PROPOINT 9029372 Le manuel du propriétaire

Marque: PROPOINT

Modèle: 9029372

Catégorie: Outils électroportatifs

Taper: Le manuel du propriétaire

V1.0 9029372

Please read and understand all instructions before use. Retain this manual for future reference.

DECAL AND UNDERCOAT

REMOVAL KIT



This page is intentionally left blank.

SPECIFICATIONS

Wheel Diameter 4 in.

Spindle Size 11/32 in.

Air Inlet 1/4 in.

Pressure Range 90 PSI

Air Consumption @ 90 PSI 3.5 CFM

Min. Hose Size 3/8 in.

No Load Speed 4,000 RPM

Material Steel/aluminum/plastic

Tool Length 11-13/16 in.

INTRODUCTION

The Decal and Undercoat Removal Kit is ideal for removing decals,

paint, rust and corrosion from metal and plastic components.

SAFETY

WARNING! Read and understand all instructions before

using this tool. The operator must follow basic precautions

to reduce the risk of personal injury and/or damage to the

equipment.

HAZARD DEFINITIONS

Please familiarize yourself with the hazard notices found in this manual.

A notice is an alert that there is a possibility of property damage, injury

or death if certain instructions are not followed.

DANGER! This notice indicates an immediate and specific hazard that will

result in severe personal injury or death if the proper precautions

are not taken.

WARNING! This notice indicates a specific hazard or unsafe practice that could

result in a serious injury if the proper precautions are not taken.

CAUTION! This notice indicates a potentially hazardous situation that may

result in minor or moderate injury if proper practices are not taken.

NOTICE! This notice indicates that a specific hazard or unsafe practice will

result in equipment or property damage, but not personal injury.

V1.0 DECAL AND UNDERCOAT REMOVAL KIT 9029372

Page 3 Assistance available at www.princessauto.com or 1-800-665-8685

WORK AREA

1. Operate in a safe work environment. Keep your work area clean,

well-lit and free of distractions. Place lights so you are not working

in a shadow.

2. Keep anyone not wearing the appropriate safety equipment away

from the work area.

3. Store unused tools properly in a dry, safe and secure location to

prevent rust, damage or misuse.

PERSONAL SAFETY

WARNING! Wear personal protective equipment approved

by the Canadian Standards Association (CSA) or American

National Standards Institute (ANSI).

PERSONAL PROTECTIVE EQUIPMENT

1. Always wear impact safety goggles that provide front and side

protection for the eyes. Eye protection equipment should comply

with CSA Z94.3-07 or ANSI Z87.1 standards based on the type of

work performed.

2. Wear the appropriate type of full-face shield in addition to safety

googles, as the work can create chips, abrasive or particulate

matter.

3. Wear gloves that provide protection based on the work materials or

to reduce the effects of tool vibration.

a. Do not wear gloves when operating a tool that can snag the

material and pull the hand into the tool.

4. Wear protective clothing and gloves designed for the work

environment, materials and tools.

5. Non-skid footwear is recommended to maintain footing and

balance in the work environment

6. Wear steel toe footwear or steel toe caps to prevent a foot injury

from falling objects.

7. Wear the appropriate rated dust mask or respirator. Wear a NIOSH

approved respirator when working on materials that produce

hazardous fumes, dust or particulate matter.

9029372 DECAL AND UNDERCOAT REMOVAL KIT V1.0

Assistance available at www.princessauto.com or 1-800-665-8685 Page 4

8. The tool may contain high pressure. Use safety glasses and gloves

for protection during operation. Keep hands clear of the exposed

rubber portions of the hose.

9. This tool can cause hearing damage. Wear ear protection gear to

eliminate or reduce the noise. If possible add a muffling device to

the air tool’s exhaust.

PERSONAL PRECAUTIONS

Control the tool, personal movement and the work environment to avoid

personal injury or damage to tool.

1. Do not operate any tool when tired or under the influence of drugs,

alcohol or medications.

2. Avoid wearing clothes or jewelry that can become entangled with

the moving parts of a tool. Keep long hair covered or bound.

3. Do not overreach when operating a tool. Proper footing and

balance enables better control in unexpected situations.

4. Support the workpiece or clamp it to a stable platform. Holding

the workpiece by hand or against your body may lead to personal

injury.

5. Securely hold this tool using both hands. Using a tool with only one

hand can result in loss of control.

6. Keep your fingers away from the trigger/switch while carrying the

tool, attaching an air hose or an accessory. Lock the trigger/switch

safety if available.

7. Avoid unintentional starts. Be sure that the regulator/throttle switch

is in the neutral or OFF position when not in use and before

connecting it to any air source.

8. Never point the air stream or tool at any point of your body, other

people or animals. Debris and dust ejected at high speed can

cause an injury.

9. Serious injury or death may occur from inhaling compressed air.

The air stream may contain carbon monoxide, toxic vapors or solid

particles. Never inhale compressed air directly from the pump or

air tool.

V1.0 DECAL AND UNDERCOAT REMOVAL KIT 9029372

Page 5 Assistance available at www.princessauto.com or 1-800-665-8685

SPECIFIC SAFETY

WARNING! DO NOT let comfort or familiarity with product

(gained from repeated use) replace strict adherence to the

tool safety rules. If you use this tool unsafely or incorrectly,

you can suffer serious personal injury.

WARNING! Some surfaces contain materials which can

be toxic. When working on materials that may contain

lead, asbestos, copper chromium arsenate or other toxic

materials, extra care should be taken to avoid inhalation and

minimize skin contact.

1. Use the correct tool for the job. This tool was designed for a

specific function. Do not modify or alter this tool or use it for an

unintended purpose.

2. Do not use the tool if any parts are damage broken or misplaced.

Repair or replace the parts.

3. Only use a wheel that is specifically designed for use with the

decal and undercoat removal tool. Ensure the wheel is tightly

installed.

4. Do not use a wheel that is dull or damaged. A dull tool requires

more force to use the tool, possibly causing the wheel to break.

This may cause an injury and will damage the workpiece.

5. Only use a wheel that exceeds the Speed Rating (see

Specifications).

6. Always wait until the motor has reached full speed before starting

the task.

7. Use the correct mounting hardware. The mounting hardware

is designed to hold the wheel on the tool to allow optimum

performance and safety of operation. Mismatched mounting

hardware may result in a tool malfunction and cause an injury.

8. Check the wheel for damage before each use. It can break and

cause serious injury or damage the tool and workpiece.

9. Always handle the wheel with care when mounting or removing it.

9029372 DECAL AND UNDERCOAT REMOVAL KIT V1.0

Assistance available at www.princessauto.com or 1-800-665-8685 Page 6

10. Remove adjusting keys and wrenches before using the tool. The

tool may eject an attached wrench or a key and cause an injury to

you or a bystander.

AIR TOOL PRECAUTIONS

1. Use only clean and dry compressed air as a power source.

Contaminated or moist air will gradually damage the tool.

2. Install an in-line shutoff valve or regulator to allow immediate

control over the air supply in an emergency, even if a hose is

ruptured.

3. Discontinue tool use if it does not work properly or air is leaking.

Tag or mark the tool as ‘defective’ or ‘out of service’ until repaired.

4. Check the manufacturer’s maximum pressure rating for air tools

and accessories. Compressor outlet pressure must be regulated

to never exceed the maximum pressure rating of the tool (see

Specifications). Exceeding the maximum PSI rating can create a

bursting hazard, causing injury and property damage.

a. The tool does not regulate the pressure level. The power

output is in direct proportion to the air pressure available. An

external air pressure regulator is required to safely use this

tool.

5. Attach all accessories properly to the tool before connecting the air

supply. A loose accessory may detach or break during operation.

6. Never use oxygen, combustible gas or any other bottled gas as

a power source. Any power source other than an air compressor

could cause an explosion and serious personal injury.

7. Turn OFF the valve and discharge any remaining air pressure after

each use or before adjusting the tool.

8. Do not leave the air tool unattended with its compressed air supply

on. Turn off the compressed air supply and bleed the air tool of any

remaining compressed air before leaving the air tool unattended.

9. Serious injury may occur from loose debris being propelled at

high speeds from the compressed air stream. Always wear OSHA

approved safety glasses to protect the eyes during operation of the

air compressor.

V1.0 DECAL AND UNDERCOAT REMOVAL KIT 9029372

Page 7 Assistance available at www.princessauto.com or 1-800-665-8685

10. Always turn off the air compressor and drain tank pressure

completely before attempting maintenance or attaching air tools.

Release pressure slowly from the system.

11. Do not cover the air vents.

POWER TOOL PRECAUTIONS

1. Do not use any power tool with a malfunctioning power switch

or control. A power tool that fails to respond to the controls is

dangerous and can cause an injury. A qualified technician must

repair and verify the power tool is operating correctly, before it can

be used.

2. Shut the power off and disconnect the decal and undercoat

removal tool from the power supply (if possible) before making

any adjustments, changing accessories, cleaning, servicing or

when storing. Such preventive safety measures reduce the risk of

starting the tool accidentally.

3. Never force the tool. Excessive pressure could bend or break

the decal and undercoat removal tool, resulting in damage to the

tool, your workpiece or serious personal injury. If the decal and

undercoat removal tool runs smoothly under no load, but does not

run smoothly under load, then excessive pressure is being used.

4. Position the decal and undercoat removal tool's safety guard over

the wheel when not in use.

5. Check if the decal and undercoat removal tool's moving parts are

misaligned or binding before each use. Correct the issue before

using the decal and undercoat removal tool to avoid an injury or

damage to the tool.

6. Always be aware of the position of your hands relative to the decal

and undercoat removal tool. Avoid awkward hand positions where

a sudden slip could cause a hand to move into the wheel. Never

reach behind or beneath the decal and undercoat removal tool.

7. Only use accessories that are specifically designed for use with

the decal and undercoat removal tool. Ensure the wheel is tightly

installed.

9029372 DECAL AND UNDERCOAT REMOVAL KIT V1.0

Assistance available at www.princessauto.com or 1-800-665-8685 Page 8

8. Only use a wheel that exceeds the Speed rating (see

Specifications).

9. Before using the decal and undercoat removal tool on a workpiece,

test the decal and undercoat removal tool by running it at the

highest speed rating for at least 30 seconds in a safe position.

Stop immediately if there is any abnormal vibration or wobbling.

Check the tool to determine the cause.

10. Never touch the wheel or workpiece during or immediately after

use. They may be hot and could inflict a burn injury.

11. Do not cover the air vents. Proper cooling of the motor is

necessary to ensure normal life of the tool.

12. Never use a tool with a wheel that is cracked or worn. Change the

wheel before using it.

13. Do not place the decal and undercoat removal tool down until the

wheel has stopped moving. The decal and undercoat removal tool

may catch the surface of work material and wrench itself free,

causing injury to the user or others in the work area.

14. Avoid unintentional starts. Be sure that the regulator/throttle switch

is in the neutral or OFF position when not in use and before

connecting it to any air source.

15. Never point the decal and undercoat removal tool towards yourself.

It could inflict an injury.

KICKBACK PRECAUTIONS

Kickback is a sudden reaction when the decal and undercoat removal

tool snags or is caught on the material. If kickback occurs:

•The wheel may pass over a body part, causing an injury.

•The tool may strike bystanders.

•Kickback can also damage the tool or workpiece.

Kickback can be avoided by taking proper precautions:

1. Maintain a firm grip on the tool and position your body and arms to

allow you to resist a kickback. Kickback will propel the tool in the

direction opposite the wheel's direction of rotation. The tool may

pull out of your grasp.

V1.0 DECAL AND UNDERCOAT REMOVAL KIT 9029372

Page 9 Assistance available at www.princessauto.com or 1-800-665-8685

a. Use clamps or a vice to hold down smaller workpieces.

2. Only use a wheel designed for the tool.

AIR HOSE PRECAUTIONS

1. Inspect the tool's air hose for cracks, fraying or other faults before

each use. Discontinue use if the air hose is damaged or hissing

is heard from the air hose or couplers. Replace the defective air

hose.

2. Do not allow people, mobile equipment or vehicles to pass over the

unprotected air hose. Position the air hose away from high traffic

areas, in a reinforced conduit or place planks on both sides of the

air hose to create a protective trench.

3. Prevent damage to the air hose by observing the following:

a. Never carry the tool by the air hose.

b. Keep the air hose behind the tool and out of the tool's work

path.

c. Keep the air hose away from heat, oil, sharp edges or moving

parts.

d. Do not wrap the air hose around the tool as sharp edges may

pierce or crack the air hose. Gently coil the hose and either

hang on a hook or fasten with a device to keep hose together

when storing.

4. A damaged or disconnected air hose under pressure may whip

around and inflict personal injury or damage the work area. Secure

the compressor's air hose to a fixed or permanent structure with

clamps or cable ties.

5. Install an in-line shutoff valve or regulator to allow immediate

control over the air supply in an emergency, even if a hose is

ruptured.

VIBRATION PRECAUTIONS

1. This tool vibrates during use. Repeated or long-term exposure to

vibration may cause temporary or permanent physical injury. Take

frequent breaks when using the tool.

9029372 DECAL AND UNDERCOAT REMOVAL KIT V1.0

Assistance available at www.princessauto.com or 1-800-665-8685 Page 10

2. If you feel any medical symptoms related to vibrations (such

as tingling, numbness, and white or blue fingers), seek medical

attention as soon as possible.

3. Wear suitable gloves to reduce the effects of vibration.

4. DO NOT use this tool before consulting a physician if one of the

following applies:

a. Pregnant

b. Impaired blood circulation to

the hands

c. Past hand injuries

d. Nervous system disorders

e. Diabetes

f. Raynaud's Disease

UNPACKING

WARNING! Do not operate the tool if any part is missing.

Replace the missing part before operating. Failure to do so

could result in a malfunction and personal injury.

Remove the parts and accessories from the packaging and inspect for

damage.

Contents:

• Decal and Undercoat

Removal Tool

• Eraser Wheel

• (3) Wire Wheel

• Fiber Wheel

V1.0 DECAL AND UNDERCOAT REMOVAL KIT 9029372

Page 11 Assistance available at www.princessauto.com or 1-800-665-8685

IDENTIFICATION KEY

A. Safety Guard

B. Handle

C. Air Coupler Plug

D. Safety Guard

Cover

E. Protective Guard

F. Trigger Lever

G. Fiber Wheel

H. Eraser Wheel

I. Wire Wheel

J. Wire Wheel Hub (not shown)

ASSEMBLY & INSTALLATION

INSTALL AIR COUPLER PLUG

Prepare a standard 1/4 in. NPT coupler plug (sold separately) for use

with your tool.

1. Wrap the external threads of the coupler plug with sealant tape.

a. Wrap tape in a clockwise direction so it will not unravel.

b. Do not tape all the threads. Leave several leading threads

unwrapped for easier alignment.

2. Screw the coupler plug into the tool's air inlet and tighten with a

wrench until snug.

3. Run the compressor at a low volume and check the connection for

air leaks. Do not use the tool until all air leaks are repaired or the

faulty component is replaced.

Figure 1.

9029372 DECAL AND UNDERCOAT REMOVAL KIT V1.0

Assistance available at www.princessauto.com or 1-800-665-8685 Page 12

IMPORTANT! Vibration may cause failure if a quick coupler

is connected directly to the air tool. To overcome this,

connect a leader hose to the tool. A quick coupler may then

be used to connect the leader hose to the air line hose.

INSTALL WHEEL

The decal and undercoat removal tool has three types of wheels for

removing unwanted material from the workpiece: wire, fiber and eraser.

1. Disconnect the power source before installing or servicing the tool.

2. Remove the hex screw that fastens the protective cover to the

safety guard, remove the cover and set both aside.

3. Remove lock washer and center screw from the drive belt shaft.

4. Place the wheel hub onto the shaft. The hex screw heads must be

facing upwards.

• The bent bristles on the wire wheel must point to the left or in

the counterclockwise direction to function correctly.

5. Drop the lock washer into the wheel's center opening, then secure

the wheel with the center screw.

6. Place the protection cover back onto the safety guard. Check that

the wheel is not touching the cover. Adjust the wheel to sit properly

if it is.

7. Secure the cover with the protective screw.

OPERATIONS

Inspect the decal and undercoat removal tooland the wheel periodically.

Repair or replace damaged or worn components and accessories.

Only use identical replacement parts when servicing (see Care &

Maintenance).

Each type of wheel is best used for specific tasks:

•The eraser wheel will peel away the decal, but may leave

an adhesive residue. Remove any residue with an appropriate

cleaning product for the material.

V1.0 DECAL AND UNDERCOAT REMOVAL KIT 9029372

Page 13 Assistance available at www.princessauto.com or 1-800-665-8685

• The fiber wheel will remove rust, corrosion and paint from the

workpiece without marring the underlying surface.

• The wire wheel will remove paint, rust, auto-body coating and

welding slag. A stainless steel wire wheel is needed when cleaning

aluminum workpieces.

1. Determine if you need to clamp or secure the workpiece.

2. Insert the the wheel and tighten the lock washer and screw.

3. Turn on the air source to the lowest volume.

4. Position the sanding drum so that it does not touch anything.

5. Push the safety lever forward, then press the trigger lever down.

6. Hold the decal and undercoat removal tool firmly and apply it to the

workpiece.

7. Move the wheel across the surface slowly side-to-side while pulling

it backward until the material is removed.

8. Lift the decal and undercoat removal tool away from the workpiece

when done.

9. Release the trigger to stop the tool.

10. Stop the compressor once the task is complete and release

residual pressure from the tool and air hose. Disconnect the air

hose from the tool.

ADDITIONAL WIRE WHEEL INSTRUCTIONS

Some areas are difficult to clean with the wire

wheel, such as the corners where the surfaces

of steep-angled structures meet. Holding the tool

perpendicular will prevent the bristles from reaching

into the corner (Fig. 2).

The rotating wire wheel bristles must align with the

joint's direction where two surfaces meet to at an

angle. This will allow the bristles to bend enough to

reach the joint (Fig. 3).

Figure

9029372 DECAL AND UNDERCOAT REMOVAL KIT V1.0

Assistance available at www.princessauto.com or 1-800-665-8685 Page 14

Do not apply excessive pressure on the wire wheel.

The bristles will splay outward and the ends may not

strike the material correctly, resulting in a poor

cleaning job.

Rotate the tool from side-to-side at your wrist when

cleaning a curved surface, so all the bristles are

striking the workpiece throughout the curve.

CARE & MAINTENANCE

1. Maintain the tool with care. A tool in good condition is efficient,

easier to control and will have fewer problems.

2. Inspect the tool components periodically. Repair or replace

damaged or worn components. Only use identical replacement

parts when servicing.

3. Only use accessories intended for use with this tool. Follow

instructions for changing accessories.

4. Keep the tool handles or gripping surfaces clean and dry.

5. Maintain the tool’s labels and name plates. These carry important

information. If unreadable or missing, contact Princess Auto Ltd.

for replacements.

WARNING! Only qualified service personnel should repair

the tool. An improperly repaired tool may present a hazard

to the user and/or others.

AIR TOOL LUBRICATION

NOTICE! Only use air tool oil to lubricate the tool. Other

lubricants are not suitable and will damage the tool or cause

a malfunction during use.

NOTICE! Never use a penetrating oil to lubricate an air tool.

Penetrating oil acts as a solvent that will dissolve the tool’s

grease packing and may damage the o-rings, causing the

tool to seize or malfunction.

1. All air tools have an internal coating of grease to prevent corrosion

during shipping and storage. Remove this grease by adding a

Figure

V1.0 DECAL AND UNDERCOAT REMOVAL KIT 9029372

Page 15 Assistance available at www.princessauto.com or 1-800-665-8685

generous amount of air tool oil in the air inlet and then run the tool

under no load until the exhaust is clear.

2. Manually add a drop or two of air tool oil into the tool’s coupler

plug before each use and after every hour of continuous use. The

tool will not work properly without lubrication and parts will wear

prematurely.

3. Avoid adding too much air tool oil as this can cause premature

power loss and eventual tool failure. A qualified technician will

need to take the tool apart and clean out the excess oil.

4. Apply a generous amount of air tool oil to the tool before storing

it for an extended period of time (overnight, weekend, etc.). Run

the tool for approximately 30 seconds to ensure the oil is evenly

distributed throughout the tool. Store it in a clean and dry location.

REPLACE WORN WHEELS

The wheels will eventually wear down and become less effective.

The bent bristle wheels can be resharpened and the fiber and eraser

wheels can be cleaned, but eventually they must all be replaced at

some point.

1. Remove the wheel and hub from the tool.

2. Remove the three hub screws and set aside.

3. Remove the upper half of the hub and set aside.

4. Remove the old wheel and either recycle or discard it.

5. Push the new wheel into place on the hub. The bent wire bristles

must point counterclockwise. The eraser, fiber and straight shaft

wheels do not have a required orientation.

6. Place the upper hub onto the newly installed wheel and align the

bolt holes.

7. Fasten the three screws into place.

8. Reinstall the assembled wheel onto the tool.

9029372 DECAL AND UNDERCOAT REMOVAL KIT V1.0

Assistance available at www.princessauto.com or 1-800-665-8685 Page 16

SHARPENING WIRE WHEEL BRISTLES

WARNING! Prevent a personal injury or accident by

disconnecting the wheel from its power source before

servicing or changing accessories.

IMPORTANT! The bristle sharpening instructions are only

for the bent bristle wire wheel. The straight bristle wire

wheel cannot be re-sharpened once the bristles are dull.

The bent bristles will become dull with time and use. The workpiece's

surface will not be as clean, which may cause you to apply more

pressure on the tool to attain the same result. This will damage the wire

wheel and you will need to replace it more frequently.

Regular sharpening will extend the wire wheel's lifespan. Sharpen the

bristles by following the instructions below.

1. Remove the wire wheel, flip it so the bent bristles are reversed

and reinstall the wheel. The bristles will now point to the right or

clockwise.

2. Prepare a grinding stone with medium to fine grit. Follow the stone

manufacturer's instructions.

3. Position the decal and undercoat removal tool so that it does not

touch anything.

4. Push the safety lever forward, then press the trigger lever down.

5. Lower the tool until the bristle ends touch the grinding stone. Apply

slight pressure for 15 to 30 seconds without moving the tool, then

lift it from the grinding stone.

6. Release the trigger to stop the tool.

7. Remove the wire wheel and flip it so it is back in the original

orientation with the bristles point counterclockwise.

DISPOSAL

Recycle a tool damaged beyond repair at the appropriate facility.

Contact your local municipality for a list of disposal facilities or by-laws

for electronic devices, batteries, oil or other toxic liquids.

V1.0 DECAL AND UNDERCOAT REMOVAL KIT 9029372

Page 17 Assistance available at www.princessauto.com or 1-800-665-8685

TROUBLESHOOTING

Visit a Princess Auto Ltd. location for a solution if the tool does not

function properly or parts are missing. If unable to do so, have a

qualified technician service the tool.

AIR TOOL

Problem(s) Possible Cause(s) Suggested Solution(s)

Tool runs at

normal speed,

but loses power

under load.

1. Motor parts worn. 1. Have a qualified technician

service the tool.

2. Replace tool or parts.

Tool runs slowly.

Air flows slightly

from exhaust.

And/Or

Air flows slightly

from nozzle.

1. Motor parts jammed

with dirt particles.

Airflow blocked by

dirt.

2. Air regulator in

closed position.

3. Air flow or air

pressure is too low.

4. Damage or

excessive wearing of

internal parts.

1. Check air inlet filter for

blockage.

a. Pour air tool lubricating

oil into air inlet as per

lubrication instructions for

clearing shipping grease.

b. Operate tool in short bursts

to clear debris.

c. If tool still jammed, clean

tool and lubricate per

lubrication instructions.

2. Open the air regulator to

desired airflow.

3. Adjust air flow or air pressure

to match tool requirements (see

Specifications).

4. Have a qualified technician

service the tool.

a. Replace tool or parts.

Tools will not run.

Air flows freely

from exhaust.

1. Damage or

excessive wearing of

internal parts.

2. Insufficient internal

lubrication.

1. Have a qualified technician

service the tool.

2. Replace tool or parts.

3. Lubricate tool per air tool

lubrication instructions.

9029372 DECAL AND UNDERCOAT REMOVAL KIT V1.0

Assistance available at www.princessauto.com or 1-800-665-8685 Page 18

Problem(s) Possible Cause(s) Suggested Solution(s)

Tool will not shut

off.

1. Throttle valve o-ring

dislodged from inlet

valve seat.

2. Trigger mechanism

jammed or dirty.

1. Replace throttle valve o-rings.

2. Clean trigger mechanism and

lubricate.

Loss of power or

erratic

performance.

1. Excessive drain

on the air hose.

Incorrect size or

type of hose

connectors.

2. Moisture or

restriction in the air

hose/tank

3. Air compressor has

insufficient flow.

1. Check the air hose and confirm

the hose fitting is correct for the

inlet bushing.

2. Depressurize system and drain

tank and air hose of water.

3. Ensure tool is connected to a

compressor with a rate flow that

matches the tool.

POWER TOOL

Problem(s) Possible Cause(s) Suggested Solution(s)

The decal and

undercoat

removal tool

will not start.

1. Supplied power is

interrupted.

2. Motor components are

defective.

3. Motor has overheated.

1. Check that power supply is

still available.

2. Have a qualified technician

service the tool.

3. Allow motor to cool before

attempting to use.

Motor starts

slow and

doesn't reach

operation

speed.

1. Air flow or air pressure is

too low.

2. Motor is damaged.

1. Adjust air flow or

air pressure to match

tool requirements (see

Specifications).

2. Have a qualified technician

service the tool.

Tool is making

unusual

sounds.

1. The decal and undercoat

removal tool's parts may be

rubbing or binding.

2. Worn tool components

1. Check for obstructions

or misaligned tool

components. Lubricate,

repair or replace the

components based on the

particular problem.

2. Check and replace worn

parts.

V1.0 DECAL AND UNDERCOAT REMOVAL KIT 9029372

Page 19 Assistance available at www.princessauto.com or 1-800-665-8685

Problem(s) Possible Cause(s) Suggested Solution(s)

Overheating 1. Forcing machine to work

too fast.

2. Blocked motor housing

vents.

1. Allow machine to work at its

own rate.

2. Blow dust out of motor

using compressed air.

PARTS BREAKDOWN

PARTS LIST

#DESCRIPTION QTY

1 Regulator Set 1

2 Valve Stem Set 1

3 Air Inlet 1

4 Muffler Body 1

5 Exhaust Sleeve Set 1

6 Protecting Rubber 1

7 Housing 1

8 Spring pin 1

# DESCRIPTION QTY

9 Trigger Lever 1

10 Bearing (696zz) 1

11 Rear Plate 1

12 Rotor Blade 4

13 Rotor (9T) 1

14 Cylinder Set 1

15 Front Plate 1

16 Bearing (608zz) 1

9029372 DECAL AND UNDERCOAT REMOVAL KIT V1.0

Assistance available at www.princessauto.com or 1-800-665-8685 Page 20

La page charge ...

PROPOINT 9029372 Le manuel du propriétaire

Marque: PROPOINT

Modèle: 9029372

Catégorie: Outils électroportatifs

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: PROPOINT 9029372 Owner's manual

PROPOINT 9029372 Le manuel du propriétaire

PROPOINT 9029372 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents