Wacker Neuson LTN6LE Manuel utilisateur

Operator’s Manual

Notice d'emploi

Light Tower

Tour d’éclairage

LTN6L

(60 Hz)

Type

Document

Date

Version

Language

LTN6L (60 Hz)

5000187507

0121

08

EN-FR

5000187507

Copyright

notice

on America Corporation

All rights, including copying and distribution rights, are reserved.

This publication may be photocopied by the original purchaser of the machine. Any other

type of reproduction is prohibited without express written permission from Wacker

Neuson America Corporation.

Any type of reproduction or distribution not authorized by Wacker Neuson America

Corporation represents an infringement of valid copyrights. Violators will be prosecuted.

Trademarks

All trademarks referenced in this manual are the property of their respective owners.

Manufacturer

Wacker Neuson America Corporation

N92W15000 Anthony Avenue

Menomonee Falls, WI 53051 U.S.A.

Tel: (262) 255-0500 · Fax: (262) 255-0550 · Tel: (800) 770-0957

www.wackerneuson.com

Original

instructions

This Operator’s Manual presents the original instructions. The original language of this

Operator’s Manual is American English.

LTN 6L Foreword

wc_tx001571gb.fm 3

Foreword

SAVE THESE INSTRUCTIONS—This manual contains important instructions for

the machine models below. These instructions have been written expressly by

Wacker Neuson America Corporation and must be followed during installation,

operation, and maintenance of the machines.

Machines

covered in

this manual

Machine

documentation

Expectations

for

information in

this manual

 From this point forward in this documentation, Wacker Neuson America

Corporation will be referred to as Wacker Neuson.

 Keep a copy of the Operator’s Manual with the machine at all times.

 Use the separate Parts Book supplied with the machine to order replacement

parts.

 Refer to the separate Repair Manual for detailed instructions on serv

icing and

repairing the machine.

 If you are missing any of these documents, please contact Wacker Neuson to

order a replacement or visit www.wackerneuson.com.

 When ordering parts or requesting service information, be prepared to provide

the machine model number, item number, revision number, and serial number.

 This manual provides information and procedures to safely operate and

maintain the above Wacker Neuson model(s). For your own safety and to

reduce the risk of injury, carefully read, understand, and observe all instructions

described in this manual.

 Wacker Neuson expressly reserves the right to make technical modifications,

even without notice, which improve the performance or safety standards of its

mac

hines.

 The information contained in this manual is based on machines manufactured

up until the time of publication. Wacker Neuson reserves the right to change

any portion of this information without notice.

CALIFORNIA

Proposition

65 Warning

Engine exhaust, some of its constituents, and certain vehicle components, contain

or emit chemicals known to the State of California to cause cancer and birth

defects or other reproductive harm.

Laws

pertaining to

spark

arresters

NOTICE: State Health Safety Codes and Public Resources Codes specify that in

certain locations spark arresters be used on internal combustion engines that use

hydrocarbon fuels. A spark arrester is a device designed to prevent accidental dis-

charge of sparks or flames from the engine exhaust. Spark arresters are qualified

and rated by the United States Forest Service for this purpose. In order to comply

with local laws regarding spark arresters, consult the engine distributor or the local

Health and Safety Administrator.

Machine Item Number

LTN 6L 0620117, 0620727, 0620550, 0620553, 0620561,

0620554, 0620297

Foreword LTN 6L

4 wc_tx001571gb.fm

Manufacturer’s

approval

This manual contains references to approved parts, attachments, and modifica-

tions. The following definitions apply:

 Approved parts or attachments are those either manufactured or provided by

W

acker Neuso

n.

 Approved modifications are those performed by an authorized Wacker

Neuson service center according to written instructions published by Wacker

Neu

son.

 Unapproved parts, attachments, and modifications are those that do not

meet

the approved criteria.

Unapproved parts, attachments, or modifications may have the following conse-

quences:

 Serious injury hazards to the operator and persons in the work area

 Permanent damage to the machine which will not be covered under warranty

Contact your Wacker Neuson dealer immediately if you have questions abo

ut

approved or

unapproved parts, attachments, or modifications.

wc_bo5000187483_07TOC.fm 5

Table of ContentsLTN 6L

Foreword 3

1

Safety Information 9

1.1 Signal Words Used in this Manual ....................................................... 9

1.2 Machine Description and Intended Use ............................................. 10

1.3 Safety Guidelines for Operating the Machine ..................................... 11

1.4 Operator Safety while Using Internal Combustion Engines ............... 13

1.5 Lamp Safety ....................................................................................... 14

1.6 Service Safety .................................................................................... 14

2 Labels 16

2.1 Label Locations .................................................................................. 16

2.2 Label Meanings .................................................................................. 18

3 Lifting and Transporting 31

4 Operation 32

4.1 Preparing the Machine for First Use ................................................... 32

4.2 Locating the Trailer ............................................................................. 33

4.3 Leveling Trailer ................................................................................... 34

4.4 Ground Connection ............................................................................ 34

4.5 Refueling the Machine ........................................................................ 35

4.6 Adjusting Lights .................................................................................. 36

4.7 Control Panels (Manual Winch System) ............................................. 37

4.8 Control Panels (120/240, Manual Winch System) .............................. 38

4.9 Control Panels (Power Winch System) .............................................. 39

4.10 Starting ............................................................................................... 40

4.11 Stopping ............................................................................................. 40

4.12 Operating Lights ................................................................................. 41

4.13 Raising Tower (Manual Winch System) ............................................. 42

4.14 Lowering Tower (Manual Winch System) ........................................... 45

4.15 Raising Tower (Power Winch System) ............................................... 47

4.16 Lowering Tower (Power Winch System) ............................................ 49

6 wc_bo5000187483_07TOC.fm

Table of Contents LTN 6L

4.17 Emergency Crank Handle (Power Winch System) ..............................50

4.18 Automatic Shutdown ...........................................................................50

4.19 Emergency Shutdown Procedure ........................................................51

4.20 Derating ...............................................................................................51

4.21 Receptacle ..........................................................................................52

5 Factory Installed Options 53

5.1 Engine Block Heater Option ................................................................53

5.2 Battery Blanket ....................................................................................53

5.3 Oil Pan Heater .....................................................................................54

6 Maintenance 55

6.1 Periodic Maintenance Schedule ..........................................................55

6.2 IInstalling / Removing Light Fixtures ...................................................56

6.3 Replacing / Removing Lamps .............................................................57

6.4 Daily Inspection ...................................................................................58

6.5 Air Cleaner ..........................................................................................58

6.6 Engine Oil ............................................................................................59

6.7 Long-Term Storage .............................................................................60

6.8 Troubleshooting ...................................................................................62

7 Technical Data 63

7.1 Engine .................................................................................................63

7.2 Generator ............................................................................................64

7.3 Machine ...............................................................................................64

8 Schematics 66

8.1 Electrical Schematic ............................................................................66

8.2 Trailer Wiring .......................................................................................70

8.3 Engine Wiring ......................................................................................71

8.4 Control Panel Wiring ...........................................................................72

8.5 Power Winch Schematic .....................................................................73

wc_bo5000187483_07TOC.fm 7

Table of ContentsLTN 6L

9 Appendix I—Assembly Instructions 74

9.1 Introduction ......................................................................................... 74

10 Appendix II—Assembly Safety 76

10.1 Signal Words Used in this Manual ..................................................... 76

10.2 Lifting Safety ....................................................................................... 77

10.3 Pre-Assembly Checklist ..................................................................... 77

11 Appendix III—Standard Pallet Assembly 78

11.1 Installing the Outriggers and Outrigger Jacks .................................... 79

11.2 Installing the Rear Jack ...................................................................... 80

11.3 Installing the Tongue Assembly ......................................................... 81

11.4 Installing the Upper Light Fixtures ...................................................... 83

11.5 Conclusion .......................................................................................... 83

12 Appendix IV—CE Pallet Assembly 84

12.1 Installing the Side Jacks ..................................................................... 85

12.2 Installing the Rear Jack ...................................................................... 86

12.3 Conclusion .......................................................................................... 87

13 Appendix V—Standard Racked Assembly 88

13.1 Installing the Axle ............................................................................... 90

13.2 Installing the Fenders ......................................................................... 91

13.3 Installing the Wheels .......................................................................... 91

13.4 Installing the Outriggers and Outrigger Jacks .................................... 92

13.5 Installing the Rear Jack ...................................................................... 93

13.6 Installing the Tongue Assembly ......................................................... 94

13.7 Installing the Tower Lock Bracket ...................................................... 96

13.8 Installing the Tower Cradle ................................................................. 97

13.9 Installing the Tower ............................................................................ 98

13.10 Installing the Tower Pivot Cable ......................................................... 99

8 wc_bo5000187483_07TOC.fm

Table of Contents LTN 6L

13.11 Installing the Lights ............................................................................100

13.12 Connecting the Wiring at the Junction Box .......................................101

13.13 Routing the Coil Cord ........................................................................103

13.14 Wiring the Ballasts and Terminal Strips ............................................104

13.15 Conclusion .........................................................................................106

LTN 6L Safety Information

wc_si000227gb.fm 9

1 Safety Information

1.1 Signal Words Used in this Manual

This manual contains DANGER, WARNING, CAUTION, NOTICE, and

NOTE signal words which must be followed to reduce the possibility

of personal injury, damage to the equipment, or improper service.

NOTICE: Used without the safety alert symbol, NOTICE indicates a

situation which, if not avoided, could result in property damage.

Note: A Note contains additional information important to a procedure.

This is the safety alert symbol. It is used to alert you to potential personal hazards.

f Obey all safety messages that follow this symbol.

DANGER

DANGER indicates a hazardous situation which, if not avoided, will result in death

or serious injury.

f To avoid death or serious injury from this type of hazard, obey all safety mes-

sages that follow this signal word.

WARNING

WARNING indicates a hazardous situation which, if not avoided, could result in

death or serious injury.

f To avoid possible death or serious injury from this type of hazard, obey all safety

messages that follow this signal word.

CAUTION

CAUTION indicates a hazardous situation which, if not avoided, could result in

minor or moderate injury.

f To avoid possible minor or moderate injury from this type of hazard, obey all

safety messages that follow this signal word.

Safety Information LTN 6L

10 wc_si000227gb.fm

1.2 Machine Description and Intended Use

This machine is a mobile, trailer-mounted light tower. The Wacker

Neuson Light Tower consists of a trailer with a cabinet containing a

diesel engine, a fuel tank, a control panel, and an electric alternator. A

telescoping tower with four metal halide lights is mounted to the top of

the cabinet. Dual winches tilt, raise, and lower the telescoping tower.

As the engine runs, the generator converts mechanical energy into

electric power. The metal halide lights run off this power.

Receptacle(s) are also present to power auxiliary loads. The operator

uses the control panel to operate and monitor the machine.

This machine is intended for the illumination of outdoor areas. This

machine is also intended for the purpose of supplying electrical power

to connected loads. Refer to the product specifications for the output

voltage and frequency of this Light Tower, and for the maximum

output power limit of this Light Tower.

This machine has been designed and built strictly for the intended use

described above. Using the machine for any other purpose could

permanently damage the machine or seriously injure the operator or

other persons in the area. Machine damage caused by misuse is not

covered under warranty.

• The following are some examples of misuse:

• Connecting a load that has voltage and frequency requirements

that are incompatible with the machine output

• Overloading the machine with a device that draws excessive

power during either continuous running or start-up

• Operating the machine in a manner that is inconsistent with all

federal, state and local codes and regulations

• Using the machine as a ladder, support, or work surface

• Using the machine to carry or transport passengers or equipment

• Using the machine to tow other machines (unless factory

equipped)

• Using the machine as a hoist or hanging items from the tower

• Operating the machine outside of factory specifications

• Operating the machine in a manner inconsistent with all warnings

found on the machine and in the Operator’s Manual

This machine has been designed and built in accordance with the

latest global safety standards. It has been carefully engineered to

eliminate hazards as far as practicable and to increase operator

safety through protective guards and labeling. However, some risks

may remain even after protective measures have been taken. They

LTN 6L Safety Information

wc_si000227gb.fm 11

are called residual risks. On this machine, they may include exposure

to:

• Heat, noise, exhaust, and carbon monoxide from the engine

• Heat from the lights

• Ultraviolet radiation from the lights

• Fire hazards from improper refueling techniques

• Fuel and its fumes

• Electric shock and arc flash

• Personal injury from improper lifting the trailer tongue

• Glare from lights (lights may blind drivers of nearby motor

vehicles if the lights are incorrectly positioned)

• Typical hazards related to towing a trailer on roads and highways

To protect yourself and others, make sure you thoroughly read and

understand the safety information presented in this manual before

operating the machine.

1.3 Safety Guidelines for Operating the Machine

Operator qualifications

Only trained personnel are permitted to start, operate, and shut down

the machine. They also must meet the following qualifications:

• have received instruction on how to properly use the machine

• are familiar with required safety devices

The machine must not be accessed or operated by:

•children

• people impaired by alcohol or drugs

Personal Protective Equipment (PPE)

Wear the following Personal Protective Equipment (PPE) while

operating this machine:

• Close-fitting work clothes that do not hinder movement

• Safety glasses with side shields

• Hearing protection

• Safety-toed footwear

1.3.1 Do not remove, defeat, deface, or render inoperable any of the safety

devices, warnings, or labels on this equipment. If any safety devices,

warnings, or labels have been removed, defeated, defaced, or

rendered inoperable, do NOT use this equipment!

1.3.2 The area immediately surrounding the Light Tower should be clean,

neat, and free of debris.

Safety Information LTN 6L

12 wc_si000227gb.fm

1.3.3 Be sure the machine is on a firm, level surface and will not tip, roll,

slide, or fall while operating.

1.3.4 NEVER start a machine in need of repair.

1.3.5 Lower the tower when not in use, or if high winds or electrical storms

are expected in the area.

1.3.6 Always make certain the machine is well-grounded and securely

fastened to a good earthen ground per national and local regulations.

1.3.7 The tower extends up to 9 m (30 ft.). Make sure the area above the

trailer is open and clear of overhead wires and obstructions.

1.3.8 The lamps become extremely hot in use! Allow the lamp and fixture to

cool 10–15 minutes before handling.

1.3.9 Keep the area behind the trailer clear of people while raising and

lowering the tower! Never raise, lower or turn the tower while unit is

operating!

1.3.10 The trailer must be leveled and the outriggers extended before raising

the tower. The outriggers must remain extended while the tower is up.

1.3.11 If for any reason any part of the tower hangs up or the winch cable

develops slack while raising or lowering the tower, STOP immediately!

Contact an authorized Wacker Neuson service representative.

1.3.12 NEVER remove the tower locking pin while the tower is up!

1.3.13 NEVER use the machine if the insulation on the electrical cord is cut or

worn through.

1.3.14 NEVER operate the lights without the protective lens cover in place or

with a lens cover that is cracked or damaged!

1.3.15 NEVER adjust the tower while the unit is operating.

Do not move the Light Tower while it is operating.

1.3.16 NEVER raise the tower or operate the machine in high winds.

1.3.17 NEVER connect machine to other power sources, such as supply

mains of power companies.

1.3.18 ALWAYS replace or repair electrical components with components

that are identical in rating and performance as the original component.

LTN 6L Safety Information

wc_si000227gb.fm 13

1.4 Operator Safety while Using Internal Combustion Engines

Operating safety

When running the engine:

• Keep the area around exhaust pipe free of flammable materials.

• Check the fuel lines and the fuel tank for leaks and cracks before

starting the engine. Do not run the machine if fuel leaks are present

or the fuel lines are loose.

When running the engine:

• Do not smoke while operating the machine.

• Do not run the engine near sparks or open flames.

• Do not touch the engine or muffler while the engine is running or

immediately after it has been turned off.

• Do not operate a machine when its fuel cap is loose or missing.

• Do not start the engine if fuel has spilled or a fuel odor is present.

Move the machine away from the spill and wipe the machine dry

before starting.

Refueling safety

When refueling the engine:

• Clean up any spilled fuel immediately.

• Refill the fuel tank in a well-ventilated area.

• Replace the fuel tank cap after refueling.

• Do not smoke.

• Do not refuel a hot or running engine.

• Do not refuel the engine near sparks or open flames.

WARNING

Internal combustion engines present special hazards during operation and fueling. Failure to

follow the warnings and safety standards could result in severe injury or death.

f Read and follow the warning instructions in the engine owner’s manual and the

safety guidelines below.

DANGER

Exhaust gas from the engine contains carbon monoxide, a deadly poison. Expo-

sure to carbon monoxide can kill you in minutes.

f NEVER operate the machine inside an enclosed area, such as a tunnel, unless

adequate ventilation is provided through such items as exhaust fans or hoses.

Safety Information LTN 6L

14 wc_si000227gb.fm

1.5 Lamp Safety

Description

The lamps provided with your Light Tower are electric discharge

lamps. They are designed for use with metal halide ballasts only, and

require time to reach full brightness on initial startup and after a power

interruption. These lamps comply with FDA regulation performance

standards 21 CFR 1040-30.

Operating safety

• Do not operate the lamps where people will remain for more than

a few minutes unless adequate shielding or other safety

precautions are used.

• Replace damaged lamps according to the instructions in section

Removing / Replacing Lamps.

• Lamps that automatically extinguish when the outer envelope is

broken or punctured are commercially available.

1.6 Service Safety

HIGH VOLTAGE! This unit uses high voltage circuits capable of

causing serious injury or death. Only a qualified electrician should

troubleshoot or repair electrical problems occurring with this

equipment.

Personal Protective Equipment (PPE)

Wear the following Personal Protective Equipment (PPE) while

servicing or maintaining this machine:

• Close-fitting work clothes that do not hinder movement

• Safety glasses with side shields

• Hearing protection

• Safety-toed footwear

In addition, before servicing or maintaining the machine:

• Tie back long hair.

• Remove all jewelry (including rings).

WARNING

Personal injury hazard. Lamps can cause serious skin burns and eye inflammation

from shortwave ultraviolet radiation if outer envelope of the lamp is broken or punc-

tured.

f Do not operate the Light Tower if a lamp is damaged.

WARNING

LTN 6L Safety Information

wc_si000227gb.fm 15

1.6.1 ALWAYS replace the safety devices and guards after repairs and

maintenance.

1.6.2 Before servicing the Light Tower, make sure the engine start switch is

turned to the OFF position, the circuit breakers are open (off), and the

negative terminal on battery is disconnected. NEVER perform even

routine service (oil/filter changes, cleaning, etc.) unless all electrical

components are shut down.

1.6.3 Do not allow water to accumulate around the base of the machine. If

water is present, move the machine and allow the machine to dry

before servicing.

1.6.4 Do not service the machine if your clothing or skin is wet.

1.6.5 ALWAYS keep hands, feet, and loose clothing away from the moving

parts on the generator and engine.

1.6.6 Keep the machine clean and labels legible. Replace all missing and

hard-to-read labels. Labels provide important operating instructions

and warn of dangers and hazards.

1.6.7 When replacement parts are required for this machine, use only

Wacker Neuson replacement parts or those parts equivalent to the

original in all types of specifications, such as physical dimensions,

type, strength, and material.

1.6.8 ALWAYS make sure slings, chains, hooks, ramps, jacks, and other

types of lifting devices are attached securely and have enough weight-

bearing capacity to lift or hold the machine safely. Always remain

aware of the location of other people in the area when lifting the

machine.

1.6.9 ALWAYS turn off the light circuit breakers and shut down the engine

before disconnecting the light fixtures or changing the lamps.

Labels LTN 6L

16 wc_si000381gb.fm

2 Labels

2.1 Label Locations

wc_gr007036

B

H

D

I

G

PO

X

J

K

Z

QS

RT

CC

BB

MM

BB

AA

EE

C

A

E

LL

V

LTN 6L Labels

wc_si000381gb.fm 17

wc_gr007037

RS

U

V

L

H

F

B

N

J

M

D

Y

FF

AA

LL

AA

DD

BB

GG

EE

CC

BB

HH

JJ

Labels LTN 6L

18 wc_si000381gb.fm

2.2 Label Meanings

Wacker Neuson machines use international pictorial labels where

needed. These labels are described below.

A

WARNING

Automatic locking pin.

A non-secured, falling tower can cause serious

injury or death if a person is hit. To secure tower,

verify automatic locking pin has been engaged.

B

WARNING!

Avoid crushing area.

C

DANGER!

Contact with overhead electrical power lines will

cause serious injury or death. Do not position

Light Tower under electrical power lines.

WARNING!

Completely lower tower BEFORE tilting tower.

Tilting an extended tower can cause serious

injury or death.

LTN 6L Labels

wc_si000381gb.fm 19

D

NOTICE

Lifting point.

E

WARNING!

Secure tower in transport lock before lifting or

towing. A loose swinging tower could cause per-

sonal injury or machine damage.

F

DANGER!

No sparks, flames, or burning objects near

machine. Stop the engine before adding fuel. Use

only diesel fuel.

G

DANGER!

Asphyxiation hazard.

 Engines emit carbon monoxide.

 Do not run the machine indoors or in an

enclosed area unless adequate ventilation,

through such items as exhaust fans or hoses,

is provided.

 Read the Operator’s Manual. No sparks,

flames, or burning objects near the machine.

Stop the engine before refueling.

Labels LTN 6L

20 wc_si000381gb.fm

H

WARNING!

Electric shock and arc flash can cause serious

injury or death. Electrical storage device within.

Contact a qualified electrician for service or to

open electrical box.

I

WARNING!

Read and understand the supplied Operator’s

Manual before operating the machine. Failure to

do so increases the risk of injury to yourself and

others.

J

WARNING!

Stand clear of front and rear of machine when

tower is being tilted up or down.

K

WARNING!

Hot surface

L

WARNING!

Hot surface

La page est en cours de chargement...

Wacker Neuson LTN6LE Manuel utilisateur

Ce manuel convient également à

Wacker Neuson LTN6LE Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents