could result in minor to moderate injury. Be
careful to rotate the tower slowly, and be aware of the
light xtures while rotating the tower.
1. Loosen the light tower rotation locking knob (A, Figure
19).
2. Use the handles (B, Figure 19) to rotate the light
tower in the desired direction.
3. Tighten the light tower locking knob.
4. When lighting operations are complete, rotate the light
tower to the transport position, with the xtures facing
straight back toward the rear of the light tower trailer.
Tighten the light tower rotation locking knob.
www.allmand.com18
19
B
A
Raising and Lowering the Light Tower
DANGER
Electrocution Hazard
Raising the light tower in the presence of electrical
power lines will result in death or serious injury. Always
check overhead wires and obstructions before raising or
lowering the light tower.
WARNING
Rollover Hazard
Before raising, lowering or operating the tower lights,
the trailer must be set up, leveled and stabilized. See
Leveling and Stabilizing the Light Tower.
WARNING
Crush Hazard
Standing under the light tower while raising or lowering
could result in death or serious injury. Make sure that
there are no persons near the light tower when raising or
lowering the light tower.
Raising the Light Tower
1. Before raising the light tower, adjust the tower lights to
the desired work position. See Adjusting the Lights.
2. Turn the winch handles (A, Figure 20) until the tower
is fully raised. Do not overturn the handles.
Lowering the Light Tower
1. Turn the winch handles (A, Figure 20) until the tower
is fully lowered. Do not overturn the handles.
20
A
Operating the Tower Lights
WARNING
Optical Hazard
Looking at illuminated light xtures could result in serious
injury. Never look directly at illuminated light xtures.
Turning the Lights On
1. Unlock and open the control compartment cover.
2. Turn the circuit breaker for the chosen power inlet to
the ON position. See Preparing to Operate the Unit.
3. Select the preferred mode of operation: Timer /
Manual or Photocell. See Light Operation Mode.
4. Turn the individual light switches (A, Figure 21) (1-4)
to the ON position (if set to OFF).
Note: If the mode of operation is set to Photocell or Timer,
the lights will not turn on until dark (Photocell) or until the
time selected (Timer).
Turning the Lights O
• If in Manual mode, turn Manual mode o. See Light
Operation Mode.
• If in Photocell or Timer mode, the lights will turn o
automatically in ambient light (Photocell) or at the
time selected (Timer).
en
English 19
21
A
Light Operation Mode
The tower lights can be controlled manually, by photocell,
or by timer.
Manual Operation
1. Turn the Photocell / Timer switch (A, Figure 22) to the
TIMER position.
2. Push the MANUAL button (B, Figure 23) on the timer
module to until the black bar in the display window
(C, Figure 23) is positioned above ‘ON’ to turn the
lights on. Push the button twice to move the black bar
above ‘OFF’ to turn the lights o.
Photocell Operation
Turn the Photocell / Timer switch (A, Figure 22) to the
PHOTOCELL position. The lights will automatically come
on in the absence of ambient light.
Note: For most consistent operation, avoid locating the
unit in a shadowed area, and orient the unit so the control
box faces north.
Timer Operation
Your machine is equipped with a 7 day, 16 event
programmable timer module. The timer allows for full
on/o control of the light tower, and can be turned on
and o at specc times of the day. The timer can also
be programmed for a specic day of the week or any
combination of days.
Turn the Photocell / Timer switch (A, Figure 22) to the
TIMER position.
To set the timer:
1. Reset the timer module (rst time use):
a. With a blunt object press the ℗ button (D,
Figure 23). The timer display window (C, Figure
23) will ash.
2. Set the day and time:
a. Press the CLOCK button (E, Figure 23) and
continue to hold during the following steps.
b. Set the day of the week by pressing the DAY
button (F, Figure 23) until the correct day
appears.
c. Set the hour by pressing the HOUR button (G,
Figure 23) until the desired hour appears.
d. Set the minutes by pressing the MIN button (H,
Figure 23) until the desired minutes appear.
e. Release the CLOCK button (E, Figure 23) after
the day and time have been set.
3. Programming the timer:
a. Press the TIMER (I, Figure 23) button to enter
the program mode to set the ‘ON’ event.
Note: The program will show event ‘1 ON’ in the
display screen.
b. Press the DAY button (F, Figure 23) to select
the desired day or group of days the unit will
turn on.
c. Press the HOUR and MIN buttons (G and H,
Figure 23) to set the desired time the unit will
turn on.
d. Press the TIMER button (I, Figure 23) again to
set the ‘OFF’ event.
Note: The program will show event ‘1 OFF’ in
the display screen.
e. Press the DAY button (F, Figure 23) to select
desired day or group of days the unit will turn
o.
Note: The selected day or group of days must
be consistent between event ‘1 ON and 1 OFF’
in order for the programming to work properly.
f. Press the HOUR and MIN buttons (G and H,
Figure 23) to set the desired time the unit will
turn o.
g. To set another event, repeat programming
procedure steps a. through f.
Note: There are up to 16 programable ON/OFF
events available on this timer.
h. To nish programing, press the CLOCK
button (E, Figure 23) and the timer shall start
executing the set programming.
4. Timer on/o:
• Push the MANUAL button (B, Figure 23) on the
timer module to until the black bar in the display
window (C, Figure 23) is positioned above
AUTO to turn the timer programming on. Push
the button until the black bar moves above OFF
to turn the timer programming o.
22
A
x
www.allmand.com20
ON AUTO OFF ℗
ON
x
ON
Mo Tu We Th Fr Sa Su
23
F G
H
D
B
I
E
C
Auxiliary AC Outlet
An auxiliary AC outlet (B, Figure 24a-b) is located to the
right of the power inlet panel. The outlet is protected by a
spring-loaded cover.
Note: Outlets may dier according to model.
Power is supplied to the outlet only when the unit is
connected to an external power source. See Preparing to
Operate the Unit.
If a Breaker Trips
1. Disconnect the load from the outlet.
2. Remove the input power.
3. Correct the load problem.
4. Plug in the input power.
5. Reset the breaker.
Note: Be sure to also check the GFCI breaker on the
GFCI outlet (if equipped), and reset if necessary.
6. Reconnect the load.
7. If the problem persists, see Troubleshooting.
24a
A
24b
A
Unit Shutdown
WARNING
Do not remove the wheel chocks from the front and back
of the wheels until the light tower trailer is connected to
the tow vehicle and ready to be transported. Doing so
could result in death or serious injury.
Once lighting operations are complete at the work site,
shut down the unit:
1. Turn o the lights. See Operating the Tower Lights.
2. Wait 10 minutes for the lights to cool.
3. Lower the light tower. See Raising And Lowering
the Light Tower.
4. Rotate the light tower to the transport position. See
Adjusting the Lights.
5. Adjust the light xtures to the transport position. See
Adjusting the Lights.
6. Make sure the control compartment cover is closed
and locked.
7. Retract the outriggers. See Leveling and Stabilizing
the Light Tower Trailer.
8. The unit is now ready for transport. See
Transporting.
Maintenance
WARNING
Operating or towing a machine with worn, damaged
or missing parts could result in death or serious injury.
Replace worn, damaged or missing parts immediately. Do
not operate or tow this machine until all worn, damaged
or missing parts have been replaced, and the machine
operates correctly.
Before you do maintenance, see Safety.
Correct maintenance of the equipment is important for
safe operation. Use the following maintenance procedures
in addition to those scheduled by your shop equipment
maintenance schedule.
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
Allmand Night-Lite Chain Le manuel du propriétaire
- Taper
- Le manuel du propriétaire
- Ce manuel convient également à
dans d''autres langues
Documents connexes
-
Allmand NL GR-Series Liquid-Cooled 6kW Ops Le manuel du propriétaire
-
Allmand NLPV2 Manuel utilisateur
-
-
-
-
-
-
-
-