IKEA IH5303SS0 Guide d'installation

Marque: IKEA

Modèle: IH5303SS0

Catégorie: Hottes

Taper: Guide d'installation

Ce manuel convient également à

IH5303WS0

|KEA ®

90 CM (35 2/5")WALL-MOUNT

CANOPY RANGE HOOD

HOTTEDE CUlSlNII:RE POUR

MONTAGE MURAL 90 CM (35 2/5")

Table of Contents/Table des matieres ............................................................................. 2

IMPORTANT: READ AND SAVE THESE INSTRUCTIONS.

FOR RESIDENTIAL USE ONLY.

IMPORTANT : LIRE ET CONSERVER CES INSTRUCTIONS.

POUR UTILISATION RESIDENTIELLE UNIQUEMENT.

IMPORTANT:

Installer: Leave installation instructions with the homeowner.

Homeowner: Keep installation instructions for future reference.

Save installation instructions for local electrical inspector's use.

IMPORTANT :

Installateur : Remettre les instructions d'installation au propri_taire.

Propri6taire : Conserver les instructions d'installation pour r_f@ence ult@ieure.

Conserver les instructions d'installation pour consultation par I'inspecteur local des installations _lectriques.

W10018030A

TABLEOF CONTENTS

RANGE HOOD SAFETY ................................................................. 2

INSTALLATION REQUIREMENTS ................................................ 4

Tools and Parts ............................................................................ 4

Location Requirements ................................................................ 4

Venting Requirements .................................................................. 5

Electrical Requirements ............................................................... 6

INSTALLATION INSTRUCTIONS .................................................. 7

Prepare Location .......................................................................... 7

Install Range Hood ....................................................................... 9

Connect Vent System (for vented installations only) ................... 9

Make Electrical Connection ......................................................... 9

Complete Installation ................................................................. 10

Install Filters ................................................................................ 10

Check Operation ........................................................................ 10

RANGE HOOD USE ...................................................................... 10

Operation .................................................................................... 10

RANGE HOOD CARE ................................................................... 11

Cleaning and Maintenance ........................................................ 11

WIRING DIAGRAM ...................................................................... 12

ASSISTANCE OR SERVICE ......................................................... 13

In the U.S.A................................................................................ 13

In Canada ................................................................................... 13

WAR RANTY .................................................................................. 13

TABLEDESMATIERES

SECURITE DE LA HOTTE DE CUlSINIERE ............................... 15

EXIGENCES D'INSTALLATION ................................................... 17

Outillage et pieces ...................................................................... 17

Exigences d'emplacement ......................................................... 17

Exigences concernant I'evacuation ........................................... 18

Specifications electriques .......................................................... 20

INSTRUCTIONS D'INSTALLATION ............................................. 20

Preparation de I'emplacement ................................................... 20

Installation de la hotte ................................................................ 22

Installation du conduit d'evacuation

(pour installations avec decharge &I'exterieur uniquement) .....22

Raccordement electrique ........................................................... 23

Achever I'installation .................................................................. 23

Installation des filtres .................................................................. 24

Contr61e du fonctionnement ...................................................... 24

UTILISATION DE LA HOTTE DE CUlSINIF:RE ........................... 24

Fonctionnement ......................................................................... 24

ENTRETIEN DE LA HOTTE DE CUlSINIF:RE ............................. 24

Nettoyage et entretien ................................................................ 24

SCHEMA DE C,&,BLAGE .............................................................. 26

ASSISTANCE OU SERVICE ......................................................... 27

GARANTIE ..................................................................................... 27

RANGE HOOD SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

iMPORTANT SAFETY iNSTRUCTiONS

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK, OR INJURY TO PERSONS, OBSERVE THE

FOLLOWING:

[] Use this unit only in the manner intended by the

manufacturer. If you have questions, contact the

manufacturer.

[] Before servicing or cleaning the unit, switch the power off at

the service panel disconnecting means to prevent power

from being switched on accidentally. When the service

disconnecting means cannot be locked, securely fasten a

prominent warning device, such as a tag, to the service

panel.

[] Installation work and electrical wiring must be done by

qualified person(s) in accordance with all applicable codes

& standards, including fire-rated construction.

[] Sufficient air is needed for proper combustion and

exhausting of gases through the flue (chimney) of fuel

burning equipment to prevent backdrafting. Follow the

heating equipment manufacturer's guideline and safety

standards such as those published by the National Fire

Protection Association (NFPA), the American Society for

Heating, Refrigeration and Air Conditioning Engineers

(ASHRAE), and the local code authorities.

[] When cutting or drilling into wall or ceiling; do not damage

electrical wiring and other utilities.

[] Ducted systems must always be vented outdoors.

CAUTION: For general ventilating use only. Do not use

to exhaust hazardous or explosive materials and vapors.

CAUTION: To reduce risk of fire and to properly exhaust

air, be sure to duct air outside - do not vent exhaust air into

spaces within walls ceilings, attics, crawl spaces, or

garages.

WARNING: TO REDUCE THE RISK OF FIRE, USE ONLY

METAL DUCTWORK.

WARNING: TO REDUCE THE RISK OF A RANGE TOP

GREASE FIRE:

[] Never leave the surface units unattended at high settings.

Boilovers cause smoking and greasy spillovers that may

ignite. Heat oils slowly on low or medium settings.

[] Always turn hood ON when cooking at high heat or when

flambeing food (i.e. Crepes Suzette, Cherries Jubilee,

Peppercorn Beef Flamb_).

[] Clean ventilating fans frequently. Grease should not be

allowed to accumulate on fan or filter.

[] Use proper pan size. Always use cookware appropriate for

the size of the surface element.

WARNING: TO REDUCE THE RISK OF INJURY TO

PERSONS IN THE EVENT OF A RANGE TOP GREASE

FIRE, OBSERVE THE FOLLOWING: a

[] SMOTHER FLAMES with a close fitting lid, cookie sheet, or

other metal tray, then turn off the gas burner or electric

element. BE CAREFUL TO PREVENT BURNS. If the

flames do not go out immediately, EVACUATE AND CALL

THE FIRE DEPARTMENT.

[] NEVER PICK UP A FLAMING PAN - you may be burned.

[] DO NOT USE WATER, including wet dishcloths or towels -

a violent steam explosion will result.

[] Use an extinguisher ONLY if:

- You know you have a class ABC extinguisher, and you

already know how to operate it.

- The fire is small and contained in the area where it

started.

- The fire department is being called.

- You can fight the fire with your back to an exit.

aBased on "Kitchen Fire Safety Tips" published by NFPA.

[] WARNING: To reduce the risk of fire or electrical shock,

do not use this fan with any solid-state speed control

device.

SAVE THESE INSTRUCTIONS

INSTALLATIONREQUIREMENTS

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

Tools needed

• Level

• Drill with 11¼'' (3 cm), 3/8"(9.5 mm), 7/64"(2.75 mm) and

1/8"(3 mm) drill bits

• Pencil

• Wire stripper or utility knife

• Tape measure or ruler

• Pliers

• Caulking gun and weatherproof caulking compound

• Vent clamps

• Jigsaw or keyhole saw

• Flat-blade screwdriver

• Metal snips

• Phillips screwdriver

Parts needed

• 1/2"conduit

• Two 1/2"(12.7 mm) UL listed or CSA approved strain reliefs

• 3 UL listed wire connectors

• 1 wall or roof cap

• Metal vent system

• Charcoal Filter Kit Part Number 4396848 for non-vented

(recirculating) installations only. See "Assistance or Service"

section to order.

Parts supplied

Remove parts from packages. Check that all parts are included.

• Hood canopy assembly with ventilator and light bulbs

installed

• Deflector for non-vented (recirculating) installations

• Plastic transition with back draft dampers installed

• Literature package

• Filter(s) - depending on model and size

• 2 mounting hooks

• Vent cover support bracket

• Mounting template

• 2-piece vent cover

• 4-4x8mmscrews

• 10- 3.5 x 9.5 mm screws

• 4-5x35mmscrews

• 2 - 2.9 x 9.5 mm screws

• 2-6x70mm

IMPORTANT: Observe all governing codes and ordinances.

Have a qualified technician install the range hood. It is the

installer's responsibility to comply with installation clearances

specified on the model/serial rating plate. The model/serial rating

plate is located behind the left filter on the rear wall of the vent

hood.

Canopy hood location should be away from strong draft areas,

such as windows, doors and strong heating vents.

Cabinet opening dimensions that are shown must be used. Given

dimensions provide minimum clearance.

Grounded electrical outlet is required. See "Electrical

Requirements" section.

The canopy hood is factory set for venting through the roof or

wall. For non-vented (recirculating) Installation see "Non-vented

(recirculating) Installations" in "Prepare Location" section.

Charcoal Filter Kit Part Number 4393848 is available from your

dealer or an authorized parts distributor.

All openings in ceiling and wall where canopy hood will be

installed must be sealed.

For Mobile Home Installations

The installation of this range hood must conform to the

Manufactured Home Construction Safety Standards, Title 24

CFR, Part 328 (formerly the Federal Standard for Mobile Home

Construction and Safety, Title 24, HUD, Part 280) or when such

standard is not applicable, the standard for Manufactured Home

Installation 1982 (Manufactured Home Sites, Communities and

Setups) ANSI A225.1/NFPA 501A*, or latest edition, or with local

codes.

Product Dimensions

33 1/16"

(84.0 cm)

16%"

(42.3 cm',

.....i:

................................................................35 %" ...............................................................

(89.8 cm)

10 _3/_e"

(27.5 cm)

llllllllllll 21 1/4"

(%g.r.)

33 %e"

(84.0 cm)

aX.

3 1%6"

(10.0 cm)

2 3Is"

(6.0 cm)

J %"

(2.3era)

315/16"

(10.0 cm)

10 3/ld'

(27.5 era) 11%6"

_,--[ (28.7 cm)

3 15/16"

(10.0cm)

19 J''l/lo"

(5o.?ore)I

!i + TI

31%o"(10.0cm)

Installation Dimensions

,2s12"o , z'(5.1cm)min.

_-__..... L\ 7" (.17.8cm) min. (non-vented

__,.:. recMrcuJatinginst.ONLY)

10(2 4

Side

cabinet

..................................!............ 19 V_d'

(48.4cm)

I rnin.

30" (76.2 cm) rain. I

36" (91.4 cm) max. ',

bottom of canopy to Icenterline

cooking surface

Side

cabinet

• Vent system must terminate to the outside, except for non-

vented (recirculating) installations.

• Do not terminate the vent system in an attic or other enclosed

area.

• Do not use 4" (10.2 cm) laundry-type wall caps.

• Use metal vent only. Rigid metal vent is recommended. Do

not use plastic or metal foil vent.

• The vent system must have a damper. If the roof or wall cap

has a damper, do not use the damper supplied with the range

hood.

For the most efficient and quiet operation:

• Use a straight run or as few elbows as possible.

• Use no more than three 90° elbows.

• Make sure there is a minimum of 24" (61 cm) of straight vent

between the elbows if more than 1 elbow is used.

• Do not install 2 elbows together.

• Use clamps to seal all joints in the vent system.

• Use caulking to seal exterior wall or roof opening around the

cap.

• The size of the vent should be uniform.

Cold weather installations

An additional back draft damper should be installed to minimize

backward cold air flow and a nonmetallic thermal break should

be installed to minimize conduction of outside temperatures as

part of the vent system. The damper should be on the cold air

side of the thermal break.

The break should be as close as possible to where the vent

system enters the heated portion of the house.

Makeup air

Local building codes may require the use of make up air systems

when using ventilation systems greater than specified CFM of air

movement. The specified CFM varies from locale to locale.

Consult your HVAC professional for specific requirements in your

area.

Venting Methods

This canopy hood is factory set for venting through the roof or

wall.

A 6" (15.2 cm) round vent system is needed for installation (not

included). The hood exhaust opening is 6" (15.2 cm) round.

NOTE: Flexible vent is not recommended. Flexible vent creates

back pressure and air turbulence that greatly reduce

performance.

Vent system can terminate either through the roof or wall. To vent

through a wall, a 90° elbow is needed.

Rear discharge

A 90° elbow may beinstalled immediately above the hood.

For non-vented (recirculating) installations

If it is not possible to vent cooking fumes and vapors to the

outside, the hood can be used in the non-vented (recirculating)

version, fitting an activated carbon filter and the deflector. Fumes

and vapors are recycled through the top grille.

Roof Venting Wall Venting Non-vented

(recirculating)

-_!ii.......

A. Roof cap A. Wall cap A. Deflector

B. 6" (15.2 cm) B. 6" (15.2 cm) B. 6" (15.2 cm)

round vent round vent round vent

Calculating Vent System Length

To calculate the length of the system you need, add the

equivalent feet (meters) for each vent piece used in the system.

Vent Piece 6" (15.2 cm) Round

45° elbow 2.5 ft

(0.8m)

90° elbow 5.0 ft

(1.5m)

Maximum equivalent vent length is 35 ft (10.7 m).

Example vent system

90 ° elbow 1_6 ft (1.8 m)-_1 .....Wall cap

The following example falls within the maximum vent length of

35 ft (10.7 m).

1 - 90° elbow = 5.0 ft (1.5 m)

1 - wall cap = 0.0 ft (0.0 m)

8 ft (2.4 m) straight = 8.0 ft (2.4 m)

Length of system = 13.0 ft (3.9 m)

_ % _,_" _y",_ ,8 •

IMPORTANT: Observe all governing codes and ordinances. Save

Installation Instructions for electrical inspector's use.

It is the customer's responsibility to contact a qualified electrical

installer, and to ensure that the electrical installation is adequate

and in conformance with National Electrical Code, ANSl/NFPA 70

(latest edition), or CSA Standards C22.1-94, Canadian Electrical

Code, Part 1 and C22.2 No. 0-M91 (latest edition) and all local

codes and ordinances.

If codes permit and a separate ground wire is used, it is

recommended that a qualified electrician determine that the

ground path is adequate.

A copy of the above code standards can be obtained from:

National Fire Protection Association

One Batterymarch Park

Quincy, MA 02269

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

• A 120 Volt, 60 Hz., AC only 15-amp fused, electrical circuit is

required.

• Do not ground to a gas pipe.

• Check with a qualified electrician if you are not sure range

hood is properly grounded.

• Do not have a fuse in the neutral or ground circuit.

• The range hood must be connected with copper wire only.

• The range hood should be connected directly to the fused

disconnect (or circuit breaker) box through flexible armored or

nonmetallic sheathed copper cable. It is recommended that a

separate circuit serving only this hood be provided.

• Wire sizes (copper wire only) and connections must conform

with the rating of the appliance as specified on the model/

serial rating plate. The model/serial plate is located behind

the filter on the rear wall of the hood.

Wire sizes must conform to the requirements of the National

Electrical Code, ANSl/NFPA 70 (latest edition), or CSA

Standards C22.1-94, Canadian Electrical Code, Part 1 and

C22.2 No. 0-M91 (latest edition) and all local codes and

ordinances.

• A V2"(12.7 mm) UL listed or CSA approved strain relief must

be provided at each end of the power supply cable (at the

range hood and at the junction box).

INSTALLATIONINSTRUCTIONS

m?scscc ton

It is recommended that the vent system be installed before 7. Tape template in place, aligning the template centerline and

hood is installed, bottom of template with hood bottom line and with the

centerline marked on the wall.

Do not cut a joist or stud unless absolutely necessary. If a

joist or stud must be cut, then a supporting frame must be i A

constructed. _== ....

• Before making cutouts, make sure there is proper clearance

within the ceiling or wall for exhaust vent.

• Check your ceiling height and the hood height maximum

before you select your hood.

Excessive Weight Hazard

Use two or more people to move and install range.

Failure to do so can result in back or other injury.

1. If possible, disconnect and move freestanding or slide-in

range from cabinet opening to provide easier access to rear

wall. Otherwise, put a thick, protective covering over

countertop, cooktop or range to protect from damage or dirt.

2. Determine which venting method to use: roof, wall, or non-

vented.

3. Select a flat surface for assembling the range hood. Cover

that surface with a protective covering.

Excessive Weight Hazard

Use two or more people to move and install

range hood.

Failure to do so can result in back or other injury.

Using 2 or more people, lift range hood onto protective

covering.

Determine and mark the centerline on the wall where the

canopy hood will be installed.

Select a mounting height between a minimum of

30" (76.2 cm) and a suggested maximum of 36" (91.4 cm),

above the range to the bottom of the hood and mark

reference line on the wall.

NOTE: For installation locations with reduced ceilings

heights, the vent hood may be installed using the upper vent

cover for both vented and non-vented (recirculating)

installations.

0 0 0 0

g s f

0 ..............................0

3 =

A. Centerline

B. Mounting hook location

C. Fastener locations

D. Mounting height reference

Mark centers of the 6 fastener locations through the template

to the wall.

IMPORTANT: All screws must be installed into wood.

Remove the template.

9. Drill %4" (2.75 mm) pilot holes at all locations where screws

are being installed into wood.

10. Determine and make all necessary cuts in the wall for the vent

system. Install the vent system before installing the hood. See

"Venting Requirements" section.

11. Determine the required height for the 1/2"conduit and drill a

11¼"(3.2 cm) hole at this location.

12. Run wire through the 1/2"conduit according to the National

Electrical Code or CSA Standards and local codes and

ordinances. There must be enough 1/2"conduit and wires from

the fused disconnect (or circuit breaker) box to make the

connection in the hood's electrical terminal box.

13. Use caulk to seal all openings.

NOTE: Do not reconnect power until installation is complete.

14. Attach two mounting hooks to the wall at location marked on

the template.

A..... B

..........................i..............................

A. Mounting hooks

B. Centerline on wall

Vent Cover Bracket Installation

Installations using telescoping upper and lower vent cover

assembly

1. Position vent cover bracket on wall about 1/8"(3 mm) away

from the ceiling.

2. Mark the hole locations.

I A

i .........................

i ..........................C

A. Vent cover bracket

B. Mounting hole locations

C. Centerline on waft

3. Drill 3/8"(9.5 mm) holes for wall anchors and insert anchors

flush with the wall.

Vent Cover Bracket Assembly and Installation

4. Assemble the 3 pieces of the vent cover bracket using

four 4 x 8 mm screws provided. The assembled bracket

should be sized to fit inside the upper vent cover.

A. Vent cover bracket assembly

B. Upper vent cover

C. 4 x 8 mm screws

D. Adjustable width

Install vent cover bracket to wall about 1/8"(3 mm) away from

the ceiling with drywall anchors and 6 x 70 mm screws

supplied.

i ...............A

i B

Non-vented (recirculating) Installation

Assemble the 3 parts of the deflector with two 3.5 x 9.5 mm

screws provided. The assembled deflector should be sized to

fit the width of the vent cover bracket installed earlier.

A. Vent cover bracket width

B. Deflector

C. 3.5 x 9.5 mm screws

Connect the deflector to the vent cover bracket using

four 3.5 x 9.5 mm screws provided.

I I

A. Vent cover bracket

B. 3.5 x 9.5 mm screws

3. Measure length of 6" (15.2 cm) vent needed to connect the

transition to the deflector.

NOTE: Vent should fit up inside deflector a minimum of

1" (2.5 cm) minimum.

4. Install vent between the transition and the deflector.

5. Seal all connections with clamps.

A. Vent cover bracket

B. Centerline on wall

f"ss cl B c ageHooc

Excessive Weight Hazard

Use two or more people to move and install

range hood.

Failure to do so can result in back or other injury.

Using 2 or more people, hang range hood on 2 mounting

hooks through the rectangular cutouts on back of hood.

A ' E

M<:x<®E Connec on

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

1. Disconnect power.

2. Remove terminal box cover.

3. Remove the knockout in the terminal box cover and install the

UL-listed or CSA approved V2"strain relief.

4. Run 3 wires, black, white and green (14AWG) in W' conduit

from service panel to terminal box.

ii¸¸y

A. Mounting hooks

B. Mounting screws

C. Leveling screws

D. Centerline on wall

aS _

E.Transition

F.3.5 x 9.5 mm screws

G.Terminalbox

2. Level the hood with leveling screws in mounting hooks or

rectangular cutouts, using a level across bottom of hood.

3. Secure hood with 4 screws through remaining 4 holes in

hood.

4. Install transition with 2 screws.

_"_ ........... " .... _ w_'_sy_

C,o/stt@c!

Fit vent system over transition piece.

A .......

A. Vent system

B. Transition piece

2. Seal connection with clamps.

J !

D E F

A. UL-listed or CSA

approved strain relief

B. 1/_,,conduit

C. Terminal box

D. Black wires

E. Green (or bare) wire connected

to yellow-green wire

F. White wires

5. Use UL listed wire connectors and connect black wires

together.

6. Use UL listed wire connectors and connect white wires

together.

Electrical Shock Hazard

Electrically ground blower.

Connect ground wire to green and yellow ground wire

in terminaJ box.

Failure to do so can result in death or electrical shock.

Connect ground wire to green and yellow ground wire in

terminal box using UL listed wire connectors.

8. Replaceterminalboxcover.

9. Checkalllightbulbstomakesuretheyaresecureintheir

sockets.

10.Reconnectpower.

1, Install vent cover.

Push lower cover down onto hood and lift upper cover to

ceiling and install with two 2.9 x 9.5 mm screws.

Connect the upper and lower vent covers with

two 3.5 x 9.5 mm screws apiece from the inside of the hood.

A. Upper vent cover

B. Lower vent cover

C. 2.9 x 9.5 mm screws

D. 3.5 x 9.5 mm screws

E.Bracket

For non-vented (recirculating) installations, install charcoal

filter over grille on blower housing and turn filter handle

clockwise. Repeat with other charcoal filter.

..........................C

A. Blower housing

B. Filter handle

C. Charcoal filters

2. For all installations, insert back edge or metal filter into rear

channel of the filter opening.

3. Push handle toward the rear and push filter up.

4. Pull filter toward the front and insert into front channel.

{} 0 1 2 3

O Q

1. Press the light button ,6,. The light should turn on.

2. Press the "1" button. The blower should operate.

3. Press the "1" button for low speed, "2" button for medium

speed or "3" button for high speed.

4. Press the "0" button to turn off the blower.

5. If range hood does not operate, check to see whether a

circuit breaker has tripped or a household fuse has blown.

6. Disconnect power supply.

7. Check that the wiring is correct.

8. Replace all parts and panels before operating.

9. Reconnect power.

NOTE: To get the most efficient use from your new range hood,

read the "Range Hood Use" section.

RANGE HOOD USE

The canopy hood is designed to remove smoke, cooking vapors

and odors from the cooktop area. For best results, start the hood

before cooking and allow it to operate several minutes after the

cooking is complete to clear all smoke and odors from the

kitchen.

Hood control panel

The hood controls are located on the front side of the canopy.

r_ 0 1 2 3

';Q O%Q Q Q

Operating the light

1. Press the light button _. to turn on the light.

2. Press the light button £\ to turn off the light.

Operating the blower and adjusting blower speed

1. Press the "1" button for low speed, "2" button for medium

speed, "3" button for high speed.

2. Press the "0" button to turn off the blower.

RANGE HOOD CARE

IMPORTANT: Clean the hood and grease filters frequently To Replace Metal Grease Filters

according to the following instructions. Replace grease filters

before operating hood.

Be sure lights are cool before cleaning the hood.

Exterior surfaces

Clean the range hood with a mild detergent and soft cloth. Do not

use abrasive cleanser or steel-wool pads.

Metal grease filters

The filters should be washed frequently. Place metal filters in

dishwasher or hot detergent solution to clean.

Drain water through edge holes and let each filter dry thoroughly

before replacing it.

To Remove Metal Filters

Turn off blower and lights. Check that halogen lamp is cool.

Push handle toward the rear and pull downward.

Pull filter toward the front.

To Replace Metal Grease Filter

1. Insert back edge of filter into rear channel of the filter

opening.

2. Push handle toward the rear and push filter up.

3. Pull filter toward the front and insert into front channel.

Charcoal Filters - for non-vented (recirculating) installations

The charcoal filters are not washable nor reusable.

They should be changed every 6 months in normal use.

The charcoal filters capture unpleasant cooking odors.

1. Insert back edge of filter into rear channel of the filter

opening.

2. Push handle toward the rear and push filter up.

3. Pull filter toward the front and insert into front channel.

To Replace Charcoal Filters

1. Turn blower and lights off. Check that halogen lamp is cool.

2. Remove the metal grease filters by pushing handle toward

the rear and pull downward.

3. Pull filter toward front and set aside.

4. Repeat to remove other filter.

5. Turn charcoal filter handle counterclockwise.

6. Remove and discard charcoal filter.

7. Repeat to remove other charcoal filter.

8. Install replacement charcoal filter over grille in blower housing

and turn filter handle clockwise.

9. Repeat to install other charcoal filter.

Replacing a Halogen Lamp

Turn off the range hood and allow the halogen lamp to cool.

Replace using a tissue.

If new lights do not operate, make sure the lamps are inserted

correctly before calling service.

1. Disconnect power.

2. Use a flat-blade screwdriver and gently pry the light cover

loose.

To Install Charcoal Filters

1. Turn blower and lights off. Check that halogen lamp is cool.

2. Remove the metal grease filters by pushing handle toward

the rear and pull downward.

3. Pull filter toward front and set aside.

4. Repeat to remove other metal filter.

5. Install charcoal filter over grille on blower housing and turn

filter handle clockwise.

...................C

Remove the lamp and replace with a 12-volt, 20-watt

maximum, halogen lamp made for a G-4 base.

Replace the light cover.

A. Blower housing

B. Filter handle

C. Charcoal filters

6. Repeat to install other charcoal filter.

WIRING DIAGRAM

SWx

1 • 02 0 1

3 • • 4 %3 3-5

5 6 2-4 4-6

SW1 SW2 SW3 SW4 light motor

Light ON 1 x x x 0

Light OFF 0 x x x 0

Vel 1 x 1 0 0 1

Vel 2 x 0 1 0 1

Vel 3 x 0 0 1 1

Gi Bi Ne

BL L

6_ Oi5

LA N M

Motor Connections Ohm resistance

speed to terminals between terminals

red-black 338

1 bridge:yellow-white

red-yellow 184

2 bridge:yellow-white

red-yellow 26t

3 bridge yellow-black

SA 406B/N

• I

I _ 610 OI5

I 41 0 Oi 3

410 OI3 41@ OI3 410 OI3 I I

210 OI1 21® OI1 210 OI1 I j 21@ OI1

SW4 SW3 SW2 SWl

___I_

Y-G

SE1LYA 1

® w

® ®

0 Y-G

ASSISTANCEOR SERVICE

When calling for assistance or service, please know the purchase

date and the complete model and serial number of your

appliance. This information will help us to better respond to your

request.

If you need replacement parts

If you need to order replacement parts, we recommend that you

use only factory specified parts. Factory specified parts will fit

right and work right because they are made with the same

precision used to build every new IKEA® appliance.

To locate factory specified parts in your area, call us or your

nearest designated service center.

n _he USA_

Call the Whirlpool Customer eXperience Center

toll-free: 1-866-664-2449.

Our consultants provide assistance with:

• Features and specifications on our full line of appliances.

• Installation information.

• Use and maintenance procedures.

• Accessory and repair parts sales.

• Specialized customer assistance (Spanish speaking, hearing

impaired, limited vision, etc.).

• Referrals to local dealers, repair parts distributors and service

companies. Whirlpool designated service technicians are

trained to fulfill the product warranty and provide after-

warranty service, anywhere in the United States.

To locate the Whirlpool designated service company in your

area, you can also look in your telephone directory Yellow

Pages.

Accessories List

Charcoal Filter Kit

Part Number 4396848

Call the Whirlpool Canada LP Customer Interaction Centre toll

free: 1-866-664-2449.

Our consultants provide assistance with:

• Features and specifications on our full line of appliances.

• Use and maintenance procedures.

• Accessory and repair parts sales.

• Referrals to local dealers, repair parts distributors, and

service companies. Whirlpool Canada LP designated service

technicians are trained to fulfill the product warranty and

provide after-warranty service, anywhere in Canada.

For further assistance

If you need further assistance, you can write to Whirlpool

Canada LP with any questions or concerns at:

Customer Interaction Centre

Whirlpool Canada LP

1901 Minnesota Court

Mississauga, Ontario L5N 3A7

Please include a daytime phone number in your correspondence.

Accessories List

Charcoal Filter Kit

Part Number 4396848

For further assistance

If you need further assistance, you can write to Whirlpool

Corporation with any questions or concerns at:

IKEA Brand Home Appliances

Customer eXperience Center

553 Benson Road

Benton Harbor, MI 49022-2692

Please include a daytime phone number in your correspondence.

IKEAMAJOR APPLIANCEWARRANTY

How long is the IKEA limited warranty valid?

This limited warranty is valid for five years from the date of purchase, when this major appliance is operated and maintained according

to instructions attached to or furnished with the product, unless the appliance is named LAGAN in which case this limited warranty is

valid for one year from the date of purchase. This limited warranty is valid only in the United States or Canada and applies only when the

major appliance is used in the country in which it was purchased. Proof of original purchase date is required to obtain service under this

limited warranty.

Which appliances are not covered by the IKEA five (5) year limited warranty?

For major appliances named "LAGAN", this limited warranty is valid for one year from the date of purchase.

Who will execute the service?

This limited warranty is provided by Whirlpool Corporation or Whirlpool Canada LP (hereafter "Whirlpool"). Service must be provided by

a Whirlpool designated service company.

What does this limited warranty cover?

The limited warranty will pay for factory specified parts and repair labor to correct defects in materials or workmanship that existed

when the major appliance was purchased. The exceptions are specified under the headline "What is not covered under this limited

warranty?".

What will be done to correct the problem?

The designated service company will examine the product and decide, at its sole discretion, if it is covered under this limited warranty.

If considered covered, the designated service company will then repair the defect. Your sole and exclusive remedy under this limited

warranty shall be product repair as provided herein.

What is not covered under this limited warranty?

• Service calls to correct the installation of your major appliance, to instruct you on how to use your major appliance, to replace or

repair house fuses, or to correct house wiring or plumbing.

• Service calls to repair or replace appliance light bulbs, air filters or water filters. Consumable parts are excluded from warranty

coverage.

• Replacement parts or repair labor if this major appliance is used for other than normal, single-family household use or when it is used

in a manner that is inconsistent to published user or operator instructions and/or installation instructions.

• Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in

accordance with electrical or plumbing codes, or use of consumables or cleaning products not approved for use.

• Cosmetic damage, including scratches, dents, chips or other damage to the finish of your major appliance, unless such damage

results from defects in materials or workmanship and is reported within 30 days from the date of purchase.

• Any food loss or medicine loss due to refrigerator or freezer product failures.

• Pick up and delivery. This major appliance is intended to be repaired in your home.

• Repairs to parts or systems resulting from unauthorized modifications made to the appliance.

• Expenses for travel and transportation for product service if your major appliance is located in a remote area where service by an

authorized servicer is not available.

• The removal and reinstallation of your major appliance if it is installed in an inaccessible location or is not installed in accordance with

published installation instructions.

• Replacement parts or repair labor on major appliances with original model/serial numbers that have been removed, altered or cannot

be easily determined.

The cost of repair or replacement under these excluded circumstances shall be borne by the customer.

Disclaimer of Implied Warranties

IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR

A PARTICULAR PURPOSE, ARE LIMITED TO FIVE YEARS (ONE YEAR FOR MAJOR APPLIANCES NAMED "LAGAN") OR THE

SHORTEST PERIOD ALLOWED BY LAW. Some states and provinces do not allow limitations on the duration of implied warranties of

merchantability or fitness, so this limitation may not apply to you. This warranty gives you specific legal rights, and you also may have

other rights that vary from state to state or province to province.

Limitation of Remedies; Exclusion of Incidental and Consequential Damages

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN.

WHIRLPOOL SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow

the exclusion or limitation of incidental or consequential damages, so these limitations and exclusions may not apply to you. This

warranty gives you specific legal rights, and you also may have other rights that vary from state to state or province to province.

How to reach us if you need our service

If outside the 50 United States and Canada, contact your authorized IKEA retailer to determine if another warranty applies.

If you need service, please read the Installation Instructions and/or the "Troubleshooting" section of the Use & Care Guide before

contacting us. Ifyou need additional help, do not hesitate to contact us in the U.S.A. and Canada at 1-866-664-2449.

2/09

Keep this book and your sales slip together for future

reference. You must provide proof of purchase or installation

date for in-warranty service.

Write down the following information about your major appliance

to better help you obtain assistance or service if you ever need it.

You will need to know your complete model number and serial

number. You can find this information on the model and serial

number label located on the product.

Dealer name

Address

Phone number

Model number

Serial number

Purchase date

SECURITEDELA HOTTEDECUlSlNIERE

Votre securite et celle des autres est tres importante.

Nous donnons de nombreux messages de s_curit_ importants dans ce manuel et sur votre appareil m_nager. Assurez-vous de

toujours lire tousles messages de s_curit_ et de vous y conformer.

Voici le symbole d'alerte de s_curit&

Ce symbole d'alerte de s_curit_ vous signale les dangers potentiels de d_c_s et de blessures graves &vous

et & d'autres.

Tousles messages de s_curit_ suivront le symbole d'alerte de s_curit_ et le mot "DANGER" ou

"AVERTISSEMENT". Ces mots signifient •

Risque possible de d_cbs ou de blessure grave si vous ne

suivez pas imm_diatement les instructions.

Risque possible de d_cbs ou de blessure grave si vous

ne suivez pas les instructions.

Tous les messages de s_curit_ vous diront quel est le danger potentiel et vous disent comment r_duire le risque de blessure et

ce qui peut se produire en cas de non-respect des instructions.

IMPORTANTES iNSTRUCTiONS DE SECURITE

AVERTISSEMENT : POUR Rt_DUIRE LE RISQUE

D'INCENDIE, CHOC ¢:LECTRIQUE OU DOMMAGES

CORPORELS, RESPECTER LES INSTRUCTIONS

SUIVANTES :

m Utiliser cet appareil uniquement dans les applications

envisag6es par le fabricant. Pour toute question, contacter

le fabricant.

m Avant d'entreprendre un travail d'entretien ou de nettoyage,

interrompre I'alimentation de la hotte au niveau du tableau

de disjoncteurs, et verrouiller le tableau de disjoncteurs

pour emp6cher tout r@ablissement accidentel de

I'alimentation du circuit. Lorsqu'il n'est pas possible de

verrouiller le tableau de disjoncteurs, placer sur le tableau

de disjoncteurs une 6tiquette d'avertissement pro6minente

interdisant le r@ablissement de I'alimentation.

m Tout travail d'installation ou c&blage 61ectrique doit @re

r6alis6 par une personne qualifi6e, dans le respect des

prescriptions de tousles codes et normes applicables, y

compris les codes du b_timent et de protection contre les

incendies.

m Une source d'air de d6bit suffisant est n6cessaire pour le

fonctionnement correct de tout appareil & gaz (combustion

et 6vacuation des gaz &combustion par la chemin6e), pour

qu'il n'y ait pas de reflux des gaz de combustion. Respecter

les directives du fabricant de 1'6quipement de chauffage et

les prescriptions des normes de s6curit6 - comme celles

publi6es par la National Fire Protection Association (NFPA)

et I'American Society for Heating, Refrigeration and Air

Conditioning Engineers (ASHRAE), et les prescriptions des

autorit6s r6glementaires locales.

m Lors d'op@ations de d6coupage et de per£age dans un mur

ou un plafond, veiller a ne pas endommager les c&blages

61ectriques ou canalisations qui peuvent s'y trouver.

m Les syst_mes d'6vacuation doivent toujours d6charger I'air

I'ext@ieur.

MISE EN GARDE : Cet appareil est con(2u uniquement

pour la ventilation g6n@ale. Ne pas I'utiliser pour I'extraction

de mati@es ou vapeurs dangereuses ou explosives.

MISE EN GARDE : Pour minimiser le risque d'incendie

et 6vacuer ad6quatement les gaz, veiller &acheminer I'air

aspir6 par un conduit jusqu'& I'ext@ieur - ne pas d6charger

I'air aspir6 dans un espace vide du b_timent comme une

cavit6 murale, un plafond, un grenier, un vide sanitaire ou

un garage.

AVERTISSEMENT : POUR RC:DUIRE LE RISQUE

D'INCENDIE, UTILISER UNIQUEMENT DES CONDUITS

METALLIQUES.

AVERTISSEMENT : POUR MINIMISER LE RISQUE

D'UN FEU DE GRAISSE SUR LA CUISINIF:RE :

[] Ne jamais laisser un 616ment de surface fonctionner &

puissance de chauffage maximale sans surveillance. Un

renversement/d6bordement de mati@e graisseuse pourrait

provoquer une inflammation et la g6n@ation de fum6e.

Utiliser une puissance de chauffage moyenne ou basse

pour le chauffage d'huile.

[] Veiller &toujours faire fonctionner le ventilateur de la hotte

Iors de la cuisson avec une puissance de chauffage 61ev6e

ou Iors de la cuisson d'un mets & flamber (& savoir cr6pes

Suzette, cerise jubil6e, steak au poivre flamb6).

[] Nettoyer fr6quemment les ventilateurs d'extraction. Veiller &

ne pas laisser la graisse s'accumuler sur les surfaces du

ventilateur ou des filtres.

[] Utiliser toujours un ustensile de taille appropri6e. Utiliser

toujours un ustensile adapt6 & la taille de 1'616ment

chauffant.

AVERTISSEMENT : POUR REDUIRE LE RISQUE DE

DOMMAGES CORPORELS APRES LE Dt_CLENCHEMENT

D'UN FEU DE GRAISSE SUR LA CUISINI_:RE, APPLIQUER

LES RECOMMANDATIONS SUIVANTES :a

[] Placer sur le r6cipient un couvercle bien ajust6, une t61e &

biscuits ou un plateau m6tallique POUR ETOUFFER LES

FLAMMES, p.uis @eindre le brt_leur &gaz ou 61ectrique.

VEILLER A EVITER LES BRULURES. Si les flammes ne

s'6teignent pas imm6diatement, EVACUER LA PIt_CE ET

APPELER LES POMPIERS.

[] NE JAMAIS PRENDRE EN MAIN UN RECIPIENT

ENFLAMME - vous risquez de vous brQler.

[] NE PAS UTILISER D'EAU, ni un torchon humide - ceci

pourrait provoquer une explosion de vapeur brQlante.

[] Utiliser un extincteur SEULEMENT si:

- IIs'agit d'un extincteur de classe ABC, dont on connaft le

fonctionnement.

- IIs'agit d'un petit feu encore limit6 & I'endroit oQ il s'est

d6clar&

- Les pompiers ont 6te contactes.

- II est possible de garder le dos orient6 vers une sortie

pendant I'op@ation de lutte contre le feu.

aRecommandations tir6es des conseils de s6curit6 en cas

d'incendie de cuisine publi6s par la NFPA.

[] AVERTISSEMENT : Pour r6duire le risque d'incendie

ou de choc 61ectrique, ne pas utiliser ce ventilateur avec un

quelconque dispositif de r6glage de la vitesse & semi-

conducteurs.

CONSERVEZ CES INSTRUCTIONS

EXIGENCESD'INSTALLATION

Rassembler les outils et pieces necessaires avant de commencer

I'installation. Lire et suivre les instructions fournies avec les outils

indiqu6s ici.

Outillage n_cessaire

• Niveau

• Perceuse avec forets de 11¼"(3 cm), 3/8"(9,5 mm),

7A4"(2,75 mm) et 1/8"(3 mm)

• Crayon

• Pince & denuder ou couteau utilitaire

• Metre-ruban ou regle

• Pince

• Pistolet & calfeutrage et compose de calfeutrage resistant

aux intemperies

• Brides pour conduit d'evacuation

• Scie sauteuse ou scie & guichet

• Tournevis & lame plate

• Cisaille de ferblantier

• Tournevis Phillips

Pi_ces n_cessaires

• Conduit de dia. 1/2"

Deux serre-c&ble de V2"(12,7 mm) - homologation UL

ou CSA

• 3 connecteurs de ills homologues UL

• 1 bouche de decharge (decharge a travers lemur ou & travers

le toit)

• Conduit d'evacuation metallique

• Ensemble de filtre a charbon (piece n° 4396848) - seulement

pour une installation sans decharge a I'exterieur (recyclage).

Voir la section "Assistance ou service" pour placer une

commande.

• Filtre(s) - selon le modele et la dimension

• 2 crochets de montage

• Bride de support du cache-conduit

• Gabarit de montage

• Cache-conduit- 2 pieces

• 4visde4x8mm

• 10 vis de 3,5 x 9,5 mm

• 4visde5x35mm

• 2 vis de 2,9 x 9,5 mm

• 2visde6x70mm

_xs;cs#s_s#_®<CJ@/"Y'SDCSC@m@SS_'

IMPORTANT : Observer les dispositions de tousles codes et

reglements en vigueur.

Confier I'installation de la hotte &un technicien qualifi& C'est

I'installateur qu'incombe la responsabilite de respecter les

distances de separation exigees, specifiees sur la plaque

signaletique de I'appareil. La plaque signaletique de I'appareil est

situee derriere le filtre de gauche, sur la paroi arriere de la hotte.

On dolt toujours installer la hotte a distance des sources de

courant d'air (fen@tres, portes et bouches de chauffage).

Respecter les dimensions indiquees pour les ouvertures

decouper dans les placards; ces dimensions tiennent compte

des valeurs mJnJmales des degagements de separation.

On doit disposer d'une prise de courant electrique reliee a la

terre. Voir la section "Specifications electriques'.

La hotte est configuree a I'usine pour la decharge a travers le toit

ou un mur. Pour une installation sans decharge a I'exterieur

(recyclage), voir "Installation sans decharge & I'exterieur

(recyclage)" & la section "Raccordement du circuit d'evacuation'.

L'ensemble Filtre a charbon (piece numero 4396848) est

disponible chez votre marchand ou chez un distributeur de

pieces autorise.

On doit assurer I'etancheite au niveau de chaque ouverture

decoupee dans le plafond ou un mur traverse par I'equJpement

de la hotte.

Pi_ces fournies

Retirer les pieces des emballages. Verifier que toutes les pieces

sont presentes.

• Hotte avec ventilateur et lampes installes

• Deflecteur pour installation sans decharge a I'exterieur

(recyclage)

• Raccord de transition en plastique avec clapet anti-reflux

installe

• Sachet de documents

Installation dans une r_sidence mobile

L'installation de cette hotte doit satisfaire aux exigences de la

norme Manufactured Home Construction Safety Standards, Titre

24 CFR, partie 328 (anciennement Federal Standard for Mobile

Home Construction and Safety, Titre 24, HUD, partie 280);

Iorsque cette norme n'est pas applicable, I'installation doit

satisfaire aux criteres de la plus recente edition de la norme

Manufactured Home Installation 1982 (Manufactured Home

Sites, Communities and Setups) ANSI A225.1/NFPA 501A*, ou

des codes et reglements Iocaux.

Dimensions du produit Dimensions a respecter Iors de rinstallation

11%0"

10 13/16"

(27,5 crn)

llllllilllll

IIIIIIIIIIII

33 Vlo"

(84 cm)

_21211/4"

(54,0 cm)

rain.

33 IAo"

(84,0 cm)

max.

2 3/8"

(6 cm)

10" 2" (5,1 cm) rain.

(254cm) 7" (17,8 cm) min.

\ _ (installations sans d_charge

.... _ rext_rieur SEULEMENT)

Placard

lateral

30" (76,2 cm) rnin.

36" (91,4 crn) max.

entre la base de

la hotte et la surface

de cuisson

35 _&"

(90 crn) rnin.

Axe central

Placard

lateral

21 W'

(54cm)

I'RIn.

33 V_d'

16%" (84 crn)

(42,3cm) m_

rnln.

33 _/_6"

(84,0 cm)

max.

16%"

(42,3 crn)

3 15/16H

(10sin)

• Le syst@me d'@vacuation doit d@charger I'air a I'ext@rieur,

except@ pour les installations sans d@charge a I'ext@rieur.

• Ne pas terminer le conduit d'@vacuation dans un grenier ou

dans un autre espace ferm&

• Ne pas utiliser une bouahe de d@aharge murale de

4" (10,2 am) normalement utilis@e pour un @quipement

de buanderie.

• Utiliser un conduit m_tallique uniquement. Un conduit en

m_tal rigide est recommand& Ne pas utiliser de conduit de

plastique ou de m_tal tr_s mince.

• Le systeme d'evacuation doit comporter un clapet. Si la

bouche de decharge murale ou par le toit comporte un

clapet, ne pas utiliser le clapet fourni avec la hotte de

cuisiniere.

Pour un fonctionnement efficace et silencieux :

• Utiliser autant que possible des sections droites et minimiser

le nombre de coudes.

Ne pas utiliser plus de trois coudes & 90°.

Veiller & ce qu'il y ait une section droite de conduit de

24" (61 cm) ou plus entre deux coudes, si on doit utiliser plus

de un raccord coud&

• Ne pas installer 2 coudes ensemble.

• Au niveau de chaque jointure du conduit de decharge,

assurer I'etancheite avec des brides.

• Autour de la bouche de decharge a I'exterieur, assurer

I'etancheite avec un produit de calfeutrage.

• La taille du conduit doit 6tre uniforme.

Installations pour r_gions & climat froid

On doit installer un clapet anti-reflux additionnel pour minimiser

le reflux d'air froid. Un el6ment non m6tallique d'isolation

thermique doit _tre installe pour minimiser la conduction des

temperatures exterieures par I'interm6diaire du conduit

d'evacuation. Le clapet anti-reflux doit _tre place du c6te air froid

par rapport & I'el6ment d'isolation thermique.

L'el6ment d'isolation thermique doit _tre aussi proche que

possible de I'endroit oQ le systeme d'evacuation s'introduit dans

la partie chauffee de la maison.

Renouvellement de I'air

Le code du bAtiment local peut exiger I'emploi d'un systeme

d'appoint d'air Iors de I'emploi d'un ventilateur d'extraction dont

la capacite d'aspiration est superieure &un debit (pieds cubes

par minute) specifi& Le debit specifi6, pieds cubes par minute,

est variable d'une juridiction & une autre. Consulter un

professionnel des installations de chauffage ventilation/

climatisation au sujet des exigences specifiques applicables

dans la juridiction locale.

M6thodes d'_vacuation

Cette hotte est configuree & I'usine pour la decharge de I'air

aspire a travers le toit ou & travers un mur.

Un circuit d'evacuation en conduit rond de 6" (15,2 cm) est

necessaire pour I'installation (non fourni). La hotte comporte une

ouverture de sortie de diam_tre 6" (15,2 cm).

REMARQUE • On deconseille I'emploi d'un conduit flexible. Un

conduit flexible peut causer une retro-pression et des

turbulences de I'air, ce qui reduit considerablement la

performance.

La sortie a I'exterieur du circuit d'evacuation peut se faire &

travers le toit ou &travers un mur. Pour la sortie atravers un mur,

on doit employer un raccord coude & 90°.

D6charge par I'arri_re

Le raccord coude & 90 ° peut _tre installe imm6diatement au-

dessus de la hotte.

Installation sans d_charge & I'ext_rieur (recyclage)

S'il n'est pas possible d'evacuer les fumees et vapeurs de

cuisson & I'exterieur, on peut employer la version "installation

sans decharge & I'exterieur (recyclage)" de la hotte dotee d'un

filtre & charbon actif et du deflecteur. Les vapeurs/fum6es sont

alors recyclees a travers la grille superieure.

D_charge a D_charge

travers le toit travers le mur

Installation sans

d_charge a I'ext_rieur

(recyclage)

A. Bouche de A. Bouche de A. D_flecteur

d_charge sur toit d_charge murale B. Conduit dia.

B. Conduit dia. B. Conduit dia. 6" (15,2 cm)

6" (15,2 cm) 6" (15,2 cm)

Calcul de la Iongueur effective du circuit d'_vacuation

Pour calculer la Iongueur effective du circuit d'evacuation

necessaire, additionner les Iongueurs equivalentes (pieds/m_tres)

de tousles composants utilises dans le systeme.

Composant Conduit de diam_tre

6" (15,2 cm)

coude & 45° 2,5 pi

(0,8m)

coude & 90° 5 pi

(1,5m)

La Iongueurequivalente maximum est de 35 pi (10,7cm).

Exemple de syst_me de d_charge

Bouche de

Coude _ 90° I___ 6pi(1,8rn)-_ decharge murale

Dans I'exemple suivant, la Iongueur theorique du circuit est

inferieure au maximum de 35 pi (10,7 m).

1 -coudea90 ° =5pi(1,5m)

1 - bouche de = 0 pi (0 m)

decharge murale

section droite de = 8 pi (2,4 m)

8 pi (2,4 m)

Longueur du systeme = 13 pi (3,9 m)

IMPORTANT : Observer les dispositions de tousles codes et

reglements en vigueur. Conserver les instructions d'installation

pour consultation par I'inspecteur des installations electriques.

C'est au client qu'incombe la responsabilite de contacter un

electricien qualifie et de veiller &ce que I'installation electrique

soit adequate et realisee en conformite avec les prescriptions de

la plus recente edition de la norme National Electrical Code,

ANSI/NFPA 70, ou de la norme CSA C22.1-94, Code canadien de

I'electricite, partie 1 et C22.2 N° 0-M91, et de tous les codes et

reglements Iocaux en vigueur.

Si les codes le permettent et si on utilise un conducteur distinct

de liaison &la terre, il est recommande qu'un electricien qualifie

verifie la qualite de la liaison & la terre.

Pour obtenir un exemplaire de la norme des codes ci-dessus,

contacter :

National Fire Protection Association

One Batterymarch Park

Quincy, MA 02269

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

• L'appareil dolt etre alimente par un circuit de 120 V,60 Hz,

CA seulement, 15 amperes, protege par fusible.

• Ne pas utiliser une tuyauterie de gaz pour le raccordement &

la terre.

En cas de doute quanta la qualite de la liaison & la terre de la

hotte de la cuisiniere, consulter un electricien qualifi&

Ne pas installer un fusible dans le conducteur neutre ou le

conducteur de liaison & la terre.

La hotte dolt etre raccordee au reseau electrique uniquement

avec des conducteurs de cuivre.

La hotte dolt etre raccordee directement au coupe-circuit

avec fusible ou au disjoncteur par I'intermediaire de c&ble &

conducteurs de cuivre, & blindage metallique flexible ou &

gaine non-metallique. IIest recommande de raccorder la

hotte sur un circuit distinct exclusif & cet appareil.

• Le calibre des conducteurs (cuivre seulement) et les

connexions doivent etre compatibles avec la demande de

courant de I'appareil specifiee sur la plaque signaletique. La

plaque signaletique de I'appareil est situee derriere le filtre,

sur la paroi arriere de la hotte.

• Le calibre des conducteurs dolt satisfaire les exigences de la

plus recente edition de la norme National Electrical Code,

ANSI/NFPA 70, ou de la norme CSA C22.1-94, Code

canadien de I'electricite, partie 1 et C22.2 N° 0-M91 et de

tousles codes et reglements en vigueur.

• Un serre-c&ble de 1/2"(12,7 mm) (homologation UL ou CSA)

dolt etre installe a chaque extremite du c&ble d'alimentation

(sur la hotte et sur le boitier de distribution).

INSTRUCTIONSD'INSTALLATION

R) 6 w}sdo de

On recommande que le circuit d'evacuation soit installe avant

I'installation de la hotte.

On ne dolt couper un poteau de colombage ou une solive

que si c'est absolument necessaire. Dans ce cas, on devra

construire une structure de support appropriee.

Avant d'executer les decoupages, verifier la disponibilite d'un

espace de passage suffisant dans le plafond ou lemur pour

le conduit d'evacuation.

Avant de selectionner la hotte & installer, mesurer la hauteur

libre sous plafond et la hauteur maximum disponible sous la

hotte.

3. Selectionner une surface plane pour I'assemblage de la

hotte. Recouvrir cette surface d'un materiau de protection.

Risque du poids excessif

Utiiiser deux ou plus de personnes pour d_piacer et

installer la hotte de la cuisini_re.

Le non=respect de cette instruction peut causer

une blessure au dos ou d'autre blessure.

Risque du poids excessif

Utiiiser deux ou plus de personnes pour d_piacer et

installer la cuisini_re.

Le non=respect de cette instruction peut causer

une blessure au dos ou d'autre blessure.

1. Si possible, deconnecter la cuisiniere autonome ou

encastree, et deplacer celle-ci hors de I'espace d'installation

entre les placards, pour faciliter I'acces au mur arriere. Sinon,

placer une epaisse couverture de protection sur le plan de

travail, la cuisiniere ou latable de cuisson pour la protection

contre les dommages ou souillures.

2. Determiner la methode d'extraction &utiliser : decharge &

travers lemur ou le toit, ou recyclage.

4. A I'aide de deux personnes ou plus, soulever la hotte de la

cuisiniere et la poser sur une surface de protection.

5. Determiner et marquer la position de I'axe central sur le mur

oQ la hotte sera installee.

6. Choisir une hauteur de montage - minimum 30" (76,2 cm) et

maximum suggere 36" (91,4 cm) - au-dessus de la cuisiniere

jusqu'au fond de la hotte et tracer une ligne de reference sur

lemur.

REMARQUE : Pour une configuration d'installation avec

hauteur sous plafond reduite (installation avec ou sans

decharge & I'exterieur), la hotte peut etre installee avec la

section superieure du cache-conduit.

7. Fixer le gabarit en place avec du ruban adhesif; aligner I'axe

central du gabarit et le bas du gabarit avec la ligne

correspondant au bas de la hotte, et avec I'axe central dej&

trace sur le mur.

La page charge ...

IKEA IH5303SS0 Guide d'installation

Marque: IKEA

Modèle: IH5303SS0

Catégorie: Hottes

Taper: Guide d'installation

Ce manuel convient également à

IH5303WS0

Télécharger le PDF

rapport

dans d''autres langues

English: IKEA IH5303SS0 Installation guide

IKEA IH5303SS0 Guide d'installation

Ce manuel convient également à

IKEA IH5303SS0 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents