Sony CDP-XB720 Manuel utilisateur

Marque: Sony

Modèle: CDP-XB720

Catégorie: Lecteur CD

Taper: Manuel utilisateur

3-866-364-14 (1)

Operating Instructions

Mode d’emploi

Manual de instrucciones

CDP-XB930

CDP-XB930E

CDP-XB630

 1999 by Sony Corporation

Compact Disc

Player

Precautions

On safety

• Caution — The use of optical

instruments with this product will

increase eye hazard.

• Should any solid object or liquid fall

into the cabinet, unplug the player and

have it checked by qualified personnel

before operating it any further.

On power sources

• Before operating the player, check that

the operating voltage of the player is

identical with your local power

supply. The operating voltage is

indicated on the nameplate at the rear

of the player.

• The player is not disconnected from

the AC power source (mains) as long

as it is connected to the wall outlet,

even if the player itself has been

turned off.

• If you are not going to use the player

for a long time, be sure to disconnect

the player from the wall outlet. To

disconnect the AC power cord (mains

lead), grasp the plug itself; never pull

the cord.

• AC power cord must be changed only

at the qualified service shop.

On placement

• Place the player in a location with

adequate ventilation to prevent heat

build-up in the player.

• Do not place the player on a soft

surface such as a rug that might block

the ventilation holes on the bottom.

• Do not place the player in a location

near heat sources, or in a place subject

to direct sunlight, excessive dust or

mechanical shock.

On using the stabilizer (only for

CDP-XB930 and CDP-XB930E)

• Be sure to use the supplied stabilizer.

If you use any other stabilizer, you

may damage the player.

WARNING

To prevent fire or shock

hazard, do not expose the unit

to rain or moisture.

To avoid electrical shock, do

not open the cabinet. Refer

servicing to qualified

personnel only.

The laser component in this product

is capable of emitting radiation

exceeding the limit for Class 1.

This appliance is classified as a CLASS 1

LASER product. The CLASS 1 LASER

PRODUCT MARKING is located on the

rear exterior.

On operation

• If the player is brought directly from a

cold to a warm location, or is placed in

a very damp room, moisture may

condense on the lenses inside the

player. Should this occur, the player

may not operate properly. In this case,

remove the disc and leave the player

turned on for about an hour until the

moisture evaporates.

On adjusting volume

• Do not turn up the volume while

listening to a portion with very low

level inputs or no audio signals. If you

do, the speakers may be damaged

when a peak level portion is played.

On cleaning

• Clean the cabinet, panel and controls

with a soft cloth slightly moistened

with a mild detergent solution. Do not

use any type of abrasive pad, scouring

powder or solvent such as alcohol or

benzine.

On transportation

• Be sure to remove the CD and the

stabilizer.

If you have any questions or

problems concerning your player,

please consult your nearest Sony

dealer.

Don’t throw a battery,

dispose it as the

injurious wastes.

TABLE OF CONTENTS

Welcome!

Thank you for purchasing the Sony

Compact Disc Player. Before operating

the unit, please read this manual

thoroughly and retain it for future

reference.

About This Manual

The instructions in this manual are for

models CDP-XB930, CDP-XB930E,

and CDP-XB630. The CDP-XB930 is the

model used for illustration purposes.

Any difference in operation is clearly

indicated in the text, for example,

“CDP-XB930 only.”

Conventions

• Instructions in this manual describe

the controls on the player.

You can also use the controls on the

remote if they have the same or

similar names as those on the player.

• The following icons are used in this

manual:

Indicates that you can do the

task using the remote.

Indicates hints and tips for

making the task easier.

Getting Started

Unpacking ........................................................................................................ 4

Hooking Up the System ................................................................................. 4

Playing a CD ........................................................................................................ 6

Playing CDs

Using the Display ........................................................................................... 8

Locating a Specific Track or a Particular Point in a Track ...................... 10

Customising the Sound of Your Music (Digital Filter Function) (only for

CDP-XB930 and CDP-XB930E) ................................................................... 11

Playing Tracks Repeatedly .......................................................................... 12

Playing in Random Order (Shuffle Play) .................................................. 13

Creating Your Own Programme (Programme Play) ............................... 13

Recording From CDs

Recording Your Own Programme ............................................................. 15

Recording a CD by Specifying Tape Length (Time Edit/Just Edit) ...... 16

Fading In or Out............................................................................................ 17

Useful Tips for Recording ........................................................................... 18

Additional Information

Notes on CDs ................................................................................................. 19

Troubleshooting ............................................................................................ 19

Specifications ................................................................................................. 20

Index

Index ............................................................................................................... 21

Getting Started

Unpacking

Check that you received the following items:

• Audio connecting cord (1)

• Remote commander (remote) (1)

• R6 (size AA) batteries (2)

• Stabilizer (1) (only for CDP-XB930 and CDP-XB930E)

Inserting batteries into the remote

You can control the player using the supplied remote.

Insert two R6 (size AA) batteries by matching the +

and – on the batteries to the diagram inside the battery

compartment.

Insert the negative (–) end first, then push in and down

until the positive (+) end clicks into the position.

When using the remote, point it at the remote sensor g

on the player.

Hooking Up the System

Overview

This section describes how to hook up the CD player to

an amplifier. Be sure to turn off the power of each

component before making the connections.

CD player

Line output

(R)

Line output

(L)

Audio input

(L)

Audio input

(R)

Amplifier

: Signal flow

To mains

When to replace batteries

With normal use, the batteries should last for about six

months. When the remote no longer operates the player,

replace all the batteries with new ones.

Notes

• Do not leave the remote near an extremely hot or humid

place.

• Do not drop any foreign object into the remote casing,

particularly when replacing the batteries.

• Do not expose the remote sensor to direct sunlight or

lighting apparatuses. Doing so may cause a malfunction.

• If you don’t use the remote for an extended period of time,

remove the batteries to avoid possible damage from battery

leakage and corrosion.

Getting Started

What cords will I need?

pWhen making analog hookups

• Audio cord (supplied) (1)

White

(L)

Red

(R)

White

(L)

Red

(R)

pWhen making digital hookups

• Optical cable POC-15 (not supplied)

• Coaxial cable (not supplied) (only for CDP-XB930 and

CDP-XB930E)

Getting Started

You can adjust the output level to the amplifier

Press LINE OUT LEVEL +/– on the remote. You can

reduce the output level up to –20 dB.

When you reduce the output level, “FADE” appears in

the display.

When you turn off the player, the output level

automatically returns to the maximum level.

Note

If you press the LINE OUT LEVEL +/– buttons on the remote

while recording, the recording level will change even when it

is preset on the tape deck, etc.

pWhen making digital hookups

You can avoid deterioration of the signal during

transmission, since the music signal output through

the digital output connectors retains digital form.

You can connect a digital component such as a

digital amplifier, D/A converter, DAT or MD. When

you connect a DAT or MD, you can make digital

recordings from CDs.

Note that you cannot use the following functions

when making this connection:

• Fading in or out (see page 17)

• Time Fade (see page 17)

• Adjusting the output level using the LINE OUT

LEVEL +/– buttons on the remote (see above)

AmplifierCD player

Hookups

pWhen making analog hookups

When connecting an audio cord, be sure to match the

colour-coded cord to the appropriate jacks on the

components: Red (right) to Red and White (left) to

White. Be sure to make connections firmly to avoid

hum and noise.

Digital component

CD player

• If you have a digital component with an optical digital

input connector

Connect the component via the DIGITAL OUT (OPTICAL)

connector using the optical cable (not supplied). Take off

the cap and plug in the optical cable.

Note

When you connect via the DIGITAL OUT connector, noise

may occur when you play CD software other than music, such

as a CD-ROM.

If you have a Sony component with the CONTROL

A1 (or CONTROL A1) jack

Connect the component via the CONTROL A1 jack.

You can simplify the operation of audio systems

composed of separate Sony components. For details, refer

to the supplementary “CONTROL-A1 Control System”

instructions.

Connecting the mains lead

Connect the mains lead to a wall outlet.

Removing the warning from the disc tray

(CDP-XB930 and CDP-XB930E only)

The warning, “Do not touch the lens inside,” is put

inside the disc tray at the factory.

Before using the player, you must remove this

warning. Turn on the player, and press

§ OPEN/CLOSE, and remove the warning.

Where do I go next?

Now you’re ready to use your player.

If you aren’t familiar with how to play CDs, go to the section

“Playing a CD” on page 6.

Then, go to the following sections for other operations.

LINE OUT

INPUT

DIGITAL OUT

OPTICALCOAXIAL

DIGITAL IN

OPTICAL

DIGITAL OUT

OPTICALCOAXIAL

DIGITAL IN

COAXIAL

Digital component

CD player

• If you have a digital component with a coaxial digital

input connector (CDP-XB930 and CDP-XB930E only)

Connect the component via the DIGITAL OUT (COAXIAL)

connector using the coaxial cable (not supplied).

Basic Operations

Turn on the amplifier and select the CD player position.

Press U to turn on the player.

Press § OPEN/CLOSE, and place a CD on the tray.

Playing a CD

• See pages 4 – 5 for the hookup

information.

If you turn on the player with

a CD in the tray

You can start playing

automatically from the

beginning of the CD. If you

connect a commercially

available timer, you can start

playing the CD at any time

you want.

If “– NO STABI –” appears in

the display (only for

CDP-XB930 and CDP-XB930E)

Place the supplied stabilizer

on the CD.

If you do not, this indication

appears.

Note

In Step 3, do not place two or

more CDs at the same time.

If you do so, you may damage

the discs and/or the player.

234

Connect the

headphones.*

Adjust the

headphones volume.**

With the label side up

Place the supplied stabilizer on the CD

with the smaller hole side facing up.

* Only for CDP-XB930 and CDP-XB630

** Only for CDP-XB930

*** Only for CDP-XB930 and CDP-XB930E

Press ·.

The disc tray closes and the player plays all the tracks once

(Continuous Play).

Adjust the volume on the amplifier.

• CDP-XB930 and CDP-XB930E

• CDP-XB630

PHONES

PHONE LEVEL

FILTER

PLAY MODE REPEAT FADER TIME/TEXT

LANGUAGE

OPEN/CLOSE

STD

MIN MAX

PEAK

AUTO

SPACE

MUSIC

SCAN

EDIT/

TIME FADE

CHECK CLEAR

PUSH ENTER

AMS

With the label side up

Select the desired

digital filter type.***

Basic Operations

To stop playback

Press p.

When you want to

Pause

Resume play after pause

Go to the next track

Go back to the preceding track

Stop play and remove the CD

You need to

Press P

Press P or ·

Turn ≠ AMS ± clockwise

Turn ≠ AMS ± counterclockwise

Press § OPEN/CLOSE

§ OPEN/CLOSE

≠ AMS ±

PHONES

PHONE LEVEL

FILTER

PLAY MODE REPEAT FADER TIME/TEXT

LANGUAGE

OPEN/CLOSE

STD

MIN MAX

PEAK

AUTO

SPACE

MUSIC

SCAN

EDIT/

TIME FADE

CHECK CLEAR

PUSH ENTER

AMS

Playing CDs

While in Shuffle Play mode (“SHUFFLE” appears in

the display; see page 13), a one-second access time

blank is added between each track. This increase is

automatically added to the total playing time in the

display.

The information also appears when you press

§ OPEN/CLOSE to close the disc tray.

Using the Display

You can check information about the disc using the

display.

Playing CDs

TIME/TEXT

Checking the total number and playing

time of the tracks

Press TIME/TEXT (or TIME on the remote) before you

start playing.

The display shows the total number of tracks, total

playing time and music calendar.

Music calendar

Total playing time

Total number of

tracks

If the remaining time exceeds 100 minutes in Programme Play

mode or when the disc has more than 24 tracks, “– – . ––”

appears instead of the remaining time.

Press

If the track number exceeds 24, “– – . ––” appears instead of the

remaining time.

Press

Playing time of the

current track

Remaining time on

the current track

Remaining time on

the disc

Display information while playing a disc

While playing a disc, the display shows the current

track number, index number, playing time and music

calendar.

LANGUAGE ≠ AMS ±

12345

678910

TRACK INDEX

MIN SEC

12345

678910

TRACK INDEX

MIN SEC

Music calendar

Playing time

Current track

number

Index number

Checking the remaining time

Each time you press TIME/TEXT (or TIME on the

remote) while playing a disc, the display changes as

shown in the chart below.

The track numbers in the music calendar disappear

after they are played.

DISPLAY ON/OFF

TIME

12345

678910

TRACK INDEX

MIN SEC

12345

678910

MIN SEC

12345

678910

TRACK INDEX

MIN SEC

Playing CDs

• While playing a disc

Press

12345

678910

TRACK

TEXTCD

12345

678910

TRACK INDEX

MIN SEC

TEXTCD

12345

678910

TRACK INDEX

MIN SEC

TEXTCD

12345

678910

MIN SEC

TEXTCD

Playing time of the

current disc

Track title

Remaining time on

the current track

Remaining time on

the disc

If the remaining time exceeds 100 minutes

in Programme Play mode or when the disc

has more than 24 tracks, “– – . ––” appears

instead of the remaining time.

If the track number exceeds 24,

“– – . ––” appears instead of the

remaining time.

Press

If a title or name has more than 12 characters, the first

12 characters will light up after the title or name scrolls

by in the display.

This information also appears

when the player locates the track.

Notes

• The display may not show all the characters depending on

the disc.

• This player can only display the disc titles, track titles and

artist names from CD TEXT discs. Other information cannot

be displayed.

Checking the information of CD TEXT discs

in other languages

You can change the displayed language if your CD

TEXT disc has multi language capacity. When the

player detects such a CD TEXT disc, “CD TEXT” and

“MULTI” appear in the display.

If the player cannot read the language memorised in a

CD TEXT disc, the display shows “<OTHER LANG>”

after the player detects the disc.

• Before you start playing

12345

678910

DISC

TEXTCD

12345

678910

ART.

TEXTCD

12345

678910

TRACK INDEX

MIN SEC

TEXTCD

Press

Total number of

tracks and total

playing time

Press

Artist name

Disc title

Checking the information of CD TEXT discs

CD TEXT discs have information, such as the disc titles

or artist names, memorised in a blank space on the

discs where, on normal discs, there is no information.

The display shows the CD TEXT information of the

disc so that you can check the current disc title, artist

name and track title. When the player detects CD TEXT

discs, the “CD TEXT” indication appears in the

display. If your CD TEXT disc has multi language

capacity, “CD TEXT” and “MULTI” indications appear

in the display. If you want to check the information in

another language, refer to “Checking the information

of CD TEXT discs in other languages” on page 9.

Each time you press TIME/TEXT (or TIME on the

remote), the display changes as shown in the chart

below.

(Continued)

Playing CDs

Locating a Specific Track or a

Particular Point in a Track

You can quickly locate any track while playing a disc

using the AMS (Automatic Music Sensor) on the player

or number buttons on the remote.

You can also locate a particular point in a track while

playing a disc.

0/)

≠ AMS ±

MUSIC SCAN

1 Before playing a CD TEXT disc, press

LANGUAGE.

“SELECT LANG” and the current operating

language appear in the display.

2 Turn ≠ AMS ± until the language you want

to select appears in the display.

3 Push ≠ AMS ± to select the language.

“READING TEXT” appears momentarily, then the

display shows the new selected language.

4 Press TIME/TEXT (or TIME on the remote)

repeatedly until the information you want to check

appears (see page 9).

Notes

• If your CD TEXT disc is not equipped with other languages,

“CAN’T SELECT” appears in the display when you press

the LANGUAGE button.

• If you press LANGUAGE while playing a CD TEXT disc,

the current operating language appears momentarily.

• The operating language you have selected remains until

you turn off the power.

Turning off indications in the display

Each time you press DISPLAY ON/OFF on the remote

while playing a disc, the display turns off and on

alternately.

Even when the display is turned off, the display turns

on if you pause or stop play. When you resume play,

the display turns off again.

Before you start playing, when you press DISPLAY

ON/OFF to turn off the display, “DISPLAY OFF”

appears, and when you press the button to turn on the

display, “DISPLAY ON” appears.

Number

buttons

>10

=/+

0/)

Playing CDs

When you directly locate a track numbered over 10

Press >10 first, then the corresponding number buttons.

To enter “0,” use button 10.

Example: To play track number 30

Press >10 first, then 3 and 10.

You can extend the playing time during Music Scan

Press MUSIC SCAN repeatedly until the playing time

you want (10, 20 or 30) appears in the display. Each time

you press the button, the playing time changes cyclically.

Note

If “– OVER –” appears in the display, the disc has reached the

end while you were pressing ). Press 0 or turn

≠ AMS ± counterclockwise to go back.

To locate

The next or

succeeding tracks

The current or

preceding tracks

A specific track

directly

By scanning each

track for 10 seconds

(Music Scan)

A point while

monitoring the sound

A point quickly by

observing the display

during pause

You need to

Turn ≠ AMS ± clockwise until

you find the track. When using the

remote, press + repeatedly until

you find the track.

Turn ≠ AMS ± counterclockwise

until you find the track. When using

the remote, press = repeatedly until

you find the track.

Turn ≠ AMS ± until you find the

track number you want. When using

the remote, press the number button of

the track.

Press MUSIC SCAN. When you find

the track you want, press · to start

playing the track.

Press ) (forward) or 0 (backward)

and hold down until you find the

point.

Press ) (forward) or 0 (backward)

and hold down until you find the

point. You will not hear the sound

during the operation.

Customising the Sound of Your

Music (Digital Filter Function)

(Only for CDP-XB930 and CDP-

XB930E)

By selecting the type of filter you want, you can adjust

the sound to match your system, your speakers, etc.

This player has four types of filters: “STD (Standard),”

“1,” “2” and “3.”

FILTER

Sound image

• wide ranging

• ample spatial representation

• clear

• smooth sound reproduction

• high clarity

• strength

• warm

• deep

Set the FILTER control to the digital filter type you

want. The display shows the digital filter type you

select.

If you change the type of digital filter during play, the

sound will be interrupted momentarily.

Notes

• The Digital Filter function primarily changes characteristics

outside the audible frequency. They cannot affect changes

within the audible frequency such as those provided by the

tone controls of the amplifier. Therefore, with certain

combinations of hardware and software, there may be no

noticeable effect after switching the filter.

• If you change the type of digital filter during Peak Search

(See page 18), the type of filter appears in the display when

Peak Search is finished.

Types of Digital Filter

STD (Standard)

Playing CDs

Repeating the current track (Repeat 1)

You can repeat only the current track in any play

mode.

While the track you want is being played, press

REPEAT repeatedly until “REPEAT 1” appears in the

display.

To cancel Repeat 1

Press REPEAT.

Repeating a Specific Portion (A˜B

Repeat)

You can play a specific portion in a track repeatedly.

This might be useful when you want to memorize

lyrics.

Note that you cannot repeat a portion extending to two

tracks.

1 While playing a disc, press A – B on the remote

when you find the starting point (point A) to be

played repeatedly.

“A-” of “REPEAT A-” flashes in the display.

2 When you reach the ending point (point B), press

A – B again.

“REPEAT A-B” appears. The player plays this

specific portion repeatedly.

To cancel A˜B Repeat

Press REPEAT.

Setting a new starting point

You can move the repeating portion ahead by

changing the starting point.

1 Press A – B while the player is repeating the

specific portion.

The ending point B becomes the new starting point

A. “A-” of “REPEAT A-” flashes in the display.

2 When you reach the ending point (point B), press

A – B again.

“REPEAT A-B” appears. The player repeats

between the new starting and ending points.

When you want to restart from the starting point A

Press · during A˜B Repeat.

REPEAT

Playing Tracks Repeatedly

You can play tracks repeatedly in any play mode.

Press REPEAT while playing a disc.

“REPEAT” appears in the display. The player repeats

the tracks as follows:

When the disc is played in

Continuous Play (page 6)

Shuffle Play (page 13)

Programme Play (page 13)

To cancel Repeat Play

Press REPEAT twice.

The player repeats

All the tracks

All the tracks in random order

The same programme

REPEAT

A – B

Playing CDs

Push ≠ AMS ± to select the track.

Playing in Random Order

(Shuffle Play)

You can have the player “shuffle” tracks and play in a

random order.

PLAY MODE

1 Press PLAY MODE repeatedly until “SHUFFLE”

appears in the display.

When using the remote, press SHUFFLE.

2 Press · to start Shuffle Play.

The

indication appears while the player is

“shuffling” the tracks.

To cancel Shuffle Play

Press PLAY MODE twice.

When using the remote, press CONTINUE.

You can start Shuffle Play while playing

Press PLAY MODE repeatedly until “SHUFFLE” appears

in the display. When using the remote, press SHUFFLE.

Shuffle Play starts from the current track.

SHUFFLE

TRACK STEP

MIN SEC

PROGRAM

Creating Your Own Programme

(Programme Play)

You can arrange the order of the tracks on a disc and

create your own programme. The programme can

contain up to 24 tracks.

CHECK CLEAR ≠ AMS ±

PLAY MODE

Creating a programme on the player

1 Press PLAY MODE repeatedly until “PROGRAM”

appears in the display before you start playing.

2 Turn ≠ AMS ± until the track number you

want appears in the display.

Track number being

programmed

Total playing time

Playing order

Last programmed track

Playing order

Programmed tracks

Total playing time

If you’ve made a mistake

Press CLEAR, then repeat Steps 2 and 3.

4 Repeat Steps 2 and 3 to programme the tracks in

the order you want.

5 Press · to start Programme Play.

TRACK STEP

MIN SEC

PROGRAM

TAPE A

Playing CDs

Creating a programme using the remote

1 Press PROGRAM before you start playing.

“PROGRAM” appears in the display.

2 Press the number buttons of the tracks you want to

programme in the order you want.

Example: To programme the tracks 2, 8 and 5.

Press the number buttons in the order

2, 8 and 5.

To select a track with a number over 10

Use >10 button (see page 11).

If you’ve made a mistake

Press CLEAR, then press the correct track number.

3 Press · to start Programme Play.

To cancel Programme Play

Press CONTINUE.

You can check the total playing time while

programming using the remote (Programme Edit)

To select a track, press = or + and check the total

playing time. Then press PROGRAM to confirm your

selection.

Notes

• The total playing time doesn’t appear in the display when it

exceeds 100 minutes.

• If you programme a track numbered over 24, “– – . ––”

appears instead of the total playing time.

•“PROGRAM FULL” appears in the display when you try to

add a track to a programme which already contains 24

tracks.

PROGRAM

CLEAR

Number buttons

CHECK

>10

To cancel Programme Play

Press PLAY MODE.

When tracks, which aren’t numerically consecutive on

the disc, are programmed consecutively (i.e. 1, 3, 5

etc.)

A one-second access time blank is added between the

tracks.

The programme remains until erased (see page 15) or

until you press §OPEN/CLOSE

The programme you have created remains even after the

Programme Play mode ends or you select another play

mode.

Notes

• The total playing time doesn’t appear in the display when it

exceeds 100 minutes.

• If you programme a track numbered over 24, “– – . ––”

appears instead of the total playing time.

•“PROGRAM FULL” appears in the display when you try to

add a track to a programme which already contains 24

tracks.

Recording From CDs

Recording Your Own

Programme

You can record the programme you’ve created on a

tape, DAT or MD. The programme can contain up to 24

tracks.

By inserting a pause during programming, you can

divide the programme into two for recording on both

sides of a tape.

≠ AMS ±

PLAY MODE

1 Create your programme (for side A when

recording on a tape) while checking the total

playing time indicated in the display.

Follow Steps 1 to 4 in “Creating a programme on

the player” on page 13 or Steps 1 and 2 in

“Creating a programme using the remote” on page

14.

“TAPE A” appears in the display.

2 When you record on both sides of the tape, press

P to insert a pause.

“P” and “TAPE B” appear in the display and the

playing time is reset to “0.00.”

When you record on one side of the tape or on a

DAT or MD, skip this step and go to Step 4.

A pause is counted as one track

You can programme up to 23 tracks when you insert a

pause.

3 Repeat Step 1 to create the programme for side B.

4 Start recording on the deck and then press · on

the player.

When you record on both sides of the tape, the player

pauses at the end of the programme for side A.

5 When you record on side B, reverse the tape and

press · or P on the player to resume playing.

To check and change your programme

See page 15.

“TAPE A” appears while checking the programme for

side A and “TAPE B” appears while checking the

programme for side B.

Recording From CDs

Checking the track order

You can check your programme before or after you

start playing.

Press CHECK.

Each time you press this button, the display shows the

track number in the programmed order. After the last

track in the programme, the display shows “– END –”

and returns to the original display. If you check the

order after you start playing, the display shows only

the remaining track numbers.

Changing the track order

You can change your programme before you start

playing.

Erase a track

Erase the last track in the

programme

Add tracks to the end of the

programme

Erase the whole programme

completely

You need to

Press CHECK until the track

you don’t want appears in

the display, then press

CLEAR

Press CLEAR. Each time you

press the button, the last

track will be cleared.

Turn ≠ AMS ± until

the track number you want

to add appears, then push

≠ AMS ±.

When using the remote,

press the number buttons of

the tracks to be added.

Hold down CLEAR until

“CLEAR” appears in the

display. Create a new

programme following the

programming procedure.

Playing CDs

(Continued)

Recording From CDs

1 Press EDIT/TIME FADE before you start playing

as follows:

• To select Time Edit, press the button until

“EDIT” appears and “A” of “TAPE A” flashes in

the display.

• To select Just Edit, press the button until

“JUST EDIT” appears and “A” of “TAPE A”

flashes in the display.

2 Press 0 or ) to specify the tape length.

Each time you press these buttons, the display

changes as shown below with the tape length of

one side .

n HALF ˜ C-46 23.00 ˜ C-54 27.00 ˜ C-60 30.00 N

n - -. - - ˜ C-90 45.00 ˜ C-74 37.00 N

Recording a CD by Specifying

Tape Length

(Time Edit/Just Edit)

You can have the player create a programme that will

fit the length of the tape. Select one of the following

options:

• Time Edit: automatically creates a programme,

keeping the original order of the disc. However,

when the remaining time becomes shorter than the

next succeeding track, the player automatically

programmes a track which is nearly equal to the

remaining time.

• Just Edit: automatically arranges the track order to fit

the tape length.

The programme may contain up to 24 tracks (a pause

inserted between tracks is counted as one track).

Note that tracks numbered over 24 cannot be

programmed in this feature.

EDIT/TIME FADE

0/)

When tracks, which aren’t numerically consecutive on

the disc, are programmed consecutively (i.e. 1, 3, 5

etc.)

A one-second access time blank is added between the

tracks.

When you select “HALF”

The player divides the total playing time of the disc in

half, keeping the original order (only in Time Edit).

Note that you cannot select “HALF” when the disc has

more than 24 tracks.

3 Press EDIT/TIME FADE to have the player create

the programme.

The music calendar shows the tracks to be

recorded. “B” of “TAPE B” flashes in the display.

4 When you record on both sides of the tape, press

EDIT/TIME FADE again.

The player inserts a pause, then creates the

programme for side B. The display shows the

programmed tracks.

When you record on one side of the tape or on a

DAT or MD, skip this step.

5 Start recording on the deck and then press · on

the player.

When you record on both sides of the tape, the

player pauses at the end of the programme for side

6 When you record on side B, reverse the tape and

press · or P on the player to resume playing.

To cancel Time Edit/Just Edit

Press PLAY MODE.

When using the remote, press CONTINUE.

You can specify the tape length freely in Step 2

You can set the tape length using ≠ AMS ±.

Example: When the tape length of one side is 30 minutes

and 15 seconds

1 To set the minutes, turn ≠ AMS ± until

“30” appears in the display, then push

≠ AMS ±.

2 To set the seconds, turn ≠ AMS ± until

“15” appears in the display, then push

≠ AMS ±.

When tracks, which aren’t numerically consecutive on

the disc, are programmed consecutively (i.e. 1, 3, 5

etc.)

A one-second access time blank is added between the

tracks.

To check and change your programme

See page 15.

Recording From CDs

Start play fading in

End play fading out

Press FADER

During pause. “FADE” flashes.

Then play fades in.

When you want to start fading out.

“FADE” flashes. Then play fades out

and the player pauses.

Fading in or out at the point you want

Fading In or Out

You can manually fade in or out to prevent tracks from

starting or ending abruptly.

Note that you cannot use this effect when you use the

DIGITAL OUT (OPTICAL/COAXIAL) connector.

FADER

Number buttons

EDIT/TIME

FADE

0/)

FADER

≠ AMS ±

Changing the fading time

You can change the fading time from 2 to 10 seconds

before fading in or out. If you don’t change it, fading

lasts for 5 seconds.

1 Before you start playing, press FADER.

2 Turn ≠ AMS ± until the time you want

appears in the display. When using the remote,

press the number buttons to specify the fading

time.

Notes

• The fading time is reset to 5 seconds when you turn off the

player.

• If you press FADER during Music Scan (page 11), fade out

time changes to 2 seconds.

Fading out at the specified time

(Time Fade)

You can have the player fade out automatically by

specifying the playing time. Once you set the time fade,

it works twice, that is, the play fades out at the end of

both sides of a tape.

1 Press EDIT/TIME FADE repeatedly before you

start playing until “T.FADE” and “TAPE A”

appear in the display.

2 Press 0 or ) to specify the playing time. Each

time you press these buttons, the display changes

as shown below with the tape length of one side.

When you select “HALF”

The player sets the playing time to a half of the total

playing time.

3 Press · to start playing.

At the specified time the play fades out and the

player pauses. “TAPE B” appears in the display.

4 To record on side B, reverse the tape and press ·

or P on the player to resume playing.

Again, the play fades out at the specified time.

Fading time lasts for 5 seconds. If you press FADER

during Music Scan (page 11), fade out time changes to

2 seconds.

n HALF ˜ C-46 23.00 ˜ C-54 27.00 ˜ C-60 30.00 N

n - -. - - ˜ C-90 45.00 ˜ C-74 37.00 N

Recording From CDs

AUTO SPACE

PEAK SEARCH

To cancel Time Fade

Press EDIT/TIME FADE.

You can freely specify the recording time

See “You can specify the tape length freely in Step 2” on

page 16.

You can change discs during Time Fade

If the play ends before the specified fade-out time, (for

example, when you record CD-singles on a tape) you can

change the disc. The specified fade-out time is counted

only during playing.

You can fade in to resume playing in Step 4

After you reverse the tape, press FADER.

Notes

• Time Fade will be cancelled if you press 0 or ) during

the operation.

•“HALF” does not appear when the disc has more than 24

tracks.

Adjusting the Recording Level (Peak Search)

The player locates the highest level among the tracks to

be recorded to let you adjust the recording level before

you start recording.

1 Before you start playing, press PEAK SEARCH.

“PEAK” flashes in the display and the player starts

scanning the disc searching for the highest peak

level.

After scanning all the tracks, the player repeats the

portion with the highest peak level.

2 Adjust the recording level on the deck.

3 Press p on the player to stop Peak Search.

“PEAK” disappears from the display.

Useful Tips for Recording

Using these functions makes recording CDs more

convenient.

Note

The portion with the highest level may differ every time you

try the adjustment on the same disc. The difference is,

however, so slight that you won’t find any problem in

adjusting the recording level precisely.

Inserting a blank space between tracks

(Auto Space)

When the space between tracks is too short for the

AMS function to work, you can insert a blank space of

3 seconds between each track while playing. This

enables easy location of tracks using the AMS function

of the deck .

Press AUTO SPACE.

“AUTO SPACE” appears in the display.

To cancel Auto Space

Press AUTO SPACE.

Note

If you use the Auto Space function when recording, for

example, a medley or symphony, the sound may be

interrupted where the track number changes. It happens

when the track numbers are assigned in the middle of the

piece.

Notes on CDs

On handling CDs

• To keep the disc clean, handle the disc by its edge. Do not

touch the surface.

• Do not stick paper or tape on the disc.

• Do not expose the disc to direct sunlight or heat sources

such as hot air ducts, nor leave it in a car parked in direct

sunlight as there can be considerable rise in temperature

inside the car.

• Do not use any commercially available stabilizer and/or

disc protector. If you do, the disc and the player may be

damaged.

• After playing, store the disc in its case.

On placing CDs on the disc tray

• Make sure the disc is positioned securely on the tray’s

spindle. If not, it may damage the player or the disc.

On cleaning

• Before playing, clean the disc with a cleaning cloth. Wipe

the disc from the centre out.

• Do not use solvents such as benzine, thinner,

commercially available cleaners or anti-static spray

intended for vinyl LPs.

Additional Information

Troubleshooting

If you experience any of the following difficulties while

using the player, use this troubleshooting guide to help

you remedy the problem. Should any problem persist,

consult your nearest Sony dealer.

There’s no sound.

/Check that the player is connected securely.

/Make sure you operate the amplifier correctly.

/Adjust the output level with LINE OUT

LEVEL +/– on the remote.

/When you use the headphones, adjust the

volume with PHONE LEVEL (only for

CDP-XB930).

The CD does not play.

/There’s no CD inside the player (“– NO DISC –”

appears). Insert a CD.

/There’s no stabilizer on the CD

(“– NO STABI –” appears). Place the stabilizer

on the CD (only for CDP-XB930 and

CDP-XB930E).

/Place the CD with the label side up on the disc

tray correctly.

/Clean the CD (see page 19).

/Moisture has condensed inside the player.

Remove the disc and leave the player turned on

for about an hour (see page 2).

The recording level has changed.

/The recording level changes if you press the

LINE OUT LEVEL +/– buttons on the remote

during recording.

The remote does not function.

/Remove the obstacles in the path of the remote

and the player.

/Point the remote at the remote sensor g on the

player.

/Replace all the batteries in the remote with new

ones if they are weak.

Specifications

Compact disc player

Laser Semiconductor laser (λ = 780 nm)

Emission duration: continuous

Laser output Max 44.6 µW*

* This output is the value measured at

a distance of 200 mm from the

objective lens surface on the Optical

Pick-up block with 7 mm aperture.

Frequency response 2 Hz to 20 kHz ± 0.5 dB

Signal-to-noise ratio CDP-XB930: More than 113 dB

CDP-XB630: More than 102 dB

Dynamic range CDP-XB930/XB930E: More than 99 dB

CDP-XB630: More than 98 dB

Harmonic distortion CDP-XB930/XB930E: Less than

0.0025%

CDP-XB630: Less than 0.0035%

Channel separation CDP-XB930: More than 105 dB

CDP-XB630: More than 100 dB

Outputs

LINE OUT

DIGITAL

OUT

(OPTICAL)

DIGITAL

OUT

(COAXIAL)

(only for CDP-XB930 and

CDP-XB930E)

PHONES

(only for CDP-XB930 and

CDP-XB630)

General

Power requirements 220 V – 230 V AC, 50/60 Hz

Power consumption CDP-XB930/XB930E: 15 W

CDP-XB630: 11 W

Dimensions (approx.) CDP-XB930/XB930E:

(w/h/d) 430 × 117 × 290 mm

(17 × 4 5/8 × 11 1/2 in.) incl. projecting

parts

CDP-XB630: 430 × 115 × 290 mm

(17 × 4 5/8 × 11 1/2 in.) incl. projecting

parts

Mass (approx.) CDP-XB930/XB930E: 6.0 kg

(15 lbs 10 oz)

CDP-XB630: 4.8 kg

(10 lbs 9 oz)

Supplied accessories

Audio cord (2 phono plugs – 2 phono plugs) (1)

Remote commander (remote) (1)

R6 (size AA) batteries (2)

Stabilizer (1) (only for CDP-XB930 and CDP-XB930E)

Design and specifications are subject to change without notice.

Jack

type

Phono

jacks

Optical

output

connector

Coaxial

output

connector

Stereo

phone

jack

Maximum

output

level

2 V

(at 50 kilohms)

–18 dBm

0.5 Vp-p

(at 75 ohms)

10 mW

Load

impedance

Over

50 kilohms

Wave length:

660 nm

75 ohms

32 ohms

Additional Information

La page charge ...

Sony CDP-XB720 Manuel utilisateur

Marque: Sony

Modèle: CDP-XB720

Catégorie: Lecteur CD

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Sony CDP-XB720 User manual
español: Sony CDP-XB720 Manual de usuario

Documents connexes

Autres documents

Philips CD 608 Manuel utilisateur