KitchenAid KFFS20EYBL02 Le manuel du propriétaire

Marque: KitchenAid

Modèle: KFFS20EYBL02

Catégorie: Frigos

Taper: Le manuel du propriétaire

Ce manuel convient également à

THANK YOU for purchasing this high-quality product. If you should experience a problem not covered in TROUBLESHOOTING,

please visit our website at www.kitchenaid.com for additional information. Ifyou still need assistance, call us at 1-800-422-1230.

In Canada, visit our website at www.kitchenaid.ca or call us at 1-800-807-6777.

You will need your model and serial number, located on the inside wall of the refrigerator compartment.

Para obtener acceso a "lnstrucciones para el usuario del refrigerador" en espa_ol, o para obtener informaci6n adicional acerca de

su producto, visite: www.kitchenaid.com.

Necesitara su nQmerode modelo y de serie, ubicado en el interior del compartimiento del refrigerador.

Table of Contents / Table des mati res

REFRIGERATOR SAFETY ..................................................................... 2

Proper Disposal of Your Old Refrigerator ........................................... 2

INSTALLATION INSTRUCTIONS ......................................................... 3

Unpack the Refrigerator ...................................................................... 3

Location Requirements ....................................................................... 3

Electrical Requirements ...................................................................... 6

Water Supply Requirements ............................................................... 6

Connect the Water Supply .................................................................. 6

Door Closing and Door Alignment ...................................................... 9

FILTERS AND ACCESSORIES ............................................................. 9

Water Filtration System ....................................................................... 9

Install Air Filter ................................................................................... 10

Install Produce Preserver .................................................................. 10

Accessories ....................................................................................... 11

REFRIGERATOR USE ......................................................................... 11

Opening and Closing Doors .............................................................. 11

Water Dispenser ................................................................................ 13

Ice Maker ........................................................................................... 13

REFRIGERATOR FEATURES ............................................................. 14

Refrigerator Shelves .......................................................................... 14

Pantry Drawer ................................................................................... 14

Crisper ............................................................................................... 15

DOOR FEATURES ............................................................................... 15

Condiment Bins ................................................................................. 15

Fresh Bin ........................................................................................... 15

Half-Height Bin .................................................................................. 16

REFRIGERATOR CARE ....................................................................... 16

Cleaning ............................................................................................ 16

Changing the Light Bulbs ................................................................. 16

TROUBLESHOOTING .......................................................................... 17

WATER FILTER CERTIFICATIONS .................................................... 22

PERFORMANCE DATA SHEET .......................................................... 23

WARRANTY .......................................................................................... 24

SleCURITle DU RleFRIGleRATEUR ..................................................... 26

Mise au rebut adequate de votre vieux refrig_rateur ....................... 27

INSTRUCTIONS D'INSTALLATION ................................................... 27

Exigences d'emplacement ............................................................... 28

Retrait et r6installation des portes du

refrig6rateur et de I'avant du tiroir .................................................... 28

Specifications _lectriques ................................................................. 31

Sp6cifications de I'alimentation en eau............................................ 31

Raccordement &I'alimentation en eau............................................. 31

Installation et demontage des poignees .......................................... 33

Fermeture et alignement de la porte ................................................ 34

FILTRES ET ACCESSOIRES ............................................................... 35

Syst_me de filtration de I'eau ........................................................... 35

Installation du filtre & air .................................................................... 35

Installation du conservateur pour produits frais ............................... 36

Accessoires ....................................................................................... 37

UTILISATION DU RleFRIGleRATEUR ................................................. 37

Ouverture et fermeture des portes ................................................... 37

Utilisation des commandes .............................................................. 37

Distributeur d'eau ............................................................................. 39

Machine &glag;ons ............................................................................ 40

CARACTleRISTIQUES DU RleFRIGleRATEUR .................................. 40

Tablettes du refrig6rateur ................................................................. 40

Garde-manger ................................................................................... 41

Bac &legumes .................................................................................. 41

CARACTleRISTIQUES DE LA PORTE ................................................ 42

Balconnets & condiments ................................................................. 42

Balconnet frafcheur ........................................................................... 42

Balconnet mi-hauteur ....................................................................... 42

ENTRETIEN DU RleFRIGleRATEUR ................................................... 42

Nettoyage .......................................................................................... 42

Remplacement des ampoules d'eclairage ....................................... 43

DI_PANNAGE ........................................................................................ 44

FEUILLE DE DONNleES SUR LA PERFORMANCE .......................... 50

GARANTIE ............................................................................................ 51

W10477770A

REFRIGERATOR SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:

• Plug into a grounded 3 prong outlet.

• Do not remove ground prong.

• Do not use an adapter.

• Do not use an extension cord.

• Disconnect power before servicing.

• Replace all parts and panels before operating.

• Remove doors from your old refrigerator.

• Use nonflammable cleaner.

• Keep flammable materials and vapors, such as gasoline,

away from refrigerator.

• Use two or more people to move and install refrigerator.

• Disconnect power before installing ice maker (on ice maker

kit ready models only).

• Use a sturdy glass when dispensing ice (on some models).

• Do not hit the refrigerator glass doors (on some models).

SAVE THESE INSTRUCTIONS

State of California Proposition 65 Warnings:

WARNING: This product contains one or more chemicals known to the State of California to cause cancer.

WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other

reproductive harm.

Proper Disposal of Your Old Refrigerator

Suffocation Hazard

Remove doors from your old refrigerator.

Failure to do so can result in death or brain damage.

IMPORTANT: Child entrapment and suffocation are not problems

of the past. Junked or abandoned refrigerators are still dangerous

- even if they will sit for "just a few days." Ifyou are getting rid of

your old refrigerator, please follow these instructions to help

prevent accidents.

Before You Throw Away Your Old Refrigerator or Freezer:

• Take off the doors.

• Leave the shelves in place so that children may not easily

climb inside.

important information to know about disposal of

refrigerants:

Dispose of refrigerator in accordance with Federal and Local

regulations. Refrigerants must be evacuated by a licensed,

EPA certified refrigerant technician in accordance with

established procedures.

INSTALLATION INSTRUCTIONS

Excessive Weight Hazard

Use two or more people to move and install

refrigerator.

Failure to do so can result in back or other injury.

Remove the Packaging

Remove tape and glue residue from surfaces before turning

on the refrigerator. Rub a small amount of liquid dish soap

over the adhesive with your fingers. Wipe with warm water

and dry.

Do not use sharp instruments, rubbing alcohol, flammable

fluids, or abrasive cleaners to remove tape or glue. These

products can damage the surface of your refrigerator. For

more information, see "Refrigerator Safety."

• Dispose of/recycle all packaging materials.

When Moving Your Refrigerator:

Your refrigerator is heavy. When moving the refrigerator for

cleaning or service, be sure to cover the floor with

cardboard or hardboard to avoid floor damage. Always pull

the refrigerator straight out when moving it. Do not wiggle or

"walk" the refrigerator when trying to move it, as floor

damage could occur.

Clean Before Using

After you remove all of the packaging materials, clean the inside of

your refrigerator before using it. See the cleaning instructions in

"Refrigerator Care."

important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when

they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping.

Tempered glass is designed to shatter into many small,

pebble-size pieces. This is normal. Glass shelves and covers

are heavy. Use both hands when removing them to avoid

dropping.

I.,()CI:)IIIOI'I: _ '?_'.ii! .............. I

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

To ensure proper ventilation for your refrigerator, allow for a V2"

(1.25 cm) of space on each side and at the top. Allow for a 1"

(2.54 cm) space behind the refrigerator. If your refrigerator has an

ice maker, allow extra space at the back for the water line

connections. When installing your refrigerator next to a fixed wall,

leave a 2" (5.08 cm) minimum space between the refrigerator and

wall to allow the door to swing open.

NOTE: This refrigerator is intended for use in a location where the

temperature ranges from a minimum of 55°F (13°C) to a maximum

of 110°F (43°C). The preferred room temperature range for

optimum performance, which reduces electricity usage and

provides superior cooling, is between 60°F (15°C) and 90°F

(32°C). It is recommended that you do not install the refrigerator

near a heat source, such as an oven or radiator.

1/2" (1.25 cm)

I II I

2" (5.08 cm)

D swe

Depending on the width of your door opening, it may be

necessary to remove the refrigerator doors to move the

refrigerator into your home.

IMPO RTAN1"."

If the refrigerator was previously installed and you are moving

it out of the home, before you begin, turn the refrigerator

control OFF, and unplug the refrigerator or disconnect power.

Remove food and any adjustable door or utility bins from

doors.

Keep the refrigerator doors closed until you are ready to lift

them free from the cabinet. Provide additional support for the

refrigerator door while the hinges are being removed. Do not

depend on the door gasket magnets to hold the door in place

while you are working.

All graphics referenced in the following instructions are

included later in this section after "Final Steps."

TOOLS NEEDED: _e", 3/8",and %" hex head socket wrenches,

Torx®tT25 screwdriver, #2 Phillips screwdriver, and a flat-blade

screwdriver.

Remove Doors and Hinges

1. Unplug refrigerator or disconnect power.

2. Remove the base grille. Grasp the grille firmly and pull it

toward you.

3. Starting with the right-hand side door, remove the parts for the

top hinge as shown in Top Hinge graphic. Lift the refrigerator

door from the bottom hinge pin.

4. Remove the hinge pin cover from the bottom hinge pin and

keep it for later use. See Bottom Hinge graphic.

5. Remove top hinge cover from left-hand side refrigerator door.

6. Remove the parts for the top hinge as shown in Top Hinge

graphic. Lift the left-hand side door from the bottom hinge pin.

NOTE: On some models, remove the hinge pin cover from the

bottom hinge pin and keep it for later use. See Bottom Hinge

graphic.

4. The refrigerator leveling/roller assembly protrudes from each

side of the cabinet base. Remove the three screws attaching

each assembly, and remove the assemblies. See Refrigerator

Leveling/Roller Assembly graphic.

To replace drawer front:

1. Align the leveling/roller assembly with the holes on each side

of the refrigerator cabinet. Using the screws removed, reinstall

the assemblies to the cabinet base. Tighten the screws

completely.

2. Slide the drawer glides out of the freezer compartment. Insert

the screws in the top of the drawer front into the slots in the

drawer brackets. See Drawer Front Replacement graphic.

3. Pull the drawer brackets toward you to position the two

screws in the bottom of the drawer front into the brackets and

completely tighten the four screws. See Drawer Front

Replacement graphic.

4. Replace the base grille.

• Pull open the freezer drawer.

• Align the three clips on the back of the base grille with the

three tabs at the base of the refrigerator.

• Push the base grille in toward the refrigerator until it is

firmly in place.

Replace Doors and Hinges

A. Tab

B. Clip

Assemble the parts for the top hinges as shown in Top Hinge

graphic. Do not tighten the screws completely.

Replace the parts for the bottom hinge as shown in Bottom

Hinge graphic. Tighten screws. Replace the refrigerator door.

NOTE: Provide additional support for the refrigerator door

while the hinges are being moved. Do not depend on the door

gasket magnets to hold the door in place while you are

working.

Align the door so that the bottom of the refrigerator doors

align evenly with the top of the freezer drawer. Tighten all

screws.

4. Replace the top hinge covers.

Remove and Replace Freezer Drawer Front

IMPORTANT: Two people may be required to remove and replace

the freezer drawer. Graphics are included later inthis section.

To remove drawer front:

1. Open the freezer drawer to full extension.

2. Loosen the four screws attaching the drawer glides to the

drawer front. See Drawer Front Removal graphic.

NOTE: Loosen screws three to four turns. Keep the screws in

the drawer front.

3. Lift drawer front upward and off the screws. See Drawer Front

Removal graphic.

t®TORX is a registered trademark of Saturn Fasteners, Inc.

Final Steps

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

1. Plug into a grounded 3 prong outlet.

2. Return all removable parts to doors and drawer and food to

refrigerator and freezer.

Top Hinges

A. Hinge Cover Screw

B. Top Hinge Cover

C. 5/16" Hex-Head Hinge Screws

D. Top Hinge

Bottom Hinges

A. Hinge Pin Cover

B. Bottom Hinge

C. Hinge Screws

Leveling/Roller Assembly

A. Assembly Screws

A. Loosen 4 Door Bracket Screws

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Before you move your refrigerator into its final location, it is

important to make sure you have the proper electrical connection.

Recommended Grounding Method

A 115 volt, 60 Hz., AC only 15- or 20-amp fused, grounded

electrical supply is required. It is recommended that a separate

circuit serving only your refrigerator be provided. Use an outlet

that cannot be turned off by a switch. Do not use an

extension cord.

NOTE: Before performing any type of installation, cleaning, or

removing a light bulb, turn Cooling OFF, and then disconnect the

refrigerator from the electrical source. When you have finished,

reconnect the refrigerator to the electrical source and turn Cooling

ON. See "Using the Control(s)."

A cold water supply with water pressure between 30 and 120 psi

(207 and 827 kPa) is required to operate the water dispenser and

ice maker. Ifyou have questions about your water pressure, call a

licensed, qualified plumber.

Reverse Osmosis Water Supply

IMPORTANT: The pressure of the water supply coming out of a

reverse osmosis system going to the water inlet valve of the

refrigerator needs to be between 30 and 120 psi (207 and

827 kPa).

If a reverse osmosis water filtration system is connected to your

cold water supply, the water pressure to the reverse osmosis

system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

If the water pressure to the reverse osmosis system is less than

40 to 60 psi (276 to 414 kPa):

• Check to see whether the sediment filter in the reverse

osmosis system is blocked. Replace the filter if necessary.

• Allow the storage tank on the reverse osmosis system to refill

after heavy usage. The tank capacity could be too low to keep

up with the requirements of the refrigerator.

If your refrigerator has a water filter, it may further reduce the

water pressure when used in conjunction with a reverse

osmosis system. Remove the water filter. See "Water Filtration

System."

If you have questions about your water pressure, call a licensed,

qualified plumber.

Read all directions before you begin.

IMPORTANT:

• All installations must meet local plumbing code requirements.

• Use copper tubing or Whirlpool supply line, Part Number

8212547RP, and check for leaks.

• Install copper tubing only in areas where the temperatures will

remain above freezing.

TOOLS NEEDED:

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

• Flat-blade screwdriver • V4"Nut driver

• 7Ae"and W' Open-end or two • V4"Drill bit

adjustable wrenches • Cordless drill

NOTE: Your refrigerator dealer has a kit available with a V4"

(6.35 mm) saddle-type shutoff valve, a union, and copper tubing.

Before purchasing, make sure a saddle-type valve complies with

your local plumbing codes. Do not use a piercing-type or 3Ae"

(4.76 mm) saddle valve which reduces water flow and clogs more

easily.

Connect to Water Line

Style 1

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long

enough to clear line of water.

3. Locate a 1/2"to 1V4" (1.25 cm to 3.18 cm) vertical cold water

pipe near the refrigerator.

IMPORTANT:

• Make sure it is a cold water pipe.

• Horizontal pipe will work, but drill on the top side of the

pipe, not the bottom. This will help keep water away from

the drill and normal sediment from collecting in the valve.

4. Determine the length of copper tubing you need. Measure

from the connection on the lower left rear of refrigerator to the

water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use V4"

(6.35 mm) O.D. (outside diameter) copper tubing. Be sure both

ends of copper tubing are cut square.

5. Using a cordless drill, drill a V4"hole in the cold water pipe you

have selected.

A. Cold water pipe

B. Pipe clamp

C. Copper tubing

D. Compression nut

E. Compression sleeve

F. Shutoff valve

G. Packing nut

Fasten the shutoff valve to the cold water pipe with the pipe

clamp. Be sure the outlet end is solidly in the V4"(6.35 mm)

drilled hole in the water pipe and that the washer is under the

pipe clamp. Tighten the packing nut. Tighten the pipe clamp

screws slowly and evenly so washer makes a watertight seal.

Do not overtighten or you may crush the copper tubing.

7. Slip the compression sleeve and compression nut onto the

copper tubing as shown. Insert the end of the tubing into the

outlet end squarely as far as it will go. Screw compression nut

onto outlet end with adjustable wrench. Do not overtighten.

8. Place the free end of the tubing in a container or sink, and turn

ON the main water supply. Flush the tubing until water is clear.

Turn OFF the shutoff valve on the water pipe. Coil the copper

tubing.

Style 2

1. Unplug refrigerator or disconnect power.

2. Remove and discard the black nylon plug from the gray water

tube on the rear of the refrigerator.

3. Thread the provided nut onto the water valve as shown.

NOTE: Tighten the nut by hand. Then tighten it with a wrench

two more turns. Do not overtighten.

Style 2

1. Unplug refrigerator or disconnect power.

2. Remove and discard the black nylon plug from the gray water

tube on the rear of the refrigerator.

3. If the gray water tube supplied with the refrigerator is not long

enough, aV4"x 1/4"(6.35 mm x 6.35 mm) coupling is needed in

order to connect the water tubing to an existing household

water line. Thread the provided nut onto the coupling on the

end of the copper tubing.

NOTE: Tighten the nut by hand. Then tighten it with a wrench

two more turns. Do not overtighten.

I/ III

A.Bulb

B.Nut (provided)

4. Turn shutoff valve ON.

5. Check for leaks. Tighten any nuts or connections (including

connections at the valve) that leak.

Connect to Refrigerator

Style 1

1. Unplug refrigerator or disconnect power.

2. Attach the copper tube to the valve inlet using a compression

nut and sleeve as shown. Tighten the compression nut. Do not

overtighten.

3. Use the tube clamp on the back of the refrigerator to secure

the tubing to the refrigerator as shown. This will help avoid

damage to the tubing when the refrigerator is pushed back

against the wall.

Turn shutoff valve ON.4.

Check for leaks. Tighten any connections (including

connections at the valve) or nuts that leak.

A. Tube clamp

B. Tube clamp screw

C. Copper tubing

D. Compression nut

E. Valve inlet

On models with ice makers, the ice maker is equipped with a

built-in water strainer. If your water conditions require a

second water strainer, install it in the 1/4"(6.35 mm) water line

at either tube connection. Obtain a water strainer from your

nearest appliance dealer.

A B C D E F G

A. Refrigerator water tubing E.Ferrule (purchased)

B. Nut (provided) F Nut (purchased)

C. Bulb G. Household water fine

D. Coupling (provided)

Turn shutoff valve ON.

Check for leaks. Tighten any nuts or connections (including

connections at the valve) that leak.

Complete the Installation

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

1. Plug into a grounded 3 prong outlet.

NOTES:

• Allow 24 hours to produce the first batch of ice. Discard the

first three batches of ice produced. Allow 3 days to completely

fill ice container.

• For models with a water dispenser, flush the water system.

See "Water Dispenser."

PartsIncluded:Refrigeratordoorhandles(2),

Freezerdrawerhandle(1)

ToolsNeeded:Y8"Hex key wrench

Install Door Handles

NOTE: Handle mounting setscrews are preinstalled inside the

handle.

1. Remove the handles from the packaging inside the

refrigerator.

2. Open a refrigerator door. On the opposite door, place the

handle on the shoulder screws with the setscrews facing the

adjacent door.

Install Drawer Handle

1. With the freezer drawer closed, place the handle on the

shoulder screws with the setscrews facing down toward the

floor.

A. Shoulder screw

B. Setscrews inside the handle

2. Firmly push the handle toward the drawer until the handle

base is flush against the drawer.

3. Insert the short end of the hex key into the left-hand hole and

slightly rotate the hex key until it is engaged in the setscrew.

A. Shoulder screws

B. Setscrews inside the handle

3. Firmly push the handle toward the door until the handle base

is flush against the door.

4. While holding the handle, insert the short end of the hex key

into the upper hole and slightly rotate the hex key until it is

engaged inthe setscrew.

Using a clockwise motion tighten the setscrew until the screw

feels tight.

Repeat steps 4 and 5 to fasten the lower setscrew.

IMPORTANT: When the screws feel tight, tighten them an

additional quarter-turn. The handle is not properly installed

without this extra tightening.

Repeat steps 2 through 6 to install the other handle onto the

adjacent refrigerator door.

4. Using a left to right motion tighten the setscrew a quarter-turn

at a time. Repeat until the screw feels tight.

5. Repeat steps 3 and 4 to fasten the right-hand setscrew to the

shoulder screw.

IMPORTANT: When the screws feel tight, tighten them an

additional quarter-turn. The handle is not properly installed

without this extra tightening.

6. Save the hex key and all instructions.

Remove the Handles

1. While holding the handle, insert the short end of the hex key

into asetscrew hole and slightly rotate the hex key until it is

engaged in the setscrew.

2. Using a right to left motion loosen the setscrew a quarter-turn

at a time.

3. Repeat steps 1 and 2 for the other setscrew. Slowly pull the

handle away from the door or drawer.

4. If necessary, use a Phillips screwdriver to remove the shoulder

screws from the door.

-_-% _ _m-_E_ _ _. _ -' "_"_ _

IMPORTANT: To comply with American Disabilities Act (ADA)

guidelines, fully retract the rollers into the cabinet to lower the

refrigerator,

Door Closing

The base grille covers the leveling screws and roller assemblies

located at the bottom of the refrigerator cabinet below the freezer

drawer. Before making adjustments, remove the base grille and

move the refrigerator to its final location.

1. Remove the base grille. Grasp the grille firmly and pull it

toward you.

2. Move the refrigerator to its final location.

NOTE: To allow the refrigerator to roll easier, raise the leveling

legs off the floor by turning the leveling screws

counterclockwise. The front rollers will be touching the floor.

So the doors will close easier, use a V4"hex driver to turn both

leveling screws clockwise. This will raise the front of the

refrigerator tilting it slightly downward to the rear. Turn both

leveling screws the same amount.

NOTE: Having someone push against the top of the

refrigerator takes some weight off the leveling screws. This

makes it easier to turn the screws.

A. Leveling screw

B. Front rofler

Open both doors again to make sure they close as easily as

you like and that they stay closed. If not, tilt the refrigerator

slightly more to the rear by turning both leveling screws to the

right. It may take several more turns.

NOTE: To keep the refrigerator level, you should turn both

leveling screws the same amount.

Replace the base grille.

• Pull open the freezer drawer.

• Align the three clips on the back of the base grille with the

three tabs at the base of the refrigerator.

• Push the base grille in toward the refrigerator until it is

firmly in place.

A. Tab

B. Clip

Door Alignment

If the space between the refrigerator doors and freezer drawer

looks uneven, you can adjust it using the following instructions:

1. Remove the top hinge cover.

2. Loosen the top hinge screws using a 5Ae"socket or wrench.

3. Have someone hold the door in place or put aspacer between

the doors and drawer.

4. Tighten the top hinge screws once the door is inthe desired

location.

5. Replace the top hinge cover.

FILTERS AND

ACCESSORIES

Do not use with water that is microbiologically unsafe or

of unknown quality without adequate disinfection before

or after the system. Systems certified for cyst reduction

may be used on disinfected waters that may contain

filterable cysts.

Water Filter Status Light

The water filter status light on the control panel will help you know

when to order and replace the water filter.

• GOOD - The water filter icon on the control lights up in BLUE.

ORDER a replacement filter - The water filter icon on the

control lights up in YELLOW.

REPLACE the water filter - The water filter icon on the control

lights up in RED and "Replace Filter" will appear on the

display.

EXPIRED - The water filter icon lights up in RED and "Replace

Filter" flashes on the display.

NOTE: If water flow to your water dispenser or ice maker

decreases noticeably, change the filter sooner. The disposable

water filter should be replaced at least every 6 months,

depending on your water quality and usage.

After changing the water filter, reset the status. Press and hold

the WATER FILTER button for 3 seconds. When the system is

reset, the water filter icon will return to its BLUE color and the

words "Replace Filter" will disappear from the display.

Changing the Water Filter

1. Locate the water filter in the top-right corner of the refrigerator

compartment.

2. Lift open the filter cover door. The filter will be released and

then eject as the door is opened.

3. When the door is completely open, pull the filter straight out.

NOTE: There may be some water in the filter. Some spilling

may occur. Use a towel to wipe up any spills.

Take the new filter out of its packaging and remove the covers

from the O-rings. Be sure the O-rings are still in place after the

covers are removed.

5. With the arrow pointing up, align the new filter with the filter

housing and slide it into place. The filter cover door will

automatically begin to close as the new filter is inserted.

6. Close the filter cover door completely in order to snap the filter

into place. You may need to press hard.

7. Flush the water system. See "Water Dispenser" or "Water and

Ice Dispensers."

The air filter reduces the buildup of odors. This helps to maintain a

cleaner environment inside the refrigerator.

On some models, your refrigerator's accessory packet includes

an air filter, which must be installed prior to use. On some models,

the air filter is already installed at the factory.

Installing the Air Filter

Install the air filter behind the vented door, located along the rear

interior wall of the refrigerator compartment.

1. Remove the air filter from its packaging.

NOTE: An air filter status indicator is included with the air filter.

The indicator is not needed for models that display the air filter

status on the control panel.

2. Lift open the vented door.

3. Snap the filter into place.

Air Filter Status Indicator

The control panel displays the Air Filter status.

• GOOD - The air filter icon on the control lights up in BLUE.

• ORDER a replacement - The air filter icon on the control lights

up in YELLOW.

• REPLACE air filter - The air filter icon on the control lights up in

RED and "Replace Filter" will appear.

• EXPIRED - The air filter icon lights up in RED and "Replace

Filter" flashes on the control display.

After replacing the air filter, press and hold the AIR FILTER button

for 3 seconds. The filter icons will turn off. See "Using the

Control(s)." When the system is reset, the air filter icon will return

to its BLUE color and the words "Replace Filter" will disappear

from the display.

NOTE: At any filter status, pressing and holding the AIR FILTER

button for 3 seconds will reset the air filter status to Good and the

air filter icon will turn off.

Replacing the Air Filter

The disposable air filter should be replaced every 6 months, or

when the status indicator air filter icon turns on and starts flashing

when the refrigerator door is opened.

To order a replacement air filter, contact us. See "Accessories."

1. Remove the used air filter by squeezing in on the side tabs.

2. Install the new air filter and reset the status indicator using the

instructions in the previous section.

The produce preserver absorbs ethylene, to slow the ripening

process of many produce items. As a result, certain produce

items will stay fresh longer.

Ethylene production and sensitivity varies depending on the type

of fruit or vegetable. To preserve freshness, it is best to separate

produce with sensitivity to ethylene from fruits that produce

moderate to high amounts of ethylene.

Apples

Asparagus

Berries

Broccoli

Cantaloupe

Carrots

Citrus Fruit

Grapes

Lettuce

Pears

Spinach

Sensitivity to

Ethylene

High

Med.

Low

High

Med.

Low

Med.

Low

High

Ethylene

Production

Very High

Very Low

Low

Very Low

High

Very Low

Very High

Very Low

Installing the Produce Preserver

CAUTION: IRRITANT

MAY IRRITATE EYES AND SKIN. DANGEROUS FUMES

FORM WHEN MIXED WITH OTHER PRODUCTS.

Do not mix with cleaning products containing ammonia,

bleach or acids. Do not get in eyes, on skin or clothing. Do

not breathe dust. Keep out of reach of children.

FIRST AID TREATMENT: Contains potassium

permanganate. If swallowed, call a Poison Control Center or

doctor immediately. Do not induce vomiting. If in eyes, rinse

with water for 15 minutes. If on skin, rinse with water.

1. Find the Produce Preserver housing inside the refrigerator.

The following accessories are available for your refrigerator. To

order, contact us and ask for the part numbers.

In the U.S.A., visit our web page www.kitchenaid.com/

accessories or call 1-800-901-2042.

In Canada, visit our web page www.whirlpoolparts.ca

or call 1-800-807-6777.

2. Open the housing by pulling up and out on the back.

3. Remove the FreshFIow TM Produce Preserver pouches from

the packaging and place them into the housing.

NOTE: For best performance, always use two pouches.

4. Place the Produce Preserver housing onto the tab located on

the back wall of the crisper drawer.

Installing the Status Indicator

The produce preserver comes with a status indicator, which

should be activated and installed at the same time the pouches

are installed.

1. Place the indicator face-down on a firm, flat surface.

2. Apply pressure to the bubble on the back of the indicator until

the bubble pops, to activate the indicator.

3. Slide open the cap on the top of the produce preserver

housing.

4. Place the indicator in the top of the housing, facing outward.

5. Slide the cap closed, and check that the indicator is visible

through the rectangular hole in the cap.

NOTE: The cap will not easily close if the indicator's bubble

has not been popped.

Replacing the Produce Preserver

The disposable pouches should be replaced every 6 months or

when the status indicator changes completely from white to red.

To order replacements, contact us. See "Accessories" for

information on ordering.

1. Remove the used pouches from the produce preserver

housing.

2. Remove the used status indicator.

3. Install the replacement pouches and status indicator using the

instructions in the previous sections.

affresh TMtStainless Steel Cleaner:

Order Part #W10355016

affresh TMtStainless Steel Wipes:

Order Part #W10355049

affresh TMtKitchen & Appliance Cleaner:

Order Part #W10355010

Water Filter:

Order Part # W10295370A or FILTER1

Air Filter:

Order Part #W10311524 or AIR1

Produce Preserver:

Order Part #W10346771A or FRESH1

Water Filter, Air Filter and Produce Preserver Bundle Pack:

Order Part #W10443987BL

REFRIGERATOR USE

_7 ............

There are two refrigerator compartment doors. The doors can be

opened and closed either separately or together.

There is a vertically-hinged seal on the left refrigerator door.

• When the left side door is opened, the hinged seal

automatically folds inward so that it is out of the way.

• When both doors are closed, the hinged seal automatically

forms a seal between the two doors.

A. Hinged seal

1-TM AFFRESH is a Trademark of Whirlpool, U.S.A.

IMPC RTANT:

• Wait 24 hours for your refrigerator to cool completely before

adding food. If you add food before the refrigerator has cooled

completely, your food may spoil.

NOTE: Adjusting the refrigerator and freezer temperature

controls to a colder than recommended setting will not cool

the compartments any faster.

The recommended setting should be correct for normal

household refrigerator use. The controls are set correctly

when milk or juice is as cold as you like and when ice cream is

firm.

NOTE: Areas such as a garage or porch, may experience

warmer or colder temperatures and higher humidity than

inside the home. You may need to adjust the temperature

away from the recommended set points to accommodate for

these conditions.

If the temperature is too warm or too cold in the refrigerator or

freezer, before adjusting the controls, first check the air vents

located in the refrigerator and freezer compartments to be

sure they are not blocked by food items.

Control Panel

The control panel is located inside the refrigerator compartment.

This control operates both the refrigerator and freezer

compartments.

Cooling [_

Replace Filter Off Replace Filter

>Colder _ Colder

• .... =-, .....

Freezer Temp Air Fi(ter Max Cool Moisture Control Water Filter Fridge Temp

The control panel will display the Home Screen, as shown, when

either refrigerator door is opened.

Adjusting the Temperature

If you need to adjust the temperature in either the refrigerator or

freezer compartment, use the settings listed in the following chart

as a guide.

• Press either the FREEZER TEMP or FRIDGE TEMP button to

select the desired temperature setting from (1 box [least cold]

to 5 boxes [coldest]).

NOTE: Except when starting the refrigerator, do not adjust the

control more than one setting at a time. Wait 24 hours between

adjustments for the temperature to stabilize.

CONDITION/REASON: ADJUSTMENT:

REFRIGERATOR too warm FRIDGE TEMP one

setting (box) more

FREEZER too warm/too little ice FREEZER TEMP one

setting (box) more

REFRIGERATOR too cold FRIDGE TEMP one

setting (box)less

FREEZER too cold FREEZER TEMP one

setting (box)less

Cooling Off/On

Your refrigerator and freezer will not cool and water will not

dispense when cooling is turned off.

• To turn cooling off, press and hold both the MAX COOL and

MOISTURE CONTROL buttons, at the same time, for

3 seconds. When cooling is off, "Cooling Off" will appear on

the display screen.

To turn cooling back on, press and hold both the MAX COOL

and MOISTURE CONTROL buttons, at the same time, for

3 seconds. When cooling is on, "Cooling Off" will disappear

and the previously selected settings will appear on the display

screen.

Cooling

off

Temperature Control

For your convenience, the temperature control is preset at the

factory. When you first install your refrigerator, make sure the

control is still set to the recommended setting as shown.

Recommended Setting (3 lit boxes)

Additional Features

Max Cool

The Max Cool feature assists during times of high refrigerator use,

full grocery loads or temporarily warm room temperatures.

• Press MAX COOL to set the freezer and refrigerator to the

coldest temperature settings. Press MAX COOL again to

return to the selected temperature set point.

NOTES:

The Max Cool icon will be illuminated while the refrigerator

is in Max Cool mode.The displayed compartment

temperature settings will not change.

The Max Cool feature will turn off automatically after

24 hours.

--€*

Moisture Control

The moisture control feature turns on a heater to help reduce

moisture on the door hinge seal. Use in humid environments or

when you notice moisture on the door hinge seal. The refrigerator

uses more energy when Moisture Control is on.

• To turn on the Moisture Control feature, press and hold

MOISTURE CONTROL for 3 seconds.

• To turn off the Moisture Control feature, press and hold

MOISTURE CONTROL for 3 seconds.

Door Open Alarm

• The Door Open icon lights up when a door has been open for

5 minutes and cooling is on. An alert tone will sound three

times, and the Door Open icon will flash seven times. This

pattern will repeat every 2 minutes until all the doors are

closed completely. The feature then resets and will reactivate

when a door is left open again for 5 minutes.

NOTES:

To mute the audible alarm while keeping the doors open,

such as while cleaning the inside of the refrigerator, press

any button on the control panel. The alarm sound will be

temporarily turned off, but the Door Open icon will still be

displayed on the dispenser control panel.

• All doors must be completely closed to turn off the Door

Open icon.

Sabbath Mode

Sabbath mode is designed for those whose religious observances

require turning off the lights.

In Sabbath Mode the temperature set points remain unchanged,

but the interior and dispenser lights turn off, all sounds and alarms

are disabled and the dispenser screen backlight turns off.

• To turn on Sabbath Mode, press and hold both FREEZER

TEMP and FRIDGE TEMP at the same time for 3 seconds.

After 3 seconds, an "engage" tone will sound and the icons on

the control panel display will flash and then disappear.

NOTE: You must close the doors to turn off the lights. The

lights will remain off while the refrigerator is in Sabbath mode.

To turn off Sabbath Mode, press and hold both FREEZER

TEMP and FRIDGE TEMP at the same time for 3 seconds.

After 3 seconds, an "disengage" tone will sound and the

control panel will display the normal screen.

NOTE: After turning off Sabbath Mode, you must first close

the doors to turn ON the lights. Then the lights will function

normally.

NOTES:

• Sabbath mode does not disable the water dispenser or the ice

maker. To turn off the ice maker, see "Ice Maker."

• If a power failure occurs or you unplug the refrigerator while it

is in Sabbath mode, it will take 10 minutes for the cooling

system to resume when power is restored.

Water Filter Status Light and Reset

The filter reset control allows you to restart the water filter status

tracking feature each time you replace the water filter. See "Water

Filtration System."

• Press and hold WATER FILTER for 3 seconds, to reset the

water filter status to Good. The Water Filter icon will turn blue.

Air Filter Status Light and Reset

The filter reset control allows you to restart the air filter status

tracking feature each time you replace the air filter. See "Install Air

Filter."

• Press and hold AIR FILTER for 3 seconds, to reset the air filter

status to Good. The Air Filter icon will turn blue.

IMPO RTANT:

• Allow 3 hours for the refrigerator to cool down and chill water.

• Allow 24 hours to produce the first batch of ice. Discard the

first three batches of ice produced.

Flush the Water System

Air in the water dispensing system can cause the water dispenser

to drip. After connecting the refrigerator to a water source or

replacing the water filter, flush the water system.

Flushing the water dispensing system, forces air from the water

line and filter and prepares the water filter for use. Additional

flushing may be required insome households.

NOTE: As air is cleared from the system, water may spurt out of

the dispenser.

1. Using a sturdy container, depress and hold the water

dispenser paddle for 5 seconds.

2. Release the dispenser paddle for 5 seconds. Repeat steps 1

and 2 until water begins to flow.

3. Once water begins to flow, continue depressing and releasing

the dispenser pad (5 seconds on, 5 seconds off) until atotal of

4 gal. (15 L) has been dispensed.

Dispense Water

1. Hold a container under the dispenser spout while pressing the

dispenser pad.

2. Release the dispenser pad to stop dispensing.

Ice h/lake::

IMPORTANT: For models with a water filter, after connecting the

refrigerator to a water source or replacing the water filter, fill and

discard three full containers of ice to prepare the water filter for

use.

Turning the Ice Maker On/Off

Toturn the ice maker ON, simply lower the wire shutoff arm.

To manually turn the ice maker OFF, lift the wire shutoff arm to the

OFF (arm up) position and listen for the click.

NOTE: Your ice maker has an automatic shutoff. As ice is made,

the ice cubes will fill the ice storage bin and the ice cubes will

raise the wire shutoff arm to the OFF (arm up) position. Do not

force the wire shutoff arm up or down.

IceStorageBin

Wash the ice storage bin with mild soap and warm water.

Slide the ice storage bin under the ice maker, and push it

toward the back as far as it will go.

Lower the arm on the ice maker to the "on" position.

NOTE: It usually takes approximately 24 hours for the ice

maker to begin producing ice. You may notice the ice has an

"off-taste." If so, discard the first three batches of ice

produced. After that the "off-taste" should be gone.

Ice Production Rate

• The ice maker should produce approximately 8 to 12 batches

of ice in a 24-hour period. Allow 3 days to completely fill the

ice container.

• To increase ice production, lower the freezer and refrigerator

temperature. See "Using the Control(s)." Wait 24 hours

between adjustments.

Remember

The quality of your ice will be only as good as the quality of the

water supplied to your ice maker. Avoid connecting the ice

maker to a softened water supply. Water softener chemicals

(such as salt) can damage parts of the ice maker and lead to

poor quality ice. If asoftened water supply cannot be avoided,

make sure the water softener is operating properly and is well

maintained.

• Do not use anything sharp to break up the ice in the bin. This

can cause damage to the ice storage bin and the dispenser

mechanism.

• Do not store anything on top of or in the ice maker or ice

storage bin.

REFRIGERATOR

FEATURES

NOTE: Your model may have some or all of these features.

Important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when

they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping.

Tempered glass is designed to shatter into many small,

pebble-size pieces. This is normal. Glass shelves and covers

are heavy. Use both hands when removing them to avoid

dropping.

To replace a shelf:

1. Slide the back of the shelf into the track in the wall of the

cabinet.

2. Guide the front of the shelf into the shelf track. Be sure to slide

the shelf in all the way.

Fold Away Shelf (on some models)

To retract the fold away shelf:

• Retract the fold away section of the shelf by holding the front

of the shelf with one hand and lifting up on the center front of

the shelf. Then push back and down on the shelf until it slides

beneath the back section of the shelf.

To replace the fold away shelf:

• Replace the fold away section of the shelf by holding the front

of the shelf with one hand and pulling the center of the shelf

until the fold away section is returned to its full shelf position.

Pantry Drawer

To remove and replace the pantry drawer:

1. Slide pantry drawer out to the stop.

2. Lift front of pantry drawer with one hand while supporting

bottom of drawer with other hand. Slide drawer out the rest of

the way.

3. Replace the drawer by sliding it back in fully past the drawer

stop.

Pantry Drawer Cover

To remove and replace the pantry drawer cover:

1. Remove the pantry drawer.

2. From underneath, push up on the glass cover and pull it out.

3. Replace the pantry drawer cover by lowering it into place.

4. Replace the pantry drawer.

The shelves in your refrigerator are adjustable to match your

individual storage needs.

Glass Shelves

To remove a shelf:

1. Remove items from the shelf.

2. Slide the shelf straight out to the stop.

3. Depending on your model, lift the back or front of the shelf

past the stop. Pull the shelf out the rest of the way.

Pantry Drawer Control

The amount of air flowing through the pantry drawer affects the

temperature inside the drawer.

The airflow control is located on the left side of the pantry drawer.

To adjust the airflow:

• Colder - Slide the control forward, toward the front of the

pantry drawer. The airflow is open.

• Cold - Slide the control all the way toward the rear of the

pantry drawer. The airflow is closed, as shown.

Crisper Drawers

To remove and replace the crisper drawer:

1. Slide the crisper drawer straight out to the stop. Lift the front

and slide the drawer out the rest of the way.

2. Replace the drawer by sliding the drawer in fully past the stop.

• Leafy vegetables: Wash in cold water, drain and trim or tear off

bruised and discolored areas. Place in plastic bag or plastic

container and store in crisper.

DOOR FEATURES

NOTE: Your model may have some or all of these features.

To remove and replace the condiment bins:

1. Tilt the bin by grabbing it and pulling outward.

2. Remove the bin by grabbing it and lifting it upward off the

glides.

3. Replace the bin by sliding it back onto the glides and then

push it closed.

Crisper Cover

To remove and replace the glass crisper cover:

1. Pull the glass straight out.

2. Replace the glass by pushing it straight in.

Crisper Humidity Control (on some models)

You can control the amount of humidity in the moisture-sealed

crisper. Adjust the control to any setting between LOW and HIGH.

LOW (open) lets moist air out of the crisper for best storage of

fruits and vegetables with skins.

• Fruit: Wash, let dry and store in refrigerator in plastic bag or

crisper. Do not wash or hull berries until they are ready to use.

Sort and keep berries in original container in crisper, or store in

a loosely closed paper bag on a refrigerator shelf.

• Vegetables with skins: Place in plastic bag or plastic container

and store in crisper.

HIGH (closed) keeps moist air in the crisper for best storage of

fresh, leafy vegetables.

To remove and replace the fresh bin:

1. Open the bin by grabbing the top center lip of the bin and

tilting the bin outward.

2. Remove the bin by grabbing both sides of the bin and lifting

the bin upward off the glides.

3. Replace the bin by sliding it back into its tilted position on the

glides and then push it closed.

To remove and replace the half-height bin:

1. Tilt the bin by grabbing it and pulling outward.

2. Remove the bin by grabbing it and lifting it upward off the

glides.

3. Replace the bin by sliding it back onto the glides and then

push it closed.

REFRIGERATOR CARE

Explosion Hazard

Use nonflammable cleaner.

Failure to do so can result in death, explosion, or fire.

Both the refrigerator and freezer sections defrost automatically.

However, clean both sections about once a month to avoid

buildup of odors. Wipe up spills immediately.

IMPO RTANT:

Because air circulates between both sections, any odors

formed in one section will transfer to the other. You must

thoroughly clean both sections to eliminate odors. To avoid

odor transfer and drying out of food, wrap or cover foods

tightly.

For stainless steel models, stainless steel is corrosion-

resistant and not corrosion-proof. To help avoid corrosion of

your stainless steel, keep your surfaces clean by using the

following cleaning instructions.

To Clean Your Refrigerator:

NOTE: Do not use abrasive or harsh cleaners such as window

sprays, scouring cleansers, flammable fluids, muriatic acid,

cleaning waxes, concentrated detergents, bleaches or cleansers

containing petroleum products on exterior surfaces (doors and

cabinet), plastic parts, interior and door liners or gaskets. Do not

use paper towels, scouring pads, or other harsh cleaning tools.

1. Unplug refrigerator or disconnect power.

2. Hand wash, rinse, and dry removable parts and interior

surfaces thoroughly. Use a clean sponge or soft cloth and a

mild detergent in warm water.

3. Clean the exterior surfaces.

Painted metal: Wash painted metal exteriors with a clean,

soft cloth or sponge and a mild detergent in warm water.

Rinse surfaces with clean, warm water and dry immediately to

avoid water spots.

Stainless steel: Wash stainless steel surfaces with a clean,

soft cloth or sponge and a mild detergent in warm water.

Rinse surfaces with clean, warm water and dry immediately to

avoid water spots.

NOTE: When cleaning stainless steel, always wipe in the

direction of the grain to avoid cross-grain scratching.

There is no need for routine condenser cleaning in normal

home operating environments. If the environment is

particularly greasy or dusty, or there is significant pet traffic in

the home, the condenser should be cleaned every 2 to

3 months to ensure maximum efficiency.

If you need to clean the condenser:

• Remove the base grille.

• Use a vacuum cleaner with a soft brush to clean the grille,

the open areas behind the grille and the front surface area

of the condenser.

• Replace the base grille when finished.

Plug in refrigerator or reconnect power.

IMPORTANT:

• Not all appliance bulbs will fit your refrigerator. Be sure to

replace the bulb with an appliance bulb of the same size,

shape and wattage.

• To ensure optimum refrigerator performance, replace light

bulbs as soon as they burn out.

Refrigerator Compartment Light

The lighting located at the top of the refrigerator compartment

never needs to be replaced. Ifthe lights do not illuminate when

the door is opened, call for assistance or service. In the U.S.A.,

call 1-800-253-1301. In Canada, call 1-800-807-6777.

Freezer Compartment Light (on some models)

Unplug the refrigerator or disconnect power.

Remove the light shield (on some models).

• Top of the freezer compartment - Slide the light shield

toward the back of the compartment to release it from the

light assembly.

3. Replace the burned-out bulb with an appliance bulb(s) no

greater than 25 watts.

4. Replace the light shield.

5. Plug in refrigerator or reconnect power.

TROUBLESHOOTING

First try the solutions suggested here or visit our website and reference FAQs (Frequently Asked Questions)

to possibly avoid the cost of a service call.

In the U.S.A., www.kitchenaid.com In Canada, www.kitchenaid.ca

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

The refrigerator will not

operate

Check electrical supply Plug the power cord into a grounded 3 prong outlet.

Do not use an extension cord.

Make sure there is power to the outlet. Plug in a lamp to see if

the outlet is working.

Reset atripped circuit breaker. Replace any blown fuses.

NOTE: If problems continue, contact an electrician.

Check controls Make sure the controls are turned on. See "Using the

Controls."

New installation Allow 24 hours following installation for the refrigerator to cool

completely.

NOTE: Adjusting the temperature controls to the coldest

setting will not cool either compartment quicker.

The motor seems to run too High efficiency compressor and fans This is normal. Larger, more efficient refrigerators run longer.

much ................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................

The room or outdoor temperature is It is normal for the refrigerator to work longer under these

hot conditions. For optimum performance, place the refrigerator

in an indoor, temperature controlled environment. See

"Location Requirements."

A large amount of warm food has been Warm food will cause the refrigerator to run longer until the air

recently added cools to the desired temperature.

The door(s) are opened too frequently Warm air entering the refrigerator causes it to run more. Open

or for too long the door less often.

The refrigerator door or freezer drawer Make sure the refrigerator is level. See "Door Closing and

is ajar Door Alignment." Keep food and containers from blocking the

door.

The refrigerator control is set too cold Adjust the refrigerator control to a less cold setting until the

refrigerator temperature is as desired. See "Using the

Controls."

The door or drawer gasket is dirty, Clean or change the gasket. Leaks in the door seal will cause

worn, or cracked the refrigerator to run longer in order to maintain desired

temperatures.

The lights do not work A light bulb is loose in the socket or

burned out

Tighten or replace the light bulb. See "Changing the Light

Bulbs."

The dispenser light is set to OFF On some models, the dispenser light will operate only when a

dispenser paddle is pressed. If you want the dispenser light to

stay on continuously, see "Water Dispenser."

The control is set to Sabbath Mode (on Turn off Sabbath Mode. See "Using the Controls."

some models)

The refrigerator seems The compressor in your new refrigerator regulates

noisy temperature more efficiently while using less energy, and

Below are listed some normal operates quietly. Due to the reduction in operating noise you

sounds with explanations, may notice more intermittent noises.

Sound of the compressor High efficiency compressor and fans This is normal. Larger, more efficient

running longer than expected refrigerators run longer.

Pulsating/Whirring Fans/compressor adjusting to optimize performance during This is normal

normal compressor operation

Popping Contraction/expansion of inside walls, especially during initial This is normal

cool-down

Hissing/Dripping Flow of refrigerant, or flow of oil in the compressor This is normal

Vibration The refrigerator may not be steady Adjust the leveling screws and lower

the leveling foot firmly against the floor.

See "Door Closing and Door

Alignment."

Rattling/Banging Movement of the water lines against the refrigerator cabinet, Move excess water line away from the

or of items placed on top of the refrigerator cabinet refrigerator cabinet or fasten excess

tubing to the cabinet. See "Connect

the Water Supply," or remove items

from the top of the refrigerator.

Sizzling Water dripping on the heater during defrost cycle This is normal

Water running/Gurgling May be heard when ice melts during the defrost cycle and This is normal

water runs into the drain pan

Buzzing Heard when the water valve opens to fill the ice maker This is normal

Creaking/Cracking May be heard as ice is being ejected from the ice maker mold This is normal

Ker-plunk May be heard when the ice falls into the ice storage bin This is normal

Temperature is too warm The refrigerator has just been installed Allow 24 hours following installation for the refrigerator to cool

completely.

Cooling is turned off Turn on cooling. See "Using the Controls."

The controls are not set correctly for Adjust the controls a setting colder. Check the temperature in

the surrounding conditions 24 hours. See "Using the Control(s)."

The door(s) are opened often or not Allows warm air to enter refrigerator. Minimize door openings

closed completely and keep doors fully closed.

A large load of food was recently Allow several hours for refrigerator to return to normal

added temperature.

Temperature is too cold in The refrigerator air vent(s) are blocked If the air vent located in the top, left, rear corner of the

the refrigerator/crisper refrigerator compartment is blocked by items placed directly

in front of it, the refrigerator will get too cold. Move items

away from the air vent.

The controls are not set correctly for Adjust the controls a setting warmer. Check the temperature

the surrounding conditions in 24 hours. See "Using the Controls."

The ice storage bin is not in the correct See "Ice Maker."

position

Temperature is too cold in The control is not set correctly for the Adjust the control setting. See "Refrigerator Features."

the pantry drawers items stored in drawer

There is interior moisture The room is humid A humid environment contributes to moisture buildup.

buildup ...............................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................

NOTE: Some moisture The door(s) are opened often or not Allows humid air to enter the refrigerator. Minimize door

buildup is normal, closed completely openings and close doors completely.

The door is blocked open Move food packages away from door.

A bin or shelf is in the way Push bin or shelf back into the correct position.

Storing liquid in open containers This adds humidity to the refrigerator interior. Keep all

containers tightly covered.

There is frost/ice buildup in The doors are opened often or left Minimize door openings and keep doors fully closed.

the freezer compartment open

Poor door seal Ensure door seals are making full contact with the refrigerator

cabinet to allow for an adequate seal.

Temperature controls are not set See "Using the Controls" for recommended temperature

correctly settings.

The ice maker is not

producing ice or is not

producing enough ice

The refrigerator is not connected to a Connect refrigerator to water supply and turn water shutoff

water supply or the water supply valve fully open.

shutoff valve is not turned on

There is a kink in the water source line A kink in the line can reduce water flow. Straighten the water

source line.

The ice maker is not turned on Make sure the ice maker is on. See "Ice Maker."

The refrigerator has just been installed Wait 24 hours after ice maker installation for ice production to

begin. Wait 3 days for full ice production.

The refrigerator door is not closed Close the door firmly. If it does not close completely, see "The

completely doors will not close completely."

A large amount of ice was recently Allow 24 hours for ice maker to produce more ice.

removed

An ice cube is jammed in the ice maker Remove ice from the ejector arm with a plastic utensil.

ejector arm NOTE: On some models, press the lever which opens the ice

maker door to access the ejector arm.

A water filter is installed on the Remove the water filter and operate the ice maker. If ice

refrigerator volume improves, then the filter may be clogged or incorrectly

installed. Replace filter or reinstall it correctly.

A reverse osmosis water filtration This can decrease water pressure. See "Water Supply

system is connected to your cold Requirements."

water supply

The ice cubes are hollow or The water shutoff valve is not fully Turn the water shutoff valve fully open.

small open

NOTE: This is an indication of

low water pressure. There is a kink in the water source line A kink in the line can reduce water flow. Straighten the water

source line.

A water filter is installed on the Remove filter and operate ice maker. If ice quality improves,

refrigerator then the filter may be clogged or incorrectly installed. Replace

filter or reinstall it correctly.

A reverse osmosis water filtration This can decrease water pressure. See "Water Supply

system is connected to your cold Requirements."

water supply

Questions remain regarding water Call a licensed, qualified plumber.

pressure

Off-taste, odor or gray color Recently installed or replaced Discard the ice and wash the ice storage bin. Flush the water

in the ice or water plumbing connections. New plumbing system with 4 gal. (15 L) of water. Allow 24 hours for the ice

connections can cause discolored or maker to make new ice, and discard the first 3 batches of ice

off-flavored ice and water, produced.

The ice has been stored too long Discard ice. Wash ice storage bin. Allow 24 hours for ice

maker to make new ice.

The water has been stored too long Dispense at least 1 qt (1 L) of water per week to maintain a

fresh supply.

Odor from stored food has transferred Use airtight, moisture proof packaging to store food.

to the ice

There are minerals (such as sulfur) in A water filter may need to be installed to remove the minerals.

the water

There is a water filter installed on the Gray or dark discoloration in ice may indicate that the water

refrigerator filtration system needs additional flushing. Flush the water

system after installing and before using a new water filter. See

"Water Dispenser" for water filter flushing instructions.

The water filter needs to be replaced Replace the disposable water filter at least every 6 months or

when indicated. See "Water Filtration System."

The water dispenser will The refrigerator is not connected to a Connect the refrigerator to the water supply and turn the

not operate properly water supply or the water supply water shutoff valve fully open.

shutoff valve is not turned on

There is a kink in the water source line A kink in the water line can reduce water flow from the water

dispenser and result in hollow or irregular shaped ice.

Straighten the water source line.

The refrigerator has just been installed Flush and fill the water system. See "Water Dispenser."

The water pressure to the house is not The water pressure to the house determines the flow from the

at or above 30 psi (207 kPa) dispenser. See "Water Supply Requirements."

A reverse osmosis water filtration A reverse osmosis water filtration system can decrease water

system is connected to your cold pressure. See "Water Supply Requirements."

water supply

A water filter is installed on the Remove filter and operate dispenser. If water flow increases,

refrigerator the water filter may be clogged or incorrectly installed.

Replace filter or reinstall it correctly.

The refrigerator door is not closed Close the door firmly. If it does not close completely, see "The

completely (on some models) doors will not close completely."

The refrigerator doors were recently Make sure the water dispenser wire/tube assembly has been

removed properly reconnected at the top of the refrigerator door.

See "Remove and Replace Refrigerator Doors and Drawer

Front."

La page charge ...

KitchenAid KFFS20EYBL02 Le manuel du propriétaire

Marque: KitchenAid

Modèle: KFFS20EYBL02

Catégorie: Frigos

Taper: Le manuel du propriétaire

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: KitchenAid KFFS20EYBL02 Owner's manual

KitchenAid KFFS20EYBL02 Le manuel du propriétaire

Ce manuel convient également à

KitchenAid KFFS20EYBL02 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents