Transition Networks C/E-TBT-FRL-04(LH) Manuel utilisateur
- Catégorie
- Convertisseurs de média réseau
- Taper
- Manuel utilisateur
Ce manuel convient également à
COMPLIANCE INFORMATION
UL Listed
C-UL Listed (Canada)
CISPR/EN55022 Class A
FCC Regulations
This equipment has been tested and found to comply with the limits for a class A digital device, pursuant
to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference, in which case the user will be
required to correct the interference at the user’s own expense.
Canadian Regulations
This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus set out on
the radio interference regulations of the Canadian Department of Communications.
Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les limites applicables
aux appareils numériques de la class A prescrites dans le Règlement sur le brouillage radioélectrique
édicté par le ministère des Communications du Canada.
European Regulations
Warning
This is a Class A product. In a domestic environment this product may cause radio interference in which
case the user may be required to take adequate measures.
Achtung !
Dieses ist ein Gerät der Funkstörgrenzwertklasse A. In Wohnbereichen können bei Betrieb dieses Gerätes
Rundfunkstörungen auftreten, in weichen Fällen der Benutzer für entsprechende Gegenmaßnahmen
werantwortlich ist.
Attention !
Ceci est un produit de Classe A. Dans un environment domestique, ce produit risque de créer des
interférences radioélectriques, il appartiendra alors à l’utilsateur de prende les measures spécifiques
appropriées
Copyright Restrictions
© 1999-2001 TRANSITION Networks.
All rights reserved. No part of this work may be reproduced or used in any form or by any means –
graphic, electronic, or mechanical – without written permission from TRANSITION Networks.
Trademark Notice
All registered trademarks and trademarks are the property of their respective owners.
Printed in the U.S.A. 33137.E
The TRANSITION Networks C/E-TBT-FRL-04
10BASE-T/10BASE-FL media converters, designed
to be installed in the E-MCC-1600 Media
Conversion Center, connect either half-duplex or
full-duplex, unshielded or shielded 10BASE-T
twisted-pair copper to either half-duplex or full-
duplex 10BASE-FL singlemode or multimode fiber.
CAUTION: RJ connectors are NOT INTENDED FOR CONNECTION TO THE
PUBLIC TELEPHONE NETWORK. Failure to observe this caution could result in
damage to the public telephone network.
Der Anschluss dieses Gerätes an ein öffentlickes Telekommunikationsnetz in den EG-Mitgliedstaaten
verstösst gegen die jeweligen einzelstaatlichen Gesetze zur Anwendung der Richtlinie 91/263/EWG zur
Angleichung der Rechtsvorschriften der Mitgliedstaaten über Telekommunikationsendeinrichtungen
einschliesslich der gegenseitigen Anerkennung ihrer Konformität.
Minneapolis, MN 55344 USA
10BASE-T/10BASE-FL
Slide-In-Module Media Converters
C/E-TBT-FRL-04, C/E-TBT-FRL-04(SC), C/E-TBT-FRL-04(SM), C/E-TBT-FRL-04(L),
C/E-TBT-FRL-04(MT), C/E-TBT-FRL-04(LH), C/E-TBT-FRL-04(XC)
USER’S GUIDE
C/E-TBT-FRL-04
Provides an RJ-45 unshielded twisted
pair 10BASE-T connector and a set of
RX (receive) and TX (transmit) ST
10BASE-FL 850nm multimode fiber
connectors.
C/E-TBT-FRL-04 (SC)
Provides an RJ-45 unshielded twisted
pair 10BASE-T connector and a set of
RX (receive) and TX (transmit) SC
10BASE-FL 850nm multimode fiber
connectors.
C/E-TBT-FRL-04(SM)
Provides an RJ-45 unshielded twisted
pair 10BASE-T connector and an RX
(receive) and TX (transmit) ST 10BASE-
FL 1300nm singlemode fiber
connector.
C/E-TBT-FRL-04(L)
Provides an RJ-45 unshielded twisted
pair 10BASE-T connector and a set of
RX (receive) and TX (transmit) ST
10BASE-FL 1300nm multimode fiber
connectors.
C/E-TBT-FRL-04(MT)
Provides an RJ-45 unshielded twisted
pair 10BASE-T connector and an RX
(receive) and TX (transmit) MT-RJ
10BASE-FL 850nm multimode fiber
connector.
C/E-TBT-FRL-04(LH)
Provides an RJ-45 unshielded twisted
pair 10BASE-T connector and a set of
RX (receive) and TX (transmit) ST
10BASE-FL 1300nm singlemode fiber
connectors.
C/E-TBT-FRL-04(XC)
Provides an RJ-45 unshielded twisted
pair 10BASE-T connector and an RX
(receive) and TX (transmit) SC 10BASE-
FL 1300nm singlemode fiber
connector.
C/E-TBT-FRL-04 in the Network .2
Installation . . . . . . . . . . . . . . . . .3
Operation . . . . . . . . . . . . . . . . . .4
Fault Isolation and Correction . .5
Cable Specifications . . . . . . . . . .6
Technical Specifications . . . . . . .7
Compliance Information . . . . . . .8
Power Modules
Media
Conversion
Center
Power
In Use
Power
In Use
1
2
Management
Module
Power
Link
TX
RX
C/E-TBT-FRL-04 IN THE NETWORK
Use the C/E-TBT-FRL-04 media converter (or two C/E-TBT-FRL-04 media
converters in pairs) to connect a workstation to a remote hub or to connect two
hubs, switches, or workstations.
NOTE: Maximum Number of Nodes: 2 nodes
The AutoCross™ feature allows either straight-through or crossover cables to be
used when connecting to 10BASE-T devices, such as hubs, transceivers, or
network interface cards (NICs). AutoCross™ determines the characteristics of
the cable connection and automatically configures the unit to link up to straight-
through or to crossover cable.
The LinkALERT™ feature allows the C/E-TBT-FRL-04 media converter to pass
10BASE-T side link faults to the 10BASE-FL side and to pass 10BASE-FL side link
faults to the 10BASE-T side. NOTE: An enable/disable switch allows the network
administrator to disable LinkALERT™ in the case of a network with back-to-
back media converter installation in which Autonegotiation from other sources
does not work properly.
TECHNICAL SPECIFICATIONS
Standards IEEE 802.3
Dimensions 4.7" x 3.0" x 1.0" (119 mm x 76 mm x 25 mm)
Environment Temperature 0 to 50°C (32° to 122° F )
Storage Temperature -20 to 85°C
Humidity 5-95%, non condensing
Altitude 0-10,000 feet
Warranty Lifetime
DECLARATION OF CONFORMITY
Name of Mfg: Transition Networks
6475 City West Parkway, Minneapolis MN 55344 USA
Model: C/E-TBT-FRL-04 Series 10BASE-T/10BASE-FL Media Converter
Part Number: C/E-TBT-FRL-04, C/E-TBT-FRL-04(SC), C/E-TBT-FRL-04(SM), C/E-TBT-FRL-04(L),
C/E-TBT-FRL-04(MT), C/E-TBT-FRL-04(LH), C/E-TBT-FRL-04(XC)
Regulation: EMC Directive 89/336/EEC
Purpose: To declare that the C/E-TBT-FRL-04 to which this declaration refers is
in conformity with the following standards.
EMC-CISPR 22: 1985 Class A; EN 55022: 1988 Class A; EN 50082-1:1992;
EN 60950 A4:1997; IEC 801.2, IEC 801.3, and IEC 801.4; IEC 950
I, the undersigned, hereby declare that the equipment specified above conforms to the
above Directive(s) and Standard(s).
_July 7, 1999_____
Stephen Anderson, Vice-President of Engineering Date
2 kilometers - 850 nM multimode
100 meters
100 meters
20 kilometers - 1300 nM singlemode
5 kilometers - 1300 nM multimode
Twisted
Pair #1
Twisted
Pair #2
Crossover Cable
Connectors for like devices
Twisted
Pair #1
Twisted
Pair #2
Straight Through Cable
Connectors for unlike devices
CABLE SPECIFICATIONS
The physical characteristics of the media cable must meet or exceed IEEE 802.3 specifications.
Fiber Cable
Multimode Cable Recommended: 62.5 / 125 µm multimode fiber
Optional: 100 / 140 µm multimode fiber
85 / 125 µm multimode fiber
50 / 125 µm multimode fiber
Singlemode Cable Recommended: 9/125 µm singlemode fiber
Bit error rate: ≤10
-9
C/E-TBT-FRL-04 850nm multimode
Fiber-optic Transmitter Power: min: -16.0 dBm max: -10.0 dBm
Fiber-optic Receiver Sensitivity: min: -29.5 dBm max: -7.2 dBm
Maximum Cable Distance: 2 kilometers (6,600 feet)
C/E-TBT-FRL-04 (L) 1300nm multimode
Fiber-optic Transmitter Power: min: -19.0 dBm max: -15.0 dBm
Fiber-optic Receiver Sensitivity: min: -34.0 dBm max: -14.0 dBm
Maximum Cable Distance: 5 kilometers (16,500 feet)
C/E-TBT-FRL-04 (MT) 850nm multimode
Fiber-optic Transmitter Power: min: -16.0 dBm max: -10.0 dBm
Fiber-optic Receiver Sensitivity: min: -29.5 dBm max: -7.2 dBm
Maximum Cable Distance: 2 kilometers (6,600 feet)
C/E-TBT-FRL-04 (SC) 850nm multimode
Fiber-optic Transmitter Power: min: -16.0 dBm max: -10.0 dBm
Fiber-optic Receiver Sensitivity: min: -29.5 dBm max: -7.2 dBm
Maximum Cable Distance: 2 kilometers (6,600 feet)
C/E-TBT-FRL-04 (SM) 1300nm singlemode - with ST connectors
Fiber-optic Transmitter Power: min: -23.0 dBm max: -14.0 dBm
Fiber-optic Receiver Sensitivity: min: -34.0 dBm max: -14.0 dBm
Typical Cable Distance*: 20 kilometers (66,000 feet)
C/E-TBT-FRL-04 (LH) 1300nm singlemode - with ST connectors
Fiber-optic Transmitter Power: min: -17.0 dBm max: -12.0 dBm
Fiber-optic Receiver Sensitivity: min: -34.0 dBm max: -14.0 dBm
Typical Cable Distance*: 20 kilometers (66,000 feet)
C/E-TBT-FRL-04 (XC) 1300nm singlemode - with SC connectors
Fiber-optic Transmitter Power: min: -23.0 dBm max: -14.0 dBm
Fiber-optic Receiver Sensitivity: min: -34.0 dBm max: -14.0 dBm
Typical Cable Distance*: 20 kilometers (66,000 feet)
*Actual distance dependent upon physical characteristics of network installation.
Copper Cable and Connector
Twisted pair connection requires two active pairs configured as straight through.
The two active pairs in an Ethernet™ network are pins 1 & 2 and pins 3 & 6. Use
only dedicated wire pairs (such as blue/white & white/blue, orange/white &
white/orange) for the active pairs.
Category 3 or better twisted-pair copper wire is required. Either shielded twisted-
pair (STP) or unshielded twisted-pair (UTP) can be used. DO NOT USE FLAT OR
SILVER SATIN WIRE.
INSTALLATION
Install Slide-In-Module in E-MCC-1600 Chassis
NOTE: Media Converter Slide-in-Modules can be installed in any installation
slot, in any order.
• Remove Media Converter Slide-in-Module protective plate from selected
installation slot by removing two (2) screws that secure plate to front of
E-MCC-1600 chassis.
• Carefully slide Media Converter Slide-in-Module into installation slot,
aligning Media Converter Slide-in-Module with installation guides.
NOTE: Ensure that the Media Converter Slide-in-Module is firmly seated
against the backplane.
• Secure Slide-in-Module by securing panel fastener screw attached to
Slide-in-Module to E-MCC-1600 chassis.
Install Cable
NOTE: See pages 6 and 7 for cable specifications and configurations.
COPPER
EITHER STRAIGHT-THROUGH OR CROSSOVER CABLE CAN BE USED
BETWEEN THE MEDIA CONVERTER AND A HUB, TERMINAL DEVICE,
TRANSCEIVER, SWITCH, OR NETWORK INTERFACE CARD (NIC).
• Locate or build 10BASE-T-compliant cables with either straight-
through or crossover configuration and with male RJ-45 plug
connectors at both ends.
• Connect male RJ-45 plug connector at one end of cable to media
converter RJ-45 jack connector.
• Connect male RJ-45 plug connector at other end of cable to
10BASE-T hub, terminal device, transceiver, switch, or network
interface card (NIC) RJ-45 jack connector.
FIBER
• Locate or build 10BASE-FL-compliant fiber cable with male two-
stranded TX to RX connectors at both ends.
• Connect male TX and RX cable connectors at one end of cable to
TX and RX female connectors, respectively, on media converter.
• Connect male TX and RX cable connectors at other end of cable
to RX and TX connectors of 802.3 compliant fiber device
OPERATION
After installation, the media converter should function without operator
intervention.
Status LEDs
Use the status LEDs to monitor media converter operation in the network.
Link
(near 10BASE-FL connector) Steady LED indicates good
10BASE-FL link and normal operation.
Dark LED
indicates lack of
power OR
downed
10BASE-FL link.
RX (Receive -
near
10BASE-FL connector
) Flashing
LED indicates data reception on
10BASE-FL link.
Link
(near 10BASE-T connector) Steady
LED indicates good 10BASE-T
link and normal operation.
Dark LED indicates lack of power OR downed 10BASE-T
link.
RX (Receive -
near 10BASE-T connector) Flashing LED indicates
data reception on 10BASE-T link.
P(o)w(e)r Steady LED indicates connection to external AC power.
FAULT ISOLATION and CORRECTION
If the media converter fails, isolate and correct the fault by determining the
answers to the following questions and then taking the indicated action:
1. Is the P(ower) LED on the media converter illuminated?
NO
• Is the power adapter the proper voltage and frequency for AC
outlet? NOTE: Refer to “Power Supply Requirements” on page 7.
• Is the power adapter properly installed in the media converter and
in the outlet?
• Contact Technical Support: (800) 260-1312/(800) LAN-WANS.
YES
• Proceed to step 2.
2. Is the 10BASE-T Link LED illuminated?
NO
• Check twisted pair cables for proper connection.
• Contact Technical Support: (800) 260-1312/(800) LAN-WANS.
YES
• Proceed to step 3.
3. Is the 10BASE-FL Link LED illuminated?
NO
• Check fiber cables for proper connection.
• Verify that TX and RX cables on media converter are connected to
RX and TX ports, respectively, on other device.
• Contact Technical Support: (800) 260-1312/(800) LAN-WANS.
YES
• Proceed to step 4.
4. Is the 10BASE-T RX LED illuminated?
NO
• Disconnect and reconnect the 10BASE-T cable to restart the
initialization process.
• Restart the attached device to restart the initialization process.
• Contact Technical Support: (800) 260-1312/(800) LAN-WANS.
YES
• Proceed to step 5.
5. Is the 10BASE-FL RX LED illuminated?
NO
• Disconnect and reconnect the 10BASE-FL cable to restart the
initialization process.
• Restart the attached device to restart the initialization process.
• Contact Technical Support: (800) 260-1312/(800) LAN-WANS.
YES
• Contact Technical Support: (800) 260-1312/(800) LAN-WANS.
10BASE-T
ST Connectors
RX
TX
Link
RX
Link
RX
Pwr
(Fiber)
Link
RX
Pwr
RX
Link
(RJ-45)
RJ-45 Connector
10BASE-T
10BASE-FL
-
1
-
2
-
3
-
4
Transition Networks C/E-TBT-FRL-04(LH) Manuel utilisateur
- Catégorie
- Convertisseurs de média réseau
- Taper
- Manuel utilisateur
- Ce manuel convient également à
dans d''autres langues
Documents connexes
-
Transition Networks J/E-CF-02 Manuel utilisateur
-
Transition Networks Switch CERTXFX01(SM) Manuel utilisateur
-
-
-
-
-
Transition Networks TN-CWDM-SFP-1290 Manuel utilisateur
-
-
