Yamaha cc 70 Manuel utilisateur

Yamaha
Marque
Yamaha
Modèle
cc 70
Catégorie
Lecteurs de cassettes
Taper
Manuel utilisateur
Active Servo
Technology
CC-70W is composed of RX-S70, CDC-S90, KXW-S70 and NX-S70.
CC-70S is composed of RX-S70, CDC-S90, KX-S90 and NX-S70.
* For U.K. and Europe models, NX-S70 is optional in some areas.
Natural Sound Mini Component System
CC-70W
/
CC-70 S
OWNER’S MANUAL
Page
SAFETY INSTRUCTIONS.......................Inside Front Cover-1
INTRODUCTION....................................................................2
FEATURES............................................................................2
SUPPLIED ACCESSORIES...................................................2
PRECAUTIONS..................................................................2-3
NAMES OF CONTROLS, INDICATORS AND
REAR PANEL PARTS.........................................................4-6
REMOTE CONTROL TRANSMITTER................................7-9
REMOVING THE FRONT GRILLE
(for Speaker System NX-S70 only).........................................9
PREPARATION FOR USE..............................................10-11
OPEN/CLOSE THE CONTROL DOOR................................12
TURNING THE POWER ON/OFF TO THIS SYSTEM.........12
SETTING THE CLOCK.........................................................13
SOUND CONTROL..............................................................14
Page
COMPACT DISC PLAYER OPERATION........................14-21
TUNING OPERATION.....................................................22-24
TAPE DECK OPERATION
(for KXW-S70 Double Cassette Deck) ............................25-28
TAPE DECK OPERATION
(for KX-S90 Single Cassette Deck).................................29-31
RECORDING COMPACT DISCS....................................32-37
OTHER RECORDINGS...................................................38-39
HOW TO USE THE BUILT-IN TIMER.............................40-43
USING EXTERNAL UNITS .............................................44-45
MAINTENANCE....................................................................45
SPECIFICATIONS................................................................46
TROUBLESHOOTING..........................................................47
ACTIVE SERVO TECHNOLOGY
(for Speaker System NX-S70 only).......................................48
CONTENTS
IMPORTANT!
Please record the serial number of this unit in the
space below.
Model:
Serial No.:
The serial number is located on the rear of the
unit.
Retain this Owner’s Manual in a safe place for
future reference.
1 Read Instructions – All the safety and operating
instructions should be read before the unit is operated.
2 Retain Instructions – The safety and operating instructions
should be retained for future reference.
3 Heed Warnings – All warnings on the unit and in the
operating instructions should be adhered to.
4 Follow Instructions – All operating and other instructions
should be followed.
5 Water and Moisture – The unit should not be used near
water – for example, near a bathtub, washbowl, kitchen
sink, laundry tub, in a wet basement, or near a swimming
pool, etc.
6 Carts and Stands – The unit should be used only with a
cart or stand that is recommended by the manufacturer.
6A A unit and cart combination should be
moved with care. Quick stops,
excessive force, and uneven surfaces
may cause the unit and
cart combination to overturn.
7 Wall or Ceiling Mounting – The unit
should be mounted to a wall or ceiling only as
recommended by the manufacturer.
8 Ventilation – The unit should be situated so that its
location or position does not interfere with its proper
ventilation. For example, the unit should not be situated
on a bed, sofa, rug, or similar surface, that may block the
ventilation openings; or placed in a built-in installation,
such as a bookcase or cabinet that may impede the flow
of air through the ventilation openings.
9 Heat – The unit should be situated away from heat
sources such as radiators, stoves, or other appliances
that produce heat.
10 Power Sources – The unit should be connected to a
power supply only of the type described in the operating
instructions or as marked on the unit.
11 Power-Cord Protection – Power-supply cords should be
routed so that they are not likely to be walked on or
pinched by items placed upon or against them, paying
particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the unit.
12 Cleaning – The unit should be cleaned only as
recommended by the manufacturer.
13 Nonuse Periods – The power cord of the unit should be
unplugged from the outlet when left unused for a long
period of time.
14 Object and Liquid Entry – Care should be taken so that
objects do not fall into and liquids are not spilled into the
inside of the unit.
15 Damage Requiring Service – The unit should be serviced
by qualified service personnel when:
A. The power-supply cord or the plug has been damaged;
or
B. Objects have fallen, or liquid has been spilled into the unit;
or
C. The unit has been exposed to rain; or
D. The unit does not appear to operate normally or exhibits a
marked change in performance; or
E. The unit has been dropped, or the cabinet damaged.
16 Servicing – The user should not attempt to service the unit
beyond those means described in the operating
instructions. All other servicing should be referred to
qualified service personnel.
17 Power Lines – An outdoor antenna should be located
away from power lines.
18 Grounding or Polarization – Precautions should be taken
so that the grounding or polarization is not defeated.
19 Outdoor Antenna Grounding – If an outside antenna is
connected to this unit, be sure the antenna system is
grounded so as to provide some protection against
voltage surges and built-up static charges. Article 810 of
the National Electrical Code, ANSI/NFPA 70, provides
information with regard to proper grounding of the mast
and supporting structure, grounding of the lead-in wire to
an antenna discharge unit, size of grounding conductors,
location of antenna discharge unit, connection to
grounding electrodes, and requirements for the grounding
electrode.
SAFETY INSTRUCTIONS
(for U.S. customers)
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead
symbol, within an equilateral triangle,
is intended to alert you to the
presence of uninsulated “dangerous
voltage” within the product’s
enclosure that may be of sufficient
magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an
equilateral triangle is intended to alert
you to the presence of important
operating and maintenance
(servicing) instructions in the
literature accompanying the
appliance.
•
Explanation of Graphical Symbols
CAUTION
WARNING
TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE THIS
UNIT TO RAIN OR MOISTURE.
1. IMPORTANT NOTICE : DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the
instructions contained in this manual, meets FCC
requirements. Modifications not expressly approved by
Yamaha may void your authority, granted by the FCC, to
use the product.
2. IMPORTANT : When connecting this product to
accessories and/or another product use only high quality
shielded cables. Cable/s supplied with this product
MUST be used. Follow all installation instructions.
Failure to follow instructions could void your FCC
authorization to use this product in the USA.
3. NOTE : This product has been tested and found to
comply with the requirements listed in FCC Regulations,
Part 15 for Class “B” digital devices. Compliance with
these requirements provides a reasonable level of
assurance that your use of this product in a residential
environment will not result in harmful interference with
other electronic devices.
This equipment generates/uses radio frequencies and, if
not installed and used according to the instructions
found in the users manual, may cause interference
harmful to the operation of other electronic devices.
Compliance with FCC regulations does not guarantee that
interference will not occur in all installations. If this product
is found to be the source of interference, which can be
determined by turning the unit “OFF” and “ON”, please try
to eliminate the problem by using one of the following
measures:
Relocate either this product or the device that is being
affected by the interference.
Utilize power outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the
antenna. If the antenna lead-in is 300 ohm ribbon lead,
change the lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory
results, please contact the local retailer authorized to
distribute this type of product. If you can not locate the
appropriate retailer, please contact Yamaha Electronics
Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA
90620.
The above statements apply ONLY to those products
distributed by Yamaha Corporation of America or its
subsidiaries.
Note to CATV system installer:
This reminder is provided to call the CATV system
installer's attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in
particular, specifies that the cable ground shall be
connected to the grounding system of the building, as
close to the point of cable entry as practical.
YAMAHA and the Electronic Industries Association’s
Consumer Electronics Group want you to get the most out of
your equipment by playing it at a safe level. One that lets the
sound come through loud and clear without annoying blaring
or distortion – and, most importantly, without affecting your
sensitive hearing.
Since hearing damage from loud sounds is often
undetectable until it is too late, YAMAHA and the
Electronic Industries Association’s Consumer
Electronics Group recommend you to avoid
prolonged exposure from excessive volume levels.
We Want You Listening For A Lifetime
FCC INFORMATION
1
SPECIAL NOTES FOR FCC COMPOSITE
DEVICE
This device is a composite system. The digital device
component may not cause harmful interference.
Remote control transmitter AM (MW/LW) loop antenna
Indoor FM antenna
Batteries (size AA, UM/SUM-3, R6,
HP-7)
Speaker cords (for NX-S70)
PRECAUTIONS: READ THIS BEFORE OPERATING YOUR UNIT
2
After unpacking, check that the following parts are contained.
INTRODUCTION
FEATURES
SUPPLIED ACCESSORIES
Thank you for purchasing this YAMAHA product. We hope it will give you many years of trouble-free enjoyment. For the best
performance, read this manual carefully. It will guide you in operating your YAMAHA product.
This Owner’s Manual covers two models of tape deck, KXW-S70 and KX-S90. So please check the model name of your tape
deck and use this owner’s manual effectively excluding unnecessary information.
For U.K. and European customers, the speaker system NX-S70 is optional in some areas. If your system does not include NX-
S70, its information on this manual is not also needed.
•
3-CD Carousel Auto Changer
•
PLAYXCHANGE: Disc Changing Capability while
Playing Another
•
Random Access Programmable CD Playback
•
Single Track/Entire Disc/All Disc Repeat Play
•
3-Disc Random Play
•
Automatic Synchronized Recording with CD
Playback
•
Automatic CD Editing Function for Recording to
Tape
•
Continuous Tape Playback Capability by
Automatic Reversing Function
•
Dolby B/C Noise Reduction System
•
40 Station Automatic Preset Tuning
•
Multi-Use Timer/Sleep Timer
•
Active Servo Processing Speaker System
(NX-S70)
•
Remote Control Capability
■ To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
■ [Except for U.K. and Europe models]:
This system is equipped with the newly developed Active Servo
Processing Speaker System. It is not designed for use with
conventional speakers. Therefore, do not attempt to connect
other speakers than the provided speaker system.
■ Choose the installation location of this unit carefully. Avoid placing
it in direct sunlight or close to a source of heat. Also avoid
locations subject to vibration and excessive dust, heat, cold or
moisture. Keep it away from sources of hum such as transformers
and electric motors.
■ Do not operate this unit upside-down. It may overheat, possibly
causing damage.
■ Never open the cabinet. If something drops into the set, contact
your dealer
■ The openings on the cabinet assure proper ventilation of the unit.
If these openings are obstructed, the temperature inside the
cabinet will rise rapidly and eventually damage the circuits.
Therefore, avoid placing objects against these openings and do
not install the unit where the flow of air through the ventilation
openings could be impeded.
■ Always set the VOLUME control to “0” before starting the audio
source play: increase the volume gradually to an appropriate level
after the play has been started.
■ When not planning to use this unit for long periods of time (ie.,
vacation, etc.), disconnect the AC power plug from the wall outlet.
-
+
12345
12345
678
67890
ABCDE
TIME
PROG
TAPE EDIT
+
I0
SEARCH
SKIP
STOP
PLAY/PAUSE
DISC SKIP
RANDOM REPEAT
CD
TUNER
TAPE
PRESET A/B/C/D/E
DOWN UP
PLAY STOP PLAY
REC/PAUSE
SLEEPPOWER
DISPLAY
VOLUME
DECK
PHONO/AUX
TUNER DIRECT
A/B
PRECAUTIONS: READ THIS BEFORE OPERATING YOUR UNIT
■ Grounding or polarization – Precautions should be taken so that
the grounding or polarization of an appliance is not defeated.
■ Do not use force on switches, controls or connection wires. When
moving the unit, first disconnect the power plug and the wires
connected to other equipment. Never pull the wire itself.
■ Do not attempt to clean the unit with chemical solvents; this might
damage the finish. Use a clean, dry cloth.
■ Be sure to read the “TROUBLESHOOTING” section regarding
common operating errors before concluding that the unit is faulty.
■ To prevent lightning damage, disconnect the AC power plug and
the antenna cable when there is an electrical storm.
■ Do not plug the AC power plug to the wall socket before you
finish all connections.
■ Never allow metallic items (e.g. screwdrivers, tools, etc.) to come
near the cassette deck’s record/playback head assembly in this
unit. Doing so may not only scratch or damage the head’s mirror-
smooth finish, it may change the magnetic characteristics of the
heads, causing a deterioration in reproduction performance
quality.
■ Although the cassette deck’s record/playback heads used in this
unit are high quality heads with outstanding reproduction
characteristics, they can become dirty through the use of old
tapes or from dust accumulation over time. This can have a
serious effect on reproduction quality. Clean the heads regularly
with one of the commonly available head cleaners or with
cleaning solutions.
■ The voltage to be used must be the same as that specified on
this unit. Using this product with a higher voltage than that which
is specified is dangerous and may result in a fire or other type of
accident causing damage. YAMAHA will not be held responsible
for any damage resulting from use of this unit with a voltage other
than that which is specified.
■ The sound level at a given volume setting depends on a
combination of speaker efficiency, location and many other
factors. Care should be taken to avoid exposure to sudden high
levels of sound, which may occur when turning on the unit with
the volume control setting at high, and to continuous high levels
of sound.
■ Sudden temperature changes and storage or operation in an
extremely humid environment may cause condensation inside the
cabinet.
Condensation can cause the unit to malfunction.
Follow the procedure below to eliminate condensation.
•
CD pickup
Leave the power on with no disc in the unit until normal
playback is possible (about 1 hour).
•
Tape head
Leave the power on with no cassette in the unit until normal
playback is possible (about 1 hour).
Note
If condensation forms on the tape head, foreign matter may
accumulate during use.
•
Remote control
Wipe off condensation on the transmitter window with a soft
cloth before operating the unit.
3
DANGER
Invisible laser radiation when open and interlock failed or
defeated. Avoid direct exposure to beam.
CAUTION 1
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
CAUTION 2
As the laser beam used in this compact disc player is harmful to
the eyes, do not attempt to disassemble the cabinet. Refer
servicing to qualified personnel only.
Laser component in this product is capable of emitting radiation
exceeding the limit for Class 1.
IMPORTANT
The wire in the mains lead are coloured in accordance with the
following code:
Blue: NEUTRAL
Brown: LIVE
The colours of the wires in the mains lead of this apparatus
may not correspond with the coloured markings identifying the
terminals in your plug. Proceed as follows: the wire which is
coloured BLUE must be connected to the terminal which is
marked with the letter N or coloured BLACK. The wire which is
coloured BROWN must be connected to the terminal which is
marked with the letter L or coloured RED. Making sure that
neither core is connected to the earth terminal of the three pin
plug.
This compact disc player is
classified as a CLASS 1 LASER
product.
The CLASS 1 LASER PRODUCT
label is located on the rear exterior.
(Europe and U.K. model only)
Laser Diode Properties
•
Material: GaAlAs
•
Wavelength: 780nm
•
Emission Duration: continuous
•
Laser Output: max. 44.6µW*
* This output is the value measured at a distance of about 200mm
from the objective lens surface on the Optical Pick-up Block.
SPECIAL INSTRUCTIONS FOR U.K. MODEL
For U.K. customers
If the socket outlets in the home are not suitable for the plug supplied
with this appliance, it should be cut off and an appropriate 3 pin plug
fitted. For details, refer to the instructions described below.
Note: The plug severed from the mains lead must be destroyed, as a
plug with bared flexible cord is hazardous if engaged in a live socket
outlet.
CLASS 1 LASER PRODUCT
APPAREIL À LASER DE CLASSE 1
PRODUCTO LASER DE CLASE 1
WARNING
To reduce the risk of fire or electric shock, do not expose this unit to
rain or moisture.
To avoid electrical shock, do not open the cabinet. Refer
servicing to qualified personnel only.
NOTE
Please check the copyright laws in your country to record from
records, compact discs, radio, etc. Recording of copyright material
may infringe copyright laws.
CAUTION FOR CARRYING THE CD PLAYER
Be sure not to carry or tip the CD player with discs remaining in it.
4
NAMES OF CONTROLS, INDICATORS AND REAR PANEL PARTS
CD Player (CDC-S90)
1. Disc Table
2. Stop Button:
3. Play/Pause Button: /
4. Disc Select Buttons
5. TIME Button
6. EDIT Button
7. REPEAT Button
8. RANDOM Play Button
9. SKIP Buttons: /
(SEARCH Buttons: / )
10. PLAYXCHANGE Button
11. OPEN/CLOSE Button:
12. Disc Indicator
13. Tape Side Indicator
14. EDIT Indicator
15. Track Number Indicator
16. Time Display
17. (S, F, A) REPEAT Indicator
18. RANDOM Play Indicator
19. PROGRAM Indicator
20. Music Calendar Indicator
21. Music Calendar OVER Indicator
22. Play Indicator:
Receiver (RX-S70)
23. SLEEP Indicator
24. TIMER Set Indicator
25. Preset Number Indicator
26. Station Frequency Indicator
27. MEMORY Indicator
28. Band Indicator
29. AUTO TUNING Indicator
30. STEREO Indicator
31. POWER Switch
32. Remote Control Sensor
33. Input Selector Buttons
34. VOLUME Control
35. PHONES Jack
36. DISPLAY Button
37. TUNER PRESET DOWN/UP Buttons
38. A/B/C/D/E (TIMER) Button
39. MEMORY (TIME ADJUST) Button
40. Tuning DOWN (HOUR) Button
41. Tuning UP (MINUTE) Button
42. AUTO/MAN’L (SEC) Button
43. BAND Selector Button
44. AUTO MEMORY Button
45. BASS Tone Control
46. TREBLE Tone Control
47. BALANCE Control
45678
1
9
23
10 11
31 32 33 34
35
36
37
38
39
40
41
42
43
44
45
46
47
For CD Player
For Receiver
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
OVER
AB
TRACK TOTAL REMAIN
SFA REP
RANDOM
PROG
EDIT
STEREO
AUTO TUNING
PRESET
MHz
MEMORY
SLEEP
TIMER
12 13 14 15 16 17 18 19
23 24 25 26
27 28 29 30
20 21 22
5
NAMES OF CONTROLS, INDICATORS AND REAR PANEL PARTS
Double Cassette Tape Deck (KXW-S70)
48. DECK A Cassette Compartment
49. DECK A Select Button and Indicator
50. DECK B Select Button and Indicator
51. DECK B Cassette Compartment
52. Stop Button:
53. Play Direction Indicator
54. DECK A EJECT Button
55. Fast Wind Button:
56. Play Button:
57. Reverse Mode Switch
58. DUBBING (NORMAL/HIGH) Buttons and
Indicators
59. REC/PAUSE Button and Indicator
60. Dolby NR Switch
61. Play Button:
62. Fast Wind Button:
63. DECK B EJECT Button
64. Play Direction Indicator
65. PLAY Indicator
Single Cassette Tape Deck (KX-S90)
66. Fast Wind Button:
67. Cassette Compartment
68. Play Button and Play Direction Indicator:
69. Stop Button:
70. Play Button and Play Direction Indicator:
71. Fast Wind Button:
72. PLAY Indicator
73. REC Indicator
74. OPEN/CLOSE Button:
75. RESET Button
76. Tape Counter (LINEAR COUNTER)
77. REMAIN Indicators
78. Dolby NR Switch
79. Reverse Mode Switch
80. REC/PAUSE Button
Speakers (NX-S70)
(For U.K. and Europe models, NX-S70 is optional in
some areas.)
81. YST Port
82. Speaker Terminals
48 49 50 51
52
53
54
55
56
57
58 59
60
61
62
63
64
65
EMPTY
66 67 68 69 70 71 72 73 74
75 76 77 78 79 80
81
82
6
NAMES OF CONTROLS, INDICATORS AND REAR PANEL PARTS
FREQUENCY STEP switch (General model only)
Because the interstation frequency spacing differs in
different areas, set the FREQUENCY STEP switch
(located at the rear) according to the frequency spacing in
your area. Before setting this switch, disconnect the AC
supply lead of this unit from the AC outlet.
Rear Panel of Receiver
1. Antenna Terminals
2. INPUT (PHONO and AUX) Terminals
3. SPEAKERS SELECTOR Switch
(U.K. and Europe models only)
4. GND Terminal
5. SPEAKERS Terminals
6. VOLTAGE SELECTOR (General model only)
7. FREQUENCY STEP Switch (General model only)
8. System Control Sockets
9. AC Supply Lead
VOLTAGE SELECTOR (General model only)
The voltage selector on the rear panel of this unit must
be set for your local main voltage BEFORE plugging
into the AC main supply.
Voltages are 110/120/220/240V AC, 50/60 Hz.
Rear Panel of Cassette Tape Deck
10. System Control Connector
SPEAKERS SELECTOR switch (U.K. and Europe
models only)
If you connect YAMAHA NX-S70 speaker system to this
unit, set this switch to “NX-S70”.
If you connect a speaker system other than NX-S70 to this
unit, set this switch to “CONVENTIONAL”.
Rear Panel of CD Player
11. System Control Connector
7
Names of control buttons
■
Receiver Control Buttons
1. Remote Control Transmitter Window
2. Preset Station Number Buttons
3. A, B, C, D, E Selector Buttons
4. PRESET DOWN/UP Buttons
5. A/B/C/D/E Button
6. POWER Switch
7. SLEEP Button
8. DISPLAY Button
9. VOLUME Down (–)/Up (+) Buttons
10. Input Selector Buttons
■ CD Player Control Buttons
11. Track Number Input Buttons
12. TIME Button
13. SEARCH Buttons: /
(SKIP Buttons: / )
14. DISC SKIP Button
15. RANDOM Button
16. REPEAT Button
17. STOP Button:
18. PLAY/PAUSE Button:
19. EDIT Button
20. TAPE Button
21. PROGRAM Button
REMOTE CONTROL TRANSMITTER
-
+
12345
12345
678
67890
ABCDE
TIME
PROG
TAPE EDIT
+
I0
SEARCH
SKIP
STOP
PLAY/PAUSE
DISC SKIP
RANDOM REPEAT
CD
TUNER
TAPE
PRESET A/B/C/D/E
DOWN UP
PLAY STOP PLAY
REC/PAUSE
SLEEPPOWER
DISPLAY
VOLUME
DECK
PHONO/AUX
TUNER DIRECT
A/B
2
3
4
5
678 9
10
1
12345
12345
678
67890
ABCDE
TIME
PROG
TAPE EDIT
+
I0
SEARCH
SKIP
STOP
PLAY/PAUSE
DISC SKIP
RANDOM REPEAT
CD
TUNER DIRECT
11
12
21
20
19
18
13
14 15 16 17
8
■
Tape Deck Control Buttons
22. Play Button:
23. Stop Button:
24. Play Button:
25. Fast Wind Button:
26. DECK A/B Select Buttons (for KXW-S70 only)
27. Fast Wind Button:
28. REC/PAUSE Button:
Loading the batteries for the
remote control transmitter
1 Remove the battery compartment cover.
(Press the left edge of the cover to right with a finger, and
then pull it upward.)
2 Insert 2 “AA” size batteries (UM/SUM-3, R6, HP-7 or
equivalent) into the battery compartment.
* Installing the batteries improperly may cause failure.
3 Replace the battery compartment cover.
Precautions for battery use
•
Insert the batteries according to the direction indicated in
the battery compartment.
•
Replace all batteries with new ones at the same time.
•
Remove the batteries if they are weak or if the unit is not
in use for long periods.
•
Don’t mix normal batteries with rechargeable batteries.
2
1
3
REMOTE CONTROL TRANSMITTER
-
+
TAPE
PLAY STOP PLAY
REC/PAUSE
SLEEPPOWER
DISPLAY
VOLUME
DECK
PHONO/AUX
A/B
27
28
22 23 24 25 26
9
Proper use of the remote control
transmitter
Aim (within the range of 60° with no obstacles) the remote
control transmitter at the remote control sensor and operate
as shown.
Notes concerning use
•
Replace the batteries if control distance decreases or
operation becomes unstable.
•
Periodically clean the transmitter window on the remote
control transmitter and the sensor on the main unit with a
soft cloth.
•
Exposing the sensor on the main unit to strong light
(especially an inverter type of fluorescent lamp etc.) may
interfere with operation. In this case, reposition the main
unit to avoid direct lighting.
•
Keep the remote control transmitter away from moisture,
excessive heat, shock and vibrations.
•
The remote control transmitter’s usable range is within
0.2m (8”) and 6m (20’) away from the sensor.
The front grille is fastened to the enclosure at four points, and
can be removed if desired. To remove the grille, hold on to
both sides and slowly pull straight away from the speaker. To
reattach, line up the four pegs on the speaker with the four
corresponding holes on the inside surface of the grille and
push gently.
Note
When the grille is removed, take care not to touch the
speaker units with your hands or to exert excessive force
with tools.
REMOTE CONTROL TRANSMITTER
REMOVING THE FRONT GRILLE (for Speaker System NX-S70 only)
10
Placing the system
This system can be placed any way you like, however, be
sure not to place another unit or any object on top of the
receiver to prevent the ventilation holes on the top panel of
the receiver from being obstructed. If doing so, the receiver
may be damaged.
Notes
•
If the system is put in a rack, allow a space of at least 5
cm (1-15/16”) above and behind the unit.
•
Disconnect the AC supply lead from the AC outlet before
connecting or disconnecting any component.
Antenna connection
(1) Supplied FM antenna
Connect the FM antenna wire to the corresponding terminal
and direct the FM antenna wire to the direction where the
strongest signal can be received.
(2) Supplied AM (MW/LW) loop antenna
Connect the AM (MW/LW) loop antenna wire to the
corresponding terminals. Position the AM (MW/LW) loop
antenna for optimum reception. Place the AM (MW/LW) loop
antenna on a shelf etc., or install it on the rack or wall with
screws (not supplied).
Notes
•
When static is still heard even after adjusting the position
of the AM (MW/LW) loop antenna, try reversing the
connection (top to bottom).
•
Do not place the AM (MW/LW) loop antenna on the unit. It
will result in noise generation, since the unit is equipped
with digital electronics. Place the AM (MW/LW) loop
antenna away from the unit.
(3) External FM antenna
Use an external FM antenna instead of an indoor FM
antenna if you need better reception. Consult your dealer.
(4) External AM (MW/LW) antenna
Use an external AM (MW/LW) antenna if you need better
reception. Consult your dealer.
Note
When using an external AM (MW/LW) antenna, be sure to
keep the wire of the AM (MW/LW) loop antenna connected.
PREPARATION FOR USE
* For U.K. and Europe models, “AM” is replaced by
“MW LW”.
RX-S70 CDC-S90
KXW-S70 or KX-S90
KXW-S70 or KX-S90
RX-S70
CDC-S90
Placing examples
or
Earth rod
7.5 m (25 feet)
15 m (49 feet)
11
Speaker connection
Connect each speaker wire to the SPEAKERS terminals.
Cautions
•
Do not let the bare speaker wires touch each other as this
could damage the receiver and/or speakers.
•
When connecting the speakers to the unit, be sure to
connect the speaker wires properly. Do not mistake the
right channel for the left channel and the plus (+) terminal
for the minus (–) terminal.
•
[For U.S.A., Canada, Australia and General models]
Do not connect these SPEAKERS terminals to speakers
other than the provided speaker system NX-S70.
•
[For U.K. and Europe models]
Set the SPEAKERS SELECTOR switch on the rear panel
of the receiver to the proper position before connections.
If you use YAMAHA Active Servo Processing Speaker
System NX-S70, set this switch to “NX-S70”.
If you use a speaker system other than NX-S70, set this
switch to “CONVENTIONAL”.
System connection
•
Connect the red connector on the rear of CDC-S90 to the
red socket on the rear of RX-S70.
•
Connect the black connector on the rear of KXW-S70 (or
KX-S90) to the black socket.
How to disconnect the system connector
Grasp both sides of the connector to disconnect the
connector.
Connecting the AC supply lead
•
After connecting the speakers and system connectors,
plug the AC supply lead into a convenient AC outlet.
•
Unplug the AC supply lead from the AC outlet if the unit is
not to be used for a long period of time.
PREPARATION FOR USE
For connecting with NX-S70
(Black wire with white line → plus (+) terminal,
black wire → minus (–) terminal)
To an AC outlet
12
OPEN/CLOSE THE CONTROL DOOR
When it is not necessary to operate controls inside the
control door, close the door.
To open or close the door, press the right edge until it clicks.
STANDBY mode
While the power is on, pressing the POWER switch (or the
POWER switch on the remote control transmitter) switches
the system to the STANDBY mode. (In this mode, the
display shows only the time.) In this mode, main voltage is
still present inside the system. If you want to switch off the
system completely, disconnect the AC power plug from the
AC outlet.
TURNING THE POWER ON/OFF TO THIS SYSTEM
If the AC supply lead is connected to the AC outlet, this
system can be turned ON and OFF (STANDBY mode) by
pressing the POWER switch on the front panel of the
receiver or the POWER button on the remote control
transmitter.
13
1 While the power is on, press the DISPLAY button to
display the time. If the power is off, you can proceed to the
next step.
2 While pressing the TIME ADJUST button, press the
HOUR button and set the hour.
* Press the HOUR button once to advance the time by 1
hour. Press and hold to advance continuously.
3 While pressing the TIME ADJUST button, press the
MINUTE button and set the desired time.
* Press the MINUTE button once to advance the time by
1 minute. Press and hold to advance continuously.
* The hour setting will not advance even if the minute
advance from “59” to “00”.
To display the time by “second”
While pressing the SEC button, the current time is displayed
by minute and second.
To reset the second to “00”
While pressing the SEC button, press the TIME ADJUST
button.
* If the current second is lower than 30, it is reset to 00.
* If the current second is higher than 30, the minute is
advanced by 1 minute and the second is reset to 00.
(If the current minute is “59”, in this case, the hour is also
advanced by 1 hour.)
In the event of a power failure or when the AC supply
lead is disconnected.
The time display will go out, however, the clock will function
for about 30 minutes without power supply. So you do not
have to reset the time if the AC power supply is resumed
within about 30 minutes.
When the AC power supply is resumed after more than 30
minutes pass without power supply, the time display will flash
on and off to indicate that the time must be reset.
Note
If this system is left for several minutes without setting the
time after the AC power lead of this system is connected to
the AC outlet, there may be a case that the display is turned
into a demonstration mode. (This mode is virtually
unnecessary for using this system.)
In this case, first turn the power on by pressing the POWER
switch to cancel the mode, and then set the time.
SETTING THE CLOCK
Changes.
Changes.
1
2
3
14
COMPACT DISC PLAYER OPERATION
VOLUME
0I0
-
+
VOLUME
SOUND CONTROL
Volume
Front panel operation
Rotate the VOLUME control towards 10 to increase the
volume, and towards 0 to decrease the volume.
Remote control operation
Press the VOLUME + button to increase the volume and the
VOLUME – button to decrease the volume.
Balance
Adjust the balance of the output volume to the left and right
speakers to compensate for sound imbalance caused from
the speaker settings or the listening room condition.
Turn this clockwise to emphasize the right and
counterclockwise for the left.
Tone
BASS : Turn this clockwise to increase (or counter-
clockwise to decrease) the low frequency
response.
TREBLE : Turn this clockwise to increase (or counter-
clockwise to decrease) the high frequency
response.
BALANCE
LR
BASS TREBLE
–+–+
Care of compact discs
Compact discs are fairly resistant to damage, however
mistracking can occur due to an accumulation of dirt on the
disc surface.
Follow the guidelines below for maximum enjoyment from
your CD collection and player.
•
Do not write on either side of the disc, particularly the non-
label side. Signals are read from the non-label side. Do
not mark this surface.
•
Keep your discs away from direct sunlight, heat and
excessive moisture.
•
Always hold the CDs by the edges. Fingerprints, dirt or
water on the CDs can cause noise or mistracking. If a CD
is dirty or does not play properly, clean it with a soft, dry
cloth, wiping straight out from the center, along the radius.
15
CD playback
1 Press the CD input selector button.
2 Press the OPEN/CLOSE button to open the disc table.
3 Place discs on the trays, label side up.
* Up to three discs can be loaded on the trays.
* 8 cm (3”) discs may be played without an adaptor.
4 Press the OPEN/CLOSE button to close the disc table.
* The total number of tracks and the total playing time of
the disc being selected will be displayed for several
seconds.
* The music calendar will be displayed only for the
number of tracks on the disc being selected.
* If the compact disc contains more than 20 tracks, the
“OVER” indicator will light up on the music calendar.
5 If necessary, select another disc by pressing the DISC
SKIP button on the remote control transmitter once or
more (so that the corresponding disc tray number is
located on top of the disc indicator).
6 Press the play/pause button to start playback from track 1.
* The “ ” indicator will appear and playback will begin.
As the playback of each track on the music calendar is
finished, that track number will go out.
For easier operation
Pressing the disc select button (1, 2 or 3) will select the disc
directly, and playback will begin from track 1 automatically.
To interrupt playback
11 Press the play/pause button.
* The “ ” indicator will flash.
22 Press the play/pause button to resume playback from the
same point.
To stop playback
Press the stop button.
To switch the unit off after use
Turn the unit off by pressing the POWER switch. (The
indicators will go off except for the current time display.)
COMPACT DISC PLAYER OPERATION
POWER
POWER
Total number of tracks
The disc on the tray located on top of this
indicator is now being selected.
Music calendar Total playing time
Disc select buttons
Receiver
CD Player
1
2, 4
1
5
3
6, 11, 22
6, 11, 22
1 2 3 4 5 6 7 8 9 10 11 12
TRACK TOTAL
16
-
+
ABCD
TIME
PROG
TAPE EDIT
SEARCH
SKIP
STOP
PLAY/PAUSE
DISC SKIP
RANDOM REPEAT
CD
TUNER
TAPE
PRESET A/B/C/D/E
DOWN UP
PLAY STOP PLAY
REC/PAUSE
SLEEPPOWER
DISPLAY
VOLUME
DECK
PHONO/AUX
A/B
12345
12345
678
67890
E
+
I0
TUNER DIRECT
12345
12345
678
67890
E
+
I0
TUNER DIRECT
COMPACT DISC PLAYER OPERATION
Direct operation
Even when an input source other than CD player is selected,
pressing the play/pause button, a disc select button, a track
number input button or the RANDOM play button, or pressing
the front edge of the disc table gently will start playback
directly. In this case, if the tape deck is playing back a tape,
it will be stopped automatically.
* These ways of playback can also be used to close the disc
table. If the table is closed in these ways, playback will
begin automatically, however, the display will not show the
total number of tracks and the total playing time of the disc
to be played.
PLAYXCHANGE
During playback, you can open the disc table by pressing the
PLAYXCHANGE button without interrupting disc playback.
However, in this case, pressing the DISC SKIP button on the
remote control transmitter has no effect.
Precautions
•
If TV or radio interference occurs during CD player
operation, move the unit away from the TV or radio.
•
Subjecting the unit to shock or vibration can cause
mistracking.
•
Playing some compact discs at high volume can cause
mistracking. In this case, listen at lower volume.
•
Do not push the disc table while it is moving.
•
If the power fails while the table is open, wait until the
power supply returns or gently push the table manually to
close it.
•
The temperature range for playing compact discs is
recommended to be 5°C (41°F) – 35°C (95°F).
Direct-selection play
By using the track number input buttons on the remote
control transmitter, any track you wish to listen to can be
played directly.
Use the track number input buttons to select the desired
track number. Play will begin automatically.
A. For example, to choose selection 5
Press the “5” button.
B. For example, to choose selection 12
(1)Press the “+10” button.
(2)Within 3 seconds, press “2” button.
C. For example, to choose selection 20
(1)Press the “+10” button.
(2)Within 3 seconds, press the “+10” button again.
(3)Within 3 seconds, press the “0” button.
Note
A track number higher than the number of tracks on the disc
cannot be selected. Also, if a higher track number is selected
while the disc table is open, play will begin from the last track
on the disc when the disc table is closed.
17
COMPACT DISC PLAYER OPERATION
“Skip search” and “Manual search” are performed using the
same buttons.
Skip search
The beginning of any track can be found automatically.
1 Select a disc and begin playback.
2 Press the button to advance or button to
reverse through the disc.
Press once for each track to be advanced or reversed.
•
Press once to advance to the track following the
one now playing back.
•
Press once to return to the start of the track now
playing back.
•
Press twice to return to the track before the track
now playing back.
Notes
•
This function can also be performed while the unit is
stopped. Press the play/pause button when your desired
track number appears in the track number display.
Playback will begin from the beginning of the track.
•
This function will be performed forward or backward from
any point on the disc. However, it will not move forward
during playback of the final track.
Manual search
1 Begin playback.
2 Press and hold the button to advance play rapidly,
and the button to reverse play rapidly.
*
The sound can be heard (although slightly garbled)
during manual search in either direction. This is
convenient for reviewing the contents quickly.
Note
Manual search can also be performed while playback is
paused, though no sound will be heard.
CD Player
1
2
1
2
18
COMPACT DISC PLAYER OPERATION
Program play
You can program up to 20 tracks in any desired order.
1 Load discs and close the disc table.
2 When in the stop mode, press the PROGRAM button to
prepare for programming.
* “PROG” and “P-01” illuminate on the display, and all
track numbers on the selected disc begin flashing.
3 If necessary, select a desired disc by pressing the DISC
SKIP button.
4 Use the track number input buttons to select the desired
track number.
* The selected track number and the total play time of
the programmed tracks will illuminate on the display,
and soon it is replaced by the display of the next
playback order. Programmed track numbers on the
selected disc will stop flashing and illuminate on the
music calendar.
* Pressing the TIME button displays the total play time of
the programmed tracks for about 1 second, and then it
is replaced by the display of the next playback order.
* For example, to choose selection 12
(1)Press the “+10” button.
(2)Within 3 seconds, press the “2” button.
5 Repeat steps 3 and 4 for any other track. Up to 20 tracks
can be programmed.
6 Press the play/pause button to start playback of
programmed tracks.
Notes
•
It is also possible to program a sequence of tracks while
looking at the list of tracks on the surface of the disc
before closing the disc table.
•
During playback or pause, programming is not possible.
•
If the total time of the programmed tracks reaches 100
minutes or more, only the last two-digits will be displayed
for the three-digit number.
•
The total time of the programmed tracks will not be
displayed, if a track number higher than 19 is
programmed.
•
Skip search can be performed during playing back, but
only within the range of the programmed tracks.
•
Manual search can be performed during playing back to
search through all tracks, including unprogrammed tracks.
•
If programs are made selecting tracks from more than one
disc, pressing the PLAYXCHANGE button is useless
during program play.
Playback order
Music calendar
Selected disc Total playing time
Display information during programming
Selected track number
-
+
12345
12345
678
67890
ABCDE
TIME
PROG
TAPE EDIT
+
I0
SEARCH
SKIP
STOP
PLAY/PAUSE
DISC SKIP
RANDOM REPEAT
CD
TUNER
TAPE
PRESET A/B/C/D/E
DOWN UP
PLAY STOP PLAY
REC/PAUSE
SLEEPPOWER
DISPLAY
VOLUME
DECK
PHONO/AUX
TUNER DIRECT
A/B
CD Player
6 1
6
4
2
3
1 2 3 4 5 6 7 8 9 10 11 12
TRACK
PROG
1 2 3 4 5 6 7 8 9 10 11 12
TRACK TOTAL
PROG
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51

Yamaha cc 70 Manuel utilisateur

Yamaha
Marque
Yamaha
Modèle
cc 70
Catégorie
Lecteurs de cassettes
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents