JVC KD-G152 Le manuel du propriétaire

Catégorie
Récepteurs multimédia de voiture
Taper
Le manuel du propriétaire
ENGLISH
FRANÇAIS
CD RECEIVER
RECEPTEUR CD
KD-S1501/KD-G152/KD-G151
For installation and connections, refer to the separate manual.
Pour l’installation et les raccordements, se référer au manuel séparé.
INSTRUCTIONS
MANUEL D’INSTRUCTIONS
GET0287-003A
[EX/EU]
For canceling the display demonstration, see page 7.
Pour annuler la démonstration des affichages, référez-vous à la page 7.
Cover_KD-S1501[EX_EU]f.indd 2Cover_KD-S1501[EX_EU]f.indd 2 10/27/04 3:21:20 PM10/27/04 3:21:20 PM
2
ENGLISH
Thank you for purchasing a JVC product.
Please read all instructions carefully before operation, to ensure your complete understanding and to
obtain the best possible performance from the unit.
IMPORTANT FOR LASER PRODUCTS
1. CLASS 1 LASER PRODUCT
2. CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave
all servicing to qualified service personnel.
3. CAUTION: Visible and invisible laser radiation when open and interlock failed or defeated.
Avoid direct exposure to beam.
4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED OUTSIDE THE UNIT.
Warning:
If you need to operate the receiver while
driving, be sure to look ahead carefully or
you may be involved in a traffic accident.
How to reset your unit
This will reset the microcomputer. Your
preset adjustments will also be erased.
If a disc is loaded, it will eject. Be careful
not to drop the disc.
How to forcibly eject a disc
If a disc cannot be recognized by the
receiver or cannot be ejected, ejects the disc
as follows.
If this does not work, try to reset your
receiver.
Be careful not to drop the disc when it
ejects.
Note: Only for [EX] model users in UK and European countries
For security reasons, a numbered ID card is provided with this receiver, and the same ID number is
imprinted on the receiver’s chassis. Keep the card in a safe place, as it will help the authorities to
identify your receiver if stolen.
EN02-05_KD-S1501[EX_EU]f.indd 2EN02-05_KD-S1501[EX_EU]f.indd 2 10/27/04 3:22:05 PM10/27/04 3:22:05 PM
3
ENGLISH
How to reset your unit ........................... 2
How to forcibly eject a disc ................... 2
How to read this manual ........................ 4
How to use the MODE button ............... 4
Control panel — KD-S1501/
KD-G152/KD-G151 ................... 5
Parts identification ................................. 5
Getting started ....................... 6
Basic operations .................................. 6
Canceling the display demonstrations ... 7
Setting the clock .................................... 7
Radio operations ................... 8
Listening to the radio ........................... 8
Storing stations in memory .................... 9
Listening to a preset station ................... 9
FM RDS operations ................. 10
Searching for your favorite FM RDS
programme
....................................... 10
Storing your favorite programmes ......... 11
Using the standby receptions ................. 11
Tracking the same programme
—Network-Tracking Reception ........ 12
Disc operations ...................... 13
Playing a disc ..................................... 13
Selecting the playback modes ................ 14
Sound adjustments ................ 15
Selecting preset sound modes
(C-EQ: custom equalizer) .................. 15
Adjusting the sound ............................... 16
General settings — PSM ......... 17
Basic procedure ..................................... 17
Detaching the control
panel .................................. 19
Maintenance .......................... 20
More about this receiver ........ 21
Troubleshooting ..................... 22
Specifications ......................... 23
*For safety....
Do not raise the volume level too much, as
this will block outside sounds, making driving
dangerous.
Stop the car before performing any
complicated operations.
Contents
*Temperature inside the car....
If you have parked the car for a long time in
hot or cold weather, wait until the temperature
in the car becomes normal before operating the
unit.
EN02-05_KD-S1501[EX_EU]f.indd 3EN02-05_KD-S1501[EX_EU]f.indd 3 10/27/04 3:22:06 PM10/27/04 3:22:06 PM
4
ENGLISH
How to read this manual
The following methods are used to made the
explanations simple and easy-to-understand:
Some related tips and notes are explained in
“More about this receiver” (see page 21).
Button operations are mainly explained with
the illustrations as follows:
Press briefly.
Press repeatedly.
Press either one.
Press and hold until
your desired response
begins.
Press and hold both
buttons at the same
time.
How to use the MODE button
If you press MODE, the receiver goes into
functions mode, then the number buttons work
as different function buttons.
Ex.: When number button 2 works as
MO (monaural) button.
Time countdown indicator
To use these buttons for original functions
again after pressing MODE, wait for
5 seconds without pressing any of these buttons
until the functions mode is cleared.
Pressing MODE again also clears the
functions mode.
EN02-05_KD-S1501[EX_EU]f.indd 4EN02-05_KD-S1501[EX_EU]f.indd 4 10/27/04 3:22:06 PM10/27/04 3:22:06 PM
5
ENGLISH
Control panel — KD-S1501/KD-G152/KD-G151
Display window
1 +/– buttons
2 DISP (display) button
3 Loading slot
4 Display window
5 MODE button
6 0 (eject) button
7
¢/4 buttons
8
(standby/on/attenuator) button
9 SEL (select) button
p EQ (equalizer) button
q MO (monaural) button
w SSM (Strong-station Sequential Memory)
button
e CD button
r FM/AM button
t RPT (repeat) button
y RND (random) button
u T/P (traffic programme/programme type)
button
i
(control panel release) button
o Number buttons
Display window
; Tuner reception indicators
MO (monaural), ST (stereo)
a RDS indicators
TP, PTY, AF, REG
s CD indicator
d RND
(disc random) indicator
f RPT (repeat) indicator
g LOUD (loudness) indicator
h EQ (equalizer) indicator
j Sound mode (C-EQ: custom equalizer)
indicators
ROCK, CLASSIC, POPS, HIP HOP, JAZZ,
USER
also works as the time countdown
indicator.
k Main display
l Source display
Volume level indicator
Parts identification
EN02-05_KD-S1501[EX_EU]f.indd 5EN02-05_KD-S1501[EX_EU]f.indd 5 10/27/04 3:22:07 PM10/27/04 3:22:07 PM
6
ENGLISH
Getting started
Basic operations
~
Ÿ
You cannot select “CD” as the playback
source if there is no disc in the loading
slot.
!
Volume level appears.
Volume level indicator
Adjust the sound as you want.
(See pages 15 and 16.)
To drop the volume in a moment (ATT)
To restore the sound, press it
again.
To turn off the power
Caution on volume setting:
Discs produce very little noise compared
with other sources. Lower the volume
before playing a disc to avoid damaging
the speakers by the sudden increase of the
output level.
EN06-11_KD-S1501[EX_EU]f.indd 6EN06-11_KD-S1501[EX_EU]f.indd 6 10/27/04 3:22:49 PM10/27/04 3:22:49 PM
7
ENGLISH
Canceling the display
demonstrations
If no operations are done for about 20 seconds,
display demonstration starts.
[Initial: DEMO ON]—see page 17.
1
2
3
4
Finish the procedure.
To activate the display demonstration
In step 3 above...
Setting the clock
1
2
Set the hour, minute, and clock
system.
1 Select “CLOCK H” (hour), then
adjust the hour.
2 Select “CLOCK M” (minute),
then adjust the minute.
3 Select “24H/12H,” then select
“24H” (hour) or “12H” (hour).
3 Finish the procedure.
To check the current clock time when the
power is turned off
EN06-11_KD-S1501[EX_EU]f.indd 7EN06-11_KD-S1501[EX_EU]f.indd 7 10/27/04 3:22:50 PM10/27/04 3:22:50 PM
8
ENGLISH
Radio operations
Listening to the radio
~
Lights up when receiving an FM stereo
broadcast with sufficient signal strength.
Selected band appears.
Ÿ Start searching for a station.
When a station is received, searching
stops.
To stop searching, press the same
button again.
To tune in to a station manually
In step Ÿ above...
1
2 Select the desired station frequencies.
When an FM stereo broadcast is hard to
receive
1
2
Lights up when monaural mode is activated.
Reception improves, but stereo effect will
be lost.
To restore the stereo effect, repeat the same
procedure. “MONO OFF” appears and the MO
indicator goes off.
EN06-11_KD-S1501[EX_EU]f.indd 8EN06-11_KD-S1501[EX_EU]f.indd 8 10/27/04 3:22:51 PM10/27/04 3:22:51 PM
9
ENGLISH
2
3
Preset number flashes for a while.
Listening to a preset station
1
2
Select the preset station (1 – 6) you
want.
To check the current clock time while
listening to an FM (non-RDS) or AM station
For FM RDS stations, see page 12.
Storing stations in memory
You can preset six stations for each band.
FM station automatic presetting
SSM (Strong-station Sequential
Memory)
1
Select the FM band (FM1 – FM3)
you want to store into.
2
3
“SSM” flashes, then disappears when
automatic presetting is over.
Local FM stations with the strongest signals are
searched and stored automatically in the FM
band.
Manual presetting
Ex.: Storing FM station of 92.5 MHz into the
preset number 4 of the FM1 band.
1
EN06-11_KD-S1501[EX_EU]f.indd 9EN06-11_KD-S1501[EX_EU]f.indd 9 10/27/04 3:22:51 PM10/27/04 3:22:51 PM
10
ENGLISH
FM RDS operations
Searching for your favorite FM RDS programme
You can tune in to a station broadcasting your
favorite programme by searching for a PTY code.
~
The last selected PTY code appears.
Ÿ Select one of your favorite
programme type.
or
Select one of the twenty-nine PTY
codes.
Ex.: When “ROCK M” is selected
! Start searching for your favorite
programme.
If there is a station broadcasting a
programme of the same PTY code as
you have selected, that station is tuned
in.
PTY codes
NEWS, AFFAIRS, INFO, SPORT,
EDUCATE, DRAMA, CULTURE,
SCIENCE, VARIED, POP M (music),
ROCK M (music), EASY M (music),
LIGHT M (music), CLASSICS, OTHER
M (music), WEATHER, FINANCE,
CHILDREN, SOCIAL, RELIGION,
PHONE IN, TRAVEL, LEISURE, JAZZ,
COUNTRY, NATION M (music), OLDIES,
FOLK M (music), DOCUMENT
EN06-11_KD-S1501[EX_EU]f.indd 10EN06-11_KD-S1501[EX_EU]f.indd 10 10/29/04 11:49:32 AM10/29/04 11:49:32 AM
11
ENGLISH
What you can do with RDS
RDS (Radio Data System) allows FM
stations to send an additional signal along
with their regular programme signals.
By receiving the RDS data, this receiver can
do the following:
Programme Type (PTY) Search (see page 10)
Standby Reception of Traffic
Announcement —TA (see the following) or
your favorite programme (PTY) (see pages
12 and 18)
Tracing the same programme automatically
—Network-Tracking Reception (see page 12)
Programme Search (see page 18)
Storing your favorite programmes
You can store six favorite programme types.
Preset programme types in the number buttons
(1 – 6):
1 Perform steps ~ and Ÿ on page 10 to
select a PTY code.
2 Select the preset number (1 – 6) you
want to store into.
Ex.: When “ROCK M” is selected
3 Repeat steps 1 and 2 to store
other PTY codes into other preset
numbers.
4 Finish the procedure.
Using the standby receptions
TA Standby Reception
TA Standby Reception allows the receiver to
switch temporarily to Traffic Announcement
(TA) from any source other than AM.
The volume changes to the preset TA volume
level (see page 18).
To activate TA Standby Reception
The TP indicator either
lights up or flashes.
If the TP indicator lights up, TA Standby
Reception is activated.
If the TP indicator flashes, TA Standby
Reception is not yet activated. (This occurs
when you are listening to an FM station
without the RDS signals required for TA
Standby Reception.)
To activate TA Standby Reception, tune in to
another station providing these signals. The
TP indicator will stop flashing and remain lit.
To deactivate the TA Standby Reception
The TP indicator goes off.
EN06-11_KD-S1501[EX_EU]f.indd 11EN06-11_KD-S1501[EX_EU]f.indd 11 10/27/04 3:22:52 PM10/27/04 3:22:52 PM
12
ENGLISH
Tracking the same programme—
Network-Tracking Reception
When driving in an area where FM reception
is not sufficient enough, this receiver
automatically tunes in to another FM RDS
station of the same network, possibly
broadcasting the same programme with stronger
signals (see the illustration below).
When shipped from the factory, Network-
Tracking Reception is activated.
To change the Network-Tracking Reception
setting, see page 18.
Programme A broadcasting on different
frequency areas (01 – 05)
To check the current clock time while
listening to an FM RDS station
PTY Standby Reception
PTY Standby Reception allows the receiver
to switch temporarily to your favorite PTY
programme from any source other than AM.
To activate and select your favorite PTY
code for PTY Standby Reception, see page
18.
The PTY indicator either lights up or flashes.
If the PTY indicator lights up, PTY Standby
Reception is activated.
If the PTY indicator flashes, PTY Standby
Reception is not yet activated.
To activate PTY Standby Reception, tune in
to another station providing these signals. The
PTY indicator will stop flashing and remain
lit.
To deactivate the PTY Standby Reception,
select “OFF” for the PTY code (see page 18).
The PTY indicator goes off.
EN12-17_KD-S1501[EX_EU]f.indd 12EN12-17_KD-S1501[EX_EU]f.indd 12 10/29/04 11:50:02 AM10/29/04 11:50:02 AM
13
ENGLISH
Disc operations
Playing a disc
All tracks will be played repeatedly until you
change the source or eject the disc.
To stop play and eject the disc
To fast-forward or reverse the track
Fast-forwards.
Reverses.
To go to the next or previous tracks
To the following
tracks.
To the beginning of the current track, then
the previous tracks.
To go to a particular track directly
To select a number from 01 – 06:
To select a number from 07 – 12:
Total playing time of
the inserted disc
Total track number
of the inserted disc
Elapsed playing
time
Current track
number
EN12-17_KD-S1501[EX_EU]f.indd 13EN12-17_KD-S1501[EX_EU]f.indd 13 10/27/04 3:23:20 PM10/27/04 3:23:20 PM
14
ENGLISH
Prohibiting disc ejection
You can lock a disc in the loading slot.
To cancel the prohibition, repeat the same
procedure.
To check the current clock time while
listening to a disc
Selecting the playback modes
You can use only one of the following playback modes at a time.
1
2 Select your desired playback mode.
Repeat play
Ex.: When “TRK RPT” is selected
Mode Plays repeatedly
TRK RPT: The current track.
RPT lights up.
RPT OFF: Cancels.
Random play
Mode Plays at random
Ex.: When “DISC RND” is selected
DISC RND: All tracks of the current disc.
• RND
lights up.
RND OFF: Cancels.
EN12-17_KD-S1501[EX_EU]f.indd 14EN12-17_KD-S1501[EX_EU]f.indd 14 10/27/04 3:23:20 PM10/27/04 3:23:20 PM
15
ENGLISH
Sound adjustments
Selecting preset sound modes (C-EQ: custom equalizer)
You can select a preset sound mode suitable to
the music genre.
~
Ÿ
Ex.: When “ROCK” is selected
Indication pattern for each sound mode:
Indication For:
Preset values
BAS
*
1
TRE
*
2
LOUD
*
3
USER (Flat sound) 00 00 OFF
ROCK Rock or
disco music
+03 +01 ON
CLASSIC Classical
music
+01 –02 OFF
POPS Light music +04 +01 OFF
HIP HOP Funk or rap
music
+02 00 ON
JAZZ Jazz music +02 +03 OFF
*
1
BAS: Bass
*
2
TRE: Treble
*
3
LOUD: Loudness
EN12-17_KD-S1501[EX_EU]f.indd 15EN12-17_KD-S1501[EX_EU]f.indd 15 10/27/04 3:23:21 PM10/27/04 3:23:21 PM
16
ENGLISH
Adjusting the sound
You can adjust the sound characteristics to your
preference.
1
Ex.: When “TRE” is selected
2
Indication pattern changes as
you adjust the level.
Indication To do: Range
BAS*
1
(bass)
Adjust the bass. –06 (min.)
to
+06 (max.)
TRE*
1
(treble)
Adjust the treble. –06 (min.)
to
+06 (max.)
FAD*
2
(fader)
Adjust the front
and rear speaker
balance.
R06 (Rear
only)
to
F06 (Front
only)
BAL
(balance)
Adjust the left
and right speaker
balance.
L06 (Left
only)
to
R06 (Right
only)
LOUD*
1
(loudness)
Boost low and
high frequencies
to produce a well-
balanced sound at
low volume level.
LOUD ON
J
LOUD OFF
VOL*
3
(volume)
Adjust the volume. 00 (min.) to
30 or 50
(max.)*
4
*
1
When you adjust the bass, treble, or
loudness, the adjustment you have made is
stored for the currently selected sound mode
(C-EQ) including “USER.”
*
2
If you are using a two-speaker system, set
the fader level to “00.”
*
3
Normally the +/– buttons work as the volume
control. So you do not have to select “VOL”
to adjust the volume level.
*
4
Depending on the amplifier gain control
setting. (See page 18 for details.)
EN12-17_KD-S1501[EX_EU]f.indd 16EN12-17_KD-S1501[EX_EU]f.indd 16 10/27/04 3:23:21 PM10/27/04 3:23:21 PM
17
ENGLISH
Indications Selectable settings, [reference page]
DEMO
Display demonstration
DEMO ON: [Initial]; Display demonstration will be activated
automatically if no operation is done for about
20 seconds, [7].
DEMO OFF: Cancels.
CLOCK H
Hour adjustment
0 – 23 (1 – 12), [7]
[Initial: 0 (0:00)]
CLOCK M
Minute adjustment
00 – 59, [7]
[Initial: 00 (0:00)]
24H/12H
24 hours or 12 hours time
display
12H O 24H, [7]
[Initial: 24H]
CLK ADJ
Automatic clock setting
AUTO: [Initial]; The built-in clock is automatically adjusted
using the CT (clock time) data in the RDS signal.
OFF: Cancels.
General settings — PSM
Basic procedure
You can change PSM (Preferred Setting Mode)
items listed on the table that follows.
1
2
Select a PSM item.
Ex.: When you select “AMP GAIN”
3 Adjust the PSM item selected.
4 Repeat steps 2 and 3 to adjust the
other PSM items if necessary.
5 Finish the procedure.
To be continued....
EN12-17_KD-S1501[EX_EU]f.indd 17EN12-17_KD-S1501[EX_EU]f.indd 17 10/27/04 3:23:22 PM10/27/04 3:23:22 PM
18
ENGLISH
Indications Selectable settings, [reference page]
AF-REG
Alternative frequency/
regionalization reception
When the received signals from the current station become weak....
AF: [Initial]; Switches to another station (the programme
may differ from the one currently received), [12].
The AF indicator lights up.
AF REG: Switches to another station broadcasting the same
programme.
The AF and REG indicators light up.
OFF: Cancels.
PTY-STBY
PTY standby
Activates PTY Standby Reception with one of the 29 PTY codes,
[12].
OFF [Initial]
=
PTY codes, [10]
=
(back to the beginning)
TA VOL
Traffic announcement
volume
[Initial: VOL 20]; VOL 00 – VOL 30 or 50*
1
, [11]
P-SEARCH
Programme search
ON: Using the AF data, the receiver tunes in to another
frequency broadcasting the same programme as the
original preset RDS station is if the preset station
signals are not sufficient.
OFF: [Initial]; Cancels.
ILL SW*
2
Illumination switch
You can select the button illumination according to your
preference.
RED O GREEN
[Initial: RED]
TEL*
2
Telephone muting
MUTING 1/MUTING 2: Select either one which mutes the
sounds while using the cellular phone.
OFF: [Initial]; Cancels.
AMP GAIN
Amplifier gain control
You can change the maximum volume level of this receiver.
LOW PWR: VOL 00 – VOL 30 (Select this if the maximum
power of the speaker is less than 45 W to prevent
them from damaging the speaker.)
HIGH PWR: [Initial]; VOL 00 – VOL 50
*
1
Depends on the amplifier gain control.
*
2
Only for KD-S1501.
EN18-23_KD-S1501[EX_EU]f.indd 18EN18-23_KD-S1501[EX_EU]f.indd 18 10/29/04 3:49:57 PM10/29/04 3:49:57 PM
19
ENGLISH
When detaching or attaching the control panel,
be careful not to damage the connectors on
the back of the control panel and on the panel
holder.
Detaching the control panel
Before detaching the control panel, be sure to
turn off the power.
Attaching the control panel
Detaching the control panel
EN18-23_KD-S1501[EX_EU]f.indd 19EN18-23_KD-S1501[EX_EU]f.indd 19 10/27/04 3:23:52 PM10/27/04 3:23:52 PM
20
ENGLISH
Maintenance
How to clean the connectors
Frequent detachment will deteriorate the
connectors.
To minimize this possibility, periodically wipe
the connectors with a cotton swab or cloth
moistened with alcohol, being careful not to
damage the connectors.
Connector
Moisture condensation
Moisture may condense on the lens inside the
CD player in the following cases:
After starting the heater in the car.
If it becomes very humid inside the car.
Should this occur, the CD player may
malfunction. In this case, eject the disc and
leave the receiver turned on for a few hours
until the moisture evaporates.
How to handle discs
When removing a disc from
its case, press down the center
holder of the case and lift the
disc out, holding it by the
edges.
Always hold the disc by the edges. Do not
touch its recording surface.
When storing a disc into its case, gently insert
the disc around the center holder (with the
printed surface facing up).
Make sure to store discs into the cases after
use.
To keep discs clean
A dirty disc may not play correctly.
If a disc does become dirty, wipe
it with a soft cloth in a straight line
from center to edge.
Do not use any solvent (for
example, conventional record cleaner, spray,
thinner, benzine, etc.) to clean discs.
To play new discs
New discs may have some rough
spots around the inner and outer
edges. If such a disc is used, this
receiver may reject the disc.
To remove these rough spots, rub the edges
with a pencil or ball-point pen, etc.
Center holder
Warped
disc
Sticker
Sticker
residue
Disc
Stick-on
label
Do not use the following discs:
EN18-23_KD-S1501[EX_EU]f.indd 20EN18-23_KD-S1501[EX_EU]f.indd 20 10/27/04 3:23:52 PM10/27/04 3:23:52 PM
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46

JVC KD-G152 Le manuel du propriétaire

Catégorie
Récepteurs multimédia de voiture
Taper
Le manuel du propriétaire

dans d''autres langues