IKEA IH5303SS0 Guide d'installation

Catégorie
Hottes
Taper
Guide d'installation

Ce manuel convient également à

|KEA ®
90 CM (35 2/5")WALL-MOUNT
CANOPY RANGE HOOD
HOTTEDE CUlSlNII:RE POUR
MONTAGE MURAL 90 CM (35 2/5")
Table of Contents/Table des matieres ............................................................................. 2
IMPORTANT: READ AND SAVE THESE INSTRUCTIONS.
FOR RESIDENTIAL USE ONLY.
IMPORTANT : LIRE ET CONSERVER CES INSTRUCTIONS.
POUR UTILISATION RESIDENTIELLE UNIQUEMENT.
IMPORTANT:
Installer: Leave installation instructions with the homeowner.
Homeowner: Keep installation instructions for future reference.
Save installation instructions for local electrical inspector's use.
IMPORTANT :
Installateur : Remettre les instructions d'installation au propri_taire.
Propri6taire : Conserver les instructions d'installation pour r_f@ence ult@ieure.
Conserver les instructions d'installation pour consultation par I'inspecteur local des installations _lectriques.
W10018030A
TABLEOF CONTENTS
RANGE HOOD SAFETY ................................................................. 2
INSTALLATION REQUIREMENTS ................................................ 4
Tools and Parts ............................................................................ 4
Location Requirements ................................................................ 4
Venting Requirements .................................................................. 5
Electrical Requirements ............................................................... 6
INSTALLATION INSTRUCTIONS .................................................. 7
Prepare Location .......................................................................... 7
Install Range Hood ....................................................................... 9
Connect Vent System (for vented installations only) ................... 9
Make Electrical Connection ......................................................... 9
Complete Installation ................................................................. 10
Install Filters ................................................................................ 10
Check Operation ........................................................................ 10
RANGE HOOD USE ...................................................................... 10
Operation .................................................................................... 10
RANGE HOOD CARE ................................................................... 11
Cleaning and Maintenance ........................................................ 11
WIRING DIAGRAM ...................................................................... 12
ASSISTANCE OR SERVICE ......................................................... 13
In the U.S.A................................................................................ 13
In Canada ................................................................................... 13
WAR RANTY .................................................................................. 13
TABLEDESMATIERES
SECURITE DE LA HOTTE DE CUlSINIERE ............................... 15
EXIGENCES D'INSTALLATION ................................................... 17
Outillage et pieces ...................................................................... 17
Exigences d'emplacement ......................................................... 17
Exigences concernant I'evacuation ........................................... 18
Specifications electriques .......................................................... 20
INSTRUCTIONS D'INSTALLATION ............................................. 20
Preparation de I'emplacement ................................................... 20
Installation de la hotte ................................................................ 22
Installation du conduit d'evacuation
(pour installations avec decharge &I'exterieur uniquement) .....22
Raccordement electrique ........................................................... 23
Achever I'installation .................................................................. 23
Installation des filtres .................................................................. 24
Contr61e du fonctionnement ...................................................... 24
UTILISATION DE LA HOTTE DE CUlSINIF:RE ........................... 24
Fonctionnement ......................................................................... 24
ENTRETIEN DE LA HOTTE DE CUlSINIF:RE ............................. 24
Nettoyage et entretien ................................................................ 24
SCHEMA DE C,&,BLAGE .............................................................. 26
ASSISTANCE OU SERVICE ......................................................... 27
GARANTIE ..................................................................................... 27
RANGE HOOD SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."
These words mean:
You can be killed or seriously injured if you don't immediately
follow instructions.
You can be killed or seriously injured if you don't follow
instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
2
iMPORTANT SAFETY iNSTRUCTiONS
WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK, OR INJURY TO PERSONS, OBSERVE THE
FOLLOWING:
[] Use this unit only in the manner intended by the
manufacturer. If you have questions, contact the
manufacturer.
[] Before servicing or cleaning the unit, switch the power off at
the service panel disconnecting means to prevent power
from being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten a
prominent warning device, such as a tag, to the service
panel.
[] Installation work and electrical wiring must be done by
qualified person(s) in accordance with all applicable codes
& standards, including fire-rated construction.
[] Sufficient air is needed for proper combustion and
exhausting of gases through the flue (chimney) of fuel
burning equipment to prevent backdrafting. Follow the
heating equipment manufacturer's guideline and safety
standards such as those published by the National Fire
Protection Association (NFPA), the American Society for
Heating, Refrigeration and Air Conditioning Engineers
(ASHRAE), and the local code authorities.
[] When cutting or drilling into wall or ceiling; do not damage
electrical wiring and other utilities.
[] Ducted systems must always be vented outdoors.
CAUTION: For general ventilating use only. Do not use
to exhaust hazardous or explosive materials and vapors.
CAUTION: To reduce risk of fire and to properly exhaust
air, be sure to duct air outside - do not vent exhaust air into
spaces within walls ceilings, attics, crawl spaces, or
garages.
WARNING: TO REDUCE THE RISK OF FIRE, USE ONLY
METAL DUCTWORK.
WARNING: TO REDUCE THE RISK OF A RANGE TOP
GREASE FIRE:
[] Never leave the surface units unattended at high settings.
Boilovers cause smoking and greasy spillovers that may
ignite. Heat oils slowly on low or medium settings.
[] Always turn hood ON when cooking at high heat or when
flambeing food (i.e. Crepes Suzette, Cherries Jubilee,
Peppercorn Beef Flamb_).
[] Clean ventilating fans frequently. Grease should not be
allowed to accumulate on fan or filter.
[] Use proper pan size. Always use cookware appropriate for
the size of the surface element.
WARNING: TO REDUCE THE RISK OF INJURY TO
PERSONS IN THE EVENT OF A RANGE TOP GREASE
FIRE, OBSERVE THE FOLLOWING: a
[] SMOTHER FLAMES with a close fitting lid, cookie sheet, or
other metal tray, then turn off the gas burner or electric
element. BE CAREFUL TO PREVENT BURNS. If the
flames do not go out immediately, EVACUATE AND CALL
THE FIRE DEPARTMENT.
[] NEVER PICK UP A FLAMING PAN - you may be burned.
[] DO NOT USE WATER, including wet dishcloths or towels -
a violent steam explosion will result.
[] Use an extinguisher ONLY if:
- You know you have a class ABC extinguisher, and you
already know how to operate it.
- The fire is small and contained in the area where it
started.
- The fire department is being called.
- You can fight the fire with your back to an exit.
aBased on "Kitchen Fire Safety Tips" published by NFPA.
[] WARNING: To reduce the risk of fire or electrical shock,
do not use this fan with any solid-state speed control
device.
SAVE THESE INSTRUCTIONS
INSTALLATIONREQUIREMENTS
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
Tools needed
Level
Drill with 11¼'' (3 cm), 3/8"(9.5 mm), 7/64"(2.75 mm) and
1/8"(3 mm) drill bits
Pencil
Wire stripper or utility knife
Tape measure or ruler
Pliers
Caulking gun and weatherproof caulking compound
Vent clamps
Jigsaw or keyhole saw
Flat-blade screwdriver
Metal snips
Phillips screwdriver
Parts needed
1/2"conduit
Two 1/2"(12.7 mm) UL listed or CSA approved strain reliefs
3 UL listed wire connectors
1 wall or roof cap
Metal vent system
Charcoal Filter Kit Part Number 4396848 for non-vented
(recirculating) installations only. See "Assistance or Service"
section to order.
Parts supplied
Remove parts from packages. Check that all parts are included.
Hood canopy assembly with ventilator and light bulbs
installed
Deflector for non-vented (recirculating) installations
Plastic transition with back draft dampers installed
Literature package
Filter(s) - depending on model and size
2 mounting hooks
Vent cover support bracket
Mounting template
2-piece vent cover
4-4x8mmscrews
10- 3.5 x 9.5 mm screws
4-5x35mmscrews
2 - 2.9 x 9.5 mm screws
2-6x70mm
IMPORTANT: Observe all governing codes and ordinances.
Have a qualified technician install the range hood. It is the
installer's responsibility to comply with installation clearances
specified on the model/serial rating plate. The model/serial rating
plate is located behind the left filter on the rear wall of the vent
hood.
Canopy hood location should be away from strong draft areas,
such as windows, doors and strong heating vents.
Cabinet opening dimensions that are shown must be used. Given
dimensions provide minimum clearance.
Grounded electrical outlet is required. See "Electrical
Requirements" section.
The canopy hood is factory set for venting through the roof or
wall. For non-vented (recirculating) Installation see "Non-vented
(recirculating) Installations" in "Prepare Location" section.
Charcoal Filter Kit Part Number 4393848 is available from your
dealer or an authorized parts distributor.
All openings in ceiling and wall where canopy hood will be
installed must be sealed.
For Mobile Home Installations
The installation of this range hood must conform to the
Manufactured Home Construction Safety Standards, Title 24
CFR, Part 328 (formerly the Federal Standard for Mobile Home
Construction and Safety, Title 24, HUD, Part 280) or when such
standard is not applicable, the standard for Manufactured Home
Installation 1982 (Manufactured Home Sites, Communities and
Setups) ANSI A225.1/NFPA 501A*, or latest edition, or with local
codes.
Product Dimensions
33 1/16"
(84.0 cm)
16%"
(42.3 cm',
.....i:
................................................................35 %" ...............................................................
(89.8 cm)
10 _3/_e"
(27.5 cm)
llllllllllll 21 1/4"
(%g.r.)
33 %e"
(84.0 cm)
aX.
3 1%6"
(10.0 cm)
2 3Is"
(6.0 cm)
J %"
(2.3era)
315/16"
(10.0 cm)
10 3/ld'
(27.5 era) 11%6"
_,--[ (28.7 cm)
3 15/16"
(10.0cm)
19 J''l/lo"
(5o.?ore)I
!i + TI
31%o"(10.0cm)
Installation Dimensions
,2s12"o , z'(5.1cm)min.
_-__..... L\ 7" (.17.8cm) min. (non-vented
__,.:. recMrcuJatinginst.ONLY)
10(2 4
Side
cabinet
..................................!............ 19 V_d'
(48.4cm)
I rnin.
30" (76.2 cm) rain. I
36" (91.4 cm) max. ',
bottom of canopy to Icenterline
cooking surface
Side
cabinet
Vent system must terminate to the outside, except for non-
vented (recirculating) installations.
Do not terminate the vent system in an attic or other enclosed
area.
Do not use 4" (10.2 cm) laundry-type wall caps.
Use metal vent only. Rigid metal vent is recommended. Do
not use plastic or metal foil vent.
The vent system must have a damper. If the roof or wall cap
has a damper, do not use the damper supplied with the range
hood.
For the most efficient and quiet operation:
Use a straight run or as few elbows as possible.
Use no more than three 90° elbows.
Make sure there is a minimum of 24" (61 cm) of straight vent
between the elbows if more than 1 elbow is used.
Do not install 2 elbows together.
Use clamps to seal all joints in the vent system.
Use caulking to seal exterior wall or roof opening around the
cap.
The size of the vent should be uniform.
Cold weather installations
An additional back draft damper should be installed to minimize
backward cold air flow and a nonmetallic thermal break should
be installed to minimize conduction of outside temperatures as
part of the vent system. The damper should be on the cold air
side of the thermal break.
The break should be as close as possible to where the vent
system enters the heated portion of the house.
Makeup air
Local building codes may require the use of make up air systems
when using ventilation systems greater than specified CFM of air
movement. The specified CFM varies from locale to locale.
Consult your HVAC professional for specific requirements in your
area.
Venting Methods
This canopy hood is factory set for venting through the roof or
wall.
A 6" (15.2 cm) round vent system is needed for installation (not
included). The hood exhaust opening is 6" (15.2 cm) round.
NOTE: Flexible vent is not recommended. Flexible vent creates
back pressure and air turbulence that greatly reduce
performance.
Vent system can terminate either through the roof or wall. To vent
through a wall, a 90° elbow is needed.
Rear discharge
A 90° elbow may beinstalled immediately above the hood.
For non-vented (recirculating) installations
If it is not possible to vent cooking fumes and vapors to the
outside, the hood can be used in the non-vented (recirculating)
version, fitting an activated carbon filter and the deflector. Fumes
and vapors are recycled through the top grille.
Roof Venting Wall Venting Non-vented
(recirculating)
B
A
-_!ii.......
A. Roof cap A. Wall cap A. Deflector
B. 6" (15.2 cm) B. 6" (15.2 cm) B. 6" (15.2 cm)
round vent round vent round vent
Calculating Vent System Length
To calculate the length of the system you need, add the
equivalent feet (meters) for each vent piece used in the system.
Vent Piece 6" (15.2 cm) Round
45° elbow 2.5 ft
(0.8m)
90° elbow 5.0 ft
(1.5m)
Maximum equivalent vent length is 35 ft (10.7 m).
Example vent system
90 ° elbow 1_6 ft (1.8 m)-_1 .....Wall cap
The following example falls within the maximum vent length of
35 ft (10.7 m).
1 - 90° elbow = 5.0 ft (1.5 m)
1 - wall cap = 0.0 ft (0.0 m)
8 ft (2.4 m) straight = 8.0 ft (2.4 m)
Length of system = 13.0 ft (3.9 m)
_ % _,_" _y",_ ,8
IMPORTANT: Observe all governing codes and ordinances. Save
Installation Instructions for electrical inspector's use.
It is the customer's responsibility to contact a qualified electrical
installer, and to ensure that the electrical installation is adequate
and in conformance with National Electrical Code, ANSl/NFPA 70
(latest edition), or CSA Standards C22.1-94, Canadian Electrical
Code, Part 1 and C22.2 No. 0-M91 (latest edition) and all local
codes and ordinances.
If codes permit and a separate ground wire is used, it is
recommended that a qualified electrician determine that the
ground path is adequate.
A copy of the above code standards can be obtained from:
National Fire Protection Association
One Batterymarch Park
Quincy, MA 02269
CSA International
8501 East Pleasant Valley Road
Cleveland, OH 44131-5575
A 120 Volt, 60 Hz., AC only 15-amp fused, electrical circuit is
required.
Do not ground to a gas pipe.
Check with a qualified electrician if you are not sure range
hood is properly grounded.
Do not have a fuse in the neutral or ground circuit.
The range hood must be connected with copper wire only.
The range hood should be connected directly to the fused
disconnect (or circuit breaker) box through flexible armored or
nonmetallic sheathed copper cable. It is recommended that a
separate circuit serving only this hood be provided.
Wire sizes (copper wire only) and connections must conform
with the rating of the appliance as specified on the model/
serial rating plate. The model/serial plate is located behind
the filter on the rear wall of the hood.
Wire sizes must conform to the requirements of the National
Electrical Code, ANSl/NFPA 70 (latest edition), or CSA
Standards C22.1-94, Canadian Electrical Code, Part 1 and
C22.2 No. 0-M91 (latest edition) and all local codes and
ordinances.
A V2"(12.7 mm) UL listed or CSA approved strain relief must
be provided at each end of the power supply cable (at the
range hood and at the junction box).
6
INSTALLATIONINSTRUCTIONS
m?scscc ton
It is recommended that the vent system be installed before 7. Tape template in place, aligning the template centerline and
hood is installed, bottom of template with hood bottom line and with the
centerline marked on the wall.
Do not cut a joist or stud unless absolutely necessary. If a
joist or stud must be cut, then a supporting frame must be i A
constructed. _== ....
Before making cutouts, make sure there is proper clearance
within the ceiling or wall for exhaust vent.
Check your ceiling height and the hood height maximum
before you select your hood.
Excessive Weight Hazard
Use two or more people to move and install range.
Failure to do so can result in back or other injury.
1. If possible, disconnect and move freestanding or slide-in
range from cabinet opening to provide easier access to rear
wall. Otherwise, put a thick, protective covering over
countertop, cooktop or range to protect from damage or dirt.
2. Determine which venting method to use: roof, wall, or non-
vented.
3. Select a flat surface for assembling the range hood. Cover
that surface with a protective covering.
Excessive Weight Hazard
Use two or more people to move and install
range hood.
Failure to do so can result in back or other injury.
4=
5.
6.
Using 2 or more people, lift range hood onto protective
covering.
Determine and mark the centerline on the wall where the
canopy hood will be installed.
Select a mounting height between a minimum of
30" (76.2 cm) and a suggested maximum of 36" (91.4 cm),
above the range to the bottom of the hood and mark
reference line on the wall.
NOTE: For installation locations with reduced ceilings
heights, the vent hood may be installed using the upper vent
cover for both vented and non-vented (recirculating)
installations.
8=
#
<
=
0 0 0 0
jJ
g s f
0 ..............................0
C
b,
3 =
D
A. Centerline
B. Mounting hook location
C. Fastener locations
D. Mounting height reference
Mark centers of the 6 fastener locations through the template
to the wall.
IMPORTANT: All screws must be installed into wood.
Remove the template.
9. Drill %4" (2.75 mm) pilot holes at all locations where screws
are being installed into wood.
10. Determine and make all necessary cuts in the wall for the vent
system. Install the vent system before installing the hood. See
"Venting Requirements" section.
11. Determine the required height for the 1/2"conduit and drill a
11¼"(3.2 cm) hole at this location.
12. Run wire through the 1/2"conduit according to the National
Electrical Code or CSA Standards and local codes and
ordinances. There must be enough 1/2"conduit and wires from
the fused disconnect (or circuit breaker) box to make the
connection in the hood's electrical terminal box.
13. Use caulk to seal all openings.
NOTE: Do not reconnect power until installation is complete.
14. Attach two mounting hooks to the wall at location marked on
the template.
A..... B
..........................i..............................
A. Mounting hooks
B. Centerline on wall
Vent Cover Bracket Installation
Installations using telescoping upper and lower vent cover
assembly
1. Position vent cover bracket on wall about 1/8"(3 mm) away
from the ceiling.
2. Mark the hole locations.
I A
i .........................
i ..........................C
A. Vent cover bracket
B. Mounting hole locations
C. Centerline on waft
3. Drill 3/8"(9.5 mm) holes for wall anchors and insert anchors
flush with the wall.
Vent Cover Bracket Assembly and Installation
4. Assemble the 3 pieces of the vent cover bracket using
four 4 x 8 mm screws provided. The assembled bracket
should be sized to fit inside the upper vent cover.
5,
A. Vent cover bracket assembly
B. Upper vent cover
C. 4 x 8 mm screws
D. Adjustable width
Install vent cover bracket to wall about 1/8"(3 mm) away from
the ceiling with drywall anchors and 6 x 70 mm screws
supplied.
I
i ...............A
i B
Non-vented (recirculating) Installation
1,
Assemble the 3 parts of the deflector with two 3.5 x 9.5 mm
screws provided. The assembled deflector should be sized to
fit the width of the vent cover bracket installed earlier.
C
2=
A. Vent cover bracket width
B. Deflector
C. 3.5 x 9.5 mm screws
Connect the deflector to the vent cover bracket using
four 3.5 x 9.5 mm screws provided.
B
I I
I I
A. Vent cover bracket
B. 3.5 x 9.5 mm screws
3. Measure length of 6" (15.2 cm) vent needed to connect the
transition to the deflector.
NOTE: Vent should fit up inside deflector a minimum of
1" (2.5 cm) minimum.
4. Install vent between the transition and the deflector.
5. Seal all connections with clamps.
A. Vent cover bracket
B. Centerline on wall
8
f"ss cl B c ageHooc
Excessive Weight Hazard
Use two or more people to move and install
range hood.
Failure to do so can result in back or other injury.
1=
Using 2 or more people, hang range hood on 2 mounting
hooks through the rectangular cutouts on back of hood.
ID
i
I
A ' E
M<:xE Connec on
Electrical Shock Hazard
Disconnect power before servicing.
Replace all parts and panels before operating.
Failure to do so can result in death or electrical shock.
1. Disconnect power.
2. Remove terminal box cover.
3. Remove the knockout in the terminal box cover and install the
UL-listed or CSA approved V2"strain relief.
4. Run 3 wires, black, white and green (14AWG) in W' conduit
from service panel to terminal box.
A
\
B
\
\
ii¸¸y
B
A. Mounting hooks
B. Mounting screws
C. Leveling screws
D. Centerline on wall
aS _
u
_C
s
E.Transition
F.3.5 x 9.5 mm screws
G.Terminalbox
2. Level the hood with leveling screws in mounting hooks or
rectangular cutouts, using a level across bottom of hood.
3. Secure hood with 4 screws through remaining 4 holes in
hood.
4. Install transition with 2 screws.
1=
_"_ ........... " .... _ w_'_sy_
C,o/stt@c!
Fit vent system over transition piece.
A .......
A. Vent system
B. Transition piece
2. Seal connection with clamps.
J !
D E F
A. UL-listed or CSA
approved strain relief
B. 1/_,,conduit
C. Terminal box
D. Black wires
E. Green (or bare) wire connected
to yellow-green wire
F. White wires
5. Use UL listed wire connectors and connect black wires
together.
6. Use UL listed wire connectors and connect white wires
together.
7=
Electrical Shock Hazard
Electrically ground blower.
Connect ground wire to green and yellow ground wire
in terminaJ box.
Failure to do so can result in death or electrical shock.
Connect ground wire to green and yellow ground wire in
terminal box using UL listed wire connectors.
8. Replaceterminalboxcover.
9. Checkalllightbulbstomakesuretheyaresecureintheir
sockets.
10.Reconnectpower.
1, Install vent cover.
Push lower cover down onto hood and lift upper cover to
ceiling and install with two 2.9 x 9.5 mm screws.
Connect the upper and lower vent covers with
two 3.5 x 9.5 mm screws apiece from the inside of the hood.
A. Upper vent cover
B. Lower vent cover
C. 2.9 x 9.5 mm screws
D. 3.5 x 9.5 mm screws
E.Bracket
1,
For non-vented (recirculating) installations, install charcoal
filter over grille on blower housing and turn filter handle
clockwise. Repeat with other charcoal filter.
..........................C
A. Blower housing
B. Filter handle
C. Charcoal filters
2. For all installations, insert back edge or metal filter into rear
channel of the filter opening.
3. Push handle toward the rear and push filter up.
4. Pull filter toward the front and insert into front channel.
{} 0 1 2 3
O Q
1. Press the light button ,6,. The light should turn on.
2. Press the "1" button. The blower should operate.
3. Press the "1" button for low speed, "2" button for medium
speed or "3" button for high speed.
4. Press the "0" button to turn off the blower.
5. If range hood does not operate, check to see whether a
circuit breaker has tripped or a household fuse has blown.
6. Disconnect power supply.
7. Check that the wiring is correct.
8. Replace all parts and panels before operating.
9. Reconnect power.
NOTE: To get the most efficient use from your new range hood,
read the "Range Hood Use" section.
RANGE HOOD USE
The canopy hood is designed to remove smoke, cooking vapors
and odors from the cooktop area. For best results, start the hood
before cooking and allow it to operate several minutes after the
cooking is complete to clear all smoke and odors from the
kitchen.
Hood control panel
The hood controls are located on the front side of the canopy.
r_ 0 1 2 3
';Q O%Q Q Q
Operating the light
1. Press the light button _. to turn on the light.
2. Press the light button £\ to turn off the light.
Operating the blower and adjusting blower speed
1. Press the "1" button for low speed, "2" button for medium
speed, "3" button for high speed.
2. Press the "0" button to turn off the blower.
10
RANGE HOOD CARE
IMPORTANT: Clean the hood and grease filters frequently To Replace Metal Grease Filters
according to the following instructions. Replace grease filters
before operating hood.
Be sure lights are cool before cleaning the hood.
Exterior surfaces
Clean the range hood with a mild detergent and soft cloth. Do not
use abrasive cleanser or steel-wool pads.
Metal grease filters
The filters should be washed frequently. Place metal filters in
dishwasher or hot detergent solution to clean.
Drain water through edge holes and let each filter dry thoroughly
before replacing it.
To Remove Metal Filters
1.
2.
3.
Turn off blower and lights. Check that halogen lamp is cool.
Push handle toward the rear and pull downward.
Pull filter toward the front.
To Replace Metal Grease Filter
1. Insert back edge of filter into rear channel of the filter
opening.
2. Push handle toward the rear and push filter up.
3. Pull filter toward the front and insert into front channel.
Charcoal Filters - for non-vented (recirculating) installations
The charcoal filters are not washable nor reusable.
They should be changed every 6 months in normal use.
The charcoal filters capture unpleasant cooking odors.
1. Insert back edge of filter into rear channel of the filter
opening.
2. Push handle toward the rear and push filter up.
3. Pull filter toward the front and insert into front channel.
To Replace Charcoal Filters
1. Turn blower and lights off. Check that halogen lamp is cool.
2. Remove the metal grease filters by pushing handle toward
the rear and pull downward.
3. Pull filter toward front and set aside.
4. Repeat to remove other filter.
5. Turn charcoal filter handle counterclockwise.
6. Remove and discard charcoal filter.
7. Repeat to remove other charcoal filter.
8. Install replacement charcoal filter over grille in blower housing
and turn filter handle clockwise.
9. Repeat to install other charcoal filter.
Replacing a Halogen Lamp
Turn off the range hood and allow the halogen lamp to cool.
Replace using a tissue.
If new lights do not operate, make sure the lamps are inserted
correctly before calling service.
1. Disconnect power.
2. Use a flat-blade screwdriver and gently pry the light cover
loose.
To Install Charcoal Filters
1. Turn blower and lights off. Check that halogen lamp is cool.
2. Remove the metal grease filters by pushing handle toward
the rear and pull downward.
3. Pull filter toward front and set aside.
4. Repeat to remove other metal filter.
5. Install charcoal filter over grille on blower housing and turn
filter handle clockwise.
...................C
3=
4.
\
Remove the lamp and replace with a 12-volt, 20-watt
maximum, halogen lamp made for a G-4 base.
Replace the light cover.
A. Blower housing
B. Filter handle
C. Charcoal filters
6. Repeat to install other charcoal filter.
11
WIRING DIAGRAM
SWx
1 02 0 1
3 4 %3 3-5
5 6 2-4 4-6
SW1 SW2 SW3 SW4 light motor
Light ON 1 x x x 0
Light OFF 0 x x x 0
Vel 1 x 1 0 0 1
Vel 2 x 0 1 0 1
Vel 3 x 0 0 1 1
Gi Bi Ne
BL L
6_ Oi5
BR
O
LA N M
Motor Connections Ohm resistance
speed to terminals between terminals
red-black 338
1 bridge:yellow-white
red-yellow 184
2 bridge:yellow-white
red-yellow 26t
3 bridge yellow-black
SA 406B/N
GY
GY
R
I
I _ 610 OI5
I 41 0 Oi 3
410 OI3 41@ OI3 410 OI3 I I
210 OI1 21® OI1 210 OI1 I j 21@ OI1
SW4 SW3 SW2 SWl
BK
W
Y
BU
BU
Y
W
BK
___I_
R
BR
R
GY
GY
GY
BR
Y-G
R
R
SE1LYA 1
® w
® ®
0 Y-G
12
ASSISTANCEOR SERVICE
When calling for assistance or service, please know the purchase
date and the complete model and serial number of your
appliance. This information will help us to better respond to your
request.
If you need replacement parts
If you need to order replacement parts, we recommend that you
use only factory specified parts. Factory specified parts will fit
right and work right because they are made with the same
precision used to build every new IKEA® appliance.
To locate factory specified parts in your area, call us or your
nearest designated service center.
n _he USA_
Call the Whirlpool Customer eXperience Center
toll-free: 1-866-664-2449.
Our consultants provide assistance with:
Features and specifications on our full line of appliances.
Installation information.
Use and maintenance procedures.
Accessory and repair parts sales.
Specialized customer assistance (Spanish speaking, hearing
impaired, limited vision, etc.).
Referrals to local dealers, repair parts distributors and service
companies. Whirlpool designated service technicians are
trained to fulfill the product warranty and provide after-
warranty service, anywhere in the United States.
To locate the Whirlpool designated service company in your
area, you can also look in your telephone directory Yellow
Pages.
Accessories List
Charcoal Filter Kit
Part Number 4396848
Call the Whirlpool Canada LP Customer Interaction Centre toll
free: 1-866-664-2449.
Our consultants provide assistance with:
Features and specifications on our full line of appliances.
Use and maintenance procedures.
Accessory and repair parts sales.
Referrals to local dealers, repair parts distributors, and
service companies. Whirlpool Canada LP designated service
technicians are trained to fulfill the product warranty and
provide after-warranty service, anywhere in Canada.
For further assistance
If you need further assistance, you can write to Whirlpool
Canada LP with any questions or concerns at:
Customer Interaction Centre
Whirlpool Canada LP
1901 Minnesota Court
Mississauga, Ontario L5N 3A7
Please include a daytime phone number in your correspondence.
Accessories List
Charcoal Filter Kit
Part Number 4396848
For further assistance
If you need further assistance, you can write to Whirlpool
Corporation with any questions or concerns at:
IKEA Brand Home Appliances
Customer eXperience Center
553 Benson Road
Benton Harbor, MI 49022-2692
Please include a daytime phone number in your correspondence.
IKEAMAJOR APPLIANCEWARRANTY
How long is the IKEA limited warranty valid?
This limited warranty is valid for five years from the date of purchase, when this major appliance is operated and maintained according
to instructions attached to or furnished with the product, unless the appliance is named LAGAN in which case this limited warranty is
valid for one year from the date of purchase. This limited warranty is valid only in the United States or Canada and applies only when the
major appliance is used in the country in which it was purchased. Proof of original purchase date is required to obtain service under this
limited warranty.
Which appliances are not covered by the IKEA five (5) year limited warranty?
For major appliances named "LAGAN", this limited warranty is valid for one year from the date of purchase.
Who will execute the service?
This limited warranty is provided by Whirlpool Corporation or Whirlpool Canada LP (hereafter "Whirlpool"). Service must be provided by
a Whirlpool designated service company.
13
What does this limited warranty cover?
The limited warranty will pay for factory specified parts and repair labor to correct defects in materials or workmanship that existed
when the major appliance was purchased. The exceptions are specified under the headline "What is not covered under this limited
warranty?".
What will be done to correct the problem?
The designated service company will examine the product and decide, at its sole discretion, if it is covered under this limited warranty.
If considered covered, the designated service company will then repair the defect. Your sole and exclusive remedy under this limited
warranty shall be product repair as provided herein.
What is not covered under this limited warranty?
Service calls to correct the installation of your major appliance, to instruct you on how to use your major appliance, to replace or
repair house fuses, or to correct house wiring or plumbing.
Service calls to repair or replace appliance light bulbs, air filters or water filters. Consumable parts are excluded from warranty
coverage.
Replacement parts or repair labor if this major appliance is used for other than normal, single-family household use or when it is used
in a manner that is inconsistent to published user or operator instructions and/or installation instructions.
Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in
accordance with electrical or plumbing codes, or use of consumables or cleaning products not approved for use.
Cosmetic damage, including scratches, dents, chips or other damage to the finish of your major appliance, unless such damage
results from defects in materials or workmanship and is reported within 30 days from the date of purchase.
Any food loss or medicine loss due to refrigerator or freezer product failures.
Pick up and delivery. This major appliance is intended to be repaired in your home.
Repairs to parts or systems resulting from unauthorized modifications made to the appliance.
Expenses for travel and transportation for product service if your major appliance is located in a remote area where service by an
authorized servicer is not available.
The removal and reinstallation of your major appliance if it is installed in an inaccessible location or is not installed in accordance with
published installation instructions.
Replacement parts or repair labor on major appliances with original model/serial numbers that have been removed, altered or cannot
be easily determined.
The cost of repair or replacement under these excluded circumstances shall be borne by the customer.
Disclaimer of Implied Warranties
IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR
A PARTICULAR PURPOSE, ARE LIMITED TO FIVE YEARS (ONE YEAR FOR MAJOR APPLIANCES NAMED "LAGAN") OR THE
SHORTEST PERIOD ALLOWED BY LAW. Some states and provinces do not allow limitations on the duration of implied warranties of
merchantability or fitness, so this limitation may not apply to you. This warranty gives you specific legal rights, and you also may have
other rights that vary from state to state or province to province.
Limitation of Remedies; Exclusion of Incidental and Consequential Damages
YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN.
WHIRLPOOL SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow
the exclusion or limitation of incidental or consequential damages, so these limitations and exclusions may not apply to you. This
warranty gives you specific legal rights, and you also may have other rights that vary from state to state or province to province.
How to reach us if you need our service
If outside the 50 United States and Canada, contact your authorized IKEA retailer to determine if another warranty applies.
If you need service, please read the Installation Instructions and/or the "Troubleshooting" section of the Use & Care Guide before
contacting us. Ifyou need additional help, do not hesitate to contact us in the U.S.A. and Canada at 1-866-664-2449.
2/09
Keep this book and your sales slip together for future
reference. You must provide proof of purchase or installation
date for in-warranty service.
Write down the following information about your major appliance
to better help you obtain assistance or service if you ever need it.
You will need to know your complete model number and serial
number. You can find this information on the model and serial
number label located on the product.
Dealer name
Address
Phone number
Model number
Serial number
Purchase date
14
SECURITEDELA HOTTEDECUlSlNIERE
Votre securite et celle des autres est tres importante.
Nous donnons de nombreux messages de s_curit_ importants dans ce manuel et sur votre appareil m_nager. Assurez-vous de
toujours lire tousles messages de s_curit_ et de vous y conformer.
Voici le symbole d'alerte de s_curit&
Ce symbole d'alerte de s_curit_ vous signale les dangers potentiels de d_c_s et de blessures graves &vous
et & d'autres.
Tousles messages de s_curit_ suivront le symbole d'alerte de s_curit_ et le mot "DANGER" ou
"AVERTISSEMENT". Ces mots signifient
Risque possible de d_cbs ou de blessure grave si vous ne
suivez pas imm_diatement les instructions.
Risque possible de d_cbs ou de blessure grave si vous
ne suivez pas les instructions.
Tous les messages de s_curit_ vous diront quel est le danger potentiel et vous disent comment r_duire le risque de blessure et
ce qui peut se produire en cas de non-respect des instructions.
15
IMPORTANTES iNSTRUCTiONS DE SECURITE
AVERTISSEMENT : POUR Rt_DUIRE LE RISQUE
D'INCENDIE, CHOC ¢:LECTRIQUE OU DOMMAGES
CORPORELS, RESPECTER LES INSTRUCTIONS
SUIVANTES :
m Utiliser cet appareil uniquement dans les applications
envisag6es par le fabricant. Pour toute question, contacter
le fabricant.
m Avant d'entreprendre un travail d'entretien ou de nettoyage,
interrompre I'alimentation de la hotte au niveau du tableau
de disjoncteurs, et verrouiller le tableau de disjoncteurs
pour emp6cher tout r@ablissement accidentel de
I'alimentation du circuit. Lorsqu'il n'est pas possible de
verrouiller le tableau de disjoncteurs, placer sur le tableau
de disjoncteurs une 6tiquette d'avertissement pro6minente
interdisant le r@ablissement de I'alimentation.
m Tout travail d'installation ou c&blage 61ectrique doit @re
r6alis6 par une personne qualifi6e, dans le respect des
prescriptions de tousles codes et normes applicables, y
compris les codes du b_timent et de protection contre les
incendies.
m Une source d'air de d6bit suffisant est n6cessaire pour le
fonctionnement correct de tout appareil & gaz (combustion
et 6vacuation des gaz &combustion par la chemin6e), pour
qu'il n'y ait pas de reflux des gaz de combustion. Respecter
les directives du fabricant de 1'6quipement de chauffage et
les prescriptions des normes de s6curit6 - comme celles
publi6es par la National Fire Protection Association (NFPA)
et I'American Society for Heating, Refrigeration and Air
Conditioning Engineers (ASHRAE), et les prescriptions des
autorit6s r6glementaires locales.
m Lors d'op@ations de d6coupage et de per£age dans un mur
ou un plafond, veiller a ne pas endommager les c&blages
61ectriques ou canalisations qui peuvent s'y trouver.
m Les syst_mes d'6vacuation doivent toujours d6charger I'air
I'ext@ieur.
MISE EN GARDE : Cet appareil est con(2u uniquement
pour la ventilation g6n@ale. Ne pas I'utiliser pour I'extraction
de mati@es ou vapeurs dangereuses ou explosives.
MISE EN GARDE : Pour minimiser le risque d'incendie
et 6vacuer ad6quatement les gaz, veiller &acheminer I'air
aspir6 par un conduit jusqu'& I'ext@ieur - ne pas d6charger
I'air aspir6 dans un espace vide du b_timent comme une
cavit6 murale, un plafond, un grenier, un vide sanitaire ou
un garage.
AVERTISSEMENT : POUR RC:DUIRE LE RISQUE
D'INCENDIE, UTILISER UNIQUEMENT DES CONDUITS
METALLIQUES.
AVERTISSEMENT : POUR MINIMISER LE RISQUE
D'UN FEU DE GRAISSE SUR LA CUISINIF:RE :
[] Ne jamais laisser un 616ment de surface fonctionner &
puissance de chauffage maximale sans surveillance. Un
renversement/d6bordement de mati@e graisseuse pourrait
provoquer une inflammation et la g6n@ation de fum6e.
Utiliser une puissance de chauffage moyenne ou basse
pour le chauffage d'huile.
[] Veiller &toujours faire fonctionner le ventilateur de la hotte
Iors de la cuisson avec une puissance de chauffage 61ev6e
ou Iors de la cuisson d'un mets & flamber (& savoir cr6pes
Suzette, cerise jubil6e, steak au poivre flamb6).
[] Nettoyer fr6quemment les ventilateurs d'extraction. Veiller &
ne pas laisser la graisse s'accumuler sur les surfaces du
ventilateur ou des filtres.
[] Utiliser toujours un ustensile de taille appropri6e. Utiliser
toujours un ustensile adapt6 & la taille de 1'616ment
chauffant.
AVERTISSEMENT : POUR REDUIRE LE RISQUE DE
DOMMAGES CORPORELS APRES LE Dt_CLENCHEMENT
D'UN FEU DE GRAISSE SUR LA CUISINI_:RE, APPLIQUER
LES RECOMMANDATIONS SUIVANTES :a
[] Placer sur le r6cipient un couvercle bien ajust6, une t61e &
biscuits ou un plateau m6tallique POUR ETOUFFER LES
FLAMMES, p.uis @eindre le brt_leur &gaz ou 61ectrique.
VEILLER A EVITER LES BRULURES. Si les flammes ne
s'6teignent pas imm6diatement, EVACUER LA PIt_CE ET
APPELER LES POMPIERS.
[] NE JAMAIS PRENDRE EN MAIN UN RECIPIENT
ENFLAMME - vous risquez de vous brQler.
[] NE PAS UTILISER D'EAU, ni un torchon humide - ceci
pourrait provoquer une explosion de vapeur brQlante.
[] Utiliser un extincteur SEULEMENT si:
- IIs'agit d'un extincteur de classe ABC, dont on connaft le
fonctionnement.
- IIs'agit d'un petit feu encore limit6 & I'endroit oQ il s'est
d6clar&
- Les pompiers ont 6te contactes.
- II est possible de garder le dos orient6 vers une sortie
pendant I'op@ation de lutte contre le feu.
aRecommandations tir6es des conseils de s6curit6 en cas
d'incendie de cuisine publi6s par la NFPA.
[] AVERTISSEMENT : Pour r6duire le risque d'incendie
ou de choc 61ectrique, ne pas utiliser ce ventilateur avec un
quelconque dispositif de r6glage de la vitesse & semi-
conducteurs.
CONSERVEZ CES INSTRUCTIONS
16
EXIGENCESD'INSTALLATION
Rassembler les outils et pieces necessaires avant de commencer
I'installation. Lire et suivre les instructions fournies avec les outils
indiqu6s ici.
Outillage n_cessaire
Niveau
Perceuse avec forets de 11¼"(3 cm), 3/8"(9,5 mm),
7A4"(2,75 mm) et 1/8"(3 mm)
Crayon
Pince & denuder ou couteau utilitaire
Metre-ruban ou regle
Pince
Pistolet & calfeutrage et compose de calfeutrage resistant
aux intemperies
Brides pour conduit d'evacuation
Scie sauteuse ou scie & guichet
Tournevis & lame plate
Cisaille de ferblantier
Tournevis Phillips
Pi_ces n_cessaires
Conduit de dia. 1/2"
Deux serre-c&ble de V2"(12,7 mm) - homologation UL
ou CSA
3 connecteurs de ills homologues UL
1 bouche de decharge (decharge a travers lemur ou & travers
le toit)
Conduit d'evacuation metallique
Ensemble de filtre a charbon (piece n° 4396848) - seulement
pour une installation sans decharge a I'exterieur (recyclage).
Voir la section "Assistance ou service" pour placer une
commande.
Filtre(s) - selon le modele et la dimension
2 crochets de montage
Bride de support du cache-conduit
Gabarit de montage
Cache-conduit- 2 pieces
4visde4x8mm
10 vis de 3,5 x 9,5 mm
4visde5x35mm
2 vis de 2,9 x 9,5 mm
2visde6x70mm
_xs;cs#s_s#_®<CJ@/"Y'SDCSC@m@SS_'
IMPORTANT : Observer les dispositions de tousles codes et
reglements en vigueur.
Confier I'installation de la hotte &un technicien qualifi& C'est
I'installateur qu'incombe la responsabilite de respecter les
distances de separation exigees, specifiees sur la plaque
signaletique de I'appareil. La plaque signaletique de I'appareil est
situee derriere le filtre de gauche, sur la paroi arriere de la hotte.
On dolt toujours installer la hotte a distance des sources de
courant d'air (fen@tres, portes et bouches de chauffage).
Respecter les dimensions indiquees pour les ouvertures
decouper dans les placards; ces dimensions tiennent compte
des valeurs mJnJmales des degagements de separation.
On doit disposer d'une prise de courant electrique reliee a la
terre. Voir la section "Specifications electriques'.
La hotte est configuree a I'usine pour la decharge a travers le toit
ou un mur. Pour une installation sans decharge a I'exterieur
(recyclage), voir "Installation sans decharge & I'exterieur
(recyclage)" & la section "Raccordement du circuit d'evacuation'.
L'ensemble Filtre a charbon (piece numero 4396848) est
disponible chez votre marchand ou chez un distributeur de
pieces autorise.
On doit assurer I'etancheite au niveau de chaque ouverture
decoupee dans le plafond ou un mur traverse par I'equJpement
de la hotte.
Pi_ces fournies
Retirer les pieces des emballages. Verifier que toutes les pieces
sont presentes.
Hotte avec ventilateur et lampes installes
Deflecteur pour installation sans decharge a I'exterieur
(recyclage)
Raccord de transition en plastique avec clapet anti-reflux
installe
Sachet de documents
Installation dans une r_sidence mobile
L'installation de cette hotte doit satisfaire aux exigences de la
norme Manufactured Home Construction Safety Standards, Titre
24 CFR, partie 328 (anciennement Federal Standard for Mobile
Home Construction and Safety, Titre 24, HUD, partie 280);
Iorsque cette norme n'est pas applicable, I'installation doit
satisfaire aux criteres de la plus recente edition de la norme
Manufactured Home Installation 1982 (Manufactured Home
Sites, Communities and Setups) ANSI A225.1/NFPA 501A*, ou
des codes et reglements Iocaux.
17
Dimensions du produit Dimensions a respecter Iors de rinstallation
11%0"
10 13/16"
(27,5 crn)
llllllilllll
IIIIIIIIIIII
33 Vlo"
(84 cm)
_21211/4"
(54,0 cm)
rain.
33 IAo"
(84,0 cm)
max.
2 3/8"
(6 cm)
10" 2" (5,1 cm) rain.
(254cm) 7" (17,8 cm) min.
\ _ (installations sans d_charge
.... _ rext_rieur SEULEMENT)
Placard
lateral
30" (76,2 cm) rnin.
36" (91,4 crn) max.
entre la base de
la hotte et la surface
de cuisson
35 _&"
(90 crn) rnin.
Axe central
Placard
lateral
21 W'
(54cm)
I'RIn.
33 V_d'
16%" (84 crn)
(42,3cm) m_
rnln.
33 _/_6"
(84,0 cm)
max.
16%"
(42,3 crn)
3 15/16H
(10sin)
Le syst@me d'@vacuation doit d@charger I'air a I'ext@rieur,
except@ pour les installations sans d@charge a I'ext@rieur.
Ne pas terminer le conduit d'@vacuation dans un grenier ou
dans un autre espace ferm&
Ne pas utiliser une bouahe de d@aharge murale de
4" (10,2 am) normalement utilis@e pour un @quipement
de buanderie.
Utiliser un conduit m_tallique uniquement. Un conduit en
m_tal rigide est recommand& Ne pas utiliser de conduit de
plastique ou de m_tal tr_s mince.
Le systeme d'evacuation doit comporter un clapet. Si la
bouche de decharge murale ou par le toit comporte un
clapet, ne pas utiliser le clapet fourni avec la hotte de
cuisiniere.
Pour un fonctionnement efficace et silencieux :
Utiliser autant que possible des sections droites et minimiser
le nombre de coudes.
Ne pas utiliser plus de trois coudes & 90°.
Veiller & ce qu'il y ait une section droite de conduit de
24" (61 cm) ou plus entre deux coudes, si on doit utiliser plus
de un raccord coud&
Ne pas installer 2 coudes ensemble.
Au niveau de chaque jointure du conduit de decharge,
assurer I'etancheite avec des brides.
Autour de la bouche de decharge a I'exterieur, assurer
I'etancheite avec un produit de calfeutrage.
La taille du conduit doit 6tre uniforme.
18
Installations pour r_gions & climat froid
On doit installer un clapet anti-reflux additionnel pour minimiser
le reflux d'air froid. Un el6ment non m6tallique d'isolation
thermique doit _tre installe pour minimiser la conduction des
temperatures exterieures par I'interm6diaire du conduit
d'evacuation. Le clapet anti-reflux doit _tre place du c6te air froid
par rapport & I'el6ment d'isolation thermique.
L'el6ment d'isolation thermique doit _tre aussi proche que
possible de I'endroit oQ le systeme d'evacuation s'introduit dans
la partie chauffee de la maison.
Renouvellement de I'air
Le code du bAtiment local peut exiger I'emploi d'un systeme
d'appoint d'air Iors de I'emploi d'un ventilateur d'extraction dont
la capacite d'aspiration est superieure &un debit (pieds cubes
par minute) specifi& Le debit specifi6, pieds cubes par minute,
est variable d'une juridiction & une autre. Consulter un
professionnel des installations de chauffage ventilation/
climatisation au sujet des exigences specifiques applicables
dans la juridiction locale.
M6thodes d'_vacuation
Cette hotte est configuree & I'usine pour la decharge de I'air
aspire a travers le toit ou & travers un mur.
Un circuit d'evacuation en conduit rond de 6" (15,2 cm) est
necessaire pour I'installation (non fourni). La hotte comporte une
ouverture de sortie de diam_tre 6" (15,2 cm).
REMARQUE • On deconseille I'emploi d'un conduit flexible. Un
conduit flexible peut causer une retro-pression et des
turbulences de I'air, ce qui reduit considerablement la
performance.
La sortie a I'exterieur du circuit d'evacuation peut se faire &
travers le toit ou &travers un mur. Pour la sortie atravers un mur,
on doit employer un raccord coude & 90°.
D6charge par I'arri_re
Le raccord coude & 90 ° peut _tre installe imm6diatement au-
dessus de la hotte.
Installation sans d_charge & I'ext_rieur (recyclage)
S'il n'est pas possible d'evacuer les fumees et vapeurs de
cuisson & I'exterieur, on peut employer la version "installation
sans decharge & I'exterieur (recyclage)" de la hotte dotee d'un
filtre & charbon actif et du deflecteur. Les vapeurs/fum6es sont
alors recyclees a travers la grille superieure.
D_charge a D_charge
travers le toit travers le mur
A
L
Installation sans
d_charge a I'ext_rieur
(recyclage)
A. Bouche de A. Bouche de A. D_flecteur
d_charge sur toit d_charge murale B. Conduit dia.
B. Conduit dia. B. Conduit dia. 6" (15,2 cm)
6" (15,2 cm) 6" (15,2 cm)
Calcul de la Iongueur effective du circuit d'_vacuation
Pour calculer la Iongueur effective du circuit d'evacuation
necessaire, additionner les Iongueurs equivalentes (pieds/m_tres)
de tousles composants utilises dans le systeme.
Composant Conduit de diam_tre
6" (15,2 cm)
coude & 45° 2,5 pi
(0,8m)
coude & 90° 5 pi
(1,5m)
La Iongueurequivalente maximum est de 35 pi (10,7cm).
Exemple de syst_me de d_charge
Bouche de
Coude _ 90° I___ 6pi(1,8rn)-_ decharge murale
Dans I'exemple suivant, la Iongueur theorique du circuit est
inferieure au maximum de 35 pi (10,7 m).
1 -coudea90 ° =5pi(1,5m)
1 - bouche de = 0 pi (0 m)
decharge murale
section droite de = 8 pi (2,4 m)
8 pi (2,4 m)
Longueur du systeme = 13 pi (3,9 m)
19
IMPORTANT : Observer les dispositions de tousles codes et
reglements en vigueur. Conserver les instructions d'installation
pour consultation par I'inspecteur des installations electriques.
C'est au client qu'incombe la responsabilite de contacter un
electricien qualifie et de veiller &ce que I'installation electrique
soit adequate et realisee en conformite avec les prescriptions de
la plus recente edition de la norme National Electrical Code,
ANSI/NFPA 70, ou de la norme CSA C22.1-94, Code canadien de
I'electricite, partie 1 et C22.2 0-M91, et de tous les codes et
reglements Iocaux en vigueur.
Si les codes le permettent et si on utilise un conducteur distinct
de liaison &la terre, il est recommande qu'un electricien qualifie
verifie la qualite de la liaison & la terre.
Pour obtenir un exemplaire de la norme des codes ci-dessus,
contacter :
National Fire Protection Association
One Batterymarch Park
Quincy, MA 02269
CSA International
8501 East Pleasant Valley Road
Cleveland, OH 44131-5575
L'appareil dolt etre alimente par un circuit de 120 V,60 Hz,
CA seulement, 15 amperes, protege par fusible.
Ne pas utiliser une tuyauterie de gaz pour le raccordement &
la terre.
En cas de doute quanta la qualite de la liaison & la terre de la
hotte de la cuisiniere, consulter un electricien qualifi&
Ne pas installer un fusible dans le conducteur neutre ou le
conducteur de liaison & la terre.
La hotte dolt etre raccordee au reseau electrique uniquement
avec des conducteurs de cuivre.
La hotte dolt etre raccordee directement au coupe-circuit
avec fusible ou au disjoncteur par I'intermediaire de c&ble &
conducteurs de cuivre, & blindage metallique flexible ou &
gaine non-metallique. IIest recommande de raccorder la
hotte sur un circuit distinct exclusif & cet appareil.
Le calibre des conducteurs (cuivre seulement) et les
connexions doivent etre compatibles avec la demande de
courant de I'appareil specifiee sur la plaque signaletique. La
plaque signaletique de I'appareil est situee derriere le filtre,
sur la paroi arriere de la hotte.
Le calibre des conducteurs dolt satisfaire les exigences de la
plus recente edition de la norme National Electrical Code,
ANSI/NFPA 70, ou de la norme CSA C22.1-94, Code
canadien de I'electricite, partie 1 et C22.2 0-M91 et de
tousles codes et reglements en vigueur.
Un serre-c&ble de 1/2"(12,7 mm) (homologation UL ou CSA)
dolt etre installe a chaque extremite du c&ble d'alimentation
(sur la hotte et sur le boitier de distribution).
INSTRUCTIONSD'INSTALLATION
R) 6 w}sdo de
On recommande que le circuit d'evacuation soit installe avant
I'installation de la hotte.
On ne dolt couper un poteau de colombage ou une solive
que si c'est absolument necessaire. Dans ce cas, on devra
construire une structure de support appropriee.
Avant d'executer les decoupages, verifier la disponibilite d'un
espace de passage suffisant dans le plafond ou lemur pour
le conduit d'evacuation.
Avant de selectionner la hotte & installer, mesurer la hauteur
libre sous plafond et la hauteur maximum disponible sous la
hotte.
3. Selectionner une surface plane pour I'assemblage de la
hotte. Recouvrir cette surface d'un materiau de protection.
Risque du poids excessif
Utiiiser deux ou plus de personnes pour d_piacer et
installer la hotte de la cuisini_re.
Le non=respect de cette instruction peut causer
une blessure au dos ou d'autre blessure.
Risque du poids excessif
Utiiiser deux ou plus de personnes pour d_piacer et
installer la cuisini_re.
Le non=respect de cette instruction peut causer
une blessure au dos ou d'autre blessure.
1. Si possible, deconnecter la cuisiniere autonome ou
encastree, et deplacer celle-ci hors de I'espace d'installation
entre les placards, pour faciliter I'acces au mur arriere. Sinon,
placer une epaisse couverture de protection sur le plan de
travail, la cuisiniere ou latable de cuisson pour la protection
contre les dommages ou souillures.
2. Determiner la methode d'extraction &utiliser : decharge &
travers lemur ou le toit, ou recyclage.
4. A I'aide de deux personnes ou plus, soulever la hotte de la
cuisiniere et la poser sur une surface de protection.
5. Determiner et marquer la position de I'axe central sur le mur
oQ la hotte sera installee.
6. Choisir une hauteur de montage - minimum 30" (76,2 cm) et
maximum suggere 36" (91,4 cm) - au-dessus de la cuisiniere
jusqu'au fond de la hotte et tracer une ligne de reference sur
lemur.
REMARQUE : Pour une configuration d'installation avec
hauteur sous plafond reduite (installation avec ou sans
decharge & I'exterieur), la hotte peut etre installee avec la
section superieure du cache-conduit.
7. Fixer le gabarit en place avec du ruban adhesif; aligner I'axe
central du gabarit et le bas du gabarit avec la ligne
correspondant au bas de la hotte, et avec I'axe central dej&
trace sur le mur.
20
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28

IKEA IH5303SS0 Guide d'installation

Catégorie
Hottes
Taper
Guide d'installation
Ce manuel convient également à

dans d''autres langues