JVC KD-AR370 Manuel utilisateur

ENGLISH

ESPAÑOL

FRANÇAIS

CD RECEIVER KD-AR370/KD-G320

RECEPTOR CON CD KD-AR370/KD-G320

RECEPTEUR CD KD-AR370/KD-G320

For canceling the display demonstration, see page 7.

Para cancelar la demostración en pantalla, consulte la página 7.

Pour annuler la démonstration des affichages, référez-vous à la page 7.

For installation and connections, refer to the separate manual.

Para la instalación y las conexiones, refiérase al manual separado.

Pour l’installation et les raccordements, se référer au manuel séparé.

INSTRUCTIONS

MANUAL DE INSTRUCCIONES

MANUEL D’INSTRUCTIONS

For customer Use:

Enter below the Model

No. and Serial No. which

are located on the top or

bottom of the cabinet.

Retain this information

for future reference.

Model No.

Serial No.

GET0349-001A

[J]

Cover_KD-AR370_320[J]2.indd 2Cover_KD-AR370_320[J]2.indd 2 10/21/05 4:47:02 PM10/21/05 4:47:02 PM

2

ENGLISH

Thank you for purchasing a JVC product.

Please read all instructions carefully

before operation, to ensure your complete

understanding and to obtain the best possible

performance from the unit.

How to reset your unit

• Your preset adjustments will also be erased.

• If a disc is loaded, it will eject. Be careful not to

drop the disc.

How to forcibly eject a disc

• If this does not work, reset your unit.

• Be careful not to drop the disc when it ejects.

How to use the MODE button

If you press MODE, the unit goes into functions

mode, then the number buttons and 5/∞

buttons work as different function buttons.

Ex.: When number button 2 works as

MO (monaural) button.

To use these buttons for their original

functions again after pressing MODE, wait for

5 seconds without pressing any of these buttons

until the functions mode is cleared or press

MODE again.

INFORMATION (For U.S.A.)

This equipment has been tested and found

to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide

reasonable protection against harmful

interference in a residential installation.

This equipment generates, uses, and can

radiate radio frequency energy and, if not

installed and used in accordance with the

instructions, may cause harmful interference

to radio communications. However, there

is no guarantee that interference will not

occur in a particular installation. If this

equipment does cause harmful interference

to radio or television reception, which can

be determined by turning the equipment

off and on, the user is encouraged to try to

correct the interference by one or more of

the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the

equipment and receiver.

– Connect the equipment into an outlet on

a circuit different from that to which the

receiver is connected.

– Consult the dealer or an experienced

radio/TV technician for help.

Caution:

Changes or modifications not approved

by JVC could void the user’s authority to

operate the equipment.

IMPORTANT FOR LASER PRODUCTS

1. CLASS 1 LASER PRODUCT

2. CAUTION: Do not open the top cover.

There are no user serviceable parts inside

the unit; leave all servicing to qualified

service personnel.

3. CAUTION: Visible and invisible laser

radiation when open and interlock failed or

defeated. Avoid direct exposure to beam.

Time countdown indicator

EN02-05KD-AR370_320[J]f.indd 2EN02-05KD-AR370_320[J]f.indd 2 11/15/05 5:23:02 PM11/15/05 5:23:02 PM

ENGLISH

3

How to read this manual

• Button operations are mainly explained with

the illustrations in the table below.

• Some related tips and notes are explained in

“More about this unit” (see pages 20 – 22).

Press briefly.

Press repeatedly.

Press either

one.

Press and hold until your

desired response begins.

Press and hold both

buttons at the same time.

The following marks are used to indicate...

: Built-in CD player operations.

: External CD changer operations.

: Indicator displayed for the

corresponding operation.

How to detach/attach the control

panel

CONTENTS

Control panel — KD-AR370 and KD-G320 ....... 4

Remote controller —

RM-RK50 .............. 5

Getting started ................................. 6

Basic operations .................................................... 6

Radio operations .............................. 7

Disc operations ................................. 8

Playing a disc in the unit ...................................... 8

Playing discs in the CD changer ............................ 9

Sound adjustments ........................... 11

General settings — PSM ................... 12

Satellite radio operations .................. 15

iPod®/D. player operations ................ 18

Other external component operations

... 20

More about this unit ......................... 20

Maintenance .................................... 23

Troubleshooting ............................... 24

Specifications ................................... 27

Warning:

If you need to operate the unit while driving,

be sure to look ahead carefully or you may be

involved in a traffic accident.

For safety...

• Do not raise the volume level too much, as

this will block outside sounds, making driving

dangerous.

• Stop the car before performing any

complicated operations.

Temperature inside the car...

If you have parked the car for a long time in hot

or cold weather, wait until the temperature in

the car becomes normal before operating the

unit.

Detaching...

Attaching...

EN02-05KD-AR370_320[J]f.indd 3EN02-05KD-AR370_320[J]f.indd 3 10/31/05 2:18:57 PM10/31/05 2:18:57 PM

4

ENGLISH

Control panel — KD-G612/KD-G611/KD-G511

1 4 /¢ buttons

2

(standby/on attenuator) button

3 5 (up) / ∞ (down) buttons

4 Loading slot

5 Display window

6 0 (eject) button

7 EQ (equalizer) button

8 Remote sensor

DO NOT expose the remote sensor to strong

light (direct sunlight or artificial lighting).

9 SRC (source) button

p BAND button

q Control dial

w SEL (select) button

e MO (monaural) button

r SSM (Strong-station Sequential Memory)

button

t Number buttons

y RPT (repeat) button

u RND (random) button

i MODE button

o DISP (display) button

;

(control panel release) button

Display window

a Disc information indicators—TAG (ID3

Tag),

(folder), (track/file)

s Disc type indicators—WMA, MP3

d Playback source indicators—

CH: Lights up only when CD-CH is

selected as the playback source.

DISC: Lights up for the built-in CD player.

f Playback mode / item indicators—

RND (random),

(disc), (folder),

RPT (repeat)

g LOUD (loudness) indicator

h EQ (equalizer) indicator

j Sound mode (C-EQ: custom equalizer)

indicators—JAZZ, CLASSIC, HIP HOP,

POPS, ROCK, USER

k Tr (track) indicator

l Source display / Volume level indicator

/ Main display

z Tuner reception indicators—ST (stereo),

MO (monaural)

Parts identification

Display window

Control panel — KD-AR370 and KD-G320

EN02-05KD-AR370_320[J]f.indd 4EN02-05KD-AR370_320[J]f.indd 4 10/28/05 5:32:19 PM10/28/05 5:32:19 PM

ENGLISH

5

Remote controller — RM-RK50

Installing the lithium coin battery

(CR2025)

Aim the remote controller directly at the

remote sensor on the unit. Make sure there is

no obstacle in between.

Warning:

• Do not install any battery other than

CR2025 or its equivalent; otherwise, it may

explode.

• Store the battery in a place where children

cannot reach to avoid risk of accident.

• To prevent the battery from over-heating,

cracking, or starting a fire:

– Do not recharge, short, disassemble, heat

the battery, or dispose of it in a fire.

– Do not leave the battery with other

metallic materials.

– Do not poke the battery with tweezers or

similar tools.

– Wrap the battery with tape and insulate

when throwing away or saving it.

Caution:

Main elements and features

1 (standby/on/attenuator) button

• Turns the power on if pressed briefly or

attenuates the sound when the power is

on.

• Turns the power off if pressed and held.

2 5 U (up) / D (down) ∞ buttons

• Changes the FM/AM bands with 5 U.

• Changes the preset stations with D ∞.

• Changes the folder of the MP3/WMA

discs.

• While playing an MP3 disc on an

MP3-compatible CD changer:

– Changes the disc if pressed briefly.

– Changes the folder if pressed and held.

• While listening to the satellite (SIRIUS or

XM) radio:

– Changes the categories.

• While listening to an Apple iPod

®

or a

JVC D. player:

– Pauses/stops or resumes playback with

D ∞.

– Enters the main menu with 5 U.

(Now 5 U/D ∞/2 R/F 3 work as the

menu selecting buttons.)*

3 VOL – / VOL + buttons

• Adjusts the volume level.

* 5 U : Returns to the previous menu.

D ∞ : Confirms the selection.

To be continued...

EN02-05KD-AR370_320[J]f.indd 5EN02-05KD-AR370_320[J]f.indd 5 11/15/05 5:23:08 PM11/15/05 5:23:08 PM

6

ENGLISH

!

• For FM/AM tuner

• For SIRIUS radio

• For XM radio

⁄ Adjust the volume.

@ Adjust the sound as you want. (See

pages 11 and 12.)

Caution on volume setting:

Discs produce very little noise compared

with other sources. Lower the volume

before playing a disc to avoid damaging

the speakers by the sudden increase of the

output level.

To drop the volume in a

moment (ATT)

To restore the sound, press

it again.

To turn off the power

Volume level indicator

Volume level appears.

4 SOUND button

• Selects the sound mode (C-EQ: custom

equalizer).

5 SOURCE button

• Selects the source.

6 2 R (reverse) / F (forward) 3 buttons

• Searches for stations if pressed briefly.

• Fast-forwards or reverses the track if

pressed and held.

• Changes the tracks if pressed briefly.

• While listening to the satellite radio:

– Changes the channels if pressed briefly.

– Changes the channels rapidly if pressed

and held.

• While listening to an iPod or a D. player

(in menu selecting mode):

– Selects an item if pressed briefly. (Then,

press D ∞ to confirm the selection.)

– Skips 10 items at a time if pressed and

held.

Getting started

Basic operations

~ Turn on the power.

Ÿ

* You cannot select these sources if they

are not ready or not connected.

EN06-11KD-AR370_320[J]f.indd 6EN06-11KD-AR370_320[J]f.indd 6 10/28/05 5:34:24 PM10/28/05 5:34:24 PM

7

ENGLISH

Basic settings

• See also “General settings — PSM” on pages

12 – 14.

1

2

1 Canceling the display

demonstrations

Select “DEMO,” then “DEMO OFF.”

2 Setting the clock

Select “CLOCK H” (hour), then adjust

the hour.

Select “CLOCK M” (minute), then

adjust the minute.

3 Finish the procedure.

To check the current clock

time when the power is

turned off

Radio operations

~

Ÿ

Lights up when receiving an FM stereo

broadcast with sufficient signal strength.

Selected band appears.

! Start searching for a station.

When a station is received, searching

stops.

To stop searching, press the same button

again.

To tune in to a station manually

In step ! above...

1

2 Select a desired station frequency.

When an FM stereo broadcast is hard to

receive

Reception improves, but stereo effect will be

lost.

To restore the stereo effect, repeat the same

procedure. “MONO OFF” appears and the MO

indicator goes off.

Lights up when monaural mode is activated.

EN06-11KD-AR370_320[J]2.indd 7EN06-11KD-AR370_320[J]2.indd 7 10/21/05 4:46:42 PM10/21/05 4:46:42 PM

8

ENGLISH

Listening to a preset station

1

2 Select the preset station (1 – 6) you

want.

or

To check the other information while

listening to an FM or AM station

Disc operations

Playing a disc in the unit

All tracks will be played repeatedly until you

change the source or eject the disc.

To stop play and eject the

disc

Storing stations in memory

You can preset six stations for each band.

FM station automatic presetting —

SSM (Strong-station Sequential

Memory)

1 Select the FM band (FM1 – FM3) you

want to store into.

2

3

“SSM” flashes, then disappears when

automatic presetting is over.

Local FM stations with the strongest signals are

searched and stored automatically in the FM

band.

Manual presetting

Ex.: Storing FM station of 92.5 MHz into preset

number 4 of the FM1 band.

1

2

3

Clock Ô Frequency

Preset number flashes for a while.

EN06-11KD-AR370_320[J]2.indd 8EN06-11KD-AR370_320[J]2.indd 8 10/21/05 4:46:43 PM10/21/05 4:46:43 PM

9

ENGLISH

Playing discs in the CD changer

All discs in the magazine will be played

repeatedly until you change the source.

• Ejecting the magazine will also stop playing.

~

* If you have changed the external input

setting to “EXT IN” (see page 14), you

cannot select the CD changer.

Ÿ Select a disc.

For disc number from 01 – 06:

For disc number from 07 – 12:

About MP3 and WMA discs

MP3 and WMA “tracks” (words “file” and

“track” are used interchangeably) are recorded

in “folders.”

About the CD changer

It is recommended to use a JVC

MP3-compatible CD changer with your unit.

• You can also connect other CH-X series CD

changers (except CH-X99 and CH-X100).

These units are not compatible with MP3

discs.

• You cannot play any WMA disc in the CD

changer.

• You cannot use the KD-MK series CD

changers with this unit.

• Disc text information recorded in the CD

Text can be displayed when a JVC CD Text

compatible CD changer is connected.

• For connection, see Installation/Connection

Manual (separate volume).

To fast-forward or reverse the track

To go to the next or previous tracks

To go to the next or previous folders (only for

MP3 or WMA discs)

For MP3 discs:

For WMA discs:

To locate a particular track (for CD) or folder

(for MP3 or WMA discs) directly

To select a number from 01 – 06:

To select a number from 07 – 12:

• To use direct folder access on MP3/WMA

discs, it is required that folders are assigned

with 2-digit numbers at the beginning of their

folder names—01, 02, 03, and so on.

To select a

particular track in a

folder (for MP3 or

WMA discs):

EN06-11KD-AR370_320[J]2.indd 9EN06-11KD-AR370_320[J]2.indd 9 10/21/05 4:46:44 PM10/21/05 4:46:44 PM

10

ENGLISH

Changing the display information

While playing an audio CD or a CD Text

While playing an MP3 or a WMA

*

2

disc

• When “TAG DISP” is set to

“TAG ON” (see page 14)

• When “TAG DISP” is set to

“TAG OFF”

: Clock with the current track number

: Elapsed playing time with the

current track number

*

1

If the current disc is an audio CD,

“NO NAME” appears.

*

2

Only for the built-in CD player.

*

3

If an MP3/WMA file does not have Tag

information, folder name and file name

appear. In this case, the TAG indicator will

not light up.

Other main functions

Skipping tracks quickly during play

Only possible on JVC

MP3-compatible CD changer

• For MP3 or WMA discs, you can skip tracks

within the same folder.

Ex.: To select track 32 while playing a track

whose number is a single digit (1 to 9)

1

2

Each time you press the button, you can

skip 10 tracks.

• After the last track, the first track will be

selected and vice versa.

3

Prohibiting disc ejection

You can lock a disc in the loading slot.

To cancel the prohibition, repeat the same

procedure.

EN06-11KD-AR370_320[J]f.indd 10EN06-11KD-AR370_320[J]f.indd 10 11/15/05 5:23:38 PM11/15/05 5:23:38 PM

11

ENGLISH

Selecting the playback modes

You can use only one of the following playback

modes at a time.

1

2 Select your desired playback mode.

7 Repeat play

Mode Plays repeatedly

TRK RPT : The current track.

FLDR RPT*

1

: All tracks of the current

folder.

DISC RPT*

2

: All tracks of the current

disc.

RPT OFF : Cancels.

7

Random play

Mode Plays at random

FLDR RND*

1

: All tracks of the current

folder, then tracks of the

next folder and so on.

DISC RND : All tracks of the current

disc.

MAG RND*

2

: All tracks of the inserted

discs.

RND OFF : Cancels.

*

1

Only while playing an MP3 or a WMA

disc.

*

2

Only while playing discs in the CD

changer.

To be continued...

Sound adjustments

You can select a preset sound mode suitable to

the music genre (C-EQ: custom equalizer).

Indication (For)

BAS TRE LOUD

(bass) (treble) (loudness)

USER

(Flat sound)

00 00 OFF

ROCK

(Rock or disco music)

+03 +01 ON

CLASSIC

(Classical music)

+01 –02 OFF

POPS

(Light music)

+04 +01 OFF

HIP HOP

(Funk or rap music)

+02 00 ON

JAZZ

(Jazz music)

+02 +03 OFF

Adjusting the sound

You can adjust the sound characteristics to your

preference.

1

Preset values

Ex.: When “ROCK” is selected

EN06-11KD-AR370_320[J]f.indd 11EN06-11KD-AR370_320[J]f.indd 11 11/23/05 11:53:27 AM11/23/05 11:53:27 AM

12

ENGLISH

General settings — PSM

You can change PSM (Preferred Setting Mode)

items (except “SID”) listed in the table that

follows.

1

2 Select a PSM item.

3 Adjust the PSM item selected.

4 Repeat steps 2 and 3 to adjust other

PSM items if necessary.

5 Finish the procedure.

2

Indication [Range]

BAS*

1

(bass)

Adjust the bass. [–06 to +06]

TRE*

1

(treble)

Adjust the treble. [–06 to +06]

FAD*

2

(fader)

Adjust the front and rear speaker balance.

[R06 to F06]

BAL*

3

(balance)

Adjust the left and right speaker balance.

[L06 to R06]

LOUD*

1

(loudness)

Boost low and high frequencies to produce

a well-balanced sound at low volume level.

[LOUD ON or LOUD OFF]

SUB.W*

4

(subwoofer)

Adjust the subwoofer output level. [00 to 08]

VOL (volume)

Adjust the volume. [00 to 30 or 50*

5

]

*

1

When you adjust the bass, treble, or loudness,

the adjustment you have made is stored for

the currently selected sound mode (C-EQ)

including “USER.”

*

2

If you are using a two-speaker system, set the

fader level to “00.”

*

3

This adjustment cannot affect the subwoofer

output.

*

4

This takes effect only when a subwoofer is

connected.

Displayed only when “L/O MODE” is set to

“WOOFER” (see page 14).

*

5

Depending on the amplifier gain control

setting. (See page 14 for details.)

Ex.: When “DIMMER” is selected

EN12-17KD-AR370_320[J]f.indd 12EN12-17KD-AR370_320[J]f.indd 12 11/23/05 11:52:50 AM11/23/05 11:52:50 AM

ENGLISH

13

Indications Selectable settings, [reference page]

DEMO

Display

demonstration

DEMO ON : [Initial]; Display demonstration will be activated

automatically if no operation is done for about 20 seconds,

[7].

DEMO OFF : Cancels.

CLOCK H

Hour adjustment

1 – 12, [7]

[Initial: 1 (1:00)]

CLOCK M

Minute adjustment

00 – 59, [7]

[Initial: 00 (1:00)]

CLK ADJ*

1

Clock adjustment

AUTO : [Initial]; The built-in clock is automatically adjusted using

the clock data provided via the satellite radio channel.

OFF : Cancels.

T-ZONE*

1

, *

2

Time zone

Select your residential area from one of the following time zones for clock

adjustment.

EASTERN [Initial] “ ATLANTIC “ NEWFOUND “ ALASKA “

PACIFIC “ MOUNTAIN “ CENTRAL “ (back to the beginning)

DST*

1

, *

2

Daylight savings

time

Activate this if your residential area is subject to DST.

ON : [Initial]; Activates daylight savings time.

OFF : Cancels.

SID*

3

SIRIUS ID

The 12-digit SIRIUS identification number scrolls on the display 5 seconds

after “SID” is selected, [15].

• Press SEL to resume the previous display.

DIMMER

Dimmer

ON : Dims the display illumination of this unit.

OFF : [Initial]; Cancels.

TEL*

4

Telephone muting

MUTING 1/MUTING 2: Select either one which mutes the sounds while

using a cellular phone.

OFF : [Initial]; Cancels.

SCROLL*

5

Scroll

ONCE : [Initial]; Scrolls the disc information once.

AUTO : Repeats scrolling (5-second intervals in between).

OFF : Cancels.

• Pressing DISP for more than one second can scroll the display regardless

of the setting.

*

1

Displayed only when SIRIUS Satellite radio or XM Satellite radio is connected.

*

2

Displayed only when “CLK ADJ” is set to “AUTO.”

*

3

Displayed only when SIRIUS Satellite radio is connected.

*

4

Only for KD-AR370.

*

5

Some characters or symbols will not be shown correctly (or will be blanked) on the display.

To be continued...

EN12-17KD-AR370_320[J]f.indd 13EN12-17KD-AR370_320[J]f.indd 13 11/7/05 1:02:14 PM11/7/05 1:02:14 PM

14

ENGLISH

Indications Selectable settings, [reference page]

WOOFER*

1

Subwoofer cutoff

frequency

LOW : Frequencies lower than 90 Hz are sent to the subwoofer.

MID : [Initial]; Frequencies lower than 135 Hz are sent to the

subwoofer.

HIGH : Frequencies lower than 180 Hz are sent to the subwoofer.

EXT IN*

2

External input

CHANGER : [Initial]; To use a JVC CD changer, [9], a JVC compatible

satellite (SIRIUS/XM) tuner, [15], an Apple iPod or a JVC

D. player, [18].

EXT IN : To use any other external component than the above,

[20].

L/O MODE

Line output mode

When connecting amplifiers and/or subwoofer, set this correctly.

REAR : [Initial]; Select if the both LINE OUT terminals are

used for connecting the speakers through the external

amplifiers.

WOOFER : Select if the FRONT LINE OUT terminals are used for

connecting a subwoofer through an external amplifier.

TAG DISP

Tag display

TAG ON : [Initial]; Shows the Tag information while playing MP3/

WMA tracks, [10].

TAG OFF : Cancels.

AMP GAIN

Amplifier gain

control

You can change the maximum volume level of this unit.

LOW PWR : VOL 00 – VOL 30 (Select this if the maximum power of

the speaker is less than 50 W to prevent them from being

damaged.)

HIGH PWR : [Initial]; VOL 00 – VOL 50

AREA

Tuner channel

interval

AREA US : [Initial]; When using in North/Central/South America.

AM/FM intervals are set to 10 kHz/200 kHz.

AREA SA : When using in South American countries where FM

interval is 100 kHz. AM interval is set to 10 kHz.

AREA EU : When using in any other areas. AM/FM intervals are set

to 9 kHz/50 kHz (100 kHz during auto search).

*

1

Displayed only when “L/O MODE” is set to “WOOFER.”

*

2

Displayed only when one of the following sources is selected—FM, AM, or DISC.

EN12-17KD-AR370_320[J]f.indd 14EN12-17KD-AR370_320[J]f.indd 14 11/21/05 10:28:13 AM11/21/05 10:28:13 AM

ENGLISH

15

Satellite radio operations

This unit is satellite (SAT) Radio Ready—

compatible with both SIRIUS Satellite radio and

XM Satellite radio.

Before operating your satellite radio:

• For connection, see Installation/Connection

Manual (separate volume).

• Refer also to the Instructions supplied with

your SIRIUS Satellite radio or XM Satellite

radio.

• “SIRIUS” and the SIRIUS dog logo are

registered trademarks of SIRIUS Satellite Radio

Inc.

• XM and its corresponding logos are registered

trademarks of XM Satellite Radio Inc.

• “SAT Radio,” the SAT Radio logo and all

related marks are trademarks of SIRIUS

Satellite Radio Inc., and XM Satellite Radio,

Inc.

Listening to the satellite radio

Connect either one of the following (separately

purchased) to the CD changer jack on the rear

of this unit.

• JVC SIRIUS radio DLP—Down Link

Processor, for listening to the SIRIUS Satellite

radio.

• XMDirect

TM

Universal Tuner Box using a

JVC Smart Digital Adapter—XMDJVC100

(not supplied), for listening to the XM

Satellite radio.

GCI (Global Control Information) update:

• If channels are updated after subscription,

updating starts automatically.

“UPDATING” flashes and no sound can be

heard.

• Update takes a few minutes to complete.

• During update, you cannot operate your

satellite radio.

To be continued...

Activate your SIRIUS subscription after

connection:

1

2

JVC DLP starts updating all the SIRIUS

channels.

Once completed, JVC DLP tunes in to the

preset channel, CH184.

3

Check your SIRIUS ID, see page 13.

4 Contact SIRIUS on the internet at

<http://activate.siriusradio.com/> to

activate your subscription, or you can

call SIRIUS toll-free at 1-888-539-

SIRIUS (7474).

“SUB UPDT PRESS ANY KEY” scrolls

on the display once subscription has been

completed.

Activate your XM subscription after

connection:

• Only Channel 0, 1, and 247 are available

before activation.

1

2

XMDirect

TM

Universal Tuner Box starts

updating all the XM channels. “Channel 1”

is tuned in automatically.

3 Check your XM Satellite radio

ID labelled on the casing of the

XMDirect

TM

Universal Tuner Box, or

tune into “Channel 0” (see page 17).

EN12-17KD-AR370_320[J]2.indd 15EN12-17KD-AR370_320[J]2.indd 15 10/21/05 4:45:52 PM10/21/05 4:45:52 PM

16

ENGLISH

Listening to the XM Satellite radio

1

2

3 Select a channel for listening.

Holding the button changes the channels

rapidly.

Searching for category/channel

You can search for programs by category

(Category Search) or channel number (Channel

Search).

• In Category Search, you can tune in to the

channels of the selected category. Category

Search begins from the currently selected

channel. The selected channel number flashes

on the display.

• In Channel Search, you can tune in to

all channels (including non-categorised

channels).

1 Select a category (Category Search).

• For Channel Search, skip

this step.

4

Contact XM Satellite radio on

the internet at <http://xmradio.

com/activation/> to activate your

subscription, or you can call 1-800-

XM-RADIO (1-800-967-2346).

Once completed, the unit tunes in to one

of the available channels (Channel 4 or

higher).

Listening to the SIRIUS Satellite radio

1

2

3 Select a category.

You can tune in to all the channels of every

category by selecting “ALL.”

Selecting a particular category (SPORTS,

ENTERTAINMENT, etc.) allows you to

enjoy only the channels from the selected

category.

4 Select a channel for listening.

Holding the button changes the channels

rapidly.

• When changing the category or channel,

invalid and unsubscribed channels are

skipped.

EN12-17KD-AR370_320[J]2.indd 16EN12-17KD-AR370_320[J]2.indd 16 10/21/05 4:45:54 PM10/21/05 4:45:54 PM

ENGLISH

17

Storing channels in memory

You can preset six channels for each band.

Ex.: Storing a channel into preset number 4.

1 Tune in to a channel you want.

2

Listening to a preset channel

1 Select either SIRIUS Satellite radio or

XM Satellite radio.

2

3 Select the preset channel (1 – 6) you

want.

To change the display information while

listening to a channel

Clock = Category name = Channel name =

Artist name = Composer name* = Song/program

name/title = (back to the beginning)

* Only for SIRIUS Satellite radio.

2 Select a channel for listening.

If no operation is done for about

15 seconds, Category Search is canceled.

In Channel Search, channel name and

channel number appear on the display

during search.

• While searching, invalid and unsubscribed

channels are skipped.

Checking the XM Satellite radio ID

While selecting “XM1,” “XM2,” or

“XM3,” select “Channel 0.”

The display alternately shows “RADIO ID” and

the 8-digit (alphanumeric) ID number.

To cancel the ID number display, select any

channel other than “Channel 0.”

Ex.: When you select “COUNTRY” for Category Search

Current channel number

Preset number flashes for a while.

EN12-17KD-AR370_320[J]2.indd 17EN12-17KD-AR370_320[J]2.indd 17 10/21/05 4:45:55 PM10/21/05 4:45:55 PM

18

ENGLISH

⁄ Adjust the sound as you want. (See

pages 11 and 12.)

• Make sure the equalizer on the iPod or

D. player is deactivated.

To pause*

1

or

stop*

2

playback

To resume

playback, press it

again.

To fast-forward or

reverse the track

To go to the next

or previous tracks

*

1

For iPod

*

2

For D. player

Selecting a track from the menu

1 Enter the main menu.

Now the 5/∞/4

/¢ buttons

work as the menu selecting buttons*

3

.

2 Select the desired menu.

For iPod:

PLAYLIST Ô ARTISTS Ô ALBUMS Ô SONGS

Ô GENRES Ô COMPOSER Ô (back to the

beginning)

For D. player:

PLAYLIST Ô ARTIST Ô ALBUM Ô GENRE

Ô TRACK Ô (back to the beginning)

iPod®/D. player operations

This unit is ready for operating an Apple iPod

or a JVC D. player from the control panel.

Before operating your iPod or D. player:

Connect either one of the following (separately

purchased) to the CD changer jack on the rear

of this unit.

• Interface adapter for iPod

®

—KS-PD100 for

controlling an iPod.

• D. player interface adapter—KS-PD500 for

controlling a D. player.

• For connection, see Installation/Connection

Manual (separate volume).

• For details, refer also to the manual supplied

with the interface adapter.

Caution:

Make sure to turn off this unit or turn off the

vehicle’s ignition switch before connecting

or disconnecting the iPod or D. player.

Preparations:

Make sure “CHANGER” is selected for the

external input setting, see page 14.

~

Ÿ

Playback starts automatically from

where it has been paused*

1

or stopped*

2

previously.

! Adjust the volume.

EN18-23KD-AR370_320[J]f.indd 18EN18-23KD-AR370_320[J]f.indd 18 11/21/05 10:29:18 AM11/21/05 10:29:18 AM

ENGLISH

19

7 Random play

ALBM RND*

4

Functions the same as “Shuffle Albums” of

the iPod.

SONG RND/RND ON

Functions the same as “Shuffle Songs” of the

iPod or “Random Play On” of the D. player.

RND OFF

Cancels.

*

4

For iPod: Only if you select “ALL” in

“ALBUMS” of the main “MENU.”

To check other information while listening to

an iPod or a D. player

3 Confirm the selection.

To move back to the previous

menu, press 5.

• If a track is selected, playback starts

automatically.

• If the selected item has another layer, you

will enter the layer. Repeat steps 2 and 3

until the desired track is played.

• Holding 4

/¢ can skip 10

items at a time.

*

3

The menu selecting mode will be canceled:

–

If no operations are done for about

5 seconds.

–

When you confirm the selection of a track.

Selecting the playback modes

1

2

Select your desired playback mode.

7 Repeat play

ONE RPT

Functions the same as “Repeat One” of

the iPod or “Repeat Mode One” for the

D. player.

ALL RPT

Functions the same as “Repeat All” of the

iPod or “Repeat Mode All” for the D. player.

RPT OFF

Cancels.

EN18-23KD-AR370_320[J]f.indd 19EN18-23KD-AR370_320[J]f.indd 19 11/25/05 12:02:25 PM11/25/05 12:02:25 PM

20

ENGLISH

Other external component

operations

You can connect an external component to

the CD changer jack on the rear using the Line

Input Adapter—KS-U57 (not supplied) or AUX

Input Adapter—KS-U58 (not supplied).

• For connection, see Installation/Connection

Manual (separate volume).

For listening to the satellite radio, iPod, or

D. player, refer to pages 15 – 19.

~

If “EXT IN” does not appear, see page 14

and select the external input (“EXT IN”).

Ÿ Turn on the connected component

and start playing the source.

! Adjust the volume.

⁄ Adjust the sound as you want. (See

pages 11 and 12.)

To check the other information while

listening to an external component

Clock Ô EXT IN

More about this unit

Basic operations

Turning on the power

• By pressing SRC on the unit, you can also

turn on the power. If the source is ready,

playback also starts.

Turning off the power

• If you turn off the power while listening to a

disc, disc play will start from where playback

has been stopped previously, next time you

turn on the power.

Tuner operations

Storing stations in memory

• During SSM search...

– All previously stored stations are erased and

stations are stored newly.

– Received stations are preset in No. 1 (lowest

frequency) to No. 6 (highest frequency).

– When SSM is over, the station stored in

No. 1 will be automatically tuned in.

• When storing a station manually, the

previously preset station is erased when a new

station is stored in the same preset number.

Disc operations

Caution for DualDisc playback

• The Non-DVD side of a “DualDisc” does

not comply with the “Compact Disc Digital

Audio” standard. Therefore, the use of Non-

DVD side of a DualDisc on this product may

not be recommended.

General

• This unit has been designed to reproduce

CDs/CD Texts, and CD-Rs (Recordable)/

CD-RWs (Rewritable) in audio CD (CD-DA),

MP3 and WMA formats.

• When a disc had been loaded, selecting

“DISC” for the playback source starts disc

play.

EN18-23KD-AR370_320[J]f.indd 20EN18-23KD-AR370_320[J]f.indd 20 11/24/05 4:28:16 PM11/24/05 4:28:16 PM

La page charge ...

JVC KD-AR370 Manuel utilisateur

Ce manuel convient également à

JVC KD-AR370 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents