Haier CHDE5000AW User Manual and Installation Instructions

User Manual and Installation Instructions

Gas & Electric Dryer

Sécheuses à chargement frontal à gaz et

électrique

Manual para el usuario e instrucciones

de instalación. Secadora a gas y eléctrica

Model #/ Modéle #/ Para Modelo de #

HDE/HDG5000AW ; HDE/HDG5300AW

Quality

■

Innovation

■

Style

(Picture for illustration purposes only. Actual model may vary per model purchased.)

Front Load Dryers

CHDE/HDG5000AW ; CHDE/HDG5300AW

1

English

PAGE

IMPORTANT SAFETY INSTRUCTIONS.......................................2-4

INSTALLATION INSTRUCTIONS..............................................5-24

Tools and Materials Required ............................................................ 5

Electrical Requirements ..................................................................5-6

Unpacking Your Dryer ..................................................................... 6

Exhaust System Requirements ........................................................7-8

Gas Supply Requirements ................................................................ 9

Location of Your Dryer ...................................................................10

Location of Your Dryer in a Closet....................................................11

Manufactured (Mobile) Home Instruction .........................................12

Procedure for Reversing the Door............................................... 13-17

Changing the Drum Light ................................................................18

Electrical Installation ......................................................................19

3-Wire Cord Connections ..............................................................20

4-Wire Cord Connections ..............................................................21

Gas Connections ..........................................................................22

Replacement Parts .........................................................................24

OPERATING INSTRUCTIONS ............................................... 25-38

Understanding the Control Panel

(HDE/HDG5300AW,CHDE/HDG5300AW)

....... 25-27

Understanding the Control Panel 27-29

Preparations before Drying .............................................................30

Load clothes into Dryer ...................................................................31

Auto Dry Cycle

..........................

32-33

Auto Dry Cycle 34

Manual Dry Cycle 35

Manual Dry Cycle 36

Other Features...............................................................................37

Normal Operating Sounds..............................................................38

CARE AND CLEANING GUIDE

.......................................................38

TROUBLESHOOTING.................................................................. 39

LIMITED WARRANTY .................................................................40

TABLE OF CONTENTS

(HDE/HDG5000AW,CHDE/CHDG5000AW)

.......

(HDE/HDG5300AW,CHDE/CHDG5300AW)

(HDE/HDG5000AW,CHDE/CHDG5000AW)

(HDE/HDG5300AW,CHDE/CHDG5300AW)

(HDE/HDG5300AW,CHDE/HDG5000AW)

..................................

..............................

English

WARNING - To reduce the risk of ﬁre, electric shock, or

injury to persons when using your appliance, follow the

basic precautions, including the following:

1. Read all of the instructions before using this appliance.

2. Don’t dry articles that have been previously cleaned in, washed in,

soaked in, or spotted with gasoline, dry clean solvents or other

ﬂammable explosive sub stains as they give off vapors which could

ignite or explode.

3. Do not allow children to play on or in the appliance. Close

supervision of children is necessary when the appliance is used near

children.

4. Before the appliance is removed from service or discarded, remove

the door to the drying compartment.

5. Do not reach into the appliance if the drum is moving.

6. Do not install or store this appliance where it will be exposed to

water and/or to the weather.

7. Do not tamper with controls.

8. Do not repair or replace any part of the appliance or attempt any

servicing unless speciﬁcally recommended in the user-repair

instructions that you understand and have skills to carry out.

9. Do not use fabric softeners or products to eliminate static unless

recommended by the manufacturers of the fabric softener or

product.

10. Do not use heat to dry articles or products to eliminate static unless

recommended by the manufacturers of the fabric softener or

product.

11. Clean lint screen before or after each load.

12. Keep area around the exhaust opening and adjacent surrounding

areas free from the accumulation of lint, dust and dirt.

13. Keep the dryer area clear and free from items that would obstruct

the ﬂow of combustion and ventilation air through the louvered panel

located on the rear of the dryer.

14. The interior of the appliance and the exhaust duct should be cleaned

periodically by qualiﬁed service personnel.

3

IMPORTANT SAFETY

INSTRUCTIONS

English

4

Thank you for using our Haier

product. This easy-to-use manual

will guide you in getting the best

use of your dryer.

Remember to record the model and

serial number. They are on a label

in back of the dryer.

Model number

Serial number

Date of purchase

Staple your receipt to your manual.

You will need it to obtain warranty service.

15. Do not place items exposed to cooking oils in your dryer. Items

contaminated with cooking oil may contribute to a chemical reaction

than could cause a load to catch ﬁre.

16. If material has been used with any ﬂammable liquids or solids, it

should not used in the dryer until all traces of ﬂammable liquids and

its fumes have been removed.

17. This dryer must be properly installed in accordance with the

installation instructions before it is used. See grounding instructions in

the installations sections.

18. Proper grounding must be ensured to reduce the risk of electric shock

and force. Check with a qualiﬁed electrician or service personnel if

you are in doubt as to whether the dryer is properly grounded.

19. Use the dryer only for its intended purpose: drying clothes.

20. Always disconnect dryer from electrical supply before attempting any

service. Disconnect power cord by grasping the plug, not the cord.

21. Replace worn power cord and/or loose plugs.

22. To reduce the risk of electric shock or ﬁre, do not use extension cords

or adapters to connect dryer electrical power source.

Risk of child entrapment. Before you throw away your old dryer,

take off the door so that children may not get trapped inside.

SAVE THESE

INSTRUCTIONS

DANGER

5

WARNING

Risk of Fire:

Tools and materials required

• Phillips-Head and ﬂathead screwdrivers

• Channel-lock adjustable pilers

• 1/2-inch open-end wrench

• Carpenter’s level

• Measuring tape (12ft. min.)

• Duct tape

• Pipe thread sealer (Gas)

• Rigid or ﬂexible metal 4 inch (102cm) duct

• Vent hood

Safety Warning:

1. Before starting installation, make sure that the gas shut off valve is in the

off position.

2. All old gas connectors and gas piping should be discarded.

ELECTRICAL REQUIREMENTS

Electric Dryer:

(CHDE/HDE5000AW

and

CHDE/HDE5300AW)

Circuit

Individual 30 Amp branch circuit fused with 30 Amp time-delay fuses or circuit

breakers. Use seperately fused circuits for washers and dryers, and DO NOT

operate a washer and dryer on the same circuit.

INSTALLATION INSTRUCTIONS

English

1.Clothes dryer installation must be performed by a qualiﬁed installer.

2.Install the clothes dryer according to the manufacturer’s instructions

and local codes.

3.Do not install a clothes dryer with ﬂexible plastic venting materials.

If ﬂexible metal (foil type) duct is installed,it must be of a speciﬁc

type identiﬁed by the appliance manufacturer as suitable for use

with clothes dryers. Flexible venting materials are known to collapse,

be easily crushed,and trap lint.These conditions will obstruct clothes

dryer airﬂow and increase the risk of ﬁre.

4.To reduce the risk of severe injury or death, follow all installation

instructions.

SAVE THESE INSTRUCTIONS

English

6

Power Supply

3 or 4 wire, 120/240 Volt, 1 Phase, 60Hz, AC

(Canada - 120/240 Volt, 1 Phase, 60 Hz, AC)

Power Supply Cord Kit

(Not supplied when sold in US. Must be purchased to meet local electrical

codes.) The dryer MUST employ a 3-conductor power supply cord NEMA 10-30

Type SRDT rated at 240 Volt AC minimum, 30 Amp, with 3 open end spade lug

connectors with upturned ends or closed loop connectors and marked for use

with clothes dryers.

(When sold in Canada - 4-wire power supply cord provided and

attached on dryer)

Dryers being installed in a manufactured (mobile) home MUST employ a

4-wire power supply cord NEMA 14-30 type SRDT or ST (as required) rated

to 240 Volt AC minimum, 30 Amp, with 4 open-end spade lug connectors

with upturned ends or closed loop connectors and marked for use with clothes

dryers. See Electrical Connections for more information on a 4-wire system.

Outlet Receptacle

NEMA 10-30R receptacle should be located so the power supply cord is

accessible when the dryer is in the installed position. (Canada - NEMA 14-30R

receptacle)

ELECTRICAL REQUIREMENTS

Gas Dryer: (CHDG/HDG5000AW and CHDG/HDG5300AW)

Circuit

Individual 15 Amp branch circuit fused with 15-Amp maximum time delay fuse

or circuit breakers.

Power Supply

3 wire, 120 Volt, 1 Phase, 60Hz, AC

Power Supply Cord

The dryer is equipped with a 120 Volt 3-wire power supply cord.

NOTE: This dryer is equipped with a three-prong grounding plug for your

protection against shock hazard and should be plugged into a properly

grounded three-prong receptacle. Do not under any circumstance cut or

remove grounding prong from plug.

Unpacking Your Dryer

1. Remove all packaging material. This includes the foam base and all adhesive

tape holding the dryer accessories inside and outside.

2. Inspect and remove any remains of packaging, tape or printed materials

before using the dryer.

The following are speciﬁc requirements for

proper and safe operation of your dryer. Failure

to follow these instructions can create excessive

drying times and ﬁre hazards.

1. Do not use plastic ﬂexible duct to exhaust the dryer. Excessive lint can build up

inside exhaust system and create a ﬁre hazard and restrict air ﬂow. Restricted

air ﬂow will increase drying time. If your present system is made up of plastic

duct or metal foil duct, replace it with a rigid or ﬂexible metal duct. Ensure

present duct is free of any lint prior to installing dryer duct.

2.

The dryer shall not be exhausted into a chimney, a wall, a ceiling, an attic, a

crawl space, or a concealed space of a building;

The dryer exhaust system

MUST be

exhausted to the outdoors. If the dryer is not exhausted

outdoors, some

ﬁne lint will be expelled into the laundry area. An accumulation

of lint in any

area of the home can create a health and ﬁre hazard.

3. Exceeding the length of duct pipe or number of elbows allowed in the

“Maximum Length” chart can cause an accumulation of lint in the exhaust

system. Plugging the system could create a ﬁre hazard, as well as increase

drying times.

4. Do not screen the exhaust ends of the vent system. Lint can become caught in

the screen, increasing drying time. Use an approved vent hood to terminate the

duct outdoors, and seal all joints with duct tape.

5. All male duct pipe ﬁttings must be installed downstream with the ﬂow of air.

6. The duct shall not be assembled with screws or other fastening means that extend

into the duct and catch lint.

7. Do not allow combustible material (clothing, draperies/curtains, paper, etc.) to

come in contact with exhaust system.

Explosion hazard:

Do not install the dryer where gasoline or other ﬂammables are kept or

stored. If the dryer is installed in a garage, it must be a minimum of 18

inches (45.7cm) above the ﬂoor. Failure to do so can result in death,

explosion, ﬁre or burns.

Exhaust Requirements:

Use only rigid or ﬂexible metal duct and

approved vent hood which has a

swing-out

damper hat open when the dryer is

in operation. When the dryer

stops, the dampers automatically close to prevent

drafts

and the entrance of

insects and rodents. To avoid restricting the outlet,

WARNING

EXHAUST SYSTEM REQUIREMENTS

English

7

maintain a minimum of

clearance between the vent hood

and the ground or

any other obstruction. The vent ﬂap should be able to move

freely, although

vertical orientation of the exhaust system is acceptable. Certain

extenuating

circumstances could affect the performance of the dryer:

1. Only rigid or ﬂexible metal duct work should be used.

2. Venting vertically through a roof may expose the exhaust

system to down

drafts causing an increase in vent restriction.

3. Running the exhaust system through an uninsulatedarea may

cause

condensation and faster accumulation of lint.

4. Compression of crimping of the exhaust system will cause

an increase in

vent restriction.

The exhaust system should be inspected and cleaned a minimum of every 12

months with normal usage. The more the dryer is used the more often you

should check the exhaust system and vent hood for proper operation.

Side and Bottom Exhaust

For your convenience, your dryer can be exhausted through the side or the

bottom. If you need to change the exhaust on the dryer to the side or the

bottom of the cabinet, you will need to order the exhaust kit from your Haier

dealer or call 1- 800-313-8495

English

RECOMMENDED MAXIMUMM

Exhaust Hood Types

Recommended

Use only for short

run installations

No. of 90º

elbows

Rigid Metal Rigid Metal

0 90 ft. 60 ft.

1 60 ft. 45 ft.

2 45 ft. 35 ft.

3 35 ft. 25 ft.

12 inches (30.5cm)

The total length of ﬂexible metal duct shall not exceed 2.4 m.

5. In Canada, that only those foil-type ﬂexible ducts, if any, speciﬁcally identiﬁed

for use with the appliance by the manufacturer shall be used. In the United

States, that only those foil-type ﬂexible ducts, if any, speciﬁcally identiﬁed for

use with the appliance by the manufacturer and that comply with the UL Outline

for Clothes Dryer Transition Duct, Subject 2158A (2006), shall be used.

6. In Canada, that the exhaust duct shall be 102 mm in diameter. In the United

States, the required exhaust duct diameter.

8

GAS SUPPLY REQUIREMENTS

English English

9

WARNING

ADVERTENCIA

ADVERTISSMENT

PRECAUCIÓN

PRECAUCIÓN PRECAUCIÓN

ATTENTION

CAUTION

Replace copper connecting pipe that is not plastic

coated. Stainless steel or plastic-coated brass

MUST be used.

1. Installation MUST conform with local codes. In the absence of local codes,

installation must conform with the National Fuel Gas Code, ANSI Z223.1 (latest

edition) or in Canada, the current CAN/CGA B149.1

2.

The gas supply line should be 1/2 inch (1.27cm) pipe.

3.

If codes allow, flexible metal tubing may be used to connect your dryer to the

gas supply line. The tubing MUST be constructed of stainless steel or plastic-

coated brass.

4.

The gas supply line MUST have an individual manual shutoff valve installed

within 6 feet (183cm) of the dryer in accordance with the National Fuel Gas

Code, ANSI Z223.1/NFPA 54.

In Canada, an individual manual shut-off valve MUST be installed in

accordance with the B149.1, Natural Gas and Propane Installation Code.

5. A 1/8 inch (0.32cm) N.P.T. plugged tapping, accessible for test gauge

connection, MUST be installed immediately upstream of the gas supply

connection to the dryer.

6. The dryer MUST be disconnected from the gas supply piping system during

any pressure testing of the gas supply piping system at test pressures in excess

of 1/2 psig (3.45kPa).

7.

The dryer MUST be isolated from the gas supply piping system during any

pressure testing of the gas supply piping system at test pressures equal to or

less than 1/2 psig (3.45 kPa).

English

10

Do Not Install Your Dryer:

1. In an area exposed to dripping water or outside weather conditions.

2. In an area where it will come in contact with curtains, thick carpet, or anything

that will obstruct the ﬂow of combustion and ventilation air.

3. On carpet, ﬂoor must be solid with a maximum slope of 1inch (2.54 cm). Any

ﬂoor unevenness should be corrected with leveling legs located on the bottom

of the dryer.

Installation in Alcove or Closet:

1. DO NOT install your dryer in a closet with a solid door.

2. A dryer installed in a bedroom, bathroom, alcove or closet MUST be

exhausted outdoors.

3. No other fuel burning appliance shall be installed in the same closet as the

gas dryer.

4. Refer to the images on this page to ensure the installation provides the

minimum amount of clearance required for ventilation.

5. When installing the dryer in a closet with a door, a minimum of 120 square

inches (774.2 square cm) of ventilation in the door is required. Openings must

be equally divided at the top and bottom of the door and airﬂow must be

unobstructed. A louvered door with equivalent air openings for the length of

the door is acceptable.

LOCATION OF YOUR DRYER

8

2

5

m

6

8

6

m

1010mm

1295mm(51”)

960mm(37-13/16“)

39-3/4”

2

7

”

3

2

-

1

/

2

”

English

Following are instructions concerning and the minimum clearances required for

any closet, recessed area, or customized under-counter installation:

• Additional distances facilitate installation and servicing.

• Addtional clearances might be required for wall, door and ﬂoor moldings.

• Additional distances of 1 in. (25.4mm) on all sides of the dryer is

recommended to reduce noise transfer.

• For closet installation with a door, minimum ventilation openings in the top

and bottom of the door are required. Louvered doors with equivalent ventilation

openings are acceptable. Companion appliance spacing should be

considered.

LOCATION OF YOUR DRYER IN A CLOSET OR RECESSED AREA

11

32.5"

1 5 "

1

"

0

"

( 5.4mm )

2

( 0 mm )(8 25m m)

( 3

8

.1

mm)

3"

(76mm)

3"

(76mm)

60"

2

（）

387.1cm

2

60"

2

（）

387.1cm

2

English

12

1. Dryer MUST be exhausted outside (outdoors, not beneath the manufactured

home) using metal ducting that will not support combustion. Metal ducting must

be 4 inch (10.16 cm) in diameter with no obstructions. Rigid metal duct

is preferred.

2. If dryer is exhausted through the ﬂoor and area beneath the manufactured

home is enclosed, the exhaust system MUST terminate outside the enclosure

with the termination securely fastened to the mobile home structure.

3. When installing a gas dryer into a manufactured home, a provision must be

made for outside make up air. This provision is to be not less than twice the

area of the dryer exhaust outlet.

4. This dryer MUST be fastened to the ﬂoor using P/N 0030807899

Manufactured Home Installation Kit. Follow the instructions supplied with

the kit.

5. Refer to previous sections for other important venting requirements.

6. Installation must conform to current Manufactured Home Construction & Safety

Standard (which is a Federal Regulation Title 24 CFR-Part 32-80) or when

such standard is not applicable, with American National Standard for Mobile

Homes. In Canada, the CSA Z240 is applicable.

MANUFACTURED (MOBILE) HOME INSTALLATION

English

Before you reverse the door, place a soft cloth

on the work space to protect the surface of the

door.

1. Open the dryer door.

2. Using the long phillip screw driver,

remove the left one screw from the hinge

that attach the dryer door to the front

panel of the dryer. (Fig 1)

3. Using the long phillip screw driver,

remove the right 2 screws from the hinge

that attach the dryer door to the

front panel of the dryer. (Fig 2)

Note: While removing the door screws,

the screwdriver must be straight. Screws

may not come off if screw driver is at an

angle.

4. To disengage the door from the panel,

hold the door close to the hinge and lift

straight up. (There are 3 tabs in the back

of the hinge that will be disengaged).

(Fig 3)

The door on your dryer can be changed from a right-side opening to a left-

side opening, if you need.

Tools required: 1. Long magnetic head

phillip screw driver

2. Power Drill

13

Fig 1

Fig 2

Fig 3

NOTE: Be careful while removing the door. Lift

with caution or door hinge tab may break.

PROCEDURE FOR REVERSING THE DOOR

English

5. Lay the door on a soft surface to protect

the door surface with the glass facing up,

remove the 8 screws using the power drill

holding hinge cover and strike

panel. (Fig 4)

6. Remove the hinge cover, then remove

the 8 screws which hold the hinge knots

“B” “T”. (Fig 5 and Fig 6)

1413

Fig. 5

Fig. 6B

Fig. 6A

Fig. 4

Strike Panel

Hinge Cover

NOTE: If hinge knots (T & B) are not properly placed the

hinge cover may not align with the door.

English

7. There are 3 parts included which are symmetrical to the 3 removed parts

(Fig 7)

1615

A

Fig. 7

Fig. 9A

B

C

8. On the opposite side first install the hinge (Fig 7C) to the door using Top

and Bottom Hinge Knot “T” and “B”. (Fig 9A and 9B)

Fig. 8

Fig. 9B

Note: Be careful not to get the top and bottom hinge knots mixed up.

English

10. Remove the 3 plastic plugs located outside the dryer door opening. Install the

3 plastic plugs into the hinge holes in the dryer front panel on the right side.

(Fig 11A and 11B)

9. Now install both the hinge cover and the strike panel (Fig. 7A and 7B) to the

door as shown in Fig. 10. Use the same 8 screws that were earlier removed

Be carefull not to strip during tightening the screws.

1615

Fig. 10

B

A

Fig. 11

11. To hang door, place hinge tab’s against the 3 holes on the front panel left

side. Press down to engage the tab’s and line up the 3 holes.

(Fig 12A and 12B).

12. Install 2 left screws but do not tighten, then install 1 right screw and tighten.

Now tighten the 2 left screws. (Fig 13)

13. Close door to make sure it is aligned.

English

17

A

B

Fig. 12

Fig. 13

English

1. For your safety, please unplug the power cord before changing the drum light.

2. Open the dryer door, ﬁnd the location of the drum light. Using a phillip head

screw driver remove the light cover (as shown below).

3. Remove the bulb by turning it counterclockwise. Replace the bulb with a

10-watt lamp only, then install the cover and tighten the screw.

4. Use your dryer after plugging it in the electrical socket.

CHANGING THE DRUM LIGHT

18

Screw

English

The following are speciﬁc requirements for proper

and safe electrical installation of your dryer.

Failure to follow these instructions can create

electrical shock and/or ﬁre hazard.

WARNING

1. This appliance must be properly grounded. Electrical shock can result if the

dryer is not properly grounded. Follow the instructions in this manual for

proper grounding.

2. Do not use an extension cord with this dryer. Some extension cords are not

designed to withstand the amounts of electrical current this dryer utilizes and

can melt, creating electric shock and/or ﬁre hazard. Locate the dryer within

reach of the receptacle for the length power cord to be purchased, allowing

some slack in the cord. Refer to the electrical requirements in this manual for

the proper power cord to be purchased.

3. A UL approved strain relief must be installed onto power cord. If the strain

relief is not attached, the cord can be pulled out of the dryer and can be cut

by any movement of the cord, resulting in electrical shock.

4. Do not use an aluminum wire receptacle with copper-wired power cord and

plug (or vice versa ). A chemical reaction occurs between copper and

aluminum and can cause electrical shorts. The proper wiring and receptacle

is a copper-wired power cord with a copper-wired receptacle.

NOTE: Dryers operating on 208 Volt power supply will have longer drying times

than operation on 240 Volt power supply.

Improper connection of the equipment grounding conductor can

result in a risk of electrical shock. Check with a licensed

electrician if you are in doubt as to whether the appliance is

properly grounded.

1. Gas dryers are equipped with a factory installed three-prong 15 Amps ~120

Volts (grounding) plug for your protection against shock hazard and should be

plugged directly into a properly grounded three-prong receptacle. Do not cut

or remove the grounding prong from this plug.

ELECTRICAL INSTALLATION

ELECTRIC Dryer (CHDE/HDE5000AW and CHDE/HDE5300AW)

GAS Dryer (CHDG/HDG5000AW

and

CHDG/HDG5300AW)

19

GROUNDING INSTRUCTIONS

This appliance must be grounded. In the event of malfunction or breakdown,

grounding will reduce th risk of electric shock by providing a path of least

resistance for electric current. This appliance is equipped with a cord having an

equipment-grounding conductor and a grounding plug. The plug must be plugged

into an appropriate outlet that is properly installed and grounded in accordance

with all local codes and ordinances. This appliance must be connected to a

grounded metal, permanent wiring system, or an equipment-grounding conductor

must be run with the circuit conductors and connected to the equipment-grounding

terminal or lead on the appliance.

La page charge ...

Haier CHDE5000AW User Manual and Installation Instructions

Ce manuel convient également à

Haier CHDE5000AW User Manual and Installation Instructions

dans d''autres langues

Documents connexes

Autres documents