Pioneer PDP 436PE Le manuel du propriétaire

PLASMA DISPLAY SYSTEM

SYSTEME D’ÉCRAN PLASMA

PLASMA DISPLAY-SYSTEM

PDP-506FDE

PDP-436FDE

Operating Instructions

Mode d’emploi

Bedienungsanleitung

Discover the benefits of registering your product online at

www.pioneer.co.uk (or www.pioneer-eur.com).

Découvrez les nombreux avantages offerts en enregistrant votre produit

en ligne maintenant sur www.pioneer.fr (ou www.pioneer-eur.com).

Bitte nutzen Sie die Möglichkeit zur Registrierung Ihres Produktes unter

www.pioneer.de (oder www.pioneer-eur.com)

This equipment complies with the requirements of Directives 89/336/EEC and 73/23/EEC as amended by 93/68/

EEC.

Dieses Gerät entspricht den Anforderungen der EG-Richtlinien 89/336/EWG und 73/23/EWG mit Änderung 93/

68/EWG.

Ce matériel répond aux exigences contenues dans les directives 89/336/CEE et 73/23/CEE modifiées par la

directive 93/68/CEE.

Dit apparaat voldoet aan de eisen van de richtlijnen 89/336/EEG en 73/23/EEG, gewijzigd door 93/68/EEG.

Dette udstyr overholder kravene i direktiv nr. 89/336/EEC og 73/23/EEC med tillæg nr. 93/68/EEC.

Quest’ apparecchio è conforme ai requisiti delle direttive 89/336/EEC e 73/23/EEC, come emendata dalla

direttiva 93/68/EEC.

Η εγκατάσταση αυτή ανταποκρίνεται στις απαιτήσεις των οδηγιών της Ευρωπαϊκής Ενωσης 89/336/EOK και 73/23/EOK,

όπως οι κανονισµοί αυτοί συµπληρώθηκαν από την οδηγία 93/68/EOK.

Este equipamento obedece às exigêcias das directivas 89/336/CEE e 73/23/CEE, na sua versão corrigida pela

directiva 93/68/CEE.

Este aparato satisface las exigencias de las Directivas 89/336/CEE y 73/23/CEE, modificadas por medio de la

93/68/CEE.

Denna utrustning uppfyller kraven enligt riktlinjerna 89/336/EEC och 73/23/EEC så som kompletteras av 93/68/

EEC.

Dette produktet oppfyller betingelsene i direktivene 89/336/EEC og 73/23/EEC i endringen 93/68/EEC.

Tämä laite täyttää direktiivien 89/336/EEC ja 73/23/EEC vaatimukset, joita on muutettu direktiivillä 93/68/EEC.

The wire which is coloured brown must be connected to

the terminal which is marked with the letter L or coloured

red.

NOTE

After replacing or changing a fuse, the fuse cover in the

plug must be replaced with a fuse cover which

corresponds to the colour of the insert in the base of the

plug or the word that is embossed on the base of the plug,

and the appliance must not be used without a fuse cover.

If lost replacement fuse covers can be obtained from your

dealer.

Only 13 A fuses approved by B.S.I or A.S.T.A to B.S.1362

should be used.

P3-4-2-1-2-1_En

The wires in this mains lead are coloured in

accordance with the following code:

Green and Yellow : Earth

Blue : Neutral

Brown : Live

If the plug provided is unsuitable for your socket outlets,

the plug must be cut off and a suitable plug fitted.

IMPORTANT

FOR USE IN THE UNITED

KINGDOM.

The cut-off plug should be disposed of and must not be

inserted into any 13 amp socket as this can result in

electric shock. The plug or adaptor or the distribution

panel should be provided with 13 A fuse. As the colours of

the wires in the mains lead of this appliance may not

correspond with coloured markings identifying the

terminals in your plug, proceed as follows ;

The wire which is coloured green and yellow must be

connected to the terminal in the plug which is marked

with the letter E or by the earth symbol , or coloured

green or green and yellow.

The wire which is coloured blue must be connected to the

terminal which is marked with the letter N or coloured

black.

Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified service

personnel.

English

WARNING

This apparatus must be earthed.

The following symbols are found on

labels attached to the product. They alert

the operators and service personnel of

this equipment to any potentially

dangerous conditions.

STANDBY/ON Button

STANDBY: When placed into the standby mode, the main

power flow is cut and the unit is no longer fully

operational.

STANDBY/ON Indicator

The indicator is lit red when the unit is in the standby mode

and is lit blue when it is in the power-on mode.

WARNING

This equipment is not waterproof. To prevent a fire or

shock hazard, do not place any container filed with liquid

near this equipment (such as a vase or flower pot) or

expose it to dripping, splashing, rain or moisture.

D3-4-2-1-3_A_En

This product complies with the Low Voltage Directive (73/23/EEC,

amended by 93/68/EEC), EMC Directives (89/336/EEC, amended by

92/31/EEC and 93/68/EEC).

WARNING

The voltage of the available power supply differs according

to country or region. Be sure that the power supply voltage

of the area where this unit will be used meets the required

voltage (e.g., 230V or 120V) written on the rear panel.

D3-4-2-1-4_A_En

Before plugging in for the first time, read the following

section carefully.

WARNING

This product equipped with a three-wire grounding

(earthed) plug - a plug that has a third (grounding) pin. This

plug only fits a grounding-type power outlet. If you are

unable to insert the plug into an outlet, contact a licensed

electrician to replace the outlet with a properly grounded

one. Do not defeat the safety purpose of the grounding

plug.

D3-4-2-1-6_A_En

WARNING

This symbol refers to a hazard or unsafe

practice which can result in personal

injury or property damage.

CAUTION

This symbol refers to a hazard or unsafe

practice which can result in severe

personal injury or death.

WARNING

To prevent a fire hazard, do not place any naked flame

sources (such as a lighted candle) on the equipment.

D3-4-2-1-7a_A_En

VENTILATION CAUTION

When installing this unit, make sure to leave space around

the unit for ventilation to improve heat radiation. For the

minimum space required, see page 15.

WARNING

Slots and openings in the cabinet are provided for

ventilation to ensure reliable operation of the product, and

to protect it from overheating. To prevent fire hazard, the

openings should never be blocked or covered with items

(such as newspapers, table-cloths, curtains) or by operating

the equipment on thick carpet or a bed.

CAUTION

The power switch does not completely separate the unit

from the mains in off position. Therefore install the unit

suitable places easy to disconnect the mains plug in case of

the accident. The mains plug of unit should be unplugged

from the wall socket when left unused for a long period of

time.

4

En

Contents

Thank you for buying this Pioneer product.

Please read through these operating instructions so you will know how to operate your model properly. After you have finished

reading the instructions, put them away in a safe place for future reference.

In some countries or regions, the shape of the power plug and power outlet may sometimes differ from that shown in the

explanatory drawings. However the method of connecting and operating the unit is the same.

01 Important User Guidance Information

02 Safety Precautions

03 Supplied Accessories

Plasma Display ..........................................11

Media Receiver ..........................................11

04 Part Names

Plasma Display ..........................................12

Media Receiver ..........................................13

Remote control unit ..................................14

05 Preparation

Installing the Plasma Display ..................15

Installing the Media Receiver ..................15

Preventing the Plasma Display from

Falling Over ................................................16

Connecting the system cable ..................17

Routing cables ..........................................18

Preparing the remote control unit ...........19

Inserting batteries ................................19

Cautions regarding batteries ...............19

Allowed operation range of the remote

control unit ............................................19

Cautions regarding the remote control

unit .........................................................19

Basic connections ....................................20

Connecting to an antenna ...................20

Connecting the power cord .................20

06 Watching TV

Turning on/ off the power .........................21

Changing channels ...................................22

Tuning to your favourite channels ...........23

Changing the volume and sound ............23

Freezing images ........................................25

07 Menu Setup

Using the menu .........................................26

Menu operations ..................................26

08 Basic Adjustment Settings

Setting up TV channels automatically .....27

Using Auto Installation ........................27

Setting up TV channels manually ........... 27

Using Manual Adjust .......................... 27

Reducing video noise .......................... 28

Setting Child Lock ............................... 28

Selecting a decoder input terminal ... 28

Labelling TV channels ......................... 29

Sorting preset TV channels ................. 29

Clock setting ........................................ 29

Language setting ...................................... 30

AV Selection ............................................. 30

Basic picture adjustments ...................... 31

Advanced picture adjustments ............... 31

Using PureCinema .............................. 31

Using Colour Temp .............................. 32

Using CTI .............................................. 32

Using Colour Management ................ 32

Eliminating noise from images .......... 33

Using the Dynamic Range Expander

(DRE) functions ................................... 33

Using the 3DYC and I-P Mode ............ 33

Sound adjustments .................................. 34

FOCUS .................................................. 34

Front Surround .................................... 34

Power Control ........................................... 35

09 Useful Adjustment Settings

Switching the vertical drive frequency ... 36

Adjusting image positions ....................... 36

Selecting an input signal type ................. 36

Colour system setting .............................. 36

Selecting a screen size manually ........... 37

Selecting a screen size automatically .... 37

Selecting a screen size for received

4:3 aspect ratio signals ....................... 37

Changing the brightness at both sides

of the screen (Side Mask) ........................ 38

Sleep Timer ............................................... 38

Using a password ..................................... 38

Entering a password ........................... 38

Changing the password ...................... 39

Resetting the password function ....... 39

Disabling the password function ....... 39

5

En

Contents

English

10 Enjoying through External Equipment

Watching a decoder image ..................... 40

Connecting a decoder ......................... 40

Displaying a decoder image ............... 40

Watching a VCR image ............................ 40

Connecting a VCR ............................... 40

Displaying a VCR image ...................... 40

Using HDMI Input .................................... 41

Connecting HDMI equipment ............ 41

Using i/o Link.A ........................................ 42

Watching a DVD image ........................... 42

Connecting a DVD player .................... 42

Displaying a DVD image ..................... 42

Enjoying a game console or watching

camcorder images ................................... 43

Connecting a game console or

camcorder ............................................ 43

Displaying an image from the game

console or camcorder ......................... 43

Enjoying through audio equipment in

connection ................................................ 43

Connecting audio equipment ............. 43

11 Using the Teletext Functions

What is Teletext? ....................................... 44

Operating the Teletext basics .................. 44

Turning on and off Teletext ................. 44

Selecting and operating Teletext

pages .................................................... 44

Displaying subpages ........................... 45

Displaying TOP Over View ................... 45

Displaying subtitle pages .................... 45

12 Appendix

Troubleshooting ........................................ 46

Connecting pin assignments for

SCART ....................................................... 47

Specifications ........................................... 48

6

En

Important User Guidance Information

01

Important User Guidance Information

In order to obtain maximum enjoyment from this Pioneer

PureVision PDP-506FDE/PDP-436FDE Plasma Display System,

please first read this information carefully.

With the Pioneer PureVision PDP-506FDE/PDP-436FDE, you

can be assured of a high quality Plasma Display System with

long-life and high reliability. To achieve images of exceptional

quality, this Pioneer Plasma Display System incorporates

state-of-the-art design and construction, as well as very precise

and highly advanced technology.

The Pioneer PureVision PDP-506FDE/PDP-436FDE

incorporates the latest in colour filter technology – Direct

Colour Filter. This improves the colour / picture reproduction of

these models as compared to previous models. It also

eliminates the need for a physical glass panel to be placed in

front of the plasma panel, which furthers Pioneer’s continued

goal of reducing environmental waste in consumer

electronics, now during the manufacturing process and in the

future during the recycling process.

Over the course of its lifetime, the luminosity of the Pioneer

PDP-506FDE/PDP-436FDE Plasma Display System will

diminish very slowly, such as with all phosphor-based screens

(for example, a traditional tube-type television). To enjoy

beautiful and bright images on your Pioneer Plasma Display

System for a long time, please carefully read and follow the

usage guidances below:

Usage guidelines

All phosphor-based screens (including conventional tube-type

televisions) can be affected by displaying static images for a

prolonged period. Plasma Display System’s are no exception to

this rule. After-image and permanent effects on the screen can

be avoided by taking some basic precautions. By following the

recommendations listed below, you can ensure longer and

satisfactory results from your plasma:

• Whenever possible, avoid frequently displaying the same

image or virtually still moving pictures (e.g. closed-captioned

images or video game images which have static portions).

• Do not display Teletext for a prolonged period of time.

• Avoid viewing the On Screen Display for extended periods,

from a decoder, DVD player, VCR and all other components.

• Do not leave the same picture freeze-framed or paused

continuously over a long period of time, when using the still

picture mode from a TV, VCR, DVD player or any other

component.

• Images which have both very bright areas and very dark

areas side by side should not be displayed for a prolonged

period of time.

• When playing a game, the “GAME” mode setting within “AV

Selection” is strongly recommended. However, please limit

its use to less than 2 hours at a time.

• After playing a game or displaying any still image, it is best

to view a normal moving picture in the “WIDE” or “FULL”

screen setting for more than 3 times the length of the

previous still moving image.

• After using the Plasma Display System, always switch the

display to “STANDBY” mode.

Installation guidelines

The Pioneer PureVision PDP-506FDE/PDP-436FDE Plasma

Display System incorporates a very thin design. To ensure

safety, please take the proper measures to mount or install the

Plasma Display, in order to prevent the unit from tipping over

in the event of vibration or accidental movement.

This product should be installed by using only parts and

accessories designed by PIONEER. Use of accessories other

than the PIONEER stand or installation bracket may result in

instability, and could cause injury. For custom installation,

please consult the dealer where the unit was purchased. To

ensure correct installation, experienced and qualified experts

must install the unit. PIONEER will not be held responsible for

accident or damage caused by the use of parts and

accessories manufactured by other companies.

To avoid malfunction and overheating, make sure that the

vents on the main unit are not blocked when installing to

ensure proper heat emission:

• Distance the unit slightly from other equipment, walls, etc.

For the minimum space required around the unit, see page

15.

• Do not fit the unit inside narrow spaces where ventilation is

poor.

• Do not cover with a cloth, etc.

• Clean the vents on the sides and rear of the unit to remove

dust build-up, by using a vacuum cleaner set to its lowest

suction setting.

• Do not place the product on a carpet or blanket.

• Do not leave the product tilted over except the case of vertical

installation of the Media Receiver.

• Do not reverse the product.

Using the unit without proper ventilation may cause the

internal temperature to rise, and could result in possible

malfunction. When the surrounding or internal temperature

exceeds a certain degree, the display will automatically power

off in order to cool the internal electronics and prevent

hazardous occurrences.

Any malfunction may occur due to: an inappropriate

installation site, improper assembly, installation, mounting, or

operation of this product, modifications made to the product.

However, PIONEER cannot be held responsible for such

accidents or malfunction.

NOTE

The following are typical effects and characteristics of a

phosphor-based matrix display and as such, are not covered by

the manufacturer’s limited warranties:

• Permanent residual images upon the phosphors of the

panel.

• The existence of a minute number of inactive light cells.

• Panel generated sounds, examples: Fan motor noise, and

electrical circuit humming / glass panel buzzing

7

En

Important User Guidance Information

01

English

CAUTION

PIONEER bears no responsibility for any damage arising from

incorrect use of the product by you or other people,

malfunctions when in use, other product related problems,

and use of the product except in cases where the company

must be liable.

Plasma Display protection function

When still images (such as photos and computer images) stay

on the screen for an extended period of time, the screen will be

slightly dimmed. This is because the protection function of the

Plasma Display automatically adjusts the brightness to protect

the screen when detecting still images; so this does not

designate malfunction. The screen is dimmed when a still

image is detected for about three minutes.

Information of pixel defect

Plasma screens display information using pixels. Pioneer

plasma display panels contain a very large number of pixels.

(Depending on the panel size; over 2.3 million cells in case of a

43 inch display, over 2.9 million pixels in case of a 50 inch

display, over 3.1 million cells in case of a 61 inch display). All

Pioneer display panels are manufactured using a very high

level of ultra-precision technology and undergo individual

quality control.

In rare cases, some pixels can be permanently switched off, or

on, resulting in either a black or coloured pixel permanently

fixed on the screen.

This effect is common to all plasma displays because it is a

consequence of the technology.

If the defective pixels are visible at a normal viewing distance

of between 2.5 and 3.5 meters whilst viewing a normal

broadcast (i.e. not a test card, still image or single colour

display) please contact the supplying dealer.

If, however, they can only be seen close up or during single

colour displays then this is considered normal for this

technology.

Infrared rays

The Plasma Display releases infrared rays because of its

characteristics. Depending on how the Plasma Display is in

use, the remote controls of nearby equipment may be

adversely affected or wireless headphones using infrared rays

are interfered by noise. If this is the case, place that equipment

at a location where its remote control sensor is not affected.

Radio interference

While this product meets the required specifications, it emits a

small amount of noise. If you place such equipment as an AM

radio, personal computer, and VCR close to this product, that

equipment may be interfered. If this happens, place that

equipment far enough from this product.

Plasma Display driving sound

The screen of the Plasma Display is composed of extremely

fine pixels and these pixels emit light according to received

video signals. This principle may make you hear buzz sound or

electrical circuit hamming from the Plasma Display.

Also note that the rotation speed of the cooling fan motor

increases when the ambient temperature of the Media

Receiver becomes high. You may hear the sound of the fan

motor at that time.

Do not attach such items as labels and tape to the

product.

• This may result in the discolouration or scratch of the

cabinet.

When not using the product for a long period of

time

• If you do not use the product for a long period of time, the

functions of the product may be adversely affected. Switch

on and run the product occasionally.

Condensation

• Condensation may take place on the surface or inside of the

product when the product is rapidly moved from a cold place

to a warm place or just after a heater is switched on in winter

morning, for example. When condensation takes place, do

not switch on the product and wait until condensation

disappears. Using the product with condensation may result

in malfunction.

Cleaning the surface of the screen and the glossy

surface of the front cabinet

• When cleaning the surface of the screen or the glossy

surface of the front cabinet, gently wipe it with a dry soft

cloth; the supplied cleaning cloth or other similar cloths

(e.g., cotton and flannel). If you use a dusty or hard cloth or

if you rub the screen hard, the surface of the product will be

scratched.

• If you clean the surface of the screen with a wet cloth, water

droplets on the surface may enter into the product, resulting

in malfunction.

Cleaning the cabinet

• When cleaning the cabinet of this product, gently wipe it

with a clean soft cloth (e.g., cotton and flannel). If you use a

dusty or hard cloth or if you rub the cabinet hard, the surface

of the cabinet will be scratched.

• The cabinet of this product is mostly composed of plastic. Do

not use chemicals such as benzene or thinner to clean the

cabinet. Using these chemicals may result in quality

deterioration or coating removal.

• Do not expose the product to volatile gas or fluid such as

pesticide. Do not make the product contact with rubber or

vinyl products for a long period of time. The effect of

plasticizer in the plastic may result in quality deterioration or

coating removal.

• If you clean the surface of the cabinet with a wet cloth, water

droplets on the surface may enter into the product, resulting

in malfunction.

Handles at the rear of the Plasma Display

• Do not remove the handles from the rear of the Plasma

Display.

• When moving the Plasma Display, ask another person for

help and use the handles attached to the rear of the Plasma

Display. Do not move the Plasma Display by holding only a

single handle. Use the handles as shown.

• Do not use the handles to hang the product when installing

or carrying the product, for example. Do not use the handles

for the purpose of preventing the product from tilting over.

8

En

Important User Guidance Information

01

CAUTION

Panel sticking and after-image lag

• Displaying the same images such as still images for a long

time may cause after-image lagging. This may occur in the

following two cases.

1 After-image lagging due to remaining electrical load

When image patterns with very high peak luminance are

displayed for more than 1 minute, after-image lagging may

occur due to the remaining electric load. The after-images

remaining on the screen will disappear when moving images

are displayed. The time for the after-images to disappear

depends on the luminance of the still images and the time they

had been displayed.

2 After-image (lag image) due to burning

Avoid displaying the same image on the Plasma Display

continuously over a long period of time. If the same image is

displayed continuously for several hours, or for shorter periods

of time over several days, a permanent after-image may remain

on the screen due to burning of the fluorescent materials.

Such images may become less noticeable if moving images

are later displayed, but they will not disappear completely.

• The energy save function can be set to help prevent damage

from screen burning (see page 35).

If you want to dispose this product, do not mix it with general household waste. There is a separate collection system for used electronic products in

accordance with legislation that requires proper treatment, recovery and recycling.

Private households in the 25 member states of the EU, in Switzerland and Norway may return their used electronic products free of charge to designated collection

facilities or to a retailer (if you purchase a similar new one).

For countries not mentioned above, please contact your local authorities for the correct method of disposal.

By doing so you will ensure that your disposed product undergoes the necessary treatment, recovery and recycling and thus prevent potential negative effects on the

environment and human health.

9

En

Safety Precautions

02

English

Safety Precautions

Electricity is used to perform many useful functions, but it can

also cause personal injuries and property damage if improperly

handled. This product has been engineered and manufactured

with the highest priority on safety. However, improper use can

result in electric shock and/or fire. In order to prevent potential

danger, please observe the following instructions when

installing, operating and cleaning the product. To ensure your

safety and prolong the service life of your product, please read

the following precautions carefully before using the product.

1. Read instructions — All operating instructions must be

read and understood before the product is operated.

2. Keep this manual in a safe place — These safety and

operating instructions must be kept in a safe place for

future reference.

3. Observe warnings — All warnings on the product and in

the instructions must be observed closely.

4. Follow instructions — All operating instructions must be

followed.

5. Cleaning — Unplug the power cord from the AC outlet

before cleaning the product. To clean the product, use the

supplied cleaning cloth or other soft clothes (e.g., cotton,

flannel). Do not use liquid cleaners or aerosol cleaners.

6. Attachments — Do not use attachments not

recommended by the manufacturer. Use of inadequate

attachments can result in accidents.

7. Water and moisture — Do not use the product near water,

such as bathtub, washbasin, kitchen sink and laundry tub,

swimming pool and in a wet basement.

8. Stand — Do not place the product on an unstable cart,

stand, tripod or table. Placing the product on an unstable

base can cause the product to fall, resulting in serious

personal injuries as well as damage to the product. Use

only a cart, stand, tripod, bracket or table recommended by

the manufacturer or sold with the product. When mounting

the product on a wall, be sure to follow the manufacturer’s

instructions. Use only the mounting hardware

recommended by the manufacturer.

9. When relocating the product placed on a cart, it must be

moved with utmost care. Sudden stops, excessive force

and uneven floor surface can cause the product to fall from

the cart.

10. Ventilation — The vents and other openings in the cabinet

are designed for ventilation. Do not cover or block these

vents and openings since insufficient ventilation can cause

overheating and/or shorten the life of the product. Do not

place the product on a bed, sofa, rug or other similar

surface, since they can block ventilation openings. This

product is not designed for built-in installation; do not

place the product in an enclosed place such as a bookcase

or rack, unless proper ventilation is provided or the

manufacturer’s instructions are followed.

11. Power source — This product must operate on a power

source specified on the specification label. If you are not

sure of the type of power supply used in your home, consult

your dealer or local power company.

12. Power cord protection — The power cords must be routed

properly to prevent people from stepping on them or

objects from resting on them. Check the cords at the plugs

and product.

13. The plasma Display used in this product is made of glass.

Therefore, it can break when the product is dropped or

applied with impact. Be careful not to be injured by broken

glass pieces in case the plasma Display breaks.

14. Overloading — Do not overload AC outlets or extension

cords. Overloading can cause fire or electric shock.

15. Entering of objects and liquids — Never insert an object

into the product through vents or openings. High voltage

flows in the product, and inserting an object can cause

electric shock and/or short internal parts. For the same

reason, do not spill water or liquid on the product.

16. Servicing — Do not attempt to service the product yourself.

Removing covers can expose you to high voltage and other

dangerous conditions. Request a qualified service person

to perform servicing.

17. Repair — If any of the following conditions occurs, unplug

the power cord from the AC outlet, and request a qualified

service person to perform repairs.

a. When the power cord or plug is damaged.

b.When a liquid was spilled on the product or when objects

have fallen into the product.

c. When the product has been exposed to rain or water.

d.When the product does not operate properly as

described in the operating instructions.

Do not touch the controls other than those described in

the operating instructions. Improper adjustment of

controls not described in the instructions can cause

damage, which often requires extensive adjustment work

by a qualified technician.

e. When the product has been dropped or damaged.

f. When the product displays an abnormal condition. Any

noticeable abnormality in the product indicates that the

product needs servicing.

18. Replacement parts — In case the product needs

replacement parts, make sure that the service person uses

replacement parts specified by the manufacturer, or those

with the same characteristics and performance as the

original parts. Use of unauthorized parts can result in fire,

electric shock and/or other danger.

19. Safety checks — Upon completion of service or repair work,

request the service technician to perform safety checks to

ensure that the product is in proper operating condition.

20. Wall or ceiling mounting — When mounting the product

on a wall or ceiling, be sure to install the product according

to the method recommended by the manufacturer.

21. Heat sources — Keep the product away from heat sources

such as radiators, heaters, stoves and other heat-

generating products (including amplifiers).

22. Unplug the power cord from the AC outlet before installing

the speakers.

23. Never expose the screen of the Plasma Display to a strong

impact, for example, by hitting it. The screen may be

broken, resulting in fire or personal injury.

24. Do not expose the Plasma Display to direct sunlight for a

long period of time. The optical characteristics of the front

protection panel changes, resulting in discolouration or

warp.

25. The Plasma Display weighs about 31.8 kg (70.1 lbs.) for the

PDP-506PE and about 25.8 kg (56.9 lbs.) for the PDP-

436PE. Because it has small depth and is unstable,

unpack, carry, and install the product with one more

person at least and use the handles.

10

En

Safety Precautions

02

Installation Precautions

Observe the following precautions when installing with any items such as the optional stand.

When using the optional stand, brackets, or equivalent items

• Ask your dealer to perform the installation.

• Be sure to use the supplied bolts.

• For details, see the instruction manual that comes with the optional stand (or equivalent items).

When using other items

• Consult your dealer.

• The following six mounting holes can be used for the installation:

CAUTION

• Be sure to use four or more mounting holes symmetrical to the vertical and horizontal median lines.

• Use M8 screws, which go 12 to 18 mm in depth from the mounting surface of the Plasma Display. See the side view above.

• Be careful not to block the ventilation opening at the rear of the Plasma Display.

• Be sure to install the Plasma Display on a flat surface because it contains glass.

• The screw holes other than the above are to be used only for the specified products. Never use them for mounting non-specified

products.

• Do not mount or remove the Plasma Display to or from the stand, with speakers attached.

NOTE

• It is strongly recommended to use the optional PIONEER mounting products.

• PIONEER shall not be liable for any personal injury or product damage that results from the use of mounting items other than

the optional PIONEER products.

SYSTEM

CABLE

WHITE

BLACK

Rear view Side view

Mounting hole Mounting hole

Median line

Mounting surface

Plasma

Display

Mounting

bracket (or

equivalent item)

M8 screw

12 to 18 mm

11

En

Supplied Accessories

03

English

Supplied Accessories

Plasma Display

Media Receiver

NOTE

• Always use the power cord supplied with the Plasma Display

and the one supplied with the Media Receiver for each

respective unit.

Power cord (2 m)

(For Europe, except UK

and Eire)

(For UK and Eire)

Only the power cord that is appropriate in your country or region

is supplied.

Speed clamp x 3 Bead band x 3 Warranty card

Cleaning cloth

Ferrite core

Cable tie

Power cord (2 m)

(For Europe, except UK

and Eire)

(For UK and Eire)

Only the power cord that is appropriate in your country or region

is supplied.

AA size battery x 2

Remote control unit

System cable (3 m) Two operating instructions

12

En

Part Names

04

Part Names

Plasma Display

1POWER

button

2

STANDBY indicator

3

POWER ON indicator

4

Remote control sensor

5

SPEAKER (right/left) terminals

6

SYSTEM CABLE terminal (BLACK)

7

SYSTEM CABLE terminal (WHITE)

8

AC IN terminal

4

2

3

1

Front view

SYSTEM

CABLE

WHITE

BLACK

SYSTEM

CABLE

WHITE

BLACK

5

6

7

8

Rear view

13

En

Part Names

04

English

Media Receiver

1

POWER ON indicator

2

STANDBY indicator

3 STANDBY/ON

button

4INPUT

button

5 VOLUME +/–

buttons

6 CHANNEL +/–

buttons

7

INPUT 4 terminal (S-VIDEO)

8

INPUT 4 terminal (VIDEO)

9

INPUT 4 terminals (AUDIO)

1

ANT (Antenna) input terminal

2

RS-232C terminal (used for factory setup)

3

i/o link.A SELECT switch

4

INPUT 1 terminal (SCART)

5

INPUT 2 terminal (SCART)

6

INPUT 3 terminal (SCART)

7

INPUT 2 terminals

(COMPONENT VIDEO: Y, P

B

, P

R

)

8

AUDIO OUTPUT terminals

9

INPUT 3 terminal (HDMI)

10

SYSTEM CABLE terminal (BLACK)

11

SYSTEM CABLE terminal (WHITE)

12

AC IN terminal

ON STANDBY

STANDBY

/

ON

INPUT

-

VOLUME

+

-

CHANNEL

+

S

-

VIDEO VIDEO L AUDIO R

INPUT 4

ON STANDBY

STANDBY

/

ON

PULL

OPEN

1 2

3 4 7 85 96

Front view

Pull this section to open the door.

ANT

INPUT 2

INPUT 1

SERVICE ONLY

INPUT

I

/

o link. A

SELECT

INPUT 2

INPUT 3

HDMI

SYSTEM CABLE

BLACK WHITE

COMPONENT VIDEO

23

Y

P

B PR

AC IN

R

-

AUDIO

-

L

AUDIO OUTPUT

1

2 8

3 54 6

7

10 11 12

9

Rear view

14

En

Part Names

04

Remote control unit

NOTE

• When using the remote control unit, point it at the Plasma

Display.

1 a

Turns on the power to the Plasma Display or places it into

the standby mode.

2INPUT

Selects an input source of the Plasma Display. (INPUT 1,

INPUT 2, INPUT 3, INPUT 4)

3 0 – 9

TV/External input mode: Selects a channel.

TELETEXT mode: Selects a page.

4 p

y

Displays the channel information.

5 P +/P –

TV/External input mode: Selects a channel.

w/x

TELETEXT mode: Selects a page.

6 g

Sets the sound multiplex mode.

7

RETURN

Restores the previous menu screen.

8

///

Selects a desired item on the setting screen.

ENTER

Executes a command.

9 Colour (RED/GREEN/YELLOW/BLUE)

TELETEXT mode: Selects a page.

10 [

Jumps to the teletext subtitle page.

11 k

Displays hidden characters.

12 f

TV/External input mode: Selects the screen size.

v

TELETEXT mode: Switches Teletext images. (full/upper

half/lower half)

13 d

TV/External input mode: Freezes a frame from a moving

image. Press again to cancel the function.

TELETEXT mode: Stops updating Teletext pages. Press

again to release the hold mode.

14 i

+/

i

–

Sets the volume.

15 e

Mutes the sound.

16 HOME MENU

TV/External Input mode: Displays the Menu screen.

17 m

Selects the TELETEXT mode.

(all TV image, all TEXT image, TV/TEXT image)

18 l

TELETEXT mode: Displays an Index page for the CEEFAX/

FLOF format. Displays a TOP Over View page for the TOP

format.

1

2

3

4

6

7

8

9

10

11

12

13

14

15

16

17

18

5

15

En

Preparation

05

English

Preparation

Installing the Plasma Display

Location

• Avoid direct sunlight. Maintain adequate ventilation.

• The length of the system cable used to connect the Plasma

Display and the Media Receiver is about 3 m.

• Because the Plasma Display is heavy, be sure to have

someone help you when moving it.

CAUTION

• If you place anything on the top of the Media Receiver, it will

not receive enough ventilation and will not operate properly.

NOTE

• Allow enough space around the upper and back parts when

installing to ensure adequate ventilation of the rear of the

unit.

Using the optional PIONEER stand

For details on installation, refer to the instruction manual

supplied with the stand.

Using the optional PIONEER speakers

For details on installation, refer to the instruction manual

supplied with the speaker.

CAUTION

Installing the Media Receiver

CAUTION

• Do not place a VCR or any other device on the top

of the Media Receiver.

• When installing, allow enough space on the sides

and above the Media Receiver.

• Do not block the side ventilation opening or the

rear exhaust opening of the Media Receiver.

CAUTION

Placing the Media Receiver alone in the vertical position can

result in product damage and malfunction.

Over 50 cm

Over

10 cm

Operating Environment

Operating environment temperature and humidity:

+0 ºC – +40 ºC; less than 85 %RH (cooling vents not blocked)

Do not install this unit in a poorly ventilated area, or in locations

exposed to high humidity or direct sunlight (or strong artificial

light)

ON STANDBY

STANDBY

/

ON

PULL

OPEN

Plasma Display

Media Receiver

System cable

(approx. 3 m)

ON STANDBY

STANDBY

/

ON

PULL

OPEN

Over 5 cm

Over 5 cm Over 5 cm

Over 10 cm

Exhaust

opening

Ventilation

opening

ON

STANDBY

/

ON

PULL

OPEN

16

En

Preparation

05

Preventing the Plasma Display from Falling Over

After installing the stand, be sure to take special care to ensure that the Plasma Display will not fall over.

Stabilizing on a table or floor

Stabilize the Plasma Display as shown in the diagram using

screws that are available on the market.

NOTE

To stabilize the Plasma Display on a table or on the floor, use

screws that have a nominal diameter of 6 mm and that are at

least 20 mm long.

CAUTION

A table or an area of the floor with adequate strength should

always be used to support the Plasma Display. Failure to do so

could result in personal injury and physical damage.

When installing the Plasma Display, please take the necessary

safety measures to prevent it from falling or overturning in case

of emergencies, such as earthquakes, or of accidents.

If you do not take these precautions, the Plasma Display could

fall down and cause injury.

The screws, hooks, chains and other fittings that you use to

secure the Plasma Display to prevent it from overturning will

vary according to the composition and thickness of the surface

to which it will be attached.

Select the appropriate screws, hooks, chains, and other fittings

after first inspecting the surface carefully to determine its

thickness and composition and after consulting a professional

installer if necessary.

Using a wall for stabilization

1. Attach falling prevention bolts (hooks) to

the Plasma Display.

2. Use strong cords or chains to stabilize it

appropriately and firmly to a wall, pillar, or

other sturdy element.

• Perform this work in the same way on the left and right sides.

NOTE

Use hooks, ropes, chains, and fittings that are available on the

market.

Recommended hook: Nominal diameter 8 mm Length 12 to 15

mm

20 mm min.

9 to 15 mm

6 mm

12 to 15 mm

8M

Hook

Cord or chain

Fitting

1

2

17

En

Preparation

05

English

Connecting the system cable

ANT

INPUT 2

INPUT 1

SERVICE ONLY

INPUT

I

/

o link. A

SELECT

INPUT 2

INPUT 3

HDMI

SYSTEM CABLE

BLACK WHITE

COMPONENT VIDEO

23

Y

P

B

P

R

AC IN

R

-

AUDIO

-

L

AUDIO OUTPUT

SYSTEM

CABLE

WHITE

BLACK

SYSTEM

CABLE

WHITE

BLACK

Connecting the system cable to the Media Receiver

Media Receiver (rear view)

(BLACK)

(WHITE)

For details on optional PIONEER speaker

installation, refer to the instruction manual

that came with the speaker.

System cable

(BLACK)

(WHITE)

Plasma Display (rear view)

Connecting the system cable to the Plasma Display

18

En

Preparation

05

Routing cables

Speed clamps and bead bands are supplied for bunching cables. Once properly bunched, follow the steps below to route the

cables.

Attaching speed clamps to the main unit

Attach the speed clamps using the 2 holes marked with

below, depending on your routing system.

Attaching and removing speed clamps

Insert [1] into an appropriate hole on the rear of the Plasma

Display and snap [2] into the back of [1] to lock the clamp.

Speed clamps are designed to be difficult to undo once in

place. Please attach them carefully.

Use pliers to twist the clamp 90°, pulling outward. The clamp

may deteriorate over time and become damaged if removed.

When the speakers are installed at the bottom (PDP-436FDE only)

NOTE

• Use the supplied bead bands as necessary.

*Cable binder

Using the cable binders supplied with the stand, put the

speaker and system cables together so that the cables are

invisible from the front. At that time be careful not to apply

any force to the connection sections of the cables.

SYSTEM

CABLE

WHITE

BLACK

When the speakers are installed on the sides (rear view)

Speaker cable

Speed clamp

Cable binder (supplied

with the stand)*

Speed clamp

SYSTEM

CABLE

WHITE

BLACK

1

2

SYSTEM

CABLE

WHITE

BLACK

Speaker cable

Cable binders (supplied

with the stand)*

19

En

Preparation

05

English

Preparing the remote control unit

Inserting batteries

1 Open the battery cover.

2 Load the supplied two AA size batteries while inserting

their respective negative polarity (–) ends first.

• Place batteries with their terminals corresponding to the

(+) and (–) indicators in the battery compartment.

3 Close the battery cover.

Cautions regarding batteries

Improper use of batteries can result in chemical leakage or

explosion. Be sure to follow the instructions below.

• When you replace the batteries, use manganese or alkaline

ones.

• Place the batteries with their terminals corresponding to the

(+) and (–) indicators.

• Do not mix batteries of different types. Different types of

batteries have different characteristics.

• Do not mix old and new batteries. Mixing old and new

batteries can shorten the life of new batteries or cause

chemical leakage in old batteries.

• Remove batteries as soon as they have worn out. Chemicals

that leak from batteries can cause a rash. If you find any

chemical leakage, wipe thoroughly with a cloth.

• The batteries supplied with this product may have a shorter

life expectancy due to storage conditions.

• If you will not use the remote control unit for an extended

period of time, remove the batteries from it.

CAUTION

• WHEN DISPOSING OF USED BATTERIES, PLEASE

COMPLY WITH GOVERNMENTAL REGULATIONS OR

ENVIRONMENTAL PUBLIC INSTRUCTION’S RULES

THAT APPLY IN YOUR COUNTRY/AREA.

Allowed operation range of the remote control

unit

Operate the remote control unit while pointing it toward the

remote control sensor (t) located at the bottom right of the

front panel of the Plasma Display. The distance from the

remote control sensor must be within 7 m and the angle

relative to the sensor must be within 30 degrees in the right,

left, upward, or downward direction.

Cautions regarding the remote control unit

• Do not expose the remote control unit to shock. In addition,

do not expose the remote control unit to liquids, and do not

place in an area with high humidity.

• Do not install or place the remote control unit under direct

sunlight. The heat may cause deformation of the unit.

• The remote control unit may not work properly if the remote

control sensor of the Plasma Display is under direct sunlight

or strong lighting. In such case, change the angle of the

lighting or Plasma Display, or operate the remote control

unit closer to the remote control sensor.

• When any obstacle exists between the remote control unit

and the remote control sensor, the remote control unit may

not function.

• As the batteries become empty, the remote control unit can

function within a shorter distance from the remote control

sensor. Replace the batteries with new ones early enough.

• The Plasma Display emits very weak infrared rays from its

screen. If you place such equipment operated through

infrared remote control as a VCR nearby, that equipment

may not receive commands from its remote control unit

properly or entirely. If this is the case, place that equipment

at a location far enough from the Plasma Display.

• Depending on the installation environment, infrared rays

from the Plasma Display may not allow this system to

properly receive commands from the remote control unit or

may shorten allowable distances between the remote

control unit and the remote control sensor. The strength of

infrared rays emitted from the screen differs, depending on

images displayed on the screen.

30º

7 m

Remote control

sensor

20

En

Preparation

05

Basic connections

Connecting to an antenna

To enjoy a clearer picture, use an outdoor antenna. The following is a brief explanation of the types of connections that are used

for a coaxial cable.

Antenna cable (commercially available)

Connecting the power cord

Plasma Display (rear view)

NOTE

• Disconnect the power cord from the power outlet, Plasma Display and Media Receiver when the system is not going to be used

for a long period of time.

ANT

INPUT 2

INPUT 1

SERVICE ONLY

INPUT

I

/

o link.A

SELECT

INPUT 2

INPUT 3

HDMI

SYSTEM CABLE

BLACK WHITE

COMPONENT VIDEO

23

Y

P

B PR

AC IN

R

-

AUDIO

-

L

AUDIO OUTPUT

• Connect the 75-ohm coaxial cable (commercially available) to the

ANT (antenna input) terminal.

If your outdoor antenna uses a 75-ohm coaxial cable with a standard DIN45325 plug

(IEC169-2), plug it into the antenna terminal at the rear of the Media Receiver.

SYSTEM

CABLE

WHITE

BLACK

SYSTEM

CABLE

WHITE

BLACK

ANT

INPUT 2

INPUT 1

SERVICE ONLY

INPUT

I

/

o link .A

SELECT

INPUT 2

INPUT 3

HDMI

SYSTEM CABLE

BLACK WHITE

COMPONENT VIDEO

23

Y

P

B PR

AC IN

R

-

AUDIO

-

L

AUDIO OUTPUT

Europe, except UK

and Eire

UK and Eire

Media Receiver (rear view)

Europe, except UK

and Eire

UK and Eire

To AC IN

Cable tie

Ferrite core

Att

ac

hi

ng

th

e

f

err

it

e core

To help prevent noise, attach the supplied ferrite core

to the connector end of the power cord as shown. Use

the supplied cable tie to prevent the ferrite core from

slipping on the cable.

As close as possible

AC power cord

To power

outlet

La page charge ...

Pioneer PDP 436PE Le manuel du propriétaire

Ce manuel convient également à

Pioneer PDP 436PE Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents