LG PM15SP.NSJ Manuel utilisateur

INSTALLATION MANUAL

AIR

CONDITIONER

www.lg.com

[Representative] LG Electronics Inc. EU Representative :

LG Electronics European Shared Service Center B.V.

Krijgsman 1, 1186 DM Amstelveen, The Netherlands

[Manufacturer]

MFL67855550

Rev.00_021319

Please read this installation manual completely before installing the product.

Installation work must be performed in accordance with the national wiring

standards by authorized personnel only.

Please retain this installation manual for future reference after reading it thoroughly.

WALL MOUNTED

Original instruction

ENGLISH ITALIANO ESPAÑOL FRANÇAIS DEUTSCH

ΕΛΛΗΝΙΚΆ

ČEŠTINA

NEDERLANDS

POLSKI

LIMBA ROMÂNĂ

ENGLISH

MODEL DESIGNATION

2

The A-weighted sound pressure emitted by

this product is below 70 dB.

** The noise level can vary depending on the

site.

The figures quoted are emission level and are

not necessarily safe working levels.

Whilst there is a correlation between the

emission and exposure levels, this cannot be

used reliably to determine whether or not

further precautions are required.

Factor that influence the actual level of

exposure of the workforce include the

characteristics of the work room and the other

sources of noise, i.e. the number of

equipment and other adjacent processes and

the length of time for which an operator

exposed to the noise. Also, the permissible

exposure level can vary from country to

country.

This information, however, will enable the

user of the equipment to make a better

evaluation of the hazard and risk.

Airborne Noise Emission

Limiting concentration is the limit of Freon gas

concentration where immediate measures can

be taken without hurting human body when

refrigerant leaks in the air. The limiting

concentration shall be described in the unit of

kg/m

3

(Freon gas weight per unit air volume)

for facilitating calculation

Total amount of replenished

refrigerant in refrigerant facility (kg)

Capacity of smallest room where

indoor unit is installed (m

3

)

Refrigerant

concentration

(kg/m

3

)

=

Limiting concentration: 0.44kg/m

3

(R410A)

Limiting concentration

n Calculate refrigerant concentration

MODEL DESIGNATION

Product information

Model Suffix

- Product Name : Air conditioner

- Model Name :

- Additional Information : serial number is

refer to the barcode on the product.

- Max allowable pressure High side :

4.2 Mpa / Low side : 2.4 Mpa

- Refrigerant : R410A / R32

P M S P07 N SJ

(7) Chassis

(6) Indoor(N)

(5) Serial

(4) Product Look

(3) Capacity (kBTU)

(2) Product

(1) Product Type 1

D Deluxe

P Standard Plus/Standard

A Artcool

(4) Product Look

R R-Look

S Semi R-Look

E E-Look

B Black Mirror Look

M Multi Compitable

(2) Product

SJ Chassis

SK Chassis

(7) Chassis

TIPS FOR SAVING ENERGY

ENGLISH

3

• Do not cool excessively indoors. This may be harmful for your health and may consume more

electricity.

• Block sunlight with blinds or curtains while you are operating the air conditioner.

• Keep doors or windows closed tightly while you are operating the air conditioner.

• Adjust the direction of the air flow vertically or horizontally to circulate indoor air.

• Speed up the fan to cool or warm indoor air quickly, in a short period of time.

• Open windows regularly for ventilation as the indoor air quality may deteriorate if the air

conditioner is used for many hours.

• Clean the air filter once every 2 weeks. Dust and impurities collected in the air filter may block the

air flow or weaken the cooling / dehumidifying functions.

For your records

Staple your receipt to this page in case you need it to prove the date of purchase or for warranty

purposes. Write the model number and the serial number here:

Model number :

Serial number :

You can find them on a label on the side of each unit.

Dealer’s name :

Date of purchase :

Here are some tips that will help you minimize the power consumption when you use the air

conditioner. You can use your air conditioner more efficiently by referring to the instructions

below:

TIPS FOR SAVING ENERGY

4

IMPORTANT SAFETY INSTRUCTIONS

ENGLISH

IMPORTANT SAFETY INSTRUCTIONS

The following symbols are displayed on indoor and outdoor units.

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE.

Always comply with the following precautions to avoid dangerous

situations and ensure peak performance of your product

WARNING

It can result in serious injury or death when the directions are ignored

CAUTION

It can result in minor injury or product damage when the directions are

ignored

WARNING

• Installation or repairs made by unqualified persons can result in

hazards to you and others.

• Installation MUST conform with local building codes or, in the absence

of local codes, with the Nation Electrical Code NFPA 70/ANSI C1-1003

or current edition and Canadian Electrical Code Part1 CSA C.22.1.

• The information contained in the manual is intended for use by a

qualified service technician familiar with safety procedures and

equipped with the proper tools and test instruments.

• Failure to carefully read and follow all instructions in this manual can

result in equipment malfunction, property damage, personal injury

and/or death.

• Compliance with national gas regulations shall be observed.

Installation

• Always perform grounding.

- Otherwise, it may cause electrical shock.

• Don’t use a power cord, a plug or a loose socket which is damaged.

- Otherwise, it may cause a fire or electrical shock.

!

Read the precautions in this manual

carefully before operating the unit.

This appliance is filled with

flammable refrigerant (R32)

This symbol indicates that the

Operation Manual should be read

carefully.

This symbol indicates that a service

personnel should be handling this

equipment with reference to the

Installation Manual.

5

ENGLISH

IMPORTANT SAFETY INSTRUCTIONS

• For installation of the product, always contact the service center or a

professional installation agency.

- Otherwise, it may cause a fire, electrical shock, explosion or injury.

• Securely attach the electrical part cover to the indoor unit and the

service panel to the outdoor unit.

- If the electrical part cover of the indoor unit and the service panel of

the outdoor unit are not attached securely, it could result in a fire or

electric shock due to dust, water, etc.

• Always install an air leakage breaker and a dedicated switching board.

- No installation may cause a fire and electrical shock.

• Do not keep or use flammable gases or combustibles near the air

conditioner.

- Otherwise, it may cause a fire or the failure of product.

• Ensure that an installation frame of the outdoor unit is not damaged

due to use for a long time.

- It may cause injury or an accident.

• Do not disassemble or repair the product randomly. - It will cause a

fire or electrical shock.

• Do not install the product at a place that there is concern of falling

down.

- Otherwise, it may result in personal injury.

• Use caution when unpacking and installing. - Sharp edges may cause

injury.

• The appliance shall be stored in a room without continuously

operating ignition sources

(for example: open flames, an operating gas appliance or an operating

electric heater.)

• Two or more people must lift and transport the product. Avoid

personal injury.

• Do not use means to accelerate the defrosting process or to clean,

other than those recommended by the manufacturer.

• Do not pierce or burn refrigerant cycle part.

• Be aware that refrigerants may not contain an odour.

• Keep any required ventilation openings clear of obstruction.

• The appliance shall be stored in a well-ventilated area where the room

size corresponds to the room area as specified for operation.

• Refrigerant tubing shall be protected or enclosed to avoid damage.

ENGLISH

IMPORTANT SAFETY INSTRUCTIONS

6

• Flexible refrigerant connectors (such as connecting lines between the

indoor and outdoor unit) that may be displaced during normal

operations shall be protected against mechanical damage.

• A brazed, welded, or mechanical connection shall be made before

opening the valves to permit refrigerant to flow between the

refrigerating system parts.

• Mechanical connections shall be accessible for maintenance

purposes.

Operation

• Do not share the outlet with other appliances. - It will cause an electric

shock or a fire due to heat generation.

• Do not use the damaged power cord.

- Otherwise, it may cause a fire or electrical shock.

• Do not modify or extend the power cord randomly.

- Otherwise, it may cause a fire or electrical shock.

• Take care so that the power cord may not be pulled during operation.

- Otherwise, it may cause a fire or electrical shock.

• Unplug the unit if strange sounds, smell, or smoke comes from it.

- Otherwise, it may cause electrical shock or a fire.

• Keep the flames away.

- Otherwise, it may cause a fire.

• Take the power plug out if necessary, holding the head of the plug

and do not touch it with wet hands.

- Otherwise, it may cause a fire or electrical shock.

• Do not use the power cord near the heating tools.

- Otherwise, it may cause a fire and electrical shock.

• Do not open the suction inlet of the indoor/outdoor unit during

operation.

- Otherwise, it may electrical shock and failure.

• Do not allow water to run into electrical parts.

- Otherwise, it may cause the failure of machine or electrical shock.

• Hold the plug by the head when taking it out. - It may cause electric

shock and damage.

• Never touch the metal parts of the unit when removing the filter. -

They are sharp and may cause injury.

• Do not step on the indoor/outdoor unit and do not put anything on it. -

It may cause an injury through dropping of the unit or falling down.

IMPORTANT SAFETY INSTRUCTIONS

ENGLISH

7

• Do not place a heavy object on the power cord.

- Otherwise, it may cause a fire or electrical shock.

• When the product is submerged into water, always contact the

service center.

- Otherwise, it may cause a fire or electrical shock.

• Take care so that children may not step on the outdoor unit.

- Otherwise, children may be seriously injured due to falling down.

• Use a vacuum pump or inert (nitrogen) gas when doing leakage test or

air purge. Do not compress air or oxygen, and do not use flammable

gases.

Otherwise, it may cause fire or explosion. - There is the risk of death,

injury, fire or explosion.

• Do not turn on the breaker or power under condition that front panel,

cabinet, top cover, control box cover are removed or opened.

- Otherwise, it may cause fire, electric shock, explosion or death.

• Turn off all devices that cause fire when the refrigerant leaks.,

ventilate the room (example : opening window or using ventilation

unit), and contact with dealer who you purchased the unit.

• The installation of pipe-work shall be kept to a minimum.

• When mechanical connectors are reused indoors, sealing parts shall

be renewed.(for R32)

• When flared joints are reused indoors, the flare part shall be re-

fabricated.(for R32)

CAUTION

Installation

• Install the drain hose to ensure that drain can be securely done. -

Otherwise, it may cause water leakage.

• Install the product so that the noise or hot wind from the outdoor unit

may not cause any damage to the neighbors.

- Otherwise, it may cause dispute with the neighbors.

• Always inspect gas leakage after the installation and repair of product.

- Otherwise, it may cause the failure of product.

• Keep level parallel in installing the product. - Otherwise, it may cause

vibration or water leakage.

• Any person who is involved with working on or breaking into a

!

8

IMPORTANT SAFETY INSTRUCTIONS

ENGLISH

refrigerant circuit should hold a current valid certificate from an

industry-accredited assessment authority, which authorises their

competence to handle refrigerants safely in accordance with an

industry recognised assessment specification. (for R32)

• Wear adequate personal protection equipment (PPE) when installing,

maintaining or servicing the product.

Operation

• Avoid excessive cooling and perform ventilation sometimes.

- Otherwise, it may do harm to your health.

• Use a soft cloth to clean. Do not use wax, thinner, or a strong

detergent. - The appearance of the air conditioner may deteriorate,

change color, or develop surface flaws.

• Do not use an appliance for special purposes such as preserving

animals vegetables, precision machine, or art articles.

- Otherwise, it may damage your properties.

• Do not place obstacles around the flow inlet or outlet.

- Otherwise, it may cause the failure of appliance or an accident.

• The appliance shall be stored so as to prevent mechanical damage

from occurring.

• Servicing shall only be performed as recommended by the equipment

manufacturer. Maintenance and repair requiring the assistance of

other skilled personnel shall be carried out under the supervision of

the person competent in the use of flammable refrigerants. (for R32)

• Dismantling the unit, treatment of the refrigerant oil and eventual

parts should be done in accordance with local and national standards.

• Periodic ( more than once/year ) cleaning of the dust or salt particles

stuck on the heat exchanger by using water.

• Means for disconnection must be incorporated in the fixed wiring in

accordance with the wiring rules

ENGLISH

9

2 MODEL DESIGNATION

3 TIPS FOR SAVING ENERGY

4 IMPORTANT SAFETY INSTRUCTIONS

10 INTRODUCTION

10 Symbols used in this Manual

10 Features

11 INSTALLATION PARTS

11 INSTALLATION TOOLS

12 INSTALLATION MAP

13 INSTALLATION

13 Select the best Location

13 Outdoor unit

15 Fixing Installation Plate

15 Drill a Hole in the Wall

15 Flaring Work

16 Connecting the Piping

21 Connecting the Cables

23 Checking the Drainage

24 Installing drain piping of the outdoor unit

24 Forming the Piping

25 Air P

urging

25 Air purging with vacuum pump

28 Tes t R unning

29 Heating Only Mode

30 SMART DIAGNOSIS

31Installation guide at theseaside

32Piping Length and Elevation

33 Manual the decor, air ﬁlter Assembly & Disassembly

TABLE OF CONTENTS

10

INTRODUCTION

ENGLISH

!

Air Intake Vents

Connecting

Wires

Piping

Air Outlet Vents

Base Plate

Drain Hose

* The feature can be changed according to type of model.

NOTE

!

• When mechanical connectors are reused indoors, sealing parts shall be renewed.

Front grille

Air ﬁlter

On/Off button

Signal receiver

Display

Plasmaster Ionizer

Air deﬂector

(Vertical louver & Horizontal vane)

Air outlet

Symbols used in this Manual

This symbol alerts you to the risk of electric shock.

This symbol alerts you to hazards that may cause harm to the air conditioner.

This symbol indicates special notes.

Features

!

INTRODUCTION

INSTALLATION PARTS

ENGLISH

11

INSTALLATION TOOLS

Name

Quantity Shape

Installation plate

1 EA

Cloth tape

Connector

1 EA

Type "A" screw

5 EA

Type "B" screw

2 EA

Type "C" screw

2 EA

Remote control

holder

1 EA

1 EA (5.0 kW)

2 EA (6.6 kW)

The feature can be changed according to type of model.

Type “B” screw

5.0 kW : ڸØ9.52 (3/8) ơ Ø12.7 (1/2)

6.6 kW : ڸØ9.52 (3/8) ơ Ø12.7 (1/2)

ڹØ15.88 (5/8) ơ Ø12.7 (1/2)

Screws for fixing panels are attached to decoration panel.

When Indoor unit (5.0/6.6 kW) is connected to the Multi Outdoor unit, use the connector.

Figure FigureName

Screw driver

Electric drill

Measuring tape, Knife

Hole core drill

Spanner

Torque wrench

Multi-meter

Hexagonal wrench

Ammeter

Gas-leak detector

Thermometer,

Level

Flaring tool set

Name

INSTALLATION PARTS

12

INSTALLATION MAP

ENGLISH

Connecting cable

(Optional Parts)

Vinyl tape (Wide)

• Apply after carrying out a

drainage test.

• To carry out the drainage

test, remove the air ﬁlters

and pour water into the heat

exchanger.

Saddle

Gas side piping (Optional Parts)

Liquid side piping (Optional Parts)

Additional drain pipe

Vinyl tape (Narrow)

Drain hose

Installation plate

Sleeve

Bushing-Sleeve

Putty(Gum Type Sealant)

Bend the pipe as closely

on the wall as possible,

but be careful that it

doesn't break.

NOTE

!

• You should purchase the installation parts. (lt can be changed according to market)

* The feature can be changed according a type of model.

* Work to the vinyl tape should up from below.

INSTALLATION MAP

INSTALLATION

ENGLISH

13

* The feature can be changed according to

type of model.

* The feature can be changed according to

type of model.

More Than

200

More Than

100

More Than

100

(Unit : mm)

More Than

2 300

More than

300

More than

300

Sunroof

Fence or

obstacles

More than

700

More than

600

(Unit : mm)

NOTE

!

The gap between the indoor unit and

ceiling is needed more than 200 mm for

disassemble the air filter.

Outdoor unit

- If an awning is built over the unit to prevent

direct sunlight or rain exposure, make sure

that heat radiation from the condenser is not

restricted.

- Ensure that the space around the back and

sides is more than 300 mm. The space in

front of the unit should be more than 700 mm

of space.

- Do not place animals and plants in the path of

the warm air.

- Take the weight of the air conditioner into

account and select a place where noise and

vibration are minimum.

- Select a place where the warm air and noise

from the air conditioner do not disturb

neighbors.

Select the best Location

- There should not be any heat or steam near

the unit.

- Select a place where there are no obstacles

around of the unit.

- Make sure that condensation drainage can

be conveniently routed away.

- Do not install near a doorway.

- Ensure that the interval between a wall and

the left (or right) of the unit is more than

100mm. The unit should be installed as high

as possible on the wall, allowing a minimum

of 200 mm from ceiling.

- Use a metal detector to locate studs to

prevent unnecessary damage to the wall.

INSTALLATION

14

INSTALLATION

ENGLISH

- The appliance shall be installed, operated and stored in a room with a floor area larger than the

minimum area.

- Use the graph of table to determine the minimum area.

- m : Total refrigerant amount in the system

- Total refrigerant amount : factory refrigerant charge + additional refrigerant amount

- Amin : minimum area for installation

Minimum ﬂoor area

0

100

200

300

400

500

600

Amin (m

2

)

m (kg)

0 1.224 2 3 4 5 6 7 8

Floor standing

Wall mounted

Ceiling mounted

Floor location

m (kg) Amin (m

2

)

< 1.224

-

1.224

12.9

1.4 16.82

1.6 21.97

1.8 27.80

2 34.32

2.2 41.53

2.4 49.42

2.6 58.00

2.8 67.27

3 77.22

3.2 87.86

3.4 99.19

3.6 111.20

3.8 123.90

4 137.29

4.2 151.36

4.4 166.12

Floor location

m (kg) Amin (m

2

)

4.6 181.56

4.8 197.70

5 214.51

5.2 232.02

5.4 250.21

5.6 269.09

5.8 288.65

6 308.90

6.2 329.84

6.4 351.46

6.6 373.77

6.8 396.76

7 420.45

7.2 444.81

7.4 469.87

7.6 495.61

7.8 522.04

Wall mounted

m (kg) Amin (m

2

)

< 1.224

-

1.224

1.43

1.4 1.87

1.6 2.44

1.8 3.09

2 3.81

2.2 4.61

2.4 5.49

2.6 6.44

2.8 7.47

3 8.58

3.2 9.76

3.4 11.02

3.6 12.36

3.8 13.77

4 15.25

4.2 16.82

4.4 18.46

Wall mounted

m (kg) Amin (m

2

)

4.6 20.17

4.8 21.97

5 23.83

5.2 25.78

5.4 27.80

5.6 29.90

5.8 32.07

6 34.32

6.2 36.65

6.4 39.05

6.6 41.53

6.8 44.08

7 46.72

7.2 49.42

7.4 52.21

7.6 55.07

7.8 58.00

Ceiling Mounted

m (kg) Amin (m

2

)

< 1.224

-

1.224

0.956

1.4 1.25

1.6 1.63

1.8 2.07

2 2.55

2.2 3.09

2.4 3.68

2.6 4.31

2.8 5.00

3 5.74

3.2 6.54

3.4 7.38

3.6 8.27

3.8 9.22

4 10.21

4.2 11.26

4.4 12.36

Ceiling Mounted

m (kg) Amin (m

2

)

4.6 13.50

4.8 14.70

5 15.96

5.2 17.26

5.4 18.61

5.6 20.01

5.8 21.47

6 22.98

6.2 24.53

6.4 26.14

6.6 27.80

6.8 29.51

7 31.27

7.2 33.09

7.4 34.95

7.6 36.86

7.8 38.83

(for R32)

INSTALLATION

ENGLISH

15

Fixing Installation Plate

The wall you select should be strong and solid

enough to prevent vibration

1 Mount the installation plate on the wall

with type "A" screws. If mounting the unit

on a concrete wall, use anchor bolts.

- Mount the installation plate horizontally

by aligning the centerline using Horizontal

meter.

2 Measure the wall and mark the centerline.

It is also important to use caution

concerning the location of the installation

plate. Routing of the wiring to power

outlets is through the walls typically.

Drilling the hole through the wall for piping

connections must be done safely.

Drill a Hole in the Wall

- Drill the piping hole with a ø65mm hole core

drill. Drill the piping hole at either the right or

the left with the hole slightly slanted to the

outdoor side.

Flaring Work

Main cause for gas leakage is due to defect of

flaring work. Carry out correct flaring work in

the following procedure.

Cut the pipes and the cable

1 Use the piping kit accessory or the pipes

purchased locally.

2 Measure the distance between the indoor

and the outdoor unit.

3 Cut the pipes a little longer than measured

distance.

4 Cut the cable 1.5 m longer than the pipe

length.

5-7 mm

(3/16"~5/16")

Indoor

WALL

Outdoor

Copper

pipe

90°

Slanted Uneven Rough

Installation Plate

Chassis

Hook

Chassis

Hook

Type "A" Screws

C Type: 494 C Type: 504

Place a level on raised tab

Unit Outline

83

C Type: 134

Measuring Tape

Ø65

83

Measuring Tape

Hanger

Ø65

C Type: 150

(Unit : mm)

194152

Ø65

Right rear piping

Left rear piping

Ø65

C Type : 134C Type : 98

C Type

C Type : 418 C Type : 418

Place a level on raised tab

Unit Outline

Installation Plate

NOTE

!

• Use the deoxidised copper as piping

materials to install.

16

INSTALLATION

ENGLISH

Inclined

Inside is shiny without scratches

Smooth all round

Even length

all round

Surface

damaged

Cracked Uneven

thickness

= Improper ﬂaring =

Burrs removal

1 Completely remove all burrs from the cut

cross section of pipe/tube.

2 While removing burrs put the end of the

copper tube/pipe in a downward direction

while removing burrs location is also

changed in order to avoid dropping burrs

into the tubing.

Putting nut on

- Remove flare nuts attached to indoor and

outdoor unit, then put them on pipe/tube

having completed burr removal.

(not possible to put them on after finishing

flare work)

Flaring work

1 Firmly hold copper pipe in a bar with the

dimension shown in below table.

2 Carry out flaring work with the flaring tool.

Check

1 Compare the flared work with the figure

by.

2 If a flared section is defective, cut it off

and do flaring work again.

Connecting the Piping

1 Pull the cover at the bottom of the indoor

unit. Pull the cover ①→②.

2 Remove the cover from the indoor unit.

Pipe

Reamer

Point down

Flare nut

Copper tube

NOTE

!

• Temper grade of pipe: Annealed.

NOTE

!

• When flared joints are reused indoors,

the flare part shall be re-fabricated.

Bar

"A"

Copper

pipe

Pipe diameter

Inch (mm)

A Inch (mm)

Thickness

Inch (mm)

Wing nut type

Clutch type

Ø1/4 (Ø6.35)

0.04~0.05 (1.1~1.3)

0~0.02

(0~0.5)

0.03 (0.7)

Ø3/8 (Ø9.52)

0.06~0.07 (1.5~1.7)

0.03 (0.8)

Ø1/2 (Ø12.7)

0.06~0.07 (1.6~1.8)

0.03 (0.8)

Ø5/8 (Ø15.88)

0.06~0.07 (1.6~1.8)

0.04 (1.0)

Ø3/4 (Ø19.05)

0.07~0.08 (1.9~2.1)

0.04 (1.0)

INSTALLATION

ENGLISH

17

3 Pull back the tubing holder.

4 Remove pipe port cover and positioning

the tubing

* The feature can be changed according to

type of model.

1 Insert 4 hooks of the chassis cover into

gap of the chassis certainly.

2 Push the 6 point hook to assemble chassis

cover. Push the chassis cover ①→②.

Assembly of chassis cover

Right

Indoor unit back side view

Tubing holder

Left

Backwards

- Press on the tubing cover and unfold the

tubing to downward slowly. And then bend

to the left side slowly.

* The feature can be changed according to

type of model.

- Following bending case from right to left

directly may cause damage to the tubing.

* The feature can be changed according to

type of model.

Good case

Bad case

NOTE

!

To protect the chassis cover bended,

assembly chassis cover correctly.

NOTE

!

Installation Information. For right piping.

Follow the instruction above.

18

INSTALLATION

ENGLISH

Installation of Indoor Unit

1 Hook the indoor unit onto the upper

portion of the installation plate.( engage

the three hooks at the top of the indoor

unit with the upper edge of the installation

plate) Ensure that the hooks are properly

seated on the installation plate by moving

it left and right

2 Unlock the tubing holder from the chassis

and mount between the chassis and

installation plate in order to separate the

bottom side of the indoor unit from the

wall.

*

The feature can be changed according to the

type of model.

Piping

1 Insert the connecting cable through the

bottom side of indoor unit and connect the

cable (You can see detail contents in

'Connecting the cables' section)

View

Terminal block

Connecting cable

Cable retainer

Slide up the metal

plate cover

Installation plate

Tubing Holder

1(L) 2(N) 3(C)

2 Secure the cable onto the control board

with the cable retainer.

3 Tape the tubing pipe, drain hose and the

connection cable. Be sure that the drain

hose is located at the lowest side of the

bundle. Locating at the upper side can

cause overflow from the drain pan through

the inside of the unit.

View

Terminal block

Connecting cable

Cable retainer

Slide up the metal

plate cover

Drain hose

Connecting pipe

Connecting

cable

Tape

Drain hose

Connecting pipe

Connecting

cable

Tape

Drain hose

1(L) 2(N) 3(C)

INSTALLATION

ENGLISH

19

Insulation material

Connecting the installation pipe

and drain hose to the indoor unit.

1 Align the center of the pipes and

sufficiently tighten the flare nut by hand

* When Indoor unit (6.6 kW) is connected to

the Multi Outdoor unit, use the connector.

2 Tighten the flare nut with a wrench

3 When needed to extend the drain hose of

indoor unit, assembly the drain pipe as

shown on the drawing

Wrap the insulation material

around the connecting portion.

1 Overlap the connection pipe insulation

material and the indoor unit pipe insulation

material. Bind them together with vinyl

tape so that there may be no gap.

2 Set the tubing cutting line upward.

Wrap the area which accommodates the

rear piping housing section with vinyl tape.

3 For left rear piping, bundle the piping and

drain hose together by wrapping them

cloth tape over the range within which

they fit into the rear piping housing

section.

* Wrap the piping of the indoor unit that are

visible from the outside with vinyl tape.

Torque wrench

Indoor unit tubing

Spanner

(ﬁxed)

Connection

pipe

Flare nut

Vinyl tape(narrow)

Adhesive

Drain pipe

Indoor unit drain hose

mm inch kgf

.

cm N

.

m

Ø6.35 1/4 180~250 17.6~24.5

Ø9.52 3/8 340~420 33.3~41.2

Ø12.7 1/2 550~660 53.9~64.7

Ø15.88 5/8 630~820 61.7~80.4

Outside Diameter Torque

Indoor unit tubing Flare nut Pipes

Vinyl tape(narrow)

Connection pipe

Connecting cable

Cloth tape

Wrap with cloth tape

Indoor unit pipe

Pipe

Wrap with cloth tape

Drain hose

Pipe

Cloth tape

Gas Pipe

Liquid Pipe

Cutting Line

Good Case Bad Case

* Tubing cutting line have to be upward.

20

INSTALLATION

ENGLISH

Outdoor unit

1 Remove the tubing cover from the unit by

loosening the screw.

• 6.6 kW

• 2.5/3.5/5.0 kW

2 Align the center of the pipings and

sufficiently tighten the flare nut by hand.

* When Indoor unit(5.0/6.6 kW) is connected

to the Multi Outdoor unit, use the connector

shown above.

3 Finally, tighten the flare nut with torque

wrench until the wrench clicks.

- When tightening the flare nut with torque

wrench, ensure the direction for

tightening follows the arrow on the

wrench.

* The feature can be changed according a

type of model.

Connector

Gas side piping

(Bigger diameter)

Liquid side piping

(Smaller diameter)

Torque wrench

Outdoor unit

mm inch kgf

.

cm N

.

m

Ø6.35 1/4 180~250 17.6~24.5

Ø9.52 3/8 340~420 33.3~41.2

Ø12.7 1/2 550~660 53.9~64.7

Ø15.88 5/8 630~820 61.7~80.4

Outside Diameter Torque

La page charge ...

LG PM15SP.NSJ Manuel utilisateur

LG PM15SP.NSJ Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents