Tamasu Butterfly Europa GmbH AMICUS START Le manuel du propriétaire

1

AMICUS

START

Table Tennis Robot

Owner’s Manual | Bedienungsanleitung | Manuel d’utilisation

2

AMICUS START Table Tennis Robot

• State of the art 3-wheel ball delivery technology provides all types of spin.

• Rigid sponge wheels with a special coating for longer durability.

• Compact, solid, functional construction with integral encompassing ball collection net.

• Lightweight and easily transportable. Weights approximately 6 kg (13 lbs.).

• User-friendly Control Panel permits quick overall view with easy-to-understand adjustments.

• Random features include natural scattering of shots, random placement, or both!

• Adjust height of ball delivery to simulate anything from low serves to high lobs.

• Regulate all functions with the Control Panel located on the player’s end of the table.

Covered by a full 2-year Manufacturer’s Warranty and a 5-year guarantee of parts and service avail-

ability. See full warranty information on page 20.

CAUTIONS

• Please read this Owner’s Manual carefully before using the machine.

• This machine may only be connected to 100-230V voltage.

• The ball throw wheels rotate at high speed. Avoid touching the wheels during operation!

• Use this product only in enclosed and dry rooms.

Used properly, your AMICUS START will always be a great training partner and friend

(AMICUS is Latin for Friend).

3

IMPORTANT: Please read instructions carefully prior to use!

The Control Panel chapter describes basic adjustments of the AMICUS START table tennis robot.

More detailed instructions can be found in the Operation chapter.

Contents

1. Setup ........................................................................................................................................................................ 4

2. Control Panel ..........................................................................................................................................................6

3. Operation ................................................................................................................................................................. 7

Nomenclature .......................................................................................................................................................................7

Adjustment Of Head Height ............................................................................................................................................ 8

Starting Your Robot............................................................................................................................................................ 8

Balls Thrown To One Placement..................................................................................................................................... 8

Balls Thrown To 2 Or More Placements ....................................................................................................................... 9

Random Controls .............................................................................................................................................................. 10

The Remote Switch (optional) ....................................................................................................................................... 10

Linking the Remote Switch to the Robot.................................................................................................................... 11

Changing The Battery In Your Remote .......................................................................................................................11

Take Down, Storage, & Transport ..................................................................................................................................12

4. Maintenance & Repair ...........................................................................................................................................13

Cautions ................................................................................................................................................................................13

Checking & Adjusting Wheel Clearance .....................................................................................................................13

Replacing The Wheels .......................................................................................................................................................14

Ball Jams ..............................................................................................................................................................................15

Other Maintenance ............................................................................................................................................................16

5. Troubleshooting .................................................................................................................................................... 16

6. List of Replacement Parts .................................................................................................................................. 18

7. Technical Data .......................................................................................................................................................20

8. Warranty Information ......................................................................................................................................... 20

4

1. Setup

a. Robot and Net Assembly

b. Power Supply (Input : 100-240V, Output : 24V DC, 3A)

c. Control Panel

d. Control Panel Cable

e. Control Panel Mounting Bracket

Other parts: Hex wrenches (2 and 4 mm) for wheels, Wheel Adjust-

ment Gauge (black tube with fins), spare rub-ber bands for the Side

Nets, Velcro strips. White, steel strips to repair of the deflector

plate.

1. Place the robot on top of your table tennis table. Fold down

both sides of the net at the same time until the first stop (Photo

1A). Rotate towards you the curved tubular Support Legs into

the position as seen in Photo 1B (about 15–20 cm, or 6-8 in.,

apart).

2. Rotate the entire robot 180° with the Support Legs facing away

from you. Grasp the robot with both hands on the bottom of

the Base. Pick up the robot, angle the Support Legs downward,

slip them under the end of your table tennis table, and push the

robot onto the end of the table. Gently let go of the base and the

robot will hang by its own weight as seen in Photo 2.

Please note that AMICUS robots are designed to fit onto 25 mm

(1 in.) thick tops. If your top is less than 25 mm thick, you will

need to adjust the support legs using the height adjusting

screws. Turn the screws inward until the thickness difference

between 25 mm and your particular table surface is sufficiently

equalized.

CAUTION: Please use the included longest Velcro strip to help

secure the robot to the end of the table. This is especially im-

portant if children play around the table. The Velcro strip helps

stabilize the robot to prevent it being knocked off the table.

3. Loosen the large Black Knob found on the rear of the Ball Tube.

Rotate the head 180° and then pull the head upwards until the

3rd coloured ring on the tube is just visible (Photo 3A), then

tighten the Black Knob to hold it in place (but not too tightly).

Lastly, fasten the Head Cable coming from the head to the serial

connector found on top of the Base (Photo 3B).

Photo 1A

Photo 1B

Photo 2

5

Photo 3A Photo 3B

4. Standing behind the robot, grip the top points of the net and fold the net down on both sides until

the net fully opens (as seen in Photo 4A). Fit the plastic Corner Brackets of the net around the

corners of your table as seen in Photo 4B.

Photo 4A

Photo 4B

NOTE: You may attach the two shortest Velcro strips to the corners of your table underneath the

Corner Brackets to help the brackets stay down and stabilize the entire net.

5. Pull a Side Net along the side line of the table and pass its thick rubber band over the top of the

table’s net standard (see Photo 5A). Then loop the rubber band around the Clamp Screw that holds

the net onto the table. Attach the Side Net’s Velcro tab to its matching piece located on the Corner

Bracket as seen in Photo 5B.

Photo 5A Photo 5B

6. Plug your Power Supply into a power outlet and then into the power jack on the side of the Base.

Connect the Control Panel Cable into the jack plug (looks like a headphone jack) on the side of the

6

Base (see Photo 6A). Pull the Control Panel Cable to the opposite side of the table and connect it

to the Control Panel (see Photo 6B). Next attach the Control Panel Mounting Bracket on the side of

the table and then hang the Control Panel on the Control Panel Mounting Bracket. You may use a

Velcro strip to help secure the bracket onto the side of the table.

Photo 6A Photo 6B

2. Control Panel

60

30

0

30

4545

1515

60

Left Right

SpeedSpin

4 19

1

7 16

10 13

22

Sidespin

Low High

Trajectory

-3

-4

-2

-1

0

5

6

3

2

1

4

0

25

50

75

100

Ball /Min.

PlaceScatter

1 2 3 4 5 6

Random Erase BallAdd Ball

Back Top MoreLess

1

2

3 5

6 7 8

4

9

10

1 Ball LEDs (1–6) — When lit and solid, indicates a ball is programmed for that spot. A flashing light

indicates the Current Ball. Number of lit LEDs indicates the number of balls in your Exercise.

2 Placement Knobs (1–6) — Sets the left/right placement for that ball. Setting at the 12:00 o’clock

position tells the robot to throw that ball down the centerline. Setting a knob to the left or right of

12:00 o’clock tells the robot to throw the ball to the left or right courts, respectively. Setting a knob

to the far left or far right tells the robot to throw the ball to the left or right corner.

7

3 Add Ball Button — Press this button to add a ball to your Exercise. After pressing, a new ball is added

and its LED starts flashing.

4 Delete Ball Button — Press this button to delete a ball from your Exercise. Works for Balls 2–6. You

cannot delete Ball 1.

5 Random Button — Press once to select Random Scatter, press twice to select Random Place, and press

a 3rd time to select Random Scatter + Place. Press a 4th time to exit. See page 10 for more info.

6 Spin Knob — Increases or decreases the amount of backspin or topspin. 0 means no spin. Positive

values select increasing amounts of topspin. Negative values select increasing amounts of backspin.

7 Speed Knob — Increases or decreases the speed of the ball.

8 Sidespin Knob — Shifts the orientation of the sidespin to the left or right. 0 means no sidespin. Po-

sitions to the left select increasing degrees of left sidespin. Positions to the right select increasing

degrees of right sidespin.

9 Trajectory Knob — Raises or lowers the trajectory (throw angle). 0 indicates the midway point. Posi-

tive values indicate higher positions and negative values indicate lower positions.

10 Ball/Min knob — Decreases or increases ball frequency (Balls per Minute). Frequency ranges from

about 6 to over 100 balls per minute. 60 is the average topspin counter rate. 30-45 is often used

for beginner/novice training. Lower settings can be used for serve return, 3rd ball attack, & other

specialized drills.

3. Operation

Nomenclature

To assist in clearly communicating the various features of your robot, it is necessary to define how we

refer to certain elements. Here are various terms used throughout this manual:

Ball Type — 4 controls affect Ball Type: Spin, Speed, Sidespin, and Trajectory.

Ball Placement — the left/right location where a ball lands, determined by the Placement knob.

Basic Ball — the ball that is thrown when the Control Panel is first powered on and no adjustments have

been made. This ball will have no spin with medium speed and height.

Current Ball — the ball that is currently selected as indicated by its flashing Ball LED.

Ball 1–6 — refers to the Placement Knobs and corresponding Ball LEDs.

Exercise — a sequence of between 1 and 6 shots. Also called drill, program, or rally.

1–4 Rings — how the head height adjustment is described. E.g., 3- (coloured) Rings would mean the head

height is adjusted so 2 rings (painted on the Ball Tube) are visible (see Photo 7).

8

Adjustment Of Head Height

On most table tennis robots, the height of the

head cannot be adjusted. In contrast, AMICUS

EXPERT offers 4 different heights to better sim-

ulate realistic play. It is quite easy to adjust the

head height. From be hind the net, push the top

of the net down to reach over it. Grab the curved

ball tube with one hand and loosen the large

Black Knob with the other hand (see Photo 7).

You can then pull the tube up or push it down to

adjust head height. Lock it in place by tightening

the Black Knob. (Be careful not to tighten the

knob too much.)

IMPORTANT: Before tightening the Black Knob, be sure one of the coloured rings painted on the ball

tube is right at the top of the lower tube (see Photo 7). Be careful not to tighten the Black Knob too

tightly—you can dent the tube if tightened too much. Failure to adjust the head height correctly can

result in ball jams, double throws, missed throws, and other feed issues.

Starting Your Robot

After completing Step 5 on page 5, place about 50 or more 40 or 40+ balls into the Ball Collection

Tray. The Ball 1 LED should be flashing yellow Turn Ball/Min knob to your desired setting (you will hear

the wheels start spinning) and balls will begin loading into the machine. After a few seconds, the first

ball will reach the top of the ball tube. Turn Ball/Min knob to 0 to halt ball feed.

Grab your racket and prepare to return balls from your robot. Turn all knobs in middle position, then

turn the Ball/Min knob to your desired setting and observe where the balls land in relation to the

centerline. If balls are delivered either left or right of the centerline, then stop ball delivery. At the

robot, loosen the large Black Knob on the rear of the Ball Tube (see Photo 6B) and rotate the head in the

direction necessary for balls to land closer to the centerline. Repeat until all balls are landing close to

the centerline, then turn Ball/Min to 0.

Balls Thrown To One Placement

The easiest way to learn the various controls is to start with a single ball delivered to one location. On

the AMICUS START, all Balls in an Exercise will have 1 Ball Type (other models allow different Ball Types

for each Ball). Upon powering on the Control Panel, only the Ball 1 LED should be lit and it should be

flashing. If any other Ball LED is lit, press the Delete Ball button until only Ball 1 LED is lit.

To adjust Ball Type:

• The Trajectory knob (9) raises or lowers the ball trajectory (throw angle). Although there are only

9 settings marked on the Control Panel, there are actually about 15 steps of adjustment between

each marked increment for a total of over 150 steps of adjustment. This allows you to finely tune the

Trajectory from very low for serves, where the ball bounces first on the robot’s side of the net, cross-

es the net, and then bounces a second time on the player’s side, to high, where the ball is thrown a

couple of feet over the net.

Photo 7

9

• The Sidespin knob (8) changes the orientation of the sidespin on the ball. The zero setting means

there is no sidespin on the ball. Each marked increment represents a 15° change in orientation,

except for the first mark, which is 30°. Settings to the right of zero are degrees of right sidespin and

settings to the left are degrees of left sidespin.

• The Speed knob (7) reduces or increases the speed of the ball. There are 22 increments of speed

adjustment, from 1 for very slow, to 22 for very fast.

• The Spin knob (6) reduces or increases the amount of spin on the ball. A setting of zero indicates

no spin (dead ball). Settings to the right of zero (1 to 6) indicate stronger and stronger amounts of

topspin. Settings to the left of zero (-1 to -4) indicate stronger and stronger amounts of backspin.

To adjust Ball Placement (also called place or location):

• The Placement knobs (2) determine the left to right landing spot of each ball. 12:00 o’clock

corresponds with the centerline of the table. Settings to the right of 12:00 correspond with balls

progressively landing closer and closer to the right corner of the table. Settings to the left of 12:00

correspond to balls landing progressively closer and closer to the left corner.

To adjust Ball Frequency:

• The Ball/Min knob (10) decreases or increases the rate, or frequency, of shots. You can select

settings from about 6 to over 100 balls/min. When turned to 0, all motors, including the ones for ball

feed and ball throwing, are turned off and go silent.

Once you have adjusted the above settings to your liking, turn up Ball/Min to have the robot deliver

your chosen ball type to your chosen location at the desired frequency. If it is not what you want, turn

Ball/Min to 0 and change the settings until you get the type of shot you want. Then try again. Although

you may find it easiest to stop play to make changes to the settings, you can also change settings on

the fly, without stopping play.

Balls Thrown To 2 Or More Placements

Once you have the Ball Type selected as described in the preceding section, it is a simple matter to

have that same shot delivered to more than one place. To add additional Balls to your Exercise, press

the Add Ball button. Ball 2 LED will begin flashing, which indicates it is now the Current Ball (and Ball 1

LED will stop flashing to indicate it is no longer the Current Ball). To select a different landing spot for

Ball 2, all you have to do is change the Placement setting.

You can continue this same procedure to add up to 6 balls to your Exercise. With each added Ball, you

will notice that the corresponding LED will light up. By looking at the number of Ball LEDs that are lit,

you can quickly tell the number of shots in an Exercise.

To play your Exercise, turn up Ball/Min, and AMICUS will throw the balls in order, starting with the ball

that has a flashing LED. E.g., if you have 3 balls with lit LEDs and #2 is flashing, AMICUS will throw Ball 2,

followed by Ball 3, and followed by Ball 1. Then it will start over with Ball 2. It will continue this order of

thrown balls until you turn Ball/Min to 0.

If you want the Exercise to start with a particular Ball each time, be sure to turn off delivery when

the desired Ball’s LED is flashing. In the above example, if you wanted the Exercise to start with Ball 1

10

instead of Ball 2, stop the Exercise when Ball 1 is flashing. Upon restarting the drill, Ball 1 will be flashing

and will be the first Ball to be thrown.

Best practices: Before playing a multi-ball exercise, look at the Ball Placement knob of each Ball with

a lit LED to get an idea of where each Ball will be delivered and in what order. Then look at the Ball Type

knobs to determine the type of Ball that will be thrown. This allows you to be prepared for the sequence

of shots and helps you to decide what stroke to use to return the shots.

Please note: Because the distance is greater from the robot to the corners of the table than from the

robot to the center of the table, AMICUS START automatically varies the length of ball delivery so an

Exercise runs correctly when it contains mixed placements. This is possible thanks to the built in pro-

gram and the special placing mechanism.

Random Controls

AMICUS START offers 3 types of randomization—Random Scatter, Random Place, and Random Scatter

+ Place. To activate, press the Random button. Your first press selects Random Scatter (the Scatter

LED will light up). Press Random a second time and the Place LED will light up (and Scatter LED dark-

ens). Press Random a third time and both Scatter and Place LEDs will light up. Press a fourth time to

turn Random off (and both Scatter and Place LEDs darken).

Random Scatter is similar to the less precise shots that a human might deliver. Without Random

Scatter, the robot typically delivers shots within an area approximately 13 cm (5in.) in diameter. But with

Random Scatter, balls are delivered in an enlarged area of approximately 40cm (16in.) diameter.

Random Place requires at least 2 Balls in an Exercise. If there is only a single Ball, the Place LED will

not light up. With Random Place on, the robot will randomly select one of the Placements programmed

for the Exercise and throw the ball there in an unpredictable order. E.g., let’s say an Exercise uses

Placements of Forehand, Center, and Backhand. Without Random Place activated, the order of throws

will always be the same—FH, Center, BH. But with Random Place on, the order could be something like

Center, FH, BH, BH, FH, Center, etc..

Random Scatter + Place combines the above two random functions. The landing spots for every Ball are

enlarged and the Placements are randomized.

Best practices: Avoid programming landing spots that are close to the sideline, end line, or table net

when using Random Scatter. If you do, many balls are likely to be shot off the side or end of the table or

into the net because of the enlarged area of the landing spots with Random Scatter. When using Ran-

dom Place, if you want throws delivered to one spot more often than other spots, program more Balls

with the desired placement. E.g., if an Exercise has 4 Balls with one of them placed to the Forehand and

three placed to the Backhand, there is a 1 in 4 chance a ball will be delivered to the Forehand, but a 3 in

4 chance a ball will be delivered to the Backhand. Lastly, while Random Place must have at least 2 Balls

in the Exercise, Random Scatter can be used with single ball exercises.

The Remote Switch (optional)

The small wireless remote (looks similar to an automobile key fob) has a range of 4–5 m (13–16 feet) and

has the following functions:

11

1. If Ball/Min on the Control Panel is set to 0, pushing the top button

(Start) of the remote will throw 1 ball (current ball) of the Exercise shown

on the Control Panel.

2. If Ball/Min on the Control Panel is not set to 0, pushing the top button

(Start) of the remote will cause the exercise shown on the Control Panel

to start playing at whatever frequency the Ball/Min is currently set to.

The play stops when pushing the (Stop) button.

3. Pushing the (+) button during play will increase the frequency, while

pushing the (-) will decrease the frequency.

Linking the Remote Switch to the Robot

Each remote is linked to an individual Robot body. This linkage is done at the factory and each Robot

and Remote pair is kept together throughout the manufacturing process. In case you buy more Re-

motes or a new one, you need to link each Remote to your Robot. Here are the steps to perform the

Linking procedure:

1. Hold down the Random button on your control panel until 4 LEDs on the control panel will light up.

The 4 LEDS represent a countdown for the linking procedure. Every 3 seconds, one of the LEDs will

stop lighting. If all LEDs are dark, the linking process is ended.

2. During the countdown, press any one of the buttons on the remote switch.

3. The linking is completed. The robot will automatically end the linking process and resume normal

operation.

4. Test your remote by pressing the A button to see if your robot begins throwing balls.

Changing The Battery In Your Remote

The Remote is powered by two 3V, CR2016 button cell batteries. After long use, the batteries will run down

and will need to be replaced. After purchasing replacement batteries, open your remote by inserting a coin

or flathead screwdriver in the slot located on the wide end of the Remote and twisting to pop it open.

Remove the circuit board containing the battery. With your thumbnail, pull the battery holder away

from the circuit board. Pop the two depleted batteries out of the battery holder and replace with fresh

batteries. When inserting into the battery holder, be sure the positive side (+) of both batteries face up.

Re-insert the battery holder into the circuit board.

Reassemble the circuit board into the top housing (battery side up). Position the U-shaped metal piece

around the outside of the top housing. Then place the bottom housing on top and press the top and

bottom housings together, starting at the narrow end and working your way to the wide end until the

housings snap in place.

12

Take Down, Storage, & Transport

Upon finishing your training session, please power off your robot by unplugging from power; or alterna-

tively, plug your robot into a power strip and use the switch on the strip to turn the power off to your

robot.

If you’re ready to remove your robot from the table temporarily, please follow these steps:

1. Unplug the robot from power and from the base. Unplug

the Control Panel Cable from the base and the Control

Panel. Roll these cables up and place them temporarily

on your table.

2. Disconnect the rubber bands that connect your Side

Nets to your table. Place the Side Nets in the Ball Trays

of the Main Net.

3. Fold up the Main Net until the first stop of the folding mechanism. Unhook your robot from your

table and set it on your table with the open end facing you.

4. Place your rolled-up cables, Control Panel, and Control Panel Mounting Bracket in the center area

of the net on top of the balls (you do not need to remove the balls).

5. Stand your robot upright on the floor off to the side of your table or in a nearby closet. When you’re

ready to train again, it’s a quick, easy matter to set your robot back up on your table.

If you’re removing the robot for transport or long-term storage, we recommend placing your robot

into the included Carrying Case with these additional steps:

6. Loosen the Black Knob on the rear of the Ball Tube, turn the head around 180° so it faces into the

net, and lower the head to only 1 ring. Then retighten the knob.

7. Remove the cables, Control Panel, and bracket from the center area and place those items in the

storage pockets of the Carrying Case. The Carrying Case is also a handy place to store this manual,

balls, spare parts and tools, and other items that came with your robot.

8. Finish folding up the net until the two Net Corner Brackets touch and their mating Velcro pieces

adhere to one another. You may need to help the net uprights fold down. You can also stuff parts of

the net that are sticking out into the central part of the net.

9. Lay the robot net side down into the Carrying Case and secure it in place with the 2 straps found on

the bottom of the case.

13

4. Maintenance & Repair

Cautions

1. Before performing any maintenance or repairs, unplug your robot from power.

2. Be sure no objects like dented balls, hair, string, etc. fall into the net and then work their way into

the machine where they can cause ball jams or interfere with correct operation.

3. Table tennis robots work best with clean, worn balls. When adding new balls, please wash the gritty

manufacturing powder off them first with warm, soapy water, then rinsing and drying before using.

(Butterfly brand balls are pre-washed at the factory so this step is unnecessary with new Butterfly

balls.) Keep your playing area clean to prevent balls that have rolled on the floor from picking up dirt

and introducing that dirt into the machine.

4. The wheels have a special coating that prolongs their lifetime. Do not attempt to clean the wheels

with any chemical, as the chemical can be detrimental to the coating.

5. AMICUS robots are designed for use in clean, dry, indoor rooms. Do not use outdoors or in any wet

or damp environment. Avoid leaving your robot in a hot car or trunk.

6. Use only 40 or 40+ balls in your robot. The better ball you use (3-star are best), the more consistent

your robot can throw that ball.

Checking & Adjusting Wheel Clearance

AMICUS wheels are very durable (at least 1000

hours). But eventually, these wheels will wear

down after long or intense use. As the wheels

wear down, the space among the 3 wheels

enlarges, causing the wheels to lose their grip on

the ball. Dropping the robot or other similar trau-

ma during transport or use can also cause this.

One sign that the space among the wheels needs

to be adjusted is that the machine releases the

balls at irregular lengths at high speed. When the

length of the ball throws becomes irregular, the

space among the 3 wheels needs to be adjusted.

To check the space among the wheels, place

the Wheel Adjustment Gauge (black tube with 3

fins) in the space among the 3 wheels, fins end

first, and so the fins do not touch any wheel (see

Photo 8A). Now move it in and out. If the distance

is correct, the gauge can be moved in and out

easily, but with the wheels just barely touching

the outer surface of the gauge (wheels may turn

slightly as the gauge is moved). If the wheels

do not grip the gauge at all, or conversely, they

Photo 8A

Photo 8B

14

tightly grip the gauge, then wheel adjustment is

called for.

To adjust the wheels, push the gauge into the

end of the Ball Tube where the ball comes out so

it is held rigidly in place. Then use the 4 mm hex

wrench found in the accessories to loosen the

hex screw near the cover of the motor (see Photo

8B). Now move the motor (gripping its cover)

either towards or away from the gauge until the

wheel barely touches it (see Photo 8C). Lastly,

tighten the 4 mm hex screw to hold the wheel in

place. Do this with all 3 motors.

Please note: The diameter of the adjusting tube is 35 mm, which is the ideal amount of space among the

3 wheels. The robot functions correctly up to a diameter of 37-38 mm.

Replacing The Wheels

When the wheels can’t be adjusted anymore, or the special coating on the wheels has worn off, the

wheels should be replaced. To do so, start with the lower wheel. Using the smaller 2 mm hex wrench,

loosen the small setscrew that holds the wheel onto the shaft of the motor (see Photo 9A) Before tak-

ing it off, check and memorize the exact position of the wheel on the shaft of the motor. Pull the wheel

off the motor shaft and remove the three #1 Phillips screws that hold the foam wheel onto the hard

plastic hub. Remove the wheel from the hub and replace with a new wheel. Then refasten the hub to the

wheel. Slip the wheel assembly onto the motor shaft until the position of the original wheel is reached.

Tighten the setscrew.

Now manually spin the wheel to be sure it is not rubbing on any surface. If so, loosen the setscrew

and slightly move the wheel’s position on the shaft and try again until the wheel no longer rubs on any

surface. Lastly, tighten the setscrew securely.

For the upper motors, the procedure is a little bit different. Begin by removing the 4 mm hex adjust-

ment screw (see Photo 9B). Grab a hold of the motor cover, and pivot the entire motor mechanism away

from the Ball Tube (see Photos 9C & 9D). Now you can remove the old wheel and push the new wheel

on the motor shaft, and then refasten the wheel onto the motor shaft using the same procedures as

described above for the lower wheel, then replace and tighten the 4 mm hex screw.

The wheel may not be as easy to remove from the shaft, or put back on the shaft, due to the close prox-

imity of the Head Panel and the Oscillation & Trajectory Motor Cover. But because the wheels are foam,

the wheel can be removed and replaced with a little force to bend the foam out of place. If removing

the wheel is too difficult, you can remove the Oscillation and Trajectory Motor Cover to provide more

room for wheel removal and replacement.

Even if only one of the upper wheels has been damaged, we recommend replacing all upper wheels at

once, to ensure the robot does not become inaccurate After replacing wheels, adjust the wheel spacing

as described in the previous section, Checking and Adjusting Wheel Clearance.

Photo 8C

15

Photo 9A Photo 9B

Photo 9C Photo 9D

Ball Jams

Your robot is equipped with a special system

to detect and react to problems in the ball

channel. When the system detects a problem, it

will attempt to automatically clear the ball jam

by turning the Ball Feed Motor and the wheels

forward and backward 7-8 times.

If the error can’t be resolved so, all motors stop

and the system shows an error code on the

display (Er1 or Er2). Er1 indicates a problem in the base of the robot, and Er2 indicates a problem in the

head of the robot (see Troubleshooting, p. 17).

To begin troubleshooting, first disconnect power. For an Er2 code, check that a ball is not stuck among

the 3 wheels (commonly occurs after moving the head height down). If so, simply remove those balls by

hand and resume normal operations.

For an Er1 code, remove the head by disconnecting the Head Cable, loosening the large Black Knob on

the rear of the Ball Tube, and pulling up on the head. Then tilt the entire net system forward to expose

the access slot on the bottom of the Base (see Photo 10). Take a long rod-like tool (screwdriver, dowel,

etc.) that is about 30 cm (12 inches) long, insert it into the access slot, and push balls out the top of the

lower Ball Tube.

Photo 10

16

Once clear of balls, with the help of a flashlight, inspect inside the ball channel and clear out any foreign

objects or dirt. With the ball channel empty, test ball feed to see if the ball stirring mechanism rotates

when Ball/Min knob is turned up. Without any balls in the machine, the ball stirring mechanism should

rotate approximately 11-12 times before it stops automatically. If so, place balls back in machine and

resume normal operations. If not, it is indicative of problems with the Ball Feed Motor and/or the Ball

Feed Mechanism and you should contact your an AMICUS Service Center for further assistance.

Other Maintenance

After a lot of use, the White Strip found on the inside upper surface of the Deflector Plate can wear out

and the machine becomes inaccurate. In such case, without dismounting the Deflector Plate, clean the

White Strip with isopropyl alcohol to remove all dirt.

The rest of the machine needs no maintenance. However, you can remove dirt and dust from the sur-

face of the robot with a moist cloth and a mild, water-based cleaner as necessary.

5. Troubleshooting

Problems Solutions

1. Head or Support Legs point

towards net.

A. Loosen the large Black Knob on the rear of the Ball Tube,

then rotate head 180° so head points away from net. Grasp

Support Legs and rotate them away from net (p. 4).

2. The robot does not function.

No lights, no sound, no

movement.

A. Control Panel Cable loose or unattached. Check connection

at Control Panel & Base.

B. Plug Power Supply into power outlet and connect other end

to power jack on the Base (see Photo 6A, p. 6).

C. Is green LED on Power Supply lit? If not, check outlet for

power. If power is present, replace Power Supply.

3. Control Panel LEDs light up,

but no balls are thrown.

A. Set the Ball/Min knob higher than zero.

B. If using Remote and Ball/Min is higher than zero, press but-

ton A to start ball delivery.

4. Balls thrown to wrong

places.

A. Are there rubber bands around the Deflector Plate and/or is

there a blue foam pad above it? If yes, remove those parts so

Deflector Plate can move freely. Those parts are used only

during transport.

B. Is Random on? If so, turn off (p. 10).

C. Unplug all 3 cable connections and then re-plug. Connect

cable to Control Panel last.

D. Check pins of Head Cable to be sure none are bent or miss-

ing. There are 15 pins.

E. If robot throws balls further to one side than the other,

Deflector Plate may need to be adjusted or replaced. Consult

an AMICUS service center.

17

5. Balls thrown at irregular

depths.

A. Check wheel clearance (p. 13).

B. Wheels worn. Replace all 3 wheels (p. 14).

C. Clean White Strip on Deflector Plate with isopropyl alcohol.

6. Double throws or missed

throws.

A. Head height improperly adjusted (p. 8).

7. Random Place LED won’t

turn on (p. 10).

A. Exercise needs at least 2 Balls. If only 1 Ball LED is lit, add a

second Ball (p. 8 & 9).

8. All 6 Ball LEDs are flashing. A. Is ball stuck among the 3 wheels? If so, turn off power, and

then remove that ball.

B. Defective or oversized ball or foreign object jamming the lower

ball channel. Clear channel and test ball feed (p. 15).

C. Dirty or unwashed new balls are being used. Clear ball chan-

nel of balls, then wash the balls to remove grit, rinse, and dry

before placing back into robot.

D.

Is a foreign object or ball preventing the Ball Stirring Springs

from moving? If so, remove that foreign object or ball.

E. Was Black Knob tightened too much, denting the upper Ball

Tube? Disconnect the head, and roll a ball up and down the

Ball Tube to check if it is obstructed. If so, call an AMICUS

service center.

F. Bad Ball Feed Motor, broken gears or motor support. Call

AMICUS service center.

G. Bad Ball Throw Motor. Replace.

H. Overheated electronics. Switch off power and wait several

minutes. If problem disappears, resume operations. If prob-

lem remains, consult an AMICUS service center.

Attention: If you are not able to solve the problems with the help of the Troubleshooting chart,

please consult an AMICUS service center. If you see any exposed wires on the Power Supply,

disconnect from power immediately and replace the Power Supply. Failure to do so could result in

serious harm.

18

6. List of Replacement Parts

1 Robot body bottom part

2 Robot body upper part

3 Feeding shaft

4 Feeding motor

5 Hanging mechanism

6-7 Net streching tubes (Left-right)

8 Mover tubes

9 Ball collecting net

10 Ball catching net

11 Ball feeding tube

12 Ball throwing head

13L Left top shooting motors

13B Right top shooting motors

13LO Lower shooting motor

14 Throwing wheels

15 Throwing motor cover

16 Ball placing head

17 Placing motor right-left

18 Placing motor high-low

19 Deflector

20 Placing motor cover

21 spacer tubes and screws

22 Power electronic

23 Power electronic cover plate

24 Extension cord - Start,Expert

25 Control box hanger

26 AMICUS Start controlbox

27 AMICUS Expert controlbox

28 7 inch tablet (Prime)

29 24V 3A adapter

30 AC cable for adapter

31 Charger cable (Prime)

19

20

7. Technical Data

Electrical Specifications: 100-230V, 50-60Hz AC, approximately 60W Can be operated in a temperature

range of 0–40°C (32–104°F).

Weight: 6 kg with net (13.2 lbs.). Overall dimensions (folded, with net): Height 0.75m, Width

0.28m, Depth 0.25m (2.5 x 0.9 x 0.8 feet).

An examination was done for the power supply:

Conformity with Low Voltage Directive 73/23/EEC, as last amended by EEC Directive

93/68/EEC—Registration #: AN 50091861 0001, Report #: 17004848 001. Also Test Reports # NTEK-

2010NT1115351E and NTEK-2010NT1115353SS.

The AMICUS START table tennis robot is permitted to bear the CE trademark.

Manufacturer: Tamasu Butterfly GmbH, Kommunikationsstr. 8, 47807 Krefeld

8. Warranty Information

FULL 2-YEAR MANUFACTURER’S WARRANTY

Manufacturer warrants to the original retail purchaser this product to be free from defects in material

and workmanship for a period of 2 years from date of purchase.

Should this product become defective due to material or workmanship during the warranty period,

contact your AMICUS support describing the problem. Always provide your serial number and dated

proof of purchase. We will provide you with return authorization and shipping instructions, or provide

a replacement part and instructions for replacement. If you are asked to return the product, pack it

securely.

If defective as provided by the terms of this warranty, we will, at our option, repair or replace the

product and return it prepaid (areas outside a service center’s assigned territory will carry a shipping

charge).

This warranty is not transferable and does not cover normal wear and tear, or damage caused by im-

proper handling, installation, or use. This warranty is void if the product is in any way abused, damaged,

or modified from its original state.

This warranty gives you specific legal rights, and you may have other rights that may vary from state to

state, or country to country.

Owner’s Manual | Bedienungsanleitung | Manuel d’utilisation

La page charge ...

Tamasu Butterfly Europa GmbH AMICUS START Le manuel du propriétaire

Tamasu Butterfly Europa GmbH AMICUS START Le manuel du propriétaire

dans d''autres langues

Autres documents