Arrow ROT3200K-A Manuel utilisateur

PMROT3200K-A-8 Rev 09/21

Arrow™ ROT3200K-A

Rotary Tool

Outil rotatif

Herramienta rotatoria

ROT3200K-A

2

ROT3200K-A

ROTARY TOOL

ENGLISH

GENERAL POWER TOOL SAFETY WARNINGS 2–5

SPECIFIC WARNINGS & SAFETY RULES 6-10

DEFINITION OF SYMBOLS USED ON TOOL 11

ASSEMBLY 12-13

POWER TOOL OPERATION 14

WARRANTY 15

FRANÇAIS

AVERTISSEMENTS DE SÉCURITÉ D’ORDRE GÉNÉRAL

POUR LES OUTILS ÉLECTRIQUES 16–18

AVERTISSEMENTS ET RÈGLES DE SÉCURITÉ PARTICULIERS 19-23

DÉFINITION DES SYMBOLES SUR L’OUTIL 24

ASSEMBLAGE 25-26

FONCTIONNEMENT DE L’OUTIL ÉLECTRIQUE 27

GARANTIE 28

ESPANOL

ADVERTENCIAS GENERALES PARA SEGURIDAD DE

HERRAMIENTAS ELÉCTRICAS 29–31

ADVERTENCIAS ESPECÍFICAS Y REGLAS DE SEGURIDAD 32-36

DEFINICIÓN DE SÍMBOLOS UTILIZADOS EN LA HERRAMIENTA 37

ENSAMBLAJE 38-39

OPERACIÓN DE LA HERRAMIENTA ELÉCTRICA 40

GARANTÍA 41

To avoid eye injury always wear safety glasses when operating

the tool.

Pour éviter des blessures aux yeux toujours porter des lunettes

de sécurité en utilisant l’outil.

Para evitar lesiones en los ojos siempre use anteojos de

seguridad cuando utilice esta herramienta.

Obey all safety messages that follow this

symbol to avoid possible injury or death.

Respecter tous les messages de sécurité

suivant ce symbole pour éviter tout

risque de blessures ou de décès.

Observe todos los mensajes de

seguridad que aparecen junto a este

símbolo para evitar posibles lesiones o

la muerte.

To avoid loss of hearing, always wear

ear protection when operating the tool.

Pour éviter tout risque de perte

auditive, toujours porter des protecteurs

d’oreilles en utilisant l’outil.

A fin de evitar pérdida de la audición,

siempre use protección para los oídos

cuando utilice esta herramienta.

To avoid injury and misuse, please read

the instruction manual before operation.

Pour éviter tout risque de blessures et

une mauvaise utilisation, prière de lire

le manuel d’utilisation avant l’utilisation.

A fin de evitar lesiones y mal uso, lea el

manual de instrucciones antes de usar

la herramienta.

3

GENERAL POWER TOOL SAFETY WARNINGS

WARNING Read all safety warnings and all instructions. Failure to follow the warnings and instructions may

result in electric shock, re and/or serious injury. Save all warnings and instructions for future reference.

WORK AREA SAFETY

• Keep work area clean and well lit. Cluttered

or dark areas invite accidents.

• Do not operate power tools in explosive

atmospheres, such as in the presence of

ammable liquids, gases or dust. Power tools

create sparks, which may ignite the dust or fumes.

• Keep children and bystanders away while

operating a power tool. Distractions can cause

you to lose control.

ELECTRICAL SAFETY

• Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools. Unmodied plugs and matching outlets will reduce

risk of electric shock.

• Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric

shock if your body is earthed or grounded.

• Do not expose power tools to rain or wet

conditions. Water entering a power tool will increase

the risk of electric shock.

• Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges or

moving parts. Damaged or entangled cords increase

the risk of electric shock.

• When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of

a cord suitable for outdoor use reduces the risk of electric

shock.

• If operating a power tool in a damp location

is unavoidable, use a ground fault circuit

interrupter (GFCI) protected supply. Use of an

GFCI reduces the risk of electric shock.

The term “power tool” in the warnings refers to your mains-operated (corded) power tool.

4

PERSONAL SAFETY

• Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired

or under the inuence of drugs, alcohol or

medication. A moment of inattention while operating

power tools may result in serious personal injury.

• Use personal protective equipment. Always

wear eye protection. Protective equipment such as

a dust mask, non-skid safety shoes, hard hat or hearing

protection used for appropriate conditions will reduce

personal injuries.

• Prevent unintentional starting. Ensure the

switch is in the off-position before connecting

to power source, picking up or carrying the

tool. Carrying power tools with your nger on the

switch or energizing power tools that have the switch on

invites accidents.

• Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may result

in personal injury.

• Do not overreach. Keep proper footing and

balance at all times.

This enables better control of the power tool in

unexpected situations.

• Dress properly. Do not wear loose clothing or

jewelry. Keep your hair and clothing away

from moving parts.

Loose clothes, jewelry or long hair can be caught in

moving parts.

• If devices are provided for the connection of

dust extraction and collection facilities, ensure

these are connected and properly used.

Use of dust collection can reduce dust-related hazards.

• Do not let familiarity gained from frequent use

of tools allow you to become complacent and

ignore tool safety principles.

A careless action can cause severe injury within a

fraction of a second.

POWER TOOL USE AND CARE

• Do not force the power tool. Use the correct

power tool for your application. The correct power

tool will do the job better and safer at the rate for which it

was designed.

• Do not use the power tool if the switch does

not turn it on and off. Any power tool that cannot

be controlled with the switch is dangerous and must be

repaired.

• Disconnect the plug from the power source, if

detachable, from the power tool before making

any adjustments, changing accessories, or

storing power tools. Such preventive safety measures

reduce the risk of starting the power tool accidentally.

• Store idle power tools out of the reach of

children and do not allow persons unfamiliar

with the power tool or these instructions to

operate the power tool. Power tools are dangerous

in the hands of untrained users.

GENERAL POWER TOOL SAFETY WARNINGS

5

• Maintain power tools and accessories. Check

for misalignment or binding of moving parts,

breakage of parts and any other condition

that may affect the power tool’s operation.

If damaged, have the power tool repaired

before use. Many accidents are caused by poorly

maintained power tools.

• Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to control.

• Use the power tool, accessories and tool bits

etc. in accordance with these instructions,

taking into account the working conditions

and the work to be performed.

Use of the power tool for operations different from

those intended could result in a hazardous situation.

• Keep handles and grasping surfaces dry,

clean and free from oil and grease.

Slippery handles and grasping surfaces do not allow

for safe handling and control of the tool in unexpected

situations.

• Do not expose the tool to re or excessive

temperature. Exposure to re or temperature above

265 °F (130 °C) may cause explosion.

GENERAL POWER TOOL SAFETY WARNINGS

Have your power tool serviced by a qualied

repair person using only identical replacement

parts. This will ensure that the safety of the power tool is

maintained.

WARNING! To reduce the risk of injury, use only

accessories rated at least equal to the maximum speed

marked on the tool.

WARNING! To reduce the risk of injury, use accessories

rated for the operating speed setting of the tool.

SERVICE

6

Safety Warnings Common for Grinding, Sanding,

Wire Brushing, Polishing or Abrasive Cutting-Off

Operations:

This power tool is intended to function as a grinder, sander,

wire brush, polisher or cut-off tool.

Read all safety warnings, instructions, illustrations and

specications provided with this power tool. Failure to follow

all instructions listed below may result in electric shock, re

and/or serious injury. Do not use accessories which are

not specically designed and recommended by the tool

manufacturer. Just because the accessory can be attached

to your power tool, it does not assure safe operation. The

rated speed of the accessory must be at least equal to the

maximum speed marked on the power tool. Accessories

running faster than their RATED SPEED can break and

y apart. The outside diameter and the thickness of your

accessory must be within the capacity rating of your power

tool. Incorrectly sized accessories cannot be adequately

guarded or controlled. The arbor size of wheels, anges,

backing pads or any other accessory must properly t the

spindle of the power tool. Accessories with arbor holes

that do not match the mounting hardware of the power tool

will run out of balance, vibrate excessively, and may cause

loss of control. Do not use a damaged accessory. Before

each use inspect the accessory such as abrasive wheels for

chips and cracks, backing pad for cracks, tear or excess

wear, wire brush for loose or cracked wires. If power tool

or accessory is dropped, inspect for damage, or install

an undamaged accessory. After inspecting and installing

an accessory, position yourself and bystanders away from

SPECIFIC SAFETY RULES FOR ROTARY TOOL the plane of the rotating accessory and run the power

tool at maximum no-load speed for one minute. Damaged

accessories will normally break apart during this test

time. Wear personal protective equipment. Depending on

application, use face shield, safety goggles or safety glasses.

As appropriate, wear dust mask, hearing protectors, gloves,

and workshop apron capable of stopping small abrasive or

workpiece fragments. The eye protection must be capable of

stopping ying debris generated by various operations. The

dust mask or respirator must be capable of ltrating particles

generated by your operation. Prolonged exposure to high

intensity noise may cause hearing loss. Keep bystanders

a safe distance away from work area. Anyone entering

the work area must wear personal protective equipment.

Fragments of workpiece or of a broken accessory may y

away and cause injury beyond immediate area of operation.

Hold the power tool by insulated gripping surfaces only,

when performing an operation where the cutting accessory

may contact hidden wiring. Contact with a “live” wire will

also make exposed metal parts of the power tool “live” and

could give the operator an electric shock. Never lay the

power tool down until the accessory has come to a complete

stop. The spinning accessory may grab the surface and pull

the power tool out of your control.

• Do not run the power tool while carrying it at your side.

Accidental contact with the spinning accessory could

snag your clothing, pulling the accessory into your body.

• Regularly clean the power tool’s air vents. The motor’s

fan will draw the dust inside the housing and excessive

accumulation of powdered metal may cause electrical

hazards.

SPECIFIC WARNINGS AND SAFETY RULES

FOR ROTARY TOOL

7

KICKBACK AND RELATED WARNINGS

• Do not operate the power tool near ammable materials.

Sparks could ignite these materials.

• Do not use accessories that require liquid coolants. Using

water or other liquid coolants may result in electrocution or

shock.

the edge of the workpiece on both sides of the wheel.

• Use extra caution when making a “pocket cut” into

existing walls or other blind areas. The protruding wheel

may cut gas or water pipes, electrical wiring or objects

that can cause kickback.

Kickback is a sudden reaction to a pinched or snagged

rotating wheel, backing pad, brush or any other accessory.

Pinching or snagging causes rapid stalling of the rotating

accessory which in turn causes the uncontrolled power tool to

be forced in the direction opposite of the accessory’s rotation

at the point of the binding. For example, if an abrasive

wheel is snagged or pinched by the workpiece, the edge of

the wheel that is entering into the pinch point can dig into the

surface of the material causing the wheel to climb out or kick

out. The wheel may either jump toward or away from the

operator, depending on direction of the wheel’s movement at

the point of pinching. Abrasive wheels may also break under

these conditions. Kickback is the result of power tool misuse

and/or incorrect operating procedures or conditions and can

be avoided by taking proper precautions as given below.

• Do not restart the cutting operation in the workpiece. Let

the wheel reach full speed and carefully re-enter the cut.

The wheel may bind, walk up or kickback if the power tool

is restarted in the workpiece.

• Support panels or any oversized workpiece to minimize

the risk of wheel pinching and kickback. Large workpieces

tend to sag under their own weight. Supports must be

placed under the workpiece near the line of cut and near

SPECIFIC WARNINGS AND SAFETY RULES

FOR ROTARY TOOL

8

SPECIFIC WARNINGS AND SAFETY RULES

FOR ROTARY TOOL

Safety Warnings Specic for Sanding

Operations:

• Do not use excessively oversized sanding disc paper.

Follow manufacturers recommendations, when selecting

sanding paper. Larger sanding paper extending beyond

the sanding pad presents a laceration hazard and may

cause snagging, tearing off the disc or kickback.

Safety Warnings Specic for Polishing Operations:

• Do not allow any loose portion of the polishing bonnet or

its attachment strings to spin freely. Tuck away or trim any

loose attachment strings. Loose and spinning attachment

strings can entangle your ngers or snag on the

workpiece.

Safety Warnings Specic for Wire Brushing

Operations:

• Be aware that wire bristles are thrown by the brush even

during ordinary operation. Do not overstress the wires by

applying excessive load to the brush. The wire bristles can

easily penetrate light clothing and/or skin.

• If the use of a guard is recommended for wire brushing, do

not allow any interference of the wire wheel or brush with

the guard. Wire wheel or brush may expand in diameter

due to workload and centrifugal forces.

Additional Safety Warnings

• The arbor size of wheels, sanding drum or any other

accessory must properly t the spindle or collet of the

power tool. Accessories that do not match the mounting

hardware of the power tool will run out of balance, vibrate

excessively and may cause loss of control.

• Mandrel mounted wheels, sanding drums, cutters or other

accessories must be fully inserted into the collet or chuck.

The “overhang” or the length of the mandrel from the

wheel to the collet must be minimal. If the mandrel is

insufciently held and/or the overhang of the wheel is too

long, the mounted wheel may become loose and ejected

at high velocity.

• After changing the bits or making any adjustments, make

sure the collet nut, chuck or any other adjustment devices

are securely tightened. Loose adjustment devices can

unexpectedly shift, causing loss of control, loose rotating

components will be violently thrown.

• Maintain a rm grip on the power tool and position your

body and arm to allow you to resist kickback forces.

Always use auxiliary handle, if provided, for maximum

control over kickback or torque reaction during start-up.

The operator can control torque reactions or kickback

forces, if proper precautions are taken.

• Never place your hand near the rotating accessory.

Accessory may kickback over your hand.

• Do not position your body in the area where power tool

will move if kickback occurs. Kickback will propel the tool

in direction opposite to the wheel’s movement at the point

of snagging.

• Use special care when working corners, sharp edges etc.

Avoid bouncing and snagging the accessory. Corners,

sharp edges or bouncing have a tendency to snag the

rotating accessory and cause loss of control or kickback.

9

SPECIFIC WARNINGS AND SAFETY RULES

FOR ROTARY TOOL

• Do not attach a saw chain woodcarving blade or toothed

saw blade. Such blades create frequent kickback and loss

of control.

Safety Warnings Specic for Grinding and

Abrasive Cutting-Off Operations:

• Use only wheel types that are recommended for your

power tool and the specic guard designed for the

selected wheel. Wheels for which the power tool was not

designed cannot be adequately guarded and are unsafe.

• Wheels must be used only for recommended applications.

For example: do not grind with the side of cut-off wheel.

Abrasive cut-off wheels are intended for peripheral

grinding, side forces applied to these wheels may cause

them to shatter.

• Always use undamaged wheel anges that are of correct

size and shape for your selected wheel. Proper wheel

anges support the wheel thus reducing the possibility of

wheel breakazge. Flanges for cut-off wheels may be

different from grinding wheel anges.

• Do not use worn down wheels from larger power tools.

Wheel intended for larger power tool is not suitable for the

higher speed of a smaller tool and may burst.

Additional Safety Warnings Specic for Abrasive

Cutting-Off Operations:

• Do not “jam” the cut-off wheel or apply excessive

pressure. Do not attempt to make an excessive depth

of cut. Overstressing the wheel increases the loading and

susceptibility to twisting or binding of the wheel in the cut

and the possibility of kickback or wheel breakage.

• Do not position your body in line with and behind the

rotating wheel. When the wheel, at the point of operation,

is moving away from your body, the possible kickback

may propel the spinning wheel and the power tool directly

at you.

• When wheel is binding or when interrupting a cut for any

reason, switch off the power tool and hold the power tool

motionless until the wheel comes to a complete stop. Never

attempt to remove the cut-off wheel from the cut while the

wheel is in motion otherwise kickback may occur.

Investigate and take corrective action to eliminate the

cause of wheel binding.

• Always feed the bit into the material in the same direction

as the cutting edge is exiting from the material (which is

the same direction as the chips are thrown). Feeding the

tool in the wrong direction causes the cutting edge of the

bit to climb out of the work and pull the tool in the

direction of this feed.

• When using steel saws, cut-off wheels, high speed cutters

or tungsten carbide cutters, always have the work securely

clamped. These wheels will grab if they become slightly

canted in the groove and can kickback. When a cut-off

wheel grabs, the wheel itself usually breaks. When the

steel saw, high-speed cutters, or tungsten carbide cutter

grab, it may jump from the groove and you could lose

control of the tool.

• Do not position your hand in line with and behind the

rotating wheel. When the wheel, at the point of operation,

WARNING! Some dust created by power sanding,

sawing, grinding, drilling, and other construction activities

contains chemicals known to cause cancer, birth defects or

other reproductive harm. Some examples of these chemicals

are:

• lead from lead-based paint

• crystalline silica from bricks and cement and other

masonry products, and

• arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how

often you do this type of work. To reduce your exposure to

these chemicals: work in a well ventilated area, and work

with approved safety equipment, such as those dust masks

that are specially designed to lter out microscopic particles.

10

SPECIFIC WARNINGS AND SAFETY RULES

FOR ROTARY TOOL

is moving away from your hand, the possible kickback

may propel the spinning wheel and the power tool

directly at you.

• Allow brushes to run at operating speed for at least one

minute before using them. During this time no one is to

stand in front or in line with the brush. Loose bristles or

wires will be discharged during the run-in time.

• Direct the discharge of the spinning wire brush away

from you. Small particles and tiny wire fragments may be

discharged at high velocity during the use of these brushes

and may become imbedded in your skin.

WARNING! To reduce the risk of injury in applications

that produce a considerable amount of dust, use an OSHA

compliant dust extraction solution in accordance with the

solution’s operating instructions. Always use common sense

and be cautious when using tools. It is not possible to

anticipate every situation that could result in a dangerous

outcome. Do not use this tool if you do not understand these

operating instructions or you feel the work is beyond your

capability, contact Arrow Fastener or a trained professional

for additional information or training.

• Maintain labels and nameplates. These carry important

information. If unreadable or missing, contact Arrow

Fastener for a free replacement.

11

DEFINITION OF SYMBOLS USED ON TOOL

SYMBOLS FUNCTIONAL DESCRIPTION WARNING! Only use accessories

specically recommended for this tool.

Others may be hazardous

1

2

3

4

6

7

5

12

ASSEMBLY

Shaft

Lock

Button

Collet

Nut

To

Loosen

To

Tighten

Collet

Wrench

13

ASSEMBLY

WARNING! Always unplug rotary tool before changing

accessories and servicing your tool.

CAUTION Do not engage lock while the ROTARY TOOL

is running.

PLACING ACCESSORIES INTO THE TOOL

Always switch the tool off rst. Hold the locking button at the

front of the tool down and undo the collet chuck

(anti-clockwise). Insert the collet that matches the shaft size

of the accessory to be used. Place the collet nut over the

collet and then insert the accessory shaft into the collet chuck

ensuring maximum shaft contact. Then tighten up the

collet nut.

COLLET NUT

To loosen, rst press Shaft Lock Button and rotate the shaft

by hand until the lock engages the shaft preventing further

rotation.

CAUTION Do not engage lock while the ROTARY TOOL

is running.

With the shaft lock engaged use the collet wrench to

loosen the collet nut, if necessary, the collet nut must be

loosely threaded on when inserting an accessory. Change

accessories by inserting the new one into the collet as far as

possible to minimize runout and unbalance. With the shaft

lock engaged, nger tighten the collet nut until the accessory

shank is gripped by the collet. Avoid excessive tightening of

the collet nut when there is no accessory inserted.

(DO NOT USE PLIERS).

COLLETS

Two different size collets to accommodate different shank

sizes are available for your Rotary Tool. To install a different

collet, remove the collet nut and remove the old collet. Insert

the unslotted end of the collet in the hole in the end of the

tool shaft. Replace collet nut on the shaft

1/8” Collet (Included and installed on the tool)

3/32” Collet (is included in the accessory kit)

Always switch the tool off rst. Hold the locking button at

the front of the tool down and undo the collet chuck (anti-

clockwise). Insert the collet that matches the shaft size of the

accessory to be used. Place the collet nut over the collet and

then insert the accessory shaft into the collet chuck ensuring

maximum shaft contact. Then tighten up the collet nut.

CAUTION Always use the collet which matches the shank

size of the accessory you plan to use. Never force a larger

diameter shank into a collet.

To maintain balance on abrasive wheel points, before each

use, with the wheel point secured in the collet, turn on the

Rotary Tool and run the Dressing Stone lightly against the

revolving wheel point. This removes high spots and trues up

the wheel point for good balance.

WARNING! Only use accessories specically

recommended for this tool. Others may be hazardous. Only

use accessories with Maximum Safe Operating Speed rated

at least equal to the maximum speed marked on the power

tool. This speed is based on the strength of the accessory,

14

allowing for a reasonable measure of safety. It is not meant

to imply a best or most efcient operating speed. Do not

exceed the Maximum Safe Operating Speed. To reduce

the risk of injury, always clean mandrels before inserting

them into the collet and securely tighten the collet nut.

Otherwise the high-speed rotation of the tool could force the

accessory to y out of the collet. Everyone in the area must

wear protective clothing and safety goggles or face shields.

Damaged accessories may y apart with considerable force,

causing potential for serious injury. Always use the collet

which matches the shank size of the accessory you plan to

use. Never force a larger diameter shank into a collet.

INSTALLING/REMOVING ACCESSORIES

1. Switch tool off and unplug.

2. Hold the spindle lock down and loosen the collet chuck

(turn counter-clockwise).

3. Insert the collet into the spindle.

4. Loosely screw the collet nut onto the spindle.

5. Insert the accessory shank into the collet.

6. Press in the spindle lock button and tighten the collet nut

securely using the collet wrench.

7. To release accessory, hold the spindle lock down and

loosen the collet chuck. (turn counter-clockwise)

ASSEMBLY

WARNING! (cont.)

Starting / Stopping

Make sure the tool is off before plugging into power source.

“O” position is off the “I” position is on.

1. To start the tool, grasp the handle and slide the switch

forward to the ON (I) position.

2. Allow the tool to come to full speed before beginning

work.

3. Control pressure and surface contact between accessory

and workpiece.

4. To stop the tool, slide the switch back to the OFF (O)

position. Make sure the tool comes to a complete stop

before laying the tool down.

Selecting Speed

To set the maximum speed, rotate the speed dial. Set the

speed dial to “1” for the lowest speed (10,000 OPM). Set

the speed dial to “6” for the highest speed (35,000 OPM).

15

ACCESSORIES

BALANCING ACCESSORIES

To true up or balance an accessory, slightly loosen collet nut

and give the accessory or collet a 1/4 turn. Re tighten collet

nut and run the Rotary Tool .To maintain balance on abrasive

wheel points, before each use, with the wheel point secured

in the collet, turn on the Rotary Tool and run the Dressing

Stone lightly against the revolving wheel point. This removes

high spots and trues up the wheel point for good balance.

USING ACCESSORIES

There are a variety of attachments supplied with this tool.

Some of these come ready to use and can be tted to the

tool without any further assembly. However, others require

tting to a mandrel before they can be used. Here is a list of

accessories.

Uses Accessory Included with Kit Accessory Mandrel used with Accessory

Cutting Abrasive Cutting Discs

8 pcs 1” (24mm) cut-off wheels 0.024-inch

(0.6mm) Thickness

Sanding 4pcs 1/2“(12.5mm) sanding bands

1pc 1/2“ (12.5mm) sanding drum

Sanding 3pcs ¾” (20mm) sanding papers

Polishing

Wheels 2 pc 1” (25mm) polishing wool wheels

2 pcs 1/2“(12.5mm) polishing wool wheels

Grinding 10pcs aluminum oxide grinding stones

2pcs diamond grinder bits

1pc 1” (25mm) grindstone

Drilling 2pcs HSS twist drill bits

NONE

16

ACCESSORIES

Polishing:

Use the mandrel for polishing/wool wheel

1. Push the threaded point of the polishing/wool wheel

mandrel into the required polishing wheel.

2. Twist the mandrel anticlockwise to secure the polishing

wheel rmly on to the mandrel.

3. Fit the mandrel to the tool as described in “Fitting the

Attachments”.

4. Occasionally check the wheel during use to ensure it is

still secure.

Cut off wheel and sanding papers:

Use the Mandrel for polishing/cut-off wheel

1. Push the threaded point of the Polishing / cut off wheel

mandrel into the required cut off wheel or sanding paper.

2. Twist the arbor anticlockwise to secure the cut off wheel or

sanding paper rmly on to the mandrel.

3. Fit the mandrel to the tool as described in “Fitting the

Attachments”.

4. Occasionally check the cut off wheel or sanding paper

during use to ensure it is still secure.

Sanding Drums:

Use the Sanding Drum Mandrel

1. To t a disc to the Sanding Drum mandrel, unscrew the

tting screw.

2. Remove the screw, washer and rubber drum holder.

3. Push the required Sanding Drum on to the rubber drum

holder.

4. Ensure that the drum is completely pushed on to the holder

so that edges of the drum and holder are aligned.

5. Replace the drum holder on the arbor.

6. Replace the washer and screw.

7. Tighten the screw until the disc is rmly secured.

8. Fit the mandrel to the tool as described in “Fitting the

Attachments”.

17

POWER TOOL OPERATION

Using the Rotary Tool

This rotary tool can be used for drilling, grinding, sanding

and polishing, as well as engraving, cutting and removing

rust in tight spaces or inaccessible places. The tool can be

used on most metals, glass, wood and ceramics. For best

performance and results keep the speed as even as possible

without exercising too much pressure. As a guideline, use the

tool at low speed for all large accessories, such as polishing

for example, and at high speed for smaller accessories such

as those used for engraving. For grinding and engraving,

hold the tool as if it were a pen. Move the tool in the same

direction as the bit is spinning (as indicated by the arrow

near the front of the tool). Moving the tool in the opposite

direction can cause the tool to kickback, ending up in loss of

control and damage to the workpiece.

The maximum recommended diameter of MOUNTED

WHEELS, threaded CONES AND PLUGS shall not exceed

55 mm and that the maximum recommended diameter of

sanding accessories shall not exceed 80 mm

Starting / Stopping

Make sure the tool is off before plugging into power source.

“O” position is off the “I” position is on.

1. To start the tool, grasp the handle and slide the switch

forward to the ON (I) position.

2. Allow the tool to come to full speed before beginning

work.

3. Control pressure and surface contact between accessory

and workpiece.

4. To stop the tool, slide the switch back to the OFF (O)

position. Make sure the tool comes to a complete stop

before laying the tool down.

Selecting Speed

To set the maximum speed, rotate the speed dial. Set the

speed dial to “1” for the lowest speed (10,000 OPM). Set

the speed dial to “6” for the highest speed (35,000 OPM).

NOTE: Speed is affected by voltage changes. A reduced

incoming voltage will slow the RPM of the tool.

USEFUL HINTS & TIPS

1. Your rotary tool will become warm after prolonged use

and so must be switched off and allowed to cool down.

2. To ensure smooth running, the spindle should be oiled

periodically.

3. Do not apply too much radial pressure to the accessory

bits while polishing, cleaning, sanding or grinding. By

doing this you will put a strain on the spindle and

adversely affect the precision of the tool.

4. Always work with a sensitive touch so as not to impede

the efciency of your mini tool.

5. When drilling metal, always mark the drilling point with a

center punch rst, so that your rotary tool does not slip.

18

6. Always ensure that you have maximum contact between

the accessory shaft and the collet chuck.

7. Vary the speed on the tool for the work in hand, eg. Low

speed for polishing and cleaning and high speed for

engraving.

POWER TOOL OPERATION

Uses Speciﬁcations

Cutting 8 pcs 1” (24mm) cut-off wheels 0.024-inch

(0.6mm) Thickness

Sanding 4pcs 1/2“(12.5mm) sanding bands

1pc 1/2“ (12.5mm) sanding drum

3pcs ¾” (20mm) sanding papers

Polishing 2 pc 1” (25mm) polishing wool wheels

2 pcs 1/2“(12.5mm) polishing wool wheels

Grinding 10pcs aluminum oxide grinding stones

2pcs diamond grinder bits

1pc 1” (25mm) grindstone

Mandrels

Collets 2pcs metal chucks: 0.095-inch (2.4mm)

0.125-inch (3.2mm)

1pcs mandrel for polishing/wool wheel

1pc mandrel for polishing/cut-off wheel

1pc wrench

Drilling 2pcs HSS twist drill bits

ACCESSORIES (INCLUDED WITH KIT)

USEFUL HINTS & TIPS (Cont.)

19

POWER TOOL OPERATION

AUXILLARY HANDLE

- Installation (Fig. 1&2)

- Proper Handling and Operation (Fig. 3-5)

CUTTING GUIDE

- Installation (Fig. 1-4)

- Fully Assembled Cutting Guide (Fig. 5)

- Operation (Fig. 6)

Features & Benets:

1. Provides accurate and controlled cutting.

2. Easily attaches to ROTARY TOOL.

3. Adjustable depth based on material thickness.

ATTACHMENTS (INCLUDED WITH KIT)

Features & Benets:

1. Ergonomic grip and comfort for detailed applications.

2. Angled bottom allows the operator to get closer to

the surface.

3. Transfers the weight of the tool to the palm of hand

for improved balance and control.

4. Able to remove housing cap and attach handle for

quick and easy modication.

Auxillary

Handle Cutting

Guide Protective

Shield

20

POWER TOOL OPERATION

PROTECTIVE SHIELD

- Remove Housing Cap (Fig. 1)

- Replace with Shield, and Tighten (Fig. 2)

- Adjust Shield to desired location (Fig. 3)

Features & Benets:

1. Equally suitable for use with either hand.

2. Easily adjusts to any position.

3. Provides a clear and simple solution for redirecting debris and

sparks away from the operator, without interfering with the task

at hand.

4. Angled bottom allows the operator to get closer to

the surface.

3. Transfers the weight of the tool to the palm of hand

for improved balance and control.

4. Able to remove housing cap and attach handle for

quick and easy modication.

La page charge ...

Arrow ROT3200K-A Manuel utilisateur

Arrow ROT3200K-A Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents