TRG7000
Trigger Handle
Quick Reference Guide
© 2007 MOTOROLA, INC. All rights reserved.
Motorola reserves the right to make changes to any product to improve reliability,
function, or design.
Motorola does not assume any product liability arising out of, or in connection with, the
application or use of any product, circuit, or application described herein.
No license is granted, either expressly or by implication, estoppel, or otherwise under
any patent right or patent, covering or relating to any combination, system, apparatus,
machine, material, method, or process in which Motorola products might be used. An
implied license exists only for equipment, circuits, and subsystems contained in
Motorola products.
MOTOROLA, the Stylized M Logo and Symbol and the Symbol logo are registered
trademarks of Motorola, Inc. Other product names mentioned in this manual may be
trademarks or registered trademarks of their respective companies and are hereby
acknowledged.
Warranty
For the complete Motorola hardware product warranty statement, go to:
http://www.symbol.com/warranty
.
Patents
This product is covered by one or more patents. For patent information go to: http://
www.symbol.com/patents.
Motorola, Inc.
One Motorola Plaza
Holtsville, New York 11742, USA
1-800-927-9626
http://www.symbol.com
MOTOROLA and the Stylized M Logo and Symbol and the Symbol logo are
registered in the U.S. Patent and Trademark Office. All other product or service
names are the property of their respective owners.
© Motorola, Inc. 2007
72-73348-02 Revision A — September 2007
1 2 3
Introduction
The TRG7000 Trigger Handle (P/N: 21-70982-01) adds a gun-style
handle with a scanning trigger to the MC70 Enterprise Digital
Assistants (EDAs). It increases comfort when using the EDA in
scan-intensive applications for extended periods of time.
The TRG7000 is intended for use with MC70 WLAN/PAN
configurations.
For detailed information on the MC70 EDA, refer to the MC70 User
Guide.
Installing the Trigger Handle Cleat
The Trigger Handle comes with a trigger handle cleat that replaces
the back housing bracket on the MC70.
1. Remove the handstrap by threading the handstrap through the
handstrap slot.
2. Remove the four screws securing the back housing bracket to the
MC70. Save these screws. You will use them later to secure the
trigger handle cleat.
3. Remove the back housing bracket.
4. Install the rubber headset jack dust cover onto the trigger handle
cleat.
5. Align the trigger handle cleat onto the MC70.
6. Secure the trigger handle cleat to the MC70 using the four screws
saved during step 2.
7. Feed the handstrap through the handstrap slot and secure.
Inserting the MC70 into the Trigger Handle
Slide the MC70 into the Trigger Handle until it locks in place. The
release secures the MC70 to the Trigger Handle.
Removing the MC70
To remove the MC70, press the release down and pull the MC70
forward.
Scanning
To scan bar codes:
1. Start the MC70’s scanning application.
2. Aim the MC70 at the bar code.
3. Pull the trigger on the handle.
The Scan/Decode LED lights
and a beep sounds to indicate
a successful decode.
For more information on MC70
scanner functions, refer to the
MC70 User Guide.
Charging and Communication
The Trigger Handle can be used to charge the MC70 and
communicate with a host computer using either the Serial Charging
Cable or a cradle, or connect to a peripheral such as a printer.
Using the Serial Charging/Communication Cable
To charge the MC70’s battery or communicate with a host computer
while the MC70 is in the Trigger Handle, use the Serial Charging
Cable setup below:
Using a Cradle
To charge the MC70’s battery while the MC70 is in the Trigger
Handle, use either the Single-Slot Serial/USB cradle or the Four-Slot
Ethernet cradle.
CAUTION The trigger handle cleat secures the MC70 into the
Trigger Handle and prevents the MC70 from slipping
out of the Trigger Handle. Failure to install the cleat
may result in damage to the MC70.
Alternate
Stylus Holder
Optional
Handstrap
Trigger
Release
Back
Housing
Bracket
Release
Release
CAUTION Do not place a Trigger Handle with an attachment,
such as a Magnetic Stripe Reader (MSR) into a cradle.
Remove the attachment before inserting the Trigger
Handle into the cradle.
Power Supply
AC Line Cord
Charging/Communication Cable
5 6 74
Troubleshooting
Refer to the MC70 User Guide for MC70 specific troubleshooting
procedures.
Ergonomic Recommendations
•
Reduce or eliminate repetitive motion
•
Maintain a natural position
•
Reduce or eliminate excessive force
•
Keep objects that are used frequently within easy reach
•
Perform tasks at correct heights
•
Reduce or eliminate vibration
•
Reduce or eliminate direct pressure
•
Provide adjustable workstations
•
Provide adequate clearance
•
Provide a suitable working environment
•
Improve work procedures.
Regulatory Information
This device is approved under the Symbol Technologies brand;
Symbol Technologies, Inc., is the Enterprise Mobility business of
Motorola, Inc. (“Motorola”).
All Symbol devices are designed to be compliant with rules and
regulations in locations they are sold and will be labeled as required.
Any changes or modifications to Symbol Technologies equipment,
not expressly approved by Symbol Technologies, could void the
user's authority to operate the equipment.
Local langauge translations are available at the following website:
http://support.symbol.com.
Power Supply
Use only a Symbol approved and correctly rated power supply as
appropriate for the country of operation. Use of alternative power
supplies will invalidate any approval given to the device and may be
dangerous.
Refer to the MC70 User Guide for detailed power supply
information. The latest product documentation (User Guide) is
available at http://support.symbol.com.
Battery Charging
To charge the battery for the mobile device, battery and charger
temperatures must be between +32° F and +104° F (0° C and +40°
C).
Radio Frequency Interference Requirements - FCC
NOTE This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC rules. These limits
are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna
•
Increase the separation between the equipment and receiver
•
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected
•
Consult the dealer or an experienced radio/TV technician for
help.
Radio Frequency Interference Requirements - Canada
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme
NMB-003 du Canada.
Marking and European Economic Area (EEA)
Symbol Technologies, Inc., hereby declares that this device is in
compliance with all the applicable Directives, 89/336/EEC, 73/23/
EEC. A Declaration of Conformity may be obtained from http://
www2.symbol.com/doc/
Waste Electrical and Electronic Equipment
(WEEE)
English: For EU Customers: All products at the end of their life must be
returned to Motorola for recycling. For information on how to return product,
please go to: http://www.symbol.com/environmental_compliance.
Bulgarish: За клиенти от ЕС: След края на полезния им живот всички
продукти трябва да се връщат на Motorola за рециклиране. За
информация относно връщането на продукти, моля отидете на адрес:
http://www.symbol.com/weeelink.
Dansk: Til kunder i EU: Alle produkter skal returneres til Motorola til
recirkulering, når de er udtjent. Læs oplysningerne om returnering af
produkter på: http://www.symbol.com/environmental_compliance.
Deutsch: Für Kunden innerhalb der EU: Alle Produkte müssen am Ende
ihrer Lebensdauer zum Recycling an Motorola zurückgesandt werden.
Informationen zur Rücksendung von Produkten finden Sie unter http://
www.symbol.com/environmental_compliance.
Eesti: EL klientidele: kõik tooted tuleb nende eluea lõppedes tagastada
taaskasutamise eesmärgil Motorola'ile. Lisainformatsiooni saamiseks toote
tagastamise kohta külastage palun aadressi: http://www.symbol.com/
environmental_compliance.
Español: Para clientes en la Unión Europea: todos los productos deberán
entregarse a Motorola al final de su ciclo de vida para que sean reciclados.
Si desea más información sobre cómo devolver un producto, visite: http://
www.symbol.com/environmental_compliance.
Français : Clients de l'Union Européenne : Tous les produits en fin de cycle
de vie doivent être retournés à Motorola pour recyclage. Pour de plus
amples informations sur le retour de produits, consultez : http://
www.symbol.com/environmental_compliance.
Italiano: per i clienti dell'UE: tutti i prodotti che sono giunti al termine del
rispettivo ciclo di vita devono essere restituiti a Motorola al fine di
consentirne il riciclaggio. Per informazioni sulle modalità di restituzione,
visitare il seguente sito Web: http://www.symbol.com/
environmental_compliance.
Magyar: Az EU-ban vásárlóknak: Minden tönkrement terméket a Motorola
vállalathoz kell eljuttatni újrahasznosítás céljából. A termék
visszajuttatásának módjával kapcsolatos tudnivalókért látogasson el a http://
www.symbol.com/environmental_compliance weboldalra.
Nederlands: Voor klanten in de EU: alle producten dienen aan het einde van
hun levensduur naar Motorola te worden teruggezonden voor recycling.
Raadpleeg http://www.symbol.com/environmental_compliance voor meer
informatie over het terugzenden van producten.
Português: Para clientes da UE: todos os produtos no fim de vida devem
ser devolvidos à Motorola para reciclagem. Para obter informações sobre
como devolver o produto, visite: http://www.symbol.com/
environmental_compliance.
Românesc: Pentru clienţii din UE: Toate produsele, la sfârşitul duratei lor de
funcţionare, trebuie returnate la Motorola pentru reciclare. Pentru informaţii
despre returnarea produsului, accesaţi: http://www.symbol.com/weeelink.
Slovenski: Za kupce v EU: vsi izdelki se morajo po poteku življenjske dobe
vrniti podjetju Motorola za reciklažo. Za informacije o vraèilu izdelka obišèite:
http://www.symbol.com/environmental_compliance.
Suomi: Asiakkaat Euroopan unionin alueella: Kaikki tuotteet on palautettava
kierrätettäväksi Motorola-yhtiöön, kun tuotetta ei enää käytetä. Lisätietoja
tuotteen palauttamisesta on osoitteessa http://www.symbol.com/
environmental_compliance.
Svenska: För kunder inom EU: Alla produkter som uppnått sin livslängd måste
returneras till Motorola för återvinning. Information om hur du returnerar
produkten finns på http://www.symbol.com/environmental_compliance.
Service Information
If you have a problem using the equipment, contact your facility’s
Technical or Systems Support. If there is a problem with the
equipment, they will contact the Motorola Enterprise Mobility
Support at: http://www.symbol.com/contactsupport.
For the latest version of this guide go to:
http://www.symbol.com/support
.
Problem Cause Solution
Scan line does
not appear when
trigger is
pressed.
MC70 is not attached
properly to the Trigger
Handle and is not making
contact with the
connector.
Remove the MC70 from
the Trigger Handle and
reinsert.
MC70 does not contain a
scanning application.
Load a scanning
application on the MC70.
Refer to the MC70
Integrator Guide.
Scanning application is
not active.
Start the scanning
application.
MC70 battery
does not charge
when Trigger
Handle is placed
in a cradle.
Trigger Handle is not
properly seated in the
cradle.
Remove the Trigger
Handle from the cradle
and reinsert.
Power is not available to
the cradle.
Ensure that power
connections to the cradle
are connected properly.
Cannot print to
printer.
Printer cable not
connected properly.
Ensure cable is
connected properly to the
printer and Trigger
Handle.
MC70 does not
wake from
suspend mode
when trigger is
pressed.
The trigger only wakes
the MC70 from the
suspend mode if a
scanning application is
active.
Press a key on the MC70
to wake from the
suspend mode.
CAUTION In order to avoid or minimize the potential risk of
ergonomic injury follow the recommendations below.
Consult with your local Health & Safety Manager to
ensure that you are adhering to your company's safety
programs to prevent employee injury.
CAUTION Only use Symbol approved and UL Listed mobile
computers, accessories, battery packs and battery
chargers. Do NOT attempt to charge damp/wet mobile
computers or batteries. All components must be dry
before connecting to an external power source.
-
1
-
2
