Pioneer PDP-5072 Manuel utilisateur

Enregistrez votre appareil sur:

www.pioneerelectronics.com (États-Unis)

www.pioneerelectronics.ca (Canada)

Register Your Product at

www.pioneerelectronics.com (US)

www.pioneerelectronics.ca (Canada)

PLASMA DISPLAY SYSTEM

SYSTEME D’ÉCRAN PLASMA

SISTEMA DE PANTALLA DE PLASMA

PDP-6072HD

PDP-5072HD

PDP-4272HD

PDP-6071HD

PDP-5071HD

PDP-4271HD

PDP-6070HD

PDP-5070HD

PDP-4270HD

Operating Instructions

Mode d’emploi

Manual de instrucciones

PDP6070HD.book Page 1 Friday, May 19, 2006 5:01 PM

Read these instructions.

Keep these instructions.

Heed all warnings.

Follow all instructions.

Do not use this apparatus near water.

Clean only with dry cloth.

Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

Do not install near any heat sources such as

radiators, heat registers, stoves, or other apparatus

(including amplifiers) that produce heat.

Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two

blades with one wider than the other. A grounding

type plug has two blades and a third grounding

prong. The wide blade or the third prong are

provided for your safety. If the provided plug does

not fit into your outlet, consult an electrician for

replacement of the obsolete outlet.

Protect the power cord from being walked on or

pinched particularly at plugs, convenience

receptacles, and the point where they exit from the

apparatus.

1)

2)

3)

4)

5)

6)

7)

8)

9)

10)

Only use attachments/accessories specified by the

manufacturer.

Use only with the cart, stand, tripod, bracket, or

table specified by the manufacturer, or sold with the

apparatus. When a cart is used, use caution when

moving the cart/apparatus combination to avoid

injury from tip-over.

Unplug this apparatus during lightning storms or

when unused for long periods of time.

Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or

plug is damaged, liquid has been spilled or objects

have fallen into the apparatus, the apparatus has

been exposed to rain or moisture, does not operate

normally, or has been dropped.

11)

12)

13)

14)

WARNING: This product equipped with a three-

wire grounding (earthed) plug - a plug that has a third

(grounding) pin. This plug only fits a grounding-type

power outlet. If you are unable to insert the plug into an

outlet, contact a licensed electrician to replace the

outlet with a properly grounded one. Do not defeat the

safety purpose of the grounding plug

D3-4-2-1-6_A_En

WARNING: To prevent a fire hazard, do not place

any naked flame sources (such as a lighted candle) on

the equipment.

D3-4-2-1-7a_A_En

NOTE TO CATV SYSTEM INSTALLER

THIS REMINDER IS PROVIDED TO CALL THE CATV

SYSTEM INSTALLER’S ATTENTION TO ARTICLE

820-40 OF THE NEC THAT PROVIDES GUIDELINES

FOR PROPER GROUNDING AND, IN PARTICULAR,

SPECIFIES THAT THE CABLE GROUND SHALL BE

CONNECTED TO THE GROUNDING SYSTEM OF

THE BUILDING, AS CLOSE TO THE POINT OF

CABLE ENTRY AS PRACTICAL.

D1-4-2-8_En

This digital television is capable of receiving analog

basic, digital basic and digital premium cable

television programming by direct connection to a cable

system providing such programming. A security card

provided by your cable operator is required to view

encrypted digital programming. Certain advanced and

interactive digital cable services such as video-on-

demand, a cable operator’s enhanced program guide

and data-enhanced television services may require the

use of a set-top box. For more information call your

local cable operator.

VENTILATION CAUTION:

When installing this unit, make sure to leave space

around the unit for ventilation to improve heat

radiation. For the minimum space required, see page

20.

WARNING: Slots and openings in the cabinet are

provided for ventilation to ensure reliable operation of

the product, and to protect it from overheating. To

prevent fire hazard, the openings should never be

blocked or covered with items (such as newspapers,

table-cloths, curtains) or by operating the equipment

on thick carpet or a bed.

PDP6070HD.book Page 2 Friday, May 19, 2006 5:01 PM

English

WARNING: THE APPARATUS IS NOT

WATERPROOFS, TO PREVENT FIRE OR SHOCK

HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN

OR MOISTURE AND DO NOT PUT ANY WATER

SOURCE NEAR THIS APPARATUS, SUCH AS VASE,

FLOWER POT, COSMETICS CONTAINER AND

MEDICINE BOTTLE ETC.

WARNING: Handling the cord on this product or

cords associated with accessories sold with the

product will expose you to lead, a chemical known to

the State of California and other governmental entities

to cause cancer and birth defects or other reproductive

harm. Wash hands after handling.

Information to User

Alteration or modifications carried out without

appropriate authorization may invalidate the user’s

right to operate the equipment.

[For Canadian model]

This Class B digital apparatus complies with Canadian

ICES-003.

FEDERAL COMMUNICATIONS

COMMISSION DECLARATION OF

CONFORMITY

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions: (1)

This device may not cause harmful interference, and

(2) this device must accept any interference received,

including interference that may cause undesired

operation.

Product Name: Plasma Display System

Model Number: PDP-6072HD/PDP-5072HD/PDP-

4272HD/PDP-6071HD/PDP-5071HD/PDP-4271HD/

PDP-6070HD/PDP-5070HD/PDP-4270HD

Product Category: Class B Personal Computers &

Peripherals

Responsible Party Name: PIONEER ELECTRONICS

SERVICE, INC.

Address: 1925 E. DOMINGUEZ ST. LONG BEACH, CA

90801-1760, U.S.A.

Phone: 800-421-1625

For Business Customer URL

http://www.PioneerUSA.com

STANDBY: When placed into the standby mode, the main power flow is cut and the unit is no longer

fully operational.

STANDBY/ON Indicator: The indicator is lit red when the unit is in the standby mode and lit blue when it is in the

power-on mode. No operation can be performed when the indicator is off. However, the

Plasma Display system will still consume some power as long as the power cord is

inserted into the power outlet.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications. However, there is

no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

D8-10-1-2_En

CAUTION: This product satisfies FCC regulations when shielded cables and connectors are used to connect the

unit to other equipment. To prevent electromagnetic interference with electric appliances such as radios and

televisions, use shielded cables and connectors for connections.

D8-10-3a_En

IMPORTANT NOTICE – THE SERIAL NUMBER FOR THIS EQUIPMENT IS LOCATED IN THE REAR.

PLEASE WRITE THIS SERIAL NUMBER ON YOUR ENCLOSED WARRANTY CARD AND

KEEP IN A SECURE AREA. THIS IS FOR YOUR SECURITY.

D1-4-2-6-1_En

CAUTION: The power switch does not completely separate the unit from the mains in off position. Therefore

install the unit suitable places easy to disconnect the mains plug in case of the accident. The mains plug of unit

should be unplugged from the wall socket when left unused for a long period of time.

CAUTION:

Operating Environment

Operating environment temperature and humidity:

+0 ˚C to +40 ˚C (+32 ˚F to +104 ˚F), less than 85 %RH (cooling vents not blocked) Do not install this unit in a

poorly ventilated area, or in locations exposed to high humidity or direct sunlight (or strong artificial light)

PDP6070HD.book Page 3 Friday, May 19, 2006 5:01 PM

4

En

Contents

Thank you for buying this Pioneer product.

Please read through these operating instructions so you will know how to operate your model properly. After you have finished

reading the instructions, put them away in a safe place for future reference.

In some countries or regions, the shape of the power plug and power outlet may sometimes differ from that shown in the

explanatory drawings. However the method of connecting and operating the unit is the same.

Illustrations shown in this manual are for the PDP-5072HD/PDP-5071HD/PDP-5070HD unless otherwise specified.

01 Important User Guidance Information

02 Safety Precautions

03 Supplied Accessories

Speaker accessories ..................................12

04 Part Names

Plasma Display ...........................................13

Remote control unit ...................................19

05 Preparation

Installing the Plasma Display ...................20

Moving the Plasma Display .......................20

Installing the PIONEER speaker

(PDP-5072HD/PDP-5071HD/

PDP-5070HD) .............................................21

When using the hung on wall unit: .....24

Preventing the Plasma Display from

Falling Over .................................................25

Attaching/detaching the PIONEER

stand ...........................................................26

PDP-5072HD/PDP-5071HD/

PDP-5070HD ..........................................26

PDP-4272HD/PDP-4271HD/

PDP-4270HD ..........................................28

Cable connections for watching digital

and/or conventional TV channels .............29

Connecting VHF/UHF antennas and

a Cable ....................................................29

Inserting the CableCARD™ .......................29

Switching between antenna A and B .......29

Preparing the remote control unit ............30

Inserting batteries .................................30

Cautions regarding batteries ................30

Allowed operation range of the remote

control unit .............................................30

Cautions regarding the remote control

unit ..........................................................30

Connecting the power cord .......................31

Routing cables ...........................................31

06 Basic Operations

Turning on the power ................................ 32

Turning off the power ................................ 32

Watching TV channels .............................. 33

Selecting the antenna .......................... 33

Changing channels .............................. 33

Changing the volume and sound ........ 34

Changing the language ....................... 34

Setting MTS/SAP mode ....................... 35

Viewing a channel banner ................... 36

Using the POD service ......................... 36

Using the multiscreen functions ............. 36

Splitting the screen .............................. 36

Freezing images .................................... 37

07 TV Guide On Screen™ System Setup

About the TV Guide On Screen™

system ........................................................ 38

Setting up the TV Guide On Screen™

system ........................................................ 38

08 Menu Setup

Menu Configuration .................................. 42

AV mode menus ................................... 42

PC mode menus ................................... 42

Menu operations ................................... 42

09 Tuner Setup

Setting up TV channels ............................. 43

Using Auto Channel Preset ................. 43

Setting for skipping unwanted

channels ................................................ 43

Setting up TV channels manually ....... 43

Checking signal strength ..................... 43

Checking the CableCARD™ ID ............ 44

Parental Control ........................................ 44

Changing the password ....................... 44

Clearing the password ......................... 45

Activating the Parental Control ........... 45

Setting the voluntary movie rating

system (MPAA) ..................................... 45

Setting the TV ratings ........................... 45

PDP6070HD.book Page 4 Friday, May 19, 2006 5:01 PM

5

En

Contents

English

Setting the TV Parental Guidelines

(TV Guidelines) ...................................... 46

Blocking Not Rated TV programs ........ 46

Canadian rating systems ..................... 46

Setting Canadian English ratings ....... 47

Setting Canadian French ratings ........ 47

Setting new ratings .............................. 47

Deleting new ratings ............................ 48

Temporarily deactivating the Parental

Control ................................................... 48

Setting your favorite channels ................. 49

Setting up closed captions ....................... 49

Activating the closed caption .............. 49

Selecting the type of conventional

closed captions ..................................... 49

Selecting digital closed captions ........ 50

Selecting digital closed caption

parameters ............................................ 50

Clock Setting ............................................. 50

10 TV Guide On Screen™ System Operation

Using the TV Guide On Screen™

system ........................................................ 52

Screen components .................................. 52

TV Guide On Screen™ icons ................ 52

TV Guide On Screen™ navigation ....... 53

The Listings screen ................................... 53

Recording programs ................................. 54

Setting program reminders ...................... 55

Searching for programs ........................... 57

Searching by category .......................... 57

Searching by keyword .......................... 58

Alphabetical search ............................. 59

The search Episode Options menu ..... 59

Scheduling recordings and reminders ... 60

The Schedule Options menu ............... 60

Changing setup options ........................... 61

Changing the System Settings ............ 61

Changing the Channel Display

settings .................................................. 61

Changing the Default Options ............. 62

11 Adjustments and Settings

Sleep Timer ................................................ 63

AV Selection .............................................. 63

Basic picture adjustments ....................... 64

Advanced picture adjustments ................ 65

Using PureCinema ............................... 65

Using Color Temp ................................. 65

Using CTI ............................................... 65

Eliminating noise from images ........... 65

Sound adjustments ................................... 66

FOCUS ................................................... 66

Front Surround ...................................... 66

Power Control ............................................ 67

Energy Save ........................................... 67

No Signal off (AV mode only) ............... 67

No Operation off (AV mode only) ......... 67

Power Management

(PC mode only) ...................................... 67

Image position adjustment

(AV mode only) .......................................... 68

Automatic image position and clock

adjustments (PC mode only) .................... 68

Manual image position and clock

adjustments (PC mode only) .................... 68

Selecting a screen size manually ............. 69

Selecting a screen size automatically ..... 70

Selecting a screen size for received

4:3 aspect ratio signals ........................ 70

Changing the brightness at both sides

of the screen (Side Mask) ......................... 70

Language setting ....................................... 70

12 Enjoying through External Equipment

About External Equipment ....................... 71

Watching a DVD image ............................ 71

Connecting a DVD player ..................... 71

Displaying a DVD image ...................... 71

Watching a VCR image ............................. 71

Connecting a VCR ................................. 71

Displaying a VCR image ....................... 71

Using HDMI Input ..................................... 72

Connecting HDMI equipment ............. 72

Enjoying a game console or watching

camcorder images .................................... 73

Connecting a game console or

camcorder ............................................. 73

Displaying an image of the game

console or camcorder .......................... 73

Recording digital TV programs using

a VCR .......................................................... 73

Avoiding unwanted feedback .............. 73

Connecting a recorder ......................... 74

Connecting other audio equipment ......... 74

Connecting an AV receiver .................. 74

Watching an image from a personal

computer .................................................... 75

PDP6070HD.book Page 5 Friday, May 19, 2006 5:01 PM

6

En

Contents

Connecting a personal computer ........75

Displaying an image from a personal

computer ................................................75

Computer compatibility chart ...................76

G-LINK™ connection .................................76

Connecting control cords ..........................77

About SR+ .............................................77

Enjoying through USB interface

(Home Gallery function) ............................78

Readable memory cards .......................78

Readable data files ................................78

Connecting a USB device .....................78

Removing a USB device .......................78

Displaying a device list .........................79

Starting the initial Home Gallery

screen .....................................................79

Selecting a folder ..................................79

Starting a thumbnail screen .................79

Starting a standard single-image

screen .....................................................80

Starting the Slide Show Setup

screen .....................................................80

Starting the Slide Show screen ............80

13 Useful Remote Control Features

Presetting manufacturer codes to control

other devices ..............................................81

Presetting manufacturer codes ...........81

Library Search ........................................81

Manufacturing Reset ............................81

Programming codes ............................82

CABLE ....................................................82

SATELLITE ..............................................82

VCR .........................................................83

PVR .........................................................85

DVD .........................................................85

DVD-R .....................................................86

LD ............................................................86

Using the remote control unit to control

other devices ..............................................87

Receiver control buttons .......................87

CBL/SAT control buttons ......................88

VCR control buttons ..............................89

DVD/DVR control buttons .....................90

14 Appendix

Troubleshooting .........................................91

Specifications ...........................................101

PDP6070HD.book Page 6 Friday, May 19, 2006 5:01 PM

7

En

Important User Guidance Information

01

English

Important User Guidance Information

In order to obtain maximum enjoyment from this Pioneer

PureVision PDP-6072HD/PDP-5072HD/PDP-4272HD/PDP-

6071HD/PDP-5071HD/PDP-4271HD/PDP-6070HD/PDP-

5070HD/PDP-4270HD Plasma Display System, please first

read this information carefully.

With the Pioneer PureVision PDP-6072HD/PDP-5072HD/PDP-

4272HD/PDP-6071HD/PDP-5071HD/PDP-4271HD/PDP-

6070HD/PDP-5070HD/PDP-4270HD, you can be assured of a

high quality Plasma Display System with long-life and high

reliability. To achieve images of exceptional quality, this

Pioneer Plasma Display System incorporates state-of-the-art

design and construction, as well as very precise and highly

advanced technology.

The Pioneer PureVision PDP-6072HD/PDP-5072HD/PDP-

4272HD/PDP-6071HD/PDP-5071HD/PDP-4271HD/PDP-

6070HD/PDP-5070HD/PDP-4270HD incorporates the latest in

color filter technology – Direct Color Filter. This improves the

color / picture reproduction of these models as compared to

previous models. It also eliminates the need for a physical

glass panel to be placed in front of the plasma panel, which

furthers Pioneer’s continued goal of reducing environmental

waste in consumer electronics, now during the manufacturing

process and in the future during the recycling process.

Over the course of its lifetime, the luminosity of the Pioneer

PDP-6072HD/PDP-5072HD/PDP-4272HD/PDP-6071HD/PDP-

5071HD/PDP-4271HD/PDP-6070HD/PDP-5070HD/PDP-

4270HD Plasma Display System will diminish very slowly, such

as with all phosphor-based screens (for example, a traditional

tube-type television). To enjoy beautiful and bright images on

your Pioneer Plasma Display System for many years to come,

please carefully read and follow the usage guidelines below.

Usage guidelines

All phosphor-based screens (including conventional tube-type

televisions) can be affected by displaying static images for a

prolonged period. Plasma Display Systems are no exception to

this rule. After-image and permanent effects on the screen can

be avoided by taking some basic precautions. By following the

recommendations listed below, you can ensure longer and

satisfactory results from your plasma:

• Whenever possible, avoid frequently displaying the same

image or virtually still moving pictures (e.g. closed-captioned

images or video game images which have static portions).

• Avoid viewing the On Screen Display for extended periods,

from a DVD player, VCR, and all other components.

• Do not leave the same picture freeze-framed or paused

continuously over a long period of time, when using the still

picture mode from a TV, VCR, DVD player or any other

component.

• Images which have both very bright areas and very dark

areas side by side should not be displayed for a prolonged

period of time.

• When playing a game, the “GAME” mode setting within “AV

Selection” is strongly recommended. However, please limit

its use to less than 2 hours at a time.

• After playing a game, or displaying a PC image or any still

image, it is best to view a normal moving picture in the

“WIDE” or “FULL” screen setting for over 3 times longer than

the previous still/moving image.

• After using the Plasma Display System, always switch the

display to “STANDBY” mode.

• Extensive viewing of content with top, bottom, or side masks

may cause uneven wear. After viewing masked content, it is

recommended to view full screen motion video for an equal

or greater amount of time.

Installation guidelines

The Pioneer PureVision PDP-6072HD/PDP-5072HD/PDP-

4272HD/PDP-6071HD/PDP-5071HD/PDP-4271HD/PDP-

6070HD/PDP-5070HD/PDP-4270HD Plasma Display System

incorporates a very thin design. To ensure safety, please take

the proper measures to mount or install the Plasma Display, in

order to prevent the unit from tipping over in the event of

vibration or accidental movement.

This product should be installed by using only parts and

accessories designed by PIONEER. Use of accessories other

than the PIONEER stand or installation bracket may result in

instability, and could cause injury. For custom installation,

please consult the dealer where the unit was purchased. To

ensure correct installation, experienced and qualified experts

must install the unit. PIONEER will not be held responsible for

accident or damage caused by the use of parts and

accessories manufactured by other companies.

To avoid malfunction and overheating when installing, make

sure that the vents on the main unit are not blocked. To ensure

proper heat emission:

• Distance the unit slightly from other equipment, walls, etc.

For the minimum space required around the unit, see page

20.

• Do not fit the unit inside narrow spaces where ventilation is

poor.

• Do not cover with a cloth, etc.

• Clean the vents on the sides and rear of the unit to remove

dust build-up by using a vacuum cleaner set to its lowest

suction setting.

• Do not place the product on a carpet or blanket.

• Do not leave the product tilted over.

• Do not invert the product.

Using the unit without proper ventilation may cause the

internal temperature to rise, and could result in possible

malfunction. When the surrounding or internal temperature

exceeds a certain degree, the display will automatically power

off in order to cool the internal electronics and prevent a

hazardous occurrence.

Malfunction can be caused by many factors: inappropriate

installation site, improper assembly/installation/mounting,

improper operation of or modifications made to this product.

However, PIONEER cannot be held responsible for accidents

or malfunction caused by the above.

NOTE

The following are typical effects and characteristics of a

phosphor-based matrix display and as such, are not covered by

the manufacturer’s limited warranties:

• Permanent residual images upon the phosphors of the

panel.

• The existence of a minute number of inactive light cells.

• Panel generated sounds, examples: Fan motor noise, and

electrical circuit humming / glass panel buzzing

PDP6070HD.book Page 7 Friday, May 19, 2006 5:01 PM

8

En

Important User Guidance Information

01

CAUTION

PIONEER bears no responsibility for any damage arising from

incorrect use of the product by you or other people,

malfunctions when in use, other product related problems,

and use of the product except in cases where the company

must be liable.

Plasma Display protection function

When still images (such as photos and computer images) stay

on the screen for an extended period of time, the screen will be

slightly dimmed. This is because the protection function of the

Plasma Display automatically adjusts the brightness to protect

the screen when detecting still images; so this does not

designate malfunction. The screen is dimmed when a still

image is detected for about three minutes.

Information of pixel defect

Plasma screens display information using pixels. Pioneer

plasma display panels contain a very large number of pixels.

(Depending on the panel size; over 2.3 million pixels in case of

a 42 inch display, over 3.1 million pixels in case of a 50 inch

display and over 3.1 million pixels in case of a 60 inch display).

All Pioneer display panels are manufactured using a very high

level of ultra-precision technology and undergo individual

quality control.

In rare cases, some pixels can be permanently switched off, or

on, resulting in either a black or colored pixel permanently fixed

on the screen.

This effect is common to all plasma displays because it is a

consequence of the technology.

If the defective pixels are visible at a normal viewing distance of

between 2.5 and 3.5 meters (8.2 and 11.5 feet) while viewing a

normal broadcast (i.e. not a test card, still image or single color

display) please contact Pioneer Customer Support Div. (USA) or

Customer Satisfaction Dept. (CANADA). See back cover.

If, however, they can only be seen close up or during single

color displays then this is considered normal for this

technology.

Infrared rays

The Plasma Display releases infrared rays because of its

characteristics. Depending on how the Plasma Display is in

use, the remote controls of nearby equipment may be

adversely affected or wireless headphones using infrared rays

are interfered with by noise. If this is the case, place that

equipment at a location where its remote control sensor is not

affected.

Radio interference

While this product meets the required specifications, it emits a

small amount of noise. If you place such equipment as an AM

radio, personal computer, and VCR close to this product, that

equipment may be interfered. If this happens, place that

equipment far enough from this product.

Plasma Display driving sound

The screen of the Plasma Display is composed of extremely

fine pixels and these pixels emit light according to received

video signals. This principle may cause you to hear a buzz or

electrical hum coming from the Plasma Display.

Do not attach such items as labels and tape to the

product.

• This may result in the discoloration or scratch of the cabinet.

When not using the product for a long period of

time

• If you do not use the product for a long period of time, the

functions of the product may be adversely affected. Switch

on and run the product occasionally.

Condensation

• Condensation may take place on the surface or inside of the

product when the product is rapidly moved from a cold place

to a warm place or just after a heater is switched on on a

winter morning, for example. When condensation takes

place, do not switch on the product until condensation

disappears. Using the product with condensation may result

in malfunction.

Cleaning the surface of the screen and the glossy

surface of the front cabinet

• When cleaning the surface of the screen or the glossy

surface of the front cabinet, gently wipe it with a dry soft

cloth; the supplied cleaning cloth or other similar cloths

(e.g., cotton and flannel). If you use a dusty or hard cloth or

if you rub the screen hard, the surface of the product will be

scratched.

• If you clean the surface of the screen with a wet cloth, water

droplets on the surface may enter into the product, resulting

in malfunction.

Cleaning the cabinet

• When cleaning the cabinet of this product, gently wipe it

with a clean soft cloth (e.g., cotton and flannel). If you use a

dusty or hard cloth or if you rub the cabinet hard, the surface

of the cabinet will be scratched.

• The cabinet of this product is mostly composed of plastic. Do

not use chemicals such as benzene or thinner to clean the

cabinet. Using these chemicals may result in quality

deterioration or coating removal.

• Do not expose the product to volatile gas or fluid such as

pesticide. Do not bring the product in contact with rubber or

vinyl products for a long period of time. The effect of

plasticizer in the plastic may result in quality deterioration or

coating removal.

• If you clean the surface of the cabinet with a wet cloth, water

droplets on the surface may enter into the product, resulting

in malfunction.

Handles at the rear of the Plasma Display

• Do not remove the handles from the rear of the Plasma

Display.

• When moving the Plasma Display, ask another person for

help and use the handles attached to the rear of the Plasma

Display. Do not move the Plasma Display by holding only a

single handle. Use the handles as shown on page 20.

• Do not use the handles to hang the product when installing

or carrying the product, for example. Do not use the handles

for the purpose of preventing the product from tilting over.

PDP6070HD.book Page 8 Friday, May 19, 2006 5:01 PM

9

En

Important User Guidance Information

01

English

Fan motor noise

The rotation speed of the cooling fan motor increases when the

ambient temperature of the Plasma Display becomes high.

You may hear the sound of the fan motor at that time.

About the menu window size following video

format switch

The video program that you watch may be high definition (HD)

or standard definition (SD). This Plasma Display is designed to

scale to each type of definition properly. If the video program’s

definition type changes while a menu window is displayed on

the screen (for example: HD → SD or SD → HD), the menu size

may temporarily shrink or enlarge until the scaling is

completed. This may happen, for example, when you switch

between television and an external digital video recorder

(D-VHS), or when your recorded program switches between

different definition types, while the on-screen menu is being

shown.

If this happens, the menu will return to its normal size after two

to three seconds. This action is normal, and does not indicate

a problem with your Plasma Display system.

Image Retention

When a static image is left frozen on a display for several hours,

a faint imprint of the image, known as image retention, can

remain. This image retention may be temporary or permanent.

Although caused by different things, image retention can

occur on all display technologies, including plasma and LCD.

On today’s plasma displays, permanent image retention is less

of a worry. Most image retention can be improved simply by

watching moving video.

Image retention, also known as burn-in, can occur in all

phosphor-based display systems (including CRT television

systems–both direct view and projection–as well as plasma

display systems). Displaying the same still images for long

periods should be avoided as permanent image retention or

burn-in may occur. Recommended guidelines are as follows:

Do not display static images for long periods (such as still

images, fixed images from PC or TV game equipment, and/or

fixed images such as time of day indicator or channel logo

display).

Do not display content in the 4:3 aspect ratio (black or gray

bars on left and right side of content) or letter-box content

(black bars above and below content) for extended periods of

time, or use either of these viewing modes repeatedly within a

short period of time. This plasma display system is equipped

with multiple wide-screen viewing modes; use one of these

screen modes to fill the entire screen with content.

Displaying dark images after displaying still images for a

period of time may cause image retention. In most cases, the

image retention can be corrected by displaying bright images

for a similar period of time.

If you display still images on your plasma display system for

long periods of time, image retention may be irreparable.

CAUTION

Panel sticking and after-image lag

• Displaying the same images such as still images for a long

time may cause after-image lagging. This may occur in the

following two cases.

1 After-image lagging due to remaining electric load

When image patterns with very high peak luminance are

displayed more than 1 minute, after-image lagging may occur

due to the remaining electric load. The after-images remaining

on the screen will disappear when moving images are

displayed. The time for the after-images to disappear depends

on the luminance of the still images and the time they had

been displayed.

2 After-image (lag image) due to burning

Avoid displaying the same image on the Plasma Display

continuously over a long period of time. If the same image is

displayed continuously for several hours, or for shorter periods

of time over several days, a permanent after-image may remain

on the screen due to burning of the fluorescent materials.

Such images may become less noticeable if moving images

are later displayed, but they will not disappear completely.

NOTE

• When a program menu, TV Guide screen or frozen image is

displayed for 5 to 10 minutes, the system automatically turns

the image off to prevent damage from screen burning.

Preventing damage from screen burning

• It is recommended that you enjoy watching images

displayed in full screen, except when doing so may result in

copyright infringement. See page 69.

• The Energy save function can be set to help prevent damage

from screen burning. See page 67.

CAUTION

DO NOT PLACE THIS PRODUCT ON AN UNSTABLE CART,

STAND, TRIPOD, BRACKET, OR TABLE. THE PRODUCT MAY

FALL, CAUSING SERIOUS PERSONAL INJURY AND SERIOUS

DAMAGE TO THE PRODUCT. USE ONLY WITH A CART,

STAND, TRIPOD, BRACKET, OR TABLE RECOMMENDED BY

THE MANUFACTURER, OR SOLD WITH THE PRODUCT.

FOLLOW THE MANUFACTURER’S INSTRUCTIONS WHEN

INSTALLING THE PRODUCT AND USE MOUNTING

ACCESSORIES RECOMMENDED BY THE MANUFACTURER.

A PRODUCT AND CART COMBINATION SHOULD BE MOVED

WITH THE CARE. QUICK STOPS, EXCESSIVE FORCE, AND

UNEVEN SURFACES MAY CAUSE THE PRODUCT AND CART

COMBINATION TO OVERTURN.

PDP6070HD.book Page 9 Friday, May 19, 2006 5:01 PM

10

En

Safety Precautions

02

Safety Precautions

Electricity is used to perform many useful functions, but it can

also cause personal injuries and property damage if improperly

handled. This product has been engineered and manufactured

with the highest priority on safety. However, improper use can

result in electric shock and/or fire. In order to prevent potential

danger, please observe the following instructions when

installing, operating and cleaning the product. To ensure your

safety and prolong the service life of your product, please read

the following precautions carefully before using the product.

1. Read instructions—All operating instructions must be read

and understood before the product is operated.

2. Keep this manual in a safe place—These safety and

operating instructions must be kept in a safe place for

future reference.

3. Observe warnings—All warnings on the product and in the

instructions must be observed closely.

4. Follow instructions—All operating instructions must be

followed.

5. Cleaning—Unplug the power cord from the AC outlet

before cleaning the product. To clean the product, use the

supplied cleaning cloth or other soft cloth (e.g., cotton,

flannel). Do not use liquid cleaners or aerosol cleaners.

6. Attachments—Do not use attachments not recommended

by the manufacturer. Use of inadequate attachments can

result in accidents.

7. Water and moisture—Do not use the product near water,

such as bathtub, washbasin, kitchen sink and laundry tub,

swimming pool and in a wet basement.

8. Stand—Do not place the product on an unstable cart,

stand, tripod or table. Placing the product on an unstable

base can cause the product to fall, resulting in serious

personal injuries as well as damage to the product. Use

only a cart, stand, tripod, bracket or table recommended by

the manufacturer or sold with the product. When mounting

the product on a wall, be sure to follow the manufacturer’s

instructions. Use only the mounting hardware

recommended by the manufacturer.

9. When relocating the product placed on a cart, it must be

moved with utmost care. Sudden stops, excessive force

and uneven floor surface can cause the product to fall from

the cart.

10. Ventilation—The vents and other openings in the cabinet

are designed for ventilation. Do not cover or block these

vents and openings since insufficient ventilation can cause

overheating and/or shorten the life of the product. Do not

place the product on a bed, sofa, rug or other similar

surface, since they can block ventilation openings. This

product is not designed for built-in installation; do not

place the product in an enclosed place such as a bookcase

or rack, unless proper ventilation is provided or the

manufacturer’s instructions are followed.

11. Power source—This product must operate on a power

source specified on the specification label. If you are not

sure of the type of power supply used in your home, consult

your dealer or local power company.

12. Power cord protection—The power cords must be routed

properly to prevent people from stepping on them or

objects from resting on them. Check the cords at the plugs

and product.

13. The plasma Display used in this product is made of glass.

Therefore, it can break when the product is dropped or

applied with impact. Be careful not to be injured by broken

glass pieces in case the plasma Display breaks.

14. Overloading—Do not overload AC outlets or extension

cords. Overloading can cause fire or electric shock.

15. Entering of objects and liquids—Never insert an object into

the product through vents or openings. High voltage flows

in the product, and inserting an object can cause electric

shock and/or short internal parts. For the same reason, do

not spill water or liquid on the product.

16. Servicing—Do not attempt to service the product yourself.

Removing covers can expose you to high voltage and other

dangerous conditions. Request a qualified service person

to perform servicing.

17. Repair—If any of the following conditions occurs, unplug

the power cord from the AC outlet, and request a qualified

service person to perform repairs.

a. When the power cord or plug is damaged.

b. When a liquid was spilled on the product or when

objects have fallen into the product.

c. When the product has been exposed to rain or water.

d. When the product has been dropped or damaged.

e. When the product displays an abnormal condition. Any

noticeable abnormality in the product indicates that the

product needs servicing.

18. Replacement parts—In case the product needs

replacement parts, make sure that the service person uses

replacement parts specified by the manufacturer, or those

with the same characteristics and performance as the

original parts. Use of unauthorized parts can result in fire,

electric shock and/or other danger.

19. Safety checks—Upon completion of service or repair work,

request the service technician to perform safety checks to

ensure that the product is in proper operating condition.

20. Wall or ceiling mounting—When mounting the product on

a wall or ceiling, be sure to install the product according to

the method recommended by the manufacturer.

21. Heat sources—Keep the product away from heat sources

such as radiators, heaters, stoves and other heat-

generating products (including amplifiers).

22. Unplug the power cord from the AC outlet before installing

the speakers (for PDP-6072HD/PDP-5072HD/PDP-

6071HD/PDP-5071HD/PDP-6070HD/PDP-5070HD only).

23. Never expose the screen of the Plasma Display to a strong

impact, for example, by hitting it. The screen may be

broken, resulting in fire or personal injury.

24. Do not expose the Plasma Display to direct sunlight for a

long period of time. The optical characteristics of the front

protection panel changes, resulting in discoloration or

warp.

25. The Plasma Display weighs about 51.5 kg (113.6 lbs.) for the

PDP-6072HD/PDP-6071HD/PDP-6070HD, about 41.7 kg

(92 lbs.) for the PDP-5072HD/PDP-5071HD/PDP-5070HD

(including the stand and speaker) and about 31.5 kg (69.5

lbs.) for the PDP-4272HD/PDP-4271HD/PDP-4270HD

(including the stand). Because it has small depth and is

unstable, unpack, carry, and install the product with one

more person at least and use the handles.

PDP6070HD.book Page 10 Friday, May 19, 2006 5:01 PM

11

En

Safety Precautions

02

English

Installation Precautions

Observe the following precautions when installing with any

items such as the optional bracket.

When using the optional brackets or equivalent

items

• Ask your dealer to perform the installation.

• Be sure to use the supplied bolts.

• For details, see the instruction manual that comes with the

optional bracket (or equivalent items).

When using other items

• Consult your dealer.

• The following six mounting holes (four holes for the PDP-

6072HD/PDP-6071HD/PDP-6070HD) can be used for the

installation:

Rear view (PDP-6072HD/PDP-6071HD/PDP-6070HD)

Rear view (PDP-5072HD/PDP-5071HD/PDP-5070HD)

Rear view (PDP-4272HD/PDP-4271HD/PDP-4270HD)

Side view

CAUTION

• Be sure to use four or more mounting holes symmetrical to

the vertical and horizontal median lines.

• Use M8 screws, which go 12 mm to 18 mm (1/2 inches to

11/16 inches) in depth from the mounting surface of the

Plasma Display. See the side view above.

• Be careful not to block the ventilation opening at the rear of

the Plasma Display.

• Be sure to install the Plasma Display on a flat surface

because it contains glass.

• The screw holes other than the above are to be used only for

the specified products. Never use them for mounting non-

specified products.

NOTE

• It is strongly recommended to use the optional PIONEER

mounting products.

• PIONEER shall not be liable for any personal injury or

product damage that results from the use of mounting items

other than the optional PIONEER products.

Mounting

hole

Mounting

hole

Median line

Median

line

Mounting

hole

Mounting

hole

Median line

Median

line

Mounting hole

Median line

Mounting

hole

Median

line

Mounting surface

Plasma

Display

Mounting

bracket (or

equivalent item)

M8 screw

12 mm to 18 mm

(1/2 inches to 11/16 inches)

PDP6070HD.book Page 11 Friday, May 19, 2006 5:01 PM

12

En

Supplied Accessories

03

Supplied Accessories

* Buttons used for only basic operations are provided on the simplified remote control unit. You can use it as

necessary.

Power cord (2 m/6.6 feet)

Warranty card

Bead band

×

3

Cleaning cloth

AA size battery x 2

(Alkaline battery for

remote control unit)

Remote control unit

Operating instructions

G-LINK cable (3 m/9.8 feet)

Simplified remote control unit*

(for PDP-6071HD/PDP-5071HD/

PDP-4271HD only)

AAA size battery x 2

(Manganese battery for simplified

remote control unit)

(for PDP-6071HD/PDP-5071HD/

PDP-4271HD only)

Hexagonal wrench x 1

(Diagonal size: 6 mm)

(except 60-inch models)

Speed clamp

×

3

Speaker accessories

(for PDP-5072HD/PDP-5071HD/PDP-5070HD only)

Speaker Cable

×

2

Speaker Mounting Screw

(M5

×

10 mm: Black) x 9

Speaker Mounting Fittings

Bracket for Right Side Bracket for Center Bracket for Left Side

Ferrite core

Terminal position sheet

(for use when mounting the Plasma Display on the wall)

(PDP-6072HD/PDP-6071HD/PDP-6070HD only)

03_Supplied.fm Page 12 Thursday, May 25, 2006 3:04 PM

13

En

Part Names

04

English

Part Names

Plasma Display

1 a

POWER

button

(See page 32.)

2

POWER ON indicator

(See page 32.)

3

STANDBY indicator

(See page 32.)

4

REC TIMER indicator

5

Remote control sensor

(Side view)

6 STANDBY/ON

button

7INPUT

button (

ENTER

button*)

8 VOLUME UP/DOWN

buttons (

UP/DOWN

buttons*)

9 CHANNEL UP/DOWN

buttons (

LEFT/

RIGHT

buttons*)

10 TV GUIDE

button*

11

USB port

12

INPUT 4 terminals (COMPONENT VIDEO: Y,

C

B

/P

B

, C

R

/P

R

)

13

INPUT 4 terminal (VIDEO)

14

INPUT 4 terminals (AUDIO)

15

Stand: PDK-TS15 for the PDP-6072HD

PDK-TS15U for the PDP-6071HD/

PDP-6070HD

16

Speaker: PDP-S41

For details, refer to the operation manual that

came with the stand or speaker.

The buttons with asterisks (*) can operate the TV Guide On

Screen™ system.

ON REC TIMERSTANDBYPOWER

5

6

8

9

10

7

11

13

12

14

ON STANDBY REC TIMERPOWER

1

3

2

4

15 16

Front/side view

(PDP-6072HD/PDP-6071HD/PDP-6070HD)

PDP6070HD.book Page 13 Friday, May 19, 2006 5:01 PM

14

En

Part Names

04

1 a

POWER

button

(See page 32.)

2

POWER ON indicator

(See page 32.)

3

STANDBY indicator

(See page 32.)

4

REC TIMER indicator

5

Remote control sensor

(Side view)

6 STANDBY/ON

button

7INPUT

button (

ENTER

button*)

8 VOLUME UP/DOWN

buttons (

UP/DOWN

buttons*)

9 CHANNEL UP/DOWN

buttons (

LEFT/

RIGHT

buttons*)

10 TV GUIDE

button*

11

USB port

12

INPUT 4 terminals (COMPONENT VIDEO: Y,

C

B

/P

B

, C

R

/P

R

)

13

INPUT 4 terminal (VIDEO)

14

INPUT 4 terminals (AUDIO)

The buttons with asterisks (*) can operate the TV Guide On

Screen™ system.

REC TIMER

54

6

8

9

10

7

11

13

12

14

ON STANDBYPOWER

1

3

2

Front/side view

(PDP-5072HD/PDP-5071HD/PDP-5070HD)

PDP6070HD.book Page 14 Friday, May 19, 2006 5:01 PM

15

En

Part Names

04

English

1 a

POWER

button

(See page 32.)

2

POWER ON indicator

(See page 32.)

3

STANDBY indicator

(See page 32.)

4

REC TIMER indicator

5

Remote control sensor

(Side view)

6 STANDBY/ON

button

7INPUT

button (

ENTER

button*)

8 VOLUME UP/DOWN

buttons (

UP/DOWN

buttons*)

9 CHANNEL UP/DOWN

buttons (

LEFT/

RIGHT

buttons*)

10 TV GUIDE

button*

11

USB port

12

INPUT 4 terminals (COMPONENT VIDEO: Y,

C

B

/P

B

, C

R

/P

R

)

13

INPUT 4 terminal (VIDEO)

14

INPUT 4 terminals (AUDIO)

The buttons with asterisks (*) can operate the TV Guide On

Screen™ system.

6

8

9

10

7

11

13

12

14

5

1

REC TIMERON STANDBY

POWER

4

3

2

Front/side view

Viewed from below of the display

(PDP-4272HD/PDP-4271HD/PDP-4270HD)

Viewed from the front side of the display

PDP6070HD.book Page 15 Friday, May 19, 2006 5:01 PM

16

En

Part Names

04

1

PC INPUT terminal (ANALOG RGB)

2

CableCARD™ slot

3

ANT/CABLE A IN terminal

4

ANT B IN terminal

5

AC IN terminal

6

HDMI terminals (INPUT 5/INPUT 6)

7

RS-232C terminal (used for factory setup)

8

DIGITAL OUT terminal (OPTICAL)

9

G-LINK terminal

10

INPUT 5 terminals (AUDIO)

11

INPUT 6 terminals (AUDIO)

12

SUB WOOFER terminal

13

INPUT 3 terminals (AUDIO)

14

INPUT 3 terminals (COMPONENT VIDEO: Y,

C

B

/P

B

, C

R

/P

R

)

15

INPUT 2 terminals (COMPONENT VIDEO: Y,

C

B

/P

B

, C

R

/P

R

)

16

INPUT 2 terminal (VIDEO)

17

INPUT 2 terminal (S-VIDEO)

18

INPUT 2 terminals (AUDIO)

19

INPUT 1 terminals (AUDIO)

20

INPUT 1 terminal (S-VIDEO)

21

INPUT 1 terminal (VIDEO)

22

MONITOR OUT terminal (VIDEO)

23

MONITOR OUT terminals (AUDIO)

24

PC INPUT terminal (AUDIO)

25

CONTROL OUT terminal

26

SPEAKER (R/L) terminals

27

Stand: PDK-TS15 for the PDP-6072HD

PDK-TS15U for the PDP-6071HD/

PDP-6070HD

28

Speaker: PDP-S41

For details, refer to the operation manual that

came with the stand or speaker.

1 2

3

76 8

9

25

26

24

15

12

13

10

11

14

16

20

17 21

22

18 1923

4

5

28

27

Rear view

(Terminals located on the upper

edge of the compartment)

(PDP-6072HD/PDP-6071HD/PDP-6070HD)

PDP6070HD.book Page 16 Friday, May 19, 2006 5:01 PM

17

En

Part Names

04

English

1

PC INPUT terminal (ANALOG RGB)

2

CableCARD™ slot

3

ANT/CABLE A IN terminal

4

ANT B IN terminal

5

AC IN terminal

6

HDMI terminals (INPUT 5/INPUT 6)

7

RS-232C terminal (used for factory setup)

8

DIGITAL OUT terminal (OPTICAL)

9

G-LINK terminal

10

INPUT 5 terminals (AUDIO)

11

INPUT 6 terminals (AUDIO)

12

SUB WOOFER terminal

13

INPUT 3 terminals (AUDIO)

14

INPUT 3 terminals (COMPONENT VIDEO: Y,

C

B

/P

B

, C

R

/P

R

)

15

INPUT 2 terminals (COMPONENT VIDEO: Y,

C

B

/P

B

, C

R

/P

R

)

16

INPUT 2 terminal (VIDEO)

17

INPUT 2 terminal (S-VIDEO)

18

INPUT 2 terminals (AUDIO)

19

INPUT 1 terminals (AUDIO)

20

INPUT 1 terminal (S-VIDEO)

21

INPUT 1 terminal (VIDEO)

22

MONITOR OUT terminal (VIDEO)

23

MONITOR OUT terminals (AUDIO)

24

PC INPUT terminal (AUDIO)

25

CONTROL OUT terminal

26

SPEAKER (R/L) terminals

27

SPEAKER (R) terminal (Speaker side)

28

SPEAKER (L) terminal (Speaker side)

1 2

3

76 8

9

25

26

24

15

12

13

10

11

14

16

20

17 21

22

18 1923

4

5

27

28

Rear view

(Terminals located on the upper

edge of the compartment)

(PDP-5072HD/PDP-5071HD/PDP-5070HD)

PDP6070HD.book Page 17 Friday, May 19, 2006 5:01 PM

18

En

Part Names

04

1

PC INPUT terminal (ANALOG RGB)

2

CableCARD™ slot

3

ANT/CABLE A IN terminal

4

ANT B IN terminal

5

AC IN terminal

6

HDMI terminals (INPUT 5/INPUT 6)

7

RS-232C terminal (used for factory setup)

8

DIGITAL OUT terminal (OPTICAL)

9

G-LINK terminal

10

INPUT 5 terminals (AUDIO)

11

INPUT 6 terminals (AUDIO)

12

SUB WOOFER terminal

13

INPUT 3 terminals (AUDIO)

14

INPUT 3 terminals (COMPONENT VIDEO: Y,

C

B

/P

B

, C

R

/P

R

)

15

INPUT 2 terminals (COMPONENT VIDEO: Y,

C

B

/P

B

, C

R

/P

R

)

16

INPUT 2 terminal (VIDEO)

17

INPUT 2 terminal (S-VIDEO)

18

INPUT 2 terminals (AUDIO)

19

INPUT 1 terminals (AUDIO)

20

INPUT 1 terminal (S-VIDEO)

21

INPUT 1 terminal (VIDEO)

22

MONITOR OUT terminal (VIDEO)

23

MONITOR OUT terminals (AUDIO)

24

PC INPUT terminal (AUDIO)

25

CONTROL OUT terminal

1 2

3

76 8

9

25

24

15

12

13

10

11

14

16

20

17 21

22

18 1923

4

5

Rear view

(Terminals located on the upper

edge of the compartment)

(PDP-4272HD/PDP-4271HD/PDP-4270HD)

PDP6070HD.book Page 18 Friday, May 19, 2006 5:01 PM

19

En

Part Names

04

English

Remote control unit

This section describes the functions of the buttons available

when the mode switch has been set to TV. For the buttons for

controlling other equipment, see “Using the remote control

unit to control other devices” starting from page 87.

Simplified remote control unit

(PDP-6071HD/PDP-5071HD/PDP-4271HD only)

1TV

a

:

Turns on the power to the Plasma Display System or

places it into standby mode.

2

Transmission confirmation LED

3 INPUT

: Selects an input source of the Plasma Display

System. (INPUT 1, INPUT 2, INPUT 3, INPUT 4, INPUT 5,

INPUT 6 and PC) (With the simplified remote control unit,

INPUT

toggles between ANT-A, ANT-B, INPUT 1, INPUT 2,

INPUT 3, INPUT 4, INPUT 5, INPUT 6 and PC.)

4 SCREEN SIZE

: Selects the screen size.

5 SLEEP

: Sets the sleep timer.

6INFO

: Displays a channel banner when a TV program is being

watched.

When the TV Guide On Screen™ system is in operation,

displays information about the currently highlighted channel

(if available).

7HOME MENU

: Displays the Home Menu screen.

8 DAY +/–

: Jumps to the next or previous day of program

listings in the TV Guide On Screen™ Listing service.

9

///: Selects a desired item on the menu screen.

10 REC

: When using the TV Guide On Screen™ System, starts

recording with a connected VCR.

11 FAVORITE CH (A, B, C, D)

:

Selects any of the four preset channels. See page 49 for

details to set the FAVORITE CH.

While watching, you can toggle the set channels by pressing

A

,

B

,

C

and

D

.

12 0 – 9

: Selects the channel.

13 •(dot)

: Enters a dot.

14 CH +/–

: Selects the channel.

15 SPLIT

: Switches the screen mode among 2-screen, picture-in-

picture, and single-screen.

16 FREEZE

: Freezes a frame from a moving image. Press again

to cancel the function.

17 MTS

: Selects MTS/SAP or language depending on the

program being watched.

18 ANT

: Selects the antenna (A, B). See page 29 for details.

19 AV SELECTION

: Selects audio and video settings.

(AV mode:

STANDARD, DYNAMIC, MOVIE, GAME, USER. PC mode:

STANDARD, USER.)

20 DISPLAY

: Displays the channel information.

21 TV GUIDE

: Displays the TV Guide On Screen™ system.

22 ENTER

: Executes a command.

23 PAGE +/–

(for the TV Guide On Screen™ system): Scrolls the

program listing screen vertically.

24 RETURN

: Returns to the previous menu screen.

25 MENU

: Displays a panel menu in the TV Guide On Screen™

system.

26 CH ENTER

: Executes a channel number.

27 CH RETURN

: Returns to the previous channel. This button is

disabled while the TV Guide On Screen™ system is displayed.

28 VOL +/–

: Sets the volume.

29 M

MUTING

: Mutes the sound.

30 SHIFT

: Moves the location of the small screen when in the

picture-in-picture mode.

31 SWAP

: Switches between the two screens when in the 2-

screen or picture-in-picture mode.

Luminous remote control buttons (main unit only)

All buttons on the main remote control unit are luminous and

gather and store light. This enables quick access to the

desired function when performing operations in dark places.

NOTE

• When using the remote control unit, point it at the Plasma

Display.

• See pages 81 to 90 for operating buttons not listed on this

page.

1

10

11

13

12

14

22

23

24

5

3

4

18

19

20

21

7

8

9

25

15

17

16

27

26

29

28

31

30

2

6

Mode switch

(with “TV” selected)

14

28

12

13

27

29

26

22

20

19

4

3

1

PDP6070HD.book Page 19 Friday, May 19, 2006 5:01 PM

20

En

Preparation

05

Preparation

Installing the Plasma Display

Location

• Avoid direct sunlight. Maintain adequate ventilation.

• Because the Plasma Display is heavy, be sure to have

someone help you when moving it.

NOTE

• Allow enough space around the upper and back parts when

installing to ensure adequate ventilation of the rear of the

unit.

Moving the Plasma Display

(PDP-6072HD/PDP-6071HD/PDP-6070HD)

NOTE

• Do not hold by the speaker.

• When moving the Plasma Display, make sure to remove the

speaker first. Do not hold by the speaker mounting fittings.

(PDP-5072HD/PDP-5071HD/PDP-5070HD)

NOTE

• Do not hold by the speaker.

• When moving the Plasma Display, make sure to remove the

speaker first. Do not hold by the speaker mounting fittings.

(PDP-4272HD/PDP-4271HD/PDP-4270HD)

CAUTION

When installing on a rack, etc., hold the Plasma Display.

COMPONENT

@@@@@

VIDEO

AUDIO

Y

L

R

C

B

/ P

B

C

R

/ P

R

Over 50 cm

(19 11/16 inches)

Over

10 cm

(3 15/16

inches)

Stand: PDK-TS15 for the

PDP-6072HD

PDK-TS15U for the

PDP-6071HD/PDP-

6070HD

Speaker: PDP-S41

For details, refer to the operation

manual that came with the stand

or speaker.

PDP6070HD.book Page 20 Friday, May 19, 2006 5:01 PM

La page charge ...

Pioneer PDP-5072 Manuel utilisateur

Pioneer PDP-5072 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents