DeWalt DCS7485B Manuel utilisateur

Marque: DeWalt

Modèle: DCS7485B

Taper: Manuel utilisateur

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, contáctenos.

1-800-4-DeWALT

Instruction Manual

Guide D’utilisation

Manual de instrucciones

DCS7485

Cordless Table Saw

Scie de table sans fil

Sierra de banco inalámbrica

final page size: 8.5 x 11 in.

English (original instructions) 1

Français (traduction de la notice d’instructions originale) 14

Español (traducido de las instrucciones originales) 28

English (original instructions)

Definitions: Safety Alert Symbols and Words

This instruction manual uses the following safety alert symbols and words to alert you to hazardous situations and your risk

of personal injury or propertydamage.



DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or seriousinjury.



WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or seriousinjury.



CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderateinjury.



(Used without word) Indicates a safety relatedmessage.

NOTICE: Indicates a practice not related to personal injury which, if not avoided, may result in propertydamage.



WARNING! Read all safety warnings and

allinstructions. Failure to follow the warnings

and instructions may result in electric shock, fire

and/or seriousinjury.

WARNING: To reduce the risk of injury, read the

instructionmanual.

Table

Blade

Rip scale indicator

Fine adjust knob

Rail lock lever

Blade height adjustment wheel

Bevel lock lever

ON/OFF assembly

Mounting holes

Miter gauge

Blade guard assembly

Battery

Battery release button

Anti-kickback assembly

Dust collection port

Guard dust collection port

Throat plate

Rip fence

Rip fence latch

Narrow ripping fence/support extension

Blade wrenches (stored position)

Push stick (stored position)

Riving knife (non thru sawing) (Fig.G)

Carry handle

Miter gauge track

Fig. A

SAVE ALL WARNINGS AND INSTRUCTIONS FOR

FUTURE REFERENCE

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY

DeWALT

TOOL, CALL US TOLL

FREE AT: 1–800–4-

DeWALT

(1–800–433–9258).



WARNING: To reduce the risk of injury, read the instructionmanual.

General Safety Rules



WARNING: Read all instructions before operating product. Failure to follow all instructions

listed below may result in electric shock, fire and/or seriousinjury.



WARNING: FOLLOW ALL WIRING CODES and recommended electrical connections to

prevent shock orelectrocution.

Important Safety Instructions

• TO REDUCE THE RISK OF KICKBACK AND OTHER INJURIES, use all components of the

guarding system (blade guard assembly, riving knife and anti-kickback) for every operation for

which they can be used including all thru-cutting.

• REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and

adjusting wrenches are removed from spindle before turning tool on. Tools, scrap pieces, and

other debris can be thrown at high speed, causinginjury.

• KEEP WORK AREA CLEAN. Cluttered areas and benches inviteaccidents.

• DO NOT USE THE MACHINE IN A DANGEROUS ENVIRONMENT. The use of power tools in

damp or wet locations or in rain can cause shock or electrocution. Keep your work area well-lit to

avoid tripping or placing arms, hands, and fingers indanger.

• KEEP CHILDREN AWAY. All visitors should be kept at a safe distance from work area. Your shop

is a potentially dangerousenvironment.

• MAKE WORKSHOP CHILDPROOF with padlocks, master switches, or by removing starter keys

and the battery. The unauthorized start-up of a machine by a child or visitor may result ininjury.

• DO NOT FORCE TOOL. It will do the job better and be safer at the rate for which it wasdesigned.

• USE THE RIGHT TOOL. Don’t force tool or attachment to do a job for which it was not designed.

Using the incorrect tool or attachment may result in personalinjury.

• DO NOT OVERREACH. Keep proper footing and balance at all times. Loss of balance may cause

personal injury. Do not attempt to retrieve materials near the blade on the saw table while the

blade isspinning.

• MAINTAIN TOOLS WITH CARE. Keep blades sharp and clean for best and safest performance.

Follow instructions for lubricating and changing accessories. Poorly maintained blades and

machines can further damage the blade or machine and/or causeinjury.

• WEAR PROPER APPAREL. Do not wear loose clothing, gloves, neckties, rings, bracelets, or

other jewelry which may get caught in moving parts. Nonslip footwear is recommended. Wear

protective hair covering to contain longhair.

• ALWAYS USE SAFETY GLASSES. Also use face or dust mask if cutting operation is dusty.

Everyday eyeglasses only have impact resistant lenses, they are NOT safetyglasses.

• SECURE WORK. Use clamps to hold work when practical (such as when using a zero clearance

insert/throat plate). It's safer than using your hand and it frees both hands to operatetool.

• TURN UNIT OFF AND REMOVE THE BATTERY PACK before installing or removing accessories,

before adjusting or changing set-ups, when making repairs or changinglocations.

• Do not install or remove the battery pack with wethands.

• ENSURE THE SWITCH IS IN THE OFF POSITION BEFORE INSERTING BATTERY PACK.

Inserting the battery pack into power tools invitesaccidents.

• USE RECOMMENDED ACCESSORIES. Use only accessories that are recommended by the

manufacturer for your model. Accessories that may be suitable for one tool may be hazardous

when used on another tool. Consult the instruction manual for recommended accessories. The

use of improper accessories may cause risk of injury topersons.

• Magnetic accessories will not work on thissaw.

• NEVER STAND OR SIT ON TOOL, NEVER USE AS A STEPPING STOOL. Serious injury could

occur if the tool is tipped or if the cutting tool is unintentionallycontacted.

• CHECK FOR DAMAGED PARTS. Before further use of the tool, a guard or other part that is

damaged should be carefully checked to determine that it will operate properly and perform its

intended function—check for alignment of moving parts, binding of moving parts, breakage of

parts, mounting and any other conditions that may affect its operation. A guard or other part

that is damaged should be properly repaired or replaced. Do not use tool if switch does not turn it

on and off. Damaged parts can cause further damage to the machine and/or personalinjury.

• DIRECTION OF FEED. Feed work into a blade or cutter against the direction of rotation of the

blade or cutter only. No cove cutting or freehandcuts.

• Check for adequate outfeed distance behind the saw to be sure materials can pass unobstructed

through the cut. Work support tables should be placed in proper locations to fully support

thematerial.

• NEVER LEAVE TOOL RUNNING UNATTENDED. TURN POWER OFF. Don’t leave tool until it

comes to a complete stop. Serious injury canresult.

• NEVER LEAVE MATERIAL ON THE TABLE TOP WHILE THE SAW ISRUNNING.

• DO NOT OPERATE ELECTRIC TOOLS NEAR FLAMMABLE LIQUIDS OR IN GASEOUS OR

EXPLOSIVE ATMOSPHERES. Motors and switches in these tools may spark and ignitefumes.

• STAY ALERT, WATCH WHAT YOU ARE DOING, AND USE COMMON SENSE. DO NOT USE

THE MACHINE WHEN YOU ARE TIRED OR UNDER THE INFLUENCE OF DRUGS, ALCOHOL,

OR MEDICATION. A moment of inattention while operating power tools may result in

seriousinjury.

• DO NOT ALLOW FAMILIARITY (gained from frequent use of this saw) TO REPLACE

SAFETY RULES. Always remember that a careless fraction of a second is sufficient to inflict

severe injury. Use extra caution and stay alert when making repetitive cuts. Turn off saw

frequently to clean up saw dust and check adjustments to reducemonotony.

Additional Safety Rules for Table Saws

• AVOID AWKWARD POSITIONS, where a sudden slip could cause a hand to move into a

sawblade.

• Do not attempt to retrieve materials near the blade on the saw table while the blade isspinning.

• NEVER REACH IN BACK OF, OR AROUND, THE CUTTING TOOL with either hand to hold

down theworkpiece.

• KEEP ARMS, HANDS AND FINGERS AWAY from the blade to prevent seriousinjury.

• USE A PUSH STICK THAT IS APPROPRIATE TO THE APPLICATION TO PUSH WORKPIECES

THROUGH THE SAW. A push stick is a wooden or plastic stick, often homemade, that should be

used whenever the size or shape of the workpiece would cause you to place your hands within 6"

(152mm) of theblade.

• USE HOLD-DOWNS, JIGS, FIXTURES OR FEATHER BOARDS TO HELP GUIDE AND

CONTROL THE WORKPIECE. Accessories for use with your tool are available at extra cost from

your local dealer or authorized service center. Instructions for making a push stick, a narrow rip

auxiliary fence, a push block and feather boards are included in thismanual.

• DO NOT PERFORM RIPPING, CROSSCUTTING OR ANY OTHER OPERATIONFREEHAND.

• NEVER reach around or over sawblade while the blade isspinning.

• STABILITY. Make sure the table saw is firmly mounted to a secure surface before use and does

notmove.

• THE TABLE SAW SHOULD ONLY BE SET UP ON A LEVEL AND STABLE SURFACE. The work

area should be free from obstructions and trip hazards. No materials or tools should be leaned

against thesaw.

• NEVER CUT METALS, CEMENT BOARD OR MASONRY. Certain man-made materials have

special instructions for cutting on table saws. Follow the manufacturer’s recommendations at all

times. Damage to the saw and personal injury mayresult.

• Do not install a diamond masonry blade and attempt to use the table saw as a wetsaw.

• THE PROPER THROAT PLATE MUST BE LOCKED IN PLACE AT ALL TIMES to reduce the risk of

a thrown workpiece and possibleinjury.

• USE THE CORRECT SAW BLADE FOR THE INTENDED OPERATION. The blade must rotate

toward the front of the saw. Always tighten the blade arbor nut securely. Before use, inspect the

blade for cracks or missing teeth. Do not use a damaged or dullblade.

• NEVER ATTEMPT TO FREE A STALLED SAW BLADE WITHOUT FIRST TURNING THE

MACHINE OFF AND REMOVING THE BATTERY PACK. If a workpiece or cut-off piece becomes

trapped inside the blade guard assembly, turn saw off and wait for blade to stop before lifting the

blade guard assembly and removing thepiece.

• NEVER START THE MACHINE with the workpiece against the blade to reduce the risk of a

thrown workpiece and personalinjury.

• DO NOT HAVE ANY PART OF YOUR BODY IN LINE WITH THE BLADE. Personal injury may

occur. Stand to either side of theblade.

• NEVER PERFORM LAYOUT, ASSEMBLY OR SET-UP WORK on the table/work area when

the machine is running. A sudden slip could cause a hand to move into the blade. Severe injury

canresult.

• NEVER PERFORM ANY ADJUSTMENTS WHILE THE SAW IS RUNNING such as fence

repositioning or removal, bevel lock adjustment, or blade heightadjustment.

• CLEAN THE TABLE/WORK AREA BEFORE LEAVING THE MACHINE. Lock the switch in the

“OFF” position and remove the battery pack to prevent unauthorizeduse.

• ALWAYS lock the fence and bevel adjustment beforecutting.

• DO NOT leave a long board (or other workpiece) unsupported so the spring of the board

causes it to shift on the table resulting in loss of control and possible injury. Provide

proper support for the workpiece, based on its size and the type of operation to be performed.

Hold the work firmly against the fence and down against the tablesurface.

• If this saw makes an unfamiliar noise or if it vibrates excessively, cease operating immediately,

turn unit off and remove the battery pack until the problem has been located and corrected.

Contact a

DeWALT

factory service center, a

DeWALT

authorized service center or other qualified

service personnel if the problem can not befound.

• DO NOT OPERATE THIS MACHINE until it is completely assembled and installed according to

the instructions. A machine incorrectly assembled can cause seriousinjury.

• NEVER attempt to cut a stack of loose pieces of material which could cause loss of control or

kickback. Support all materialssecurely.

• DO NOT STORE THIS TOOL WITH THE BATTERY INSTALLED. Think through all scenarios to

ensure that the saw is never turned onaccidentally.

• DO NOT TRANSPORT THIS TOOL WITH THE BATTERYINSTALLED.

• ADDITIONAL INFORMATION regarding the safe and proper operation of power tools (i.e., a

safety video) is available from the Power Tool Institute, 1300 Sumner Avenue, Cleveland, OH

44115-2851 (www.powertoolinstitute.com). Information is also available from the National

Safety Council, 1121 Spring Lake Drive, Itasca, IL 60143-3201. Please refer to the U.S. Department

of Labor OSHA 1910.213Regulations.

Terms: The following terms will be used throughout the manual

and you should become familiar with them.

• Thru-sawing refers to any cut that completely cuts through theworkpiece.

• Non thru-sawing refers to any cut that does not completely cut through theworkpiece.

• Push Stick refers to a wooden or plastic stick, usually homemade, that is used to push small

workpiece through the saw and keeps the operator’s hands clear of theblade.

• Kickback occurs when the saw blade binds in the cut and violently thrusts the workpiece back

toward theoperator. Even more serious and dangerous kickback will result from using the saw

without the guard or riving knife. Material that contacts the outer rim of the blade will be thrown

violently and unpredictably at theoperator.

• Freehand refers to cutting without the use of a miter gauge or rip fence or any other means of

guiding or holding the workpiece other than the operator’shands.



WARNING: Never perform freehand cutting with thissaw.

• Plunge cutting refers to cutting where the workpiece is either lowered down onto the blade with

the workpiece controlled by the user's hands or the workpiece is supported by the user's hands on

the table surface and the blade is then raised up through theworkpiece.



WARNING: Never perform plunge cutting with thissaw.

• Resawing - Flipping material to make a cut the saw is not capable of making in onepass.



WARNING: Do not perform resaw cuts on thissaw.

• Outfeed - The distance behind the saw required to pass the material all the way through thecut.

• Dado cutting - Using a dado head or other type of shaping cutter head to cut dadoes or

decorativegrooves.



WARNING: Do not install dado head or shaping head cutters on thissaw.

Saw Blade Guard Assembly, Anti-kickback Assembly and

Riving Knife

This table saw is equipped with a blade guard assembly with splitter and anti-kickback assembly that

covers the blade and reduces the possibility of accidental blade contact. A riving knife is also provided

for use when making non-thru cuts. The riving knife and splitter are flat plates that are positioned

behind the saw blade and fit into the cut made by the saw blade. Two anti-kickback pawls are

located on the sides of the splitter that allow the wood to pass through the blade in the cutting

direction but reduce the possibility of the material being thrown backwards toward theoperator.

They help prevent kickbacks caused by binding or pinching of the cut material at the back of the

saw blade. The blade guard assembly and anti-kickback assembly can only be used when

making thru-cuts that sever the wood. When making rabbets, dadoes, tenons, lap joints

or other non-thru cuts, the blade guard assembly and anti-kickback assembly must be

removed and the riving knife must be installed.

Use all components of the guarding system (blade guard assembly, riving knife and anti-kickback

assembly) for every operation for which they can be used including all thru-cutting. If you elect not

to use any of these components for a particular application exercise additional caution regarding

control of the workpiece, the use of push sticks, the position of your hands relative to the blade, the

use of safety glasses, the means to avoid kickback and all other warnings contained in this manual

and on the saw itself. Replace the guarding systems as soon as you return to thru-cutting

operations. Keep the guard assembly in workingorder.

Making a Push Stick (Inside Back Cover)

• In order to operate this table saw safely you must use a push stick whenever the size or shape of

the workpiece would cause your hands to be within 6" (152mm) of the saw blade or other cutter.

A push stick is included with thissaw.

• You may need additional push sticks to accommodate materials of different thicknesses. Plans

for making push sticks are included in the back of this instruction manual. Push sticks should

be made from solid wood, plywood, plastic or other strong but soft material. A length of 15.7"

(400mm) is recommended with a notch that fits against the edge of the workpiece to prevent

slipping. It’s a good idea to have several push sticks of the same length (15.7" [400mm] with

different size notches for different workpiecethicknesses.

Kickbacks

Kickbacks can cause serious injury. A kickback occurs when a part of the workpiece binds between

the saw blade and the rip fence, or other fixed object, and rises from the table and is thrown toward

the operator. Kickbacks can be avoided by attention to the followingconditions.

How to Avoid Them and Protect Yourself from Possible Injury

a ) Use the blade guard with splitter, or use the riving knife wheneverpossible.

b ) Be certain that the rip fence is parallel to the sawblade.

c ) Do not rip by applying the feed force to the section of the workpiece that will

become the cut-off (free) piece. Feed force when ripping should always be applied

between the saw blade and the fence; use a push stick for narrow work, 6" (152mm) wide

orless.

d ) Keep saw blade guard assembly, riving knife and anti-kickback assembly in place

and operating properly. If anti-kickback assembly is not operational, return your unit to

the nearest authorized

DeWALT

service center for repair. The splitter and riving knife must be

in alignment with the saw blade and the anti-kickback assembly must stop a kickback once

it has started. Check their action before ripping by pushing the wood under the anti-kickback

assembly. The teeth must prevent the wood from being pulled toward the front of thesaw.

e ) Plastic and composite (like laminate flooring) materials may be cut on this saw.

These materials may have hard or slippery surfaces which limit the effectiveness of the anti-

kickback assembly. When cutting these materials, pay particular attention to the instructions

forripping.

f ) Use saw blade guard assembly, anti-kickback assembly and riving knife for every

operation for which it can be used, including all thru-sawing.

g ) Push the workpiece past the saw blade prior torelease.

h ) NEVER rip a workpiece that is twisted or warped, or does not have a straight edge to

guide along thefence.

i ) NEVER saw a large workpiece that cannot becontrolled.

j ) NEVER use the fence as a guide or length stop whencrosscutting.

k ) NEVER saw a workpiece with loose knots, flaws, nails or other foreignobjects.

l ) NEVER rip a workpiece shorter than 10" (254mm).

m ) NEVER use a dull blade – replace or haveresharpened.



WARNING: ALWAYS use safety glasses. Everyday eyeglasses are NOT safety glasses. Also

use face or dust mask if cutting operation is dusty. ALWAYS WEAR CERTIFIED SAFETY

EQUIPMENT:

• ANSI Z87.1 eye protection (CAN/CSA Z94.3),

• ANSI S12.6 (S3.19) hearing protection,

• NIOSH/OSHA/MSHA respiratoryprotection.



WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other

construction activities contains chemicals known to the State of California to cause cancer,

birth defects or other reproductive harm. Some examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry products, and

• arsenic and chromium from chemically-treatedlumber.

Your risk from these exposures varies, depending on how often you do this type of work. To reduce

your exposure to these chemicals: work in a well ventilated area, and work with approved safety

equipment, such as those dust masks that are specially designed to filter out microscopicparticles.

• Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and

other construction activities. Wear protective clothing and wash exposed areas with

soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote

absorption of harmfulchemicals.



WARNING: Use of this tool can generate and/or disperse dust, which may cause serious

and permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory

protection appropriate for the dust exposure. Direct particles away from face andbody.

NOTICE: Under certain conditions of use, such as extended operation in low-humidity

conditions, or cutting certain materials such as vinyl trim, static charges may build up on

the metal portions of the saw. Touching the metal parts will discharge this static build up

and may result in a short, mild, but harmless electrical shock. However, if you are concerned

about this, you may bring the saw into a

DeWALT

service center for a free inspection to assure

that there is no electrical malfunction of thesaw.

The label on your tool may include the following symbols. The symbols and their definitions are

asfollows:

......................... volts

Hz .......................hertz

min

..................... minutes

or DC ......direct current

...................... Class I Construction (grounded)

…/min ..............per minute

BPM

.................... beats per minute

IPM

..................... impacts per minute

RPM

.................... revolutions per minute

sfpm ................... surface feet per minute

SPM .................... strokes per minute

......................... amperes

........................watts

or AC ...........alternating current

or AC/DC .... alternating or direct current

...................... Class II Construction (double insulated)

no .......................no load speed

.........................rated speed

......................earthing terminal

....................safety alert symbol

.....................visible radiation

..................... wear respiratory protection

..................... wear eye protection

..................... wear hearing protection

BATTERIES AND CHARGERS

The battery pack is not fully charged out of the carton. Before using the battery pack and charger,

read the safety instructions below and then follow charging proceduresoutlined. When ordering

replacement battery packs, be sure to include the catalog number andvoltage.

Your tool uses a

DeWALT

charger. Be sure to read all safety instructions before using your charger.

Consult the chart at the end of this manual for compatibility of chargers and batterypacks.

READ ALL INSTRUCTIONS

Important Safety Instructions for All Battery Packs



WARNING: Read all safety warnings and all instructions for the battery pack,

charger and power tool. Failure to follow the warnings and instructions may result

in electric shock, fire and/or seriousinjury.

• Do not charge or use the battery pack in explosive atmospheres, such as in the presence

of flammable liquids, gases or dust. Inserting or removing the battery pack from the charger

may ignite the dust orfumes.

• NEVER force the battery pack into the charger. DO NOT modify the battery pack in any

way to fit into a non-compatible charger as battery pack may rupture causing serious

personal injury. Consult the chart at the end of this manual for compatibility of batteries

andchargers.

• Charge the battery packs only in designated

DeWALT

chargers.

• DO NOT splash or immerse in water or otherliquids.

• Do not store or use the tool and battery pack in locations where the temperature may

reach or exceed 104°F (40°C) (such as outside sheds or metal buildings in summer). For

best life store battery packs in a cool, drylocation.

NOTE: Do not store the battery packs in a tool with the trigger switch locked on. Never

tape the trigger switch in the ONposition.

• Do not incinerate the battery pack even if it is severely damaged or is completely worn

out. The battery pack can explode in a fire. Toxic fumes and materials are created when lithium

ion battery packs areburned.

• If battery contents come into contact with the skin, immediately wash area with mild

soap and water. If battery liquid gets into the eye, rinse water over the open eye for 15 minutes

or until irritation ceases. If medical attention is needed, the battery electrolyte is composed of a

mixture of liquid organic carbonates and lithiumsalts.

• Contents of opened battery cells may cause respiratory irritation. Provide fresh air. If

symptoms persist, seek medicalattention.



WARNING: Burn hazard. Battery liquid may be flammable if exposed to spark orflame.



WARNING: Fire hazard. Never attempt to open the battery pack for any reason. If the

battery pack case is cracked or damaged, do not insert into the charger. Do not crush, drop

or damage the battery pack. Do not use a battery pack or charger that has received a sharp

blow, been dropped, run over or damaged in any way (e.g., pierced with a nail, hit with

a hammer, stepped on). Damaged battery packs should be returned to the service center

forrecycling.

Transportation



WARNING: Fire hazard. Do not store or carry the battery pack so that metal objects

can contact exposed battery terminals. For example, do not place the battery pack in

aprons, pockets, tool boxes, product kit boxes, drawers, etc., with loose nails, screws, keys, etc.

Transporting batteries can possibly cause fires if the battery terminals inadvertently

come in contact with conductive materials such as keys, coins, hand tools and the

like. The US Department of Transportation Hazardous Material Regulations (HMR) actually

prohibit transporting batteries in commerce or on airplanes in carry-on baggage UNLESS

they are properly protected from short circuits. So when transporting individual battery

packs, make sure that the battery terminals are protected and well insulated from materials

that could contact them and cause a shortcircuit.

Shipping the

DeWALT

FLEXVOLT™ Battery

The D

WALT FLEXVOLT™ battery has two modes: Use and Shipping.

Use Mode: When the FLEXVOLT™ battery stands alone or is in a D

WALT 20V Max* product, it

will operate as a 20V Max* battery. When the FLEXVOLT™ battery is in a 60V Max* or a 120V Max*

(two 60V Max* batteries) product, it will operate as a 60V Max* battery.

Shipping Mode: When the cap is attached to the FLEXVOLT™

battery, the battery is in Shipping Mode. Strings of cells are

electrically disconnected within the pack resulting in three

batteries with a lower watt hour (Wh) rating as compared to one

battery with a higher Watt hour rating. This increased quantity

of three batteries with the lower watt hour rating can exempt the pack from certain shipping

regulations that are imposed upon the higher Watt hourbatteries.

The battery label indicates two Watt Hour Ratings (see example). Depending on how the battery

is shipped, the appropriate Whr rating must be used to determine the applicable shipping

requirements. If utilizing the shipping cap, the pack will be considered 3 batteries at the Whr

indicated for “Shipping”. If shipping without the cap or in a tool, the pack will be considered one

battery at the Watt hour rating indicated next to “Use”.

USE: 120 Wh Shipping: 3 x 40 Wh

example of Use and Shipping label marking

Transport Wh rating indicates 3 x 40 Wh, meaning 3 batteries of 40 Watt hours each. The Use Wh

rating indicates 120 Watt hour (1 battery implied).

Fuel Gauge Battery Packs (Fig. B)

Some

DeWALT

battery packs include a fuel gauge which consists of three green LED lights that

indicate the level of charge remaining in the batterypack.

The fuel gauge is an indication of approximate levels of charge remaining in the battery pack

according to the followingindicators:

75–100% charged

51–74% charged

< 50% charged

Pack needs to be charged

To actuate the fuel gauge, press and hold the fuel gauge button (26). A combination of the three

green LED lights will illuminate designating the level of charge left. When the level of charge in

the battery is below the usable limit, the fuel gauge will not illuminate and the battery will need

to berecharged.

Fig. B

NOTE: The fuel gauge is only an indication of the charge left on the battery pack. It does not

indicate tool functionality and is subject to variation based on product components, temperature

and end-userapplication.

For more information regarding fuel gauge battery packs, please contact call 1-800-4-

DeWALT

(1-800-433-9258) or visit our website www.dewalt.com.

The RBRC® Seal

The RBRC® (Rechargeable Battery Recycling Corporation) Seal on the nickel

cadmium, nickel metal hydride or lithium-ionbatteries (or battery packs)

indicates that the costs to recycle these batteries (or battery packs) at the end

of their useful life have already been paid by

DeWALT

. In some areas, it is illegal

to place spent nickel cadmium, nickel metal hydride or lithium-ion batteries

in the trash or municipal solid waste stream and the Call2Recycle® program provides an

environmentally consciousalternative.

Call 2 Recycle, Inc., in cooperation with

DeWALT

and other battery users, has established the

program in the United States and Canada to facilitate the collection of spent nickel cadmium,

nickel metal hydride or lithium-ion batteries. Help protect our environment and conserve natural

resources by returning the spent nickel cadmium, nickel metal hydride or lithium-ion batteries to

an authorized

DeWALT

service center or to your local retailer for recycling. You may also contact

your local recycling center for information on where to drop off the spent battery. RBRC® is a

registered trademark of Call 2 Recycle,Inc.

RBRC™ is a registered trademark of the Rechargeable Battery RecyclingCorporation.

Important Safety Instructions for All Battery Chargers



WARNING: Read all safety warnings and all instructions for the battery pack,

charger and power tool. Failure to follow the warnings and instructions may result

in electric shock, fire and/or seriousinjury.

• DO NOT attempt to charge the battery pack with any chargers other than the ones in

this manual. The charger and battery pack are specifically designed to worktogether.

• These chargers are not intended for any uses other than charging

DeWALT

rechargeable batteries. Any other uses may result in risk of fire, electric shock orelectrocution.

• Do not expose the charger to rain orsnow.

• Pull by the plug rather than the cord when disconnecting the charger. This will reduce the

risk of damage to the electric plug andcord.

• Make sure that the cord is located so that it will not be stepped on, tripped over or

otherwise subjected to damage orstress.

• Do not use an extension cord unless it is absolutely necessary. Use of improper extension

cord could result in risk of fire, electric shock orelectrocution.

• When operating a charger outdoors, always provide a dry location and use an

extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the

risk of electricshock.

• An extension cord must have adequate wire size (AWG or American Wire Gauge) for

safety. The smaller the gauge number of the wire, the greater the capacity of the cable, that is,

16 gauge has more capacity than 18 gauge. An undersized cord will cause a drop in line voltage

resulting in loss of power and overheating. When using more than one extension to make up

the total length, be sure each individual extension contains at least the minimum wire size. The

following table shows the correct size to use depending on cord length and nameplate ampere

rating. If in doubt, use the next heavier gauge. The lower the gauge number, the heavier thecord.

Minimum Gauge for Cord Sets

Volts

Total Length of Cord in Feet

(meters)

120 V 25 (7.6) 50 (15.2) 100 (30.5) 150 (45.7)

240 V 50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4)

Ampere Rating

American Wire Gauge

Than

Not

Than

0 6 18 16 16 14

6 10 18 16 14 12

10 12 16 16 14 12

12 16 14 12 Not Recommended

• Do not place any object on top of the charger or place the charger on a soft surface that

might block the ventilation slots and result in excessive internal heat. Place the charger in

a position away from any heat source. The charger is ventilated through slots in the top and the

bottom of thehousing.

• Do not operate the charger with a damaged cord orplug.

• Do not operate the charger if it has received a sharp blow, been dropped or otherwise

damaged in any way. Take it to an authorized servicecenter.

• Do not disassemble the charger; take it to an authorized service center when service

or repair is required. Incorrect reassembly may result in a risk of electric shock, electrocution

orfire.

• Disconnect the charger from the outlet before attempting any cleaning. This will reduce

the risk of electric shock. Removing the battery pack will not reduce thisrisk.

• NEVER attempt to connect 2 chargerstogether.

• The charger is designed to operate on standard 120V household electrical power. Do

not attempt to use it on any other voltage. This does not apply to the vehicularcharger.



WARNING: Shock hazard. Do not allow any liquid to get inside the charger. Electric shock

mayresult.



WARNING: Burn hazard. Do not submerge the battery pack in any liquid or allow any liquid

to enter the battery pack. Never attempt to open the battery pack for any reason. If the plastic

housing of the battery pack breaks or cracks, return to a service center forrecycling.



CAUTION: Burn hazard. To reduce the risk of injury, charge only

DeWALT

rechargeable

battery packs. Other types of batteries may overheat and burst resulting in personal injury

and propertydamage.



CAUTION: When battery pack in not in use, keep it away from other metal objects

like paper clips, coins, keys, nails, screws, or other small metal objects that can

make a connection to one terminal to another. Shorting the battery terminals together

may cause burns orfire.

NOTICE: Under certain conditions, with the charger plugged into the power supply, the

charger can be shorted by foreign material. Foreign materials of a conductive nature, such

as, but not limited to, grinding dust, metal chips, steel wool, aluminum foil or any buildup of

metallic particles should be kept away from the charger cavities. Always unplug the charger

from the power supply when there is no battery pack in the cavity. Unplug the charger before

attempting toclean.

Charging a Battery (Fig. C)

1. Plug the charger into an appropriate outlet before inserting batterypack.

Fig. C

2. Insert the battery pack

12

into the charger, making sure the battery pack is fully seated in the

charger. The red (charging) light will blink continuously indicating that the charging process

hasstarted.

3. The completion of charge will be indicated by the red light remaining ON continuously. The

battery pack is fully charged and may be used at this time or left in the charger. To remove

the battery pack from the charger, push the battery release button

13

on the batterypack.

NOTE: To ensure maximum performance and life of lithium-ion battery packs, charge the battery

pack fully before firstuse.

Charger Operation

Refer to the indicators below for the charge status of the batterypack.

DCB101

Charging

Fully Charged

Hot/Cold Pack Delay

Problem Pack or Charger

DCB107, DCB112, DCB113, DCB115, DCB118

Charging

Fully Charged

Hot/Cold Pack Delay*

* DCB107, DCB112, DCB113, DCB115, DCB118: The red light will continue to blink, but a

yellow indicator light will be illuminated during this operation. Once the battery pack has

reached an appropriate temperature, the yellow light will turn off and the charger will resume

the chargingprocedure.

The compatible charger(s) will not charge a faulty battery pack. The charger will indicate faulty

battery pack by refusing to light or by displaying a problem pack or charger blinkpattern.

NOTE: This could also mean a problem with acharger.

If the charger indicates a problem, take the charger and battery pack to be tested at an

authorized servicecenter.

Hot/Cold Pack Delay

When the charger detects a battery pack that is too hot or too cold, it automatically starts a

Hot/Cold Pack Delay, suspending charging until the battery pack has reached an appropriate

temperature. The charger then automatically switches to the pack charging mode. This feature

ensures maximum battery packlife.

A cold battery pack will charge at a slower rate than a warm battery pack. The battery pack will

charge at that slower rate throughout the entire charging cycle and will not return to maximum

charge rate even if the battery packwarms.

The DCB118 charger is equipped with an internal fan designed to cool the battery pack. The fan

will turn on automatically when the battery pack needs to becooled.

Never operate the charger if the fan does not operate properly or if ventilation slots are blocked.

Do not permit foreign objects to enter the interior of thecharger.

Electronic Protection System

Li-Ion tools are designed with an Electronic Protection System that will protect the battery pack

against overloading, overheating or deepdischarge.

The tool will automatically turn off if the Electronic Protection System engages. If this occurs,

place the lithium-ion battery pack on the charger until it is fullycharged.

Wall Mounting

DCB107, DCB112, DCB113, DCB115, DCB118

These chargers are designed to be wall mountable or to sit upright on a table or work surface. If

wall mounting, locate the charger within reach of an electrical outlet, and away from a corner or

other obstructions which may impede air flow. Use the back of the charger as a template for the

location of the mounting screws on the wall. Mount the charger securely using drywall screws

(purchased separately) at least 1" (25.4 mm) long, with a screw head diameter of 0.28–0.35"

(7–9mm), screwed into wood to an optimal depth leaving approximately 7/32" (5.5 mm) of

the screw exposed. Align the slots on the back of the charger with the exposed screws and fully

engage them in theslots.

Charger Cleaning Instructions



WARNING: Shock hazard. Disconnect the charger from the AC outlet before cleaning. Dirt

and grease may be removed from the exterior of the charger using a cloth or soft non-

metallic brush. Do not use water or any cleaningsolutions.

Important Charging Notes

1. Longest life and best performance can be obtained if the battery pack is charged when the air

temperature is between 65°F and 75°F (18° – 24°C). DO NOT charge the battery pack in an

air temperature below +40°F (+4.5°C), or above +104°F (+40°C). This is important and will

prevent serious damage to the batterypack.

2. The charger and battery pack may become warm to the touch while charging. This is a

normal condition, and does not indicate a problem. To facilitate the cooling of the battery

pack after use, avoid placing the charger or battery pack in a warm environment such as in a

metal shed or an uninsulatedtrailer.

3. If the battery pack does not charge properly:

a. Check operation of receptacle by plugging in a lamp or other appliance;

b. Check to see if receptacle is connected to a light switch which turns power off when you

turn out the lights;

c. Move the charger and battery pack to a location where the surrounding air temperature is

approximately 65°F – 75°F (18° – 24°C);

d. If charging problems persist, take the tool, battery pack and charger to your local

servicecenter.

4. The battery pack should be recharged when it fails to produce sufficient power on jobs which

were easily done previously. DO NOT CONTINUE to use under these conditions. Follow the

charging procedure. You may also charge a partially used pack whenever you desire with no

adverse effect on the batterypack.

5. Foreign materials of a conductive nature such as, but not limited to, grinding dust, metal

chips, steel wool, aluminum foil, or any buildup of metallic particles should be kept away from

charger cavities. Always unplug the charger from the power supply when there is no battery

pack in the cavity. Unplug the charger before attempting toclean.

6. Do not freeze or immerse the charger in water or any otherliquid.

Storage Recommendations

1. The best storage place is one that is cool and dry, away from direct sunlight and excess heat

orcold.

2. For long storage, it is recommended to store a fully charged battery pack in a cool dry place

out of the charger for optimalresults.

NOTE: Battery packs should not be stored completely depleted of charge. The battery pack will

need to be recharged beforeuse.

SAVE THESE INSTRUCTIONS FOR

FUTURE USE

Specifications

Table Size 19 X 19" (485 x 485mm)

Miter Angle 30° left and right

Bevel Angle -2° to 47° left

Blade Size 8–1/4" (210mm)

Max. Cut Depth, 0° Bevel 2–9/16" (65mm)

Max. Cut Depth, 45° Bevel 1–3/4" (45mm)

RPM, no load 5800

Unpacking (Fig. D)



WARNING: To reduce the risk of injury, DO NOT install the battery pack until the table saw is

completely assembled and you have read the entire instructionmanual.

Open the box and slide the saw out, as shown in FigureD.

Fig. D

Carefully unpack the table saw and all loose items from the carton. Examine all parts to make sure

that parts have not been damaged during shipping. If any parts are missing or damaged, contact

your dealer to replace them before attempting to assemble thetool.

COMPONENTS (FIG. A)



WARNING: Never modify the power tool or any part ofit. Damage or personal injury

couldresult.

Refer to Figure A at the beginning of this manual for a complete list ofcomponents.

INTENDED USE

This table saw is intended for use by construction professionals for use in ripping, crosscutting,

mitering, beveling and non-through cutting applications in wood, plastic, and other

softmaterials.

DO NOT use for cutting metal, cement board, ormasonry.

DO NOT use dado or shaping cutter heads on thissaw.

DO NOT use under wet conditions or in presence of flammable liquids orgases.

DO NOT let children come into contact with the tool. Supervision is required when inexperienced

operators use thistool.

ASSEMBLY



WARNING: Shock Hazard. To reduce the risk of serious personal injury, turn unit off

and disconnect the battery pack before attempting to move it, change accessories

or make any adjustments. An accidental start-up can causeinjury.

Assembly Order (Fig. A)

1. Unlock and remove the throat plate

17

. Refer to: Removing the Throat Platesection.

2. Make sure blade is installed correctly and arbor nut is tight. Use wrenches

21

stored on the

tool. Refer to FigureA.

3. Position the blade guardassembly

11

4. Attach anti-kickback assembly

14

to the guardassembly.

5. Install and lock throat plate

17

. (NOTE: Adjust leveling screws before proceeding. Refer to

Installing the Throat Plate.)

6. Attach the rip fence

18

. (NOTE: Adjust rip scale before proceeding. Refer to Adjusting the

RipScale.)

NOTE: To attach this table saw to a stand, please follow the instructions included with the

standassembly.

Installing the Throat Plate (Fig. E)

1. Align the throat plate

17

as shown in FigureE, and insert the tabs on the back of the throat

plate into the holes on the back of the tableopening.

2. Rotate cam counterclockwise until the front of throat plate drops into place. Secure by

rotating cam lock knob

27

clockwise 1/4 turn (when cam lock is under the table holding the

throat plate in place).

3. The throat plate includes four adjustment screws

28

which raise or lower the throat plate.

When properly adjusted, the front of the throat plate should be flush or slightly below the

surface of the table top and secured in place. The rear of the throat plate should be flush or

slightly above the tabletop.

Fig. E

Removing the Throat Plate

1. Remove the throat plate

17

by turning the cam lock knob

27

1/4 turn counterclockwise

2. Using finger hole

29

on the plate, pull throat plate up and forward to expose the inside of

the saw. DO NOT operate the saw without the throatplate.



WARNING: To reduce the risk of serious personal injury, the throat plate must be locked in

place at alltimes.

Installing/Replacing the Blade (Fig. A, E, F)

1. Raise the saw blade arbor to its maximum height by turning the blade height adjustment

wheel

6

clockwise.

2. Remove the throat plate

17

3. Remove the arbor nut

30

and clamp washer

31

from the saw arbor by

turningcounterclockwise.

Fig. F

31 30

4. Place the saw blade on to the arbor

32

making sure the teeth of the blade

2

point down at

the front of the table. Assemble the clamp washer

31

and arbor nut to the arbor and tighten

arbor nut

30

as far as possible by hand, making sure that the saw blade is against the inner

flange and the clamp washer is against the blade. Ensure the largest diameter of the clamp

washer is against the blade. Ensure the arbor and clamp washer are free from dust anddebris.

5. Use the open end of the wrench

21

to keep the arbor from rotating when tightening the

arbornut.

6. Using the other wrench, tighten the arbor nut

30

by turning itclockwise.

7. NOTE: Different types of blades make different kerfs (width of cuts). Therefore, it is necessary

to check adjustment of rip scale when changing blades. Replacement blade MUST not

exceed the thickness stated on the riving knife. The riving knife provided with the saw is

1.6mmthick.

Installing/Removing the Blade Guard Assembly and Riving Knife

(Fig. G)



WARNING: Use blade guard assembly for all thru-sawing.

NOTE: The saw is shipped with the non thru sawing riving knifeinstalled.

1. Raise the saw blade arbor to its maximumheight.

2. Loosen the riving knife lock knob

33

(minimum of three turns).

3. To disengage riving knife lock pin, push lock knob toward the riving knife as indicated by the

yellow arrows on theknob.

4. While pushing the lock knob, lift the riving knife out of the clamp. Then slide the blade guard

assembly into the clamp until it bottomsout.



WARNING: Do not insert both blade guard assembly and riving knife into the clamp at the

sametime.

5. Release the lock knob to engage the lock pin. Give the blade guard a slight pull upwards to

ensure pin is engaged.

6. Tighten the riving knife lockknob.

7. Reinstall the throatplate.

8. To remove the bladed guard assembley, follow these steps in reverseorder.

NOTE: Follow the same steps above for riving knifeinstalation.

Fig. G



WARNING: Before inserting the battery into the table saw or operating the saw, always

inspect the blade guard assembly and riving knife for proper alignment and clearance with

saw blade. Check alignment after each change of bevelangle.

NOTE: DO NOT operate saw if riving knife lock pin is not locked into the blade guard or

rivingknife.

When properly aligned, the riving knife will be in line with the blade at both table top level,

and at the top of the blade. Using a straight edge, ensure that the blade

2

is aligned with the

riving knife

23

as shown in Figure G. Operate the blade tilt and height adjustments through the

extremes of travel and ensure the blade guard assembly clears the blade in all operations and

that the anti-kickback assembly isfunctioning.

Assembling the Rip Fence (Fig. H)

The rip fence can be installed in two positions on the right (position 1 for 0" to 20" ripping, and

position 2 for 4" to 24" ripping) and one position on the left of your tablesaw.

1. Align the locator pins

34

on the fence rails with the slots

35

on each fenceend.

2. Place fence onto the rail as shown in FigureH maintaining pin and slot alignment on both

ends of thefence.

3. Secure the rip fence by snapping down the latches

19

to the rails. Be sure to snap both front

and rear latches inplace.

Fig. H

Position 1

Position 2

Adjusting the Rip Scale (Fig. I)

1. Unlock the rail lock lever

5

2. Set the blade at 0° bevel and move the fence in until it touches theblade.

3. Lock the rail locklever.

4. Loosen the rip scale indicator screws

36

and set the rip scale indicator to read zero (O)

Retighten the rip scale indicator screws. The yellow rip scale (top) reads correctly only when

the fence is mounted on the right side of the blade and is in position 1 (for 0 to 20" ripping)

[not the 24" rip position]. The white scale (bottom) reads correctly only when the fence is

mounted on the right side of the blade and in position 2 (for 4" to 24" ripping).

A metric scale is available at an additional cost, refer to Accessories fordetails.

Fig. I

Anti-Kickback Assembly (Fig. J)



WARNING: To reduce the risk of serious personal injury, the anti-kickback assembly must be

in place for all possiblecuts.

1. Remove the anti-kickback assembly

14

from the storage position by depressing the stem.

Refer toStorage.

2. Locate the anti-kickback mounting slot

37

at the top rear of the blade guard assembly

11

3. Align the stem

38

with the mounting slot. Depress the stem and push down on the anti-

kickback assembly

14

until it snaps and locks intoplace.

4. To remove the anti-kickback assembly, depress the stem and pull up and out of the

mountingslot.

With battery removed, operate the blade tilt and height adjustments through the extremes of

travel and ensure the blade guard assembly clears the blade in all operations and that the anti-

kickback assembly isfunctioning.

Fig. J

Bench Mounting (Fig. A)

NOTE: A portable table saw stand is designed for use with this saw and is available at a local

DeWALT

dealer or service center at extracost.



WARNING: To reduce the risk of serious personal injury, turn unit off and remove the

battery pack before making any adjustments or removing/installing attachments

oraccessories. An accidental start-up can causeinjury.



WARNING: To reduce the risk of injury, the saw must be secured to prevent unintended

movement duringuse.

The table saw must be securely mounted on a stand, workbench or other rigid and stable support

so that the saw does not move while cutting and cannot be overturned by large overhanging

pieces of material. Four mounting holes

9

are provided in the metal frame to allow the table saw

to be secured to a stand or other means ofsupport.

1. Center the saw on the desired, stable worksurface.

2. Drive four 3-1/2" (88.9 mm) long screws through the holes

9

in the metal frame. Make sure

the screws extend through the frame and securely attach to the supporting worksurface.

NOTE: If marring the supporting work surface is a concern, the table saw can be mounted to

scrap wood which can then be clamped onto the desired worksurface.

3. Cut a piece of 3/4" (19 mm) plywood to fit beneath the footprint of thesaw.

4. Screw the saw to the plywood and clamp the overhang of the plywood to the work surface. If

the screws protrude through the plywood base, set it on two scrap pieces of material of equal

thickness and attach them to the edges of the plywood to hold the saw further off of the

work surface and prevent the screws from marring thesurface.

ASSEMBLY AND ADJUSTMENTS



WARNING: To reduce the risk of serious personal injury, turn unit off and remove the

battery pack before making any adjustments or removing/installing attachments

oraccessories. An accidental start-up can causeinjury.

NOTE: This saw is fully and accurately adjusted at the factory at the time of manufacture. If

readjustment due to shipping and handling or any other reason is required, follow the sections

below to adjust thissaw.

Once made, these adjustments should remain accurate. Take a little time now to follow these

directions carefully to maintain the accuracy of which this saw iscapable.

Rail Lock Adjustment (Fig. I, K)

(Tightening Fence Clamping System)

1. Lock the rail lock lever

5

2. On the underside of the saw, loosen the jam nut

39

3. Tighten the hex rod

40

until the spring on the locking system is more compressed, (not fully

compressed) creating the desired tension on the rail lock lever. Retighten the jam nut against

the hexrod.

4. Check that the fence does not move when the lock lever is engaged. If the fence is still loose,

tighten the springfurther.

Fig. K

Rip Scale Adjustment

See Adjusting the Rip Scale underAssembly.

Adjusting Blade Alignment (Fig. L)

(Blade Parallel to Miter Slot)



WARNING: Cut Hazard. Check the blade at 0˚ and 45˚ to make sure blade does not hit the

throat plate, causing personalinjury.

If the blade appears to be out of alignment with the miter slot on the table top, it will require

calibration for alignment. To realign the blade and miter slot, use the following procedure:



WARNING: To reduce the risk of serious personal injury, turn unit off and remove the

battery pack before making any adjustments or removing/installing attachments

oraccessories. An accidental start-up can causeinjury.

Fig. L

1. Using a 5mm hex wrench, loosen rear pivot bracket fasteners

41

just enough to allow the

bracket to move side-to-side.

2. Adjust the bracket until the blade is parallel to the miter gaugeslot.

3. Tighten the rear pivot bracket fasteners to 110–120 in-lbs (12.5–13.6 Nm).

Bevel Stop and Pointer Adjustment (Fig. M)

1. Raise the blade fully by rotating the blade height adjustment wheel

6

clockwise until itstops.

2. Unlock the bevel lock lever

7

by pushing it up and to the right. Loosen the bevel

stopscrew

42

3. Place a square

45

flat against the table top and against the blade between teeth, as shown

in FigureM. Ensure the bevel lock lever is in its unlocked, or up,position.

4. Using the bevel lock lever, adjust the bevel angle until it is flat against thesquare.

5. Tighten the bevel lock lever by pushing itdown.

6. Turn the bevel stop screw

42

to rotate the cam until it firmly contacts the bearing block.

Tighten the bevel stop screw

42

7. Check the bevel angle scale. If the pointer does not read 0°, loosen pointer screw

44

and

move the pointer so it reads correctly. Retighten the pointerscrew.

8. Repeat at 45°, but do not adjustpointer.

Fig. M

Fence Alignment Adjustment (Fig. H, N)

(Blade Parallel to Fence)

If you experience fence alignment problems and want to correct an out of parallel alignment

between the fence and the blade, be sure to check the alignment of the blade to the miter slot

first. After confirming that those elements are aligned, proceed with alignment of the blade to

the fence using the following procedure:

Position 2Position 1

Fig. N

34 34

Position 1 Fence Alignment

1. Install the fence in position 1 (Refer to Figure H) and unlock the rail lock lever

5

. Locate both

locator pins 

34

that support the fence on the front and rearrails.

2. Loosen the rear locator pin screw and adjust the allignment of the fence in the groove until

the fence face is parallel to the blade. Make sure you measure from the fence face to the front

and back of the blade to ensurealignment.

3. Tighten the locator pinscrew.

4. Check rip scale pointeradjustment.

NOTE: Follow the Position 1 Fence Alignment instructions for aligning the fence on the left of

theblade.

Position 2 Fence Alignment

1. To align position 2 fence locator pins, ensure position 1 pins have been aligned, refer to

Position 1 FenceAlignment.

2. Loosen the position 2 locator pins, then using holes in the blade wrench

21

as a guide for

positioning, align the pins (Fig.N).

3. Tighten the locator pins (front and rear).

Aligning Riving Knife to Blade (Fig. O)

1. Remove the throat plate. Refer to Removing the Throat Plate underAssembly.

2. Raise the blade to full depth of cut and 0° bevelangle.

3. Locate the three small set screws

50

adjacent to the riving knife lock knob

33

. These screws

will be used to adjust the riving knifeposition.

4. Lay a straight edge on the table against two blade tips. The riving knife should not touch the

straightedge.

5. If needed, loosen the two larger lock screws

51

6. Use the small set screws

50

to adjust the riving knife position. Lay the straight edge on the

opposite side of the blade and repeat adjustments asneeded.

7. Lightly tighten the two larger lock screws

51

8. Place a square flat against the riving knife to verify the riving knife is vertical and in-line with

theblade.

9. If needed, use the set screws to bring the riving knife vertical with thesquare.

10. Repeat step 4 to verify position of rivingknife. Repeat 5 thru 9 ifnecessary.

11. Fully tighten the two larger lock screws

51

Fig. O

5151

Saw Blades



WARNING: Riving knives must be matched to saw blade dimensions in order to function

effectively. Refer to Splitter and Riving KnifeSelection. Use only 8-1/4" (210mm)

diameter blades with this tablesaw.

• The saw blade furnished with your new saw is a 8-1/4" (210mm) combination blade, used for

crosscutting (across the grain) and ripping (with the grain) through the material. The center

hole to fit on the arbor is 5/8" (16mm) diameter. This blade will produce a good quality cut for

mostapplications.

• There are many types of blades available to do specific and special jobs such as cross cut only, rip

only, hollow ground, thin plywood, paneling,etc.

• Use only saw blades designed for maximum safe operating speeds of 6,000RPM orgreater.

• Saw blades should always be kept sharp. It is recommended that you locate a reputable

sharpening service to sharpen your blades whenneeded.

• Never stack blades on top of one another to store. Place material such as cardboard between

them to keep the blades from coming in contact with oneanother.



WARNING: To reduce the risk of injury, abrasive wheels or blades (including diamond)

should not be used on thissaw.

Splitter and Riving Knife Selection (Fig. P)



WARNING: To minimize the risk of kickback and to ensure proper cutting, the splitter and

riving knife must be the proper thickness for the bladeused.

The splitter and riving knife supplied with this table saw is the correct size for the blade supplied

with thesaw.

If a different blade is used, check the blade body (plate) thickness and the blade kerf (cutting)

width marked on the blade or on the blade packaging. The splitter and riving knife thickness

must be greater than the body thickness and less than the kerf width as shown in FigureP.

Riving knife thickness

Kerf width (width of cut

made by the blade)

Body (or plate)

thickness of the blade

Fig. P

The riving knife provided with this saw is marked as follows:

.063” (1.6mm) THICK RIVING KNIFE. ONLY FOR USE WITH 8 ¼” (210mm) BLADE WITH .071”

(1.8mm) MIN KERF WIDTH AND .055” (1.4mm) MAX BODYTHICKNESS.

Blade body thickness and kerf width dimensions for all

DeWALT

table saw blades are available at

www.dewalt.com

If a different blade is used and the body thickness and kerf width dimensions are not provided,

use the following procedure to determine the correct riving knife thickness:

1. Measure the body thickness of theblade.

2. Make a shallow cut in scrap material and measure the kerfwidth.

3. Select the riving knife

23

4. Slide the riving knife through the shallow cut made in step 2 to confirm the correct riving

knife has been selected. The riving knife should not bind or drag through thecut.



WARNING: If any dragging or binding of the material is encountered as it reaches the riving

knife, turn unit off and remove the battery pack. Repeat steps 1–4 to make the proper riving

knife selection before attempting anothercut.

Kickback

Kickback is a dangerous condition! It is caused by the workpiece binding against the blade. The

result is that the workpiece can move rapidly in a direction opposite to the feed direction. During

kickback, the workpiece could be thrown back at the operator. It can also drag the operator’s

hand back into the blade if the operator’s hand is at the rear of the blade. If kickback occurs, turn

the saw OFF and verify the proper functioning of the riving knife, anti-kickback assembly and

blade guard assembly before resumingwork.



WARNING: See Additional Safety Rules for Table Saws and follow all warnings

provided regardingKICKBACK.

OPERATION



WARNING: To reduce the risk of serious personal injury, turn unit off and remove the

battery pack before making any adjustments or removing/installing attachments

oraccessories. An accidental start-up can causeinjury.



WARNING: Before using the saw, verify the following each and every time:

• ALWAYS wear proper eye, hearing and respiratoryequipment.

• Blade is securelytightened.

• Bevel angle and rail lock levers arelocked.

• If ripping, ensure that rip fence locked lever is locked and that the fence is parallel to

theblade.

• If crosscutting, miter gage knob is securelytightened.

• The blade guard assembly is properly attached and the anti-kickback assembly

isfunctioning.

• ALWAYS inspect the blade guard assembly and riving knife for proper alignment,

operation and clearance with sawblade.

• ALWAYS make sure both guards are in the down position in contact with the table

beforeoperating.



WARNING: To reduce the risk of serious personal injury, have push stick ready to use before

startingcut.

Failure to adhere to these common safety rules can greatly increase the likelihood ofinjury.



WARNING: Before installing the battery in the table saw or operating the saw, always

inspect the blade guard assembly and riving knife for proper operation alignment and

clearance with sawblade.



WARNING: Ripping or crosscutting may cause saw to tip over while operating. Make sure

saw is securely mounted to a stablesurface.



WARNING: Never use the fence and miter gauge together. This may cause a kickback

condition and injure theoperator.



CAUTION: If this saw makes an unfamiliar noise or if it vibrates excessively, cease operating

immediately, turn unit off and remove the battery pack until the problem has been located

and corrected. Contact a

DeWALT

factory service center, a

DeWALT

authorized service center

or other qualified service personnel if the problem cannot befound.



WARNING: The proper throat plate must be in place at all times to reduce the risk of a

thrown workpiece and possibleinjury.

There are two basic types of cutting with table saws: ripping and crosscutting. Regardless of

material, man made or natural wood, the distinction between ripping and crosscutting is as

follows: Ripping is cutting to a different width (usually with the grain) and crosscutting describes

cutting material across the shorter dimension (usually against the grain).



WARNING: When ripping, always use the fence to provide a guide for the material and blade

guard assembly to protect against a kickbacksituation.



WARNING: Never perform any cutting operation free hand. Never perform plungecutting.



WARNING: When crosscutting, aways use the miter gage. Do not use both the rip fence and

miter gagetogether.

Installing and Removing the Battery Pack (Fig. Q)

NOTE: For best results, make sure your battery pack is fullycharged.

To install the battery pack

12

into the tool, align the battery pack with the rails inside the tool

and slide it in until the battery pack is firmly seated and ensure that it does notdisengage.

To remove the battery pack from the tool, press the release button

13

and firmly pull the battery

pack out of the tool. Insert it into the charger as described in the charger section of thismanual.

Fig. Q

On-Off Switch Operation (Fig. R)



WARNING: To reduce the risk of injury, be sure the switch is in the OFF position before

installing thebattery.

Lift the red paddle and push green button

52

in to turn this sawon.

Push the red button

53

or push down the red paddle

54

to turn this sawoff.

Locking Off the Saw

The On-Off switch may be locked to prevent unauthorized operation of the saw. To lock the

switch in the Off position, insert a padlock through the red handle and hole

55

. Padlock must

not exceed a maximum diameter of 1/4"(6.35mm).

Fig. R

Guard Operating Feature (Fig. S)



WARNING: To reduce the risk of serious personal injury, turn unit off and remove the

battery pack before making any adjustments or removing/installing attachments

oraccessories. An accidental start-up can causeinjury.

1. The guard arms

56

will lock in place when in the raisedposition.

2. This feature improves visability when measuring the blade to fencedistance.

3. Push down on guard(s) and they will release to the operatingposition.

NOTE: Pull on the anti-kickback assembly to ensure it is locked inplace.

ALWAYS make sure both guards are in the down position in contact with the table

beforeoperating.

Fig. S

Rip Fence Operation (Fig. A, T)

Rail lock lever (Fig. A)

The rail lock lever

5

locks the fence in place preventing movement during cutting. To lock the

rail lever, push it down and toward the rear of the saw. To unlock, pull it up and toward the

front of thesaw.



WARNING: When ripping, always lock the rail locklever.

Work Support Extension/Narrow Ripping Fence (Fig. T)

The table saw is equipped with a narrow ripping fence that also supports work that extends

beyond the sawtable.

To use the narrow ripping fence in the work support position, rotate it from its stored position as

shown in Figure T, and slide the pins into the lower sets of slots

57

on both ends of thefence.

To use the narrow ripping fence in the narrow ripping position, snap the pins into the upper sets

of slots

58

on both ends of thefence.

This feature will allow 2" (51mm) of extra clearance to the blade. Refer to figureT.

Fig. T

NOTE: When not in use, the narrow ripping fence should be placed in its storedposition.

NOTE: This fence will allow the guard to remain on the saw when completing narrow ripping.

This fence will provide ample space for a push stick.

Fine Adjustment Knob (Fig. A)

The fine adjustment knob

4

allows smaller adjustments when setting the fence. Before adjusting,

be sure the rail lock lever is in its up or unlockedposition.

Rip Scale Pointer

The rip scale pointer will need to be adjusted for proper performance of the rip fence if the user

switches between thick and thin kerf blades. The rip scale pointer only reads correctly for position

1 (0 to 24"), however for position 1 with narrow rip fence in use add 2" (51 mm). See Adjusting

the Rip Scale underAssembly.

Ripping (Fig. U)



WARNING: Never touch the “free end” of the workpiece or a “free piece” that is cut off, while

the power is ON and/or the saw blade is rotating. Piece may contact the blade resulting in a

thrown workpiece and possibleinjury.



WARNING: A rip fence should ALWAYS be used for ripping operations to prevent loss of

control and personal injury. NEVER perform a ripping operation freehand. ALWAYS lock the

fence to therail.



WARNING: When bevel ripping and whenever possible, place the fence on the side of the

blade so that the blade is tilted away from the fence andhands.



WARNING: Keep hands clear of theblade.



WARNING: Use a push stick to feed the workpiece if there is 2–6" (51–152mm) between the

fence and the blade. Use a narrow ripping fence feature and push block to feed the workpiece

if there is 2" (51mm) or narrower between the fence and theblade.

1. Lock the rip fence by pressing the rail lock lever down. Remove the mitergauge.

2. Raise the blade so it is about 1/8" (3.2mm) higher than the top of theworkpiece.

3. Hold the workpiece flat on the table and against the fence. Keep the workpiece about 1"

(25.4mm) away from theblade.

Fig. U



WARNING: The workpiece must have a straight edge against the fence and must not be

warped, twisted or bowed. Keep both hands away from the blade and away from the path of

the blade. See proper hand position in FigureU.

4. Turn the saw on and allow the blade to come up to speed. Both hands can be used in starting

the cut. When there is approximately 12" (305mm) left to be ripped, use only one hand, with

your thumb pushing the material, your index and second finger holding the material down

and your other fingers hooked over the fence. Always keep your thumb along side your first

two fingers and near thefence.

5. Keeping the workpiece against the table and fence, slowly feed the workpiece rearward all

the way through the saw blade. Continue pushing the workpiece until it is clear of the blade

guard assembly and it falls off the rear of the table. Do not overload themotor.

6. Never try to pull the workpiece back with the blade turning. Turn the switch off, allow the

blade to stop, raise the anti-kickback teeth on each side of the riving knife if necessary and

slide the workpieceout.

7. When sawing a long piece of material or a panel, always use a work support. A sawhorse,

rollers, or out feed assembly provides adequate support for this purpose. The work support

must be at the same height or slightly lower than the sawtable.



WARNING: Never push or hold onto the free or cut-off side of the workpiece if it is between

the blade and thefence.

Ripping Small Pieces

It is unsafe to rip small pieces. It is not safe to put your hands close to the blade. Instead, rip a

larger piece to obtain the desired piece. When a small width is to be ripped and the hand cannot

be safely put between the blade and the rip fence, use one or more push sticks. A pattern is

included at the end of this manual to make push sticks. A push stick

22

is included with this saw,

attached to the rip fence. Use the push stick(s) to hold the workpiece against the table and fence,

and push the workpiece fully past theblade. The narrow ripping fence feature on the table saw

may be used for some narrow rip cuts. You may also use an auxiliary narrow rip fence. Instructions

for making an auxiliary fence are provided in the back of themanual.

Bevel Ripping

This operation is the same as ripping except the bevel angle is set to an angle other than zero

degrees. For proper hand position, Refer to figureV.

Fig. V



WARNING: Before installing the battery pack or operating the saw, always inspect the blade

guard assembly and riving knife for proper alignment and clearance with saw blade. Check

alignment after each change of bevelangle.

Crosscutting (Fig. V)



WARNING: NEVER use rip fence in combination with mitergage.



WARNING: NEVER touch the “free end” of the workpiece or a “free piece” that is cut off, while

the power is ON and/or the saw blade is rotating. Piece may contact the blade resulting in a

thrown workpiece and possibleinjury.



WARNING: To reduce the risk of injury, NEVER use the fence as a guide or length stop

whencrosscutting.



WARNING: NEVER use a length stop on the free end of the workpiece when crosscutting.

In short, the cut-off piece in any thru-sawing (cutting completely through the workpiece)

operation must never be confined — it must be allowed to move away from saw blade to

prevent contact with blade resulting in a thrown workpiece and possiblyinjury.



WARNING: Use caution when starting the cut to prevent binding of the blade guard

assembly against the workpiece resulting in damage to saw and possibleinjury.



WARNING: When using a block as a cut-off gauge, the block must be at least 3/4" (19mm)

thick and is very important that the rear end of the block be positioned so the workpiece

is clear of the block before it enters the blade to prevent contact with blade resulting in a

thrown workpiece and possiblyinjury.

1. Remove the rip fence and place the miter gauge in the desiredslot.

2. Adjust the blade height so that the blade is about 1/8" (3.2mm) higher than the top of

theworkpiece.

3. Hold the workpiece firmly against the miter gauge

10

with the path of the blade in line with

the desired cut location. Keep the workpiece an inch or so in front of the blade. KEEP BOTH

HANDS AWAY FROM THE BLADE AND THE PATH OF THE BLADE (Fig. V).

4. Start the saw motor and allow the blade to come up tospeed.

5. While using both hands to keep the workpiece against the face of the miter gauge, and

holding the workpiece flat against the table, slowly push the workpiece through theblade.

6. Never try to pull the workpiece with the blade turning. Turn the switch off, allow the blade to

stop, and carefully slide the workpieceout.



WARNING: Never touch or hold onto the free or cut-off end of theworkpiece.

Bevel Crosscutting

This operation is the same as crosscutting except that the bevel angle is set to an angle other

than 0°.



WARNING: Before connecting installing the battery pack or operating the saw, always

inspect the blade guard assembly and riving knife for proper alignment and clearance with

saw blade. Check alignment after each change of bevelangle.

Mitering (Fig. W)



WARNING: Miter angles greater than 45˚ may force the blade guard assembly into the saw

blade causing damage to the blade guard assembly and personal injury. Before starting

the motor, test the operation by feeding the workpiece into the blade guard assembly. If

the blade guard assembly contacts the blade, place the workpiece under the blade guard

assembly, not touching the blade, before starting themotor.



WARNING: Certain workpiece shapes, such as molding may not lift the blade guard

assembly properly. Feed the workpiece slowly to start the cut. If the blade guard assembly

contacts the blade, place the workpiece under the blade guard assembly, not touching the

blade, before starting themotor.

This operation is the same as crosscutting except the miter gauge is locked at an angle other than

0°. Hold the workpiece FIRMLY against the miter gauge

10

and feed the workpiece slowly into

the blade (to prevent the workpiece from moving).

Fig. W

Miter Gauge Operation

To set your miter gauge:

1. Loosen the miter gauge lockknob

59

2. Move the miter gauge to the desiredangle.

3. Tighten the miter gauge lockknob.

Compound Mitering

This is a combination of bevel crosscutting and mitering. Follow the instructions for both bevel

crosscutting andmitering.

Dust Collection (Fig. X)

This table saw is equipped with a dustshroud and dust collection port. For best results, connect a

vacuum to the port at the rear of the saw and on the guard using a Y connector. The Y connector

is available as an accessory at additional cost. Refer toAccessories.

NOTICE: Care should be taken to position hoses to not interfere with cuttingoperation.



WARNING: To prevent accidental start up, remove battery from the saw before cleaning out

dust collectionsystem.

1. Turn the saw on its side, so the bottom, open part of the unit isaccessible.

2. Open the dust access door

60

shown by removing 2 wingscrews

61

and detaching the

door. Clean out the excess dust, and re-attach door, securing it with the wingscrews.

Fig. X

Motor Overload and Power Loss Reset Switch

If power is interrupted by a dead battery or power is lost, the saw contains a power loss reset

switch feature that will automatically reset to OFFposition.

Short battery life is often the result of a dull blade. Change your blade on a regular basis to

increase batterylife.

Lubrication (Fig. X)

1. All motor bearings are permanently lubricated at the factory and no additional lubrication

isneeded.

2. The height adjustment screw may require periodic cleaning and lubrication. If you have

difficulty raising or lowering the blade:

a. Remove the battery from thesaw.

b. Turn the saw on its side, so the bottom, open part of the unit isaccessible.

c. Clean and lubricate the height adjustment screw threads

62

on the underside of this saw

with general purpose grease. Refer to FigureX.

STORAGE (FIG. Z)

1. Attach push stick

22

tofence.

2. Depress the stem on the anti-kickback assembly

14

to allow the assembly to slide from the

riving knifeslot.

3. Position anti-kickback assembly into storage as shown. While depressing stem, slide the anti-

kickback assembly across the storage bracket

63

and release pin to lock intoplace.

4. Remove blade guard assembly

11

. Refer to Installing/Removing the Blade Guard

Assembly and Riving Knife. Place blade guard assembly into holder as shown, then turn lock

1/4 turn to lock inplace.

5. Slide closed end of blade wrenches

21

into catch then secure in place with wingnut.

6. Insert guide bar of miter guage

10

into pocket until it bottomsout.

7. Non thru-sawing riving knife

23

slides in place on back side of guard storage clip.

8. To store fence

18

, snap work support in stored position. Remove fence from rails. Reattach

fence upside down on left side of saw. Pivot fence lock latches tosecure.

Fig. Z

10 14

Accessory Construction for Alternative Operation Methods

Narrow Rip Auxiliary Fence (Fig. AA–CC)

The narrow rip auxiliary fence should be used for a rip measuring 2" (51mm) or narrower. This

fence will allow the guard to remain on the saw when completing narrow ripping. This fence will

provide ample space for proper use of a push block (

66

, see Push Block).

1. Follow the diagram in Fig. AA to construct the narrow rip auxiliary fence

69

NOTE: The length should be cut to fit the length

64

of the saw table top and sides

65

must

beparallel.

3/8"

(9.5 mm)

(25 mm)

1/2"

(12.7 mm)

Fig. AA

4-3/4"

(121 mm)

3/8"

(9.5mm)

2. After the narrow rip auxiliary fence is constructed, slip it over the saw table top and place it

flush to the fence as shown in FigureCC.

3. Feed the workpiece through until the edge of the material reaches the front edge of the saw

tabletop.

4. Continue feeding the material using the push block

66

until the cut iscomplete.

Push Block (Fig. BB, CC)

IMPORTANT: Only use the push block

66

with the narrow rip auxiliary fence, refer to Narrow

Rip Auxiliary Fence. The push block should be used once the material being cut reaches the saw

tabletop.

1. Construct a push block using the diagram in FigureBB.

NOTE: Edges

67

must beparrallel.

IMPORTANT: The over hanging edge

68

Fig. BB) MUST be square. An uneven lip could

cause the push block to slip or push the material away from thefence.

(305mm)

Fig. BB

2-1/2" (64mm)

(127 mm)

1/2"

(12.7 mm)

4-3/4"

(121 mm)

12"

(305 mm)

1/2"

(12.7 mm)

5-1/4"

(133 mm)

2-1/2"

(64 mm)

1/2"

(12.7 mm)

2. Place the push block

66

(Fig. CC) behind the material and ensure the lip of the block is flush

to the narrow rip auxiliary fence

69

3. Once the push block is in place, continue feeding the material until the cut is complete

making sure the push block remains flush to the narrow rip auxiliary fence at alltimes.

IMPORTANT: The narrow rip auxiliary fence and the over hanging edge

68

Fig. BB) should both

be the samethickness.

Fig. CC

Featherboard Construction (Fig. DD, EE)

Featherboards are used to keep the work in contact with the fence and table, and help prevent

kickbacks. Dimensions for making a typical featherboard are shown in Figure DD. Make

the featherboard from a straight piece of wood that is free of knots and cracks. Clamp the

featherboard to the fence and table so that the leading edge of the featherboard will support the

workpiece until the cut is complete (Fig. EE). An 8" (203mm) high flat board can be clamped to

the rip fence and the featherboard can be clamped to the 8" (203mm) highboard.

60º

Fig. DD

24" (610mm)

5" (127mm)

3/4"

(20mm)

The kerf should

be about 1/4"

(6.4mm) apart

(102mm)



WARNING: Use featherboards for all non thru-sawing operations where the blade guard

assembly, anti-kickback assembly and riving knife cannot be used. Always replace the

blade guard assembly, anti-kickback assembly and riving knife when the non thru-

sawing operation is complete. Make sure the featherboard presses only on the portion of

the workpiece in front of theblade.

Fig. EE

MAINTENANCE



WARNING: To reduce the risk of serious personal injury, turn unit off and remove the

battery pack before making any adjustments or removing/installing attachments

oraccessories. An accidental start-up can causeinjury.

Cleaning



WARNING: Blow dirt and dust out of all air vents with clean, dry air at least once aweek.

To minimize the risk of eye injury, always wear ANSIZ87.1 approved eye protection when

performingthis.



WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic parts

of thetool. These chemicals may weaken the plastic materials used in theseparts. Use a

cloth dampened only with water and mildsoap. Never let any liquid get inside the tool; never

immerse any part of the tool into aliquid.

Accessories



WARNING: Since accessories, other than those offered by

DeWALT

, have not been tested

with this product, use of such accessories with this tool could behazardous. To reduce the

risk of injury, only

DeWALT

recommended accessories should be used with thisproduct.

Recommended accessories for use with your tool are available at extra cost from your local dealer

or authorized servicecenter. If you need assistance in locating any accessory, please contact

DeWALT

Industrial ToolCo., 701East Joppa Road, Towson, MD 21286, call 1–800–4-

DeWALT

(1–800–433–9258) or visit our website:www.dewalt.com.

• Compatible Stands (DWE74911)

• Metric rip scale (N458905)

• Dust extraction Y connector (contact your local dealer)

Repairs

The charger and battery pack are notserviceable.



WARNING: To assure product SAFETY and RELIABILITY, repairs, maintenance and

adjustment (including brush inspection and replacement) should be performed by a

DeWALT

factory service center or a

DeWALT

authorized servicecenter. Always use identical

replacementparts.

Thank you for yourpurchase. Register your product nowfor:

• WARRANTY SERVICE: Registering your product will help you obtain more efficient warranty

service in case there is a problem with yourproduct.

• CONFIRMATION OF OWNERSHIP: In case of an insurance loss, such as fire, flood or theft,

your registration of ownership will serve as your proof ofpurchase.

• FOR YOUR SAFETY: Registering your product will allow us to contact you in the unlikely

event a safety notification is required under the Federal Consumer SafetyAct.

Three Year Limited Warranty

DeWALT

will repair, without charge, any defects due to faulty materials or workmanship for

three years from the date ofpurchase. This warranty does not cover part failure due to normal

wear or toolabuse. For further detail of warranty coverage and warranty repair information,

visitwww.dewalt.com or call 1–800–4-

DeWALT

(1–800–433–9258). This warranty does not apply

to accessories or damage caused where repairs have been made or attempted byothers. This

warranty gives you specific legal rights and you may have other rights which vary in certain states

orprovinces.

In addition to the warranty,

DeWALT

tools are covered byour:

1 YEAR FREE SERVICE

DeWALT

will maintain the tool and replace worn parts caused by normal use, for free, any time

during the first year afterpurchase.

2 YEARS FREE SERVICE ON DEWALT BATTERY PACKS

DC9071, DC9091, DC9096, DC9280, DC9360, DC9180,

DCB120, DCB127, DCB201, DCB203, DCB203BT, DCB207

3 YEARS FREE SERVICE ON DEWALT BATTERY PACKS

DCB200, DCB204, DCB204BT, DCB205, DCB606

NOTE: Battery warranty voided if the battery pack is tampered with in anyway.

DeWALT

is not

responsible for any injury caused by tampering and may prosecute warranty fraud to the fullest

extent permitted bylaw.

90 DAY MONEY BACK GUARANTEE

If you are not completely satisfied with the performance of your

DeWALT

Power Tool, Laser, or

Nailer for any reason, you can return it within 90 days from the date of purchase with a receipt for

a full refund – no questionsasked.

LATIN AMERICA: This warranty does not apply to products sold in LatinAmerica. For products

sold in Latin America, see country specific warranty information contained in the packaging, call

the local company or see website for warrantyinformation.

FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are missing,

call 1–800–4-

DeWALT

(1–800–433–9258) for a freereplacement.

Définitions : symboles et termes d'alarmes sécurité

Ces guides d'utilisation utilisent les symboles et termes d'alarmes sécurité suivants pour vous prévenir de

situations dangereuses et de risques de dommages corporels oumatériels.



DANGER: indique une situation dangereuse imminente qui, si elle n’est pas évitée, entraînera la mort

ou des blessuresgraves.



AVERTISSEMENT: indique une situation potentiellement dangereuse qui, si elle n’est pas évitée,

pourrait entraîner la mort ou des blessuresgraves.



ATTENTION: indique une situation potentiellement dangereuse qui, si elle n’est pas évitée, pourrait

entraîner des blessures légères oumodérées.



(Si utilisé sans aucun terme) Indique un message propre à lasécurité.

AVIS : indique une pratique ne posant aucun risque de dommages corporels mais qui par contre, si

rien n’est fait pour l’éviter, pourrait poser des risques de dommages matériels.



AVERTISSEMENT! lire tous les avertissements de

sécurité et toutes lesdirectives. Le non-respect

des avertissements et des directives pourrait se

solder par un choc électrique, un incendie et/ou une

blessuregrave.

AVERTISSEMENT : afin de réduire le risque de

blessures, lire le mode d’emploi del’outil.

Français (traduction de la notice d’instructions originale)

Banco

Hoja

Indicador de escala para cortes longitudinales

Pomo de ajuste

Palanca de bloqueo de riel

Rueda de ajuste de altura de la hoja

Palanca de bloqueo de bisel

Unidad de encendido/apagado

Orificios de montaje

Calibrador de inglete

Unidad del protector de la hoja

Batería

Botón de liberación de la batería

Unidad anti-rebote

Orificio para recolección de polvo

Protector del orificio para recolección de polvo

Placa de garganta

Guía para cortes longitudinales

Seguro de la guía para cortes longitudinales

Guía estrecha para cortes longitudinales/extensión de

apoyo

Llaves para hoja (posición de almacenamiento)

Empujador (Posición de almacenamiento)

Cuchillo separador (aserrado sin traspaso) (Fig. G)

Asa de transporte

Riel de calibrador de inglete

Fig. A

CONSERVER TOUS LES AVERTISSEMENTS ET TOUTES LES

DIRECTIVES POUR UN USAGE ULTÉRIEUR

POUR TOUT COMMENTAIRE, OU TOUTE QUESTION, RELATIF À CET OUTIL OU TOUT AUTRE OUTIL

DeWALT

, COMPOSEZ GRATUITEMENT LE: 1–800–4-

DeWALT

(1–800–433–9258).



AVERTISSEMENT: pour réduire tout risque de dommages corporels, lire le guide

d’utilisation.

Règles de sécurité – Généralités



AVERTISSEMENT: lire ces directives avant toute utilisation du produit. Tout manquement

aux instructions suivantes pose des risques de chocs électriques, d’incendie et/ou de

dommages corporelsgraves.



AVERTISSEMENT: SE CONFORMER AUX NORMES DU CODE EN MATIÈRE DE

CÂBLAGE et connexions électriques pour prévenir tout risque de décharges électriques ou

d’électrocution.

Consignes de sécurité importantes

• POUR RÉDUIRE TOUT RISQUE DE REBONDS ET DOMMAGES CORPORELS, utiliser

systématiquement l’ensemble des composants du dispositif de protection (dispositif de carter de

lame, couteau diviseur et dispositif anti-rebonds) au cours des opérations pour lesquelles ils ont

été conçus, y compris lors de toute coupeintégrale.

• RETIRER TOUTE CLÉ ET TOUT OUTIL DE RÉGLAGE. Vérifier systématiquement que toute clé

ou tout outil de réglage a été retiré de la broche avant de mettre l’outil en marche. Outils, chutes,

ou autres débris pourraient être projetés brusquement, et causer des dommagescorporels.

• MAINTENIR L’AIRE DE TRAVAIL PROPRE. Les établis et locaux encombrés sont propices

auxaccidents.

• NE PAS UTILISER LA MACHINE DANS UN ENVIRONNEMENT DANGEREUX. Ne pas utiliser

d’outils électriques dans des endroits trempés ou humides, ou sous la pluie, pour éviter tout risque

de décharge électrique ou d’électrocution. Maintenir l’atelier bien éclairé pour éviter les chutes ou

la mise en danger des bras, mains oudoigts.

• MAINTENIR LES ENFANTS À L’ÉCART. Pour leur sécurité, tenir les visiteurs à l’écart de l’espace

de travail. Votre atelier est un environnement potentiellementdangereux.

• PROTÉGER L’ATELIER À L’AIDE DE DISPOSITIFS À L’ÉPREUVE DES ENFANTS tels

cadenas et interrupteurs principaux, ou en retirant toute clé de démarrage et le bloc-piles. Le

démarrage non autorisé d’une machine par un enfant ou un visiteur comporte des risques de

dommagescorporels.

• NE PAS FORCER L’OUTIL. Il effectuera un meilleur travail, à un degré de sécurité plus élevé, à la

vitesse pour laquelle il a étéconçu.

• UTILISER L’OUTIL ADÉQUAT. Ne pas forcer l’outil, ou un accessoire, pour effectuer un travail

pour lequel il n’a pas été conçu. Le fait d’utiliser un outil ou un accessoire inadéquat comporte des

risques de dommagescorporels.

• N’EFFECTUEZ AUCUN TRAVAIL HORS DE PORTÉE. Maintenir son équilibre et les pieds bien

ancrés au sol en permanence. Perdre l’équilibre pourrait occasionner des dommages corporels. Ne

pas tenter d’éliminer des matériaux à proximité de la lame de la scie de table alors qu’elletourne.

• PRENDRE SOIN DE SES OUTILS. Conserver les lames bien affûtées et propres pour des

performances optimales et un maximum de sécurité. Suivre toute instruction relative à la

lubrification et au changement d’accessoire. L’utilisation de lames ou machines pauvrement

entretenues comporte des risques de dommages matériels et/oucorporels.

• PORTER LES VÊTEMENTS APPROPRIÉS. Éviter vêtements amples, gants, cravates, bagues,

bracelets ou autres bijoux qui pourraient se prendre dans les pièces mobiles. Il est recommandé de

porter des chaussures antidérapantes. Couvrir ou attacher les cheveuxlongs.

• PORTER SYSTÉMATIQUEMENT DES LUNETTES DE PROTECTION. Utiliser aussi un écran

facial ou un masque antipoussières si la découpe doit en produire beaucoup. Les lunettes

ordinaires ne peuvent que protéger contre les impacts, et ne sont pas des lunettes deprotection.

• ARRIMER LA PIÈCE À TRAVAILLER. Utiliser des colliers de serrage pour maintenir le travail

lorsque c’est utile (particulièrement avec un espacement nul de plaquette de renfort/plaque

de lumière). C’est plus sûr que de le faire manuellement et cela laisse les mains libres pour

utiliserl’outil.

• ARRÊTER LA MACHINE ET DÉCONNECTER LE BLOCPILES avant d’installer ou retirer

tout accessoire, avant tout réglage ou changement de configuration, ou pour effectuer toute

réparation ou tout changement de lieu.

• Ne pas installer ou retirer le bloc-piles avec des mainshumides.

• S'ASSURER QUE L'INTERRUPTEUR EST EN POSITION D'ARRÊT AVANT D'INSÉRER UN

BLOC-PILES. Insérer un bloc-piles dans un outil électrique pose des risques d’accidents.

• UTILISER LES ACCESSOIRES RECOMMANDÉS. N’utiliser que des accessoires recommandés

par le fabricant de votre modèle particulier. Les accessoires convenant à un modèle d’outils

peuvent être dangereux lorsqu’utilisés avec un autre. Consulter le guide d’utilisation pour

connaître les accessoires recommandés. L’utilisation d’accessoires inadéquats comporte des

risques de dommagescorporels.

• Les accessoires magnétiques ne fonctionneront pas avec cettescie.

• NE JAMAIS MONTER OU S’ASSEOIR SUR L’OUTIL. NE JAMAIS L’UTILISER COMME

ESCABEAU. Des dommages corporels graves pourraient en résulter si l’outil basculait ou en cas

de contact involontaire avec l’organe decoupe.

• VÉRIFIER L’ÉTAT DES PIÈCES. Avant toute nouvelle utilisation de l’outil, tout dispositif de

protection, ou autre pièce, endommagé doit être vérifié soigneusement pour déterminer s’il

fonctionnera correctement et remplira la fonction pour laquelle il a été conçu. Vérifier les pièces

mobiles afin de s’assurer qu’elles sont bien alignées et installées, et qu’elles ne resteront pas

coincées. Vérifier également les pièces pour s’assurer qu’il n’y a aucune fêlure ou toute autre

condition susceptible de nuire au bon fonctionnement de l’outil. Tout dispositif de protection,

ou autre pièce, endommagé doit être réparé correctement ou remplacé. Ne pas utiliser un outil

dont l’interrupteur est défectueux. Toute pièce endommagée comporte des risques de dommages

matériels supplémentaires et/oucorporels.

• DIRECTION DE L’ALIMENTATION. Alimenter la pièce à travailler vers la lame, ou l’organe de

coupe, uniquement dans la direction inverse de rotation de ces derniers. Les coupes à gorge ou à

main levée sontinterdites.

• Laisser un espace de sortie suffisant à l’arrière de la scie pour assurer que le matériau ne reste pas

bloqué lors de la coupe. Des tables de support d’ouvrage devraient être placées aux endroits utiles

pour soutenir pleinement lematériau.

• NE JAMAIS LAISSER L’OUTIL FONCTIONNER SANS SUPERVISION. ARRÊTER

SYSTÉMATIQUEMENT L’OUTIL. Attendre l’arrêt complet de l’outil avant de le laisser pour éviter

tout risque de blessuresgraves.

• NE JAMAIS LAISSER DES MATÉRIAUX SUR LA TABLE ALORS QUE LA SCIETOURNE.

• NE PAS UTILISER UN OUTIL ÉLECTRIQUE EN PRÉSENCE DE LIQUIDE OU GAZ

INFLAMMABLE OU EN MILIEU DÉFLAGRANT. Le moteur et les interrupteurs de ces outils

pourraient provoquer des étincelles et unincendie.

• RESTER PRUDENT. RESTER VIGILANT ET FAIRE PREUVE DE BON SENS. NE PAS UTILISER

LA MACHINE EN CAS DE FATIGUE OU SOUS L’INFLUENCE DE DROGUES, D’ALCOOL

OU DE MÉDICAMENTS. Tout moment d’inattention pendant l’utilisation d’un outil électrique

comporte des risques de blessuregrave.

• NE PAS LAISSER LA FAMILIARITÉ AVEC L’OUTIL gagnée par l’utilisation fréquente de

la scie REMPLACER LES CONSIGNES DE SÉCURITÉ. Se rappeler qu’il suffit d’une fraction

de seconde d’inattention pour causer des dommages corporels graves. Prendre des précautions

supplémentaires et rester alerte lors de coupes répétitives. Arrêter la scie fréquemment pour

éliminer la poussière et vérifier les réglages pour réduire lamonotonie.

Règles de sécurité additionnelles relatives aux scies de table

• ÉVITER LES POSITIONS INSTABLES, qui pourraient provoquer une chute soudaine et risquer

de mettre la lame en contact avec lamain.

• Ne pas tenter d’éliminer des matériaux à proximité de la lame de la scie de table alors

qu’elletourne.

• NE JAMAIS UTILISER LA MAIN POUR MAINTENIR LA PIÈCE DE TRAVAIL, que ce soit

derrière ou autour de l’organe decoupe.

• ÉLOIGNER LES BRAS, MAINS ET DOIGTS de la lame pour prévenir tout dommage

corporelgrave.

• UTILISER UN POUSSOIR DE FIN DE PASSE APPROPRIÉ À L’APPLICATION EN COURS

POUR POUSSER LA PIÈCE VERS LA SCIE. Un poussoir de fin de passe est un morceau de bois

ou de plastique, souvent fait maison, qui devrait être utilisé chaque fois que la taille ou la forme

de la pièce à travailler obligerait les mains de s’approcher à moins de 152mm (6po) de lalame.

• UTILISER SUPPORTS, DISPOSITIFS DE FIXATION OU PEIGNES POUR GUIDER ET

CONTRÔLER LA PIÈCE À TRAVAILLER. Les accessoires recommandés pour cet outil sont

vendus séparément chez les distributeurs locaux ou dans les centres de réparation agréés. Des

instructions pour créer: poussoir de fin de passe, guide longitudinal auxiliaire étroit, bloc-poussoir

et peignes, sont incluses dans cemanuel.

• N’EFFECTUER AUCUNE COUPE LONGITUDINALE, TRANSVERSALE OU TOUTE AUTRE

OPÉRATION À LAMAIN.

• NE JAMAIS passer les mains autour ou par-dessus la lame alors qu’elletourne.

• STABILITÉ. S’assurer que la scie de table est fermement arrimée à une surface stable, et

complètement immobilisée avant touteutilisation.

• LA SCIE DE TABLE DEVRAIT ÊTRE INSTALLÉE UNIQUEMENT SUR UNE SURFACE PLANE

ET STABLE. L’aire de travail devrait être exempte de toute obstruction et de tout danger de chute.

Aucun matériau ou outil ne devrait reposer sur lascie.

• NE JAMAIS DÉCOUPER DE MÉTAUX, CIMENT OU MAÇONNERIE. Certains matériaux

synthétiques doivent être découpés avec des scies de table en suivant des instructions

particulières. Suivre systématiquement les recommandations du fabricant pour prévenir tout

risque de dommages corporels etmatériels.

• Ne pas installer de lame diamant pour maçonnerie sur la scie de table et tenter de l’utiliser

comme une scie àeau.

• UNE PLAQUE DE LUMIÈRE APPROPRIÉE DOIT ÊTRE SYSTÉMATIQUEMENT

VERROUILLÉE EN PLACE pour réduire tout risque d’éjection de pièce et de dommagescorporels.

• UTILISER UNE LAME DE SCIE CONÇUE SPÉCIALEMENT POUR L’OPÉRATION DÉSIRÉE. La

rotation de la lame doit se faire vers l’avant de la scie. Serrer fermement l’écrou d’arbre de lame.

Avant toute utilisation, vérifier que la lame ne comporte aucune fente, ou dents manquantes. Ne

pas utiliser de lame endommagée ouémoussée.

• NE JAMAIS TENTER DE LIBÉRER UNE LAME BLOQUÉE AVANT D’AVOIR ARRÊTÉ LA SCIE

ET RETIRÉ LE BLOCPILES. Si un morceau ou un rebut restait coincé dans le dispositif du carter

de lame, arrêter la scie, et attendre l’arrêt complet de la lame, avant de soulever le dispositif de

carter de lame et de retirer le morceaucoincé.

• NE JAMAIS REMETTRE LA MACHINE EN MARCHE alors que la pièce à travailler se trouve

contre la lame pour réduire tout risque d’expulsion de la pièce et de dommagescorporels.

• NE JAMAIS LAISSER AUCUNE PARTIE DU CORPS ENTRER DANS LE SILLAGE DE LA

LAME, car il y a risques de dommages corporels. Se placer d’un côté ou de l’autre de lalame.

• NE JAMAIS EFFECTUER DE MISE EN PLACE, MONTAGE OU CONFIGURATION sur

la table/l’aire de travail alors que la machine tourne. Un dérapage soudain pourrait

causer un contact involontaire entre la lame et les mains. Cela pose des risques de dommages

corporelsgraves.

• NE JAMAIS EFFECTUER DE RÉGLAGES ALORS QUE LA SCIE TOURNE, comme le

repositionnement ou retrait du guide, le réglage du verrouillage de biseau ou le réglage de la

hauteur delame.

• NETTOYER LA TABLE/L’ESPACE DE TRAVAIL AVANT DE LAISSER LA MACHINE. Verrouiller

l’interrupteur en position «OFF» (arrêt) et retirer le bloc-piles pour prévenir toute utilisation

nonautorisée.

• Verrouiller SYSTÉMATIQUEMENT le guide ou le réglage de biseau avant toutecoupe.

• NE PAS laisser une longue planche (ou toute autre pièce similaire) non soutenue, car

l’effet de ressort de la planche pourrait la faire glisser de la table et causer perte de

contrôle du matériel et dommages corporels. Fournir un support adéquat à la pièce à

travailler compte tenu de sa taille et du type d’opération à effectuer. Maintenir fermement la pièce

à travailler contre le guide et à plat sur la surface de latable.

• Si la scie fait un bruit inhabituel ou vibre excessivement, arrêter aussitôt toute opération, arrêter

l’outil et retirer son bloc-piles jusqu’à ce que le problème ait été identifié et corrigé. Si le problème

persiste, contacter un centre de réparation d’usine

DeWALT

, un centre de réparation agréé

DeWALT

ou tout autre personnel de réparationqualifié.

• NE PAS UTILISER CETTE MACHINE tant qu’elle n’est pas complètement assemblée et installée,

conformément aux instructions données. Une machine incorrectement assemblée pose des

risques de dommages corporelsgraves.

• NE JAMAIS tenter de couper un amas de morceaux de matériaux, car il y a risques de perte de

contrôle ou rebonds. Soutenir soigneusement toutmatériau.

• NE PAS ENTREPOSER CET OUTIL AVEC SON BLOCPILES INSTALLÉ. Envisager toute

éventualité pour prévenir la mise en marche accidentelle de lascie.

• NE PAS TRANSPORTER CET OUTIL AVEC SON BLOCPILESINSTALLÉ.

• DES INFORMATIONS COMPLÉMENTAIRES sur la sécurité et l’utilisation correcte des

outils électriques (ex.: vidéo sécurité) sont à votre disposition auprès du Power Tool Institute

(l’Institut des Outils Électriques), 1300 Sumner avenue, Cleveland, OH 44115-2851 (www.

powertoolinstitute. com). Des informations sont aussi à votre disposition auprès du National

Safety Council (Conseil National de la Sécurité), 1121 Spring Lake Drive, Itasca, IL 60143-3201. Se

reporter aux normes OSHA 1910.213 du Département du TravailAméricain.

Terminologie : la terminologie suivante sera utilisée dans ce

manuel et nous vous recommandons de vous familiariser avec

ses termes.

• Coupe intégrale: la pièce à travailler est découpée de bout enbout.

• Coupe partielle: la pièce à travailler est découpéepartiellement.

• Poussoir de fin de passe: un morceau de bois ou de plastique, fait maison en général, et utilisé

pour pousser une petite pièce vers la scie tout en protégeant de la lame les mains de l’utilisateur.

• Rebonds: ils se produisent lorsque la lame de la scie reste coincée dans la ligne de coupe et

repousse violemment la pièce à travailler vers l’utilisateur. Des rebonds encore plus graves

et dangereux se produiront lorsque la scie sera utilisée sans ses dispositifs de protection ou

son couteau diviseur. Les matériaux en contact avec le bord externe de la lame seront éjectés

violemment et de façon imprévisible sur l’utilisateur.

• À main levée: une coupe sans l’utilisation d’un guide d’onglet ou d’un guide longitudinal ou de

tout autre moyen de guider ou maintenir la pièce à travailler autre que les mains de l’utilisateur.



AVERTISSEMENT: ne jamais effectuer de coupe à main levée avec cettescie.

• Coupe en plongée: toute coupe où la pièce à travailler est soit abaissée sur la lame alors

que la pièce est contrôlée manuellement par l’utilisateur soit lorsque la pièce est soutenue

manuellement par l’utilisateur sur la surface de table et la lame élevée au travers de lapièce.



AVERTISSEMENT: ne jamais effectuer de coupe en plongée avec cettescie.

• Coupe double: inverser le matériau pour le recouper lorsque la scie est incapable de le faire en

une seulepasse.



AVERTISSEMENT: ne jamais effectuer de coupe double avec cettescie.

• Sortie: l’espace à l’arrière de la scie doit permettre au matériau de sortir complètement de

lacoupe.

• Rainurage: utilisation d’une tête à rainurer ou de tout autre type d’organe de coupe à profiler

pour faire des rainures ou des engravuresdécoratives.



AVERTISSEMENT: ne pas installer de tête à rainurer ou d’organe de coupe à profiler sur

cettescie.

Dispositif de carter de lame, dispositif anti-rebonds et couteau

diviseur

Votre scie de table est équipée d’un dispositif de carter de lame avec couteau séparateur et d’un

dispositif anti-rebonds pour couvrir la lame et réduire les risques de contact accidentel avec la

lame. Un couteau diviseur est aussi fourni pour les coupes non intégrales. Le couteau diviseur et le

couteau séparateur sont des plaques à positionner derrière la lame de scie et qui rentrent dans la

ligne de coupe. Deux taquets anti-rebonds situés de chaque côté du couteau séparateur permettent

au bois d’être traversé par la lame dans la direction de coupe en réduisant les possibilités de rejet

en arrière du matériau vers l’utilisateur. Cela aide à prévenir les rebonds causés par le blocage ou

grippage du matériau découpé à l’arrière de la lame de scie. Les dispositifs de carter de lame

et anti-rebonds peuvent être utilisés uniquement pour faire des coupes traversantes,

coupant intégralement le bois. Pour effectuer des feuillures, rainures, tenons, assemblages

à recouvrement ou autres coupes non intégrales, les dispositifs de carter de lame et anti-

rebonds doivent être retirés et le couteau diviseur doit être installé.

Utiliser systématiquement l’ensemble des composants du dispositif de protection (dispositif de carter

de lame, couteau diviseur et dispositif anti-rebonds) au cours des opérations pour lesquelles ils ont été

conçus, y compris lors de toute coupe intégrale. Si l’on choisit de ne pas utiliser l’un de ces composants

pour une application particulière, prendre des précautions supplémentaires pour garder le contrôle

de la pièce: utiliser des poussoirs de fin de passe, faire attention à la position des mains par rapport

à la lame; utiliser une protection oculaire ainsi que tout moyen d’éviter les rebonds; et respecter les

avertissements contenus dans ce manuel et sur la scie elle-même. Réinstaller les systèmes de

protection dès que l’on reprend des coupes intégrales. Maintenir les dispositifs de protection en

bon état demarche.

Création d’un poussoir de fin de passe (troisième de couverture)

• Pour utiliser la scie de table en toute sécurité, il est recommandé d’utiliser un poussoir de fin de

passe chaque fois que la taille ou la forme de la pièce à travailler oblige les mains à s’approcher à

moins de 152mm (6po) de la lame. Un poussoir de fin de passe est inclus avec cettescie.

• Il se pourra que des poussoirs de fin de passe supplémentaires soient nécessaires pour

accommoder des matériaux de différentes épaisseurs. Des plans de poussoirs de fin de passe sont

inclus en fin de ce guide d’utilisation. Les poussoirs de fin de passe devraient être en bois massif,

contreplaqué, plastique ou autres matériaux, à la fois résistants et tendres. Il est recommandé de

lui donner une longueur de 400mm (15,7po) avec une encoche qui s’encastre dans le bord de la

pièce à travailler pour éviter qu’il ne glisse. Il est bon d’avoir plusieurs poussoirs de fin de passe de

la même longueur, 400mm (15,7po), avec des tailles d’encoches différentes pour accommoder

différentes épaisseurs depièces.

Rebonds

Les rebonds peuvent causer des dommages corporels graves. Un rebond se produit lorsqu’une portion

de la pièce à travailler reste coincée entre la lame et le guide longitudinal, ou tout autre objet fixe,

et projette la pièce hors de la table vers l’utilisateur. Les rebonds peuvent être évités en prenant les

mesuressuivantes.

Comment les éviter et vous protéger de dommages corporels possibles:

a ) Utiliser un carter de lame avec un couteau séparateur, ou un couteau diviseur,

chaque fois quepossible.

b ) S’assurer que le guide longitudinal est bien parallèle à lalame.

c ) Ne pas découper longitudinalement en appliquant la force d’avance à la section de

la pièce à travailler qui est destinée à devenir la chute. Pour une coupe longitudinale,

la force d’avance doit systématiquement être appliquée entre la lame et le guide. Utiliser un

bâtonnet pour pousser les pièces étroites de 152mm (6po) de) large oumoins.

d ) Maintenir en place, et en bon état de marche, les dispositifs de carter de lame et

de rebonds et le couteau diviseur. Si le dispositif anti-rebonds n’est pas opérationnel,

rapporter votre appareil dans le centre de réparation agréé

DeWALT

le plus proche. Le couteau

séparateur et le couteau diviseur doivent être alignés avec la lame de scie, et le dispositif anti-

rebonds doit pouvoir arrêter les rebonds dès leur origine. Vérifier leur fonctionnement avant

de faire des coupes longitudinales en poussant le bois sous le dispositif anti-rebonds. Les

dents doivent empêcher le bois d’être tiré vers l’avant de lascie.

e ) Les plastiques et matériaux composites (comme les planchers lamellaires) peuvent

être découpés avec cette scie. Ces matériaux peuvent avoir une surface dure ou glissante

qui pourra limiter l’efficacité du dispositif anti-rebonds. Lors de la coupe de ces matériaux,

suivre tout particulièrement les instructions relatives à la coupelongitudinale.

f ) Utiliser les dispositifs de carter de lame et anti-rebonds et le couteau diviseur

pour chaque opération pour laquelle ils peuvent être utilisés, y compris toutes les

coupesintégrales.

g ) Pousser la pièce au-delà de la lame de scie avant de larelâcher.

h ) NE JAMAIS découper longitudinalement une pièce gondolée ou déformée, ou sans

bord droit pour la guider le long duguide.

i ) NE JAMAIS scier une pièce trop large pour êtrecontrôlée.

j ) NE JAMAIS utiliser le guide en tant que guide ou butée de longueur pour faire des

coupestransversales.

k ) NE JAMAIS scier une pièce comportant: nœuds décollés, défauts, clous ou autres

objetsétrangers.

l ) NE JAMAIS couper longitudinalement une pièce de moins de 254mm (10po).

m ) NE JAMAIS utiliser de lame émoussée, la remplacer ou la faireaffûter.



AVERTISSEMENT: PORTER SYSTÉMATIQUEMENT des lunettes de protection.

Les lunettes courantes NE sont PAS des lunettes de protection. Utiliser aussi un écran

facial ou un masque antipoussières si la découpe doit en produire beaucoup. PORTER

SYSTÉMATIQUEMENT UN ÉQUIPEMENT DE SÉCURITÉ HOMOLOGUÉ:

• Protection oculaire ANSI Z87.1 (CAN/CSA Z94.3);

• Protection auditive ANSI S12.6 (S3.19);

• Protection des voies respiratoires NIOSH/OSHA/MSHA.



AVERTISSEMENT: certains outils électriques, tels que les sableuses, les scies, les meules,

les perceuses ou autres outils de construction peuvent produire des poussières contenant

des produits chimiques reconnus par l’état californien pour causer cancers, malformations

congénitales ou être nocifs au système reproducteur. Parmi ces produits chimiques, on

retrouve:

• le plomb dans les peintures à base de plomb;

• la silice cristallisée dans les briques et le ciment ou autres articles de maçonnerie; et

• l’arsenic et le chrome dans le bois ayant subi un traitementchimique.

Le risque associé à de telles expositions varie selon la fréquence à laquelle on effectue ces travaux.

Pour réduire toute exposition à ces produits, travailler dans un endroit bien aéré, en utilisant le

matériel de sécurité conforme, tel un masque anti-poussières spécialement conçu pour filtrer les

particulesmicroscopiques.

• Limiter toute exposition prolongée aux poussières provenant du ponçage, sciage,

meulage, perçage ou toute autre activité de construction. Porter des vêtements de

protection et nettoyer à l’eau savonneuse les parties du corps exposées. Le fait de laisser

la poussière pénétrer dans la bouche, les yeux ou la peau peut favoriser l’absorption de produits

chimiquesdangereux.



AVERTISSEMENT: cet outil peut produire et/ou répandre de la poussière susceptible de

causer des dommages sérieux et permanents au système respiratoire ou d’autres dommages

corporels. Lors de l’exposition aux poussières, utiliser systématiquement un appareil de

protection des voies respiratoires homologué par NIOSH ou OSHA. Diriger les particules à

l’opposé du visage et ducorps.

AVIS: suite à certaines conditions d’utilisation, comme l’utilisation longue durée dans des

milieux à humidité moindre, la coupe de certains matériaux comme le vinyle, des charges

électrostatiques pourront s’accumuler sur les portions métalliques de la scie. Toucher ces

parties métalliques pourra libérer ces charges électrostatiques et causer une décharge

électrique brève et légère, mais sans danger. Cependant, en cas de doutes à ce propos,

rapporter la scie dans un centre de réparation

DeWALT

pour une inspection gratuite et vérifier

que la scie n’est affectée d’aucun dysfonctionnementélectrique.

L’étiquette apposée sur votre outil peut inclure les symbolessuivants. Les symboles et leur définition

sont indiqués ci-après:

......................... volts

Hz ....................... hertz

min ..................... minutes

or DC ...... courant continu

...................... fabrication classe I (mis à la terre)

…/min .............. par minute

BPM .................... battements par minute

IPM ..................... impacts par minute

RPM .................... revolutions per minute

sfpm ................... pieds linéaires par minute (plpm)

SPM (FPM) ......... fréquence par minute

A ......................... ampères

W ........................ watts

or AC ........... courant alternatif

or AC/DC .... courant alternatif ou continu

...................... fabrication classe I (double isolation)

no ....................... vitesse à vide

n ......................... vitesse nominale

...................... borne de terre

...................... symbole d’avertissement

..................... radiation visible

..................... protection respiratoire

.....................protection oculaire

.....................protection auditive

BLOCS-PILES ET CHARGEURS

Le bloc-piles n’est pas totalement chargé d’usine. Avant d’utiliser le bloc-piles et le chargeur,

lire les consignes de sécurité ci-après puis suivre la procédure de chargement indiquée. Pour

commander un bloc-piles de rechange, s’assurer d’en inclure le numéro de catalogue et

latension.

Cet outil fonctionne avec un chargeur

DeWALT

. S’assurer de bien lire toutes les consignes de

sécurité avant toute utilisation du chargeur. Consulter le tableau en fin de manuel pour connaître

les compatibilités entre chargeurs et blocs-piles.

Consignes importantes de sécurité les blocs-piles



AVERTISSEMENT : lire toutes les instructions et toutes les consignes de sécurité

propres au bloc-piles, au chargeur et à l’outil électrique. Tout manquement aux

avertissements et instructions pose des risques de décharges électriques, d’incendie

et/ou de blessures graves.

• Ne pas recharger ou utiliser un bloc-piles en milieu déflagrant, en présence, par

exemple, de poussières, gaz ou liquides inflammables. Le fait d’insérer ou retirer un bloc-

piles de son chargeur pourrait causer l’inflammation de poussières ou d’émanations.

• NE JAMAIS forcer l’insertion d’un bloc-piles dans un chargeur. NE modifier un bloc-piles

d’AUCUNE façon pour le faire rentrer dans un chargeur incompatible, car il pourrait se

briser et causer des dommages corporels graves. Consulter le tableau en dernière page de

ce manuel pour connaître les compatibilités entre chargeurs et blocs-piles.

• Recharger les blocs-piles exclusivement dans des chargeurs

DeWALT

• NE PAS éclabousser le bloc-piles ou l’immerger dans l’eau ou dans tout autreliquide.

• Ne pas entreposer ou utiliser l’appareil et le bloc-piles en présence de températures

ambiantes pouvant excéder 40°C (104°F) (comme dans des hangars ou des bâtiments

métalliques l’été). Pour préserver leur durée de vie, entreposer les blocs-piles dans un endroit

frais etsec.

REMARQUE: ne pas mettre un bloc-piles dans un outil dont la gâchette est verrouillée

en position de marche. Ne jamais bloquer l’interrupteur en position deMARCHE.

• Ne pas incinérer le bloc-piles même s’il est sévèrement endommagé ou complètement

usagé, car il pourrait exploser et causer un incendie. Pendant l’incinération des blocs-piles

au lithium-ion, des vapeurs et matières toxiques sontdégagées.

• En cas de contact du liquide de la pile avec la peau, rincer immédiatement au savon

doux et à l’eau. En cas de contact oculaire, rincer l’œil ouvert à l’eau claire une quinzaine de

minutes ou jusqu’à ce que l’irritation cesse. Si des soins médicaux s’avéraient nécessaires, noter

que l’électrolyte de la pile est composé d’un mélange de carbonates organiques liquides et de sels

delithium.

• Le contenu des cellules d’une pile ouverte peut causer une irritation respiratoire. En cas

d’inhalation, exposer l’individu à l’air libre. Si les symptômes persistent, consulter unmédecin.



AVERTISSEMENT: risques de brûlure. Le liquide de la pile peut s’enflammer s’il est exposé à

des étincelles ou à uneflamme.



AVERTISSEMENT: risques d’incendie. Ne jamais tenter d’ouvrir le bloc-piles pour quelque

raison que ce soit. Si le boîtier du bloc-piles est fissuré ou endommagé, ne pas l’insérer dans

un chargeur. Ne pas écraser, laisser tomber, ou endommager les blocs-piles. Ne pas utiliser

un bloc-piles ou un chargeur qui a reçu un choc violent, ou si l’appareil est tombé, a été

écrasé ou endommagé de quelque façon que ce soit (p. ex. percé par un clou, frappé d’un

coup de marteau, piétiné). Les blocs-piles endommagés doivent être renvoyés à un centre de

réparation pour y êtrerecyclés.

Transport



AVERTISSEMENT: risques d’incendie. Au moment de ranger ou transporter le bloc-

piles, veiller à protéger ses bornes à découvert de tout objet métallique. Par exemple,

éviter de placer le bloc-piles dans un tablier, une poche, une boîte à outils ou un tiroir, etc.

contenant des objets tels que clous, vis, clés, etc. Le fait de transporter des blocs-piles

comporte des risques d’incendie, car les bornes des piles pourraient entrer, par

inadvertance, en contact avec des objets conducteurs, tels que: clés, pièces de

monnaie, outils ou autres. La réglementation sur les produits dangereux (Hazardous

Material Regulations) du département américain des transports interdit, en fait, le transport

des blocs-piles dans les commerces ou dans les avions dans les bagages de cabine, À MOINS

qu’ils ne soient correctement protégés de tout court-circuit. Aussi lors du transport individuel

de blocs-piles, s’assurer que leurs bornes sont bien protégées et isolées de tout matériau

pouvant entrer en contact avec elles et provoquer un court-circuit.

Expédition du bloc-piles

DeWALT

FLEXVOLT

Le bloc-piles D

WALT FLEXVOLT

possède deux modes: Utilisation et Expédition.

Mode Utilisation: lorsque le bloc-piles FLEXVOLT

est par lui-même ou dans un produit

WALT 20v max*, il fonctionnera comme un bloc-piles de 20v max*. Lorsque le bloc-piles

FLEXVOLT

est dans un produit de 60v max* ou 120v max* (deux blocs-piles de 60v max*), il

fonctionnera comme un bloc-piles de 60v max*..

Mode Expédition: lorsque le capuchon est inséré sur le bloc-

piles FLEXVOLT

, le bloc-piles est en mode Expédition. Les

modules de cellules sont électriquement déconnectés du bloc

le faisant correspondre à trois blocs-piles d’un wattheure (Wh)

inférieur comparé à un bloc-piles de wattheure élevé. Ce passage

à trois blocs-piles à un wattheure inférieur peut permettre au bloc-piles d’être exempté de suivre

certaines directives d’expédition imposées sur les blocs-piles de wattheuresupérieur.

L’étiquette du bloc-piles donne deux estimations de wattheures (se reporter à l’exemple). Selon

comment le bloc-piles est expédié, l’estimation appropriée de wattheure doit être utilisée pour

déterminer les modalités d’expédition lui correspondant. Si le capuchon d’expédition est utilisé,

le bloc-piles sera considéré comme 3 blocs-piles au wattheure indiqué pour «Expédition». S’il est

expédié sans le capuchon ou dans un outil, le bloc-piles sera considéré comme un seul bloc-piles

au wattheure indiqué à côté de «Utilisation».

USE: 120 Wh Shipping: 3 x 40 Wh

exemple d’étiquetage d’utilisation et d’expédition

Le Wh de transport indique 3 x 40 Wh, ce qui correspond à 3 blocs-piles de 40 wattheures

chacun. L’utilisation du wattheure indique 120 wattheures (sous-entendu 1 bloc-piles).

Témoin de Charge du Bloc-Piles (Fig. B)

Certains blocs-piles

DeWALT

possèdent un témoin de charge qui consiste en trois voyants Del

verts indiquant le niveau de charge du bloc-piles.

Le témoin de charge indique approximativement le niveau de charge restant dans le bloc-piles

en fonction des voyants suivants:

Chargé de 75 à 100%

Chargé de 51 à 74%

Chargé de < 50%

Le bloc-piles doit être rechargé

Pour activer le témoin de charge, maintenez appuyé le bouton du témoin de charge

26

. Une

combinaison des trois voyants Del verts s’allumera indiquant le niveau de charge. Lorsque le

niveau de charge du bloc-pile atteint la limite minimale d’utilisation, le témoin de charge reste

éteint et le bloc-piles doit êtrerechargé.

Fig. B

REMARQUE: le témoin de charge ne fait qu’indiquer le niveau de charge du bloc-piles. Il ne

donne aucune indication quant au fonctionnement de l’outil. Son propre fonctionnement

pourra aussi varier en fonction des composants produit, de la température et de l’application

d’utilisation.

Pour plus d’informations quant au témoin de charge du bloc-piles, veuillez appeler le

1-800-4-

DeWALT

(1-800-433-9258) ou vous rendre sur notre site www.dewalt.com.

Le sceau SRPRC®

Le sceau SRPRC® (Société de recyclage des piles rechargeables du Canada)

apposé sur une pile au nickel-cadmium, à hydrure métallique de nickel ou

au lithium-ion (ou un bloc-piles) indique que les coûts de recyclage de ces

derniers en fin d’utilisation ont déjà été réglés par

DeWALT

. Dans certaines

régions, la mise au rebut ou aux ordures municipales des piles au nickel-

cadmium, à l’hydrure métallique de nickel ou au lithium-ion, est illégale; le programme de

l’Appel à Recycler® constitue donc une solution pratique etécologique.

Appel à Recycler Canada, Inc., en collaboration avec

DeWALT

et d’autres utilisateurs de piles, a mis

sur pied de programme aux États-Unis et au Canada pour faciliter la collecte des piles au nickel-

cadmium, à l’hydrure métallique de nickel ou au lithium-ion usagées. Aidez-nous à protéger

l’environnement et à conserver nos ressources naturelles en renvoyant les piles au nickel-

cadmium, à l’hydrure métallique de nickel ou au lithium-ion usagées à un centre de réparation

autorisé

DeWALT

ou chez votre détaillant afin qu’elles y soient recyclées. On peut en outre se

renseigner auprès d’un centre de recyclage local pour connaître d’autres sites lesacceptant.

SRPRC® est une marque déposée de l’Appel à Recycler Canada,Inc.

Directives de sécurité importantes propres à tous les chargeurs de

piles



AVERTISSEMENT : lire toutes les instructions et toutes les consignes de sécurité

propres au bloc-piles, au chargeur et à l’outil électrique. Tout manquement aux

avertissements et instructions pose des risques de décharges électriques, d’incendie

et/ou de blessures graves.

• NE PAS tenter de charger de bloc-piles avec des chargeurs autres que ceux décrits

dans ce manuel. Le chargeur et son bloc-piles ont été conçus tout spécialement pour

fonctionnerensemble.

• Ces chargeurs n’ont pas été conçus pour une utilisation autre que recharger les blocs-

piles rechargeables

DeWALT

. Toute autre utilisation comporte des risques d’incendie, de chocs

électriques ou d’électrocution.

• Protéger le chargeur de la pluie ou de laneige.

• Tirer sur la fiche plutôt que sur le cordon pour débrancher le chargeur. Cela permet de

réduire les risques d’endommager la fiche ou le cordon d’alimentation.

• S’assurer que le cordon est protégé de manière à ce que personne ne marche ni ne

trébuche dessus, ou à ce qu’il ne soit ni endommagé ni soumis à aucunetension.

• N’utiliser une rallonge qu’en cas de nécessité absolue. L’utilisation d’une rallonge

inadéquate comporte des risques d’incendie, de chocs électriques ou d’électrocution.

• Pour utiliser un chargeur à l’extérieur, le placer dans un endroit sec et utiliser une

rallonge conçue pour l’extérieur. L’utilisation d’une rallonge conçue pour l’extérieur réduit les

risques de chocsélectriques.

• Pour la sécurité de l’utilisateur, utiliser une rallonge de calibre adéquat (AWG,

American Wire Gauge [calibrage américain normalisé des fils électriques]). Plus le calibre

est petit, et plus sa capacité est grande. Un calibre16, par exemple, a une capacité supérieure

à un calibre18. L’usage d’une rallonge de calibre insuffisant causera une chute de tension qui

entraînera perte de puissance et surchauffe. Si plus d’une rallonge est utilisée pour obtenir une

certaine longueur, s’assurer que chaque rallonge présente au moins le calibre de fil minimum.

Le tableau ci-dessous illustre les calibres à utiliser selon la longueur de rallonge et l’intensité

nominale indiquée sur la plaque signalétique. En cas de doute, utiliser le calibre suivant. Plus le

calibre est petit, plus la rallonge peut supporter decourant.

Calibre minimum pour les cordons d'alimentation

Volts

Longueur totale du cordon

d'alimentation en mètre (pieds)

120 V 7,6 (25) 15,2 (50) 30,5 (100) 45,7 (150)

240 V 15,2 (50) 30,5 (100) 61,0 (200) 91,4 (300)

Ampères

AWG

Plus que Pas plus

que

0 6 18 16 16 14

6 10 18 16 14 12

10 12 16 16 14 12

12 16 14 12 Non recommandé

• Ne poser aucun objet sur le chargeur. Ne pas mettre le chargeur sur une surface molle

qui pourrait en bloquer la ventilation et provoquer une surchauffe interne. Éloigner le

chargeur de toute source de chaleur. Le chargeur dispose d’orifices d’aération sur le dessus et le

dessous duboîtier.

• Ne pas le faire fonctionner avec un cordon d’alimentation ou une ficheendommagée.

• Ne pas utiliser le chargeur s’il a reçu un coup, fait une chute ou a été endommagé de

quelque façon que ce soit. Le ramener dans un centre de réparationagréé.

• Ne pas démonter le chargeur. Pour tout service ou réparation, le rapporter dans un

centre de réparation agréé. Le fait de le réassembler de façon incorrecte comporte des risques

de chocs électriques, d’électrocution et d’incendie.

• Débrancher le chargeur du secteur avant tout entretien. Cela réduira tout risque de

chocs électriques. Le fait de retirer le bloc-piles ne réduira pas cesrisques.

• NE JAMAIS tenter de connecter 2 chargeursensemble.

• Le chargeur a été conçu pour être alimenté en courant électrique domestique standard

de 120 volts. Ne pas tenter de l’utiliser avec toute autre tension. Cela ne s’applique pas

aux chargeurs de postesmobiles.



AVERTISSEMENT: risques de chocs électriques. Ne laisser aucun liquide pénétrer dans le

chargeur, des chocs électriques pourraient enrésulter.



AVERTISSEMENT: risques de brûlure. Ne submerger le bloc-piles dans aucun liquide et le

protéger de toute infiltration de liquide. Ne jamais tenter d’ouvrir le bloc-piles pour quelque

raison que ce soit. Si le boîtier plastique du bloc-piles est brisé ou fissuré, le retourner dans un

centre de réparation pour y êtrerecyclé.



ATTENTION: risques de brûlure. Pour réduire tout risque de dommages corporels, ne

recharger que des blocs-piles rechargeables

DeWALT

. Tout autre type de piles pourrait

exploser et causer des dommages corporels etmatériels.



ATTENTION : après utilisation, ranger le bloc-piles à l'écart de tout objet métallique

comme trombones, pièces de monnaie, clés, clous, vis ou autres petits objets

susceptibles de conduire l’électricité entre les bornes. Court-circuiter les bornes

comporte des risques de brûlures ou d’incendie.

AVIS: sous certaines conditions, lorsque le chargeur est connecté au bloc d’alimentation, des

matériaux étrangers pourraient court-circuiter le chargeur. Les corps étrangers conducteurs

tels que (mais pas limité à) poussières de rectification, débris métalliques, laine d’acier, feuilles

d’aluminium, ou toute accumulation de particules métalliques doivent être maintenus à

distance des orifices du chargeur. Débrancher systématiquement le chargeur lorsque le bloc-

piles n’y est pas inséré. Débrancher systématiquement le chargeur avant toutentretien.

Chargement du bloc-piles (Fig. C)

1. Branchez le chargeur dans la prise appropriée avant d’y insérer le bloc-piles.

Fig. C

2. Insérer le bloc-piles

12

dans le chargeur, en vous assurant qu’il y est correctement calé. Le

voyant rouge (charge) clignotera de façon continue indiquant que le cycle de chargement

acommencé.

3. En fin de charge, le voyant rouge restera ALLUMÉ de façon continue. Le bloc-piles est alors

complètement rechargé et peut être utilisé ou laissé dans le chargeur. Pour retirer le bloc-

piles du chargeur, appuyez sur le bouton de libération du bloc-piles

13

sur le bloc-piles.

REMARQUE: pour assurer des performances optimales et une durée de vie maximale des blocs-

piles au lithium-ion, recharger pleinement le bloc-piles avant toute utilisationinitiale.

Utilisation du chargeur

Reportez-vous aux indications du tableau ci-dessous pour consulter le statut de charge

dubloc-piles.

DCB101

Bloc-piles en Cours de Chargement

Bloc-piles Chargé

Suspension de Charge Contre le Chaud/Froid

Bloc-Pile ou Chargeur Défectueux

DCB107, DCB112, DCB113, DCB115, DCB118

Bloc-piles en Cours de Chargement

Bloc-piles Chargé

Suspension de Charge Contre le Chaud/Froid*

* DCB107, DCB112, DCB113, DCB115, DCB118: le voyant rouge ne cessera de clignoter,

mais un voyant jaune restera allumé pendant cette opération. Lorsque le bloc-piles aura repris

une température appropriée, le voyant jaune s’éteindra et le chargeur reprendra sa procédure

decharge.

Le chargeur ne pourront recharger des blocs-piles défectueux. Le chargeur indiquera qu’un bloc-

piles est défectueux en refusant de s’allumer ou en affichant bloc-piles ou chargeurdéfectueux.

REMARQUE: cela pourra aussi indiquer un problème avec lechargeur.

Si le problème provient du chargeur, faites vérifier le chargeur et le bloc-piles chez un centre de

réparationagréé.

Fonction de suspension de charge contre le chaud/froid

Lorsque le chargeur détecte un bloc-piles trop chaud ou trop froid, il démarre automatiquement

la fonction de suspension de charge contre le chaud, suspendant le chargement jusqu’à

ce que le bloc-piles ait repris une température appropriée. Le chargeur ensuite se remettra

automatiquement en mode de chargement. Cette caractéristique assure aux blocs-piles une

durée de viemaximale.

Un bloc-piles froid se rechargera moins vite qu’un bloc-piles chaud. Le bloc-piles se rechargera à

ce rythme plus lent tout au cours du cycle de charge et ne retournera pas à sa vitesse maximale

de charge même s’il venait à seréchauffer.

Le chargeur DCB118 est équipé d’un ventilateur interne destiné à refroidir le bloc-piles. Le

ventilateur se mettra automatiquement en marche chaque fois que le bloc-piles aura besoin de

serefroidir.

N’utilisez jamais le chargeur si le ventilateur ne fonctionne pas correctement ou si ses

fentes d’aération sont bloquées. Protégez systématiquement l’intérieur du chargeur de tout

objetétranger.

Système de protection électronique

Les appareils au Li-Ion sont équipés d’un système électronique de protection pour protéger les

blocs-piles de toute surcharge, surchauffe ou fuiteimportante.

La page charge ...

DeWalt DCS7485B Manuel utilisateur

Marque: DeWalt

Modèle: DCS7485B

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: DeWalt DCS7485B User manual
español: DeWalt DCS7485B Manual de usuario

DeWalt DCS7485B Manuel utilisateur

DeWalt DCS7485B Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents