Maruyama EH230D Le manuel du propriétaire

Marque: Maruyama

Modèle: EH230D

Catégorie: Taille-haies électriques

Taper: Le manuel du propriétaire

Ce manuel convient également à

The POWER in Outdoor Power

Completely read and understand this manual PRIOR to using this product.

Lea y entienda este manual a fondo, ANTES de usar este producto.

Lisez complètement et comprenez ce manuel AVANT d'utiliser ce produit.

OWNER'S/OPERATOR'S MANUAL

MANUAL DEL PROPIETARIO U OPERADOR

MANUEL DU PROPRIETAIRE/DE

L’UTILISATEUR

Hedge trimmer

Cortasetos

Taille-haie

EH230DSL

— US-1 —

Limited Warranty Statement

All Maruyama commercial/ industrial products are warranted to the original purchaser to be free from defects

in material and workmanship from the date of purchase for the time periods listed as follows:

Lifetime for solid steel driveshaft and ignition coils.

5 years for qualified IRON 5-YR™ commercial, institutional, or industrial use.

2 years for residential and commercial use with competitor’s oil.

90 days for rental use.

Engine - Refer to engine manufacturer’s warranty statement. Only Maruyama engines are

covered by this limited warranty statement.

Any part of a Maruyama product found to be defective within the applicable warranty period shall, at

Maruyama’s option, be repaired or replaced without charge. Warranty consideration is obtained by delivering

any Maruyama product believed to be defective to an Authorized Maruyama Servicing Dealer within the

applicable warranty period.

The purchaser shall not be charged for diagnostic labor that leads to the determination that a warranted

part is defective, if the diagnostic work is performed at a Maruyama Dealer.

Any warranted part which is not scheduled for replacement as required maintenance, or which is scheduled

only for regular inspection to the effect of “repair or replace as necessary” shall be warranted for the warranty

period. Any warranted part, which is scheduled for replacement as, required maintenance shall be warranted

for the period of time up to the first scheduled replacement point for that part. Maruyama Mfg. Co., Inc. is

liable for damages to other engine components caused by the failure of a warranted part still under warranty.

The purchaser is responsible for the performance of the required maintenance, as defined by Maruyama Mfg.

Co., Inc. in the Owner’s/Operator’s Manual.

EMISSION-RELATED PARTS WARRANTY: In addition to the above warranty coverage, Maruyama Mfg.

Co., Inc. will repair or replace, free of charge, for the original purchaser and each subsequent purchaser

any emission-related part or parts found to be defective in material and workmanship for five (5) years from

original retail delivery date. Emission-related parts are the carburetor assembly, the ignition coil as-

sembly, the ignition rotor, the spark plug, the catalytic converter and the fuel tank. Any replacement

part that is equivalent in performance and durability may be used in non-warranty maintenance or repairs,

and shall not reduce the warranty obligations of Maruyama Mfg. Co., Inc.

— US-2 —

This warranty does not cover the following:

1. Maintenance items (excluding defects in materials and workmanship) including hoses, spark plugs,

starter rope, air and fuel filters, clutch shoes, vibration isolators, throttle cables and all cutting attach-

ments, etc.

2. Extra expenses including shipping and handling, travel, payment for lost time or pay and for any in-

convenience and storage.

3. Alterations or modifications including aftermarket parts not authorized by Maruyama U.S., Inc.

4. Wear, accident, abuse, neglect, misuse, negligence, improper fuels, lubricants, fuel mixtures (when

applicable), or failure to operate or maintain the product in accordance with instructions approved by

Maruyama.

Repair or replacement as provided under this warranty is the exclusive remedy of the consumer. Maruyama

shall not be liable for any incidental or consequential damages for breach of any express or implied warranty

on these products except to the extent prohibited by applicable law. Any implied warranty of merchantability or

fitness for a particular purpose on these products is limited in duration to the warranty period as defined in the

limited warranty statement. Maruyama reserves the rights to change or improve the design of the product

without notice and does not assume obligation to update previously manufactured products.

This warranty provides you with specific legal rights, which may vary from state to state.

It is the Owner’s and Dealer’s responsibility to make sure the Warranty Registration Card is properly filled out

and mailed to Maruyama U.S., Inc. Proof of purchase and registration will be required in order to obtain war-

ranty service.

To locate an Authorized Maruyama Servicing Dealer nearest you, contact:.

Maruyama U.S., Inc.

4770 Mercantile Drive, suite100,

Fort Worth, TX

76137

U.S.A.

(940)383-7400

maruyama@maruyama-us.com

www.maruyama-us.com

— US-3 —

EH230DSL

WARNING:

Operating, servicing and maintaining this product can expose you to chemicals including

engine exhaust, carbon monoxide, phthalates, and lead, which are known to the State of

California to cause cancer and birth defects or other reproductive harm. To minimize

exposure, avoid breathing exhaust, service equipment in a well-ventilated area and wear

gloves or wash your hands frequently when servicing this equipment. For more information,

visit on the web at www.P65warnings.ca.gov.

FEDERAL EMISSION CONTROL WARRANTY STATEMENT

YOUR WARRANTY RIGHTS AND OBLIGATIONS

The U.S. Environmental Protection Agency (EPA), and Maruyama Manufacturing Company, Inc

. are

pleased to explain the emission control system warranty on your small off-road engine. New 1997 and

later model year small off-road engines must be designed, built and equipped, at the time of sale, to meet the

U.S. EPA regulations for small off-road engines. The equipment engine must be free from defects in materials

and workmanship which cause it to fail to conform with U.S. EPA standards for the first five years of engine

use from the date of sale to the ultimate purchaser. Maruyama Manufacturing Company, Inc. must warrant the

emission control system on your small off-road engine for the period of time listed above provided there has

been no abuse, neglect or improper maintenance of your small off-road engine.

Emission durability of 300 hours.

Your emission control system may include parts such as the carburetor or fuel injection system, the ignition

system, and catalytic converter. Also included may be hoses, belts, and connectors and other emission

related assemblies.

Where a warrantable condition exists, Maruyama Manufacturing Company, Inc. will repair your small off-road

engine at no cost to you, including diagnosis (if the diagnostic work is performed at an authorized dealer),

parts, and labor.

MANUFACTURER’S WARRANTY COVERAGE:

The 1997 and later model year small off-road engines are warranted for five years. If any emission-related

part on your engine is defective, the part will be repaired or replaced by Maruyama Manufacturing

Company, Inc. free of charge.

OWNER’S WARRANTY RESPONSIBILITIES:

(a) As the small off-road engine owner, you are responsible for the performance of the required

maintenance listed in your owner’s/operator’s manual.

Maruyama Manufacturing Company, Inc. recommends that you retain all receipts covering maintenance

on your small off-road engine, but Maruyama Manufacturing Company, Inc. cannot deny warranty solely

for the lack of receipts or for your failure to ensure the performance of all scheduled maintenance. Any

replacement part or service that is equivalent in performance and durability may be used in non-warranty

maintenance or repairs, and shall not reduce the warranty obligations of the engine manufacturer.

(b) As the small off-road engine owner, you should be aware, however, that Maruyama Manufacturing

Company may deny you warranty coverage if your small off-road engine or a part has failed due to

abuse, neglect, improper maintenance or unapproved modifications.

Inc. service center as soon as a problem exists. The warranty repairs should be completed in a

reasonable amount of time, not to exceed 30 days.

If you have any questions regarding your warranty rights and responsibilities, you should contact

Maruyama U.S., Inc. at 1-866-783-7400, or warranty@maruyama-us.com.

— US-4 —

COVERAGE

Maruyama Manufacturing Company, Inc. warrants to the ultimate purchaser and each subsequent

purchaser that your small off-road engine will be designed, built and equipped, at the time of sale, to meet all

applicable regulations. Maruyama Manufacturing Company, Inc. also warrants to the initial purchaser and

each subsequent purchaser that your small off-road engine is free from defects in materials and

workmanship which cause the engine to fail to conform with applicable regulations for a period of five years.

The 1997 and later model years, EPA requires manufacturers to small off-road engines for five years.

These warranty periods will begin on the date the small off-road engine is purchased by the initial

purchaser. If any emission-related part on your engine is defective, the part will be replaced by

Maruyama Manufacturing Company, Inc. at no cost to the owner.

Maruyama Manufacturing Company, Inc. shall remedy warranty defects at any authorized Maruyama

Manufacturing Company, Inc. engine dealer or warranty station. Any authorized work done at an

authorized dealer or warranty station shall be free of charge to the owner if such work determines that a

warranted part is defective. Any manufacturer-approved or equivalent replacement part may be used for

any warranty maintenance or repairs on emission-related parts, and must be provided free of charge to the

owner if the part is still under warranty, Maruyama Manufacturing Company, Inc. is liable for damages to

other engine components caused by the failure of a warranted part still under warranty.

EPA considers emission-related warranted parts to include all the parts listed below. These warranted

parts are: the carburetor assembly, the ignition coil assembly, the ignition rotor, the spark plug,

the catalytic converter, and the fuel tank.

MAINTENANCE REQUIREMENTS

The owner is responsible for the performance of the required maintenance as defined by the Maruyama

Manufacturing Company, Inc. in the owner's/operator’s manual.

LIMITATIONS

This Emission Control System Warranty shall not cover any of the following:

(a) repair or replacement required because of misuse or neglect, lack of required maintenance, repairs

improperly performed or replacements not conforming to Maruyama Manufacturing Company, Inc.

specifications that adversely affect performance and/or durability, and alterations or modifications not

recommended or approved in writing by Maruyama Manufacturing Company, Inc., and

(b) replacement of parts and other services and adjustments necessary for required maintenance at and

after the first scheduled replacement point.

Part II: CALIFORNIA EMISSIONS CONTROL WARRANTY STATEMENT

CALIFORNIA EXHAUST AND EVAPORATIVE EMISSION CONTROL WARRANTY

STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS

The California Air Resources Board and Maruyama Manufacturing Company, Inc. are pleased to explain the

exhaust and evaporative emissions (“emissions”) control system warranty on your 2020 small off-road

engine. In California, new equipment that use small off-road engines must be designed, built, and equipped to

meet the State’s stringent anti-smog standards. Maruyama Manufacturing Company, Inc. must warrant the

emissions control system on your small off-road engine for the periods of time listed below provided there has

been no abuse, neglect or improper maintenance of your small off-road engine or equipment leading to the

failure of the emissions control system.

Your emissions control system may include parts such as the carburetor or fuel-injection system, the ignition

system, catalytic converter, fuel tanks, fuel lines (for liquid fuel and fuel vapors), fuel caps, valves, canisters,

filters, clamps and other associated components. Also included may be hoses, belts, connectors, and other

emission-related assemblies.

The evaporative emission warranty parts list shall include all parts whose failure would increase evaporative

emissions, and may contain, but is not limited to, the following parts: Fuel Tank, Fuel Cap, Fuel Lines (for

liquid fuel and fuel vapors), Fuel Line Fittings, Pressure Relief Valves, Control Valves, Vacuum Control

Diaphragms, Purge Valves, Carburetor Purge Port Connector.

— US-5 —

Where a warrantable condition exists, Maruyama Manufacturing Company, Inc. will repair your small off-road

engine at no cost to you including diagnosis, parts and labor.

MANUFACTURER’S WARRANTY COVERAGE:

The exhaust and evaporative emissions control system on your small off-road engine is warranted for five

years. If any emissions-related part on your small off-road engine is defective, the part will be repaired or

replaced by Maruyama Manufacturing Company, Inc.

OWNER’S WARRANTY RESPONSIBILITIES:

• As the small off-road engine owner, you are responsible for the performance of the required maintenance

listed in your owner’s manual. Maruyama Manufacturing Company, Inc. recommends that you retain all

receipts covering maintenance on your small off-road engine, but Maruyama Manufacturing Company,

Inc. cannot deny warranty coverage solely for the lack of receipts or for your failure to ensure the

performance of all scheduled maintenance.

• As the small off-road engine owner, you should however be aware that Maruyama Manufacturing

Company, Inc. may deny you warranty coverage if your small off-road engine or a part has failed due to

abuse, neglect, or improper maintenance or unapproved modifications.

• You are responsible for presenting your small off-road engine to a Maruyama Manufacturing Company,

Inc. distribution center or service center as soon as the problem exists. The warranty repairs shall be

completed in a reasonable amount of time, not to exceed 30 days.

If you have any questions regarding your warranty rights and responsibilities, you should contact Maruyama

Manufacturing Company, Inc. at 1-866-783-7400, or warranty@maruyama-us.com.

The evaporative emission warranty parts list shall include all parts whose failure would increase

evaporative emissions, and may contain, but is not limited to, the following parts:

(1) Fuel Tank

(2) Fuel Cap

(3) Fuel Lines (for liquid fuel and fuel vapors)

(4) Fuel Line Fittings

(5) Pressure Relief Valves

(6) Control Valves

(7) Vacuum Control Diaphragms

(8) Purge Valves

(9) Carburetor Purge Port Connector

The exhaust emission warranty parts list shall include all parts whose failure would increase exhaust

emissions, and may contain, but is not limited to, the following parts:

(1) Fuel Metering System

(A) Carburetor and internal parts

(2) Cold start enrichment system

(3) Controlled hot air intake system

(4) Air filter

(5) Ignition System

(6) Spark Plug

(7) Magneto or electronic ignition system

(8) Spark advance/retard system

(9) Exhaust Gas Recirculation (EGR) System

(10) EGR valve body, and carburetor spacer if applicable

(11) Air pump or pulse valve

— US-6 —

Contents

Page US-

Limited Warranty Statement ................................. 1

Federal Emission Control ...................................... 3

California Emission Control ................................. 4

Contents ................................................................. 6

Introduction ........................................................... 6

Safety .................................................................... 7

Operator Safety ................................................ 7

Hedge trimmer Safety ......................................... 7

Fuel Safety .......................................................... 8

Hedge trimmer Operating Safety ....................... 8

Product Description ............................................... 9

Safety Decals ........................................................ 10

Symbol explanation ..............................................10

Assembly ..............................................................11

Assembling Engine and Shaft Assembly

.............11

Connecting Stop Switch Wires ....................... 11

Connecting Throttle Cable .............................. 11

Before Operation ..................................................12

Oil and Fuel .....................................................12

Mixing Gasoline And Oil ................................13

Starting And Stopping

.....................................14

Instruction of the throttle trigger

.....................16

Operation .............................................................. 16

Operating Position ...........................................16

Adjusting the angle of the blades .................... 17

Maintenance .........................................................18

Idle Speed Adjustment ....................................18

Air Filter ...........................................................19

Fuel Filter .......................................................19

Spark Plug .......................................................20

Cylinder Cooling Fins ......................................20

Spark Arrester ..................................................21

Exhaust Muffler ............................................. 21

Adjusting Cutting Blades ................................22

Cutting Blades Maintenance ...........................22

Lubrication ......................................................22

General Cleaning and Tightening ....................23

Storage ...................................................................23

Troubleshooting .....................................................24

Maintenance Period ..............................................24

Specifications ............................ End of this manual

Introduction

Thank you for purchasing a MARUYAMA product.

MARUYAMA, it’s distributors, and dealers want you

to be completely satisfied with your new product.

Please feel free to contact your local Authorized

Service Dealer for help with service, genuine

MARUYAMA parts, or other information you may

require.

Whenever you contact your Authorized Service Dealer

or the factory, always know the serial number of your

product. This number will help the Service Dealer or

Service Representative provide exact information about

your specific product. You will find the model and

serial number located in a unique place on the product

(Product Description on page US-9).

For your convenience, write the product model name

and serial number in the space to the below.

Read this manual carefully to learn how to operate and

maintain your product correctly. Reading this manual

will help you and others avoid personal injury and

damage to the product.

Although MARUYAMA designs, produces and

markets safe, state-of-the-art products, you are

responsible for using the product properly and safely.

You are also responsible for training persons who you

allow to use the product about safe operation.

The MARUYAMA warning system in this manual

identifies potential hazards and has special safety

messages that help you and others avoid personal

injury, even death. DANGER, WARNING and

CAUTION are signal words used to identify the level

of hazard. However, regardless of the hazard, be

extremely careful.

Model Name

＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿

Serial No.

＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿

— US-7 —

DANGER signals an extreme hazard that will cause

serious injury or death if the recommended precautions

are not followed.

WAR NING signals a hazard that may cause serious

injury or death if the recommended precautions are not

followed.

CAUTION signals a hazard that may cause minor or

moderate injury if the recommended precautions are

not followed. Two other words are also used to high-

light information. “Important” calls attention to special

mechanical information and “Note” emphasizes

general information worthy of special attention.

Safety

Operator Safety

1. Read and understand this Owner’s/Operator’s

Manual before using this product. Be thoroughly

familiar with the proper use of this product.

2. Never allow children to operate the Hedge

trimmer. It is not a toy. Never allow adults to

operate the unit without first reading the

Owner’s/Operator’s Manual.

3. Always wear eye protection that complies with

ANSI (American National Standards Institute)

Z87-1.

4. Always wear hearing protection.

5. Always wear heavy, long pants, a long sleeved

shirt, boots and gloves. Do not wear loose cloth-

ing, jewelry, short pants, sandals, or go barefoot.

Secure hair so it is above shoulder length.

6. Never operate this Hedge trimmer when you are

tired, ill, or under the influence of alcohol, drugs

or medication.

7. Never start or run the engine inside a closed room

or building. Breathing exhaust fumes can cause

death.

8. Keep handles clean of oil, fuel and dirt.

Hedge trimmer Safety

1. Make sure the Hedge trimmer is assembled

correctly.

2. Inspect the Hedge trimmer before each use.

Replace damaged parts. Check for fuel leaks.

Make sure all fasteners are in place and tightened

securely. Follow the maintenance instructions

beginning on page US-18.

3. Make sure the blades does not move at engine

idle speed. Refer to Idle Speed Adjustment, page

US-18.

4. Inspect the blades, guide and replace any parts

that are cracked, chipped or damaged before

using the Hedge trimmer.

5. Where the Hedge Trimmer is provided with

adjustments to the angle of the cutting device

never hold the cutter blades when making

adjustments to the working position of the cutting

device. Always ensure that the cutting device is

correctly located in a designated working position

before starting the engine or plugging in to the

mains.

6. Never use blades or replacement parts that are not

approved by MARUYAMA.

Maintain the Hedge trimmer according to the

recommended maintenance intervals and

procedures in the Maintenance section on page

US- 18.

8. Shut off the engine and be certain the blades has

completely stopped moving before inverting the

Hedge trimmer, performing maintenance on or

working on the machine.

9. If running problems or excessive vibration occur,

stop immediately and inspect the unit for the

cause. If the cause cannot be determined or is

beyond your ability to correct, return the Hedge

trimmer to your servicing dealer for repair.

10.

The Exhaust gases are extremely hot. Keep ammable

materials and objects at least 3ft. (1m) away from the

— US-8 —

direction that the exhaust gases are coming out of the

mufer. Do not cover the exhaust gases with any

items. There is a high risk of materials and objects

catching re and getting burned.

11.

During the operation and idling of the unit, the

engine is very hot. Also, for a while after the engine

stops, the engine is still hot. Do not place the engine

near ammable materials such as dried grass. There

is a high risk of materials catching re.

Fuel Safety

1. Gasoline is highly flammable and must be

handled and stored carefully. Use a container

approved for fuel to store gasoline and/or fuel/oil

mixture.

2. Mix and pour fuel outdoors, where there are no

sparks or flames.

3. Do not smoke near fuel or Hedge trimmer, or

while using the Hedge trimmer.

4. Do not overfill the fuel tank. Stop filling 1/4-1/2

in. (6 mm-13 mm) from the top of the tank.

5. Wipe up any spilled fuel before starting the

engine.

6. Move the Hedge trimmer at least 10 ft. (3m) away

from the fueling location before starting the

engine.

7. Do not remove the fuel tank cap while the engine

is running, or right after stopping the engine.

8. Allow the engine to cool before refueling.

9. Drain the tank and run the engine dry before

storing the unit.

10. Store fuel and Hedge trimmer away from open

flame, sparks and excessive heat. Make sure fuel

vapors cannot reach sparks or open flames from

water heaters, furnaces, electric motors, etc.

Hedge trimmer Operating Safety

1. THIS HEDGE TRIMMER CAN CAUSE

SERIOUS INJURIES. Read the instructions

carefully. Be familiar with all controls and the

proper use of the Hedge trimmer.

2. Inspect your work area before you begin. Remove

string, rope or similar materials which can become

entangled in the Hedge trimmer blades.

3. Keep children, bystanders and animals outside

operating area.

4. If you are approached while operating the Hedge

trimmer, stop the engine and cutting head

rotation.

5. Never allow children to operate the Hedge

trimmer.

6. Use the Hedge trimmer only in daylight or good

artificial light.

7. Always keep the Hedge trimmer on the right side

of your body.

8. Do not put hands or feet near or under any moving

parts. Keep clear at all times. Keep all parts of

your body away from the moving cutting blades

and hot surfaces such as the muffler.

9. Keep firm footing and balance. Do not overreach.

10. Do not operate the Hedge trimmer while standing

on a ladder or similar temporary support.

11. Use the right tool for the job. Do not use the

Hedge trimmer for any job that is not

recommended by MARUYAMA.

10 ft. (3 m) minimum

— US-9 —

Product Description

EH230DSL

1. Blade and Guide Bar

2. Gearcase

3. Angle Drive

4. Safety Decal

5. Shaft Assembly

6. Model Name

7. Shaft Grip

8. Throttle Trigger and Stop Switch

9. Clutch Drum Housing

10. Engine

11. Serial Number (on side of engine)

12. Air Filter

13. Fuel Tank

14. Throttle Cable and Stop Switch Wires

15. Blade Cover

— US-10 —

Safety Decals

Symbol explanation

Safety Decals are easily visible to the operator and are located near any area of potential danger.

Replace any decal that is damaged or lost.

Handling this machine improperly could result in accidents causing serious injury or death.

Read this manual carefully and practice using the trimmer until you are fully acquainted with all

operations and have learned to use it correctly.

Read and understand this Ownerʼs/Operatorʼs Manual.

Always be careful to wear a face protector, ear protector and helmet when using your Hedge

Trimmer.

Keep hands away from cutting blades.

Add grease to

gearcase every

10 hours of use.

ON SHAFT

(Part No.221501)

ON GUIDE BAR

(Part No.235595)

ON GEARCASE

(Part No. 407349)

ON GEARCASE

(Part No. 223925)

— US-11 —

Assembly

Assembling Engine and

Shaft Assembly

Attach the clutch drum housing to the engine using the

four screws supplied with the unit.

Connecting Stop Switch Wires

1. Install the plastic tube (packed with the shaft

assembly) around the throttle cable and stop

switch wires.

2. Loosen the knob and remove the air filter cover to

access the stop switch wires.

3. Plug the stop switch wires into the matching

connectors from the engine. Note that wire

polarity is not important.

Connecting Throttle Cable

With the air filter cover removed, insert the throttle

cable through the cable adjuster sleeve on the

carburetor bracket. Make sure the end of the cable

housing is seated positively in the sleeve.

2. Position the slotted fitting on the carburetor so the

recessed hole for the lug is away from the cable

adjuster sleeve.

3. Rotate the carburetor throttle cam and slip the

throttle cable through the slot in the slotted

fitting, making sure the cable lug drops into the

recessed hole.

Shaft Grip

Plastic Tube

Stop Switch Wires

Throttle Cable

Throttle Cable Housing

Stop Switch Wires

Matching

Connectors

Knob

Cable Adjuster Sleeve

Locknut

Throttle Cable

Slotted Fitting

Recessed Hole

Cable

Lug

Carburetor Bracket

Engine

Screw (4)

Clutch Drum Housing

Air Filter

Cover

Matching Connectors

Cable Adjuster

Sleeve

Throttle Stop/Idle Speed

Adjuster Screw Bracket

Carburetor Throttle Cam

Slotted Fitting

Idle Speed

Adjustment Screw

— US-12 —

4. Operate the throttle trigger a few times to make

sure that it works rightly.

5. Adjust the cable adjuster sleeve so the stop on the

carburetor throttle cam contacts the idle speed

adjustment screw and the cable position keep

1-2mm play between cable lug and slotted fittings

when the throttle trigger is fully depressed.

6. When the throttle cable is adjusted correctly,

tighten the locknut.

7. Reinstall the air filter cover and tighten the knob.

Before Operation

Oil and Fuel

1. Do not smoke near fuel.

2. Mix and pour fuel outdoors and where there are

no sparks or flames.

3. Always shut off the engine before refueling.

Never remove the fuel tank cap while the engine

is running or just right after stopping the engine.

4. Always open the fuel tank cap slowly to release

any possible overpressure inside the tank.

5. Do not overfill the fuel tank. Stop filling 1/4-1/2

in. (6 mm-13 mm) from the top of the tank.

6. Tighten the fuel tank cap carefully but firmly after

refilling.

7. Wipe up any spilled fuel before starting the

engine.

8. Move the Hedge trimmer at least 10 ft. (3m) away

from the fueling location and fuel storage

container before starting the engine.

POTENTIAL HAZARD

• In certain conditions gasoline is extreme

ly flammable and highly explosive.

WHAT CAN HAPPEN

• A fire or explosion from gasoline can

burn you, others, and cause property

damage.

HOW TO AVOID THE HAZARD

• Use a funnel and fill the fuel tank out-

doors, in an open area, when the engine

is cold. Wipe up any gasoline that spills.

•

Do not fill the fuel tank completely full.

Add gasoline to the fuel tank until the

level is 1/4 to 1/2 in. (6 mm to 13 mm)

below the bottom of the filler neck. This

empty space in the tank allows gasoline

to expand.

• Never smoke when handling gasoline,

and stay away from an open flame or

where gasoline fumes may be ignited by

a spark.

• Store gasoline in an approved container

and keep it out of the reach of children.

• Never buy more than a 30-day supply of

gasoline.

DANGER

WARNING

POTENTIAL HAZARD

• Gasoline contains gasses that can build

up pressure inside a gas tank.

WHAT CAN HAPPEN

• Fuel can be sprayed on you when

removing gas cap.

HOW TO AVOID THE HAZARD

• Remove fuel cap slowly to avoid injury

from fuel spray.

10 ft. (3 m) minimum

— US-13 —

Recommended Oil Type

Only use a two-stroke engine oil formulated for use in

high-performance, air-cooled two-stroke engines.

MARUYAMA brand two-stroke oil is formulated for

use in high-performance, air-cooled two-stroke engines

IMPORTANT: Do not use National Marine

Manufacturer’s Association (NMMA) or BIA

certified oils. This type of two-stroke engine oil

does not have the proper additives for air-

cooled, two-stroke engines and can cause

engine damage.

Do not use automotive motor oil. This type of

oil does not have the proper additives for air-

cooled, two-stroke engines and can cause

engine damage.

Recommended Fuel Type

Use clean, fresh lead-free gasoline, including

oxygenated or reformulated gasoline, with an octane

rating of 89 or higher. To ensure freshness, purchase

only the quantity of gasoline that can be used in 30

days. Use of lead-free gasoline results in fewer

combustion chamber deposits and longer spark plug

life. Use of premium grade fuel is not necessary or

recommended.

Use of Fuel Additives

IMPORTANT: NEVER USE ALCOHOL,

GASOHOL CONTAINING MORE THAN

10% ALCOHOL BECAUSE ENGINE FUEL

SYSTEM DAMAGE COULD RESULT.

DO NOT USE FUEL ADDITIVES OTHER

THAN THOSE MANUFACTURED FOR

FUEL STABILIZATION DURING STORAGE

SUCH AS MARUYAMA’S STABILIZER/

CONDITIONER OR A SIMILAR PRODUCT.

MARUYAMA’S STABILIZER/CONDITION-

ER IS A PETROLEUM DISTILLATE BASED

CONDITIONER/STABILIZER.

MARUYAMA DOES NOT RECOMMEND

STABILIZERS WITH AN ALCOHOL BASE

SUCH AS ETHANOL, METHANOL OR ISO-

PROPYL. ADDITIVES SHOULD NOT BE

USED TO TRY TO ENHANCE THE POWER

OR PERFORMANCE OF MACHINE.

Mixing Gasoline And Oil

IMPORTANT: The engine used on this

Hedge trimmer is of a two-stroke design. The

internal moving parts of the engine, i.e.,

crankshaft bearings, piston pin bearings and

piston to cylinder wall contact surfaces, require

oil mixed with the gasoline for lubrication.

Failure to add oil to the gasoline or failure to

mix oil with the gasoline at the appropriate

ratio will cause major engine damage which

will void your warranty.

For your fuel premix, use MARUYAMA

Premium two-stroke Oil Mix, or equivalent

ISO-L-EGD & JASO FD oil with a minimum

89 octane high quality gasoline. MARUYAMA

two-stroke oil is specially formulated to meet

the requirements of high-performance, low-

emission air-cooled two-stroke engines. Use of

other oils may lead to service issues which may

not be covered by your warranty.

Fuel Mixture

The fuel: oil ratio is 50 parts gasoline to 1 part oil or

50:1.

NOTE: Never use a mixing ratio less than

50:1 regardless of the oil package mixing

instructions. Ratios less than 50:1, (for example,

60:1, 80:1, 100:1), reduce the amount of

lubrication to the internal moving parts of

the engine and can cause damage.

Fuel Mixture Chart

Gasoline 50:1 two-stroke oil

1 gallon 2.6 oz

2 gallons 5.1 oz.

5 gallons 12.8 oz.

1 liter 20 mL

5 liters 100 mL

50:1

— US-14 —

Mixing Instructions

IMPORTANT: Never mix gasoline and oil

directly in the Hedge trimmer fuel tank.

1. Always mix fuel and oil in a clean container

approved for gasoline.

2. Mark the container to identify it as fuel mix for

the Hedge trimmer.

3. Use regular unleaded gasoline and fill the

container with half the required amount of

gasoline.

4. Pour the correct amount of oil into the container

then add the remaining amount of gasoline.

5. Close the container tightly and shake it

momentarily to evenly mix the oil and the

gasoline before filling the fuel tank on the Hedge

trimmer.

6. When refilling the Hedge trimmer fuel tank, clean

around the fuel tank cap to prevent dirt and debris

from entering the tank during cap removal.

7. Always shake the premix fuel container

momentarily before filling the fuel tank.

8. Always use a spout or funnel when fueling to

reduce fuel spillage.

9. Fill the tank only to within 1/4-1/2 in. (6 mm-13

mm) from the top of the tank. Avoid filling to the

top of the tank filler neck.

Starting And Stopping

Before Starting The Engine

1. Fill the fuel tank as instructed in the Before

Operation section of this manual (US-12).

2. Rest the Hedge trimmer on the ground.

3. Make sure the cutting attachment is clear of any

broken glass, nails, wire, rocks or other debris.

4. Keep all bystanders, children and animals away

from the working area.

Cold Starting Procedure

This engine is equipped with a fuel primer and a choke

system. To start a “cold” engine properly, perform the

following procedure:

1. Pump the primer bulb at the bottom of the

carburetor until fuel can be seen flowing through

the fuel return line to the fuel tank.

(Flowing fuel should be almost clear, not foamy

or full of bubbles.)

2. Move the choke lever to the closed (

) position.

And move the control lever to the high speed side

approximately half in. from the low speed side.

Primer Bulb

Fuel

Return

Line

Choke Lever

Starter Grip

Control Lever

Throttle Lever

Throttle Trigger

Low speed

High speed

— US-15 —

3. Grasp the throttle lever then push the fast-idle

lock button. Release your hand with holding the

fast-idle lock button to lock the fast-idle.

4. Pull the starter grip.

5. After the engine starts, squeeze and release the

throttle trigger to return it to the idle position, then

move the choke lever to the open (

) position.

If the engine stops running before you move the

choke lever to the open (

) position:

Go ahead and open the choke, pull the starter grip

with the throttle trigger positioned at Fast-idle

position.

Hot Restart

To start an engine that is already warmed up (hot restart),

or if the ambient temperature exceeds 68°F (20°C):

1. Pump the primer bulb at the bottom of the

carburetor until fuel can be seen flowing through

the fuel return line to the fuel tank.

(Flowing fuel should be almost clear, not foamy

or full of bubbles.)

2. Move the choke lever to the open (

) position.

3. Leave the throttle trigger in the idle position and

pull the starter grip.

4. If the engine fails to start after three to four pulls,

follow the instruction in the Cold Starting

Procedure section (US-14).

If the engine fails to start after you follow the

above procedures, contact an authorized

MARUYAMA dealer.

To Stop The Engine

1. Release the throttle trigger.

2. Slide the stop switch to the “STOP” (OFF)

position.

POTENTIAL HAZARD

• The components of your recoilstarter

assembly are under high spring tension.

If improperly disassembled these parts

maystrike you with considerable force,

possibly causing personal injury.

WHAT CAN HAPPEN

• Contact with the parts can cause severe

personal injury.

HOW TO AVOID THE HAZARD

• Never attempt to disassemble your

recoil starter assembly yourself.

Always consult your authorized

MARUYAMA dealer for repair by quali

fied service technicians.

WARNING

CAUTION

• Do not pull the Starter rope all the way

out.

Fast-idle lock button

Stop Switch

— US-16 —

Instruction of the throttle trigger

Start the blade rotation

1. Grasp the throttle lever.

2. Move the control lever to high speed side slowly.

3. Then engine speed increase gradually, and the

blade starts rotation.

4. Adjust the blade rotational speed by the control

lever.

Note: Engine speed does not increase by

grasping the throttle lever If the control

lever is positioned at low speed side fully.

Stop the blade rotation

1. The engine speed will down to idling by moving

the control lever to low speed position fully, or

releasing the throttle lever.

2. If you did not change the control lever position,

engine speed become to the original adjusted

speed when grasp the throttle lever again.

Operation

Operating Position

Before using the Hedge Trimmer, check the following.

1. The Hedge trimmer should be on the operator’s

right side.

2. The operator’s right hand should be holding the

shaft grip, with his or her fingers on the throttle

trigger. The right arm should be slightly bent.

3. The left hand should be holding the shaft grip

with the fingers.

4. The Hedge Trimmer weight should be evenly

distributed between the arms. Before using the

Hedge trimmer check the following:

5. Make sure the blades are moving (at least half

throttle) before actual cutting begins. The Hedge

Trimmer performs best at full throttle.

6. Always release the throttle trigger and allow the

engine to return to idle speed when not cutting.

7. Stop the engine when moving between work sites.

CAUTION

• The thickness of branches which may be

cut using this trimmer is limited to up

to approximately 3/16 in. (4.8 mm). Never

tr y to cut branches thicker than this, as

doing so may result in damage to the

trimmer.

CAUTION

• Read the Safety instructions on page

US-7 concerning proper use of the

Hedge Trimmer.

CAUTION

• Do not touch the sharpened edges of

the cutting blades. The cutting blades

are extremely sharp and dangerous at

all times. Always wear gloves to help

protect your hands and fingers from

injury.

Throttle Lever

Low speed

High speed

Blade Rotate

Blade Stop

Control Lever

— US-17 —

• If the cutting blades becomes jammed, stop the

engine immediately.

• Make certain all moving parts have stopped and

disconnect the spark plug before inspecting the

equipment for damage.

• Never use a Hedge Trimmer that has chipped,

cracked or broken Blades.

Adjusting the angle of the blades

NOTE: Never use the unit if the blade angle is

not 48 degrees upwards to 84 degrees

downward.

1. First stop the engine. Next attach the blade cover.

Turn the clamp knob counter clock wise until the

clamp knob stops. Angle adjustments are not

possible without completely loosening the clamp

knob.

3. Always hold the handle when adjusting the

blades. The blades adjust from a 48 degree

upward angle to an 84 degree downward angle.

Never push the lock lever when adjusting the

angle of the blades.

4. After you have adjusted the angle of the blades

tighten the clamp knob firmly and fix the

gearcase in place. When tightening the clamp

knob, make sure both racks engage.

Folding procedure

1. First stop the engine. Next attach the blade cover.

2. Turn the clamp knob counter clockwise until the

clamp knob stops. Folding the unit is not possible

without the clamp knob completely loosened.

3. Hold the handle securely, and then fold the blades

approximately 180 degrees while pushing the

lock pin downward. Do not touch the lock lever

except when folding the blades.

4. After folding the unit, tighten the clamp knob

firmly and fix the gearcase. When tightening the

clamp knob make sure that both racks are

engaged.

Engage racks evenly

Lock Lever

(Push downward)

Clamp Knob

Handle

Gearcase

Not

Engaged

Blade Cover

Engaged

Down to 84°

Up to 48°

Loosen

Tighten

CAUTION

• Do not touch the sharpened edges of

the cutting blades. The cutting blades

are extremely sharp and dangerous at

all times. Always wear gloves to help

protect your hands and fingers from

injury.

• Do not hold any part other than the

handle when adjusting the angle of the

blades.

• Stop the engine when adjusting the

angle of the blades.

— US-18 —

Maintenance

Maintenance, replacement or repair of emission

control devices and systems may be performed by

any repair establishment or individual; however,

warranty repairs must be performed by a dealer or

service center authorized by MARUYAMA

Manufacturing Company, Inc. The use of parts that

are not equivalent in performance and durability to

authorized parts may impair the effectiveness of the

emission control system and may have a bearing on

the outcome of a warranty claim.

Maintenance on today's low-emission engines is

even more critical for longest life and best

performance. Particularly critical are air and fuel

filters, spark plug heat range, cooling air intake

area and proper gaps of coil and plug.

Idle Speed Adjustment

This Hedge trimmer is equipped with non-adjustable

fuel mixture carburetor. The engine idle speed is the

only adjustment for the operator.

The cutting blades may be moving during idle speed

adjustment. Wear the recommended personal protec-

tive equipment and observe all safety instructions.

Keep hands and body away from the blades.

When the throttle trigger is released, the engine should

return to an idle speed between 2700 - 3300 RPM, or

just below the clutch engagement speed. The blades

must not move and the engine should not stall (stop

running) at engine idle speed.

To adjust the engine idle speed, rotate the idle speed

adjustment screw on the carburetor.

• Turn the idle speed screw in (clockwise) to

increase the engine idle speed.

• Turn the screw out (counter-clockwise) to decrease

the engine idle speed.

If idle speed adjustment is necessary, and after

adjustment the cutting head rotates or the engine

stalls, stop using the Hedge Trimmer immediately!

Contact your local authorized MARUYAMA Dealer

for assistance and servicing.

• Idle speed adjustment should be

checked each time the unit is operated.

WARNING

POTENTIAL HAZARD

• Engine must be running to make carbu

retor adjustments.

• When engine is running, blades are

moving and other parts are moving.

WHAT CAN HAPPEN

• Contact with moving blades or other

moving parts could cause serious per

sonal injury or death.

HOW TO AVOID THE HAZARD

• Keep hands, feet and clothing away from

cutting head and other moving parts.

• Keep all bystanders and pets away

from unit while making carburetor

adjustments.

WARNING

Idle Speed

Adjustment Screw

— US-19 —

Air Filter

Maintenance Interval

• The air filter should be cleaned daily, or more

often when working in extremely dusty conditions.

• Replace after every 100 hours of operation.

Air Filter Cleaning

1. Loosen the knob and remove the air filter cover.

2. Remove the foam element and filter screen from

the air filter body.

3. Clean the foam element and filter screen with

warm, soapy water. Let the screen and element

dry completely.

4. Apply a light coat of motor oil (SAE 30 or

equivalent viscosity) to the foam element and

squeeze out all excess oil.

5. Reassemble the filter screen and foam element to

the air filter body.

6. Reinstall the air filter cover and tighten the knob.

Fuel Filter

Maintenance Interval

• The fuel filter should be replaced after every 100

hours of operation.

• Fuel filters needing more frequent replacement

may indicate debris in fuel tank.

Fuel Filter Replacement

The fuel filter is attached to the end of the fuel pick-up

hose inside the fuel tank.

To replace the fuel filter:

1. Make sure the fuel tank is empty.

2. Remove the fuel cap.

3. Using a wire hook, gently pull the fuel filter out

through the fuel filler opening.

Use caution not to “fishhook” the fuel hose.

Replace immediately if punctured!

4. Grasp the fuel hose next to the fuel filter fitting

and remove the filter, but do not release the hose.

5. While still holding on to the fuel hose, attach the

new fuel filter.

6. Drop the new fuel filter back into the fuel tank.

7. Make sure that the fuel filter is not stuck in a

corner of the tank, and that the fuel hose is not

doubled over (kinked) before refueling.

Fuel Filter

Fuel Pick-up Hose

Wire

Air Filter Cover

Filter Screen

Foam Element

La page charge ...

Maruyama EH230D Le manuel du propriétaire

Marque: Maruyama

Modèle: EH230D

Catégorie: Taille-haies électriques

Taper: Le manuel du propriétaire

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Maruyama EH230D Owner's manual
español: Maruyama EH230D El manual del propietario
português: Maruyama EH230D Manual do proprietário

Maruyama EH230D Le manuel du propriétaire

Ce manuel convient également à

Maruyama EH230D Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents