Vermeiren Mercurius 4D Manuel utilisateur

VERMEIREN

Mercurius 4D

I N S

T R U C T I O N M A N U A L

M A N U E L D ' U T I L I S A T I O N

G E B R U I K S A A N W I J Z I N G

G E B R A U C H S A N W E I S U N G

M A N U A L E D I I S T R U Z I O N I

M A N U A L D E I N S T R U C C I O N E S

I N S T R U K C J A O B S Ł U G I

N Á V O D K O B S L U Z E

Instrukcje dla wyspecjalizowanego

sprzedawcy

All

rights reserved, including translation.

No part of this manual may be reproduced in any form what so

ever (print, photocopy, microfilm or any other process) without

written permission of the publisher, or processed, duplicated or

distributed by using electronic systems.

Aucune partie de ce manuel ne peut être reproduite, sous

quelque forme que ce soit (imprimée, photocopie, microfilm ou

tout autre procédé) sans l'autorisation écrite du publicateur, ni

traitée, dupliquée ou distribuée à l'aide de systèmes

électroniques.

Alle rechten, inclusief vertaling, voorbehouden.

Niets uit deze handleiding mag geheel of gedeeltelijk in enige

vorm (druk, fotokopie, microfilm of ieder ander procedé) zonder

de schriftelijke toelating van de uitgever worden

gereproduceerd of met behulp van elektronische systemen

worden verwerkt, gekopieerd of verspreid.

Alle Rechte, auch an der Übersetzung, vorbehalten.

Kein Teil der Gebrauchsanweisung darf in irgendeiner Form

(Druck, Fotokopie, Mikrofilm oder einem anderen Verfahren)

ohne schriftliche Genehmigung des Herausgebers

reproduziert oder unter Verwendung elektronischer Systeme

verarbeitet, vervielfältigt oder verbreitet werden.

Il presente manuale non può essere riprodotto, neppure

parzialmente, con alcun mezzo (stampa, fotocopia, microfilm o

altro procedimento) senza l’autorizzazione scritta della casa

produttrice, né elaborato, duplicato o distribuito con l’ausilio di

sistemi elettronici.

traducción.

Se prohíbe la reproducción total o parcial del presente manual

de cualquier forma (impresión, fotocopia, microfilm o cualquier

otro procedimiento), así como la edición, copia o distribución

empleando sistemas electrónicos, sin el permiso escrito del

editor.

Wszelkie prawa zastrzeżone, łącznie z tłumaczeniem.

Żadna część niniejszej instrukcji nie może być powielana w

jakiejkolwiek formie (drukowanej, fotokopii, mikrofilmu ani

innej) bez pisemnej zgody wydawcy, nie może być również

przetwarzana, kopiowana ani rozprowadzana za pomocą

systemów elektronicznych.

Všechna práva vyhrazena, včetně překladu.

Šíření jakékoliv části tohoto katalogu jakýmkoliv způsobem

(tisk, kopie, mikrofilm nebo jiný způsob) bez písemného

souhlasu vydavatele, nebo zpracování, duplikace či distribuce

prostřednictvím elektronických systémů je zakázáno.

EN

Instructions for specialist dealer

This instruction manual is part and parcel of the

product and must accompany every product

sold.

Version: D, 2021-02

FR

Instructions pour les distributeurs

Ce manuel d'instructions fait partie du produit et

doit accompagner chaque produit vendu.

Version : D, 2021-02

NL

Instructies voor de vakhandelaar

Deze handleiding is deel van het product en

dient bij iedere product te worden geleverd.

Versie: D, 2021-02

DE

Hinweise für den Fachhändler

Diese Gebrauchsanweisung ist Bestand-teil des

Produkts und ist bei jeder Produkts

auszuhändigen.

Version: D, 2021-02

IT

Istruzioni per il rivenditore

Il presente Manuale di istruzioni è parte

integrante del prodotto e deve essere fornito

assieme alla prodotto.

Versione: D, 2021-02

ES

Instrucciones destinadas a los distribuidores

especializados

El presente manual de instrucciones es parte

integrante del producto y se debe adjuntar a

todas las producto que se vendan.

Versión: D, 2021-02

PL

Niniejsza instrukcja obsługi jest nieodłączną

częścią produktu i musi być dołączona do

każdego sprzedawanego produktu.

Wersja: D, 2021-02

CS

Pokyny pro specializovaného prodejce

Tento návod k obsluze je součástí dodávky a

musí být součástí každého prodaného

produktu.

Verze: D, 2021-02

Basic UDI: 5415174 122124Mercur4D DU

Multi version: D, 2021-02

Language index

English

Français

Nederlands

Deutch

Italiano

Español

Polski

Czech

User manual

Manuel d'utilisation

Gebruiksaanwijzing

Bedienungshandbuch

Manuale di istruzioni

Manual de instrucciones

Instrukcja obsługi

Návod k obsluze

This page is intentionally left blank

Mercurius 4D

2021-02

Contents

1

EN

NL

Contents

Contents ..................................................................................................................... 1

Preface........................................................................................................................ 2

1 Your product .................................................................................................. 3

1.1 Description .................................................................................................... 3

1.2 Accessories ................................................................................................... 3

2 Before use ..................................................................................................... 4

2.1 Intended use ................................................................................................. 4

2.2 General safety instructions ............................................................................ 4

2.3 Symbols on the scooter ................................................................................. 5

2.4 Transport ....................................................................................................... 5

2.5 First use and storage .................................................................................... 6

3 Using your scooter ....................................................................................... 7

3.1 First ride ........................................................................................................ 7

3.2 Operating your scooter .................................................................................. 7

3.3 Transfer in and out of the scooter ............................................................... 11

3.4 Brake and free-wheel lever ......................................................................... 11

3.5 Comfort adjustments ................................................................................... 12

3.6 Automatic power shutdown ......................................................................... 14

3.7 Charging the batteries ................................................................................. 14

3.8 Thermal fuses ............................................................................................. 16

3.9 Anti-tipping .................................................................................................. 16

4 Maintenance ................................................................................................ 17

4.1 Cleaning ...................................................................................................... 17

4.2 Expected lifespan ........................................................................................ 17

4.3 Reuse .......................................................................................................... 17

4.4 End of use ................................................................................................... 18

4.5 Warranty ...................................................................................................... 18

5 Troubleshooting .......................................................................................... 19

6 Technical specifications ............................................................................. 20

Mercurius 4D

2021-02

Preface

2

EN

NL

Preface

Congratulations! You are now owner of a Vermeiren scooter!

This scooter is made by qualified and committed personnel. It is designed and produced

according to high quality standards guarded by Vermeiren.

Thanks for your trust in the products of Vermeiren. To support you on the use of this scooter and

its operating options, this manual is offered. Please read it carefully; it will help you to get familiar

with the operation, capabilities and limitations of your scooter.

If you still have questions after reading this manual, do not hesitate to contact your specialist

dealer. He/she will be glad to help you on this subject.

Important note

To ensure your safety and to prolong the lifetime of your product, please take good care of it and

have it checked and/serviced on regular base.

This manual reflects the latest product developments. Vermeiren has the right to implement

changes to this type of product without being imposed to any obligation to adapt or replace similar

products previously delivered.

Pictures of the product are used to clarify the instructions in this manual. Details of the depicted

product may deviate from your product.

Information available

On our website http://www.vermeiren.com/ you will always find the most recent version of the

information in this manual. Please consult this website regularly for possible updates.

Visually impaired people can download the electronic version of this manual and have it read out

by means of a text-to-speech software application.

This user manual

For user and specialist dealer

User manual of battery charger.

For user and specialist dealer

Service manual for scooters

For specialist dealer

EC declaration of conformity

Mercurius 4D

2021-02

Your product

3

EN

NL

1 Your product

1.1 Description

1.2 Accessories

The following accessories are available for the scooters Mercurius 4D:

 Rear view mirrors

 Manual brakes

 Crutch holder

1.

Headrest

2. Backrest

3. Armrest / Armpad

4. Seat

5. Rear wheel

6. Footplate

7. Front wheel

8. Front light

9. Indicator lights

10. Rearview mirror

11. Speed lever

12. Handgrips

13. Basket

14. Freewheel lever

15. Rear lights

16. Antitipping

17.

Identification plate

1

2

3

4

5

6

7

8

9

10

11

12

14

13

9

15

16

17

Mercurius 4D

2021-02

Before use

4

EN

NL

2 Before use

2.1 Intended use

In this paragraph a brief description of the intended use of your scooter is given. Additionally,

relevant warnings are added to the instructions in the other paragraphs. In this way we would like

to make you aware of the possible misuse that may appear.

 This scooter is classified as a class C product and is suitable for outdoor use.

 This scooter is designed and produced solely to transport one (1) person with a maximum

weight of 150kg. It is not designed to transport goods or objects, or for any other use than

the transport previously described.

 You should NOT use this scooter if you suffer from physical or mental impairments that may

put you, or other people, in danger when driving the scooter, such as; visual impairment,

mental disorder, hemiplegics or paraplegics. For this reason, consult your doctor first and

make sure that your specialist dealer is informed about his advice.

 If applicable, only use accessories and spare parts approved by Vermeiren.

 Please read all technical details and limits of your scooter in chapter 6.

 The warranty on this product is based on normal use and maintenance as described in this

manual. Damage to your product caused by improper use or lack of maintenance will cause

the warranty to lapse.

2.2 General safety instructions

Risk of injuries and/or damage

Please read and follow the instructions in this manual. Otherwise you may get injured or your

scooter may get damaged.

Keep the following general warnings in mind during use:

 Do not use your scooter if you are under the influence of alcohol, medicines or other

substances that may influence your driving abilities.

 Be aware that some parts of your scooter may get very hot or cold due to ambient

temperature, solar radiation, heating devices or due to the motor drive during the ride. Be

careful when touching. Wear protective clothing if the weather is cold. After a ride, wait until

the scooter/motor has cooled down.

 Before switching the scooter on, be aware of the environment/situation in which you are

located. Adjust your speed to this before driving off. We advise you to use the slowest speed

setting to drive indoors. For outdoor driving you can adjust the speed to a suitable speed at

which you feel comfortable and safe.

 ALWAYS keep in mind that your scooter may stop suddenly due to a discharged battery or a

protection that prevents your scooter from further damage. Also check the causes mentioned

in chapter 6.

 Your scooter has been tested for electromagnetic compatibility and complies with the

standard. Nevertheless, sources of electromagnetic fields, such as the fields of mobile

phones, power generators or high-power energy sources, may influence the driving

performance of your scooter. On the other hand, the electronics of your scooter may affect

other electronic appliances as well, such as alarm systems of shops and automatic doors.

We therefore advise you to check your scooter regularly for damage and wear, since these

may enlarge the interference (see also chapter 4).

 Only drive on flat surfaces where all four wheels touch the ground and where there is sufficient

contact to operate the scooter safely.

 Make sure that your hands, clothes, belts, buckles or jewellery don’t get caught by wheels or

other moving parts during use.

CAUTION

Mercurius 4D

2021-02

Before use

5

EN

NL

2.3 Symbols on the scooter

The symbols in following list are applicable for your scooter. Missing symbols can be found in the

relevant ISO standard (ISO 7000, ISO 7001 and IEC 417).

Maximum weight of the user

Outdoor use

Indoor use (battery charger only)

Maximum safe slope in °.

Maximum speed

Type designation

Risk of entrapment

2.4 Transport

2.4.1 Moving the scooter

The best way to carry the scooter is to make use of the neutral mode. Place the scooter in neutral

and roll the scooter to the desired place.

If this is not possible, you can carry the scooter according to the following steps:

1. Switch the scooter off.

2. Remove loose parts (seat and batteries).

3. Store loose parts in a safe place.

4. Carry the frame + steering unit with 2 or 3 persons to the desired place. Hold the frame to

the chassis or fixed parts of the frame, not the bumpers or the plastic parts.

2.4.2 Transport in the car

Risk of injury - The scooter is not suited for use as a seat in a motor

vehicle.

Risk of injury

 Remove all loose parts prior to transportation.

 No people or objects should be under the scooter, on the footplate or seat during transportation.

 Make sure that the scooter is attached properly to avoid injury of the passengers during

collision or sudden braking.

 Do not place fingers between the components of the scooter.

The best way to transport your scooter in the car is to drive the scooter in the car using ramps.

When you are not experienced to drive the scooter using ramps, you can also put the scooter in

neutral mode and push the scooter in the car using ramps.

DANGER

WARNING

Mercurius 4D

2021-02

Before use

6

EN

NL

When the scooter does not fit in the car, it is also possible to transport the scooter according to

the following steps:

1. Remove all loose parts prior to transport (seat, etc.).

2. Store loose parts safely.

3. If possible, remove the batteries / battery boxes to save weight.

4. Fold the steering unit down with the angle adjustment.

5. Place the scooter in the car with 2 or 3 persons.

6. Attach the frame of the scooter securely to the vehicle.

2.5 First use and storage

Risk of battery damage

 Never completely discharge the battery.



Do not interrupt the charging cycle; only disconnect the battery charger when the battery is

fully charged.

 Make sure that your scooter is stored dry and indoors to prevent mould from growing

and the

upholstery from being damaged. If necessary, use a protective cover.



Check the technical details for storage, see chapter

6

.

Ensure that the battery has been fully charged before using your scooter, ask your dealer if this

has already been done or not. To charge, follow the charging instructions in §3.7.

CAUTION

Mercurius 4D

2021-02

Using your scooter

7

EN

NL

3 Using your scooter

Risk of injuries

 First read previous chapters and inform yourself about the intended use. Do NOT use your

scooter unless you have read and fully understood all instructions.

 In case of doubts or questions, do not hesitate to contact your local specialist dealer, your care

provider or technical adviser to help you with this.

3.1 First ride

Risk of injuries and damage

 Make sure that your scooter is switched OFF when getting on and off.



Always unplug the battery charger from the scooter before starting to drive.

Make sure you are familiar with the operation of your scooter before using it on crowded and

possibly dangerous places. First exercise at a specious, open area with little bystanders and

ask someone to accompany you.

1. Make sure that:

 the scooter is on a flat surface with all wheels touching the ground;

 the battery is fully charged , see § 3.7;

 the motor is coupled, see § 3.4;

 the tyres have the correct tyre pressure, see § 6;

 you have the correct sitting position;

 all adjustments have been fixed securely.

2. Switch your scooter on, see § 3.2.

3. Set the speed to lowest speed setting, see § 3.2.

4. Put both hands on the handgrips of the tiller.

5. Slightly pull the right operating lever to drive to the front. Use the left operating lever to drive

backwards. Release the lever to stop. Repeat this a few times.

6. If you feel confident enough, repeat this at a higher speed.

7. Now try to turn, in forward and backward direction. Repeat this a few times.

8. Make sure your scooter stands stable when ending the ride.

9. Switch off the scooter and remove the key to protect against theft.

3.2 Operating your scooter

Risk of injuries or damage

 Do NOT drive on slopes, obstacles, steps or kerbs larger than the size described in the

technical specifications in chapter 6.

 Take the local road traffic law into consideration; it may differ per country.

 Do not adjust the speed while you are driving.

 Take the weather conditions into consideration. Avoid driving by moist weather, extreme heat,

snow, black ice, freezing temperatures; see technical specifications in chapter 6.

 To prevent tipping over, try to drive with a large turning radius at corners and curves. Do not

cut corners and don’t drive with sharp bends. Try to drive straight in small passages to prevent

getting entrapped.

 Do not lean too far to the left/right/front/back of the scooter to prevent tipping over. Please

pay specially attention when you are negotiating slopes and obstacles.

 Be aware of other road users to whom your scooter may be an obstacle. Pay special attention

when turning, reversing or driving backward. If you are not acquainted with driving backwards,

first practice in an open area. Indicate the direction you intent to go before cornering.

CAUTION

WARNING

Mercurius 4D

2021-02

Using your scooter

8

EN

NL

 When driving indoors, only use the lowest speed setting.

 Do not turn your scooter "OFF" while driving as this will lead to an emergency stop and

possible risk of accident and injury.

 Keep the braking distance in mind, see also the technical specification in chapter 6. Be aware

that the braking distance depends on speed, surface, weather conditions, slope and weight

of the user.

 Pay attention if the road has holes or gaps that may cause entrapment of the wheels.

3.2.1 Operator control

 Switch the scooter ON by turning the key.

 The battery level indicator (1) will light up and show the current level of your batteries.

 Press the speed control (2, 3, 4) to select the desired driving speed.

o Press button (4) to choose between the high/low speed setting.

o Press button (2) to lower the speed within the chosen setting.

o Press button (3) to raise the speed control.

 To sound the horn, press the horn button (5).

 To switch on the front and back lights, press the light button (7).

 To switch on the emergency flashers, press button (10).

 To switch on the indicator lights, press the desired button (9) (right indicator) or (8) (left

indicator). The buzzer will make a beeping sound when turning the indicators lights on.

3.2.2 LCD display

The time setting is linked to the battery system.Once you change to or connect new batteries, you

must reset the time setting.

The system has a mileage memory for driving distance. You do not have to reset the mileage

display after changing the batteries.

1. Battery level indicator / LCD display

2. Speed control (slow)

3. Speed control (fast)

4. Speed switch

5. Horn

6. Set: change mode

7. Lights (front and rear)

8. Indicator (left)

9. Indicator (right)

10. Emergency lights

1. Temperature display

2. Speed bar

3. Speed display

4. Time display

5. Mileage or distance display

6. Battery indicator

7. High / slow speed mode

display

8. Controller fault code

1

2

3

4

5

6

7

8

9

1

0

1

2

3

4

5

6

7

8

Mercurius 4D

2021-02

Using your scooter

9

EN

NL

3.2.3 Setting

Press to change mode, to modify time and display.

Normal AM/PM hour minute Temp °C/°F

(speed) kmh/mph, (distance) km/mile Normal

Vermeiren is responsible for the changes in the software.Contact your dealer or Vermeiren for

questions or updates.

3.2.4 Operating the brakes

To apply the electromagnetic brakes:

1. Let go of the speed lever. The electromagnetic brake in the motor will be activated, the

scooter will stop.

To apply the manual brakes (optional) - emergency brake:

1. Pull the brake lever (1) towards the handgrip.

2. Release the brake lever.

To apply the manual brakes (optional) - parking brake:

1. Pull the brake lever (1) towards the handgrip and use

the button to lock it.

2. Squeeze the brake lever again to release the button.

The manual brake tightness can be adjusted with the brake

cable adjuster.

3.2.5 Driving the scooter

Risk of injuries

 Do not use both sides of the speed lever simultaneously. This might leave you unable to control

your scooter.

Move the speed lever in the required direction:

PULL ACTION BY THE RIGHT HAND = FORWARD MOVEMENT

PULL ACTION BY THE LEFT HAND = BACKWARD MOVEMENT

Pulling the lever more will increase the speed within the selected speed setting. Only use higher

speed settings when you are confident that you can easily operate and control your scooter.

When you switch on the scooter, wait for 3 seconds before pulling the speed lever. Otherwise,

the horn will sound as a warning and the scooter will not move. If this is the case, switch OFF the

scooter and switch ON again.

3.2.6 Braking

To brake, let go of the speed lever. It will return to the neutral position and slow down your scooter

to a gentle stop. Practice pulling away and braking to get accustomed to the scooter. You need

to be able to estimate how your scooter will react when you drive or brake.

SET (3 sec)

SET

WARNING

Mercurius 4D

2021-02

Using your scooter

10

EN

NL

3.2.7 Driving around corners and in bends

Risk of tipping injuries

 Reduce your speed before you enter a curve or corner.

 Always maintain an adequate distance from corners and obstacles.

 Do not drive your vehicle in an "S" pattern or make erratic turnings.

For corners and bends, use both hands to turn the handle bar in the direction you wish to take.

It is very important that you ensure that there is enough space allowing you to go around bends

and corners. Narrow passages must preferably be approached in a large curve so as to allow you

to enter the narrowest part as straight from the front as possible. Bear in mind that your scooter’s

back part will in most cases be wider than the front part.

3.2.8 Backward movement

The speed of rearward movement is automatically reduced in comparison with forward driving.

We also recommend that you use the slowest speed setting when you drive backward.

Do not forget that the steering direction with rearward driving is the opposite of when you go

forward, and that your scooter will turn directly in the required direction.

The horn will beep while driving the scooter backwards.

3.2.9 Taking slopes

Risk of injuries and/or damage

 Never put your scooter in free-wheel mode on a slope. The scooter may start moving, causing

injuries to you or bystanders.

 Do not turn when driving down a slope, since the weight of the scooter may cause tipping over.

 Make sure all four wheel touch the ground while driving up or down.

Driving up

 Drive in a straight line and with higher speed on a slope, and lean slightly forward. When

you drive in an angle or too slow, there is a risk of tipping over or falling.

 Never reverse on a slope.

Going downhill

 Drive in a straight line (forward or backward) and with lower speed on a slope. When you

drive in an angle or too fast, there is a risk of tipping over or falling.

 Lean slightly backward during a forward descent; lean slightly forward during a backward

descent.

3.2.10 Coping with obstacles

Risk of injuries by unexpected movement

 Do not use your scooter on an escalator.

 Always approach a kerb from the front.

 Make sure that all wheels make contact to the ground when driving up or down.

It is possible to drive with your scooter over steps of 100 mm maximum. Take a 500 mm run-up

to take these step.

WARNING

Mercurius 4D

2021-02

Using your scooter

11

EN

NL

3.3 Transfer in and out of the scooter

1. Park the scooter as close as possible to the place where you want to

transfer.

2. Make sure that the scooter is switched off.

3. Turn the armpad upwards on the side where you want to transfer.

4. Transfer to / from the seat of the scooter.

3.3.1 Correct position in the scooter

Some recommendations to comfortably use the scooter:

1. Position your lower back as close as possible to the backrest.

2. Make sure your upper legs are horizontal.

3.4 Brake and free-wheel lever

Risk of injuries and/or damage

 Only operate the free-wheel lever when your scooter is turned OFF!

 An attendant should operate the free-wheel lever if you have impaired mobility. NEVER operate

it from sitting position.

The scooter is fitted with a free-wheel device that is accessible and operable by the attendant, or

the user when he/she is not sitting in the scooter. You should only put the scooter in neutral to

transport the scooter or to move it out of a danger zone.

 Drive

1. While the scooter is OFF, switch the freewheel lever to “drive.

2. Switch the scooter ON.

3. Electronically controlled driving is now possible.

 Neutral

1. Switch the scooter OFF.

2. Switch the freewheel lever to “neutral”.

3. The scooter can now be pushed without electronic drive.

100 mm

500 mm

WARNING

Mercurius 4D

2021-02

Using your scooter

12

EN

NL

3.5 Comfort adjustments

Risk of injuries and/or damage

 Never perform adjustments while driving.

 The allowed adjustments can change the stability of your scooter (tilting back or sideways).

3.5.1 Adjusting the steering unit

Risk of injury

 Turn the scooter off before you adjust the angle of the steering unit.

 Do not lean with your whole body on the steering unit.

The steering unit can be adjusted to many different positions

(stepless) to suit each driver.

1. Push the lever downwards.

2. Adjust the steering unit to the desired position.

3. Release the lever.

3.5.2 Adjusting the seat

Risk of injury

 Make sure that the seat is locked securely.

Removing the seat

1. Pull the seat lever upwards.

2. Turn the seat a little bit and lift the seat out the adjustment bar.

3. Release the seat lever.

WARNING

Mercurius 4D

2021-02

Using your scooter

13

EN

NL

Placing and locking the seat into place

1. Pull the seat lever upwards.

2. Place the seat on the adjustment bar and, at the same time, keep the seat lever pressed in.

3. Release the seat lever.

4. Make sure that the seat is firmly secured.

Swivelling the seat

1. Pull the seat lever upwards.

2. Turn the seat in the desired direction.

3. Release the seat lever. The seat will always stop after 90°.

4. Make sure that the seat is firmly secured.

Depth adjustment

1. Pull the seat depth adjustment lever upwards.

2. Move the seat forward or backward over the seat depth rails.

3. To lock the seat in place, let go of the lever once the seat has

reached the desired position.

4. Swivel the seat a little until it locks in position.

5. Make sure that the seat is locked securely.

3.5.3 Adjusting the backrest

A tilt lever (2) has been added to the side of the

backrest (transition to seat upholstery). Pull this lever

upwards to release the backrest and fold the

backrest forward (-75°), or adjust the angle of the

backrest (0°-22°).

3.5.4 Adjusting the headrest:

1. Gently press the locking pin (1) toward the headrest.

2. Move the headrest to the desired height.

3. Let go of the locking pin (1).

4. The headrest audibly locks into place.

1

2

1 = Seat system

2 = Tilt lever

1

1 = Locking pin

Mercurius 4D

2021-02

Using your scooter

14

EN

NL

3.5.5 Adjusting the armrests

Risk of tipping over

 Make sure that the armrests are positioned symmetrically from the seat.

 Always mount the inner tube on a safe distance of 50 mm in the outer tube.

The armrest can be adjusted in height and depth.

Adjusting armrest height

Risk of injury - Do not put your fingers, buckles, clothes, jewelry between

the swing away system of the armpad.

1. Fold the armpad backwards.

2. Loosen the star knob.

3. Grasp the armpad.

4. Move the armpad upwards or downwards until the desired

height (range: 30 mm stepless).

5. Retighten the star knob.

6. Make sure that the armrest is well secured.

Adjusting armrest width

1. Loosen the star knob on the back of the scooter.

2. Grasp the inner square tube.

3. Move the tube to adjust the armrest to the desired depth

(range: 120 mm each side stepless).

4. Retighten the star knob.

5. Make sure that the armrest is well secured.

3.6 Automatic power shutdown

In order to avoid accidental battery rundown, your scooter is equipped with an automatic power

shutdown facility. If the scooter is switched on and remains undisturbed for a period of ten

minutes, it will automatically turn off. Should this occur, simply switch your scooter off and back

on and it will be ready to use again.

3.7 Charging the batteries

Risk of injuries and damage due to fire

 Only use the battery charger delivered with the scooter

. The use of any other charger may be

dangerous (fire hazard).

 The battery charger is only intended to charge the batteries delivered with the scooter

, not to

charge any other batteries.



Do not adapt any of the delivered parts, like cables, plugs or battery charger. Never open or

change the battery or the connection points.



Protect the battery and battery charger against flames, high and low temperatures (see chapter

6), moisture, sunshine, severe shocks (for example dropping). Do

NOT use the battery if this

has been the case.

 Charge the battery with the battery charger, indoors, in a well-

ventilated area, out of children's

reach.

 First read the user instruction of the applied battery charger before charging the

scooter’s

battery

. For more information, contact your specialist dealer or consult our website

http://www.vermeiren.com/

WARNING

CAUTION

Mercurius 4D

2021-02

Using your scooter

15

EN

NL

Risk of damage

 Battery self-discharge and the quiescent current of the connected users will drain the

battery

charge slowly. The battery may be irreversibly damaged if the battery is fully discharged.

Therefore, make sure that the battery is charged on time:

o With intensive use (long distances, daily use): Immediately recharge after use.

o With

average use (short distances, daily or a few times a week): Charge when battery

indicator shows 50% discharge.

o With little use or storage: Charge once a week.

 Read the storage and maintenance instructions in chapter 4 and technical

details in chapter 6.

 Only disconnect the battery charger when the battery is fully charged, see

the following symbols on the charger.

 Do not charge batteries below 0°C. Move the battery to a warmer place

and start charging.

 Keep the connection point for the battery charger free of dust and other contamination.



In case of any problems whereby the battery cannot be charged according to following

instructions, please contact your specialist dealer.



For instructions

on how to change the batteries, see the installation manual.



It is recommended to unplug the battery charger from the mains when not in use. This is

to prevent unnecessary energy consumption.

 If appliances stay plugged into the USB port

while charging the electronic wheelchair, the

battery will never charge fully. Therefore, unplug all appliances from the USB port before

charging the wheelchair.

The light emitting diode (LEDs) in the steering unit indicates the remaining capacity of your

batteries. If the battery charger is turned on and no LED's are lit, check the fuse. If the red LED

does not illuminate, the charger is defective.Consult your specialist dealer.

1. Switch the scooter OFF and remove the key.

2. FIRST connect the battery charger to a 230V AC power socket.

3. Refer to the battery charger manual for the explication of the indicators on the charger.

4. If applicable, open the cover of the charging point on the scooter.

5. Connect the charger.

6. Refer to the battery-charger manual for the explication of the indicators on the charger.

7. When the battery is fully loaded, disconnect the scooter from the charger.

8. Switch the scooter ON and check if all lights of the battery status indicator are ON.

9. Remove the charger from the socket, let it cool down and store it in a dry location.

When the operating console displays the warning

code “Drive inhibit” after charging, make

sure that the battery charger is disconnected. This safety measure prevents driving with the

charger still connected to the supply grid.

CAUTION

1 = Key

2 = USB connection

3 = Socket battery charger

1

2

3

Mercurius 4D

2021-02

Using your scooter

16

EN

NL

3.8 Thermal fuses

To protect the motor against overload, your scooter

has a thermal safety mechanism on the rear. The

thermal fuse will automatically cut off the motor to

prevent overheating and thus rapid wear and tear

or breakdowns. You can access the thermal safety

device through a gap in the back of the synthetic

cover.

The thermal safety device can be activated if you

go up or down slopes that exceed the maximum

specified gradient. Nominal loads that exceed the

permitted maximum could also cause the device to

jump out. Likewise, if you keep on driving with the

engine brake on, it could result in overload. The maximum values not to exceed are indicated in

§6.

To be able to use the scooter again, remove the overload and wait until the motor has cooled

down. Then gently press the thermal safety mechanism back in. Your scooter is now ready for

use again.

3.9 Anti-tipping

An anti-tipping (1) is fixed to the frame of the scooter

on the rear side. It is not possible to remove these.

The anti-tipping is there for your safety. It prevents

the scooter from tipping over backward when you

drive over small obstacles that do NOT exceed the

maximum height as specified in §6.

1

La page charge ...

Vermeiren Mercurius 4D Manuel utilisateur

Vermeiren Mercurius 4D Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents