Greenlee 975 Hydraulic Pump Serial Code TZ Manual Manuel utilisateur

INSTRUCTION MANUAL

Read and understand all of the instructions and

safety information in this manual before operating

or servicing this tool.

Register this product at www.greenlee.com

975

Hydraulic Power Pump

Serial Code TZ

Español: p. 27

Français: p. 53

975 Hydraulic Power Pump

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

2

Description

Greenlee 975 Hydraulic Power Pump is an electrically

powered two-stage pump that develops a maximum of

700 bar (10,000 psi). This pump is intended to provide

hydraulic power for an accessory with a single-acting

ram such as a Greenlee conduit bender or cable cutter.

This pump has a factory-set internal pressure relief

valve.

Fill unit with hydraulic oil before oper-

ating pump.

Failure to ll unit with oil will result in

damage to the pump

Safety

Safety is essential in the use and maintenance of

Greenlee tools and equipment. This instruction manual

and any markings on the tool provide information for

avoiding hazards and unsafe practices related to the

use of this tool. Observe all of the safety information

provided.

Purpose of this Manual

This manual is intended to familiarize all personnel with

the safe operation and maintenance procedures for the

following Greenlee 975 (Serial Code TZ).

Keep this manual available to all personnel.

Replacement manuals are available upon request at no

charge at www.greenlee.com.

All specications are nominal and may change as design

improvements occur. Greenlee Tools, Inc. shall not be liable for

damages resulting from misapplication or misuse of its products.

732 is a trademark of Dow Corning.

Loctite and Ultra Blue are registered trademarks of Loctite

Corporation.

Mobil DTE is a registered trademark of Mobil Oil Corporation.

KEEP THIS MANUAL

Table of Contents

Description .................................................................... 2

Safety ............................................................................ 2

Purpose of this Manual ................................................. 2

Important Safety Information ..................................... 3-4

Specications ................................................................ 5

Setup

Hydraulic Connection ................................................ 6

Electrical Connection/Grounding Instructions ........... 6

Operation ....................................................................... 7

Maintenance ............................................................... 8-9

Troubleshooting ...................................................... 10-15

Service ................................................................... 16-18

Repairs ................................................................... 19-21

Exploded Views ...................................................... 22-23

Parts List ................................................................ 24-26

975 Hydraulic Power Pump

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

3

IMPORTANT SAFETY INFORMATION

SAFETY

ALERT

SYMBOL

This symbol is used to call your attention to hazards

or unsafe practices which could result in an injury or

property damage. The signal word, dened below,

indicates the severity of the hazard. The message

after the signal word provides information for pre-

venting or avoiding the hazard.

Immediate hazards which, if not avoided, WILL result

in severe injury or death.

Hazards which, if not avoided, COULD result in

severe injury or death.

Hazards or unsafe practices which, if not avoided,

MAY result in injury or property damage.

Read and understand all of the

instructions and safety information

in this manual before operating or

servicing this tool.

Failure to observe this warning will

result in severe injury or death.

Do not connect the pump to any system or system

component other than those supplied by Greenlee.

Other manufacturer’s components may not withstand

the maximum pressure and may fail. Nearby person-

nel can be injured by ying components and hydraulic

oil.

Failure to observe this warning will result in severe

injury or death.

Do not alter the internal high-pressure relief valve

setting. Altering this setting will change the maximum

pressure the pump can develop, which can cause a

component failure. Nearby personnel can be injured

by ying components and hydraulic oil.

Failure to observe this warning will result in severe

injury or death.

Do not use this pump in a hazardous

environment. Hazards include am-

mable liquids, gases, or other materi-

als. Using this pump in a hazardous

environment can result in a re or

explosion.

Failure to observe these warnings will

result in severe injury or death.

975 Hydraulic Power Pump

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

4

Electric shock hazard:

• Do not expose power tools to rain.

• Do not immerse the pendant switch

in water or other liquid.

Failure to observe these warnings can

result in severe injury or death.

Skin injection hazard:

High pressure oil easily punctures

skin causing serious injury, gangrene,

or death. If injured, seek medical help

immediately to remove oil.

• Do not use ngers or hands to

check for leaks.

• Depressurize hydraulic system

before servicing or disconnecting

the hose.

Wear eye protection when using this

tool.

Failure to wear eye protection can

result in serious eye injury from ying

debris or hydraulic oil.

Inspect pump, hoses, couplers, and ttings for wear

or damage. Replace worn, damaged or missing com-

ponents with Greenlee replacement parts. Worn or

damaged components can fail, resulting in injury.

Failure to observe this warning can result in severe

injury or death.

Fill unit with hydraulic oil before oper-

ating pump.

Failure to ll unit with oil will result in

damage to the pump

• The pump is heavy and requires two persons to lift.

Improper lifting can result in injury.

• Do not use hose or cord to pull, lift, or carry the

equipment. Misuse will damage the hose or cord.

Failure to observe these precautions can result in

injury or property damage.

Make sure all hose ttings are properly seated before

starting the pump. Incomplete connections may not

allow the accessory’s ram to retract after the hydrau-

lic operation is nished.

Note: Keep all decals clean and legible, and replace

when necessary.

IMPORTANT SAFETY INFORMATION

975 Hydraulic Power Pump

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

5

Speciﬁcations

Motor

Voltage ........................................................................................................ 120 VAC

Frequency ........................................................................................................60 Hz

Current .......................................................................................................... 9 amps

Power .......................................................................................................1080 watts

Revolutions per minute ..................................................................................... 3600

Pump Output

Power ........................................................................................... 373 watts (1/2 hp)

Hydraulic pressure (maximum) ...................................................700 bar (10,000 psi)

(pressure relief valve setting)

Hydraulic Fluid Capacity*

Full ................................................................................................ 5.7 liters (6 quarts)

Usable ..........................................................................................2.8 liters (3 quarts)

Hydraulic Fluid Speciﬁcations (Mobil DTE

®

13M)

Viscosity ........................................................... 30 cSt at 40 °C (150 SSU at 100 °F)

6 cSt at 100 °C (46 SSU AT 210 °F)

Viscosity Index .................................................................................................... 145

Pour Point .......................................................................................... -40 °F (-40 °C)

Typical Performance

Pressure Volume

0 .........................................................................................4.9 liter/min (300 in

3

/min)

6.9 bar (100 psi) .................................................................3.6 liter/min (225 in

3

/min)

345 bar (5000 psi) ..............................................................0.31 liter/min (19 in

3

/min)

552 bar (8000 psi) ..............................................................0.29 liter/min (18 in

3

/min)

Dimensions

Length ..................................................................................................305 mm (12")

Width .................................................................................................... 254 mm (10")

Height ................................................................................................ 394 mm (15.5")

Weight/Mass ..........................................................................................23 kg (51 lb)

975 Hydraulic Power Pump

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

6

Setup

Hydraulic Connection

1. Clean all couplers, threaded ttings, ports and the

area around all ports.

2. Remove any dust plugs from couplers.

3. Hand-tighten all couplings rmly (until all threads are

fully engaged). Do not use tools.

Electrical Connection

Electric shock hazard:

• Do not modify the plug provided

with the tool.

• Connect this tool to a grounded

receptacle on a 15-amp GFCI-

protected circuit.

Failure to observe these warnings can

result in severe injury or death.

This tool must be grounded. In the event of a malfunc-

tion or breakdown, an electrical ground provides a path

of least resistance for the electric current. This path of

least resistance is intended to reduce the risk of electric

shock.

This tool’s electric cord has a grounding conductor

and a grounding plug as shown. Do not modify the

plug. Connect the plug to a corresponding 15-amp

GFCI-protected receptacle that is properly installed

and grounded in accordance with all national and local

codes and ordinances. Do not use an adapter.

ReceptaclePlug

Extension Cord Specications:

Diameter .........................................1.5 mm

2

(14 AWG)

Length .......................................... 30 meters (100 feet)

Use only three-wire extension cords. Use of an

inadequate extension cord will cause the motor to stall.

975 Hydraulic Power Pump

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

7

Operation

Skin injection hazard:

High pressure oil easily punctures

skin causing serious injury, gangrene,

or death. If injured, seek medical help

immediately to remove oil.

• Do not use ngers or hands to

check for leaks.

• Depressurize hydraulic system

before servicing or disconnecting

the hose.

Procedure for depressurizing the hydraulic system:

1. Disconnect the pump from the power source.

2. Rotate the release lever to AUTO RELEASE and

allow the ram to retract fully.

3. Disconnect the hose slowly to release any

trapped pressure.

Note: To prevent leakage, this pump was shipped with

an unvented plug installed in the reservoir ﬁll hole. This

plug must be replaced with the attached vented plug

(6) before use. Failure to replace the unvented plug will

cause poor performance.

Note: Starting the motor without a tool attached to

the pump will cause the pump to immediately build an

internal pressure of 700 bar (10,000 psi). If this happens,

shut off the pump and turn the release valve to AUTO

RELEASE to release the hydraulic pressure.

1. Move release valve lever to the AUTO RELEASE

position.

2. Check reservoir oil level. The oil level should be

within 25 mm (1 inch) of the top of the reservoir. If oil

level is too low, see Adding Oil in the Maintenance

section for instructions.

3. Place release valve lever in desired position:

• AUTO RELEASE – ram will stop and then retract

when the hand switch or foot switch is released.

• MANUAL RELEASE – ram will stop but will not

retract when the hand switch or foot switch is

released.

4. Press the hand switch or foot switch to advance

the hydraulic ram. When nished, release the hand

switch or foot switch.

Note: If release valve lever is in the MANUAL

RELEASE position, the ram will not retract. To

retract ram, rotate the release valve lever to the

AUTO RELEASE position.

975 Hydraulic Power Pump

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

8

Maintenance

Procedure for depressurizing the hydraulic system:

1. Disconnect the pump from the power source.

2. Rotate the release lever to AUTO RELEASE and

allow the ram to retract fully.

3. Disconnect the hose slowly to release any

trapped pressure.

Every time the pump is used

• Check the oil reservoir level. The oil level should be

approximately 25 mm (1 inch) from the top of the res-

ervoir. If the oil level is low, see Adding Oil.

• Examine the condition of the hose, connectors, and

O-rings for deterioration, wear, or other damage.

Replace any missing or damaged components.

• Check the condition of all electrical cords, plugs, and

connectors.

• Listen for unusual noises and observe the operation

of the pump for changes in performance. Either situ-

ation may indicate that maintenance or repairs are

necessary.

Periodically

• Examine the hydraulic oil for changes in color

or viscosity, and the presence of dirt or other

contamination.

• Occasionally check oil temperature after pump is

operated. The recommended operating temperature is

38 °C to 50 °C (100 °F to 125 °F).

Cleaning

• Periodically clean the exterior of the pump and

motor. Use a vacuum cleaner to clean the ventilation

openings.

• Clean the area around the reservoir vent, and be sure

the vent breather hole is open.

• Keep all hose connections clean and use protective

caps or plugs when couplers are not in use.

Oil Condition

Visual inspection of the oil may be used as a guide

to determine the need to replace the oil. A change in

appearance, such as darkening or thickening, will indi-

cate a need for replacement. The continued use of oil

after it should be replaced will cause accelerated wear

of system components and will void the warranty.

Adding Oil

Do not use brake uid. Brake uid will ruin the seals.

1. Place control lever in AUTO RELEASE position.

2. Unplug the electrical cord from the power source.

3. Thoroughly clean the area around the ll hole.

4. Remove the vented reservoir plug.

5. Use Greenlee hydraulic uid or an equivalent high-

grade light hydraulic oil. See the “Parts List” section

of this manual for Greenlee hydraulic oil specica-

tion and Greenlee part number.

6. Pour the oil through a clean funnel with lter screen.

7. Add oil until oil level is 25 mm (1 inch) from the top

of the reservoir cover.

975 Hydraulic Power Pump

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

9

Maintenance (cont’d)

Purging (Bleeding) Air

When purging air from the system:

• Do not advance the ram more than 3/4 of its stroke.

Overextending the ram will allow hydraulic uid

to leak out, and the ram may damage the O-rings

when it retracts.

• Do not restrict the ram travel to run the pump up

to full pressure (commonly called dead heading the

pump).

Failure to observe these precautions can result in

injury or property damage.

Erratic performance may indicate air in the hydraulic

system.

1. Remove the ram from the accessory (conduit

bender frame, cable cutter, etc.).

2. If possible, position the pump so that it is located

higher than the ram. This will allow air to travel up

the hydraulic hose to the pump reservoir.

3. Place the ram in a vertical position with the hose

coupler upward.

4. Rotate the control lever counterclockwise (to

MANUAL RELEASE).

5. Start the pump and, using the ram scale as a refer-

ence, advance the ram 3/4 of its stroke. Stop the

pump. Do not overextend the ram!

6. Rotate the control lever clockwise (to AUTO

RELEASE). The ram will retract, forcing any air out

through the hose, into the pump reservoir, and

through the vented plug.

7. Check the oil level of the reservoir. Add oil

if necessary.

Draining and Flushing the System

Note: Thoroughly clean the pump exterior before

removing the reservoir.

1. Remove the reservoir cover screws.

2. Remove the pump system from the reservoir.

Note: Be careful not to damage the cover gasket,

inlet strainer or relief valve when removing the

pump.

3. Clean the interior of the reservoir and ll with clean

kerosene. Do not use solvents. Rinse the inlet

strainer.

4. Place the pump system into the reservoir and

replace the four cover screws.

5. Connect a hose to the pump as usual. Insert the

other end of the hose into the pump reservoir at ll

hole.

6. Run the pump for several minutes. While the

pump is running, rotate the control lever between

MANUAL RELEASE and AUTO RELEASE several

times. Start and stop the pump several times to

cycle the pilot-operated valve.

7. Remove the hose and remove the pump assembly

from the reservoir. Drain and clean the reservoir inte-

rior. Allow the reservoir to dry. Drain the hose.

8. Reassemble the pump system.

9. Rell reservoir as instructed under the Adding Oil

instructions in this section.

Motor Maintenance

Disconnect the pump from the power source before

servicing or cleaning the motor. The exposed motor

bearings and shaft should be cleaned periodically.

Lubrication

Lubricate the motor according to the motor

manufacturer’s instructions, located on the

motor's nameplate or terminal box.

975 Hydraulic Power Pump

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

10

Problem Probable Cause Probable Remedy

Motor will not start. No power to motor. Plug electric cord in to a properly

rated power source. Unplug cord

and inspect the contacts. Clean

contacts if necessary.

Replace the electric cord.

Replace switch cord or ON/OFF

switch.

Motor is damaged or worn out. Replace motor.

Motor will not start under load. Voltage supplied to motor is too low. Unplug cord and check power

source with a voltmeter. The voltage

should be 120 VAC (+/– 10%).

Current rating of extension cord is

too low.

See the extension cord specica-

tions under Electrical Connection in

the Setup section of this manual.

Pilot-operated valve will not open,

will not open fully, or opens too

slowly.

See “Troubleshooting—Pilot-

Operated Valve” at the end of this

troubleshooting section.

Motor starts, but stops when it

encounters a load.

Voltage supplied to motor is too low. Unplug cord and check power

source with a voltmeter. The voltage

should be 120 VAC (+/– 10%).

Current rating of extension cord is

too low.

See the extension cord specica-

tions under Electrical Connection in

the Setup section of this manual.

Motor is overheated. Let motor cool. Do not run motor

continuously in a hot environment.

Misalignment of the motor shaft and

low pressure pump drive shaft.

Replace reservoir cover plate (22).

The counterweight needs

adjustment.

See Motor Face Seal, Figure

A1, for the correct setting of the

counterweight.

Motor is damaged or worn out. Replace motor.

Troubleshooting—Hydraulic Pump

Repair work must be done by qualied personnel famil-

iar with this equipment.

If possible, use a hand pump to apply back pressure

when checking for leaks.

How to use this table: If your hydraulic pump does not

operate properly, nd the description of the problem

under the “Problem” column. Read the Probable Cause

and the Probable Remedy. Begin with solution listed

rst, and proceed through all of the solutions until the

problem is solved. Where repairs are necessary, see the

appropriate schematic and item listed in the “Probable

Remedy” column.

975 Hydraulic Power Pump

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

11

Problem Probable Cause Probable Remedy

Ram will not advance.

Ram advances slowly.

Ram will not advance completely.

Low-pressure system has a partial or

complete failure.

See Hydraulic Schematic (1,3,7)

and refer to Figure A4 in the Repairs

section of this manual.

Unvented plug has not been

replaced.

Remove the unvented plug and

install the vented plug.

Oil level is too low. Add oil per instructions in the

Maintenance and Service section of

this manual.

Wrong oil viscosity. Replace oil with the type recom-

mended in the Specications section

of this manual.

Oil is dirty. Replace oil with the type recom-

mended in the Specications section

of this manual.

Oil is cold. Preheat oil. Without an acces-

sory connected to the coupler, run

the pump to build pressure, then

release. Repeat until oil is warm.

The intake strainer is dirty or

clogged.

Remove the strainer and clean with

kerosene.

Motor rotates in the wrong direction. Correct the motor wiring. See the

Motor Control, Schematic Diagram

in the Motor Control Unit section of

this manual.

Low-pressure relief valve is dirty or is

set incorrectly.

To clean and adjust this valve, see

Low-Pressure Relief Setting, Figure

A4 in the Repairs section of this

manual.

Broken internal part. Inspect and/or replace drive pin (78),

motor shaft key (34), rollpin (39), or

drive shaft (77).

Worn or damaged internal part. Inspect and/or replace the gerotor

(80); eccentric shaft (38), or bearings

(37 and/or 41).

Pilot-operated valve will not close. See “Troubleshooting—Pilot-

Operated Valve” at the end of this

troubleshooting section.

Internal hydraulic uid leak. Inspect and replace as necessary:

O-ring plug (79) and pump block

cover (50).

Troubleshooting—Hydraulic Pump (cont’d)

975 Hydraulic Power Pump

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

12

Problem Probable Cause Probable Remedy

Ram advances erratically and

retracts erratically.

Air in the hydraulic uid. Refer to Purging (Bleeding) Air in the

Maintenance and Service section of

this manual.

Pump will not build enough

pressure to complete the job.

Ram advances slowly.

High-pressure system is faulty. See Hydraulic Schematic (5) and

refer to Figure A5-1 in the Repairs

section of this manual.

System has an external hydraulic

leak.

Visually inspect hoses, connectors

and ttings for leaking hydraulic

uid. Replace faulty components.

Pilot-operated valve will not close. See “Troubleshooting—Pilot-

Operated Valve” at the end of this

Troubleshooting section.

Low-pressure system is at fault. Find “Low-pressure system partial

or complete failure” under Probable

Causes in this Troubleshooting

section.

At high-pressure inlet, the check ball

has too much travel.

See Check Ball Travel at High

Pressure Inlet, Figure A5-1. If the

seats are leaking, see Ball Seat

Renishing, Figure B2 in the Repairs

section of this manual.

The high-pressure piston is stuck. Disassemble, clean, and inspect the

high-pressure bushing (75) and high-

pressure piston (76). Replace parts

as necessary.

Internal hydraulic uid leak. Inspect and replace as necessary:

O-ring Plug (68)

Cavity Insert (74)

High-Pressure Bushing (75)

High-Pressure Relief Valve (72)

High-pressure relief valve failure. Readjust, re-seat or replace valve

(72).

Troubleshooting—Hydraulic Pump (cont’d)

975 Hydraulic Power Pump

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

13

Problem Probable Cause Probable Remedy

Ram will not hold pressure. System has an external leak. Visually inspect hoses, connectors

and ttings for leaking hydraulic

uid. Replace faulty components.

Manual control valve needs

adjustment or repair.

See Hydraulic Schematic (8) and

refer to Figures A2 and A3 in the

Repairs section of this manual

The manual control valve is not in

correct position.

Rotate the manual control valve to

AUTO RELEASE position.

The manual control valve needs to

be adjusted.

See Manual Release/Automatic

Release Valve Handle Setting, Figure

A3 in the Repairs section of this

manual.

Check ball does not seat properly. See Manual Release/Automatic

Release Valve Handle Setting, Figure

A2, and Ball Seat Renishing, Figure

B4 in the Repairs section of this

manual.

Ram will not retract. The manual control valve is not in

correct position.

Rotate the manual control valve to

AUTO RELEASE position.

The manual control valve needs to

be adjusted.

Adjust the handle. See Manual

Release/Automatic Release Valve

Handle Setting, Figure A3 in the

Repairs section of this manual.

Quick-couplers are not fully

threaded together.

Disconnect the hydraulic hoses and

clean the couplings. Reconnect

the hydraulic hoses. Hand-tighten

couplings rmly until all threads are

engaged. Do not use a wrench.

Manual control valve set incorrectly. See Hydraulic Schematic (8) and

refer to Figures A2 and A3 in the

Repairs section of this manual.

The pilot-operated valve will not

open, will not open fully, or opens

too slowly.

See “Troubleshooting—Pilot-

Operated Valve” at the end of this

Troubleshooting section.

Hydraulic cylinder of the accessory

has failed.

Troubleshoot the accessory that is

connected to the pump.

Troubleshooting—Hydraulic Pump (cont’d)

975 Hydraulic Power Pump

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

14

Troubleshooting—Pilot-Operated Valve

Problem Probable Cause Probable Remedy

Pilot-operated valve will not open.

Pilot-operated valve will not open

fully. Pilot-operated valve opens too

slowly.

The pilot piston does not return

freely.

See Hydraulic Schematic (7) and

refer to Low-Pressure Relief Setting,

Figure A4 in the Repairs section of

this manual.

Oil is cold. Preheat oil. Without an accessory

connected to the coupler, run the

pump to build pressure, then release.

Repeat until oil is warm.

Wrong oil viscosity. Replace oil with the type recom-

mended in the Specications section

of this manual.

Oil is dirty. Replace oil with the type recom-

mended in the Specications section

of this manual.

Pilot piston components may be

worn or damaged.

Clean and inspect items 42-49.

Replace parts as necessary.

Low-pressure bypass check valve is

set incorrectly.

See Hydraulic Schematic (4).

If set too low: The pump cannot

shift to the high-pressure stage. See

Pressure Adjustment for the Low-

Pressure Bypass Check, Figure A5 in

the Repairs section of this manual.

If set too high: The pump cannot

restart under pressure. See Pressure

Adjustment for the Low-Pressure

Bypass Check, Figure A5 in the

Repairs section of this manual.

The ball seat of the low-pressure

bypass check-valve is damaged.

See Ball Seat Renishing, Figure B2

in the Repairs section of this manual.

975 Hydraulic Power Pump

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

15

Troubleshooting—Pilot-Operated Valve (cont’d)

Problem Probable Cause Probable Remedy

Pilot-operated valve will not close. A particle of dirt or some other

foreign object is holding the low-

pressure bypass check valve open.

Disassemble, clean and inspect

spring (70) and 9/32" ball (71).

Replace parts as necessary.

Low-pressure bypass check valve is

faulty.

See Hydraulic Schematic (4).

If set too low: The pump cannot

shift to the high-pressure stage. See

Pressure Adjustment for the Low-

Pressure Bypass Check, Figure A5 in

the Repairs section of this manual.

If set to high: The pump cannot

restart under pressure. See Pressure

Adjustment for the Low-Pressure

Bypass Check, Figure A5 in the

Repairs section of this manual.

The ball seat of the low-pressure

bypass check valve is damaged.

See Ball Seat Renishing, Figure B2,

B3 and B4 in the Repairs section of

this manual.

Low-pressure bypass check ball

seat is oversized.

Replace the pump block (84).

A particle of dirt or some other

foreign object is holding the low-

pressure relief valve open.

Disassemble, clean and inspect

the valve piston (48), spring (47),

ball (46), spring (45) and stem (44).

Replace parts as necessary.

Low-pressure relief valve is set too

low.

See Low-Pressure Relief Setting,

Figure A4 in the Repairs section of

this manual.

Low-pressure bypass check ball

seat is damaged.

See Ball Seat Renishing in the

Repairs section of this manual.

Figures B2, B3, and B4.

Low-pressure bypass check seat is

oversized.

Replace the pump block (84).

The pilot piston does not advance

freely

See Hydraulic Schematic (7).

See Low-Pressure Relief Setting,

Figure A4 in the Repairs section of

this manual. Clean and inspect items

42-49. Replace parts as necessary.

Valve seat is damaged. See Hydraulic Schematic (3, 7).

975 Hydraulic Power Pump

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

16

Service

Motor Control Unit

4

20

16

85

90

86

8 50323636

87

89

88

Pendant Switch Control Wiring

GREEN

WIRE LEAD

(GROUND)

MOTOR

TOP VIEW

WHITE

WIRE LEAD

POWER

CORD

WHITE

WIRE LEAD

(POWER)

BLACK

WIRE LEAD

PENDANT

SWITCH CORD

Pendant Switch Wiring

WHITE

L1

MOTOR CONNECTIONS

L2

WHITE

BLACK

WHITE

L1

GREEN

GROUND

PENDANT

SWITCH

WIRING

INCOMING LINE

L2

BLACK

975 Hydraulic Power Pump

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

17

Service (cont’d)

Motor Control Unit

115V Franklin Electric

3X #10

ORANGE

BLUE

RED

VIOLET

L1

4

L2

3

115V General Electric

4 3 2 1

L2

#6

4X #8

L1

WHITE

BLACK

YELLOW

RED

ORANGE

975 Hydraulic Power Pump

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

18

Service (cont’d)

Hydraulic Schematic

6

8

7

3

4

9

5

2

1

Intake strainer, #50 mesh brass screen

2

Low-pressure pump

5.5 liters/min. (335 in

3

/min) at 3600 rpm (100%)

3

Low-pressure relief valve — 19 bar (275 psi) located

in pilot-operated valve

7

Piston

4

Low-pressure bypass check valve

5

High-pressure pump

.37 liters/min. (22.5 in

3

/min) at 3450 rpm (100%)

6

High-pressure relief valve

717/700 bar (10,400/10,000 psi)

7

Pilot-operated directional control valve

3 way, 2 position

8

Manually operated check valve

9

Female coupler half

Sealing Instructions for Assembly

Motor

If the motor has been disassembled, seal with a 3 mm

(1/8") bead of a silicone-based gasket/ange sealant,

such as Loctite

®

587 Ultra Blue

®

, as follows:

(A) To the mounting surface around the threads

(four locations)

(B) To the chamfer (four locations)

(C) Around the innermost machined circumference of

the mounting surface

Apply a 1.5 mm (1/16") bead of an RTV-type sili-

cone-based sealant, such as Dow Corning 732™

Multipurpose Sealant, as follows:

(D) Around the motor bearing screws (two locations)

Assemble immediately.

A

B

D

C

Driv-Lok Pin

Seal the Driv-Lok pin (73) to the pump block (84) with

a 1.5 mm (1/16") bead of an RTV-type silicone-based

sealant, such as Dow Corning 732™ Multipurpose

Sealant or equivalent.

73

84

975 Hydraulic Power Pump

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

19

Repairs

The following section and Figures describe pertinent

details for renishing ball seats and component

re-assembly and adjustments.

Motor Face Seal

When reassembling the motor, refer to Figure A1 for the

face seal seating dimension. Also, refer to this gure for

setting the vertical position of counterweight (32).

22

21

MOTOR SHAFT

MOTOR FACE

4.6mm (.180 inch)

4.1mm (.160 inch)

32

8

6mm (.234 inch)

Figure A1

Manual Release/Automatic Release Valve

Handle Setting

Refer to Figures A2 and A3. Thread in the shaft (62) until

it just touches the check ball (55) (in its spring-loaded

closed position). Slide collar (104) on the shaft. Position

the handle (61) at the location “Position 1,” (Figure A3),

with the other surface of the handle ush with the end of

the shaft. Lock in place. Rotate the handle to “Position

2,” (Figure A3). Slide the collar toward the valve body

until it contacts the 15.9 mm (5/8") diameter portion of

the control shaft. Rotate the lock collar clockwise until it

touches the stop pin, and lock in place.

When locking control handle and lock collar in

place, torque set screws tight to 2.8–3.4 Nm

(25–30inch-pounds).

54

55

60

62

104

61

Figure A2

7.938 mm (0.312") ø BALL SEAT

STOP

8

45

STOP

CLOSED

STOP

OPEN

BALL OPEN

112.5 (.99 mm [.039"])

POSITION 2

SET POSITION #1

22.5 (REF.)

135

Figure A3

8

975 Hydraulic Power Pump

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

20

Repairs (cont’d)

Low Pressure Relief Setting

Refer to Figure A4. Lightly bottom the stem (44) on the

ball (46). Then, back out the stem 3-1/2 turns. Tighten

nut (43). The resulting pressure setting should be

approximately 19.3 bar (280 psi).

44

3

Figure A4

7

42

47

43

45

46

49

48

Low-Pressure Bypass Check Pressure Adjustment

When properly set to the dimension shown in Figure A5,

the high pressure stage operation of the pump will be

delayed approximately one (1) second after the motor

starts. This delay is created by the closing time of the

pilot-operated valve.

Note: This dimension must be increased if ball seat

depth is increased by more than .4 mm (1/64 inch).

Increasing the bypass pressure (CW rotation of adjust-

ing screw—increase of set dimension) will shorten delay.

If delay becomes too short, the motor will not restart

when high pressure is held in the line. The motor should

restart with a maximum required off time of 1/2 to 1

second.

Decreasing the bypass pressure (CCW rotation of

adjusting screw) will increase delay. The pilot-operated

valve will not close if pressure is set too low.

Changes in oil temperature (viscosity) will affect the

amount of delay. The pumping delay will increase with

rising oil temperature (thinner oil).

COVERPLATE

36.17 mm (1.424")

8 mm (5/16") Ø BALL

(used to make measurement)

37.29 mm (1.468")

69

70

71

4

Figure A5

High-Pressure Inlet Check Ball Travel

The amount of allowable ball travel is critical to the

optimum high pressure output (ow rate). Refer to

Figure A5-1. Carefully and accurately measure (depth

“mike”) the “A” dimension (top of pump block to seated

ball) and “B” dimension (top of pump block to head of

plug—at center). Carefully and accurately set the “C”

dimension (overall length of assembled plug and pin) of

a new plug and pin equal to “A” minus “B” minus .305 ±

.050 mm (.012 ± .002 inches).

TOP OF

PUMP BLOCK

A

5

Figure A5-1

C

B

TRAVEL

.305 mm +/– .050 mm

(.012 inch +/– .002 inch)

42

79

105

Low Pressure Pump Drive Pin

Assemble with cone point end in half-round keyway.

78

Figure A6

La page charge ...

Greenlee 975 Hydraulic Pump Serial Code TZ Manual Manuel utilisateur

Ce manuel convient également à

Greenlee 975 Hydraulic Pump Serial Code TZ Manual Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents