Molift Mover 300 Manuel utilisateur

Molift Mover 300

BM06199 Rev. A 2021-02-16

Contents

User manual - English - 3

Gebrauchsanweisung - Deutsch - 19

Brukermanual - Norsk - 35

Bruksanvisning - Svenska - 51

Käyttöohje - Suomi - 67

Manual utente - Italiano - 83

Manual d`utilisation - Francais - 99

Manual de usuarioo - Español - 115

Handleiding - Nederlands - 131

Brugsvejledning - Dansk - 147

Molift Mover 300

EN - User manual

BM06101 Rev. G 2021-02-16

User manual - English

Important

This user manual contains important safety

instructions and information regarding the use of

the lifter and accessories.

In this manual the user is the person being lifted.

The assistant is the person operating the lifter.

Warning!

This symbol indicates important

information related to safety.

Follow these instructions carefully.

Read user manual before use!

It is important to fully understand

the content of the user manual

before attempting to use the

equipment.

Visit www.etac.com to download documentation

to ensure you have the latest version.

English Manual

4

Molift Smart 150 / www.etac.com

Molift Mover 300

Molift Mover 300 is a mobile lifter intended for

lifting and transferring a person from/to bed, ﬂoor,

chair, wheelchair or toilet with a sling. The lifter

is made of light-weight materials, has castors and

electric actuator and is powered by a battery. It

has electrically adjustable legs and a lifting capac-

ity of 300 kg ( 661 lbs).

It is ideal for institutional care settings but can also

be used in privates homes and nursing homes. The

lifter should only be used for transfers across short

distances, such as between a chair and a bed or

into bathroom / rest room, and is not a replace-

ment for wheelchair or similar.

About Molift Mover 300

Lifter components:

Identiﬁcation of those parts into which the lifter

can be disassembled

Lifting arm

Push

handles

Motor /

actuator

Emergency

stop

Legs

Electric

emergency

lowering

Chassis

Sling bar

Battery

Lifting

column

Manual

emergency

lowering

Hand

control

Wheel / castor

(rear with break)

5

Molift Smart 150 / www.etac.com

ENNO DEFR ITES FI SVNLDA

Product identiﬁcation

General

Declaration of conformity

The Molift Mover 300 and related accessories described in this operator manual are CE

marked in accordance with EU Council Directive 93/42/EEC concerning medical devices, class

1, and has been tested and approved by a third party according to standards IEC 60601-1, IEC

60601-1-2 and NS-EN ISO 10535:2006.

Conditions for use

Lift and transfer of a person will always pose a certain risk and only trained personnel are allowed to use

the equipment and accessories covered by this user manual.

Modiﬁcations and use of components made by other manufacturers.

We recommend only using Molift components and spare parts. Declaration of conformity is not valid

and Etac is not responsible for warranty if any modiﬁcations are made to the product. Etac shall not be

liable for faults or accidents that can occur when using components made by other manufacturers.

Only certiﬁed personnel are allowed to open lifter or accessories to perform service

or repair. Risk of injury from rotating parts and electric shock.

The lifter is not intended to be operated by the person being lifted.

Warranty

2-year warranty against defects in workmanship and materials of our products.

For terms and conditions, see www.etac.com

Product label

The product labels barcode contain article number,

serial number and production date.

Warning labels and symbols

Symbols used on the product, explained in more

detail:

Type BF applied part Battery indicator

CE marked

60601-1

Certiﬁcation body mark

Refer to user manual

Manufacturer

Indoor use only

YYYY-MM-DD

Date of manufacture

Do not dispose in

general waste

Catalogue number

Emergency lowering

Serial number

Service indicator

Medical Device

6

Molift Smart 150 / www.etac.com

Safe Working Load (SWL):

300 kg (661 lbs)

Weight of unit:

Excl. battery and sling bar:

36 kg/79,3 lbs

Chassis: 19 kg/41,8 lbs

Lifting column: 17 kg/37,4 lbs

Battery: 1,6 kg/3,7 lbs

4-point medium sling bar: 2,5 kg/7,3 lbs

Battery:

Art: 1341000

26.4 V NiMH 2.6 Ah

Battery charger:

100-240 V AC, 50-60 Hz

0,9 A output

Lifting speed:

32,6mm/second (1,28 inches/second)

with 75kg (165,35 lbs) load

Protection class:

Hand control IP24

Lift motor IP24

Maximum A-weighted sound power level:

L

WA

= 63,2 dB

Operating forces button:

Buttons on handset: 3.4 N

Material:

Steel, aluminum, plastic

Motor:

Lifting motor/actuator: 24 V DC

Leg spreading motor: 12 V DC

Turning diameter:

1400 mm (55.1 inches)

Number of lifts with fully charged battery:

50 lifts ( 75 kg / 165 lbs, 50 cm / 20 inches)

Expected lifetime:

The lifter has an expected lifetime of 30 000

cycles or 10 years.

Technical data

2100 mm (82/in)

1285 mm (50/in)

115 mm

(

4/in)

1395 mm (82/in)

470 mm

(

4/in)

275 mm

(

10/in)

1065 mm

(

4/in)

1775 mm

(

69/in)

403 mm

(

15/in)

1250 mm (49/in)

550 mm (21/in)

690 mm (

27/in)

1065 mm (

41/in)

1205 mm (

47/in)

43 mm (1/in)

115 mm (

4/in)

w=700

M

K

2070 mm (81/in)

1420 mm (

55/in)650 mm (25/in)

620 mm (24/in)

CSP

1

2

3

2070 mm (81/in)

1340 mm (52

/in)

650 mm (25

/in)

1 Highest position:

2 Max reach:

3 Lowest position:

7

Molift Smart 150 / www.etac.com

ENNO DEFR ITES FI SVNLDA

Assembly

Charge the battery. The battery must not be in

the battery holder during assembly!

Lifting column

Place lifting column in chassis. Make sure that

the red arrow on the lower part of the column

corresponds with the edge of chassis.

Make sure screw on column is inside the hole

on chassis. This will prevent the column from

unintentionally being lifted out of chassis when

lock handle is pushed down.

Fix the column by pushing the lock handle on the

back all the way down.

Mounting sling bar

Turn connection point on lifting arm in top

position.

Insert bolt on sling bar in connection point to

mount sling bar. When bolt is completely inside

the sling bar is mounted and can rotate freely.

Battery and hand control

1.

1 32

Connect hand control to bottom of battery

holder.

2. Insert battery.

3. Connect hand control wire to push handle so

it does not fall to the ﬂoor when dropped.

Checklist after assembly

Do not start using lifter before

completing control according to

checklist after assembly.

Use this checklist to verify that the lifter is properly

installed and can operate correctly and safely

before use.

Ensure that the lifting arm, lifting column and

sling bar are properly ﬁxed and that there are

no loose parts on the lifter.

Make sure battery is charged (no lights on the

battery lamps).

Check that the lifter has no apparent damage

or other faults.

Perform one lift with load (60-80 kg)

8

Molift Smart 150 / www.etac.com

How to use Molift Mover 300

The hand control has 4 buttons for lifting and

lowering of lifting arm and leg spread mechanism

in and out.

The Hand control has an indicator

light that will illuminate when battery level is

low and the lifter requires charging

Hand control 4 buttons

Art. no. 2018004

Lifting arm - Up / Down

NB! The lifter is most unstable in top position.

Legs - In / Out

NB! Spreded legs provides increased stability and

better access to chair or toilet.

Hand control

General safety precautions

Only use accessories and slings that are adjusted

to ﬁt the user, type of disability, size, weight and

type of transfer.

Working pause ratio/Duty Cycle.

Molift Mover 300 should not be run constantly

for more than 2 minutes (with maximum load),

and rest for minimum 18 minutes. Duty Cycle

10%. (Intermittence according to standard ISO-EN

10535)

Safe Working Load

The lifter is marked with Safe Working Load (SWL)

The lowest SWL shall always be used

if safe working load (SWL) differs

between lifter, sling bar and body

support unit

Molift lifters shall only be used to lift

persons. Never use the lifter to lift or

move objects of any kind.

Inspection to be performed daily or before use:

Make sure lifter has no visible damage, defects

or deformations

Make sure sling bar connection and all detach-

able parts are properly connected and secured

Make sure battery indicator is not illuminated

and service light is green

Make sure sling strap does not have visible

damage or frays.

Make sure wheels are rolling freely and lifter is

easy to manouvre

Inspection to be performed monthly:

Test run lifters operation functions and make

sure lifter does not make any abnormal

sounds

Test emergency stop button and emergency

lowering

If there are any faults or defects, the lift needs to

be taken out of operation and marked ”out of

order”

Before use / Daily check / Monthly

9

Molift Smart 150 / www.etac.com

ENNO DEFR ITES FI SVNLDA

Safety devices

Molift Mover 300 is equipped with several safety

devices, which are intended to prevent damage or

injuries to personnel and equipment in the case of

incorrect use.

The lifter has an overload sensor preventing the

lifter to be operated if the load exceeds SWL.

The lifting arm is hinged to prevent the arm

and sling bar from squeezing the user. The

actuator will not produce any force when moving

downwards.

The electronics are disabled if overheated. Wait

until the lifter has cooled down before using it

again.

Push handles

Use the push handles to move the lifter.

Do not push or pull the user,

lifting arm or actuator.

This may cause stability prob-

lems and lifter may tip over.

The lifter shall only be used for movement

over short distances. It is not a replacement

for wheelchair or similar.

Brakes

Rear wheels/castors are equipped with brakes.

Step on lever to lock brakes. Flip up to unlock.

Emergency stop / Emergency lowering

Emergency stop

The emergency stop shuts off the power when

pushed in. Turn clockwise to reset (OK to operate

when the green ring is visible).

Electrical emergency lowering

Push and hold button for electrical emergency

lowering to lower lifting arm. The electrical emer-

gency lowering function does not work when the

emergency stop is activated.

Manual emergency lowering

Turn the top of the actuator clockwise and the

lifting arm moves downwards if under load.

The manual emergency lowering function on the

actuator should only be used when the electrical

emergency lowering does not work.

Emergency

stop

Electrical

emergency

lowering

Manual

emergency

lowering

10

Molift Smart 150 / www.etac.com

Transport and operating conditions

Transport and storage

For long time storage it is recommended that the

emergency stop button is activated (pushed in).

The lifter can be stored and transported under

temperatures between -25 - 70 °C.

Operating

The lifter is designed for use at standard room

temperatures (+5 to +40°C).

Air pressure: 70 - 106 kPa

Relative humidity: 15 - 93 %

Following storage or transport at other tempera-

tures leave the lifter in a room with a suitable

temperature until it reaches a safe operating

temperature.

Medical electrical equipment

requires special precautions regard-

ing electromagnetic compatibility

(EMC). Portable or mobile radio

communication equipment may

affect the medical electrical equip-

ment, and should be kept minimum

25 cm (10 inches) from the lifters

electronics.

Battery

Molift Mover 300 has a 26.4 V 2.6Ah NiMH bat-

tery. The battery has a life expectancy of approx.

500 charging cycles.

Recharge battery upon receipt, and

then every six months, to avoid

battery failure.

Used batteries must be disposed

of as special waste according to

local rules and regulations. Do not

dispose in general waste

x2

Batteries must be fully charged

and drained completely a couple of

times before it achieves full capac-

ity. Also follow this procedure if

the lifter has not been in use for a

long period (4 weeks or more)

Battery and service indicator

The lifter has two indicator lights on the battery

holder.

Service indicator

Battery indicator

The electrical system has a power save function

which will turn off the electrical system after ten

minutes without activity. All lights will turn off.

The system is activated when pushing one of the

operating buttons

Battery indicator (LED)

The battery indicator light will illuminate and

make a sound when battery level is low and the

lifter requires charging. When this occurs the lifter

will have sufﬁcient power available for one full lift-

ing cycle with max load. When battery is critically

low it is only possible to lower the lifting arm.

Service indicator

The lifters electronics record the loads lifted and

number of lifts. After a certain period of operation

a signal is given to indicate that service is required.

Service indicator Mode

No light Power saving (Stand by)

Green Ready for use

Yellow Order service

Red Perform service

Red + sound Perform service

immediately

Service scope

Service involves replacing the lifting motor and

inspection/replacement of worn parts. This must

be carried out by authorized personnel.

Service is needed when the service indicator is red

(calculated 10.000 lifts in SWL).

Electronics

11

Molift Smart 150 / www.etac.com

ENNO DEFR ITES FI SVNLDA

Charging

Battery Charger

The battery charger can be used as a tabletop

charger or mounted to a vertical wall surface

close to a power outlet, minimum 120 cm above

the ﬂoor. The charger has to be used outside the

patient environment. The Charger must be placed

or installed in a way that makes it easy to discon-

nect mains cable plug. Take care not to damage

the cable. The charger can be connected to the

power outlet at all times.

Battery charger 12-24V

Art. no. 1340100

Charger indicator (LED)

Description of charger indicator (LED):

LED Mode

Yellow Ready for use, no bat-

tery connected

Yellow Initialization

Red Fast Charge

Green/Yellow Top-off charge

Green Trickle charge

Red/Green Error

Battery

indicator

(LED)

Battery

charger

Mains cable

(disconnecting

device)

12

Molift Smart 150 / www.etac.com

Transfer

Plan the lifting operation in advance to ensure that

it is as safe and smooth as possible. Remember

to work ergonomically. Assess the risks and take

notes. The assistant is responsible for the safety of

the user.

Molift Mover 300 can be used with 4-point sling

bar for different types of transfers; sitting, recum-

bent or ambulating.

Using slings

It is important that the sling has been tested with

the individual user and for the intended lifting

situation.

Read user manual for the sling

prior to use.

Do not to use damaged or badly

worn slings.

Slings made by other manufacturers

We recommend only using Molift slings. Etac shall

not be liable for faults or accidents that can occur

when using slings made by other manufacturers.

Lifting and lowering

When moving the user, stand to the side of the

person you are lifting. Make sure that arms and

legs do not obstruct the seat, bed, etc. Keep eye

contact with the user to help them feel safe.

The sling bar must always be positioned across

the user, to prevent the user from unintentionally

sliding out of the sling.

The sling bars hook design prevents sling to be

inadvertently detached when mounted correct.

1. Check that the sling is correctly ﬁtted around

the user and that the strap loops are correctly

ﬁtted to the sling bar hooks.

2. Stretch the sling straps without lifting the

user. Ensure that all four loops of the sling are

securely fastened to avoid the user slipping or

falling.

3. Lift user, and perform transfer.

Supporting arms (optional)

The lifter can be used for gait training with sup-

porting arms.

Lifter can be delivered with supporting arms, or

complete lifting column with supporting arms can

be delivered as an accessory to swap with original

lifting column.

Column with supporting arms

Art. no. 1511002

13

Molift Smart 150 / www.etac.com

ENNO DEFR ITES FI SVNLDA

Transfer

Try to position the user as low as possible

(preferably resting the feet on the chassis) when

transferring the lifter with a suspended user. In this

way the centre of gravity will be low and reduce

the risk of instability.

Never lift the user higher than

necessary to carry out a lift.

Remember that wheels on a mobile

lift must NOT be locked.

Never leave a user unattended in a

lifting situation.

Be careful during movement, the suspended user

may swing during turns, stops and starts. Be

careful when manoeuvring close to furniture to

prevent the suspended user from colliding with

these objects.

The lifter shall not be used to lift or

move users on sloping surfaces

Avoid deep pile carpets, high thresholds, uneven

surfaces or other obstacles that may block the cas-

tors. The lifter may become unstable if forced over

such obstacles increasing the risk of tipping over.

Lowering into sitting

When transferring the user into sitting, the follow-

ing techniques can be used when lowering the

user as far back into the seat as possible:

A Position the user with the help of the push

handle

B Push gently on the users knees

C Tilt the seat backwards

User must be facing lifter when

lifting or lowering from or into a

chair.

14

Molift Smart 150 / www.etac.com

Accessories

Recommended optional equipment and acces-

sories for Molift Mover 300.

Sling bars and sling bars with scale

Molift Mover 300 can be used with a 4 point sling

bar. Sling bars are available with or without Molift

Scale. Molift Scale is approved Class III. The scale

can also calculate BMI (Body Mass Index).

4-point sling bar

4-point Medium, aluminum, width = 450 mm,

Art. no.: 1530101

Art. no.: 1430110 (Incl. Molift Scale)

4-point Large, aluminum, width = 550 mm,

Art. no.: 1530102

Art. no.: 1530111 (Incl. Molift Scale)

4-point Extra large, aluminum, width = 650 mm,

Art. no.: 1530103

Castor with directional lock

Art. no. 1320140

This castor has no brake, therefore we recommend

to change only one of the castors.

Stretcher

The Molift stretcher can be used in combination

with all Molift 4-point sling bars on Molift Mover

300.

Scoop stretcher MRI compatible (SWL 300 kg)

Art. no.: 2150108

Slings

Etac supplies a wide selection of slings for

different types of transfers. The Molift RgoSling

sling series is developed to be combined with

a 4-point sling bar, (also works with a 2-point

sling bar). The Etac EvoSling series is developed

to be combined with a 2-point sling bar. See the

combination list in the slings user manual for the

correct sling and sling bar combination.

The sling series is available in sizes XXS – XXL, in

polyester and polyester mesh.

RgoSlings:

RgoSling Mediumback Padded (XS-XXL)

RgoSling Highback Padded (XS-XXL)

RgoSling Mediumback Net (XXS-XXL)

RgoSling Highback Net (XXS-XXL)

RgoSling Toilet Lowback (XXS-XXL)

RgoSling Toilet Highback (XXS-XXL)

RgoSling Ampu Mediumback (XXS-XXL)

RgoSling Ampu Highback (XXS-XXL)

RgoSling Ambulating Vest (XXS-XL)

RgoSling Comfort Highback (S-L)

Accessories:

RgoSling Extension Loops

RgoSling Ambulating Vest Groin strap (XXS-XL)

15

Molift Smart 150 / www.etac.com

ENNO DEFR ITES FI SVNLDA

Maintenance

Cleaning and disinfection

Clean on a regular basis. Clean surfaces with

a damp cloth using an appropriate pH-neutral

detergent. Do not use solvents or strong liquids,

this may damage surfaces on the lifter. For

disinfection when needed; use isopropyl alcohol.

Avoid abrasive cleaning products. Remove hair

and pile from the castors and verify that the

castors rotates freely. Clean contact and hand

control with isopropyl alcohol to remove grease

and dirt. Check emergency stop and emergency

lowering after cleaning. The lift should not be

exposed to running water.

Make sure not to damage or

remove labels when cleaning.

Reconditioning

Follow cleaning and assembly procedure, complete

periodic inspection and use checklist after assem-

bly to recondition the lifter.

Recycling

Refer to “Recycling instructions” for how to

properly dispose of product. This can be found on

www.etac.com.

Spare Parts

A list of spare parts is available on request.

Periodic inspection

Periodic inspection scope

Periodic inspection is a visual examination (particu-

larly of the lifter’s load bearing structure and lifting

mechanism with attachments, brakes, controls,

safety devices and person-support devices) accord-

ing to Periodic Inspection Report for Molift Mover

300. This can be found on www.etac.com.

If there is any problems with the

lifter that could jeopardize some-

ones safety, the lifter shall imme-

diately be taken out of service and

marked “out of order”. Do not use

the lifter untill it is repaired.

Periodic Inspection shall be performed annually or

more frequently if required by local requirements.

The inspection must be performed by service

personnel authorized by Etac.

Contact Etac at molift@etac.com for training and

authorization or recommendation of an approved

service partner.

When performing a periodic inspection, the

inspector shall ﬁll out the inspection report for

Molift Mover 300. The reports should be retained

by the person(s) responsible for servicing the lifter.

If the inspection reveals defects and damages, the

owner shall be notiﬁed.

When periodic inspection is completed the

inspector shall mark the lifter with a sticker on

the control label showing the date when periodic

inspection is performed and a label (with 6-digit

ID from Etac or distributor) showing who has

performed the periodic control. The control label

can be found on the right side of the battery

holder, and this will then indicate the date when

next Inspection is due.

Mark label

with month

and year of

inspection

16

Molift Smart 150 / www.etac.com

Troubleshooting

Symptom Possible cause / action

The lifting column is wobbly The lifting column is not correctly positioned

in the chassis or the locking handle is not fully

locked.

Assemble column and chassis properly.

The lifter moves unevenly on a plane surface The castors move unevenly because of pile and

dust.

Clean the castors. Remove hair and dirt.

The lifting arm or adjustable legs moves

uncontrolled.

Short circuit between hand control and lifter.

Clean hand control plug surfaced with alcohol to

remove grease.

Defective hand control.

Replace hand control.

The control electronics has failed.

Contact local representative for service.

The lifter does not respond to hand control action

/ The lifting arm or legs does not move.

Emergency stop button is activated.

Turn button clockwise to reset emergency stop.

Battery is empty.

Change or charge battery.

The lifters electronics is overheated.

Wait for it to cool down.

The lifter is overloaded.

Make sure the load does not exceed SWL.

Hand control is not plugged in properly.

Plug in Hand control properly. Hand control, plug

or cord can be broken and should be replaced.

Contact between chassis and column has no

connection. Column is not correctly mounted in

chassis.

Assemble column and chassis properly.

Defective control electronics.

Contact local representative for service.

Battery does not charge Faulty battery.

Check indicators on charger when charging.

Try another battery.

Faulty battery charger.

Check indicators on charger when charging. See

chapter “Charging”.

Try another charger.

17

Molift Smart 150 / www.etac.com

ENNO DEFR ITES FI SVNLDA

Molift Mover 300

DE - Bedienungsanleitung

BM06102 Rev. E 2021-02-16

Gebrauchsanweisung - Deutsch

Wichtiger Hinweis

Diese Bedienungsanleitung enthält wichtige

Hinweise und Informationen für den sicheren

Gebrauch des Lifters und des Zubehörs.

In dieser Bedienungsanleitung bezeichnet

„Benutzer“ diejenige Person, die gehoben wird.

Der „Helfer“ ist diejenige Person, die den Lifter

bedient.

Warnung!

Dieses Symbol weist auf wichtige

Sicherheitshinweise hin. Befolgen

Sie diese Anweisungen bitte genau.

Lesen Sie vor dem Gebrauch die

Bedienungsanleitung!

Es ist sehr wichtig, dass Sie

vor Inbetriebnahme des

Geräts mit dem Inhalt der

Bedienungsanleitung genau ver-

traut sind.

Besuchen Sie www.etac.com und vergewissern

Sie sich, dass Sie über die neueste Version der

Bedienungsanleitung verfügen.

Deutsche Bedienungsanleitung

20

Molift Smart 150 / www.etac.com

La page charge ...

Molift Mover 300 Manuel utilisateur

Molift Mover 300 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents